View a manual of the Sony CDP-CE245 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
4-226-518-21 (2) 2000 Sony Corporation CDP-CE345 CDP-CE245 Compact Disc Player Operating Instructions Mode d’emploi Manual de instrucciones GB FR ES
2GB WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. About This Manual The instructions in this manual are for models CDP-CE345 and CDP-CE245. The CDP-CE345 is the model used for illustration purposes, unless otherwise mentioned. Any difference in operation is clearly indicated in the text, for example, “CDP-CE345 only.” Conventions • Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player. • The following icons are used in this manual: Z Indicates that you can do the task using the remote. (Note that the CDP-CE245 cannot do the tasks marked with this icon.) z Indicates hints and tips for making the task easier. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. Welcome! Thank you for purchasing the Sony Compact Disc Player. Before operating the unit, please read this manual thoroughly and retain it for future reference. The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
3GB GB TABLE OF CONTENTS Getting Started Unpacking............................................................................................................................. 4 Hooking Up the System ...................................................................................................... 4 Playing a CD ............................................................................................................................. 6 Playing CDs Using the Display ................................................................................................................ 8 Replacing Discs While Playing a Disc .............................................................................. 9 Locating a Specific Disc ...................................................................................................... 9 Locating a Specific Track or a Particular Point in a Track ........................................... 10 Playing Repeatedly ............................................................................................................ 11 Playing in Random Order (Shuffle Play) ....................................................................... 11 Creating Your Own Program (Program Play) ............................................................... 12 Recording From CDs Recording Your Own Program ........................................................................................ 14 Recording a CD by Specifying Tape Length (Time Edit)............................................. 14 Fading In or Out................................................................................................................. 15 Adjusting the Recording Level (Peak Search) ............................................................... 16 Additional Information Precautions ......................................................................................................................... 17 Notes on CDs ...................................................................................................................... 17 Troubleshooting ................................................................................................................. 18 Specifications ...................................................................................................................... 18 Index Index .................................................................................................................................... 19
Getting Started 4GB Unpacking Check that you received the following items: • Audio connecting cord (1) • Remote commander (remote) (1) (CDP-CE345 only) • Size AA (R6) batteries (2) (CDP-CE345 only) Inserting batteries into the remote (CDP- CE345 only) You can control the player using the supplied remote. Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. When using the remote, point it at the remote sensor on the player. Hooking Up the System Overview This section describes how to hook up the CD player to an amplifier. Be sure to turn off the power of each component before making the connections. CD player Amplifier : Signal flow White (L) Red (R) White (L) Red (R) What cords will I need? Audio cord (supplied) (1) ANALOG OUT (L) ANALOG OUT (R) Audio input (L) Audio input (R) To an AC outlet To an AC outlet z When to replace batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Getting Started DIGITAL OUT (OPTICAL)
Getting Started Getting Started 5GB Hookups When connecting an audio cord, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise. Amplifier CD player z You can adjust the output level to the amplifier (CDP- CE345 only) Z Press ANALOG OUT LEVEL +/– on the remote. You can reduce the output level up to –20 dB. When you reduce the output level, “FADE” appears in the display. When you turn off the player, the output level automatically returns to the maximum level. Note If you press the ANALOG OUT LEVEL +/– buttons on the remote while recording, the recording level will change even when it is preset on the tape deck, etc. • If you have a digital component such as a digital amplifier, D/A converter, DAT or MD Connect the component via the DIGITAL OUT (OPTICAL) connector using the optical cable (not supplied). Take off the cap and plug in the optical cable. Note that you cannot use fading in or out (page 15) and Time Fade (page 15) functions when making this connection. Connecting the AC power cord Connect the AC power cord to a wall outlet. Transporting the player Before transporting the player, follow the procedure below to return the internal mechanisms back to their original position. 1 Remove all the discs from the disc tray. 2 Press A OPEN/CLOSE to close the disc tray. “no dISC” appears in the display. 3 Wait for 10 seconds, then press POWER to turn off the player. POC-15 Optical cable (not supplied) Note When you connect via the DIGITAL OUT (OPTICAL) connector, noise may occur when you play CD software other than music, such as a CD-ROM. Digital component CD player Setting the voltage selector (voltage selector equipped models only) Check that the voltage selector on the rear panel of the player is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to a wall outlet. INPUT CD L R L R ANALOG OUT DIGITAL OUT OPTICAL DIGITAL INPUT OPTICAL 110 - 120 V 220 - 240 V
Basic Operations 6GB 2 3 Playing a CD 2 4 5 • See pages 4 - 5 for the hookup information. The player plays All discs in the player consecutively in the order of disc number Only the disc you’ve selected 4 3 6 5 Turn on the amplifier and select the CD player position so that you can listen to the sound from this player. Press POWER to turn on the player. Press A OPEN/CLOSE, and place a disc on the disc tray. To place other discs, press DISC SKIP and place the discs in the order you want to play. Each time you press the button, the disc tray turns and you can place the discs in the empty disc compartments. The player plays the disc in front of you first. Press CONTINUE to select ALL DISCS or 1 DISC Continuous Play mode. Each time you press the CONTINUE button, “ALL DISCS” or “1 DISC” appears in the display. When you select ALL DISCS 1 DISC CONTINUE AMS PUSH ENTER SHUFFLE PROGRAM DISC 1 POWER DISC 2 DISC 3 DISC 4 DISC 5 REPEAT TIME EX- CHANGE DISC SKIP MUSIC SCAN FADER CHECK CLEAR SEARCH TIME FADE PEAK EDIT/ OPEN/CLOSE 1 With the label side up Disc number
Basic Operations Basic Operations 7GB 6 Press H. The disc tray closes and the player plays all the tracks once (Continuous Play). Adjust the volume on the amplifier. z You can select the disc you want to start playing first Press one of the DISC 1 - 5 buttons. z You can adjust the output level to the amplifier (CDP- CE345 only) Z Press ANALOG OUT LEVEL +/– on the remote. You can reduce the output level up to –20 dB. When you reduce the output level, “FADE” appears in the display. When you turn off the player, the output level automatically returns to the maximum level. Note If you press the ANALOG OUT LEVEL +/– buttons on the remote while recording, the recording level will change even when it is preset on the tape deck, etc. To stop playback Press x. To Pause Resume play after pause Go to the next track Go back to the preceding track Go to the next disc Select a disc directly Stop play and remove the CD You need to Press X Press X or H Turn l AMS L clockwise Turn l AMS L counterclockwise Press DISC SKIP Press DISC 1 - 5 Press A OPEN/CLOSE DISC 1 - 5 H X x DISC SKIP A OPEN/CLOSE l AMS L POWER CONTINUE AMS PUSH ENTER SHUFFLE PROGRAM DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 REPEAT TIME EX- CHANGE DISC SKIP MUSIC SCAN FADER CHECK CLEAR SEARCH TIME FADE PEAK EDIT/ OPEN/CLOSE
Playing CDs 8GB 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 DISCS ALL TRACK DISC MIN SEC 1 1 1 56 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 DISCS ALL TRACK DISC MIN SEC 1 1 -1 57 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 DISCS ALL TRACK DISC MIN SEC 1 1-43 32 Using the Display You can check information about the disc using the display. Playing CDs Display information while playing a disc While playing a disc, the display shows the current disc number, track number, playing time of the track and the music calendar. Current disc number Music calendar Current track number Playing time The track numbers in the music calendar disappear after they are played. Checking the remaining time Each time you press the TIME button while playing a disc, the display changes as shown in the chart below. Playing time and number of the current track Press TIME. Remaining time on the current track If the track number exceeds 24, “– – . – –” appears instead of the remaining time. Press TIME. Remaining time on the disc This information is available only in Continuous Play mode. Press TIME. TIME Checking the total number and playing time of the tracks Press TIME before you start playing. The display shows the current disc number, the total number of tracks, total playing time and music calendar. The information also appears when you press the A OPEN/CLOSE button to close the disc tray. The tracks numbered over 20 cannot be displayed in the music calendar. Notes on the disc number indications • The red circle around a disc number indicates the disc is ready to be played. • When all the tracks on a disc have been played, the semi- circle around the disc number disappears. • When a disc compartment is recognized as empty, the semi- circled disc number disappears. Total number of tracks Music calendar Total playing time Current disc number 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 DISCS ALL TRACK DISC MIN SEC 1 10 45 28 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 DISCS ALL TRACK DISC MIN SEC 1 1 1 56
Playing CDs Playing CDs 9GB DISC SKIP 1 Press EX-CHANGE. The disc tray opens and two disc compartments appear. Even if the player is playing a disc, it doesn’t stop playing. 2 Replace discs in the compartments with new ones. The player plays the disc on the left side compartment after the current disc, and then the one on the right side compartment. 3 Press DISC SKIP. The disc tray turns and other two disc compartments appear. 4 Replace discs in the compartments with new ones. 5 Press EX-CHANGE. The disc tray closes. While the disc tray is open by pressing the EX-CHANGE button • If the playback of the current disc ends, the player stops playing. If the disc is played in 1 DISC Repeat Play mode (see page 11), the current disc starts playing again. • In ALL DISCS Shuffle Play mode (see page 11), tracks are reshuffled on the current disc. • In Program Play mode (see page 12), only the tracks on the current disc are played. • Do not push the disc tray to close it in Step 5, as you may damage the player. Replacing Discs While Playing a Disc You can open the disc tray while playing a disc so that you can check what discs are to be played next and replace discs without interrupting playback of the current disc. To locate The next disc A specific disc directly Press DISC SKIP while playing a disc DISC 1 - 5 EX-CHANGE DISC 1 - 5 DISC SKIP Locating a Specific Disc You can locate any disc before or while playing a disc.
Playing CDs 10GB Locating a Specific Track or a Particular Point in a Track You can quickly locate any track while playing a disc using the AMS (Automatic Music Sensor) control. You can also locate a specific point in a track while playing a disc. z You can extend the playing time during Music Scan Press MUSIC SCAN repeatedly until the playing time you want (10, 20 or 30) appears in the display. Each time you press the button, the playing time changes cyclically. Note If “ ” appears in the display, the disc has reached the end while you were pressing the M button. Press m or turn l AMS L counterclockwise to go back. l AMS L H MUSIC SCAN m/M To locate The next or succeeding tracks The current or preceding tracks A track by scanning each track for 10 seconds (Music Scan) A point while monitoring the sound A point quickly by observing the display during pause You need to Turn l AMS L clockwise until you find the track. When using the remote, press > repeatedly until you find the track. Turn l AMS L counterclockwise until you find the track. When using the remote, press . repeatedly until you find the track. Press MUSIC SCAN before you start playing. When you find the track you want, press H to start playing. Press M (forward) or m (backward) and hold down until you find the point. Press M (forward) or m (backward) and hold down until you find the point. You will not hear the sound during the operation.
Playing CDs Playing CDs 11GB Playing in Random Order (Shuffle Play) You can have the player “shuffle” tracks and play in a random order. The player shuffles all the tracks on all discs or on the disc you’ve specified. Playing Repeatedly You can play discs/tracks repeatedly in any play mode. Press REPEAT while playing a disc. “REPEAT” appears in the display. The player repeats the discs/tracks as follows: When the disc is played in Continuous Play (ALL DISCS) (page 6) Continuous Play (1 DISC) (page 6) Shuffle Play (ALL DISCS) (page 11) Shuffle Play (1 DISC) (page 12) Program Play (page 12) To cancel Repeat Play Press REPEAT repeatedly until “REPEAT” disappears from the display. Repeating the current track You can repeat only the current track while the disc is played in any play mode. While the track you want is being played, press REPEAT repeatedly until “REPEAT 1” appears in the display. The player repeats All the tracks on all discs All the tracks on the current disc All the tracks on all discs in random orders All the tracks on the current disc in random orders The same program DISC 1 - 5 SHUFFLE Shuffle Play on all discs You can play all tracks on all discs in a random order. 1 Press SHUFFLE repeatedly until “ALL DISCS” appears in the display. 2 Press H to start ALL DISCS Shuffle Play. The indication appears while the player is “shuffling” the tracks. To cancel Shuffle Play Press CONTINUE. z You can start Shuffle Play while playing Press SHUFFLE, and Shuffle Play starts from the current track. z You can specify discs during Shuffle Play (Select Shuffle Play) You can specify discs during ALL DISCS Shuffle Play mode, and the tracks on the specified discs are played in a random order. Press DISC 1 - 5 to specify the discs after Step 1. Semi-circles appear around the specified disc numbers in the display. To cancel the selected discs, press DISC 1 - 5 again. The semi-circles disappear. To return to ALL DISCS Shuffle Play, press SHUFFLE twice. REPEAT H
Playing CDs 12GB Shuffle Play on one disc You can play all tracks on the specific disc in a random order. 1 Press SHUFFLE repeatedly until “1 DISC” appears in the display. 2 Press DISC 1 - 5 to start 1 DISC Shuffle Play on the selected disc. The indication appears while the player is “shuffling” the tracks. To cancel Shuffle Play Press CONTINUE. z You can start Shuffle Play while playing Press SHUFFLE, and Shuffle Play starts from the current track. Creating Your Own Program (Program Play) You can arrange the order of the tracks on the discs and create your own program. The program can contain up to 32 “steps” — one “step” may contain a track or a whole disc. CLEAR CHECK 1 Press PROGRAM. “PROGRAM” appears in the display. If a program is already stored, the last step of the program appears in the display. When you want to erase the whole program, hold down CLEAR until “ALL CLr” appears in the display (see page 13). 2 Press DISC 1 - 5 to select the disc. “AL” in the display stands for “all” tracks. When you want to program the whole disc as one step, skip Steps 3 to 4, and go to Step 5. 3 Turn l AMS L until the track number you want appears in the display. The track number being programmed flashes and the total playing time including the track appears in the display. Total playing time Track number being programmed l AMS L H DISC 1 - 5 2 5 8 1 2 3 4 5 PROGRAM TRACK DISC MIN SEC A 1 5 13 18 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 PROGRAM TRACK DISC MIN SEC A 1 AL 42 11 PROGRAM
Playing CDs Playing CDs 13GB 2 5 8 1 2 3 4 5 PROGRAM TRACK DISC STEP A 1 5 3 2 5 8 1 2 3 4 5 PROGRAM TRACK DISC MIN SEC A 1 5 13 18 4 Push l AMS L to select the track. If you’ve made a mistake Press CLEAR, then repeat Steps 3 and 4. 5 To program other discs or tracks, do the following: To program Other discs Other tracks on the same disc Other tracks on other discs 6 Press H to start Program Play. To cancel Program Play Press CONTINUE. The program remains in memory even if you stop the Program Play. z You can create your program while checking the disc labels While the disc tray is open, follow Steps 1 to 6 with pressing the DISC SKIP button to check the disc labels. If you close the disc tray before Step 6, the total playing time appears in the display after a while. Note that, if the programmed track number isn’t found on the disc, that step is automatically erased. z The program remains even after the Program Play ends When you press the H button, you can play the same program again. After one second Total playing time Programmed tracks Repeat Step(s) 2 3 and 4 2 through 4 z The program remains until you erase it or turn off the player If you replace discs, the programmed disc and track numbers remain. So, the player plays only the existing disc and track numbers. However, the disc and track numbers that aren’t found in the player or on the disc are deleted from the program, and the rest of the program is played in the programmed order. Note The total playing time doesn’t appear when: —You have programmed a track whose number exceeds 20. —The total playing time of the program exceeds 200 minutes. Checking the track order You can check your program before or after you start playing. Press CHECK. Each time you press this button, the display shows the track (the disc and track numbers) or the disc (the disc number and “AL” indication) of each step in the programmed order. After the last step in the program, the display shows “End” and returns to the original display. If you check the order after you start playing, the display shows only the remaining steps. Changing the track order You can change your program before you start playing. To Erase a track Erase the last track in the program Add tracks to the end of the program Change the whole program completely You need to Press CHECK until the track you don’t want appears in the display, then press CLEAR. Press CLEAR. Each time you press the button, the last track will be cleared. Follow Steps 2 through 4 of the programming procedure. Hold down CLEAR until “ALL CLr” appears in the display. Create a new program following the programming procedure. Last programmed track Playing order
Recording From CDs 14GB Recording From CDs Recording Your Own Program You can record the program you’ve created on a tape, etc. The program can contain up to 32 steps. By inserting a pause during programming, you can divide the program into two for recording on both sides of a tape. 1 Create your program (for side A when recording on a tape) while checking the total playing time indicated in the display. Follow Steps 1 to 5 in “Creating Your Own Program” on page 12. The A indication appears in the display. 2 When you record on both sides of the tape, press X to insert a pause. The “P” and A B indications appear in the display and the playing time is reset to “0.00.” When you record on one side of the tape, skip this step and go to Step 4. A pause is counted as one step You can program up to 31 steps when you insert a pause. 3 Repeat Steps 2 to 5 in “Creating Your Own Program” on page 12 to create the program for side B. 4 Start recording on the deck and then press H on the player. Whenyourecordonbothsidesofthetape,theplayer pauses at the end of the program for side A. 5 When you record on side B, reverse the tape and press H or X on the player to resume playing. z To check and change your program See page 13. The A indication appears while checking the program for side A and B while checking the program for side B. Recording a CD by Specifying Tape Length (Time Edit) You can have the player create a program that will fit the length of the tape. The player automatically creates a program, keeping the original order of the disc. The program can contain up to 32 steps (a pause inserted between steps is counted as one step). Note that tracks numbered over 20 cannot be programmed automatically. 1 Press DISC SKIP to select the disc. 2 Press EDIT/TIME FADE repeatedly before you start playing until “EDIT” appears and “A” in the A indication flashes in the display. 3 Press m or M to specify the tape length. Each time you press these buttons, the display changes as shown below, with the tape length of one side following each indication. t C-46 y C-54 y C-60 y C-74 y C-90 y - -. - - T (23.00) (27.00) (30.00) (37.00) (45.00) 4 Press EDIT/TIME FADE to have the player create the program. The display shows the tracks to be recorded. “B” in the A B indication flashes in the display. 5 When you record on both sides of the tape, press EDIT/TIME FADE again. The player inserts a pause, then creates the program for side B. The display shows the programmed tracks. When you record on one side of the tape, skip this step. 6 Start recording on the deck and then press H on the player. When you record on both sides of the tape, the player pauses at the end of the program for side A. PROGRAM l AMS L H X DISC 1 - 5 m/M EDIT/TIME FADE DISC SKIP H X
Recording From CDs 15GB Recording From CDs Recording From CDs Recording From CDs 7 Reverse the tape to side B and press H or X on the player to resume playing the remaining tracks. To cancel Time Edit Press CONTINUE. z You can program the tracks you want in advance Create a program selecting the desired tracks, then follow Steps 2 to 7. Be careful that the total playing time of the program does not exceed the tape length of one side. z You can freely specify the tape length Set the tape length using the l AMS L control. Example: When the tape length of one side is 30 minutes and 15 seconds 1 To set the minutes, turn l AMS L until “30” appears in the display, then push l AMS L. 2 To set the seconds, turn l AMS L until “15” appears in the display, then push l AMS L. z You can check and change the program See page 13. Fading In or Out You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector. To Start play fading in End play fading out Note Fading lasts for about 5 seconds. However, when you press the FADER button during Music Scan (see page 10), the play fades out for about 2 seconds. Fading out at the specified time (Time Fade) You can have the player fade out automatically by specifying the playing time. Once you set the Time Fade, it works twice, that is, the play fades out at the end of both sides of a tape. 1 Press EDIT/TIME FADE repeatedly before you start playing until TIME FADE and A appear in the display. 2 Press m or M to specify the playing time. Each time you press these buttons, the display changes as shown below, with the playing time of one side following each indication. t C-46 y C-54 y C-60 y C-74 y C-90 y - -. - - T (23.00) (27.00) (30.00) (37.00) (45.00) EDIT/TIME FADE m/M FADER X H (Continued) Press FADER During pause. “FADE” flashes, then the play fades in. When you want to start fading out. “FADE” flashes and the play fades out. Then the player pauses.
Recording From CDs 16GB 3 Press H to start playing. At the specified time the play fades out and the player pauses. B appears in the display. 4 Reverse the tape to side B and press H or X on the player to resume playing the remaining tracks. Again, the play fades out at the specified time. To cancel Time Fade Press EDIT/TIME FADE. z You can freely specify the playing time See “You can freely specify the tape length” on page 15. z You can change discs during Time Fade If the play ends before the specified fade-out time, (for example, when you record CD-singles on a tape) change the disc. The specified fade-out time is counted only during playing. z You can fade in to resume playing in Step 4 After you reverse the tape, press FADER. Note If you press the m or M button during Time Fade Play, Time Fade will be cancelled. Adjusting the Recording Level (Peak Search) The player locates the highest level among the tracks to be recorded to let you adjust the recording level before you start recording. PEAK SEARCH x 1 Before you start playing, press PEAK SEARCH. “PEAK” flashes in the display and the player starts scanning the disc searching for the highest peak level. After scanning all the tracks, the player repeats the portion with the highest peak level. 2 Adjust the recording level on the deck. 3 Press x on the player to stop Peak Search. “PEAK” disappears from the display. Notes • The portion with the highest level may differ every time you try the adjustment on the same disc. The difference is, however, so slight that you won’t find any problem in adjusting the recording level precisely. • Peak Search does not operate while you open the disc tray by pressing the EX-CHANGE button.
Additional Information Additional Information 17GB Additional Information Notes on CDs On handling CDs • To keep the disc clean, handle the disc by its edge. Do not touch the surface. • Do not stick paper or tape on the disc. • Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be considerable rise in temperature inside the car. • Do not use any commercially available stabilizer. If you do, the disc and the player may be damaged. • After playing, store the disc in its case. On cleaning • Before playing, clean the disc with a cleaning cloth. Wipe the disc from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. Precautions On safety • Caution — The use of optical instruments with this product will increase eye hazard. • Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further. On power sources • Before operating the player, check that the operating voltage of the player is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the player. • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. • AC power cord must be changed only at the qualified service shop. On placement • Place the player in a location with adequate ventilation to prevent heat build-up in the player. • Do not place the player on a soft surface such as a rug that might block the ventilation holes on the bottom. • Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about an hour until the moisture evaporates. On adjusting volume • Do not turn up the volume while listening to a portion with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level portion is played. On cleaning • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any questions or problems concerning your player, please consult your nearest Sony dealer.
Additional Information 18GB Troubleshooting If you experience any of the following difficulties while using the player, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. There’s no sound. , Check that the player is connected securely. , Make sure you operate the amplifier correctly. , Adjust the playback level using the ANALOG OUT LEVEL +/– buttons on the remote (CDP- CE345 only). The CD does not play. , There’s no CD inside the player (“no dISC” appears). Insert a CD. , Place the CD with the label side up on the disc tray correctly. , Clean the CD (see page 17). , Moisture has condensed inside the player. Remove the disc and leave the player turned on for about an hour (see page 17). , Place the CD in the correct position on the disc tray. The remote does not function. (CDP-CE345 only) , Remove the obstacles in the path of the remote and the player. , Point the remote at the remote sensor on the player. , Replace all the batteries in the remote with new ones if they are weak. The player functions incorrectly. , The microcomputer chips may be operating incorrectly. Turn the power off, then turn it back on to reset the player. Specifications Compact disc player Laser Semiconductor laser (λ = 780 nm) Emission duration: continuous Laser output Max 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. Frequency response 2 Hz to 20 kHz ± 0.5 dB Dynamic range More than 93 dB Harmonic distortion Less than 0.0045 % Output ANALOG OUT DIGITAL OUT (OPTICAL) Jack type Phono jacks Optical output connector Maximum output level 2 V (at 50 kilohms) –18 dBm Load impedance Over 10 kilohms Wave length: 660 nm General Power requirements Power consumption 11 W Dimensions (approx.) 430 × 110 × 398 mm (w/h/d) (17 × 4 3/8 × 15 3/4 in.) incl. projecting parts Mass (approx.) 5 kg (11 lbs 1 oz.) Supplied accessories See page 4. Design and specifications are subject to change without notice. Where purchased Europe and some Asian countries Australia Other countries Power requirements 220 V - 230 V AC, 50/60 Hz 240 V AC, 50/60 Hz 110 V - 120 V or 220 V - 240 V AC, adjustable, 50/60 Hz
Additional Information Additional Information 19GB Index A, B AMS 10 Automatic Music Sensor. See AMS C, D Connecting 4 Continuous Play 6 E Editing. See Recording F, G Fading 15 Time Fade 15 H, I, J, K Handling CDs 17 Hookups 4 overview 4 L Locating by monitoring 10 by observing the display 10 by scanning 10 using AMS 10 M, N, O Music Scan 10 P, Q Peak search 16 Playback Continuous Play 6 Program Play 12 Repeat Play 11 Shuffle Play 11 Program 12 changing 13 checking 13 for recording 14 R Recording 14 a program 14 using Time Edit 14 Remaining time 8 Remote control 4 Repeating 11 Replacing discs while playing a disc 9 Names of controls Buttons ANALOG OUT LEVEL +/– 5 CHECK 13 CLEAR 13 CONTINUE 6 DISC 1 - 5 9 DISC SKIP 7 EDIT/TIME FADE 14, 15 EX-CHANGE 9 FADER 15 MUSIC SCAN 10 A OPEN/CLOSE 6 PEAK SEARCH 16 PROGRAM 12 REPEAT 11 SHUFFLE 11 TIME 8 H 7 X 7 x 7 m/M 10 ./> 10 Switch POWER 6 Control l AMS L 7 Jacks ANALOG OUT 4 DIGITAL OUT 4 Others Disc tray 6 Display 8 4 S Scanning. See Music Scan Searching. See Locating Select Shuffle Play 11 Shuffle Play 11 T Time Edit 14 Time Fade 15 Total playing time 8 Troubleshooting 18 U Unpacking 4 V, W, X, Y, Z Voltage Selector 5 Index
Información adicional 20ES Sony Corporation Printed in China
Have a question about the Sony CDP-CE245 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Sony CDP-CE245. Please make sure that you describe your difficulty with the Sony CDP-CE245 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.