ULGD 3.8 A1

Ultimate Speed ULGD 3.8 A1 manual

ULGD 3.8 A1

User manual for the Ultimate Speed ULGD 3.8 A1 in Dutch. This PDF manual has 59 pages.

Page: 1
1 ULGD 3.8 A1 GB IE Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Parts description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Connecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Measuring STANDBY / Battery voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Revitalising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Program selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Program 1 „6 V“ (7,3 V / 0,8 A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Program 2 „12 V“ (14,4 V / 0,8 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Program 3 „12 V“ (14,4 V / 3,8 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Program 4 „12 V“ (14,7 V / 3,8 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Retention charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Appliance protection function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Translation of the original Conformity Declaration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Page: 2
2 ULGD 3.8 A1 GB IE CAR BATTERY CHARGER ULGD 3.8 A1 Introduction We congratulate you on the purchase of your new device. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the unit as described and for the specified applica- tions. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it. Intended use The Ultimate Speed ULGD 3.8 A1 is a multi-stage car battery charger that is suitable for charging and trickle charging up of 6 V or 12 V lead-acid batteries (batteries) with electrolyte solution (WET), electrolyte absorbent mats (AGM) or gel electrolyte (GEL). This appliance is not suitable for charging lithium-ion batteries. The is not intended for commercial use and is for indoor use only. The manufacturer accepts no responsibility for damage(s) arising out of usage contrary to the instructions specified below. Scope of delivery 1 Car battery charger ULGD 3.8 A1 2 Clamps (1 red, 1 black) 1 Instructions for use Parts description See Figure A: 12 V / 0.8 A (Program 2) 12 V / 3.8 A (Program 3) 12 V / 3.8 A (Program 4) 6 V / 0.8 A (Program 1) LED reverse connection LED stand-by Charge display Condition display Voltage display Program selection button (MODE) See Figure B: Charger Fastening eyelets Mains lead Positive pole clamp (red) Negative pole clamp (black) Positive pole connector cable (red) inc. lug Negative pole connector cable (black) inc. lug Technical Data Input voltage: 220-240 V ∼ 50/60 Hz Power consumption: 60 W Output voltage: 6 V /12 V Output power: 0.8 A/3.8 A Fuse (internal): 2 A T2A Environmental temperature: 0°C bis 40°C Protection rating: IP 65 Protection class: II/ Battery types: 6 V lead acid battery 1.2 Ah-14 Ah 12 V Lead acid battery 1.2 Ah-120 Ah Safety Safety instructions This charger is suitable for indoor use only. ■ This appliance may be used by children aged 8 over and by persons with reduced physical, sensory or mental capabilities or lack of experi- ence and knowledge, provided that they are under supervision or have been told how to use the appliance safely and are aware of the poten- tial risks. Children must not use the appliance as a plaything. Cleaning and user maintenance tasks may not be carried out by children unless they are supervised.
Page: 3
3 ULGD 3.8 A1 GB IE ■ Do not use the charger for charging non- rechargeable batteries. ■ Do not use the charger for charging lithium-ion batteries. ■ Place the removed battery in a well-ventilated location during charging. ■ The automatic mode of operation and usage restrictions are explained below in these operat- ing instructions. DANGER OF ELECTRIC SHOCK! ■ Do not operate the appliance with a damaged cable, supply cord or mains plug. A damaged power cord causes danger to life by electric shock. ■ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. ■ Before connecting to the power, ensure that the power connection is earthed, is 230 V ∼ 50 Hz, and is 16 A fused and equipped with an RCCB switch (residual current circuit breaker) in accordance with the current regulations! ■ Disconnect the charger from the grid, before you make or break connections to the battery. ■ First, connect the clamp that is not connected to the bodywork. Then connect the other clamp to the bodywork, away from battery and fuel pipe. Only after this, connect the charger to the grid. ■ After charging, disconnect the charger from the grid. Only after this remove the clamp from the bodywork. Following this, remove the clamp from the battery. DANGER OF EXPLOSION AND FIRE HAZARD! Protect yourself from a highly explosive hydrogen- oxygen reaction! ■ Ensure that during charge and charge retention procedures, there are no naked lights (flames, cinders or sparks)! ■ Ensure that the plus cable does not come into contact with fuel lines (e.g. petrol pipe)! ■ Ensure that there is no possibility of ignition of ex- plosive or flammable substances, such as petrol or solvents, while using charger! ■ Ensure that there is adequate ventilation during charging. DANGER OF CHEMICAL BURNS! ■ Wear protective glasses! Wear protective gloves! If eyes or skin has come into contact with battery acid, rinse the affected body region off with a large amount of clean water and consult a doc- tor straight away! ■ Avoid causing a short circuit when connecting the charger to the battery. Connect the negative pole connector cable only to the negative bat- tery or to the body work. Connect the positive pole connector cable only to the plus pole of the battery! ■ Do not place the charger close to fire, heat or to places with long-term exposure to tempera- tures over 50 °C! ■ Ensure that no fuel lines,electric cables, hydrau- lic or water pipes are damaged by the screws during assembly of the charger! ■ Do not cover the charger with any objects! ■ Protect the electrical contact surfaces of the bat- tery from short circuiting! ■ Only use the charger for charging and for charge retention of 6 V / 12 V lead batteries. Do not charge frozen batteries.
Page: 4
4 ULGD 3.8 A1 GB IE Operation Before use ♦ Before connecting the charger, the operating instructions must be observed. ♦ Furthermore, the instructions of the vehicle man- ufacturer regarding a permanently connected vehicle battery must be observed. Secure the vehicle, switch off the ignition. ♦ Clean the battery poles. Take care that while doing so, your eyes do not come into contact with the dirt. ♦ Ensure sufficient ventilation. Connecting ♦ Before starting the charging or trickle charging procedure on a permanently installed battery in a vehicle, first disconnect the negative terminal connecting cable (black) of the vehicle from the negative terminal of the battery. The negative terminal of the battery is usually connected to the vehicle’s coachwork. ♦ Connect the positive pole clamp (red) of the charger to the positive pole of the battery. ♦ Connect the negative pole clamp (black) to the negative pole of the battery. ♦ Connect the mains cable of the charger to the mains socket. ♦ The battery voltage display shows the cur- rent battery voltage. ♦ Should the connection of the clamps be swapped, the LED „reverse connection“ lights up. Disconnect ♦ Disconnect the appliance from the mains supply. ♦ Remove the negative pole clamp (black) from the negative pole of the battery. ♦ Remove the positive pole clamp (red) from the positive pole of the battery. Measuring STANDBY / Battery voltage After connection to the grid, the appliance is on STANDBY. The standby display lights up. When the clamps are connected, the battery voltage is shown in the LCD (voltage display ). The segments of the condition display are empty. If the voltage is below 3.8 V or above 15 V, the battery will not be charged. The display briefly shows the error message „Err“. The appliance goes on standby. 6 V battery: If the voltage range of the battery is measured as between 3.7–7.3 V, only program 1 can be selected. 12 V batteries: If a battery is recognised in the critical voltage range of between 7.3–10.5 V, the appliance checks whether a fully charged 6 V battery, or a discharged 12 V battery is present. After pressing the program selection button to select a program, the appliance carries out a control measurement for about 90 sec. The display shows: If after about 90 sec. between 7.3–7.5 V are detected, the 12 V battery is defective. The appliance goes on standby. Revitalising If after about 90 sec. between 7.5–10.5 V are detected, a 12 V battery is present. Charging starts with a pulse charge for revitalis- ing. The voltage display flashes. Once 10.5 V are reached, the appliance switches to the other charge steps. Revitalising is the same for all the 12 V charge programmes.
Page: 5
5 ULGD 3.8 A1 GB IE Program selection NOTES ► If a battery is detected in the voltage range of between 3.7–7.3 V, the programmes 2–3–4 can be selected. The charging process takes place automatically. Depending on the selected program, the characteristic charge curve is monitored for voltage, time and temperature. Included are the diagnostics program, revitalis- ing mode and retention charge. (See principle representation program 3 Fig. C) Program max. (V) max. (A) 1 6 V 7,3 V 0,8 A 2 * 14,4 V 0,8 A 3 * 14,4 V 3,8 A 4 * 14,7 V 3,8 A Program 1 „6 V“ (7,3 V / 0,8 A) For charging 6 V batteries with a capacity of less than 14 Ah. ♦ Press the program selection button , to select program 1. The symbol „6 V“ is displayed on the LCD. During charging, the charge display flashes and shows the progress of the charge procedure (1–4 bars). When the battery is fully charged, the condition display shows 4 bars. The flashing stops and the appliance automati- cally switches to retention charge. Program 2 „12 V“ (14,4 V / 0,8 A) For charging 12 V batteries with a capacity of less than 14 Ah. ♦ Press the program selection button , to select program 2. The symbol is displayed on the LCD. During charging, the charge display flashes and shows the progress of the charge procedure (1–4 bars). When the battery is fully charged, the condition display shows 4 bars. The flashing stops and the appliance automati- cally switches to retention charge. Program 3 „12 V“ (14,4 V / 3,8 A) For charging 12 V batteries with a capacity of between 14 Ah–120 Ah. ♦ Press the program selection button , to select program 3. The symbol is displayed on the LCD. During charging, the charge display flashes and shows the progress of the charge procedure (1–4 bars). When the battery is fully charged, the condition display shows 4 bars. The flashing stops and the appliance automatically switches to retention charge. Program 4 „12 V“ (14,7 V / 3,8 A) For charging 12 V batteries with a capacity of between 14 Ah–120 Ah under cold conditions or for charging AGM batteries. ♦ Press the program selection button , to select program 4. NOTE ► This program may start with a minute delay. The symbol is displayed on the LCD. During charging, the charge display flashes and shows the progress of the charge procedure (1–4 bars). When the battery is fully charged, the condition display shows 4 bars. The flashing stops and the appliance automatically switches to retention charge. Retention charge As described under programmes, this appliance features the automatic retention charge. Depending on the voltage drop of the battery, caused by selfdischarge, the appliance reacts with different charge currents. The battery can remain connected to the charger for longer periods of time. Appliance protection function The charger switches the electronics off and switches the system instantly to the basic setting, as soon as there is an abnormal situation, such as short circuit, critical voltage drop during charging, broken circuit or swapped connection of the connector clamps is detected. Should the appliance become too hot during charg- ing, the output current is automatically reduced. This protects the appliance from damage.
Page: 6
6 ULGD 3.8 A1 GB IE Maintenance and care WARNING! Before you carry out any work on the battery charger always pull the mains plug out of the mains socket. The appliance is maintenance-free. ♦ Do not under any circumstances use solvents or other aggressive cleaning agents. ♦ Clean the plastic surfaces of the device with a dry cloth. Warranty The warranty for this appliance is for 3 years from the date of purchase. The appliance has been manufactured with care and meticulously examined before delivery. Please retain your receipt as proof of purchase. In the event of a warranty claim, please make contact by telephone with our Service Department. Only in this way can a post-free despatch for your goods be assured. The warranty covers only claims for material and manufacturing defects, but not for transport dam- age, for wearing parts or for damage to fragile components, e.g. buttons or batteries. This product is for private use only and is not intended for com- mercial use. The warranty is void in the case of abusive and improper handling, use of force and internal tampering not carried out by our author- ized service branch. Your statutory rights are not restricted in any way by this warranty. The warranty period will not be extended by repairs made under warranty. This applies also to replaced and repaired parts. Any damage and defects extant on purchase must be reported immediately after unpacking the appliance, at the latest, two days after the purchase date. Repairs made after the expiration of the war- ranty period are subject to payment. Service Service Great Britain Tel.: 0871 5000 720 (£ 0.10/Min.) E-Mail: kompernass@lidl.co.uk IAN 102626 Service Ireland Tel.: 1890 930 034 (0,08 EUR/Min., (peak)) (0,06 EUR/Min., (off peak)) E-Mail: kompernass@lidl.ie IAN 102626 Hotline availability: Monday to Friday 08:00 - 20:00 (CET) Importer KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com Disposal The packaging is made from environ- mentally friendly material and can be disposed of at your local recycling plant. Do not dispose of power tools in your normal domestic waste! European Directive 2012/19/EU requires that worn-out power tools are collected separately and fed into an environmentally compatible recycling process. Your local community or municipal authorities can provide information on how to dispose of the worn-out appliance.
Page: 7
7 ULGD 3.8 A1 GB IE Translation of the original Conformity Declaration We, KOMPERNASS HANDELS GMBH, Custodian of Documents: Mr. Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents and the EC directives: EU Low Voltage Regulations (2006/95/EC) EMC (Electromagnetic Compatibility) (2004/108/EC) RoHS Directive (2011/65/EU) Related harmonised standards: EN 60335-2-29/A2:2010 EN 60335-1:2012 EN 62233:2008 EN 55014-1:2006+A1:2009+A2:2011 EN 55014-2:1997+A1:2001+A2:2008 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2013 Type designation of machine: Car battery charger ULGD 3.8 A1 Year of manufacture: 09-2014 Serial number: IAN 102626 Bochum, 05/03/2014 Semi Uguzlu - Quality Manager - Subject to technical changes in the course of further developments.
Page: 8
IAN 102626 KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM DEUTSCHLAND/GERMANY www.kompernass.com Last Information Update · Tietojen tila · Informationsstatus Tilstand af information · Version des informations Stand van de informatie · Stand der Informationen: 07/2014 · Ident.-No.: ULGD3.8A1-062014-2

Question & answers

Have a question about the Ultimate Speed ULGD 3.8 A1 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Ultimate Speed ULGD 3.8 A1. Please make sure that you describe your difficulty with the Ultimate Speed ULGD 3.8 A1 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Ultimate Speed ULGD 3.8 A1

Name
Email
Reaction

View a manual of the Ultimate Speed ULGD 3.8 A1 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Ultimate Speed
  • Product: Chargers
  • Model/name: ULGD 3.8 A1
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Swedish, Danish, Norwegian, Finnish, Italian