Samsung SPD-400 manual

View a manual of the Samsung SPD-400 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Samsung
  • Product: Digital decoder
  • Model/name: SPD-400
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 0
NETWORK VIDEO DECODER
User Manual SPD-400
Page: 1
Copyright
©2011 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the
problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
 Design and specifications are subject to change without prior notice.
 The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
Network Video Decorder
User Manual
Page: 2
English _3
●
OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety, If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
overview
Page: 3
overview
4_ overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
Page: 4
English _5
●
OVERVIEW
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
It is essential that when changing the battery in the unit, the replacement
battery must be of the same type otherwise there may be a possibility of an
explosion.
CALIFORNIA USA ONLY
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/
hazardouswaste/perchlorate.”
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not
be connected.
Page: 5
overview
6_ overview
Please read the following recommend safety precautions carefully.
 Do not Place this apparatus on an uneven surface.
 Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
 Do not place this apparatus near conductive material.
 Do not attempt to service this apparatus yourself.
 Do not place a glass of water on the product.
 Do not install near any magnetic sources.
 Do not block any ventilation openings.
 Do not place heavy items on the product.
User’s Manual is a guidance book how to use the products
The meaning of the using sign in the book is following
 Reference : In case of providing information for helping of product’s usages
 Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
 Please read this manual for the safety before using of goods and keep it in
the safe place.
Page: 6
English _7
●
OVERVIEW
CONTENTS
OVERVIEW
3
3 Important Safety Instructions
9 Product Features
9 Recomended PC Specifications
10 What’s Included
11 At a Glance
INSTALLATION &
CONNECTION
14
14 Connecting with other Device
NETWORK CONNECTION
AND SETUP
19
19 Configuring Network Video Decoder in
LAN Environments
20 Connecting the Network Video
Decoder Directly to DHCP-Based
DSL/Cable Modem
21 Connecting the Network Video
Decoder and Broadband Router that
is Connected to the Cable Modem
22 Buttons used in IP Installer
23 Static IP Setup
27 Dynamic IP Setup
28 Connecting to the Network Device
from a Shared Local PC
Page: 7
overview
8_ overview
WEB VIEWER
29
29 Accessing the Network Video Decoder
30 Login
SETUP SCREEN
31
31 Setup
31 Audio & Video Setup
39 Network Setup
43 System Setup
APPENDIX
48
48 Specification
50 Product Overview
51 Troubleshooting
52 Open Source Announcement
54 GPL/LGPL Software License
Page: 8
English _9
●
OVERVIEW
PRODUCT FEATURES
 Supports Multi-format decoding
The network video decoder employs H.264/MPEG-4/MJPEG multi-format decoder to
decode and display up to 4 video streams transferred through network.
 Supports Full-HD Video Display
The maximum supported output resolution is 1920x1080, and provides HDMI, VGA and
CVBS (BNC) output ports for display.
 Alarm Monitoring
When an event occurs at a network camera or the encoder, the monitoring display switches
to the corresponding video according to the settings.
RECOMENDED PC SPECIFICATIONS
 CPU : Intel(R) Core(TM)2 2.00 GHz or higher
 Operating System : Windows XP, VISTA, 7
Mac OS
 Resolution : 1280X1024 pixels or higher
 RAM : 1GB or higher
 Web Browser : Internet Explorer 7.0 or 8.0, Firefox, Chrome, Safari
 Video Memory : 128MB or higher
Page: 9
overview
10_ overview
WHAT’S INCLUDED
Please check if your network video decoder and accessories are all included in the product
package.
Appearance Item Name Quantity Description
VIDEO OUT
AUDIO OUT HDMI VGA
SPD-400 1
User Manual CD 1
Quick Guide 1
ASSY-Tapping Screw 4 Used for installation on the wall
Page: 10
English _11
●
OVERVIEW
AT A GLANCE
Front Side
Item Description
 AUDIO OUT
This port outputs selected audio from the device connected through the
network, according to the settings.
b VIDEO (CVBS) OUT
A BNC output port for display.
This port outputs video only if CVBS mode is selected.
c HDMI
An HDMI output port for display.
This port outputs video only if HDMI or VGA mode is selected.
 VGA
A VGA output port for display.
This port outputs video only if HDMI or VGA mode is selected.
VIDEO OUT
AUDIO OUT HDMI VGA
Page: 11
overview
12_ overview
Rear Side
Item Description
 NETWORK Used to connect a LAN cable.
b USB This function is not currently available.
c I/O Port
RS-485 D+/D- This function is not currently available.
NO1/NO2 Alarm Out (for Normal Open)
CM1/CM2 Alarm Out (for Common)
NC1/NC2 Alarm Out (for Normal Close)
S1 An alarm input sensor port.
G Earth-grounding port for external signal.
 RESET
This button initializes network video decoder settings, or selects the monitor
output.
Press and hold for 5 seconds or longer, then the system indicator turns off,
settings are initialized, and will restart.
Press the button for about 1 second, then the MONITOR LED color changes
as the video output mode changes.
MONITOR
POWER
DC 12V
–
+
NETWORK
ACT LINK
USB NO1 CM1 NC1 NO2 CM2 NC2 G S1 D+ D–
RELAY OUT RS-485
SENSOR
RESET
Page: 12
English _13
●
OVERVIEW
Item Description

Power,
Monitor LED
MONITOR
Indicates the video output mode.
Green : HDMI or VGA output mode.
Yellow : CVBS output mode.
 To change the video output mode, change it in Web
Viewer’s video settings or press the [RESET] button
for about 1 second.
POWER
ON : While the power is on.
OFF : If the power is off.
 Power Port Used to connect the specified power source.
 GND Used for earth-grounding.
Page: 13
14_ installation & connection
installation & connection
CONNECTING WITH OTHER DEVICE
Connecting Video Out
Connect a monitor to the preferred video output of the network video decoder.
J  It outputs video through the port according to the setting configured in the Web Viewer’s “Display
Setup > Monitor”. (Page 37)
 When in HDMI or VGA output mode, the display may not render properly if configured resolution is
not supported by the monitor.
 Press and hold [RESET] button for about 1 second to change the video output mode.
 The MONITOR LED changes its color accordingly.
AUDIO OUT
VGA
VIDEO OUT
HDMI
Network
Amp Speaker
Monitor Monitor Monitor
Camera
Microphone
Page: 14
English _15
●
INSTALLATION
&
CONNECTION
Connecting Audio In/Out
1. Connect a microphone to the network camera or encoder, and set Audio setting of
corresponding device to <ON>.
2. Set Network AUDIO SETUP to ON in Video Decoder’s single layout settings, and
select its output from Line Out and HDMI out in Audio Settings. Note that HDMI
OUT for audio output can be selected only when the monitor out is set to HDMI.
3. When using Line Out, connect the speaker’s LINE IN and Network Video Decoder’s
AUDIO OUT terminals.
4. For HDMI output, connect an HDMI monitor to HDMI port.
 For HDMI audio output, a monitor with built-in speaker is required.
J  There is some possibility that HDMI audio doesn’t work with some specific monitors.
Page: 15
installation & connection
16_ installation & connection
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the network encoder.
J  Be careful not to reverse the polarity when you connect the power cable.
 Please make sure the monitor and network video decoder are turned off when connecting them.
Ethernet Power
MONITOR
POWER
DC 12V
–
+
NETWORK
ACT LINK
USB NO1 CM1 NC1 NO2 CM2 NC2 G S1 D+ D–
RELAY OUT RS-485
SENSOR
RESET
Page: 16
English _17
●
INSTALLATION
&
CONNECTION
Connecting to the I/O port box
Connect the Alarm I/O signal to the corresponding port of the rear port box.
Connecting to the Alarm Input
Connect one signal cable (out of 2) of applicable sensor to the [S1] port, and the other to
the [G] port.
Connecting the Alarm Output
Connect one signal cable (out of 2) of applicable external device to the [RELAY OUT(NC, NO)],
and the other to the [CM] port.
MONITOR
POWER
DC 12V
–
+
NETWORK
ACT LINK
USB NO1 CM1 NC1 NO2 CM2 NC2 G S1 D+ D–
RELAY OUT RS-485
SENSOR
RESET
NO1 CM1 NC1 NO2 CM2 NC2 G S1 D+ D–
RELAY OUT RS-485
SENSOR
Page: 17
installation & connection
18_ installation & connection
Alarm I/O Wiring Diagram
ALARM OUT
NO1
ALARM OUT
NO2
ALARM OUT
NC1
ALARM OUT
NC2
ALARM IN
(12mA sink)
(24VDC 1A,
125VAC 0.5A MAX)
(24VDC 1A,
125VAC 0.5A MAX)
GND
3.3V
ALARM COM
CM1
ALARM COM
CM2
3
Page: 18
English _19
●
NETWORK
CONNECTION
AND
SETUP
You can configure the Network Video Decoder’s network settings to your preference.
CONFIGURING NETWORK VIDEO DECODER IN LAN
ENVIRONMENTS
Accessing the Network Video Decoder from a PC within the same LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the Network Video Decoder into the browser’s address field.
M  A remote PC in an external Internet out of the LAN network may not be able to connect to the
network video decoder installed in the intranet if a firewall is set.
In this case, to resolve the problem, contact your network administrator.
 The default IP address is set to 192.168.1.200.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 23)
network connection and setup
Switch
HUB
AUDIO OUT
VGA
VIDEO OUT HDMI
Network Video Decoder
Local PC
Firewall
Network Camera
DDNS Server
(Data Center, KOREA)
INTERNET
<Local Network>
Network Camera
Page: 19
20_ network connection and setup
network connection and setup
CONNECTING THE NETWORK VIDEO DECODER DIRECTLY
TO DHCP-BASED DSL/CABLE MODEM
1. Use a cross cable to connect a computer and the Network Video Decoder.
2. Run the IP Installer and change the IP address of the Network Video Decoder so
that you can use the web browser on your desktop to connect to the Internet.
3. Access the Network Video Decoder using an Internet browser.
4. Move to [Setup] page.
5. Move to [Network] – [Interface], and set the network type to [DHCP].
6. Connect the Network Video Decoder, which was removed from your PC, directly to
the modem.
7. Restart the Network Video Decoder.
M  For setting the network type, refer to “Interface”. (page 39)
AUDIO OUT
VGA
VIDEO OUT HDMI
Network Video Decoder Network Camera
DDNS Server
(Data Center, KOREA)
DSL/Cable Modem
INTERNET
Page: 20
English _21
●
NETWORK
CONNECTION
AND
SETUP
CONNECTING THE NETWORK VIDEO DECODER AND
BROADBAND ROUTER THAT IS CONNECTED TO THE
CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
Configuring the network settings of the local PC connected to a
Broadband Router
Configuring the network settings of the local PC connected to a Broadband Router, follow
the instructions below.
 Select : <Network Neighborhood>  <Properties>  <Local Area Connection>
 <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 
<Obtain an IP address automatically> or <Use the following IP address>.
 Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1
IP address : 192.168.1.200
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address : 192.168.0.200
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address : 192.168.xxx.200
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
M  For the address of the Broadband Router, refer to the product’s documentation.
AUDIO OUT
VGA
VIDEO OUT HDMI
Network Video Decoder
Broadband
Router
Cable Modem Cable Modem
Network Camera
DDNS Server
(Data Center, KOREA)
INTERNET
Network Camera
Local PC
Page: 21
22_ network connection and setup
network connection and setup
BUTTONS USED IN IP INSTALLER
Item Description
 Device Name
Model name of the connected network device.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b Alias This function is not currently implemented.
c Mode
Displays either <Static> or <Dynamic> for the current network connection
status.

MAC(Ethernet)
Address
Ethernet address of the connected network device.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
 IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
The factory default is “192.168.1.200”.
 Protocol
Network settings of the network device.
The factory default is “IPv4”.
Network encoders with the IPv6 setting will be displayed “IPv6”.
Page: 22
English _23
●
NETWORK
CONNECTION
AND
SETUP
Item Description
 URL Shows URL address.
 IPv4 Scans for network device with the IPv4 setting.
 IPv6
Scans for network device with the IPv6 setting.
Activated in an IPv6 compliant environment.
	 Search
Scans for network devices that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

 Auto Set The IP Installer automatically configures the network settings.
 Manual Set You should configure the network settings manually.
m Exit Exits the IP Installer program.
M  For the IP installer, use only the installer version provided in the installation CD or use the latest
one if available.
You can download the latest version from the Samsung web site (www.samsungipolis.com).
STATIC IP SETUP
Manual Network Setup
Run <IP Installer_vX.XX.exe> to display the network device search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M  For network devices found with the IPv6 setting, these buttons will be grayed out as the network
devices do not support this function.
1. Select a network device from the
search result.
Find the MAC (Ethernet) address labeled
on the rear of the network device.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
The default values of <IP Address>, <Subnet Mask>, <Gateway>, <HTTP Port>
and <VNP Port> of the network device will be displayed.
Page: 23
24_ network connection and setup
network connection and setup
3. In the <Address> pane, provide the
necessary information.
 MAC (Ethernet) Address : The MAC
(Ethernet) address of the applicable
network device will be set automatically
so you don’t need to input it manually.
M  You can configure the static IP settings
only if the DHCP checkbox is unchecked.
If not using a Broadband Router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network
administrator.
4. In the <Port> pane, provide
necessary information.
 HTTP Port : Used to access the
network device using the Internet
browser, defaulted to 80.
Use the spin button to change the
HTTP Port value.
 VNP Port : Used to control video
transfer from a network camera or encoder.
The Network Video Decoder’s VNP port needs no configuration. The default value
is 1234, which is not to be modified.
5. Enter the password.
This is the login password for the “admin” user who accesses the network device.
The default password is “4321”.
J  The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
6. Click [OK].
Manual network setup will be completed.
Page: 24
English _25
●
NETWORK
CONNECTION
AND
SETUP
If using a Broadband Router
 IP Address : Enter an address falling in
the IP range provided by the Broadband
Router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254
 Subnet Mask : The <Subnet Mask>
of the Broadband Router will be the
<Subnet Mask> of the Network Video
Decoder.
 Gateway : The <Local IP Address> of the Broadband Router will be the <Gateway>
of the Network Video Decoder.
M  The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
If the Network Video Decoder is connected to a Broadband Router
Configure the IP related settings and the Port related settings distinctly with each other.
Category Decoder #1 Decoder #2
IP related settings
IP Address
Subnet Mask
Gateway
192.168.1.200
255.255.255.0
192.168.1.1
192.168.1.201
255.255.255.0
192.168.1.1
Port related settings HTTP Port 8080 8081
M  If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar
of the Internet browser before you can access the Network Video Decoder.
ex) http://IP address : HTTP Port
http://192.168.1.200:8080
Page: 25
26_ network connection and setup
network connection and setup
Auto Network Setup
Run <IP Installer_vX.XX.exe> to display the network device search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M  For network devices found with the IPv6 setting, these buttons will be grayed out as the cameras
do not support this function.
1. Select a network device from the
search result.
Find the MAC (Ethernet) address labeled
on the rear of the network device.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically.
3. Enter the password.
This is the login password for the
“admin” user who accesses the
network video decoder.
The default password is “4321”.
 The default password can be exposed to a
hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related
issues caused by the unchanged password
shall be responsible for the user.
4. Click [OK].
Auto network setup will be completed.
Page: 26
English _27
●
NETWORK
CONNECTION
AND
SETUP
DYNAMIC IP SETUP
Dynamic IP Environment Setup
 Example of the Dynamic IP environment
- If a Broadband Router, with a network device connected, is assigned an IP ad-
dress by the DHCP server
- Network device is connected to a DHCP based modem directly
- If IPs are assigned by the internal DHCP server via the LAN
Checking the Dynamic IP
1. From a local PC, run <IP Installer> to
display a list of network devices that are
assigned <Dynamic IP>.
2. Select a network device in the list,
and click [Manual Set] to check the
<Dynamic IP> of the network device.
If you uncheck <DHCP>, you can
change IP to <Static>.
Page: 27
28_ network connection and setup
network connection and setup
CONNECTING TO THE NETWORK DEVICE FROM A
SHARED LOCAL PC
1. Run the IP Installer.
Searches for connected network
devices and displays on the list.
2. Double click the desired network device
to connect to.
The Internet browser starts and
connects to the network device.
M  You can also access the camera in such way you type the IP address of the found network device
in the address bar of the Internet browser
Page: 28
English _29
●
WEB
VIEWER
web viewer
ACCESSING THE NETWORK VIDEO DECODER
Normally, you would
1. Launch the Internet browser.
2. Enter the Network Video Decoder’s IP
address into the address field.
ex) • IP address (IPv4) : 192.168.1.200
 http://192.168.1.200
- the Login dialog should appear.
• IP address (IPv6) : 2001:0230:abcd:ffff
:0000:0000:ffff:1111
 http://[2001:230:abcd:ffff:::ffff:1111]
- the Login dialog should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Enter the Network Video Decoder’s IP address and HTTP port number into the
address field.
ex) IP address : 192.168.1.200:HTTP Port number(8080)
 http://192.168.1.200:8080
- the Login dialog should appear.
Page: 29
web viewer
30_ web viewer
LOGIN
The default user ID is “admin”, and the default password is “4321”.
1. Enter “admin” in the <User Name>
input box.
2. Enter “4321” in the <Password> input
box.
If the password is changed, enter the
changed password instead.
3. Click [OK].
Once logged in, the network video
decoder’s setup screen appears.
M  For security purposes, ensure that you
change the password in <System>
- <User>.
The administrator ID,“admin”, is fixed
and can not be changed.
 The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
 If you check the “Remember my password” option when your input is done, in future you will be
logged in automatically without being prompted to enter the login information.
J  If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best
quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders.
Page: 30
English _31
●
SETUP
SCREEN
SETUP
You can configure the audio & video, network, event and system settings of the network video
decoder remotely.
J  Depending on the firmware version of network camera/encoder, registering such devices to the
network video decoder may fail or work improperly.Visit www.samsungtechwin.com to download
the latest firmware and update it.
AUDIO & VIDEO SETUP
Video & Sequence
1. From the Setup menu, select the
<Audio & Video ( )> tab.
2. Select <Video & Sequence>.
3. Click the input box of each item and
enter / select a desired value.
 Display layout : Select a desired
layout for the monitoring screen from
the single or quad layout.
 Sequence setup: Select whether to
use automatic monitoring sequence,
and select layout and dwell time of the sequenced layout.
 The display automatically cycles through the assigned layouts according to the configured dwell
time in the sequence of the setting. Up to 10 layouts can be selected from the single and quad
layouts and sequenced.
 Single layout : You can add network camera/encoder operating in the network, or
edit/delete registered single layouts.
 It is the basic unit of display layout for network camera/encoder connected to the network video
decoder.
After adding a network camera/encoder’s single layout, select the added single layout’s camera
name to display the network camera/encoder’s video on the monitoring screen.
Up to 20 network cameras or encoders can be added.
 Quad layout: You can composite, edit or delete a 4-split layout by selecting added
single layouts.
 Compose a quad layout by selecting single layouts of network camera/encoder for displaying
4-split monitoring screen.
Assign added single layouts of network cameras/encoders to a quad layout, and select the
composed quad layout to display 4-split screen on the monitor. Up to 8 quad layouts can be added.
setup screen
Page: 31
setup screen
32_ setup screen
To add a single layout
1. Click the [Add video ( )] button.
2. Enter the network camera/encoder’s
information.
3. Enter the IP address or DDNS URL
of the device to be added into the
<Address> field.
 Up to 64 letters can be entered, and the layout
list displays up to 9 letters and <…> will
appear for the rest.
4. Enter the ID and password for the
device to be added.
5. Click [Import Properties ( )] button
to fetch information on the device to be
connected.
 Check <Include additional user profiles>
to fetch user-defined profiles added to the
device to be connected. For AXIS cameras, all
available profiles are imported regardless of this option.
 Cannot add the camera if it has no profile.
Page: 32
English _33
●
SETUP
SCREEN
6. Enter the <Camera name> after the
fetched information appears.
 The camera name allows no blank space
within the name.
 Up to 15 letters can be entered, and the layout
list displays up to 7 letters and <…> will
appear for the rest.
7. Select a profile.
8. Click the [Add ( )] button.
M  Up to 20 layouts can be added.
 Click [Camera Setting ( )] button to
display a browser for accessing the added
camera’s web page.
Available resolutions for single layout
CODEC H.264 MPEG-4 MJPEG
Single layout 1920x1080p~ 320x240 4CIF ~ 320x240
1280x720p ~ 320x240
(except 800x600)
Page: 33
setup screen
34_ setup screen
To edit existing layout
1. Click the checkbox to select an added
device.
2. Edit the existing information.
 Note that <Protocol> and <Address> fields
are not allowed to edit.
3. Click [Save ( )].
4. To cancel, click the [Cancel ( )]
button.
To delete existing layout
1. Click the checkbox to select an added
device.
2. Click [Delete ( )] button on the top
of the layout list.
3. When a confirmation message appears,
click [OK].
M  A layout that is used by a <Quad layout> or in the <Sequence setup>, or currently displayed
on the monitoring screen cannot be changed or deleted, and such an attempt will display a
confirmation message.
To set the audio for the added single layout
1. From the list of added single layouts,
set the audio to <ON> or <OFF> to
your preference.
- For a device configured to output
audio, it cannot be switched from
<OFF> to <ON> in quad mode
layout. A confirmation message appears on such an attempt.
- Audio can be selected only when the device’s audio output is set to <ON> in its
single layout configuration.
Page: 34
English _35
●
SETUP
SCREEN
To add a quad layout
1. Click the [Add quad layout ( )]
button.
2. Select devices from the added single
layouts to be assigned to each channel.
3. Enter the <Layout name>.
 Up to 15 letters can be entered, and the layout
list displays up to 7 letters and <…> will
appear for the rest.
4. Select the audio output channel of the quad layout from the assigned 4 channels.
You can select a device if the device’s audio is set to <ON> in its single layout.
5. Click the [Add ( )] button.
M  Up to 8 quad layouts can be added. Note that one single layout cannot be assigned to the same
quad layout multiple times.
However, a single layout can be assigned to multiple quad layouts.
Available resolutions for quad layouts
Some resolutions may not be supported by quad layout of the Network Video Decoder,
depending on the CODEC used.
Selecting a not supported resolution will display an error message.
Before adding, refer to the available resolutions below.
CODEC H.264 MPEG-4 MJPEG
Quad layout
1280x720p ~ 320x240
(except 800x600)
4CIF ~ 320x240
1280x720p ~ 320x240
(except 800x600)
M  In Quad mode display of resolution less than 960x540, each video will be centered to its split
screen if all 4 channels’ videos have the same resolution.At the moment, 320x240 and 352x240
video will be enlarged to 640x480 and 704x480 respectively.
<2nd split displays video having resolution of less than 960x540>
Page: 35
setup screen
36_ setup screen
To edit a quad layout
1. Click the select checkbox of the desired layout from the list.
2. Make your changes with assigned channel or edit the layout name.
3. Click [Save ( )].
4. To cancel, click the [Cancel ( )] button.
To delete a quad layout
1. Click the select checkbox of the desired
layout from the list.
2. Click the [Delete ( )] button.
3. When a confirmation message appears,
click [OK].
M  A QUAD layout that is included in the
<Sequence setup>, or currently
displayed on the monitoring screen cannot be changed or deleted, and such an attempt will
display a confirmation message.
Page: 36
English _37
●
SETUP
SCREEN
To set a sequence
1. Press the [Sequence setup ( )]
button.
2. Select layouts in the order you want to
display in sequence.
3. Enter the interval of the layout transition.
4. When done, click [Apply ( )].
5. Set the sequence setup to <ON>.
Selected layouts are displayed in
the specified order, switched at the
specified interval.
To select the layout to be displayed on the monitor
You can set a layout to be displayed on a connected monitor.
1. Click the “Display layout” list to display
available layouts.
Select a layout to be displayed on the
screen.
2. When done, click [Apply ( )].
 If the Sequence Setup is set to <ON>, the <Display layout> listbox is disabled.
Display setup
1. From the Setup menu, select the
<Audio & Video ( )> tab.
2. Click <Display setup>.
3. Click the input box of each item and
enter / select a desired value.
 Monitor : Select the target monitor
type for video display.
 Resolution : Select the monitor’s
resolution.
 When selected <CVBS>, the menu will be
changed to <CVBS type>.
Page: 37
setup screen
38_ setup screen
 OSD position : Selects the position of the on-screen display menu.
If you change the number of OSD positions it will be moved to set number based
on the entire screen.
 OSD display : Select types of OSD to be
displayed on the monitor.
 Camera name : Shows the camera’s
name used when registering the layout.
b Decoder time : Shows the time set to the
decoder.
c Alarm / Error : Shows alarm/error on the
monitor when occurred.
 IP address : Shows the camera’s IP
address.
 Border : Separates each camera’s screen with border lines.
 Preview ( ) : Previews changed OSD related settings, and applies when
confirmed.
Applying OSD setup changes does not affect monitor settings.
4. When done, click [Apply ( )].
Audio setup
You can setup audio in/out settings of devices connected to the network video decoder.
1. From the Setup menu, select the
<Audio & Video ( )> tab.
2. Click <Audio setup>.
3. Adjust the audio I/O levels to your
preference.
 Audio output : Set whether to use
audio or not, and its output method.
 Gain : It is enabled when selected <Line out>, and set the value.
M  Audio is produced only if the device connected supports audio input and set to on.
 To select HDMI audio out, the Monitor setting of Display Setup should be set to HDMI.
4. When done, click [Apply ( )].
Gate1
192.168.1.201
01:01:01



b
c
Page: 38
English _39
●
SETUP
SCREEN
NETWORK SETUP
Interface
1. From the Setup menu, select the
<Network ( )> tab.
2. Click <Interface>.
3. Set the <Connection mode> and
<IPv6 setup> as necessary.
 IP type : Select an IP connection
type.
- Manual : Specify the IP address,
Subnet Mask, Gateway, DNS1,
and DNS2.
- DHCP : Specify the DNS1 and
DNS2.
 If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
 MAC address : Shows the Network Video Decoder’s MAC address.
 IP address : Displays the current IP address.
 Subnet mask : Displays the <Subnet Mask> for the set IP.
 Gateway : Displays the <Gateway> for the set IP.
 DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
 HTTP port : HTTP port used to access the Network Video Decoder via the web
browser. The default is 80 (TCP).
 IPv6 use : Specify the use of IPv6.
 IPv6 address : Obtains the IPv6 address to access the IPv6 network.
4. When done, click [Apply ( )].
Page: 39
setup screen
40_ setup screen
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the
<Network ( )> tab.
2. Click <SSL>.
3. Select a secure connection system.
 When accessing the Network Video
Decoder using secure HTTPS mode, enter
the IP address into the address field as:
https://<Network Decoder_IP>.
4. Search and add a certificate for the
Network Video Decoder.
To install the certificate to the Network Video Decoder, you need to type in the
certificate name (it can be arbitrarily assigned by user), and specify the certificate file
issued from the authority, and a key file.
 The <HTTPS(Secure connection mode using the public certificate)> item will be active only if
there exists a public certificate installed.
5. When done, click [Apply ( )].
Installing the Certificate
1. Enter the certificate’s name.
2. Select the desired certificate file and its key file, and click [Install ( )] button.
Deleting a certificate
1. Click [Delete ( )] button.
2. To delete a public certificate, you should access the network video decoder in
the mode of <HTTP (Do not use secure connection)> or <HTTPS (Secure
Connection mode using a unique certificate)>.
Page: 40
English _41
●
SETUP
SCREEN
Alarm input
You can set the alarm input type, duration and action type of the Network Video Decoder’s
alarm input port.
1. From the Setup menu, select the
<Event ( )> tab.
2. Click <Alarm input>.
3. Select the input device type.
 Type
- Normal open : It is normally open,
but if it is closed, an alarm will be
triggered.
- Normal close : It is normally closed,
but if it is open, an alarm will be
triggered.
4. Specify the <Activation time>.
 Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
 Only scheduled time : Check if an alarm occurs at a specified day of the week for
a specified time period. It activates in operated mode when the alarm occurs.
5. Set the alarm’s output dwell time when an alarm occurs.
 Alarm output : Specify the alarm output time in the alarm input setup.
 If the alarm out duration is set to <Always>, the alarm continues to function until the alarm
acknowledge button is pressed, as expressed in Audio & Video page.
 Test : Conducts a test alarm for the connected alarm out device.
6. When done, click [Apply ( )].
Page: 41
setup screen
42_ setup screen
Event input
You can set the alarm duration and alarm’s action type of the network camera or encoder.
1. From the Setup menu, select the
<Event ( )> tab.
2. Click <Event input>.
3. Specify an event input device.
 Input device setup
- Motion Detection : Recognizes
a detected motion from the
connected device as an alarm.
- Intelligent video : Recognizes a
detected intelligent video analysis
event from the connected device
as an alarm.
- Cam alarm : Recognizes a sensor input event from the connected device as an
alarm.
M  Operable only when the camera registered to the layout supports applicable function and set to
on.
4. Specify the activation time.
 For <Activation time> setup, refer to “Alarm input”. (Page 41)
5. Set <Alarm out duration> for each alarm.
6. Select the <Layout> for each device’s video display on an event.
If <Quad> mode is selected and the desired single layout is assigned to two quad
layouts, the quad layout having smaller layout number is selected and displayed.
When an event occurs, the layout selected for the event is displayed along with
alarm border and alarm message according to the specified display setup, until the
alarm acknowledge button is pressed in the Audio & Video page.
When the alarm acknowledge button is pressed, the screen returns to the layout
previous to the event.
7. When done, click [Apply ( )].
Page: 42
English _43
●
SETUP
SCREEN
SYSTEM SETUP
Product information
1. From the Setup menu, select the
<System ( )> tab.
2. Click <Product information>.
3. Check the Network Video Decoder
information, or provide details according
to your network environment.
 Device name : Enter the Network
Video Decoder’s name.
 Location : Describe the location of the installed Network Video Decoder.
 Description : Enter the additional detailed information on the installed Network
Video Decoder.
 Memo : Provide an explanation about the network encoder for better understanding.
 Language : Select a preferred language for the network encoder menus and the
Web Viewer OSD.
4. When done, click [Apply ( )].
Date & Time
1. From the Setup menu, select the
<System ( )> tab.
2. Click <Date & Time>.
3. Set the network video decoder’s
system time.
 Current system time : Displays the
current time settings of your system.
 Timezone : Specify the local time
zone based on the GMT.
 Use daylight saving time : If the region
of installed location is applicable with
DST, you can select whether to apply
DST or not.
Page: 43
setup screen
44_ setup screen
 System time setup : Specify the time and date that will be applied to your system.
- Manual : Specify the time manually.
- Synchronize with NTP server : Sync with the time of the specified server address.
- Synchronize to PC Viewer : Synchronize the time with the connected PC.
4. When done, click [Apply ( )].
M  If you select the <Synchronize to PC Viewer>, the standard timezone should be set the same
as the current timezone in PC.
User
1. From the Setup menu, select the
<System ( )> tab.
2. Click <User>.
3. Provide the necessary user information.
 Administrator password change :
Change the current password for the
administrator.
 The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
 Current user : You can change the user information and adjust the permission level
for a user who is set to <Enable>.
- controls : If set to on, all menu items except the user account administration
can be used.
- Enable : Activates the user account.
4. When done, click [Apply ( )].
Page: 44
English _45
●
SETUP
SCREEN
Upgrade/Reboot
1. From the Setup menu, select the
<System ( )> tab.
2. Click <Upgrade/Reboot>.
3. Select a desired item and set it
appropriately.
 Upgrade : Performs upgrading the
system.
 Factory default : Resets the system
to the factory default.
- Except network parameter : Resets all settings except for the Network Parameters.
- All : Resets all settings including the Network Parameters.
 Configuration backup & Restore : Backs up the current system settings before
performing the restoration process. The system is automatically restarts after
backup or restoration.
 Restart : Restarts the system.
To perform the upgrade
1. Click [ ].
2. Click [ ] and specify a file to
upgrade.
3. Click [Upgrade].
4. The “Update status” dialog appears
where the progression will be shown in
the bottom.
M  If you forcibly terminate the upgrade
process, upgrade will not be completed
properly.
Page: 45
setup screen
46_ setup screen
To save the current settings and restore the backup settings
1. Click [Backup].
The Save As dialog should appear.
2. Specify the backup path with a proper
file name, and click [Save].
The backup file will be saved to the
specified path in the format of “.xml”.
3. To restore the settings from a backup,
select the backup file.
4. Click [Restore].
Once the restoration completes, the
system will restart.
Page: 46
English _47
●
SETUP
SCREEN
Log
You can check the system log or event log.
1. From the Setup menu, select the
<System ( )> tab.
2. Click <Log>.
3. Select a log type.
 Syslog : You can check the system
logs where any system changes
are recorded including the time
information.
 Evtlog : You can check the event
logs including the time information.
4. From the right log list, select an item to
search for.
 If you select <All> in the top left dropdown list, all logs for the applicable log type
will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to
the previous, next, or the last item.
M  If you want to view the details of a log, click [Source ( )] in the right column of the log; the log
information will be shown in the bottom pane.
 Each page displays 15 logs with the latest one displayed at the top.
 The event/system log list can contain up to 1000 logs; after that, the existing logs will be deleted
from the oldest one each time a new log is created.
Page: 47
appendix
48_ appendix
SPECIFICATION
Items Description
Video Out
Video Out
1) HDMI / VGA : Max 1920x1080p (same output resolution for
HDMI, VGA) 1920x1080p, 1680x1050, 1600x900, 1440x900,
1280x1024, 1280x720p, 1024 x 768
2) CVBS : NTSC : 1.0 Vp-p / 75Ω composite 704x480
PAL : 1.0 Vp-p / 75Ω composite 704x576
3) Select from HDMI/VGA, CVBS
Video Latency
1) H.264 : 3.5 seconds in maximum
2) MPEG-4 : 2 seconds in maximum
3) MJPEG : 2 seconds in maximum
Event Trigger Alarm input, Network camera event input
Alarm I/O Input 1ea / Output 2ea (Relay)
Network
Ethernet RJ-45 (10/100/1000BASE-T)
Video Compression
Format
H.264, MPEG-4, MJPEG
Resolution
1) H.264
- Single View :1920x1080p ~ 320x240
- Quad View : 1280x720p ~ 320x240 (except 800x600)
2) MPEG-4 :
- Single View : 4CIF ~ 320x240
- Quad View : 4CIF ~ 320x240
3) MJPEG :
- Single VIew : 1280x720p ~ 320x240 (except 800x600)
- Quad VIew : 1280x720p ~ 320x240 (except 800x600)
1920x1080p, 1280X1024, 1280X720p, 704x576, 704x480,
640x480, 352x288, 352x240, 320x240
Max. Framerate
Max. 30fps at single view, Max. 120fps at 4x (640x480), Max.
100fps at 4x4 CIF, Max 60fps at 4x720p (when audio is disabled)
Display Single layout, Quad layout
appendix
Page: 48
English _49
●
APPENDIX
Items Description
Network
Audio I/O 1 Line Out
Audio Compression
Format
G.711
IP IPv4, IPv6
Protocol
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), NTP, HTTP, DHCP, ICMP, IGMP,
ARP, SSL, DNS
Security
HTTPS(SSL) Login Authentication
User access Log
Camera connections 20 cameras, 8 layouts, 10 sequences
ONVIF Conformance Not supported
Supported Devices
Samsung : SNV-3120, SNP-3430H, SNP-3120, 3120V, 3120VH,
SNB-5000, SNB-7000 (Supports profiles of less than 2M), SND-5080/F,
SNV-5080, SNV-5010, SPE-100,400, SPE-1600R/400B
Axis : P3301, P3343, P3344, P1311, P1343, P1344, P1346,
PTZ215, Q6032, Q7401, Q7404 (F/W ver : 5.x)
1) Stream(Live Video/Audio) : SVNP 1.2 (AXIS : RTP/RTSP)
2) Control/Network alarm : SVNP 1.2 (AXIS : Not supported)
Web Viewer
Supported OS : Windows XP / VISTA / 7
Supported Browser : Internet Explorer 7.0 or 8.0, Firefo x2.x, 3.x,
Chrome, Safari
Environmental
Operating Temperature
/ Humidity
+0°C ~ +40°C (+32°F ~ +104°F) / 0% ~ 90% RH
Electrical
Input Voltage DC 12V
Power Consumption Max. 10W
Mechanical
Color / Material Silver / Metal
Dimensions (WxHxD) W178.0 x H34.0 x D128.0mm (W7.00 x H1.33 x D5.03inch)
Weight 530g
Page: 49
appendix
50_ appendix
PRODUCT OVERVIEW
Unit : mm (inch)
107.0
(4.21")
128.0
(5.03")
170.0 (6.69”)
178.0 (7.00”)
34.0
(1.33")

Question & answers

There are no questions about the Samsung SPD-400 yet.

Ask a question about the Samsung SPD-400

Have a question about the Samsung SPD-400 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Samsung SPD-400. Please make sure that you describe your difficulty with the Samsung SPD-400 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.