Pioneer XW-NAS5 manual

View a manual of the Pioneer XW-NAS5 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Cradle / docking station
  • Model/name: XW-NAS5
  • Filetype: PDF
  • Available languages: English, Spanish

Table of Contents

Page: 0
Digital Speaker System for iPod
Sistema digital de parlantes para iPod
ᎍңŪőŰť‫ޠ‬኶՞ඵᖑᏣ‫ق‬ಜ
XW-NAS5
Operating Instructions
Manual de instrucciones
XW-NAS5_FLPWXJ.book 1 ページ 2010年1月26日 火曜日 午後5時18分
Page: 1
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the bottom panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
For Taiwan exclusively
Taiwanese two pin flat-bladed plug
Note: This indication is printed on the inner of the bottom cover.
XW-NAS5_FLPWXJ.book 2 ページ 2010年1月26日 火曜日 午後5時18分
Page: 2
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
These symbols are only valid
in the European Union.
K058c_A1_En
(Symbol examples for batteries)
Pb
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
Information to User
Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate
the equipment.
D8-10-2_A1_En
CAUTION
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use
shielded cables and connectors for connections.
D8-10-3a_A1_En
The following does not apply to the Australia and New Zealand models:
When using this product, confirm the safety
information shown on the bottom of the unit.
D3-4-2-2-4_B1_En
XW-NAS5_FLPWXJ.book 3 ページ 2010年1月26日 火曜日 午後5時18分
Page: 3
4
En
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future
reference.
Contents
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . 5
Before using the remote control . . . . . . . . . . . . 5
Replace the battery . . . . . . . . . . . . . . . . . . . . 5
Using the remote control . . . . . . . . . . . . . . . . 6
Installing the unit . . . . . . . . . . . . . . . . . . . . . . . 6
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
02 Controls and displays
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front /top panel . . . . . . . . . . . . . . . . . . . . . . . . 8
03 iPod playback
Confirm what iPod models are supported. . . . . 9
Connecting your iPod . . . . . . . . . . . . . . . . . . . . 9
Connecting your TV . . . . . . . . . . . . . . . . . . . 10
Playing your iPod . . . . . . . . . . . . . . . . . . . . . . 11
Using the tone controls . . . . . . . . . . . . . . . . 11
04 Bluetooth® ADAPTER for Wireless
Enjoyment of Music
Wireless music play . . . . . . . . . . . . . . . . . . . . 13
Remote control operation. . . . . . . . . . . . . . . 13
Connecting Optional Bluetooth ADAPTER . . . 13
Setting the PIN code. . . . . . . . . . . . . . . . . . . . 14
Pairing Bluetooth ADAPTER and Bluetooth
wireless technology device . . . . . . . . . . . . . . . 14
Listening to Music Contents of Bluetooth
wireless technology device with Your System . . . 15
05 Other connections
Connecting auxiliary components. . . . . . . . . . 16
06 Using the tuner
Connect the FM antenna . . . . . . . . . . . . . . . . 17
Listening to the FM radio . . . . . . . . . . . . . . . . 17
Memorizing stations. . . . . . . . . . . . . . . . . . . 17
Listening to station presets . . . . . . . . . . . . . 17
07 Sound settings
Using the Soundscape . . . . . . . . . . . . . . . . . .18
Adjust the Soundscape volume . . . . . . . . . .18
Select the type of environmental sound . . . .18
Using the sound effects . . . . . . . . . . . . . . . . .19
Adjusting the bass and treble . . . . . . . . . . . . .19
Using the Sound Retriever . . . . . . . . . . . . . . .19
08 Using the timer
Setting the clock . . . . . . . . . . . . . . . . . . . . . . .20
Display mode setting. . . . . . . . . . . . . . . . . . . .20
Changing the clock’s display mode . . . . . . .20
Setting the wake-up timer . . . . . . . . . . . . . . . .20
Turning the wake-up timer on/off . . . . . . . . .21
Using the sleep timer . . . . . . . . . . . . . . . . . . .21
09 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .22
Resetting the system. . . . . . . . . . . . . . . . . . . .23
About iPod/iPhone . . . . . . . . . . . . . . . . . . . . .23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . .24
Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . .24
XW-NAS5_FLPWXJ.book 4 ページ 2010年1月26日 火曜日 午後5時18分
Page: 4
Before you start 01
5
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 1:
Before you start
What’s in the box
Please confirm that the following accessories
are in the box when you open it.
• Remote control
• Remote control holder
• Lithium battery (CR2025)
• FM wire antenna
• Power cords x3
(Some models are not supplied with power
cord.)
• Operating instructions (This document)
Before using the remote control
The remote control is shipped already set in the
remote control holder.
The battery supplied with this unit is stored in
the battery casing.
• Remove the protective seal from the
battery casing.
When you notice a decrease in the operating
range, replace the battery (see below).
Replace the battery
When replacing the battery, use a
commercially available Lithium CR2025
battery.
1 Push the release tab to the left to open
the battery casing.
2 Pull out the battery casing.
3 Remove the battery from the casing.
4 Place a new battery in the casing.
Make sure the  side of the battery is facing
up when you place it in the space provided.
Caution
When using lithium batteries, please observe
the following:
• There is danger of explosion if the battery is
incorrectly replaced. Make sure to replace
only with the same or equivalent type
recommended by the manufacturer.
• Dispose of used battery cells immediately
after replacement. Keep away from
children.
• If swallowed, please contact a doctor
immediately.
• Lithium batteries may present a fire or
chemical burn hazard if misused. Do not
disassemble, heat above 100 °C, or
incinerate.
1
1
3
2
XW-NAS5_FLPWXJ.book 5 ページ 2010年1月26日 火曜日 午後5時18分
Page: 5
Before you start
01
6
En
• Remove the battery if the unit isn’t going to
be used for a month or more.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
• WARNING
Do not use or store batteries in direct
sunlight or other excessively hot place,
such as inside a car or near a heater. This
can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the
life or performance of batteries.
Using the remote control
The remote has a range of about 7 m at an
angle of about 30º from the remote sensor.
Keep in mind the following when using the
remote control:
• Make sure that there are no obstacles
between the remote and the remote sensor
on the unit.
• Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
• Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this unit.
• Replace the batteries when you notice a fall
off in the operating range of the remote.
Installing the unit
• When installing this unit, make sure to put
it on a level and stable surface.
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that
gives off a magnetic field). This may interfere
with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as
a kitchen)
Plugging in
After you’ve finished making all connections,
plug the unit into an AC outlet. The type of cord
which can be used depends on the power
voltage in each region or country. Please make
sure you use the correct cord due to the
possibility of fire or other hazard if used
incorrectly (see below).
1 Plug the supplied power cord into the AC
IN socket on the back of the unit.
2 Plug the other end into a power outlet.
Important
• Before making or changing any
connections, switch off the power and
disconnect the power cord from the AC
outlet.
AC power cord use
Region Plug type
For Taiwan exclusively
Caution
For use in Taiwan only. In
other areas, please do
not use. Taiwanese two-pin flat-
bladed plug
For Australian and New
Zealand exclusively
AS 3112 flat two-pin plug
For Others
European two-pin plug
XW-NAS5_FLPWXJ.book 6 ページ 2010年1月26日 火曜日 午後5時18分
Page: 6
Controls and displays 02
7
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 2:
Controls and displays
Remote control
1  STANDBY/ON
Switches the unit between standby and on.
2 Soundscape function/operation buttons
Use to turn the Soundscape (environmental
sound) function ON/OFF, and to switch
between settings (page 18).
3 PRESET +/–, Playback control buttons
Use to select preset radio stations (page 17).
Use when operating an iPod or Bluetooth
wireless technology device with this remote
control (page 11, 15).
4 BASS/TREBLE
Use the bass and treble controls to adjust the
overall tone.
5 SLEEP
Use to put the unit in sleep mode and
select the amount of time before sleep
(page 21).
WAKE UP
Use to turn the wake-up timer function ON/
OFF (page 21).
CLOCK
Use to switch the clock display functions
(page 20).
6 SETUP
Press to make various settings.
7 INPUT
Use to select an input source. Press repeatedly
to switch between iPod, tuner, Bluetooth
ADAPTER1
and external input.
8 VOLUME +/–
Use to set the listening volume.
9 ENTER
10 TUNE +/–
Use to find radio frequencies (page 17).
TUNER PRESET
Use to store preset radio stations in
memory, and to call them from memory
(page 17).
STANDBY/ON
INPUT
VOLUME
SOUND
SCAPE
SELECT
PRESET
MIX BALANCE
ON/
OFF
PRESET
ENTER
SLEEP
CLOCK SETUP
WAKE
UP
TUNER
PRESET
BASS/
TREBLE
TUNE
TUNE
1
2
3
4
5
6
7
8
9
10
Note
1 When the Bluetooth ADAPTER is not plugged in the ADAPTER PORT, cannot be selected even if INPUT is pressed.
XW-NAS5_FLPWXJ.book 7 ページ 2010年1月26日 火曜日 午後5時18分
Page: 7
Controls and displays
02
8
En
Front /top panel
1 Speaker units
2 iPod connector port
3  STANDBY/ON
Switches the unit between standby and on.
4 Power indicator
5 INPUT SELECTOR
Use to select an input source. Press repeatedly
to switch between iPod, tuner, Bluetooth
ADAPTER1
and external input.
6 VOLUME +/–
Use to set the listening volume.
7 Timer indicator
8 Remote sensor
9 Character display
10 Tuner indicator
1 2
10
7
STANDBY/ON INPUT SELECTOR
VOLUME
3 4 5 6
8
9
Note
1 When the Bluetooth ADAPTER is not plugged in the ADAPTER PORT, cannot be selected even if INPUT is pressed.
XW-NAS5_FLPWXJ.book 8 ページ 2010年1月26日 火曜日 午後5時18分
Page: 8
iPod playback 03
9
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 3:
iPod playback
Merely by connecting your iPod to this speaker
system, you can enjoy high-quality digital
sound direct from your iPod. These speakers
can also be connected to a television set,
letting you view images from your iPod.
Playback and volume level setting for iPod
music and images can be performed from this
unit or the iPod itself.
Confirm what iPod models are
supported
This system is compatible with the audio and
video of the iPod nano third generation and
above, iPod classic, iPod touch and iPhone. It
also supports audio playback on the iPod nano
second generation.1
Always use the most recent version of iPod
software available. Operation compatibility
may vary depending on the version of the
software used. You can confirm your software
version by operating your iPod as follows:
1 Select ‘Settings’ from the top menu.
2 Select ‘About’.
The software version will be displayed.
• Consult the Apple website regarding the
newest software versions and instructions
on how to update your version.
Tip
• When using an iPod not supported by this
unit, use a commercially available cable to
connect the iPod to the AUDIO IN
connector of this unit.
Connecting your iPod
Caution
• To prevent damage when connecting an
iPod, always use the Dock adaptor
supplied with your iPod, or a commercially
purchased Dock adaptor designed for your
iPod model.
Note
1 • Some functions may be restricted depending on the model or software version.
• iPod is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.
• Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizer off before
connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience
or loss of recorded material resulting from the iPod failure.
• When connecting an iPod, use the ‘Speaker’ menu’s ‘Backlight’ item to set the iPod’s backlight function. This does not apply
to iPod touch and iPhone.
MENU



iPod
Dock adaptor
XW-NAS5_FLPWXJ.book 9 ページ 2010年1月26日 火曜日 午後5時18分
Page: 9
iPod playback
03
10
En
1 Attach the Dock adaptor to iPod
connector port on the top panel of this unit.
• An iPod Dock adaptor is not supplied with
this unit.
When attaching the Dock adaptor, be sure to
orient the front-back directions of the Dock
adaptor correctly. To attach, first place the
protruding tabs on the front side of the adaptor
into the depressions on the iPod connector
port and press into position. When attaching
the adaptor, be careful not to strike the
connectors.
2 Connect your iPod.
Connecting your TV
To watch iPod images on a television, perform
connections using either a composite video
cable or component video cable.
• When using a component video cable for
connections, it is necessary to adjust the
unit’s video output. See Setting the video
output below.
• When an iPod is connected to this unit, the
iPod’s TV output setting is automatically
set to ON. While connected, the iPod can
be used to switch the TV output setting.1
Caution
• Before making or changing the
connections, switch off the power and
disconnect the power cord from the power
outlet. Plugging in should be the final step.
Setting the video output
Adjust the video output on this unit in
accordance with the method used to connect
the television.2
• Default setting: (Composite)
1 Switch the unit into standby.
2 Press SETUP.
3 Use / to select ‘ ’, then press
ENTER.
Note
1 • This function is limited to iPod models providing TV output settings.
• When the iPod is disconnected from this unit, the iPod’s TV output setting returns to its original state.
2 • Stop the iPod’s video playback before adjusting the video output setting. The setting mode is disabled during playback and
pause.
• During the video output setting process, if no button operation is performed for 3 minutes, the setting will be canceled and
power will return to the standby mode.
COMPONENTVIDEO
MONITOR OUT VIDEO 1
VIDEO 2
ADAPTER PORT
Y PB PR AUDIO IN
Component
video cable
(commercially
available)
TV
Composite
video cable
(commercially
available)
PRESET PRESET
ENTER
SLEEP
CLOCK SETUP
WAKE
UP
TUNER
PRESET
BASS/
TREBLE
TUNE
TUNE
XW-NAS5_FLPWXJ.book 10 ページ 2010年1月26日 火曜日 午後5時18分
Page: 10
iPod playback 03
11
En
English
Français
Deutsch
Nederlands
Italiano
Español
4 Use / to select the video output
setting.
• – The video output will switch to
Composite.
• – The video output will switch to
Component.
5 Press ENTER.
The setting will be completed, and the display
for the newly set value will flash for three
seconds, after which the power will once again
switch to standby mode.
Playing your iPod
Caution
• When your iPod is connected to this unit
and you wish to operate the iPod by
touching it directly, be sure to hold the iPod
steady with the other hand to prevent
malfunctions due to faulty contacts.
When an iPod is connected to this unit,
will flash while the unit confirms the iPod
connection and retrieves data from the iPod.
When INPUT is pressed to change the input to
iPod, the connection is completed and
will light steadily.1
Playback and volume level setting for iPod
music and images can be performed from this
unit or the iPod itself.
• When using the iPod to adjust sound
volume, the adjustment will be applied only
to the sound produced from this unit’s
speakers.2
If the iPod is disconnected from
this unit, the iPod’s sound volume will
return to its original setting.
The following operations are possible for iPod,
using the remote control.
Using the tone controls
Adjust the sound tone. Adjustment is
performed from the iPod’s screen.2 The
settings performed here are reflected in the
BASS/TREBLE settings on this unit.
iPod nano or iPod classic:
1 Select ‘Speaker’ from the top menu.
2 Select ‘Tone control’.
3 Select a setting.
iPod touch or iPhone3
:
1 Select ‘Settings’ from the home menu.
2 Select ‘Speaker’.
3 Select ‘Tone control’.
4 Select a setting.
Select one of the following:
• Flat – Revert sound to its natural state.
• Bass ON – Emphasize bass sound.
• Treble ON – Emphasize treble sound.
• Bass/Treble ON – Emphasizes bass and
treble sounds.
Note
1 If an iPod is connected when this unit is in standby mode, the power will turn on and iPod input will be selected automatically.
2 These adjustments are applied to all inputs to the unit.
Button What it does
/ Starts normal playback and pauses/
unpauses playback.
 Press to skip to the start of the current
file, then previous files. Press and hold
to start fast reverse scanning.
 Press to skip to the next file. Press and
hold to start fast forward scanning.
VOLUME
+/–
Use to set the listening volume.
3 This setting may not be supported, depending on the iPod touch or iPhone software version.
XW-NAS5_FLPWXJ.book 11 ページ 2010年1月26日 火曜日 午後5時18分
Page: 11
iPod playback
03
12
En
Important
If an error message lights in the front panel, try
following the points below:
If the iPod cannot be operated, check the
following items:
• Is the iPod connected correctly?
Reconnect the iPod to the unit.
• Is the iPod experiencing a hangup? Try
resetting the iPod, and reconnect it to the
unit.
Tip
• iPod recharging occurs whenever an iPod
is connected to this unit. (This function is
supported in standby mode as well.)
• Whenever an iPod is connected to this
unit, turning the unit’s power ON or
switching input to iPod will cause iPod
playback to begin automatically.
• When input is switched from iPod to
another function, the iPod playback stops
automatically.
• If the unit is set to standby when an iPod is
connected, the iPod’s power will be turned
OFF automatically.
Message What it means
There is a problem with the signal
path from the iPod to the unit.
Reconnect the iPod to the unit. If this
doesn’t seem to work, try resetting
your iPod.
An unsupported device has been
connected. Check whether the iPod
was supported by this unit.
The iPod that is not supported is
connected. Check whether the iPod
was supported by this unit (page 9).
When the iPod software version is
too old, update the iPod software to
the latest version.
When there is no response from the
iPod, update the iPod software to the
latest version. If this doesn’t seem to
work, try resetting your iPod.
XW-NAS5_FLPWXJ.book 12 ページ 2010年1月26日 火曜日 午後5時18分
Page: 12
Bluetooth® ADAPTER for Wireless Enjoyment of Music 04
13
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 4:
Bluetooth®
ADAPTER for
Wireless Enjoyment of Music
Wireless music play
When the Bluetooth ADAPTER (Pioneer Model
No. AS-BT100) is connected to this unit, a
product equipped with Bluetooth wireless
technology (portable cell phone, digital music
player, etc.) can be used to listen to music
wirelessly.1 Also, by using a commercially
available transmitter supporting Bluetooth
wireless technology, you can listen to music on
a device not equipped with Bluetooth wireless
technology. The AS-BT100 model supports
SCMS-T contents protection, so music can
also be enjoyed on devices equipped with
SCMS-T type Bluetooth wireless technology.
Remote control operation
The remote control supplied with this unit
allows you to play and stop media, and perform
other operations.2
Connecting Optional Bluetooth
ADAPTER
• Before making or changing the
connections, switch off the power and
disconnect the power cord from the AC
outlet.
Remote control operation
This unit
Bluetooth®
ADAPTER
Device not equipped with
Bluetooth wireless technology:
Digital music player
+
Bluetooth audio transmitter (sold
commercially)
Bluetooth wireless technology
enabled device:
Digital music player
Bluetooth wireless
technology enabled device:
Cell phone
Note
1 • It must be necessary that the Bluetooth wireless technology enabled device supports A2DP profiles.
• Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology enabled
devices.
2 • It must be necessary that the Bluetooth wireless technology enabled device supports AVRCP profiles.
• Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.
COMPONENTVIDEO
MONITOR OUT VIDEO 1
VIDEO 2
ADAPTER PORT
Y PB PR
Bluetooth®
ADAPTER
XW-NAS5_FLPWXJ.book 13 ページ 2010年1月26日 火曜日 午後5時18分
Page: 13
Bluetooth® ADAPTER for Wireless Enjoyment of Music
04
14
En
1 Switch the unit into standby and connect
Bluetooth ADAPTER to the ADAPTER PORT
located in the rear panel.
2 Press  STANDBY/ON.
3 Press INPUT to switch the unit to ‘ ’.1
When pairing has not been performed,
‘ ’ is displayed.
Setting the PIN code
Set this unit’s PIN code to the same setting as
that for the Bluetooth wireless technology
device used. Supported PIN code setting
values include 0000, 1234 or 8888.
• Default setting: 0000
1 Switch the unit into standby.
2 Press and hold  for three seconds.
The new PIN code will be displayed, indicating
that the PIN code has been changed.
Repeat step 2 until the PIN code is reset to the
value desired.
Pairing Bluetooth ADAPTER and
Bluetooth wireless technology
device
“Pairing” must be done before you start
playback of Bluetooth wireless technology
content using Bluetooth ADAPTER. Make sure
to perform pairing first time you operate the
system or any time pairing data is cleared.
“Pairing” is the step necessary to register
Bluetooth wireless technology device to enable
Bluetooth communications.2
For more details,
see also the operating instructions of your
Bluetooth wireless technology device.
1 When ‘ ’ lights, press .
‘ ’ will flash, and the unit will enter the
pairing standby mode.
2 Switch on the Bluetooth wireless
technology device that you want to make
pairing, place it near the system and set it
into the pairing mode.
Pairing begins.
3 Check to see that the Bluetooth ADAPTER
is detected by the Bluetooth wireless
technology device.
lights when Bluetooth wireless
technology device is connected.
lights when Bluetooth wireless
technology device is not connected. In this
case, perform the connection operation from
the side of the Bluetooth wireless technology
device.
Note
1 When the Bluetooth ADAPTER is not plugged in the ADAPTER PORT, cannot be selected even if INPUT is pressed.
PRESET PRESET
ENTER
SLEEP WAKE
UP
BASS/
TREBLE
TUNE
2 • Pairing is required when you first use Bluetooth wireless technology device and Bluetooth ADAPTER.
• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology
device.
PRESET PRESET
ENTER
SLEEP WAKE
UP
BASS/
TREBLE
TUNE
XW-NAS5_FLPWXJ.book 14 ページ 2010年1月26日 火曜日 午後5時18分
Page: 14
Bluetooth® ADAPTER for Wireless Enjoyment of Music 04
15
En
English
Français
Deutsch
Nederlands
Italiano
Español
Listening to Music Contents of
Bluetooth wireless technology
device with Your System
1 Press INPUT to switch the unit to ‘ ’.
2 Connect the Bluetooth wireless
technology device to the Bluetooth
ADAPTER.
3 Start playback of music contents stored in
Bluetooth wireless technology device.
The following operations are now possible for
Bluetooth wireless technology devices, using
the remote control.1
Button What it does
/ Starts normal playback and pauses/
unpauses playback.
 Press to skip to the start of the current
file, then previous files. Press and hold
to start fast reverse scanning.
 Press to skip to the next file. Press and
hold to start fast forward scanning.
VOLUME
+/–
Use to set the listening volume.
Note
1 • Bluetooth wireless technology device should be compatible with AVRCP profile.
• Depending on Bluetooth wireless technology device you use, operation may differ from what is shown in this table.
XW-NAS5_FLPWXJ.book 15 ページ 2010年1月26日 火曜日 午後5時18分
Page: 15
Other connections
05
16
En
Chapter 5:
Other connections
• Before making or changing the
connections, switch off the power and
disconnect the power cord from the AC
outlet.
Connecting auxiliary
components
Connect the rear panel AUDIO IN mini-plug
jack to your auxiliary playback component.
• This method can be used to play music on
this unit from iPods that do not support use
of an iPod Dock.
• Press INPUT to switch the unit to ‘ ’.
COMPONENTVIDEO
MONITOR OUT VIDEO 1
VIDEO 2
Y PB PR AUDIO IN
AC IN
Digital audio
player, etc.
XW-NAS5_FLPWXJ.book 16 ページ 2010年1月26日 火曜日 午後5時18分
Page: 16
Using the tuner 06
17
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 6:
Using the tuner
Connect the FM antenna
Connect the FM antenna plug onto the center pin
of the FM antenna socket.1
Listening to the FM radio
The tuner can receive FM broadcasts, and lets
you memorize your favorite stations so you
don’t have to manually tune in every time you
want to listen.
1 Press INPUT to switch to the tuner.
The tuner indicator will light, and the tuned
frequency will be displayed.
2 Tune to a station.
There are three ways to do this:
Automatic tuning – To search for
stations, press and hold TUNE +/– for
about a second. The system will start
searching for the next station, stopping
when it has found one. Repeat to search
for other stations.
Manual tuning – To change the frequency
one step at a time, press TUNE +/–.
High speed tuning – Press and hold
TUNE +/– for high speed tuning. Release
the button at the frequency you want.
Memorizing stations
You can save up to 10 station presets so that
you always have easy access to your favorite
stations without having to tune in manually
each time.2
1 Press INPUT to switch to the tuner.
2 Tune to an FM radio station.
3 Press TUNER PRESET.
4 Use TUNE +/– to select the station preset
you want (e.g., ‘ ’) then press ENTER.
Listening to station presets
1 Press INPUT to switch to the tuner.
2 Use PRESET +/– to select a station preset.
Note
1 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit.
AC IN
FM UNBAL 75
ANTENNA
FM wire antenna
STANDBY/ON
INPUT
PRESET PRESET
ENTER
SLEEP
CLOCK SETUP
WAKE
UP
TUNER
PRESET
BASS/
TREBLE
TUNE
TUNE
2 When a new broadcast frequency is stored in a station containing a previously stored frequency, the previous frequency will
be overwritten with the new one.
XW-NAS5_FLPWXJ.book 17 ページ 2010年1月26日 火曜日 午後5時18分
Page: 17
Sound settings
07
18
En
Chapter 7:
Sound settings
Using the Soundscape
The Soundscape function lets you add a variety
of environmental sounds to the music you
play.1
• Press SOUNDSCAPE ON/OFF.
The Soundscape function is activated and
environmental sounds are added to your music
playback. The display ‘ ’ indicates the
type of environmental sound selected.
• The Soundscape function alternates ON/
OFF each time the SOUNDSCAPE ON/OFF
button is pressed.
Adjust the Soundscape volume
• Default setting: 05
• Use MIX BALANCE +/– to adjust the
balance between music and Soundscape
effects.
Adjustment can be made between values 00
and 10. Press “+” to increase the volume of
Soundscape environmental sounds and press
“–” to reduce the volume of Soundscape
environmental sounds and increase the
volume of music.
Select the type of environmental
sound
• With the Soundscape function ON, press
SELECT / to choose a desired
environmental sound.
Select one of the following 6 types:
• – The sound of waves at Rio de
Janeiro’s Copacabana. Enjoy the sound of
high surf.
The sound of high surf interspersed with
voices on the beach.
• – European street sounds. Enjoy
the sounds of a sidewalk café on a street
somewhere in Europe.
Cars pass along a flagstone road, mixed
with the sounds of passersby.
• – Coral reef in the tropics. Enjoy
the sound of gentle waves.
Blue sea in Japan’s Okinawa Island. Clear
waves gently roll onto the white sands of a
broken-coral reef.
• – A small forest stream and small
birds. Enjoy the sounds of early morning
alongside a stream flowing through a
forest, together with the chirping of small
wild birds.
• – Walk through a high meadow in
fall. Enjoy sounds of small birds and
footsteps on fallen leaves.
A fall meadow in Nagano, Japan.
Note
1 If desired, you can choose to listen to Soundscape environmental sounds alone, without mixing with music.
VOLUME
SOUND
SCAPE
SELECT MIX BALANCE
ON/
OFF
XW-NAS5_FLPWXJ.book 18 ページ 2010年1月26日 火曜日 午後5時18分
Page: 18
Sound settings 07
19
En
English
Français
Deutsch
Nederlands
Italiano
Español
• – Vinyl record sounds. Enjoy the
sound of scratches and hisses from a vinyl
record mixed with music from iPod, radio
tuner, or other external input source. (Even
greater effect is achieved when combined
with Low Fidelity sound mode.)
When mixed with music, even new tracks
produce a retro feel like looking at a sepia-
toned photograph.
Using the sound effects
You can add exciting effects to audio sources.
• Default setting: (OFF)
1 Press SETUP.
2 Use / to select ‘ ’, then press
ENTER.
3 Use / to switch Sound modes, then
press ENTER.
• (Auto Level Control) – This unit
equalizes playback sound levels.
• (Low Fidelity) – Produces a retro-feel
to music play.
• (Vivid) – Produces a sharpened
effect similar to that experienced at a live
concert.
• (OFF) – Revert sound to its natural state.
Adjusting the bass and treble
Use the bass and treble controls to adjust the
overall tone.
1 Press BASS/TREBLE.
2 Use / to select ‘ ’ (Bass) or
‘ ’ (Treble), then press ENTER.
3 Use / to adjust the bass or treble, then
press ENTER.
You can adjust low and high sounds on a scale
of –6 to +6.
Using the Sound Retriever
When audio data is removed during the WMA/
MP3/MPEG-4 AAC compression process,
sound quality often suffers from an uneven
sound image. The Sound Retriever feature
employs new DSP technology that helps bring
CD quality sound back to compressed by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
• Default setting: (ON)
1 Switch the unit into standby.
2 Press SETUP.
3 Use / to select ‘ ’, then press
ENTER.
4 Use / to switch the sound retriever on
or off.
5 Press ENTER.
When the setting is completed, the newly set
value flashes for 3 seconds, then the power
returns to standby mode.
PRESET PRESET
ENTER
SLEEP
CLOCK SETUP
WAKE
UP
TUNER
PRESET
BASS/
TREBLE
TUNE
TUNE
XW-NAS5_FLPWXJ.book 19 ページ 2010年1月26日 火曜日 午後5時18分
Page: 19
Using the timer
08
20
En
Chapter 8:
Using the timer
Setting the clock
Setting the clock allows you to use the timer.1
1 Switch the unit into standby.
2 Press SETUP.
3 Use / to select ‘ ’, then press
ENTER.
The current time is displayed.
4 Use / to set the hour, then press
ENTER.
5 Use / to set the minute, then press
ENTER.
When the setting is completed, the newly set
value flashes for 3 seconds, then the power
returns to standby mode.
Display mode setting
Use to switch the display mode (clock display,
etc.)
1 With the power turned ON, press SETUP.
2 Use / to select ‘ ’, then press
ENTER.
The current time is displayed.
3 Use / to select display setting, then
press ENTER.
• – Display is turned off except when
entering commands.2
• – Clock display appears except
when entering commands.
• – Displays values constantly except
when entering commands. When power is
on standby mode, displays clock.2
Changing the clock’s display mode
You can choose to display the clock in 12-hour
mode or 24-hour mode.
• Default setting: (24-hour mode)
1 Switch the unit into standby.
2 Press SETUP.
3 Use / to select ‘ ’ then press
ENTER.
4 Use / to select ‘ ’ or ‘ ’ then
press ENTER.
When the setting is completed, the newly set
value flashes for 3 seconds, then the power
returns to standby mode.
Setting the wake-up timer
Use the wake-up timer to set the unit to switch
on at any time and start playing whatever
source you want.
If iPod is selected as the timer sound, when the
wake-up timer operates, the iPod’s power will
automatically turn ON and playback will begin.
Note
1 You’ll need to set the clock again if you unplug the unit (or in case of a power failure).
PRESET PRESET
ENTER
SLEEP
CLOCK SETUP
WAKE
UP
TUNER
PRESET
BASS/
TREBLE
TUNE
TUNE
2 When power is ON or in standby mode, the current time can be checked by pressing the CLOCK button.
XW-NAS5_FLPWXJ.book 20 ページ 2010年1月26日 火曜日 午後5時18分
Page: 20
Using the timer 08
21
En
English
Français
Deutsch
Nederlands
Italiano
Español
1 With input set to iPod or tuner, press
SETUP.
2 Use / to select ‘ ’, then press
ENTER.
Timer setting time is displayed.
3 Set the desired time for the timer.
Use / to set the hour, then press ENTER.
Set the minute in the same way, pressing
ENTER when you’re done.
4 Use / to select the input source to be
used as the timer sound, then press ENTER.
While selecting the input source, the sound
from that source will be audible (except when
beep is selected). Use the VOLUME +/–
buttons to adjust the sound volume.
• If is selected, an electronic tone will
sound.
5 Use / to set the snooze function to
ON/OFF as desired, then press ENTER.
The timer time, input setting, snooze setting,
and volume setting will be displayed in order,
thus completing the wake-up timer setting.
• The timer indicator lights.
When the wake-up timer sounds
If the snooze function is OFF:
Press the main unit’s  STANDBY/ON button
to stop the timer playback and turn power off.
Alternately, wait for one hour (when beep is
selected, wait for one minute) and playback will
stop automatically and power will turn off.
If any other button is pressed, the timer
playback stops and normal playback of the
currently selected input source will begin.
• When finished using the timer, set the
timer function to OFF (see below).
If the snooze function is ON:
Press the main unit’s  STANDBY/ON button
to stop the timer playback and turn power off.
If any other button is pressed or playback
continues for one minute, the timer sound will
stop, but the snooze function will operate and
five minutes later the timer sound will playback
again.
• While the snooze function is operating, no
buttons can be used other than WAKE UP
and the main unit’s  STANDBY/ON. (To
turn the timer function OFF, press the
WAKE UP button two times.)
• The snooze function repeats up to five
times. After that, the unit’s power turns off
automatically.
• When finished using the timer, set the
timer function to OFF (see below).
Turning the wake-up timer on/off
• Press WAKE UP.
Each time the button is pressed, the timer
function switches alternately to ON/OFF.
• When the timer is set to ON, the timer
indicator lights.
Using the sleep timer
The sleep timer switches off the unit after a
specified time so you can fall asleep without
worrying about it.
• Press SLEEP repeatedly to select a switch-
off time.
Choose between 5 min, 15 min, 30 min, 60 min,
90 min or Off.
• The remaining time is displayed while the
sleep timer operates.1
Note
1 The sleep timer can be reset by pressing the SLEEP button while the sleep timer is operating.
XW-NAS5_FLPWXJ.book 21 ページ 2010年1月26日 火曜日 午後5時18分
Page: 21
Additional information
09
22
En
Chapter 9:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect
the power plug from the outlet and insert again to return to normal operating conditions.
Problem Remedy
The power does not turn on. • Disconnect the power plug from the outlet, and insert again.
• If the power shuts off automatically, take the unit to your nearest
Pioneer authorized service center or your dealer for servicing.
Power automatically switches
to standby without user action.
• When input is set to iPod, if no iPod is connected for one hour or
more, the unit’s power automatically turns OFF.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to
Connecting auxiliary components on page 16).
Can’t operate the remote
control.
• Replace the battery (refer to page 5).
• Operate within 7 m, 30° of the remote sensor on the front panel
(refer to page 6).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
Considerable noise in radio
broadcasts.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall. You may also connect an outdoor FM antenna.
• Turn off any other equipment that may be causing the noise or
move it away from the unit.
Auto tuning does not pick up
some stations.
• The radio signal is weak. Auto tuning will only detect radio stations
with a good signal. For more sensitive tuning, connect an outdoor
antenna.
XW-NAS5_FLPWXJ.book 22 ページ 2010年1月26日 火曜日 午後5時18分
Page: 22
Additional information 09
23
En
English
Français
Deutsch
Nederlands
Italiano
Español
Resetting the system
Use this procedure to reset all system settings
to the factory default.
• When performing reset, first disconnect all
components connected to this unit.
1 Switch the unit on.
2 Press and hold VOLUME – on the top
panel, and then press and hold  STANDBY/
ON for three seconds.
Power is set to standby mode.
The next time you switch on, all the system
settings should be reset.
About iPod/iPhone
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by the
developer to meet Apple performance standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries. iPhone is a
trademark of Apple Inc.
The Bluetooth wireless
technology device cannot be
connected or operated. Sound
from the Bluetooth wireless
technology device is not
emitted or the sound is
interrupted.
• Check that no object that emits electromagnetic waves in the 2.4
GHz band (microwave oven, wireless LAN device or Bluetooth
wireless technology apparatus) is near the unit. If such an object is
near the unit, set the unit far from it. Or, stop using the object
emitting the electromagnetic waves.
• Check that the Bluetooth wireless technology device is not too far
from the unit and that obstructions are not set between the Bluetooth
wireless technology device and the unit. Set the Bluetooth wireless
technology device and the unit so that the distance between them is
less than about 10 m and no obstructions exist between them.
• Check that the Bluetooth ADAPTER and the ADAPTER PORT of the
unit are correctly connected.
• The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless technology.
Check the setting of the Bluetooth wireless technology device.
• Check that pairing is correct. The pairing setting was deleted from
this unit or the Bluetooth wireless technology device. Reset the
pairing.
• Check that the profile is correct. Use a Bluetooth wireless
technology device that supports A2DP profile and AVRCP profile.
Problem Remedy
XW-NAS5_FLPWXJ.book 23 ページ 2010年1月26日 火曜日 午後5時18分
Page: 23
Additional information
09
24
En
Specifications
• Amplifier section
RMS Power Output:
Front Left/Right. . . . . . . . . . . . . . . 15 W + 15 W
(1 kHz, 10 %, T.H.D., 8 Ω)
Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . .30 W
(100 Hz, 10 %, T.H.D., 4 Ω)
• Speaker section
Enclosure. . . Bass-reflex (magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . . .3-way system
Speakers:
Subwoofer . . . . . . . . . . . . . . . . . . . . 10 cm cone
Mid/Tweeter. . . . . . . . . . . . . . . . . . 5.2 cm cone/
2.6 cm semi-dome
Frequency range . . . . . . . . . . . . . . 50 Hz to 30 kHz
• Miscellaneous
Power requirements
. . . . . . . . . . . . . . . AC 110 V to 240 V, 50 Hz/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . .30 W
In standby . . . . 1.0 W (Clock/Wake-up timer ON)
0.5 W (Clock/Wake-up timer OFF)
Dimensions
. . . . . . . 420 mm (W) x 148 mm (H) x 210 mm (D)
Weight (without package) . . . . . . . . . . . . . . 5.0 kg
• Accessories
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control holder . . . . . . . . . . . . . . . . . . . . . 1
Lithium battery (CR2025) . . . . . . . . . . . . . . . . . . . 1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating instructions (This document)
*Some models are not supplied with power
cord.
Note
• Specifications and the design are subject
to possible modifications without notice,
due to improvements.
Cleaning the unit
• Use a polishing cloth or dry cloth to wipe
off dust and dirt.
• When the surface is dirty, wipe with a soft
cloth dipped in some neutral cleanser
diluted five or six times with water, and
wrung out well, and then wipe again with a
dry cloth. Do not use furniture wax or
cleansers.
• Never use thinners, benzine, insecticide
sprays or other chemicals on or near this
unit, since these will corrode the surface.
Published by Pioneer Corporation.
Copyright © 2010 Pioneer Corporation.
All rights reserved.
XW-NAS5_FLPWXJ.book 24 ページ 2010年1月26日 火曜日 午後5時18分
Page: 24
Additional information 09
25
En
English
Français
Deutsch
Nederlands
Italiano
Español
XW-NAS5_FLPWXJ.book 25 ページ 2010年1月26日 火曜日 午後5時18分
Page: 72
其他資訊 09
25
Zhtw
English
Français
Deutsch
Nederlands
Italiano
Español
English
XW-NAS5_FLPWXJ_zhtw.book 25 ページ 2010年1月26日 火曜日 午後5時45分
Page: 75
<ARE7657-A>
Published by Pioneer Corporation.
Copyright © 2010 Pioneer Corporation.
All rights reserved.
Printed in
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B1_En
XW-NAS5_FLPWXJ.book 25 ページ 2010年1月26日 火曜日 午後5時18分

Question & answers

There are no questions about the Pioneer XW-NAS5 yet.

Ask a question about the Pioneer XW-NAS5

Have a question about the Pioneer XW-NAS5 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer XW-NAS5. Please make sure that you describe your difficulty with the Pioneer XW-NAS5 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.