Vauxhall Cascada (2013) manual

Select a language NL 100%

View a manual of the Vauxhall Cascada (2013) below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Vauxhall
  • Product: Car
  • Model/name: Cascada (2013)
  • Filetype: PDF
  • Available languages:

Table of Contents

Page: 0
Vehicle features
Cascada
Quick Reference Guide
Refer to Owner’s Manual for detailed information.
Illustrations may depict left-hand drive vehicles.
Operation is similar for right-hand drive vehicles.
Depending on the model variant, special equipment
and accessories, the scope of equipment on your
vehicle may differ from the descriptions in this guide.
KTA-2762/1 August 2013
*KTA-2762-1*
Vehicle features Vehicle features
Unlocking
Press button c to unlock doors,
boot lid and fuel flap. Press and
hold button c to open the soft top
and the windows.
Locking
Close doors, boot lid and fuel filler
flap. Press button e. Press and hold
button e to also close the soft top
and the windows.
Press button e on the remote
control twice briefly within
15 seconds to deadlock all doors
and activate anti-theft alarm
system.
The vehicle can also be configured
to unlock only the driver’s door,
boot lid and fuel filler flap when
pressing button c once on the
remote control. Pressing button c
twice will unlock the entire vehicle.
Electronic immobiliser:
Activated automatically when key
is removed from ignition switch.
1. Power windows
2. Exterior mirrors
3. Cruise control, speed limiter,
forward collision alert
4. Side air vents
5. Turn signals, headlight flash,
low beam, high beam, high
beam assist, exit lighting,
parking lights, buttons for
Driver Information Centre
6. Instruments
7. Steering wheel controls
8. Driver Information Centre
9. Wiper and washer systems
10. Central locking system,
hazard warning flashers,
Sport mode, Tour mode,
LEDs for front passenger seat
belt and airbag deactivation
11. Info-Display
12. Anti-theft alarm system LED
13. Centre air vents
14. Glovebox, fusebox
15. Traction Control system,
Electronic Stability Control,
parking assist,
lane departure warning,
ECO button (stop-start system)
16. Climate control system
17. AUX input, USB input
18. Power outlet
19. Soft top operation switch,
central window switch
20. Selector lever
21. Parking brake
22. Ignition switch with
steering wheel lock
23. Horn, driver airbag
24. Bonnet release lever
25. Storage compartment
26. Steering wheel adjustment
27. Light switch, fog lights,
headlight range adjustment,
instrument illumination
Manual transmission:
Reverse: With vehicle stationary,
wait 3 seconds after depressing the
clutch pedal, then press release
button on selector lever and
engage gear.
If the gear does not engage, set the
lever to neutral, release the clutch
pedal and depress again; then
repeat gear selection.
Do not slip the clutch unnecessarily.
When operating, depress clutch
pedal fully. Do not use the pedal as
a foot rest.
Automatic transmission:
P = Park
R = Reverse
N = Neutral
D = Automatic (drive) mode
with all gears.
The selector lever can only be
moved out of P when the ignition is
on and the brake pedal is applied.
To engage P or R, press the release
button on the selector lever.
When position N is selected,
depress brake pedal or apply the
parking brake before starting.
Automatic transmission,
Manual mode:
Move selector lever from D to the
left then forwards or backwards.
+ = Shift to a higher gear
- = Shift to a lower gear
If a higher gear is selected when
vehicle speed is too low, or a lower
gear when vehicle speed is too
high, the shift is not executed. This
can cause a message in the Driver
Information Centre.
Starting the engine:
„ Turn key to position 1
„ Move steering wheel slightly to
release steering wheel lock
„ Manual transmission in neutral
with clutch depressed
„ Automatic transmission in P or N
with brake pedal depressed
„ Do not accelerate
„ Diesel engines: turn key to
position 2 for preheating and
wait for ! to extinguish
„ Turn key to position 3 and
release
The key does not have to be held in
position 3 - the Automatic Starter
Control ensures that the system will
go on starting automatically until
the engine is running. Because of
the checking procedure, the engine
starts running after a short delay.
Stop-start system:
When conditions allow, the system
switches off the engine to save fuel
and reduce emission levels if the
vehicle is at a low speed or at a
standstill, e.g. at traffic lights or in a
traffic jam. It starts the engine as
soon as the clutch is depressed.
To activate an Autostop:
„ Depress clutch pedal
„ Shift selector lever to neutral
„ Release the clutch pedal
The needle points to AUTO STOP in
the tachometer. To restart engine,
depress clutch again.
Deactivate Stop-Start system
manually by pressing the eco
button on the instrument panel.
The LED in the button extinguishes
to confirm deactivation.
Manual parking brake:
Always apply firmly without
operating release button and
apply as firmly as possible on uphill
or downhill slopes.
To release, pull lever up slightly,
press release button and lower
lever fully.
To reduce the operating forces,
depress the brake pedal at the
same time.
Closing the boot lid:
Use the interior handle on the
underside of the boot lid to close.
Do not touch the brand emblem
whilst closing as this could unlock
the boot lid again.
Blockage of boot lid
The boot lid can only be opened
when the soft top is completely
opened or closed. The soft top lid
must be closed.
Electrical parking brake:
Pull switch J for approx. one
second, parking brake operates
automatically with adequate force.
For maximum force, e.g. when
parking with trailer attached or on
inclines, pull switch J twice.
The parking brake can always be
activated, even if the ignition is off.
Before leaving the vehicle, check
parking brake status.
To release, switch on ignition, keep
brake pedal depressed and push
switch J.
Drive away function
Depressing clutch pedal (manual
transmission) or engaging drive
gear (automatic transmission) and
then depressing the accelerator
pedal releases electrical parking
brake.
Unlocking and opening the boot
lid:
Press button c on remote control to
unlock boot lid (together with doors
and fuel filler flap).
Then push the brand emblem at
the bottom half to open the boot
lid.
- or -
Press button x on remote control
to open boot lid while the vehicle
remains locked.
Opening the bonnet:
Pull release lever located below
instrument panel on driver’s side
and return it to its original position.
Push safety catch to the right and
open the bonnet.
Secure the bonnet support.
If the bonnet is opened during an
Autostop, the engine will be
restarted automatically for safety
reasons.
Closing the bonnet:
Before closing, press the bonnet
support into its holder.
Lower the bonnet and allow it to
drop into the catch from a low
height (approx. 20-25 cm).
Check that the bonnet is engaged.
Refuelling:
Before refuelling, switch off engine
and any external heaters with
combustion chambers.
Switch off any mobile phones.
Fuel filler flap is located at right
rear side of vehicle.
The fuel filler flap can only be
opened if the vehicle is unlocked.
Release the fuel filler flap by
pushing the flap.
To open, turn the fuel filler cap
slowly to the left.
Vehicle security
Tyre pressure:
Check tyre pressures, including the spare, every 14 days and prior to any long journey; tyres should be
checked when cold. This also applies to vehicles with tyre pressure monitoring system.
The tyre pressure data refers to cold tyres. It applies to summer and winter tyres.
Always inflate the spare tyre to the value specified for full load.
The ECO tyre pressure serves to achieve the smallest amount of fuel consumption possible.
Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and increase tyre wear.
Warning:
If the pressure is too low, this can result in considerable tyre warm-up and internal damage, leading to tread
separation and even to tyre blow-out at high speeds.
Tyre pressure (psi)
Comfort setting for upto
3 people
Engine Tyres Front Rear
A14NEL, 225/55 R17 34 34
A14NET, 235/55 R17 34 34
A16XHT 235/50 R18 34 34
245/45 R18 34 34
235/45 R19 34 34
245/40 R20 34 34
A20DTH, 225/55 R17 36 34
A20DTR 235/55 R17 36 34
235/50 R18 36 34
245/45 R18 36 34
235/45 R19 36 34
245/40 R20 36 34
All Temporary spare 61 61
Tyre pressure (psi)
ECO setting for upto
3 people
Engine Tyres Front Rear
A14NEL, 225/55 R17 41 41
A14NET, 235/55 R17 41 41
A16XHT 235/50 R18 41 41
245/45 R18 41 41
235/45 R19 41 41
245/40 R20 41 41
A20DTH, 225/55 R17 41 41
A20DTR 235/55 R17 41 41
235/50 R18 41 41
245/45 R18 41 41
235/45 R19 41 41
245/40 R20 41 41
All Temporary spare -1)
-1)
1)
Do not use ECO tyre pressure for this
tyre.
Tyre pressure (psi)
With full load
Engine Tyres Front Rear
A14NEL, 225/55 R17 35 41
A14NET, 235/55 R17 35 41
A16XHT 235/50 R18 35 41
245/45 R18 35 41
235/45 R19 35 41
245/40 R20 35 41
A20 DTH, 225/55 R17 38 44
A20DTR 235/55 R17 38 44
235/50 R18 38 44
245/45 R18 38 44
235/45 R19 38 44
245/40 R20 38 44
All Temporary spare 61 61
Engine oil:
Check engine oil level manually on a regular basis to prevent damage to engine.
Ensure that the correct specification of oil is used.
Check with vehicle on a level surface. Engine must be at operating temperature and switched off for at least
5 minutes. Pull out dipstick, wipe clean, insert to stop on the handle, pull out and read engine oil level.
Insert dipstick to stop on handle and make half a turn.
Important:
It is the owner’s responsibility to maintain the correct level of an appropriate quality oil in the engine.
Do not allow the engine oil level to drop below the minimum level!
Refuelling (continued):
The fuel filler cap can be retained in the bracket on the fuel filler flap.
To refuel, fully insert the pump nozzle and switch it on. After the automatic cut-off, the tank can be topped
up with maximum two doses of fuel. Wipe off any overflowing fuel immediately.
To close, turn the fuel filler cap to the right until it clicks. Close the flap and ensure it engages.
Petrol engines - use unleaded fuel meeting specifications of EN 228 or E DIN 51626-1 or equivalent.
Diesel engines - use diesel fuel meeting specifications of EN 590.
Fuel tank capacity - 56 litres.
Page: 1
Vehicle features Vehicle features
Vehicle features Vehicle features
Longitudinal seat adjustment:
Pull handle, slide seat, release
handle.
Danger:
Do not sit nearer than 25 cm from
the steering wheel, to permit safe
airbag deployment.
Seat backrests:
Pull lever towards the rear, adjust
inclination and release lever. Allow
the backrest to engage audibly.
Do not angle the backrest too far
back. We recommend a maximum
rake of approx. 25o
.
Seat height:
Lever pumping motion.
up = seat higher
down = seat lower
Head restraint adjustment:
Press the release button, adjust
height and engage.
Pull the head restraint forwards
slowly to adjust to one of several
horizontal positions and engage.
The upper edge of the head
restraint should be at upper head
level.
Seat belt:
Withdraw seat belt from retractor,
guide it untwisted across the body
and insert latch plate in belt buckle.
To release belt, press red button on
belt buckle.
Automatic anti-dazzle interior
mirror:
Dazzle from following vehicles at
night is automatically reduced if
the vehicle is equipped with an
automatic anti-dazzle interior
mirror.
The lever will not be present on the
underside of the mirror housing.
Exterior mirrors:
Select the relevant exterior mirror
by turning the control to left (L) or
right (R).
Swivel the control to adjust the
mirror.
In position 0 no mirror is selected.
Folding in exterior mirrors:
Manually:
Apply slight pressure to outer edge
of mirror housing.
Electrically:
Turn control to 0 and push control
down to fold exterior mirrors.
Push control down again to return
them to their original position.
If an electrically folded mirror is
manually extended, pushing the
control down will only electrically
extend the other mirror.
Operating windows and soft top
with remote control (continued):
Press button e once briefly: the
doors are locked.
Hold button e pressed once more:
the soft top and the windows will be
closed. Hold button e pressed until
soft top is completely closed.
Release button e during closing of
the soft top: movement stops for
10 seconds; press button e again
to continue closing the soft top.
If the soft top is already closed with
the windows open, press button e
for two seconds after locking to
close the windows.
Lighting:
Turn light switch:
AUTO= Automatic light control:
Headlights are switched
on and off automatically
m = Activation or deactivation
of automatic light control
(switch returns to AUTO)
O = Off
8 = Sidelights
9 = Headlights
Press light switch:
> = Front fog lights
r = Rear fog light
Turn thumb wheel:
q = Headlight range
adjustment
A = Instrument panel
illumination
Turn and lane-change signals:
Lever up = Right turn signal
Lever down = Left turn signal
If the lever is moved past the
resistance point, the turn signal is
switched on constantly. When the
steering wheel is moved back the
turn signal is automatically
deactivated.
For three flashes, e.g. when
changing lanes, press the lever until
resistance is felt and then release.
Move lever to resistance point and
hold for longer indication.
Automatic light control:
When the function is switched on,
with the engine running the system
switches between daytime running
lights and headlights, depending
on external lighting conditions and
information from the rain sensor.
Daytime running lights:
Increases visibility of the vehicle
during daylight.
Automatic headlight activation:
During poor lighting conditions the
headlights are switched on.
Headlights are also switched on
when windscreen wiper has been
activated for several wipes.
Tunnel detection:
When a tunnel is entered, the
headlights switch on automatically.
Front fog lights:
Operated with the > button.
Light switch in position AUTO:
Switching on front fog lights will
switch headlights on automatically.
Rear fog light:
Operated with the r button.
Light switch in position AUTO:
Switching on rear fog light will
switch headlights on automatically.
Light switch in position 8:
Rear fog light can only be switched
on with front fog lights.
Headlight range adjustment:
To adapt headlight range to the
vehicle load to prevent dazzling of
other road users, turn thumb
wheel ? to required position.
0 = Front seats occupied
1 = All seats occupied
2 = All seats occupied and
load compartment laden
3 = Driver’s seat occupied and
load compartment laden
Windscreen and headlight
washer:
Pull lever. Washer fluid is sprayed
onto the windscreen and the wiper
wipes a few times.
If the headlights are on, washer
fluid is also sprayed onto the
headlights, provided that the lever
is pulled for a sufficiently long
period.
The headlight washer system is
then inoperable for 5 wash cycles
or until engine or headlights have
been switched off and on again.
Headlight flash, high beam and
low beam
Headlight flash = Pull lever
High beam = Push lever
Low beam = Pull or push lever
High beam assist
This feature allows high beam to
function as the main driving light at
night and when vehicle speed is
faster than 25 mph.
To activate, push the lever
forwards twice at a speed above
25 mph.
The green control indicator l
illuminates continuously when high
beam assist is activated, the blue
one 7 illuminates when high beam
is on.
Hazard warning flashers:
Operated with the ¨ button.
In the event of an accident where
the airbags are deployed, the
hazard warning flashers are
activated automatically.
Heated rear window, heated
exterior mirrors:
The heating is operated by
pressing the Ü button. The LED in
the button indicates activation.
Heating functions with the engine
running and switches off
automatically after a short time.
Heated rear window is deactivated
when the soft top is opened.
Demisting and defrosting the
windows:
Press button V.
Fan automatically switches to
higher speed and air is directed
towards the windscreen.
Set the temperature control to the
highest level.
Switch cooling n on.
Switch heated rear window Ü on.
Open side air vents and direct them
towards the door windows.
Seat position:
Sit with buttocks as far back
against backrest as possible.
Adjust distance between seat and
pedals so that legs are slightly
angled when depressing pedals.
Slide the front passenger seat as
far back as possible.
Steering wheel adjustment:
Unlock the lever, adjust the
steering wheel, then engage the
lever and ensure it is fully locked.
Adjust only when vehicle is
stationary and steering wheel lock
is released.
Seat inclination:
Lever pumping motion.
up = front end higher
down = front end lower
Interior mirror:
Swivel mirror housing to adjust.
To reduce dazzle, adjust the lever
on the underside of the mirror
housing.
4-window switch:
Central switch in the centre console
is used to operate all windows.
Push switch , briefly to open all
windows automatically.
Pull switch , briefly to close all
windows automatically.
Safety function:
If the window glass encounters
resistance above the middle of the
window during automatic closing,
it is immediately stopped and
opened again.
Operating windows and soft top
with remote control:
The windows and the soft top can
be operated remotely from outside
the vehicle.
Press button c once briefly: the
doors are unlocked.
Press button c again for
two seconds: the windows open
automatically.
Hold button c pressed after
unlocking: the soft top will be
opened. Hold button c pressed
until soft top is completely opened.
Release button c during opening of
the soft top: movement stops for
10 seconds; press button c again
to continue opening the soft top.
Power windows:
Switch on ignition to operate.
Front switches operate the front
windows and rear switches operate
the rear windows.
„ Push switch = Open window
„ Pull switch = Close window
Push or pull switch gently to the first
detent position: Window moves up
or down as long as the switch is
operated.
Push or pull switch to the second
detent position and then release:
Window opens or closes
automatically. Operate the switch
again to stop window movement.
If the window glass encounters
resistance above the middle of the
window during automatic closing,
it is immediately stopped and
opened again.
Windscreen wiper:
2 = Fast
1 = Slow
P = Timed interval wiping
or automatic wiping with
rain sensor
§ = Off
For a single wipe when the
windscreen wiper is off, press the
lever down.
Vehicles with adjustable wiper
interval: With wiper lever in
position P, turn adjuster wheel
upwards or downwards to make
wiping interval shorter or longer.
Do not use if the windscreen is
frozen.
Switch off in car washes.

Question & answers

There are no questions about the Vauxhall Cascada (2013) yet.

Ask a question about the Vauxhall Cascada (2013)

Have a question about the Vauxhall Cascada (2013) but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Vauxhall Cascada (2013). Please make sure that you describe your difficulty with the Vauxhall Cascada (2013) as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.