Pioneer XN-P02-K manual

View a manual of the Pioneer XN-P02-K below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Audio Streamer
  • Model/name: XN-P02-K
  • Filetype: PDF
  • Available languages: English, Dutch, German, French, Spanish, Italian, Russian

Table of Contents

Page: 0
Operating Instructions
Discover the benefits of registering your product online at http://www.pioneer.co.uk (or http://www.pioneer.eu).
NETWORK RECEIVER
XN-P02-S/-K
N-P01-S/-K
XN-P02DAB-S/-K
NETWORK AUDIO PLAYER
Page: 1
2
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. D3-4-2-1-1_B1_En
WARNING
This equipment is not waterproof. To prevent a fire or shock
hazard, do not place any container filled with liquid near this
equipment (such as a vase or flower pot) or expose it to
dripping, splashing, rain or moisture.
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame sources
(such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
(XN-P02, XN-P02DAB only)
When installing this unit, make sure to leave space around
the unit for ventilation to improve heat radiation (at least 10
cm at top, 10 cm at rear, and 10 cm at each side).
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling
vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).
D3-4-2-1-7c*_A2_En
CAUTION
The  STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet. Since the
power cord serves as the main disconnect device for the
unit, you will need to unplug it from the AC outlet to shut
down all power. Therefore, make sure the unit has been
installed so that the power cord can be easily unplugged
from the AC outlet in case of an accident. To avoid fire
hazard, the power cord should also be unplugged from the
AC outlet when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
WARNING
Store small parts out of the reach of children and infants. If
accidentally swallowed, contact a doctor immediately.
D41-6-4_A1_En
This product is for general household purposes. Any failure
due to use for other than household purposes (such as
long-term use for business purposes in a restaurant or use
in a car or ship) and which requires repair will be charged
for even during the warranty period.
K041_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by
tugging the cord and never touch the power cord when your
hands are wet as this could cause a short circuit or electric
shock. Do not place the unit, a piece of furniture, etc., on the
power cord, or pinch the cord. Never make a knot in the cord
or tie it with other cords. The power cords should be routed
such that they are not likely to be stepped on. A damaged
power cord can cause a fire or give you an electrical shock.
Check the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized service
center or your dealer for a replacement.
S002*_A1_En
10 cm 10 cm
10 cm
10 cm
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
D3-11-15-5-2_A1_En
For Norway customers
Utstyr som er koplet til beskyttelsesjord via nettplugg
og/eller via annet jordtilkoplet utstyr – og er tilkoplet et
kabel-TV nett, kan forårsake brannfare. For å unngå dette
skal det ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret og
kabel-TV nettet.
XN-P02, XN-P02DAB only
For Sweden customers
Utrustning som är kopplad till skyddsjord via jordat
vägguttag och/eller via annan utrustning och samtidigt är
kopplad till kabel-TV nät kan i vissa fall medföra risk för
brand.
För att undvika detta skall vid anslutning av utrustningen
till kabel-TV nät galvanisk isolator finnas mellan
utrustningen och kabel-TV nätet.
(N-P01 only)
When installing this unit, make sure to leave space around
the unit for ventilation to improve heat radiation (side 10 cm,
rear 10 cm, top 5 mm).
WARNING
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product, and to protect it
from overheating. To prevent fire hazard, the openings should
never be blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the equipment on thick
carpet or a bed.
D3-4-2-1-7b*_A1_En
Page: 2
3
Information for users on collection and disposal of old equipment and used batteries
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Symbol examples
for batteries
Symbol for
equipment
Pb
Do not lift this device by holding the wireless LAN antenna,
since damage or personal injury may result.
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a
band used by other wireless systems (Microwave ovens and
Cordless phones, etc.). In this event noise appears in your
television image, there is the possibility this unit (including
products supported by this unit) is causing signal interference
with the antenna input connector of your television, video,
satellite tuner, etc. In this event, increase the distance
between the antenna input connector and this unit (including
products supported by this unit).
• Pioneer is not responsible for any malfunction of the
compatible Pioneer product due to communication
error/malfunctions associated with your network
connection and/or your connected equipment. Please
contact your Internet service provider or network device
manufacturer.
• A separate contract with/payment to an Internet service
provider is required to use the Internet.
Page: 3
4
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly.
About this product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . 5
Loading the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating range of remote control . . . . . . . . . . . . . . . . . . . 5
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
01 Controls and displays
(Network audio player: N-P01)
Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
02 Connecting your equipment
(Network audio player: N-P01)
WLAN antenna connection . . . . . . . . . . . . . . . . . . . . . . . 11
Analog audio output connections. . . . . . . . . . . . . . . . . . . 11
Digital audio output connections . . . . . . . . . . . . . . . . . . . 11
Connecting USB storage devices . . . . . . . . . . . . . . . . . . . 12
Connecting to the network through the LAN interface or
WLAN antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using centralized control with other Pioneer
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using combined with the XC-P01 or XC-P01DAB . . . . . . . 13
Plugging in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
03 Getting started
(Network audio player: N-P01)
Setting the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
04 iPod/iPhone/iPad playback
(Network audio player: N-P01)
Confirming what iPod/iPhone/iPad models are
supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Playing your iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . 16
05 Music playback using Bluetooth® wireless
technology (Network audio player: N-P01)
Remote control operation. . . . . . . . . . . . . . . . . . . . . . . . . 17
Pairing with the unit (Initial registration) . . . . . . . . . . . . . 17
Listen to music on the unit from a Bluetooth
capable device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
06 USB playback (Network audio player: N-P01)
Playing files stored on USB storage devices. . . . . . . . . . . 20
07 Playback with NETWORK features
(Network audio player: N-P01)
Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
A: Wired setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
B: Connection settings using an iOS device
(with iOS 5.0 or later) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
C: Connection settings using an iOS device
(with iOS 7.1 or later) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
D: WPS connection setting. . . . . . . . . . . . . . . . . . . . . . . . 24
E: Wireless Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
F: Connecting to a router without WPS-PBC function. . . . 26
Friendly Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Listening to the Internet radio. . . . . . . . . . . . . . . . . . . . . . 27
Advanced operations for the Internet radio. . . . . . . . . . . . 27
About the Spotify audio stream playback function . . . . . . 28
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Playing audio files stored on computers or other
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using AirPlay to enjoy music . . . . . . . . . . . . . . . . . . . . . . 30
AirPlay Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installing Pioneer ControlApp. . . . . . . . . . . . . . . . . . . . . . 31
Using Pioneer ControlApp . . . . . . . . . . . . . . . . . . . . . . . . 31
08 Additional information
(Network audio player: N-P01)
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Setting quick start mode. . . . . . . . . . . . . . . . . . . . . . . . . . 34
Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Resetting this player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
About network playback . . . . . . . . . . . . . . . . . . . . . . . . . . 37
About playable music file formats. . . . . . . . . . . . . . . . . . . 38
About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . . . 39
About aptX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
About Wi-Fi® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
About Spotify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
09 Control and display
(Stereo receiver: SX-P01, SX-P01DAB)
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10 Connecting your equipment
(Stereo receiver: SX-P01, SX-P01DAB)
Connecting your equipments
(XN-P02, XN-P02DAB only) . . . . . . . . . . . . . . . . . . . . . . . . 42
11 Getting started
(Stereo receiver: SX-P01, SX-P01DAB)
To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Timer and sleep operation. . . . . . . . . . . . . . . . . . . . . . . . . 46
Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . . 46
Sleep operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
12 Using the tuner
(Stereo receiver: SX-P01, SX-P01DAB)
Tuning to a FM radio station . . . . . . . . . . . . . . . . . . . . . . . 47
Introduction to RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Listening to the DAB (XN-P02DAB only) . . . . . . . . . . . . . . 49
Selecting DAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13 Additional information
(Stereo receiver: SX-P01, SX-P01DAB)
Troubleshooting chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
If problem occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Factory reset, clearing all memory . . . . . . . . . . . . . . . . . . 51
Cleaning the cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Specifications (Network audio player: N-P01) . . . . . . . . . . 52
Specifications (Stereo receiver: SX-P01, SX-P01DAB) . . . . 52
Contents
Page: 4
5
Before you start
About this product
XN-P02 or XN-P02DAB
XN-P02 or XN-P02DAB Network Receiver System consists of
Stereo receiver and Network audio player.
N-P01
N-P01 Network Audio Player consists of the main unit.
Note
• The product may be used in conjunction with the following,
separately retailed system products. (N-P01 only)
CD RECEIVER SYSTEM XC-P01
• Stereo receiver: SX-P01
• CD Player: PD-P01
CD RECEIVER SYSTEM XC-P01DAB
• Stereo receiver: SX-P01DAB
• CD Player: PD-P01
Checking what’s in the box
Please check that you’ve received the following supplied
accessories:
• Remote control
• Power cord
• AAA size IEC R03 dry cell batteries (to confirm system
operation) x 2
• RCA audio cable
• WLAN antenna x 2
• Remote control cable
• Warranty card
• Quick Start Guide
• These operating instructions (CD-ROM)
• FM wire antenna (XN-P02 only)
• DAB/FM wire antenna (XN-P02DAB only)
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
Loading the batteries
The batteries included with the player have been provided to
allow you check product operation and may not last long. We
recommend using alkaline batteries that have a longer life.
WARNING
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a heater.
This can cause batteries to leak, overheat, explode or catch
fire. It can also reduce the life or performance of batteries.
CAUTION
• Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
- Never use new and old batteries together.
- Insert the plus and minus sides of the batteries properly
according to the marks in the battery case.
- Batteries with the same shape may have different
voltages. Do not use different batteries together.
- When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
- When inserting the batteries, make sure not to damage
the springs on the battery’s  terminals. This can cause
batteries to leak or over heat.
Operating range of remote control
The remote has a range of about 7 m at an angle of about 30°
from the remote sensor.
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote
and the remote sensor on the player.
• Remote operation may become unreliable if strong sunlight
or fluorescent light is shining on the player’s remote sensor.
• Remote controllers for different devices can interfere with
each other. Avoid using remotes for other equipment
located close to this player.
• Replace the batteries when you notice a fall off in the
operating range of the remote.
7 m
30°
30°
Stereo receiver:
SX-P01/SX-P01DAB
Network audio player:
N-P01
Page: 5
6
Remote control
There are functions which can be operated only when the remote control is set in either of the network audio player control mode, stereo receiver control mode or CD player control mode, and
functions which can be operated regardless of the mode of the remote control.
Buttons for general operations
The following functions are available regardless of the mode
of the remote control.
1 SYSTEM ON
Press to turn on the stereo receiver, network audio player and
CD player (page 44).
2 STANDBY/ON
RECEIVER – Press to turn on and off the stereo receiver
(page 44).
CD – Press to turn on and off the CD player.
NETWORK – Press to turn on and off the network audio
player (page 21).
3 SYSTEM OFF
Press to turn off the stereo receiver, network audio player and
CD player (page 44).
4 Remote control mode selection buttons
CONTROL RCV – Press to operate the functions available
only in the stereo receiver control mode.
CONTROL CD – Press to operate the functions available
only in the CD player control mode.
CONTROL NET – Press to operate the functions available
only in the network audio player control mode.
<Stereo receiver SX-P01, SX-P01DAB only>
5 Input function buttons
Use to select the input source to this receiver (page 45).
6 DIRECT
Use to listen to the sound source in the original sound quality
(page 45).
7 TREBLE +/–
Press to adjust the treble (page 45).
8 BASS +/–
Press to adjust the bass (page 45).
9 SLEEP
Press to select the amount of time before the stereo receiver
turn off (Off – 30 min. – 60 min. – 90 min.). You can check
the remaining time by pressing SLEEP once (page 46).
10 CLOCK
Press to check the current time (page 44).
11 Volume control buttons
Use to adjust the listening volume (page 44).
12 MUTE
Use to Mute the volume (page 45).
<CD player PD-P01 only>
13 CD USB
Press to select the CD or iPod/USB function for the CD
player.
Note
• The supplied remote control can be used to control the
network audio player (N-P01), stereo receiver (SX-P01,
SX-P01DAB), and CD player (PD-P01).
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
REPEAT
SHUFFLE
PLAY MODE
FOLDER
CLEAR
DISPLAY
iPod CONTROL
TOP
MENU
1 2 3 PGM
4 5 6
7 8 9
0
10 100
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
ENTER
Favorite
P
R
E
S
E
T
SORT
3
1
8
10
11
12
9
7
6
13
4
5
2
Page: 6
7
Buttons available for the network audio player
control mode
The following functions are available only when the remote
control is in the network control mode.
Important
• Press the CONTROL NET button before pressing the
following buttons.
1 Input function buttons
Use to select the input source to this player.
2 TOP MENU
Displays the top menu of each input source.
3 ///
Use to select/switch system settings and modes, and to
confirm actions.
4 ENTER
Press to confirm actions.
5 SETUP
Press to access the player setup menu (page 21).
6 Playback control buttons
The main buttons (, , etc.) are used to control each
function after you have selected it using the input function
buttons.
7 Numeric buttons
Use to enter the number.
8 CLEAR
Use to select/switch system settings.
9 DIMMER
Make the display brighter, darker, or turn it off altogether. The
brightness can be controlled in four steps (page 14).
10 iPod CONTROL
Switches between the iPod controls and the player controls
(page 16).
11 RETURN
Exit the current menu screen.
12 Playback mode buttons
REPEAT – Press to change repeat play setting from a
iPod, USB, Internet Radio, Music Server or Favorites.
SHUFFLE – Press to change shuffle play setting from a
iPod, USB, Internet Radio, Music Server or Favorites.
13 +Favorite
When using the Internet Radio or Music Server functions,
use to add an audio file or a station to Favorites function
(page 27, 29).
14 SORT
When using the Music Server function, allows tracks to be
sorted if the DLNA server supports the sort function.
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
REPEAT
SHUFFLE
PLAY MODE
FOLDER
CLEAR
DISPLAY
iPod CONTROL
TOP
MENU
PGM
100
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
ENTER
Favorite
1 2 3
4 5 6
7 8 9
0
10
P
R
E
S
E
T
SORT
4
4
3
2
1
5
6
9
10
11
12
13
14
8
7
Page: 7
8
Buttons available for the stereo receiver control
mode
The following functions are available only when the remote
control is in the stereo receiver control mode.
Important
• Press the CONTROL RCV button before pressing the
following buttons.
1 BAND
N-P01:Switches between FM ST (stereo) and FM MONO radio
bands (page 47, 48).
XN-P02, XN-P02DAB: Switches between FM ST (stereo) and
FM MONO, and DAB radio bands (page 49).
2 TIMER
Press to set the wake-up timer or check the current setting
(page 46).
3 TOP MENU
Press to display the DAB setting menu (XN-P02DAB only)
(page 50).
4 ///
Use to select system setting and switch modes.
TUNE / – Use to find radio frequencies (page 47, 49).
PRESET / – Use to select preset radio stations
(page 47).
5 ENTER
Press to confirm actions.
6 SETUP
Press to access the setup menu (page 45, 51).
7 AUTO TUNE
Press to start the DAB auto scan (XN-P02DAB only)
(page 49).
8 RDS function buttons
PTY – Use to search for RDS program types (page 48).
RDS DISP – Press to display the different types of RDS
information available (page 48).
9 Numeric buttons
Use to enter the number.
10 CLOCK
Press to set the clock (page 44).
11 DIMMER
Press to adjust the brightness of the display (page 44).
12 DISPLAY
Press to display information of the current mode (page 48,
49).
13 RETURN
Press to exit the current menu screen.
14 TUNER EDIT
Use to memorize/name stations for recall (page 47).
15 CLEAR
Press to clear the specified settings.
Note
• Stereo receiver control mode can only be used by
customers using the stereo receiver (SX-P01, SX-P01DAB).
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
REPEAT
SHUFFLE
PLAY MODE
FOLDER
CLEAR
DISPLAY
iPod CONTROL
TOP
MENU
PGM
100
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
ENTER
Favorite
1 2 3
4 5 6
7 8 9
0
10
P
R
E
S
E
T
SORT
6
5
8
4
3
2
1
6
7
10
11
12
13
14
15
9
Page: 8
9
Buttons available for the CD player control mode
The following functions are available only when the remote
control is in the CD player control mode.
Important
• Press the CONTROL CD button before pressing the
following buttons.
1 TOP MENU
Press to display the iPod/iPhone/iPad mini top menu.
2 ///
Use to select system setting and switch modes.
3 ENTER
Press to confirm actions.
4 SETUP
Press to access the setup menu.
5 Numeric buttons
Use to enter the number.
6 CLEAR
Press to clear a programmed track.
7 DIMMER
Press to adjust the brightness of the display.
8 DISPLAY
Press to display information of the current mode.
9 RETURN
Press to exit the current menu screen.
10 Playback control buttons
Use buttons to control playback.
11 PGM
Press to set programmed playback.
12 Playback mode buttons
REPEAT – Press to repeat the playback of track/file.
SHUFFLE – Press to shuffle the playback order of tracks/
files.
13 PLAY MODE
Press to enter the folder playback mode.
14 FOLDER +/–
Use to select a folder of a MP3/WMA disc or of a USB mass
storage device.
Note
• CD player control mode can only be used by customers
using the CD player (PD-P01).
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
REPEAT
SHUFFLE
PLAY MODE
FOLDER
CLEAR
DISPLAY
iPod CONTROL
TOP
MENU
PGM
100
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
ENTER
Favorite
1 2 3
4 5 6
7 8 9
0
10
P
R
E
S
E
T
SORT
3
3
6
2
1
4
7
11
13
12
14
8
10
9
5
Page: 9
10
1
1 Controls and displays (Network audio player: N-P01)
Front panel
1 STANDBY/ON button
Switches the player between standby and on (page 14).
2 USB terminal
Use to connect your USB mass storage device or iPod/
iPhone/iPad as an audio source (page 12, 20).
3 Display
See Display below.
4 Remote sensor
Receives the signals from the remote control (page 5).
5 SOURCE
Select the input source (page 14).
6 Playback control button
Select the desired track or folder to be played back. Use  to
stop the playback. Use / to stop playback or resume
playback from the pause point.
Display
1 Input source
2 Network connection status
When the player is connected to the wired network,
this indicator lights (page 12).
When the player that is connected to the LAN cable is
not connected to the network, this indicator lights. When
the LAN cable is not connected to this player, this
indicator does not light (page 12).
When the player is connected to the wireless network,
this indicator lights. Depending on the strength of
wireless signal, the icon changes in five steps (page 12).
When the player is not connected to the wireless
network, this indicator lights (page 12).
Displayed when the wireless network settings for the
player are still set to their initial settings. See (page 21) for
details on performing wireless settings.
3 Name of file/track/artist/album/station, etc.
4 Artwork
Displayed when the currently playing file includes an album
jacket image, etc.
5 Repeat and Shuffle
Repeat all files.
Repeat a file.
Shuffle
6 Play status
Displays the play status. The play status differs depending on
the input source.
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
2
1 3 4 6
5
iPod/USB
Song 1
Artist
Album
44:38 - 44:02
7
7
1 2
3
6
4
5
1
Page: 10
2
2
11
Connecting your equipment (Network audio player: N-P01)
CAUTION
• Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
• Connect the power cord after all the connections between
devices have been completed.
WLAN antenna connection
Connect the WLAN antenna to the WLAN ANTENNA
terminal.
Please always use the supplied WLAN antenna.
Analog audio output connections
By connecting this unit’s analog audio output to the analog
audio input of an amplifier, you can use the amplifier to enjoy
analog audio produced from this unit.
Note
• If you are using the XN-P02 or XN-P02DAB, please refer to
the connection method shown on page 43.
• If you are using in combination with the XC-P01 or XC-
P01DAB, please refer to the connection method shown on
page 13.
Digital audio output connections
By connecting this unit’s digital audio output to the digital
audio input of an AV receiver or D/A converter, etc, you can
use the amplifier to enjoy digital audio produced from this
unit.
Note
• Digital signal formats that can be output from this unit
include linear PCM signals with sampling rate and
quantitative bits up to 192 kHz/24 bits (depending on the
connected device and environment, operation may not be
successful).
• Digital audio signals that can be output from this unit’s
DIGITAL OUT connectors include the following inputs:
iPod/USB (*1), Internet Radio, Spotify and Music Server
(*1).
*1: Not including DSD file playback
• When you select BT audio, USB or Music Server and
playback a DSD file, no signal will be output from the unit’s
DIGITAL OUT (OPTICAL) connector. Please use the AUDIO
OUT connector.
L
R
DIGITAL
OUT
CONTROL
OPTICAL
WLAN ANTENNA
AC IN
WLAN ANTENNA
LAN (10/100)
AUDIO
OUT
OUT
WLAN ANTENNA
AC IN
WLAN ANTENNA
AC IN
WLAN ANTENNA
WLAN ANTENNA
1
2
3 1
2
3
Supplied WLAN
antenna
Supplied WLAN
antenna
Power cord
To AC outlet
L
R
DIGITAL
OUT
CONTROL
OPTICAL
WLAN ANTENNA
LAN (10/100)
AUDIO
OUT
OUT
ANALOG
R L
AUDIO INPUT
Amplifier
L
R
DIGITAL
OUT
CONTROL
OPTICAL
WLAN ANTENNA
LAN (10/100)
AUDIO
OUT
OUT
DIGITAL IN
OPTICAL
AV receiver, D/A
converter, etc.
Page: 11
12
2
2 Connecting your equipment (Network audio player: N-P01)
Connecting USB storage devices
It is possible to listen to two-channel audio using the USB
terminal on the front of this player.
1 Connect your USB device to the USB terminal on the
front panel of this player.
• This player does not support a USB hub.
Connecting to the network through the LAN
interface or WLAN antenna
By connecting this player to the network via the LAN interface
or WLAN antenna, you can play back audio files stored on
components on the network, including your PC, and listen to
Internet radio stations.
Connect the LAN terminal on this player to the LAN terminal
on your router (with or without the built-in DHCP server
function) with a straight LAN cable (CAT 5 or higher). Also
wireless connection to the network is possible.
Requires network settings to be performed. For details, See
Playback with NETWORK features (Network audio player: N-
P01) on page 21
Note
• If you are not using network functions then it is
recommended that you set Network Type to Wired under
Network Setting.
• To use services such as Internet radio, you must conclude
a contract with an Internet service provider.
• Photo or video files cannot be played back.
• With Windows Media Player 12, you can even play back
copyrighted audio files on this player.
Connecting using LAN cable
Connecting using wireless LAN
Using centralized control with other Pioneer
components
Multiple Pioneer components equipped with CONTROL IN/
OUT jacks can be connected to the unit, allowing centralized
control of the components via the remote sensor on the unit.
This also allows remote control of components not equipped
with a remote sensor, or installed in places where the
component’s remote sensor cannot be accessed.
Note
• If you are using the XN-P02 or XN-P02DAB, please refer to
the connection method shown on page 43.
• If you are using in combination with the XC-P01 or XC-
P01DAB, please refer to the connection method shown on
page 13.
Note
• For connections use a supplied monaural miniplug cord
(without resistor).
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
USB storage device
(commercially available)
LAN (10/100)
WAN
3 2 1
LAN
Internet
Router
Computer
This player’s rear
panel
LAN cable
(commercially
available)
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
WAN
3 2 1
LAN
Internet
WirelessLAN
router
Computer
Modem
IN
OUT
CONTROL
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
CONTROL
OUT
Other Pioneer component
equipped with CONTROL
IN/OUT jacks
To other Pioneer component
equipped with CONTROL IN
jack
N-P01
Aim remote control at
the sensor on the unit.
Remote
control
Modem
Page: 12
13
2
2 Connecting your equipment (Network audio player: N-P01)
• When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be used to
make analog connections. Merely connecting the
CONTROL IN/OUT jacks alone will not allow proper system
control.
Using combined with the XC-P01 or
XC-P01DAB
• Connect the stereo receiver (SX-P01, SX-P01DAB) and
network audio player (N-P01) using the supplied remote
control cable and RCA audio cable.
Note
• When the stereo receiver (SX-P01, SX-P01DAB) and
network audio player (N-P01) are connected using the
remote control cable, the stereo receiver remote control
signal receiver will not function. Point the remote control at
the remote control signal receiver on the network audio
player.
• When connecting to the control connector, you must also
connect the audio cable (analog connection). Only
connecting to the control connector will not allow for
correct system control.
• Connecting the remote control cable will allow the Pioneer
ControlApp to be used, providing simple control over the
stereo receiver (SX-P01, SX-P01DAB) via the network audio
player (N-P01). Refer to page 31 for details of the Pioneer
ControlApp.
• If the network audio player’s quick start setting is Off then
you will be unable to control the stereo receiver or CD
player.
Turn the network audio player’s quick start setting On and
you will be able to control them.
Plugging in
Before making or changing the connections, switch off the
power and disconnect the power cord from the AC outlet.
After you’ve finished making all connections, plug the player
into an AC outlet.
L
R
DIGITAL
OUT
CONTROL
OPTICAL
WLAN ANTENNA
LAN (10/100)
AUDIO
OUT
OUT
N-P01
SX-P01 or SX-P01DAB
CD Player (PD-P01)
WLAN ANTENNA
AC IN
To AC outlet
This player’s rear
panel
Power cord
Page: 13
3
3
14
Getting started (Network audio player: N-P01)
Setting the player
When you use the player for the first time, the following
screens will be displayed.
Set up the following items to customize the player.
1 Press  NETWORK.
The power indicator flashes slowly. About twenty seconds
after turning on the power, the following screen appears.
About thirty seconds are required between turning the
power on and completion of startup.
When powering up for the first time
When you turn on the power to the player for the first time,
initial settings will be automatically performed, thus startup
will take about 1 minute.
• After the Pioneer logo is displayed, the screen will go dark.
The start up process is complete once the Pioneer logo is
displayed a second time.
Auto Power Off setup
Set to automatically turn off the player after a specified time
has passed (when the power has been on with no operation
for the set period of time).
• Default setting: 15 min
1 Press NET SERVICE, then press SETUP on the remote
control.
The Initial Setup menu is shown on the display.
2 Select ‘Option Setting’ from Initial Setup menu.
3 Select ‘Power Off Setting’ from Option Setting menu.
4 Select ‘Auto Power Off’ from Power Off Setting menu.
5 Use / to specify the amount of time to allow before
the power is turned off (when there has been no
operation), then press ENTER.
Select 15 minutes (default setting) or 30 minutes, 60
minutes or OFF.
6 When you’re finished, press RETURN.
General control
Input function
When pressing SOURCE button on the player, the current
function will change to different mode. Press SOURCE button
repeatedly to select desired function. The selected input is
displayed on the front panel display.
Note
• The backup function will protect the memorised function
mode should there be a power failure or the AC power cord
becomes disconnected.
Display brightness control
Press the CONTROL NET button on the remote control. Press
DIMMER button to dims the display brightness. The
brightness can be controlled in four steps.
BT Audio
iPod/USB Music
Server
Internet
Radio
Favorites Spotify
Page: 14
4
4
15
iPod/iPhone/iPad playback (Network audio player: N-P01)
Merely by connecting your iPod/iPhone/iPad to this player,
you can enjoy high-quality sound from your iPod/iPhone/iPad.
Confirming what iPod/iPhone/iPad models are
supported
The iPod/iPhone/iPad playable on this player are shown
below.
Note
• USB works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s,
iPhone 4, iPhone 3GS, iPad Air, iPad (3rd and 4th
generation), iPad 2, iPad mini with Retina Display, iPad
mini, iPod touch (1st through 5th generation) and iPod
nano (3rd through 7th generation). However, some of the
functions may be restricted for some models. The player is
not compatible with the iPod shuffle.
• This player has been developed and tested for the software
version of iPod/iPhone/iPad indicated on the website of
Pioneer (http://pioneer.jp/homeav/support/ios/eu/).
• Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone/iPad may result in
incompatibility with this player.
• iPod, iPhone and iPad are licensed for reproduction of
noncopyrighted materials or materials the user is legally
permitted to reproduce.
• Features such as the equalizer of iPod/iPhone/iPad cannot
be controlled using this player, and we recommend
switching the equalizer off before connecting.
1 Select “Settings” from the top menu.
You can confirm your software version by operating your
iPod/iPhone/iPad. When using iPod touch, iPhone or
iPad, select “General” after selecting “Settings”.
2 Select “About”.
The software version will be displayed.
Connect iPod/iPhone/iPad to the USB terminal
Connect your iPod/iPhone/iPad to the USB terminal on the
player’s front panel. Use the iPod cable supplied with your
iPod/iPhone/iPad for the connection.
• For the cable connection, also refer to the operating
instructions for your iPod/iPhone/iPad.
iPod/iPhone/iPad Audio Control
iPod nano 3G/4G/5G/6G/7G  
iPod touch 1G/2G/3G/4G/5G  
iPhone 3GS  
iPhone 4  
iPhone 4s  
iPhone 5  
iPhone 5c  
iPhone 5s  
iPad mini  
iPad mini with Retina Display  
iPad 2  
iPad (3rd generation)  
iPad (4th generation)  
iPad Air  
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
Page: 15
4
4
16
iPod/iPhone/iPad playback (Network audio player: N-P01)
Playing your iPod/iPhone/iPad
CAUTION
• When your iPod/iPhone/iPad is connected to this player
and you wish to operate the iPod/iPhone/iPad directly, be
sure to hold the iPod/iPhone/iPad steady with the other
hand to prevent malfunctions due to faulty contacts.
1 Connect your iPod/iPhone/iPad.
To connect your iPod/iPhone/iPad, see Connect iPod/
iPhone/iPad to the USB terminal on page 15.
2 Press iPod/USB to select iPod/USB as the input source.
iPod/USB is shown on the display and starts playback.
Note
• When the iPod/iPhone/iPad is connected to this player, the
playback information for the songs are displayed on the
iPod/iPhone/iPad display. Pressing iPod CONTROL
button on the remote will switch the display and display the
information on the front panel of the player.
Important
• If this player cannot play your iPod/iPhone/iPad, perform
the following troubleshooting checks:
- Check whether the iPod/iPhone/iPad is supported by this
player (page 15).
- Reconnect the iPod/iPhone/iPad to the player. If this
doesn’t seem to work, try resetting your iPod/iPhone/
iPad.
- Check the iPod/iPhone/iPad software is supported by this
player.
• If the iPod/iPhone/iPad cannot be operated, check the
following items:
- Is the iPod/iPhone/iPad connected correctly? Reconnect
the iPod/iPhone/iPad to the player.
- Is the iPod/iPhone/iPad experiencing a hangup? Try
resetting the iPod/iPhone/iPad, and reconnect it to the
player.
- When connecting the iPad, use only an iPad dedicated
cable.
Tip
• iPod/iPhone/iPad recharging occurs whenever an iPod/
iPhone/iPad is connected to this player. (This function is
only supported when the power is initially turned on or
during Network Standby).
• When input is switched from iPod/USB to another
function, iPod/iPhone/iPad playback is temporarily
stopped.
Page: 16
5
5
17
Music playback using Bluetooth® wireless technology (Network audio player: N-P01)
The unit is capable of playing back music stored on Bluetooth
capable devices (cell phones, digital music players etc.)
wirelessly. You can also use a Bluetooth audio transmitter
(sold separately) to enjoy music from devices that do not have
Bluetooth functionality. Please refer to the user’s manual for
your Bluetooth capable device for more details.
Note
• The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by PIONEER CORPORATION is under license.
Other trademarks and trade names are those of their
respective owners.
• The Bluetooth wireless technology enabled device must
support A2DP profiles.
• Pioneer does not guarantee proper connection and
operation of this unit with all Bluetooth wireless technology
enabled devices.
Remote control operation
The remote control supplied with this unit allows you to play
and stop media, and perform other operations.
Note
• The Bluetooth wireless technology enabled device must
support AVRCP profiles.
• Remote control operations cannot be guaranteed for all
Bluetooth wireless technology enabled devices.
Pairing with the unit (Initial registration)
In order for the unit to playback music stored on a Bluetooth
capable device, pairing must first be performed. Pairing
should be performed when first using the unit with the
Bluetooth capable device, or when the pairing data on the
device has been erased for any reason.
Pairing is a step required to allow communication using
Bluetooth wireless technology to be carried out.
• Pairing is only performed the first time that you use the unit
and the Bluetooth capable device together.
• In order to allow communication using Bluetooth wireless
technology to take place, pairing must be performed on
both the unit and the Bluetooth capable device.
• After pressing the BT AUDIO and switching to BT Audio
function, perform the pairing procedure on the Bluetooth
capable device. If pairing has been performed correctly,
you will not need to perform the pairing procedures for the
unit as shown below.
Please refer to the user’s manual for your Bluetooth capable
device for more details.
1 Press the STANDBY/ON and turn the power to the unit
on.
2 Press the BT AUDIO.
The unit switches to BT Audio and “Waiting device” will be
displayed.
• Waiting device
3 Turn on the power to the Bluetooth capable device that
you wish to pair with, and perform pairing procedure on
it.
Note
• This unit will be displayed as “N-P01” on all Bluetooth
capable devices that you have.
Pairing will start.
• Place the Bluetooth capable device close to the unit.
• Please refer to the user’s manual for your Bluetooth
capable device for details on when pairing can be
performed and the procedures required for pairing.
• When PIN code entry is requested, enter “0000.” (This unit
does not accept any PIN code setting other than “0000.”)
4 Confirm on the Bluetooth capable device that pairing
has been completed.
If pairing with the Bluetooth capable device has been
completed correctly “Connected“ will be displayed.
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
Remote control operation
Device not equipped with Bluetooth
wireless technology: Digital music
player
+
Bluetooth®
wireless technology audio
transmitter (commercially available)
Bluetooth wireless technology enabled device:
Digital music player
Bluetooth wireless technology enabled device:
Cell phone
BT Audio
Waiting Device
Page: 17
5
5
18
Music playback using Bluetooth® wireless technology (Network audio player: N-P01)
• Connected
Listen to music on the unit from a Bluetooth
capable device
1 Press the BT AUDIO.
The unit will switch to BT Audio input.
2 A Bluetooth connection will be created between the
Bluetooth capable device and the unit.
Procedures for connecting to the unit should be
performed from the Bluetooth capable device.
• Please refer to the user’s manual for your Bluetooth
capable device for details of the connection procedures.
3 Playback music from the Bluetooth capable device.
Note
• When Bluetooth capable device is not connected and no
operations have been performed for the length of time set
under Settings for Auto Power Off, the unit will
automatically power off. Please set it to any setting other
than “OFF” under Settings.
• Auto Power Off can select 15 minutes (default setting) or 30
minutes, 60 minutes or OFF. (page 14).
Bluetooth Standby Mode
1 Press NET SERVICE, then press SETUP on the remote
control.
The Initial Setup screen is shown on the display.
2 Select ‘Option Setting’ from Initial Setup menu.
3 Select ‘Power Off Setting’ from Option Setting menu.
4 Select ‘Bluetooth Standby Mode’ from Power Off
Setting menu.
5 To turn Bluetooth Standby Mode on, Use / to select
ON, then press ENTER.
To turn Bluetooth Standby Mode off, Use / to select
OFF, then press ENTER.
• The following can be done when the unit is on standby with
the Bluetooth Standby Mode switched ON.
Note
• If the power cable has been removed and inserted again,
the function will become effective after the power is turned
ON for the unit.
Connection while in Bluetooth Standby mode with
Bluetooth capable device
When connection history (pairing has already been
conducted) with a Bluetooth capable device exists for the unit
during Bluetooth Standby, the unit can receive a connection
request directly from the connection history.
The unit will start using the BT Audio function, and connect
with a Bluetooth capable device.
Even devices that have already been paired with this unit will
not connect during Bluetooth Standby in the following cases.
In such cases, delete pairing history from the Bluetooth
wireless technology device and perform pairing again.
• Up to 8 pairing history can be recorded with this unit. If
connecting to a Bluetooth wireless technology device over
8 units, the oldest pairing history will be deleted.
• If the settings are reset to the factory setting, all pairing
history will be deleted.
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a band
used by other wireless systems (see list below). To prevent
noise or interrupted communication, do not use this unit
nearby such devices, or make sure these devices are switched
off during use.
• Cordless phones
• Cordless facsimiles
• Microwave ovens
• Wireless LAN devices (IEEE802.11b/g)
• Wireless AV equipment
• Wireless controllers for game systems
• Microwave-based health aids
• Some baby monitors
Other, less common, equipment that may operate on the
same frequency:
• Anti-theft systems
• Amateur radio stations (HAM)
• Warehouse logistic management systems
• Discrimination systems for train or emergency vehicles
Note
• In the event noise appears in your television image, there is
the possibility that a Bluetooth wireless technology enabled
device or this unit (including products supported by this
unit) are causing signal interference with the antenna input
connector of your television, video, satellite tuner, etc. In
this event, increase the distance between the antenna
input connector and the Bluetooth wireless technology
enabled device or this unit (including products supported
by this unit).
• If there is something obstructing the path between this unit
(including devices supported by this unit) and the device
equipped with Bluetooth wireless technology (such as a
metal door, concrete wall, or insulation containing tinfoil),
you may need to change the location of your system to
prevent signal noise and interruptions.
BT Audio
Connected
Page: 18
5
5
19
Music playback using Bluetooth® wireless technology (Network audio player: N-P01)
Scope of operation
Use of this unit is limited to home use. (Transmission
distances may be reduced depending on communication
environment).
In the following locations, poor condition or inability to receive
radio waves may cause the audio to be interrupted or stopped:
• In reinforced concrete buildings or steel framed or iron-
framed buildings.
• Near large metallic furniture.
• In a crowd of people or near a building or obstacle.
• In a location exposed to the magnetic field, static electricity
or radio wave interference from radio communication
equipment using the same frequency band (2.4 GHz) as
this unit, such as a 2.4 GHz wireless LAN device
(IEEE802.11b/g) or microwave oven.
• If you live in a heavily populated residential area
(apartment, townhouse, etc.) and if your neighbor’s
microwave is placed near your system, you may experience
radio wave interference. If this occurs, move your unit to a
different place. When the microwave is not in use, there will
be no radio wave interference.
Radio wave reflections
The radio waves received by this unit include the radio wave
coming directly from the device equipped with Bluetooth
wireless technology (direct wave) and waves coming from
various directions due to reflections by walls, furniture and
building (reflected waves). The reflected waves (due to
obstacles and reflecting objects) further produce a variety of
reflected waves as well as variation in reception condition
depending on locations. If the audio cannot be received
properly due to this phenomenon, try moving the location of
the device equipped with Bluetooth wireless technology a
little. Also note that audio may be interrupted due to the
reflected waves when a person crosses or approaches the
space between this unit and the device equipped with
Bluetooth wireless technology.
Precautions regarding connections to products
supported by this unit
• Complete connections for all devices supported by this
unit, including all audio cords and power cables before
connecting them to this unit.
• After completing connections to this unit, check the audio
and power cables to confirm that they not twisted together.
• When disconnecting this unit, confirm that you have
sufficient working space in the surrounding area.
• When changing connections of audio or other cables for
products supported by this unit, confirm that you have
sufficient working space in the surrounding area.
Page: 19
6
6
20
USB playback (Network audio player: N-P01)
Playing files stored on USB storage devices
This player may not recognize a USB storage device, play files
or supply power to a USB storage device. For details, see
Connecting USB storage devices on page 12.
Pioneer does not guarantee that any file recorded on a USB
storage device will play or that power will be supplied to a USB
storage device. Also note that Pioneer will accept no
responsibility whatsoever for loss of files on USB storage
devices caused by connection to this player.
1 Press iPod/USB to select iPod/USB as the input source.
iPod/USB is shown on the display.
2 Connect the USB storage device.
The folders/files stored on the connected USB storage
device appear on the display automatically.
3 Use / to select the file, then press ENTER.
Playback starts.
• To return to the previous screen, press RETURN.
• When changing to a different input source, stop the
USB memory playback first, before changing.
• Turn the power off before removing the USB storage
device.
Note
• The following screen appears on the display when you play
back audio files. Note that some file types may not be
displayed.
• Display of album names and artist names supports the
following formats.
MP3, WMA, Apple Lossless, FLAC, AIFF(*), DSD.
*In the case of AIFF, files with a sampling frequency of 176
kHz or 192 kHz are not supported.
• Display of album art is supported for MP3 and DSD (DSF
only).
Embedded images are supported for JPEG only.
• The progress bar and the remaining playback time may not
be displayed depending on the play back file.
iPod/USB
Song 1
Artist
Album
1:05
mp3 256 kbps

Page: 20
21
7
7 Playback with NETWORK features (Network audio player: N-P01)
Network setting
If a broadband router (with built-in DHCP server function) is connected to this unit, you can simply turn on the DHCP server function without having to set up the network manually. Before you
set up the network, consult with your ISP or the network manager for the required settings. It is advised that you also refer to the operation manual supplied with your network component. Any
changes made to a router without the DHCP server function must be reflected to unit network settings.
If you select method B, C, D, E or F, confirm the LAN cable is not connected to this unit.
Precautions when connecting this unit to a wireless LAN router
The SSID only supports use of single-byte alphanumeric characters, together with the underbar and certain other symbols. If using another character coding, the SSID must be updated before
making network settings. For more details regarding SSID, consult your router’s operating instructions.
D
F
E
A
C
B
WAN
3 2 1
LAN
Connecting this
unit using wireless
LAN
WAN
3 2 1
LAN
WPS-PBC
Connecting to a router without
WPS-PBC function
Connect this unit directly to your
computer or tablet computer. Settings
must be performed from the Web
browser of the computer or tablet
computer.
WAN
3 2 1
LAN
WPS-PBC
Connecting to a router with WPS-PBC function
If your computer or
tablet computer is
equipped with
wireless LAN
function
If your computer or
tablet computer is
not equipped with
wireless LAN
function (wired LAN
only)
WAN
3 2 1
LAN
Connecting this unit to the router using an iPhone/iPod
touch/iPad (with iOS 7.1 or later)
The same wireless LAN connection settings can be applied to this unit.
Connecting this unit to the router using an iPhone/iPod
touch/iPad (with iOS 5.0 or later)
Connecting this
unit using wired
LAN
C
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
Page: 21
7
7
22
Playback with NETWORK features (Network audio player: N-P01)
A: Wired setting
Make sure that the LAN cable connections has completed
(page 12).
1 Press NET SERVICE  SETUP.
The Initial Setup screen is shown on the display.
2 Select Network Setting  Network Configuration.
3 Use / to select Wired, then press ENTER.
4 Use / to select DHCP On, then press ENTER.
Select Don’t Use Proxy Server.
Note
• If your router does not have a built-in DHCP server function,
you have to set up the network manually.
 Select DHCP to be Off and press ENTER in step 4.
<Manual setting>
Then use /// or numeric buttons to adjust the
numbers, then press ENTER.
/: Moves the adjusting digit.
/: Increases or decreases values.
IP Address
The IP address to be entered must be defined within the
following ranges. If the IP address defined is beyond the
following ranges, you cannot play back audio files stored
on components on the network or listen to Internet radio
stations.
Class A: 10.0.0.1 to 10.255.255.254 / Class B: 172.16.0.1 to
172.31.255.254 / Class C: 192.168.0.1 to 192.168.255.254
Subnet Mask
If an xDSL modem or a terminal adapter is directly
connected to this player, enter the subnet mask listed in
your ISP documentation. In most of the cases, enter
255.255.255.0.
Default Gateway
If a gateway (router) is connected to this player, enter the
corresponding IP address.
Primary DNS Server/Secondary DNS Server
If there is only one DNS server address listed in your ISP
documentation, enter Primary DNS Server. In case there
are more than two DNS server addresses, enter
Secondary DNS Server in the other DNS server address
field.
• When you connect this player to the Internet via a proxy
server, proxy server settings are required.
Select Use Proxy Server and press ENTER in step 4.
<Proxy Server setting>
Then Enter Proxy Host Name and the port number of
your proxy server in the Proxy Port field.
B: Connection settings using an iOS device
(with iOS 5.0 or later)
You can apply iPod/iPhone/iPad (iOS device with iOS ver 5.0
or later)’s Wi-Fi settings to this player.
Note
• The iOS device and router must be connected at 2.4 GHz.
1 Be sure the LAN cable is not connected to the player.
2 Unlock your iPod/iPhone/iPad. Check that the Wi-Fi
mark is displayed on the iOS device.
3 Plug the power cord into an AC outlet. Press STANDBY/
ON.
4 Press iPod/USB on the remote control.
Connect the iOS device to the USB terminal.
5 Press SETUP.
6 Select Network Setting  Network Configuration 
Wireless  iOS Device and then press ENTER.
7 Tap Allow on iPod/iPhone/iPad.
The Wi-Fi settings of your iPod/iPhone/iPad are applied to
the player.
Wireless
Wired
Network Configuration
DHCP Off
DHCP On
Network Configuration


IP Address
XXX . XXX XXX XXX
. .
Share Wi-Fi Settings?
Ignore
Page: 22
23
Playback with NETWORK features (Network audio player: N-P01)
7
7
C: Connection settings using an iOS device
(with iOS 7.1 or later)
You can apply iPod/iPhone/iPad (iOS device with iOS ver 7.1
or later)’s Wi-Fi settings to this player.
Note
• The iOS device and router must be connected at 2.4 GHz.
1 Be sure the LAN cable is not connected to the player.
2 Unlock your iPod/iPhone/iPad that Wi-Fi connection is
completed.
3 Plug the power cord into an AC outlet. Press STANDBY/
ON.
4 Press iPod/USB on the remote control.
5 Press SETUP.
6 Select Network Setting  Network Configuration 
Wireless  Wireless Accessory Configuration and then
press ENTER.
7 Press the iPod/USB button.
Confirm that the Wi-Fi operation mark is displayed.
8 Check that the Wi-Fi mark is displayed on the iPhone,
iPod touch or iPad screen.
If it is not displayed, turn Wi-Fi on, and then connect the
iPhone, iPod touch or iPad to the wireless LAN router.
9 Perform operations on the iPhone, iPod touch or iPad
screen.
• Select Settings.
• Select Wi-Fi.
• Under SET UP NEW AIRPLAY SPEAKER, select this player.
Note
• “*****” is the lower three bytes of the MAC address.
iPod/USB
N-P01 *****
Page: 23
7
7
24
Playback with NETWORK features (Network audio player: N-P01)
• Select Next.
• Wait for the process to be completed.
• Select Done.
10Wait until the Wi-Fi operation mark changes to .
Note
• If your iPhone, iPod touch, iPad and the router are
connected at 5 GHz then you will be unable to use this
setting method. Please try a different setting method.
• Images of the screen are taken from iOS7.1. If your iPod/
iPhone/iPad has software other than iOS7.1 installed,
control of the iPod/iPhone/iPad may differ.
D: WPS connection setting
WPS is abbreviation of Wi-Fi Protected Setup. A standard
established by the Wi-Fi Alliance industry group for a function
allowing settings related to interconnection of WPS
compatible wireless LAN devices and encryption to be made
with simple operations.
This player supports push-button configuration and PIN code
configuration.
Network Type must be set to Wireless or Auto to use WPS
connection. When using WPS connection, be sure the LAN
cable is not connected to the player and turn this player on.
1 Press NET SERVICE  SETUP on the remote control.
The Initial Setup screen is shown on the display.
2 Select Network Setting  WPS.
3 Use / to select PBC (Push Button Configuration) or
PIN Input, then press ENTER.
If your wireless device supports PBC, select PBC.
PBC (Push Button Configuration)
Connection settings are made automatically simply by
pressing the WPS buttons on the WPS compatible
wireless LAN device. Follow the instructions on the
display. This is the simplest way of making the settings,
and is possible when the WPS compatible wireless LAN
device is equipped with WPS button.
PIN INPUT
Connection settings are made by inputting the 8-digit PIN
code shown on the display to the access point to which
you selected.
N-P01 *****
iPod/USB
PIN Input
PBC (Push Button Configuration)
Select WPS Method
Page: 24
25
Playback with NETWORK features (Network audio player: N-P01)
7
7
Follow the instructions shown in Connecting using PIN
code configuration on the right.
Connecting using PIN Input
1 Press NET SERVICE  SETUP. Select Network Setting 
WPS  PIN Input, then press ENTER.
2 Use / to select the access point which you want to
connect, then press ENTER.
3 Confirm the PIN code of this player, then press ENTER.
The PIN code of this player is shown on the display.
You must check this PIN code to connect to the network.
4 Within 2 minutes after closing the PIN Code message,
input the PIN Code to the access point selected in step 2.
The connection success or failure is displayed on the
display. The PIN Code input method differs depending on
the LAN device used. For details, consult the operating
instructions accompanying your LAN device.
E: Wireless Setting
1 Press NET SERVICE  SETUP.
The Initial Setup screen is shown on the display.
2 Select Network Setting  Network Configuration.
3 Use / to select Wireless, then press ENTER.
4 Use / to select Auto, then press ENTER.
If you setup manually, select Manual.
5 Use / to select the available wireless network you
want to connect to.
6 Use /// to enter the Pass Phrase or WEP Key.
/: Moves the adjusting digit.
/: Changes displayed character.
REPEAT: Switches character types.
CLEAR: Deletes one character at a time.
7 Use / to select DHCP On, then press ENTER.
Select Don’t Use Proxy Server.
002XXXXXX
001XXXXXX
Available Wireless Networks
003XXXXXX
[ENTER]
88192420
Start
Wireless
Wired
Network Configuration
Manual
Wireless Accessory Configuration
Web Control
Auto
Wireless
002XXXXXX
001XXXXXX
Available Wireless Networks
003XXXXXX


Enter Password
[REPEAT] Change Text
Delete One Character
[CLEAR]
A
DHCP Off
DHCP On
Network Configuration
Page: 25
7
7
26
Playback with NETWORK features (Network audio player: N-P01)
Note
• If your router does not have a built-in DHCP server function,
you have to set up the network manually.
Select DHCP to be Off and press ENTER in step 7. If your
router does not have a built-in DHCP server function, you
have to set up the network manually.  Select DHCP to be
Off and press ENTER in step 4. on page 22
• When you connect this player to the Internet via a proxy
server, proxy server settings are required.
Select Use Proxy Server and press ENTER in step 7.
<Proxy Server setting>
Then Enter Proxy Host Name and the port number of
your proxy server in the Proxy Port field.
F: Connecting to a router without WPS-PBC
function
This section describes how to set the network connection
using Web browser on a computer.
Be sure your computer is equipped with wireless LAN
function. Settings can be performed from the Web browser of
the computer.
1 Be sure the LAN cable is not connected to the player.
2 Plug the power cord into an AC outlet. Press STANDBY/
ON.
3 Press NET SERVICE  SETUP on the remote control.
4 Select Network Setting  Network Configuration 
Wireless  Web Control.
5 Select Start  OK.
The player restarts. Change settings on Web Control on
your computer.
6 Select Pioneer Setup (this player) in the available
wireless network connection of your computer.
SSID is displayed as Pioneer Setup:xxxxxx. “xxxxxx” is the
lower three bytes of the MAC address.
Note
• Consult the appropriate operating instructions for
information regarding operation of the computer, iPhone,
tablet computer or other device used.
• Since this kind of connection is not encoded, a minor
security risk may be involved.
• This setting for the network has been confirmed for Mac OS
X 10.7 and Safari 5.1.
7 Start your computer's Web browser, and access the URL
noted below to make settings for this unit.
The Web Control menu will appear.
For Safari
Press Bookmark icon ( ) at the upper left of the
screen. Click Bonjour list (a), and then select this unit’s
name (“Friendly Name”) (b) in Bookmark.
Note
• The displayed name will change depending on the product
being used.
N-P01 *****, XN-P02 ***** or XN-P02DAB ***** will be
displayed. (“*****” is the lower three bytes of the MAC
address.)
8 Click Network Setup  Network Configuration. Select
Auto and then press OK.
9 Setup the network settings manually and then press
Apply.
If SSID is not displayed, return to step 9 and select
Manual.
The player restarts and the new network settings are applied
to the player.
Note
• You can set the network as in the above by connecting this
unit’s IP address via the Web Browser even if Web Control
isn’t selected.
000001
000002
000003
XX.XX
:xxxxxx
http://192.168.1.1
192.168.1.1
a
b
N-P01 *****
N-P01 *****
Page: 26
27
Playback with NETWORK features (Network audio player: N-P01)
7
7
Friendly Name
1 Press NET SERVICE  SETUP.
2 Select Network Setting  Friendly Name.
3 Use /// to enter Friendly Name, then press
ENTER.
/: Moves the adjusting digit.
/: Changes displayed character.
REPEAT: Switches character types.
CLEAR: Deletes one characters at a time.
Listening to the Internet radio
You can select and listen to your favorite Internet radio station
from the list of Internet radio stations created, edited, and
managed by the vTuner database service exclusively for use
with the Pioneer products.
Connecting to a LAN network
Connect to the network using the LAN interface or WLAN
antenna.
For details on the connections, see Connecting to the network
through the LAN interface or WLAN antenna on page 12.
Listening to the Internet radio for the first time
When you listen to the Internet radio first time, follow the
instructions below to tune into your desired station.
1 Press NET SERVICE repeatedly to select Internet Radio as
the input source.
Internet Radio is shown on the display.
2 Use / to select the folder and press ENTER.
Favorite folder is displayed when you have added the stations
via vTuner.
Tune into a station
1 Press NET SERVICE repeatedly to select Internet Radio as
the input source.
The information of the station you last selected is
displayed on the display.
2 Press TOP MENU to display Internet Radio menu screen.
3 Use / to select the folder and press ENTER.
You can select Favorites function when you have already
added your favorite station to Favorites.
To add stations, press +Favorite on the remote control.
4 Use / to select the station, then press ENTER.
You can also select the available stations from the
internet radio menu.
Playing back your favorite songs
Up to 64 favorite tracks on the media server and/or Internet
Radio stations can be registered in Favorites function. Note
that only the audio files stored on components on the network
can be registered.
Registering and deleting audio files and Internet
radio stations in and from Favorites
1 Press NET SERVICE on the remote control to select
Internet Radio.
2 Select the track or Internet radio station you want to
register, press +Favorite on the remote control.
The selected song or Internet Radio station is registered
in Favorites.
Note
• To delete a registered song, select Favorites, select the
song you want to delete from Favorites, and press CLEAR.
The selected song is then deleted from Favorites.
Advanced operations for the Internet radio
Registering broadcast stations not on the vTuner
list from the special Pioneer site
With this player, broadcast stations not included on the list of
stations distributed by vTuner can be registered and played.
Check the access code required for registration on this player,
use this access code to access the special Pioneer Internet
radio site and register the desired broadcast stations in your
favorites. The address of the special Pioneer Internet radio site
is: http://www.radio-pioneer.com
Genres
Podcasts By Genre
Podcasts By Location
Countries
Internet Radio


Top Menu
Page: 27
7
7
28
Playback with NETWORK features (Network audio player: N-P01)
1 Display Internet Radio screen.
To display the Internet radio list screen, perform steps 1 to
2 at Listening to the Internet radio for the first time above.
2 Use / to select Help, then press ENTER.
3 Use /to select Get access code, then press ENTER.
The access code required for registration on the special
Pioneer Internet radio site is displayed. Make a memo of
this address.
The following can be checked on the Help screen:
• Get access code – The access code required for
registration on the special Pioneer Internet radio site is
displayed.
• Show Your WebID/PW – After registering on the
special Pioneer Internet radio site, the registered ID and
password are displayed.
• Reset Your WebID/PW – Resets all the information
registered on the special Pioneer Internet radio site.
When reset, all the registered broadcast stations are
also cleared. If you want to listen to the same stations,
re-register after resetting.
4 Access the special Pioneer Internet radio site from your
computer and perform the registration process.
Access the above site and use the access code in step 3
to perform user registration, following the instructions on
the screen.
5 Register the desired broadcast stations as your
favorites, following the instructions on the computer’s
screen.
Both broadcast stations not on the vTuner list and
stations on the vTuner list can be registered. In this case
they are registered on the player as favorite broadcast
stations and can be played.
Note
• Playback may stall when the computer is switched off or
any media files stored on it are deleted while playing
content.
• If there are problems within the network environment
(heavy network traffic, etc.) content may not be displayed or
played properly (playback may be interrupted or stalled).
For best performance, a 100BASE-TX connection between
player and computer is recommended.
About the Spotify audio stream playback
function
Spotify is a music streaming distribution service managed
and operated by Spotify Ltd. and distributing music over the
Internet.
Spotify audio streams can be enjoyed using this unit and your
smartphone or other mobile digital device.
Preparations (1) Installing the Spotify application
on mobile digital devices and registering a
Spotify Premium account
Important
• The Spotify application must be installed on mobile digital
devices and you must have registered a Spotify Premium
account (for a charge) in order to use the Spotify audio stream
playback function on this unit.
For registration procedures, see the Spotify website.
http://www.spotify.com/
http://www.spotify.com/connect
For information on the countries and regions where Spotify
services can be used, see the website below.
http://www.spotify.com/
Spotify functions may be changed without notice. An Internet
connection is required on the mobile digital device in order to
use the Spotify application. Using the mobile telephone line
for the Internet connection tends to lead to high packet
communication charges, so we recommend subscribing to a
fixed packet rate plan. For details, contact your mobile
telephone operator.
Preparations (2) Connecting this unit to the
network
• Connect this unit to the network and also to the Internet.
For instructions on connecting, see this unit’s operating
instructions.
• Connect the mobile digital device by Wi-Fi to the wireless
LAN router of the same network as the one to which this
unit is connected. For instructions on connecting, see the
operating instructions of the mobile digital device and the
wireless LAN router.
In order to use the Spotify audio stream playback
function from the Spotify application
To use the Spotify audio stream playback function, select this
unit on the Spotify application.
When Spotify audio streaming starts, this unit’s input
automatically switches to Spotify.
CAUTION
• Even if you are away from home, if you start Spotify audio
streaming to play music on your mobile digital device and
this unit is selected, the sound will be output from this unit.
Depending on the volume level, the output may be loud, so
be sure to check the audio output selection carefully before
starting audio streaming. In addition, if you accidentally
select this unit and play the sound on it, switch the audio
output selection to the mobile digital device.
Note
• A separate contract with/payment to an Internet service
provider is required to use the Spotify audio stream
playback function.
• This unit’s name is displayed as the playback device on the
Spotify application. Also, this unit’s name can be changed
at “Friendly Name” in the network settings.
• When this unit is selected with the Spotify application, the
account information is registered on this unit as well.
When disposing of this unit, reset this unit’s settings in
order to delete the account information registered on this
unit. For instructions on resetting, See Resetting this player
on page 36.
Use the player to listen to Spotify audio stream
1 Press NET SERVICE repeatedly to select Spotify as the
input source.
Spotify is shown on the display.
Playback will begin automatically. If playback does not
begin, press .
Note
• In order to use the player to listen to Spotify audio stream,
you must register the account information to the player. In
order to register the account information, use the Spotify
Application and select the player.
Page: 28
29
Playback with NETWORK features (Network audio player: N-P01)
7
7
This player can play audio files stored on computers or other
components on a Local Area Network (LAN).
Introduction
This player allows you to listen to audio files on a computer or
other component connected to the player via LAN interface.
This chapter describes the setup and playback procedures
required to enjoy these features. It is advisory that you also
refer to the operation manual supplied with your network
component.
Note
• Photo or video files cannot be played back.
• With Windows Media Player 11 or Windows Media Player
12.
About playable DLNA network devices
This player allows you to play music on media servers
connected on an identical Local Area Network (LAN) as the
player. This player allows you to play files stored on the
following devices:
• Computers running Microsoft Windows Vista with
Windows Media Player 11 installed
• Computers running Microsoft Windows 7 or 8 with
Windows Media Player 12 installed
• DLNA-compatible digital media servers (on computers or
other components)
Files stored in a computer or DMS (Digital Media Server) as
described above can be played via command from an external
Digital Media Controller (DMC). Devices controlled by this
DMC to play files are called DMRs (Digital Media Renderers).
This player supports this DMR function.
When this player is selected as a DMR and DMS playback is
begun, the player’s input automatically switches to DMR.
During DMR input, the currently playing track name, artist
name, album name, and album art will appear on the player’s
display (some information may not be displayed, depending
on the file being played).
When in the DMR mode, such operations as playing and
stopping files can be performed from the external controller.
Volume adjustment and the muting control are also possible.
Note
• Depending on the external controller being used, playback
may be interrupted when the volume is adjusted from the
controller. In this case, adjust the volume from the player or
remote control.
Using AirPlay on iPod touch, iPhone, iPad and
iTunes
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion or later, and PC
with iTunes 10.2.2 or later.
To use AirPlay, select your player on your iPod touch, iPhone,
iPad or in iTunes and start playback. For more information,
see the Apple website (http://www.apple.com).
• Adjustment of the player’s volume from iPod touch,
iPhone, iPad or iTunes.
• Pause/resume, next/previous track, and shuffle/repeat
from the remote control of the player. The display will not
show the Play Status, Repeat, or Shuffle icons.
• Display of the currently playing track information on the
player’s display, including artist, song/album name and
album artwork. It may not be displayed other than song
name.
Tip
• A network environment is required to use AirPlay.
• The player’s name that shows up in the AirPlay UI on iPod
touch, iPhone, iPad and iTunes can be changed by
Friendly Name from Network Setting.
• AirPlay provided on this player has been developed and
tested based on the software versions for the iPod touch,
iPhone, iPad and the software versions for iTunes that are
indicated on the Pioneer website. AirPlay may not be
compatible with iPod touch, iPhone, iPad or iTunes
software versions other than those indicated on the Pioneer
website.
About the DHCP server function
To play back audio files stored on components on the network,
you must turn on the DHCP server function of your router.
In case your router does not have the built-in DHCP server
function, it is necessary to set up the network manually.
Otherwise, you cannot play back audio files stored on
components on the network or listen to Internet radio
stations. See Network setting on page 21 for more on this.
Authorizing this player
This player must be authorized to enable playback. The player
is automatically authorized when it is connected to a
computer over a network. If not, please authorize this player
manually on the computer. The authorization (or permission)
method for access varies depending on the type of server
currently being connected. For more information on
authorizing this player, refer to the instruction manual of your
server.
Playing audio files stored on computers or
other components
Connecting to the LAN network
Be sure to connect computer or other components to the
network using the LAN interface before you use this function.
For details on the connections, see page 12.
Playback with Music Server
Important
• You cannot access a computer on a network while you are
logged onto a domain that is configured in a Windows
network environment. Instead of logging onto the domain,
log onto the local machine.
• There are cases where the time elapsed may not be
correctly displayed.
1 Press M.SERVER to select Music Server.
All available servers are shown on the display. “Please
wait” will be displayed until an available server is found.
2 Use / to select the server that the file you want to
play is stored on, then press ENTER.
The folders/files stored on the server are shown on the
display.
Page: 29
7
7
30
Playback with NETWORK features (Network audio player: N-P01)
You can perform the following sort functions by pressing
SORT, as long as your DLNA compatible digital media server
supports the Sort function.
Note
• Sort cannot be used on certain screens.
- If tracks are sorted by title, change to sorting by track
number.
- If tracks are sorted by track number, change to sorting by
title.
- If tracks are sorted by anything other than title/track,
change to sorting by track number.
3 Use / to select the file you want to play, then press
ENTER.
Playback starts.
• When the file you want to play is in the folder, select the
folder first.
• If you press RETURN during playback, the previous
(folders/files) screen will be displayed.
• To add your favorite file to Favorites function, press
+Favorite on the remote control.
• Check your network environment if “Please wait”
continues to be displayed.
Depending on the server or file, the operation will be as
follows.
-  button may not function.
-  and  buttons may not function, or may act the
same as the  and  buttons.
Using AirPlay to enjoy music
1 Confirm that the iPod touch, iPhone, iPad, iTunes and
this unit are connected to the same wired or wireless
network.
2 Play music on iPod touch, iPhone, iPad or iTunes.
3 During playback, tap the AirPlay icon ( ) displayed on
the iPod touch, iPhone, iPad or iTunes.
4 Select this unit’s name (“Friendly Name”) from the
available device list.
Operating AirPlay from an iPod/iPhone/iPad
1 Tap Music icon and start playing music.
Playback starts.
2 Tap AirPlay icon ( ).
3 Select N-P01.
AirPlay Password
Set the player with a password for AirPlay.
Under initial factory settings no password is set.
1 Press NET SERVICE  SETUP.
2 Select Network Setting  AirPlay Password.
3 Use /// to enter AirPlay Password, then press
ENTER.
/: Moves the adjusting digit.
/: Changes displayed character.
REPEAT: Switches character types.
CLEAR: Deletes one characters at a time.

Music Server
Song 1
Artist
Album
FLAC 44.1 kHz/24 bit
44:38 - 44:02
N-P01
Page: 30
31
Playback with NETWORK features (Network audio player: N-P01)
7
7
Installing Pioneer ControlApp
The Pioneer ControlApp must be installed on your mobile
device. For more information about your operating
environment, access the appropriate Website as noted below.
If using an iPhone or iPod touch
You can obtain from “App Store”.
If using an Android device
You can obtain from “Google Play”.
Using Pioneer ControlApp
If using Pioneer ControlApp for the first time, follow these
procedures to start the application.
1 Connect this unit to the network you normally use.
2 Connect your mobile device to the same network.
Confirm that Pioneer ControlApp is installed on your
mobile device.
3 Turn on the power to this unit.
4 Start Pioneer ControlApp on your mobile device.
5 Tap the “Download”.
When download is completed, the CONTROL screen will
be displayed.
NETWORK AUDIO PLAYER
SOURCE
N-P01
5 V 2.1 A
STANDBY/ON

l

 
Wired/Wireless
Wireless
Download
Page: 31
32
8
8 Additional information (Network audio player: N-P01)
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the
trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service
center or your dealer to carry out repair work.
• If the player does not operate normally due to external
effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal
operating conditions.
General
 When a button is pressed, the player does not respond.
 Set the player to the power standby mode and then turn it back
on.
 If the player still malfunctions, reset it (page 14).
 Settings you have made have been cleared.
 Was the power cord unplugged forcibly while this player’s
power was on? Be sure to press  NETWORK and wait for the
POWER indicator on the front panel display to turn off before
unplugging the power cord.
 This player cannot be operated with the remote control.
 Are you operating from far away? Operate from within a
distance of Operate within 7 m, 30° of the remote sensor on the
front panel (page 5).
 Is the remote control sensor exposed to direct sunlight or
strong artificial light from a fluorescent bulb, etc.? The remote
control signals may not be received properly if the remote
control sensor is exposed to direct sunlight or strong artificial
light from a fluorescent bulb, etc.
 Are the batteries dead? Replace the batteries (page 5).
 The player suddenly switches off.
 When the Auto Power Off function is working, the power will
automatically turn off. Check the setting for the Auto Power Off
function (page 14).
 The Bluetooth wireless technology device cannot be
connected or operated. Sound from the Bluetooth wireless
technology device is not emitted or the sound is
interrupted.
 Check that no object that emits electromagnetic waves in the
2.4 GHz band (microwave oven, wireless LAN device or
Bluetooth wireless technology apparatus) is near the player. If
such an object is near the player, set the player far from it. Or,
stop using the object emitting the electromagnetic waves.
 Check that the Bluetooth wireless technology device is not too
far from the player and that obstructions are not set between
the Bluetooth wireless technology device and the player. Set
the Bluetooth wireless technology device and the player so that
the distance between them is less than about 10 m* and no
obstructions exist between them.
* The line-of-sight transmission distance is an estimate. Actual
transmission distances supported may differ depending on
surrounding conditions.
 The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless
technology. Check the setting of the Bluetooth wireless
technology device.
 Check that pairing is correct. The pairing setting was deleted
from this player or the Bluetooth wireless technology device.
Reset the pairing.
 Check that the profile is correct. Use a Bluetooth wireless
technology device that supports A2DP profile and AVRCP
profile.
When a USB storage device is connected
 USB storage device is not recognized.
 Is the USB storage device properly connected? Connect the
device securely (all the way in).
 Is the USB storage device connected via a USB hub? This
player does not support USB hubs. Connect the USB storage
device directly.
 This is not a problem with this player. Turn the power off then
back on. Some USB storage devices may not be recognized
properly. This player only supports USB mass storage class
devices. Only the FAT16 and FAT32 file systems are supported.
Other file systems (ex. FAT, NTFS, etc.) are not supported. This
device does not support the use of external hard disc drives.
 Much time is required to recognize the USB storage device.
 What is the USB storage devices capacity? Some time may be
required to load the data when large capacity USB storage
devices are connected (this could take several minutes).
 Audio playback is undesirably stopped or disturbed.
 You may be using a USB 1.0 compatible device. We
recommend you use a USB 2.0 compatible device.
 File cannot be played.
 Is the file copyright-protected (by DRM)? Copyright-protected
files cannot be played.
 This is not a problem with this player. Files stored on a
computer cannot be played. It may not be possible to play
some files.
 When connecting the USB storage device, this player
switches off.
 Is Timer indicator flashing? The USB storage device does not
work or power consumption is too large. Disconnect the USB
storage device and turn this player on.
 The album or artist name is not displayed.
 Display of album names and artist names supports the
following formats.
MP3, WMA, Apple Lossless, FLAC, AIFF(*), DSD.
*In the case of AIFF, files with a sampling frequency of 176 kHz
or 192 kHz are not supported.
 Album art is not displayed.
 Display of album art is supported for MP3 and DSD (DSF only).
Embedded images are supported for JPEG only.
When an iPod/iPhone/iPad is connected
 Can’t operate the iPod/iPhone/iPad.
 Make sure the iPod/iPhone/iPad is connected correctly (refer
to Connect iPod/iPhone/iPad to the USB terminal on page 15).
Also, try disconnecting the iPod/iPhone/iPad then
reconnecting it.
 Confirm that the connected iPod/iPhone/iPad is supported by
this player.
 If the iPod/iPhone/iPad is experiencing a hangup, try resetting
the iPod/iPhone/iPad, and reconnect it to the player.
Network
 Cannot access to the network.
 The LAN cable is not firmly connected. Firmly connect the LAN
cable (page 12).
 Check that no restrictions have been placed on your router’s
MAC address.
 Confirm the network type (Network Setting  Network
Type). When Auto is selected in Network Type, the network
type is automatically switched between Wired and Wireless.
 Cannot access to the network using WPS.
 Network Type is set to Wired. Network Type must be set to
Wireless or Auto to use WPS connection. See page 24 to
change the network type. When using WPS connection, be
sure the LAN cable is not connected to the player and turn this
player on.
Page: 32
33
Additional information (Network audio player: N-P01)
13
8
8
 Cannot access to the component or computer connected
via network.
 Internet security software is currently installed in the
connected component. There are cases where a component
with Internet security software installed cannot be accessed.
 The audio component on the network which has been
switched off is switched on. Switch on the audio component
on the network before switching on this player.
 The component connected to the network is not properly set. If
the client is automatically authorized, you need to enter the
corresponding information again. Check whether the
connection status is set to “Do not authorize”.
 There are no playable audio files on the component connected
to the network. Check the audio files stored on the component
connected to the network.
 Wireless Accessory Configuration fails.
 If the iOS device is not connected via Wi-Fi, connect the iOS
device via Wi-Fi.
 If the iOS device and router are connected via 5 GHz, change
the connection between the iOS device and router to 2.4 GHz,
or use a different setting method.
 Playback does not start.
 The component is currently disconnected from this player or
the power supply. Check whether the component is properly
connected to this player or the power supply.
 The computer or Internet Radio is not properly operated.
 The corresponding IP address is not properly set. Switch on the
built-in DHCP server function of your router, or set up the
network manually according to your network environment
(page 12).
 The IP address is being automatically configured.
 The automatic configuration process takes time. Please wait.
 The audio files stored on components on the network, such
as a computer, cannot be played back.
 Windows Media Player 11 or Windows Media Player 12 is not
currently installed on your computer. Install Windows Media
Player 11 or Windows Media Player 12 on your computer
(page 29).
 Audio files were not recorded in a format playable on this
player. Check whether the audio files were recorded in a format
supported by this player (page 38).
 Audio files recorded in MPEG-4 AAC or FLAC are being played
back on Windows Media Player 11 or Windows Media Player
12. Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows Media
Player 12. Try using another server. Refer to the operation
manual supplied with your server.
 The component connected to the network is not properly
operated. Check whether the component is affected by special
circumstances or is in the sleep mode. Try rebooting the
component if necessary.
 The component connected to the network does not permit file
sharing. Try changing the settings for the component
connected to the network.
 The folder stored on the component connected to the network
has been deleted or damaged. Check the folder stored on the
component connected to the network.
 Network connections could be restricted due to the
computer’s network settings, security settings, etc. Check the
computer’s network settings, security settings, etc.
 Input of a password is requested when starting AirPlay.
 Enter the AirPlay password set during Wireless Accessory
Configuration or Network Setting.
 If you have forgotten the password, it is possible to reset it.
 Cannot access Windows Media Player 11 or Windows
Media Player 12.
 In case of Windows Media Player 11: You are currently logged
onto the domain through your computer with Windows XP or
Windows Vista installed. In case of Windows Media Player 12:
You are currently logged onto the domain through your
computer with Windows 7 or 8 installed. Instead of logging
onto the domain, log onto the local machine.
 Audio playback is undesirably stopped or disturbed.
 The audio file currently being played back was not recorded in
a format playable on this player. Check whether the audio file
was recorded in a format supported by this player. Check
whether the folder has been damaged or corrupted. Even audio
files listed as playable on this player may sometimes not be
played back or displayed (page 38).
 The LAN cable is currently disconnected. Connect the LAN
cable properly (page 12).
 There is heavy traffic on the network with the Internet being
accessed on the same network. Use 100BASE-TX to access the
components on the network.
 When in the DMR mode, depending on the external controller
being used, playback may be interrupted when a volume
operation is performed from the controller. In this case, adjust
the volume from the player or remote control.
 There is a connection routed through a wireless LAN on the
same network. There may be a shortage of bandwidth on the
2.4 GHz band used by the wireless LAN. Make wired LAN
connections not routed through a wireless LAN. Install away
from any devices emitting electromagnetic waves on the 2.4
GHz band (microwave ovens, game consoles, etc.). If this does
not solve the problem, stop using other devices that emit
electromagnetic waves.
 Cannot listen to Internet Radio stations.
 The firewall settings for components on the network are
currently in operation. Check the firewall settings for
components on the network.
 You are currently disconnected from the Internet. Check the
connection settings for components on the network, and
consult with your network service provider if necessary
(page 12).
 The broadcasts from an Internet Radio station are stopped or
interrupted. Some Internet radio stations on the list of Internet
Radio stations for this player (page 27) may occasionally not be
available for listening.
 The player only supports broadcast stations that use HTTP. It
may therefore be unable to playback certain broadcast
stations.
 Cannot pause at Music Server/DMR.
 For some DLNA server software/NAS, or file formats being
played, you many not be able to pause. Please contact the
DLNA server software manufacturer or NAS manufacturer that
you are using.
 Music Server (DLNA) album names and artist names are not
displayed.
 Metadata such as album names and artist names have to be
approved by the server and distributed to the player, which
depends on the NAS you are using and the specs of DLNA
server software.
Supported files differ depending on NAS and DLNA server
software. For more details, please contact the NAS
manufacturer or DLNA server software manufacturer.
 Music Server (DLNA) album art is either displayed or not
displayed.
 In the case of the Music Server, this depends upon the specs of
DLNA server software. Supported files differ depending on
DLNA server software. For more details, please contact the
DLNA server software manufacturer.
 This unit cannot be selected from the Spotify application.
 An Internet connection is required for both the mobile digital
device and this unit.
 Connect the mobile digital device by Wi-Fi to the wireless LAN
router of the same network as the one to which this unit is
connected.
Page: 33
34
Additional information (Network audio player: N-P01)
13
8
8
 A Spotify Premium account (for a charge) must be registered
on the Spotify application.
 When this unit is in standby, it cannot be selected from the
Spotify application.
 The sound of the Spotify audio stream is not produced.
 Check whether this unit is selected on the Spotify application.
 Check that contents are playing on the Spotify application.
 If the above does not solve the problem, turn this unit’s power
off then back on.
 This unit’s volume does not increase when the volume
slider in the Spotify application is raised.
 There is an upper limit to the volume to prevent the volume
from being too high accidentally. To raise the volume higher in
this case, do so by operating the remote control. When using
an application such as Pioneer ControlApp, the volume can
also be increased from the application.
 Playback continues on this unit when the Spotify
application is quit.
 The Spotify audio stream continues from this unit, even when
the Spotify application is quit. To operate again, relaunch the
Spotify application.
Wireless LAN
 Network cannot be accessed via wireless LAN.
 Is Network Type set to Auto and the LAN cable connected to
the player? Switch Network Type to Wireless or disconnect
the LAN cable from the player, then restart the player. If
Network Type is set to Auto and the LAN cable is connected
to the player, the player recognizes the Network Type as
Wired.
 This player and base receiver (wireless LAN router, etc.) are too
far apart or there is an obstacle between them. Improve the
wireless LAN environment by moving the player and base
receiver closer together, etc.
 There is a microwave oven or other device generating
electromagnetic waves near the wireless LAN environment.
Use the system in a place away from microwave ovens or
others device generating electromagnetic waves. Avoid using
devices generating electromagnetic waves as much as
possible when using the system with the wireless LAN.
 Multiple wireless devices are connected to the wireless LAN
router. When connecting multiple wireless devices, their IP
addresses must be changed.
 Wireless LAN connections cannot be established between the
player and base receiver (wireless LAN router, etc.). The player
must be set in order to establish wireless LAN connections.
See Connecting using wireless LAN on page 12.
 The IP address settings of the player does not match the
settings of the wireless LAN router, etc. Check the IP address
settings of the player (including the DHCP setting). If the
player’s DHCP setting is on, turn the player’s power off, then
turn the power back on. Check that the IP address of the player
matches the settings of the wireless LAN router, etc. If the
player’s DHCP setting is off, set an IP address matching the
network of the base receiver (wireless LAN router, etc.). For
example, if the wireless LAN router’s IP address is
“192.168.1.1”, set the player’s IP address to “192.168.1.XXX”
(*1), the subnet mask to “255.255.255.0”, the gateway and DNS
to “192.168.1.1”.
*1) Set the “XXX” in “192.168.1.XXX” to a number between 2
and 248 that is not assigned to other devices.
 The access point is set to conceal the SSID. In this case, the
SSID may not be displayed on the access point list screen. If
not, set the SSID, etc., by making the wireless LAN settings on
the player manually.
 The access point’s security settings use WEP 152-bit length
code key or shared key authentication. The player does not
support WEP 152-bit length code key or shared key
authentication.
 The SSID only supports use of single-byte alphanumeric
characters, together with the underbar and certain other
symbols. If using another character coding, the SSID must be
updated before making network settings. For more details
regarding SSID, consult your router’s operating instructions.
Setting quick start mode
Quick start mode significantly reduces the time required for
startup. It also allows the unit to power on automatically using
AirPlay, DLNA and Spotify application. Follow the steps below
to turn on quick start mode. Power consumption increases
when set to quick start mode when compared to regular
standby mode.
1 Press NET SERVICE, then press SETUP on the remote
control.
The Initial Setup screen is shown on the display.
2 Select ‘Option Setting’ from Initial Setup menu.
3 Select ‘Power Off Setting’ from Option Setting menu.
4 Select ‘Quick Start Mode’ from Power Off Setting menu.
5 To turn Quick Start Mode on, Use / to select ON,
then press ENTER.
To turn Quick Start Mode off, Use / to select OFF,
then press ENTER.
Page: 34
35
Additional information (Network audio player: N-P01)
13
8
8
Firmware Update
Use this procedure to update the player’s software. You can
update the software via a USB storage device.
Updating via a USB storage device is performed by
downloading the update file from a computer, reading this file
onto a USB storage device then inserting the USB storage
device into the USB port on the player’s front panel.
If an update file is provided on the Pioneer website, download
it onto your computer. When downloading an update file from
the Pioneer website onto your computer, the file will be in ZIP
format. Unzip the ZIP file before saving it on the USB storage
device. If there are any old downloaded files or downloaded
files for other models on the USB storage device, delete them.
Important
• DO NOT unplug the power cord during updating.
• When updating via a USB storage device, do not
disconnect the USB storage device.
1 Press iPod/USB to select iPod/USB as the input source.
iPod/USB is shown on the display.
2 Press SETUP.
The Initial Setup screen is displayed on the display.
3 Select Option Setting  Firmware Update  Start, then
press ENTER.
4 To update, select OK.
The updating screen appears and updating starts.
The player will reboot when the update is completed, and
the display will show the input function before the update.
Firmware Update messages
Firmware Update using Web browser
You can update this player’s firmware via Web browser.
Download the latest firmware at Pioneer website.
1 Be sure this player and your computer are connected to
the same wired or wireless network.
2 Launch Web browser on your computer.
3 Display the Network Setup menu.
For Safari
Press Bookmark icon ( ). Click Bonjour list (a), and
then select this player’s name (“Friendly Name”) (b) in
Bookmark.
If Bonjour list is not displayed, access the IP address
“http://(the player’s IP address)” from Safari.
Note
• The displayed name will change depending on the product
being used.
N-P01 *****, XN-P02 ***** or XN-P02DAB ***** will be
displayed. (“*****” is the lower three bytes of the MAC
address.)
Other than Safari
Enter “http://(the player’ IP address)” into your web
browser’s address bar.
Note
• Confirm the player’s IP address as follows:
1. Press NET SERVICE  SETUP.
2. Select System Info.
3. Confirm the IP field.
4 Click Network Setup  Firmware Update.
5 Press Start.
The firmware update prepare screen is displayed. If the
screen does not switch automatically, click Click here.
Firmware Update
Start
Cancel
Status messages Description
File Not Found. No update file was found on the USB
storage device. Store the file in the USB
storage device’s root directory.
a
b
N-P01 *****
N-P01 *****
Page: 35
36
Additional information (Network audio player: N-P01)
13
8
8
6 Browse the latest firmware on your computer (a) and
then press Upload (b).
The confirmation screen is displayed. If you continue the
firmware update, press Yes. Once the firmware update
process starts, you can’t stop it. Wait until the file is
uploaded (about one minute may be required depending
on your LAN connection environment).
7 The firmware upload status screen is displayed. Press
Ok.
“The upload process finished successfully.” will be shown
when the update is completed.
Unplug the the power cord from the AC outlet after the
update is completed.
Note
• This setting for the network has been confirmed for Mac OS
X 10.7 and Safari 5.1.
Resetting this player
Use this procedure to reset all player settings to the factory
default.
Important
• Disconnect all components connected to this player before
the operation.
1 Press NET SERVICE  SETUP.
The Initial Setup screen is displayed on the display.
2 Use / to select Factory Reset.
3 Select Start.
“Reset?” screen appears. Press ENTER to reset the
system.
All the settings will be reset to the factory default next
time the player is turned on.
Cautions on use
When moving this player
When moving this player, be sure to first disconnect the iPod/
iPhone/iPad, USB storage device, LAN cable or any other
equipment connected to the player. Then press  NETWORK,
wait for the power indicator on the front panel display to turn
off, then unplug the power cord. Damage may occur if the
player is transported, or when another device is connected to
the iPod/iPhone connector port, USB, LAN (10/100)
terminals.
Place of installation
Choose a stable place near the TV or stereo system being used
with this player. Do not place this player on top of a TV or color
monitor. Also install it away from cassette decks and other
devices easily affected by magnetic forces.
Avoid the following locations:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot places
• Places exposed to vibrations
• Places in which there is much dust or cigarette smoke
• Places exposed to soot, steam or heat (kitchens, etc.)
Do not place objects on this player.
Do not place any objects on top of this player.
Do not obstruct the ventilation holes.
Do not use this player on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Do not expose to heat.
Do not place this player on top of an amplifier or other
component that generates heat. When rack mounting it, to
avoid the heat given off by the amplifier or other audio
component, place it on a shelf below the amplifier.
Cleaning the product
• Unplug the power cord from the power outlet when
cleaning this player.
• Clean this player using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a soft
cloth, wring out thoroughly, wipe off the dirt, then wipe
again with a soft, dry cloth.
• Alcohol, thinner, benzene, insecticides, etc., could cause
the print or paint to peel off. Also, leaving rubber or vinyl
products in contact with this player for long periods of time
could mar the cabinet.
• When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.
About copyrights
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and
disassembly are prohibited.
a
b
Page: 36
37
Additional information (Network audio player: N-P01)
13
8
8
About network playback
The network playback function such as Internet Radio or
Music Server of this player uses the following technologies:
Windows Media Player
See Windows Media Player 11/Windows Media Player 12 on
page 29 for more on this.
DLNA
DLNA CERTIFIED™ Audio Player
The Digital Living Network Alliance (DLNA) is a cross-industry
organization of consumer electronics, computing industry
and mobile device companies. Digital Living provides
consumers with easy sharing of digital media through a wired
or wireless network in the home.
The DLNA certification logo makes it easy to find products
that comply with the DLNA Interoperability Guidelines. This
player complies with DLNA Interoperability Guidelines v1.5.
When a computer running DLNA server software or other
DLNA compatible device is connected to this player, some
setting changes of software or other devices may be required.
Please refer to the operating instructions for the software or
device for more information.
DLNA™, the DLNA Logo and DLNA CERTIFIED™ are
trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
Content playable over a network
• Even when encoded in a compatible format, some files may
not play correctly.
• Movie or Photo files cannot be played back.
• There are cases where you cannot listen to an Internet radio
station even if the station can be selected from a list of
radio stations.
• Some functions may not be supported depending on the
server type or version used.
• Supported file formats vary by server. As such, files not
supported by your server are not displayed on this player.
For more information check with the manufacturer of your
server.
Disclaimer for Third Party Content
Access to content provided by third parties requires a high
speed internet connection and may also require account
registration and a paid subscription.
Third party content services may be changed, suspended,
interrupted, or discontinued at any time without notice, and
Pioneer disclaims any liability in connection with such
occurrences.
Pioneer does not represent or warrant that content services
will continue to be provided or available for a particular period
of time, and any such warranty, express or implied, is
disclaimed.
About playback behavior over a network
• Playback may stall when the computer is switched off or
any media files stored on it are deleted while playing
content.
• If there are problems within the network environment
(heavy network traffic, etc.) content may not be displayed or
played properly (playback may be interrupted or stalled).
For best performance, a 100BASE-TX connection between
player and computer is recommended.
• If several clients are playing simultaneously, as the case
may be, playback is interrupted or stalled.
• Depending on the security software installed on a
connected computer and the setting of such software,
network connection may be blocked.
Pioneer is not responsible for any malfunction of the player
and/or the Music Server features due to communication
error/malfunctions associated with your network connection
and/or your computer, or other connected equipment. Please
contact your computer manufacturer or Internet service
provider.
Windows Media is either a registered trademark or trademark of
Microsoft Corporation in the United States and/or other
countries.
This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a license
from Microsoft Licensing, Inc.
Microsoft®
, Windows®
8, Windows®
7, Windows®
Vista,
Windows®
XP, Windows®
2000, Windows®
Millennium Edition,
Windows®98, and WindowsNT® are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Authorizing this player
In order to be able to play with Music Server, this player must
be authorized. This happens automatically when the player
makes a connection over the network to the computer. If not,
please authorize this player manually on the computer.
The authorization (or permission) method for access varies
depending on the type of server currently being connected.
For more information on authorizing this player, refer to the
instruction manual of your server.
Apple Lossless Audio Codec
Copyright © 2011 Apple Inc. All rights reserved.
Licensed under the Apache License, Version 2.0. You may
obtain a copy of the License at http://www.apache.org/
licenses/LICENSE-2.0
Page: 37
38
Additional information (Network audio player: N-P01)
13
8
8
FLAC
FLAC Decoder
Copyright c 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007,
2008, 2009 Josh Coalson
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of the Xiph.org
Foundation nor the names of its contributors may be used
to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
About playable music file formats
The USB and Music Server function of this player supports the
following music file formats.
• Note that some file formats are not available for playback
although they are listed as playable file formats. Also, the
compatibility of file formats varies depending on the type
of server. Check with your server to ensure the
compatibility of file formats supported by your server.
• Internet radio playback may be affected by the Internet
communications environment, and in this case playback
may not be possible even with the file formats listed here.
• With MP3, WAV, AAC, FLAC, AIFF and Apple Lossless files,
when music files with the same format, sampling
frequency, quantization bit number and number of
channels are played successively, they are played with no
gap.
- Make sure the gap is at the minimum when using MP3 or
AAC. If you are concerned about the gap, please use
WAV or FLAC files.
- Gapless playback is not possible when the format is
being converted (transcoded) by the server.
- Gapless playback is not possible in the DMR mode.
Category Extension Stream
MP3a .mp3 MPEG-1/2
Audio
Layer-3
Sampling
frequency
32 kHz, 44.1 kHz,
48 kHz
Quantization
bitrate
16 bit
Channel 2 ch
Bitrate 8 kbps to 320 kbps
VBR/CBR Supported/
Supported
WAV .wav LPCM Sampling
frequency
USB/Music Server
(Wired): 32 kHz,
44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Music Server
(Wireless): 32 kHz,
44.1 kHz, 48 kHz
Quantization
bitrate
16 bit, 24 bit
Channel 2 ch
WMA .wma WMA2/7/
8/9b
Sampling
frequency
32 kHz, 44.1 kHz,
48 kHz
Quantization
bitrate
16 bit
Channel 2 ch
Bitrate 5 kbps to 320 kbps
VBR/CBR Supported/
Supported
AAC .m4a
.aac
MPEG-4
AAC LC
MPEG-4
HE AAC
(aacPlus
v1/2)
Sampling
frequency
32 kHz, 44.1 kHz,
48 kHz
Quantization
bitrate
16 bit
Channel 2 ch
Bitrate 16 kbps to 320 kbps
VBR/CBR Supported/
Supported
Category Extension Stream
Page: 38
39
Additional information (Network audio player: N-P01)
13
8
8
a “MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.”
b Files encoded using Windows Media Codec 9 may be
playable but some parts of the specification are not
supported; specifically, Pro, Lossless, Voice.
c Uncompressed FLAC files are not supported. Pioneer does
not guarantee playback.
About iPod/iPhone/iPad
“Made for iPod,” “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect wireless
performance.
USB works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s,
iPhone 4, iPhone 3GS, iPad Air, iPad (3rd and 4th generation),
iPad 2, iPad mini with Retina Display, iPad mini, iPod touch
(1st through 5th generation) and iPod nano (3rd through 7th
generation).
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion or later, and PC
with iTunes 10.2.2 or later.
Apple, AirPlay, iPad, iPhone, iPod, iPod nano, iPod shuffle, iPod
touch, Retina, iTunes, Safari, Bonjour, Mac, Mac OS and OS X
are trademarks of Apple Inc., registered in the U.S. and other
countries.
iPad Air, iPad mini are trademarks of Apple Inc.
The AirPlay logo is a trademark of Apple Inc.
App Store is a service mark of Apple Inc.
Apple
Lossless
.m4a
.mp4
Apple
Lossless
Sampling
frequency
USB/Music Server
(Wired): 32 kHz,
44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz
Music Server
(Wireless): 32 kHz,
44.1 kHz, 48 kHz
Quantization
bitrate
16 bit, 24 bit
Channel 2 ch
FLACC .flac FLAC Sampling
frequency
USB/Music Server
(Wired): 32 kHz,
44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Music Server
(Wireless): 32 kHz,
44.1 kHz, 48 kHz
Quantization
bitrate
16 bit, 24 bit
Channel 2 ch
Bitrate —
AIFF .aiff
.aif
AIFF Sampling
frequency
USB/Music Server
(Wired): 32 kHz,
44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Music Server
(Wireless): 32 kHz,
44.1 kHz, 48 kHz
Quantization
bitrate
16 bit, 24 bit
Channel 2 ch
Category Extension Stream
DSD .dff
.dsf
DSDIFF
DSF
Sampling
frequency
USB/Music Server
(Wired): 2.8224
MHz
Music Server
(Wireless): No
Quantization
bitrate
USB/Music Server
(Wired): 1 bit
Music Server
(Wireless): No
Channel USB/Music Server
(Wired): 2 ch
Music Server
(Wireless): No
Category Extension Stream
Page: 39
40
Additional information (Network audio player: N-P01)
13
8
8
About aptX
© 2013 CSR plc and its group companies. The aptX® mark and
the aptX logo are trade marks of CSR plc or one of its group
companies and may be registered in one or more jurisdictions.
About Wi-Fi®
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi
Alliance.
The Wi-Fi Protected Setup Indentifer Mark is a mark of the Wi-
Fi Alliance.
About Spotify
The Spotify software is subject to third party licenses found
here:
www.spotify.com/connect/third-party-licenses
Page: 40
41
9
9 Control and display (Stereo receiver: SX-P01, SX-P01DAB)
How to use the stereo receiver (SX-P01, SX-P01DAB) supplied with the XN-P02 and XN-P02DAB.
Front panel
Stereo receiver
1 /I STANDBY/ON
Press to turn on and off the stereo receiver (page 44).
2 SOURCE
Use to select the input source for the stereo receiver (page 45).
3 DIRECT indicator
Lights when the DIRECT function is on (page 45).
4 TIMER indicator
Lights when the timer is set (page 46).
5 Remote sensor
Receives signals from the remote control.
6 VOLUME control
Use to set the listening volume (page 44).
7 PHONES (headphone) socket
Connect headphones. When the headphones are connected, there is no sound output
from the speakers (page 45).
8 PRESET
Use to select preset radio stations (page 47).
9 DIRECT
Use to listen to the sound source in the original sound quality (page 45).
1
8
7
5 6
4
3
2
9
Page: 41
42
10
10 Connecting your equipment (Stereo receiver: SX-P01, SX-P01DAB)
Connecting your equipments (XN-P02, XN-P02DAB only)
Before making or changing the connections, turn off the power and disconnect the power cord from the AC outlet.
Antenna connection
Supplied FM wire antenna (SX-P01), DAB/FM wire
antenna (SX-P01DAB):
Connect the supplied FM wire antenna or DAB/FM wire
antenna to the FM socket or DAB/FM socket, and position the
wire antenna in the direction where the strongest signal can
be received.
External FM wire antenna:
Use an external FM wire antenna (75 ohms coaxial cable) for
better reception. When an external FM wire antenna is used,
disconnect the supplied FM wire antenna.
Note
• Placing the wire antenna on the unit or near the AC power
lead may cause noise pickup. Place the wire antenna away
from the unit for better reception.
Speaker connection
Use speakers with an impedance of 4 ohms as lower
impedance speakers can damage the unit.
1 Loosen the knobs of the speaker output terminals.
2 Insert the speaker cable wires into each of the terminal
post holes (positive (+) cable to the red knob, and
negative (–) cable to the black knob), then tighten the
knobs.
3 Connect the other ends of the cables to the terminals of
speakers (make sure the positive and negative (+/–)
terminals on the speakers match those on the stereo
receiver).
CAUTION
• These speaker terminals carry HAZARDOUS LIVE voltage.
To prevent the risk of electric shock when connecting or
disconnecting the speaker cables, disconnect the power
cord before touching any uninsulated parts.
• Do not mistake the right and the left channels. The right
speaker is the one on the right side when you face the unit.
• Do not let the bare speaker wires touch each other.
• Make sure that all the bare speaker wire is twisted together
and inserted fully into the speaker terminal. If any of the
bare speaker wire touches the back panel, it may cause the
power to cut off as a safety measure.
ANTENNA
AC IN
Right speaker
FM wire antenna
SX-P01
Wall socket (AC 220 V to
230 V, 50 Hz)
Monaural mini-plug
cord (without resistor)
SX-P01DAB: Connect
the DAB/FM wire
antenna to the DAB/
FM socket.
To CONTROL OUT
socket of other
Pioneer component
Left speaker
Page: 42
43
Connecting your equipment (Stereo receiver: SX-P01, SX-P01DAB)
10
10
Using other subwoofer
You can connect a subwoofer with an amplifier to the
SUBWOOFER OUT socket.
Note
• No sound is output from the subwoofer without a built-in
amplifier.
Connecting a network audio player (N-P01)
Connect the stereo receiver (SX-P01, SX-P01DAB) and
network audio player (N-P01) using the supplied remote
control cable and RCA audio cable.
Note
• To select NETWORK input;
On remote control: Press the NETWORK.
On stereo receiver: Turn the SOURCE knob until NETWORK
is displayed in the front panel display.
• When the stereo receiver (SX-P01, SX-P01DAB) and
network audio player (N-P01) are connected using the
remote control cable, the stereo receiver remote control
signal receiver will not function. Point the remote control at
the remote control signal receiver on the network audio
player.
• When connecting to the control connector, you must also
connect the audio cable (analog connection). Only
connecting to the control connector will not allow for
correct system control.
• Connecting the remote control cable will allow the Pioneer
ControlApp to be used, providing simple control over the
stereo receiver (SX-P01, SX-P01DAB) via the network audio
player (N-P01). Refer to page 31 for details of the Pioneer
ControlApp.
• If the network audio player’s quick start setting is Off then
you will be unable to control the stereo receiver or CD
player.
Turn the network audio player’s quick start setting On and
you will be able to control them.
Connecting digital audio device
You can connect a digital audio device to the stereo receiver
using an optical or coaxial cable (commercially available).
Note
• To select digital input;
On remote control: Press the DIG IN 1/2 button repeatedly
until DIGITAL IN 1 (for optical input) or DIGITAL IN 2 (for
coaxial input) is displayed in the front panel display.
On stereo receiver: Turn the SOURCE knob until DIGITAL
IN 1 (for optical input) or DIGITAL IN 2 (for coaxial input) is
displayed in the front panel display.
• Digital signal formats that can be input to the stereo
receiver include linear PCM signals with sampling rate and
quantitative bits up to 192 kHz/24 bits. (Depending on the
connected device and environment, operation may not be
successful).
ANTENNA
Stereo receiver
(SX-P01 for
example)
Audio cable
(commercially
available)
To audio input
socket
To SUBWOOFER OUT
socket
Commercially
available subwoofer
(amplifier built in)
L
R
DIGITAL
OUT
CONTROL
OPTICAL
WLAN ANTENNA
LAN (10/100)
AUDIO
OUT
OUT
N-P01
SX-P01 or SX-P01DAB
DIGITAL OUT
DIGITAL OUT
COAXIAL
OPTICAL
Coaxial cable
(commercially available)
Optical cable (commercially available)
Digital audio device
Stereo receiver
Digital audio device
Page: 43
44
11
11 Getting started (Stereo receiver: SX-P01, SX-P01DAB)
To turn the power on
Press the I SYSTEM ON button on the remote control to turn
on both of the stereo receiver and network audio player.
To turn on the stereo receiver only:
Press the  RECEIVER button on the remote control or the /
I STANDBY/ON button on the stereo receiver.
Setting the clock
In this example, the clock is set to the 24-hour (0:00) display.
1 Turn on the stereo receiver.
Refer to To turn the power on above for details.
2 Press the CONTROL RCV button on the remote control.
3 Press the CLOCK button on the remote control.
The current day and time are displayed.
The default setting (Sun 0:00) is displayed when the first time
you set the clock.
4 Press ENTER button.
5 Use / to set the day, then press ENTER.
6 Use / to select 24-hour or 12-hour display, then
press ENTER.
7 Use / to set the hour, then press ENTER.
8 Use / to set the minute, then press ENTER to
confirm.
Note
• Press the CLOCK or RETURN button to exit the setting
mode without setting the clock.
To confirm the time display:
Press the CLOCK button. The current time and day are
displayed in the front panel display of the stereo receiver for 5
seconds.
Note
• The current time and day display is canceled if;
- the volume is adjusted.
- the SETUP, BASS +/–, TREBLE +/–, DIRECT, or SLEEP
button is pressed.
- the stereo receiver is turned off.
- the input source for the stereo receiver is changed.
To readjust the clock:
Perform “Setting the clock” from step 1.
Note
• If the AC power cord of the stereo receiver is disconnected
from the wall socket, the clock setting is cleared. Set the
clock.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents.
Refer to Resetting this player on page 36 for details.
2 Perform “Setting the clock” from step 1 onwards.
General functions
Display brightness control
Press the CONTROL RCV button on the remote control.
Press DIMMER button to dim the display brightness. The
brightness can be controlled in four steps.
Volume control
Press the VOLUME +/– on the remote control to increase or
decrease volume, or turn the VOLUME knob on the stereo
receiver to the right to increase volume, and to the left to
decrease the volume.
CAUTION
• The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It is
advisable to avoid exposure to high volume levels. Do not
turn the volume on to full at switch on. Listen to music at
moderate levels. Excessive sound pressure from earphones
and headphones can cause hearing loss.
Note
• If you turn off and on the stereo receiver with the volume set
to 61 or higher, the volume starts at 60.
• When the DIRECT function is off, the volume can be set
from minimum to 60.
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
CLOCK
TIMER SLEEP DIMMER
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
The time is displayed in the 24-hour
display format (0:00 – 23:59).
The time is displayed in the 12-hour
display format (AM 0:00 – PM
11:59).
CLOCK
TIMER SLEEP DIMMER
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
SYSTEM ON RECEIVER CD NETWORK
CONTROL
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
Page: 44
45
Getting started (Stereo receiver: SX-P01, SX-P01DAB)
11
11
Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the
volume.
DIRECT function
Press the DIRECT button on the remote control or on the
stereo receiver to listen to the sound source in the original
sound quality. The DIRECT indicator lights in the front panel
display of the stereo receiver when the DIRECT function is on.
Press the DIRECT button again to cancel the DIRECT
function.
Note
• If the DIRECT function is turned off when the volume is set
to 61 or higher, the volume is automatically set to 60.
Bass control
Press the BASS + button on the remote control to emphasize
the bass, and the BASS– button to de-emphasize it.
Note
• This function is not available when the DIRECT function is
on.
Treble control
Press the TREBLE + button on the remote control to
emphasize the treble, and the TREBLE– button to de-
emphasize it.
Note
• This function is not available when the DIRECT function is
on.
Input selection
The input source for the stereo receiver can be selected by
pressing each input selection button (CD/USB, TUNER,
NETWORK, and DIG IN 1/2) on the remote control, or turning
the SOURCE knob on the stereo receiver.
Note
• If pressing the INPUT button on the remote control
repeatedly or turning the SOURCE knob on the stereo
receiver to the right, the input source is switched in the
following order.
If turning the SOURCE knob to the left, the order is reversed.
• The backup function will memorize the input mode and
restore it in case of a power failure or that the AC power
cord is disconnected.
Headphones
Plug headphones (commercially available) into the PHONES
socket on the stereo receiver.
• Do not turn the volume on to full at switch on and listen to
music at moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
• Before plugging in or unplugging the headphone, reduce
the volume.
• Be sure your headphone has a 3.5 mm diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
• Plugging in the headphone disconnects the speakers
automatically.
Auto power down setup
The unit turns off automatically if no operations are performed
for specified period of time.
• Default setting: 6H
1 Press the CONTROL RCV button on the remote control.
2 Press the SETUP button.
3 Press / to specify the amount of time.
You can select 2, 4 or 6 hours, or off (if no automatic
shutoff is desired).
4 Press the ENTER button.
Note
• Press the RETURN button to exit the setting mode without
setting the auto power down function.
CAUTION
• If setting the auto power down for the stereo receiver, both
of the stereo receiver and CD player are automatically
turned off after the specified period of time has elapsed. If
setting the auto power down for the CD player, only the CD
player is automatically turned off after the specified period
of time has elapsed.
TUNER
DIGITAL IN 1
CD/USB NETWORK
DIGITAL IN 2
Page: 45
46
Getting started (Stereo receiver: SX-P01, SX-P01DAB)
11
11
Timer and sleep operation
Setting the wake-up timer
Timer playback:
The unit turns on and plays the desired source (CD, DAB (SX-
P01DAB only), TUNER PRESET, NETWORK, DIGITAL IN 1, or
DIGITAL IN 2) at a preset time.
Before setting timer:
• Check that the clock is set to the correct time (Setting the
clock on page 44). If it is not set, you cannot use the timer
function.
• For timer playback: Load a disc to be played.
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the CONTROL RCV button on the remote control.
3 Press the TIMER button.
4 Press / button to select ‘Timer Set’ within ten
seconds, then press ENTER.
When setting the wake-up timer for the first time, only
‘Timer Set’ is available.
5 Select the source you want to play.
Use / button to select CD, DAB (SX-P01DAB only),
TUNER PRESET, NETWORK, DIGITAL IN 1, or DIGITAL
IN 2.
6 Press ENTER.
If TUNER PRESET is selected in step 5, use / button
to select a preset.
7 Set the day(s) of the week.
Use / button to choose the day(s).
The timer can be set as follows.
8 Press ENTER.
9 Set the switch-on time.
Use /button to set the hour, then press ENTER.
Set the minute in the same way, and then press ENTER.
10Set the switch-off time.
Set as above, and then press ENTER.
11Use / button to set the volume.
The volume level that can be set for the wake-up timer is
up to 60.
12Press ENTER.
The TIMER indicator lights, and the settings can be
confirmed in the front panel display of the stereo receiver.
13Turn off the stereo receiver.
Refer to To turn the power on on page 44 for details.
Turning the wake-up timer on/off
If you have already set the wake-up timer, you can switch it on/
off.
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the CONTROL RCV button on the remote control.
3 Press the TIMER button.
4 Press / button to select ‘Timer On’ or ‘Timer Off’
within ten seconds, then press ENTER.
When ‘Timer On’ is selected, the timer indicator lights,
and the settings can be confirmed in the front panel
display of the stereo receiver.
5 When ‘Timer On’ is selected, turn off the stereo receiver.
Refer to To turn the power on on page 44 for details.
Reusing the memorised timer setting
The timer setting will be memorised once it is entered. To
reuse the same setting, perform the following operations.
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the CONTROL RCV button on the remote control.
3 Press the TIMER button.
4 Press / button to select ‘Timer Call’ within ten
seconds, then press ENTER.
The TIMER indicator lights, and the settings can be
confirmed in the front panel display of the stereo receiver.
Sleep operation
Press SLEEP to change the amount of time before the stereo
receiver switches into standby (30 min. – 60 min. – 90 min. –
Off).
• When the sleep timer is set, “ ” is displayed in the front
panel display of the stereo receiver.
• You can check the remaining sleep time at any time by
pressing SLEEP once.
SYSTEM ON RECEIVER CD NETWORK
CONTROL
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
CLOCK
TIMER SLEEP DIMMER
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
SYSTEM ON RECEIVER CD NETWORK
CONTROL
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
CLOCK
TIMER SLEEP DIMMER
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
EVERYDAY SUNDAY MONDAY
TUESDAY WEDNESDAY THURSDAY
FRIDAY SATURDAY MON-FRI
TUE-SAT SAT-SUN
Page: 46
47
12
12 Using the tuner (Stereo receiver: SX-P01, SX-P01DAB)
Tuning to a FM radio station
Tune to FM radio broadcasts using the automatic (search)
and manual (step) tuning functions. Once you are tuned to a
station, you can memorize the frequency for recall later.
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the TUNER button on the remote control to select
the TUNER input.
You can also select the TUNER input by turning the
SOURCE knob on the stereo receiver.
3 Press the CONTROL RCV button on the remote control.
4 Press the BAND button to change the band, if necessary.
SX-P01: Each press switches the band between FM stereo
and FM mono.
SX-P01DAB: Each press switches the band between FM
(stereo or mono) and DAB (for details on DAB, see
Listening to the DAB (XN-P02DAB only) on page 49).
5 Tune to a station.
Automatic tuning
To search for stations in the currently selected band,
press and hold TUNE / for about a second. The stereo
receiver will start searching for a station, and stop when it
has found one. Repeat to search for other stations.
Manual tuning
To change the frequency one step at a time, press
TUNE /.
High speed tuning
Press and hold TUNE / for high speed tuning.
Release the button at the frequency you want.
– Lights when a normal broadcast channel.
– Lights when a stereo FM broadcast is being received in
auto stereo mode.
Improving FM sound
If the or indicator does not light when tuning to an FM
station because the signal is weak, set the stereo receiver to
the mono reception mode.
1 Press the CONTROL RCV button on the remote control.
2 Press BAND to select FM MONO.
This should improve the sound quality and allow you to
enjoy the broadcast.
Saving station presets
If you often listen to a particular radio station, it is convenient
to have the stereo receiver store the frequency for easy recall
whenever you want to listen to that station. This saves the
effort of manually tuning in each time. This unit can memorize
up to 40 stations.
1 Tune to a station you want to memorize.
See Tuning to a FM radio station above for more on this.
2 Press the CONTROL RCV button on the remote control.
3 Press TUNER EDIT.
The preset number is blinking.
4 Press PRESET / to select a station preset number.
You can also use the numeric buttons.
5 Press ENTER.
The preset number stops blinking and the stereo receiver
stores the station.
Note
• If the stereo receiver is left disconnected from the AC power
outlet for over a month, the station memories will be lost
and will have to be reprogrammed.
• Stations are stored in stereo. Even if the station is stored in
the FM MONO mode, is displayed when recalled.
Listening to station presets
Preset stations beforehand. See Saving station presets above
if stations have not been preset.
1 Press the CONTROL RCV button on the remote control.
2 Press PRESET / to select the station preset you
want.
You can also use the numeric buttons or the PRESET
button on the stereo receiver.
Naming preset stations
For easier identification, you can name all of your preset
stations.
1 Choose the station preset you want to name.
See Listening to station presets above for how to do this.
2 Press the CONTROL RCV button on the remote control.
3 Press TUNER EDIT twice.
The cursor at the first character position blinks on the
display.
4 Input the name you want.
Choose a name up to eight characters long.
• Use / to select character position.
• Use / to select characters.
• The name is stored when ENTER is pressed.
SYSTEM ON RECEIVER CD NETWORK
CONTROL
CLOCK
TIMER SLEEP DIMMER
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
DISPLAY
iPod CONTROL
TOP
MENU
TUNE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
REPEAT
SHUFFLE
PLAY MODE
FOLDER
DISPLAY
iPod CONTROL
TOP
MENU
1 2 3 PGM
4 5 6
7 8 9
0
10 100
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
Page: 47
48
Using the tuner (Stereo receiver: SX-P01, SX-P01DAB)
12
12
Introduction to RDS
Radio Data System (RDS) is a system used by most FM radio
stations to provide listeners with various kinds of
information—the name of the station and the kind of show
they are broadcasting, for example.
One feature of RDS is that you can search by type of program.
For example, you can search for a station that is broadcasting
a show with the program type, JAZZ.
You can search the following program types:
Note
• In addition, there are three other program types, ALARM,
ALARMTST, and NO TYPE. ALARM and ALARMTST are
used for emergency announcements. ‘NO TYPE’ appears
when a program type cannot be found.
Searching for RDS programs
You can search for a program type listed above.
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the TUNER button on the remote control to select
the TUNER input.
You can also select the TUNER input by turning the
SOURCE knob on the stereo receiver.
3 Press the CONTROL RCV button on the remote control.
4 Press the BAND button to select the FM band.
RDS is only possible in the FM band.
5 Press PTY.
6 Press PRESET / to select a program type.
7 Press ENTER to search for the program type.
The system starts searching through the station presets
for a match, and stops when it finds one. Repeat to search
for other stations.
If “NO PTY” is displayed it means the tuner could not find
that program type at the time of the search.
• RDS searches station presets only. If no stations have been
preset, or if the program type could not be found among the
station presets “NO PTY” is displayed. “FINISH” means the
search is complete.
Displaying RDS information
Use the RDS DISP or DISPLAY button to display the different
types of RDS information available.
1 Press the RDS DISP button on the remote control.
2 Press the RDS DISP or DISPLAY button for RDS
information.
Each press changes the display as follows:
• Program Service Name (PS) – The name of the radio
station.
• Program Type (PTY) – This indicates the kind of program
currently being broadcast.
• Radio Text (RT) – Messages sent by the radio station. For
example, a talk radio station may provide a phone number
as RT.
• Current tuner frequency (FREQ)
Note
• If any noise is picked up while displaying the RT scroll,
some characters may be displayed incorrectly.
• If you see “NO TEXT” in the RT display, it means no RT data
is sent from the broadcast station. If no PS data, “NO
NAME” is displayed.
• In the PTY display, “NO PTY” may be shown.
NEWS – News
AFFAIRS – Current affairs
INFO – General information
SPORT – Sport
EDUCATE – Educational
DRAMA – Radio plays, etc.
CULTURE – National or
regional culture, theater, etc.
SCIENCE – Science and
technology
VARIED – Usually talk-based
material, such as quiz shows
or interviews.
POP M – Pop music
ROCK M – Rock music
EASY M – Easy listening
LIGHT M – ‘Light’ classical
music
CLASSICS – ‘Serious’
classical music
OTHER M – Music not fitting
above categories
WEATHER – Weather reports
FINANCE – Stock market
reports, commerce, trading,
etc.
CHILDREN – Programs for
children
SOCIAL – Social affairs
RELIGION – Programs
concerning religion
PHONE IN – Public
expressing their views by
phone
TRAVEL – Holiday-type travel
rather than traffic
announcements
LEISURE – Leisure interests
and hobbies
JAZZ – Jazz
COUNTRY – Country music
NATION M – Popular music
in a language other than
English
OLDIES – Popular music from
the ’50s and ’60s
FOLK M – Folk music
DOCUMENT – Documentary
SYSTEM ON RECEIVER CD NETWORK
CONTROL
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
DISPLAY
iPod CONTROL
TOP
MENU
1 2 3 PGM
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
Page: 48
49
Using the tuner (Stereo receiver: SX-P01, SX-P01DAB)
12
12
Listening to the DAB (XN-P02DAB only)
DAB (Digital Audio Broadcasting) is a digital transmission
system where audio signals are converted to digital signals for
broadcasting.
DAB broadcasts a group of data called multiplex (ensemble)
which may contain one or more stations (services). Each
station contains a primary service and there may be one or
more secondary services.
This allows several programs or services to be transmitted on
a single frequency.
Selecting DAB
1 Turn on the stereo receiver.
Refer to To turn the power on on page 44 for details.
2 Press the TUNER button on the remote control to select
the TUNER input.
You can also select the TUNER input by turning the
SOURCE knob on the stereo receiver.
3 Press the CONTROL RCV button on the remote control.
4 Press the BAND button repeatedly to select “DAB”.
Using the auto scan function manually
Using DAB for the very first time
The very first time you use DAB, press the AUTO TUNE button
to run the Auto Scan.
If a new DAB station is introduced, or you move to a new area,
you can run the Auto Scan function again.
1 Select DAB.
See Selecting DAB above for more on this.
2 Press the CONTROL RCV button on the remote control.
3 Press the AUTO TUNE button.
Selecting DAB stations
1 Select DAB.
See Selecting DAB above for more on this.
2 Press the CONTROL RCV button on the remote control.
3 Press the TUNE / button to select a DAB service.
4 Press the ENTER button to listen to the service.
The station is tuned.
While the primary service is selected, brackets < > are
displayed. While the secondary service is selected,
brackets ( ) are displayed.
If you select a station that cannot be received properly,
“DAB No Tuned” is displayed.
Displaying DAB radio information
1 Select DAB.
See Selecting DAB on page 49 for more on this.
2 Press the CONTROL RCV button on the remote control.
3 Press the RDS DISP or DISPLAY button repeatedly to
display information about the selected DAB station.
Program Type
Displays the type of program.
DAB SIGNAL
SERVICES
MULTIPLEX
(ENSEMBLE)
SERVICES
COMPONENTS
(STATIONS)
SYSTEM ON RECEIVER CD NETWORK
CONTROL
NET
CD
RCV
SYSTEM OFF
TREBLE
BASS
BT AUDIO
iPod/USB
DIG IN 1/2
M.SERVER
CD/USB CD USB
BAND FAVORITES
TUNER
DIRECT
NETWORK NET SERVICE
VOLUME
RETURN
MUTE
PTY
AUTO TUNE
SETUP
TUNER EDIT
DISPLAY
iPod CONTROL
TOP
MENU
1 2 3 PGM
TUNE
P
R
E
S
E
T
TUNE
ENTER
RDS DISP
P
R
E
S
E
T
BBC
DAB
News
Station name
DAB
Scanning...
BBC
(BBC5Live)
BBC
(BBC5Live)
DAB No Tuned
DAB No Tuned
BBC
News
Page: 49
50
Using the tuner (Stereo receiver: SX-P01, SX-P01DAB)
12
12
SNR (Signal Noise Rate)
Noise may be generated and reception quality may become
poor according to Signal Noise Rate. If reception quality is
poor, move the antenna in different directions to find a
position where the good rate is displayed.
DLS (Dynamic Label Segment)
When tuned to a station which is broadcasting DLS text data,
the text will scroll across the display.
Audio Mode
Displays the audio mode (stereo or mono).
Frequency
Displays the frequency of the current multiplex.
Multiplex Name
Displays the name of the current multiplex.
Bitrate
Displays the bit rate.
DAB setup
1 Press the CONTROL RCV button on the remote control.
2 Press the TOP MENU button.
3 Press the / button to select the item to be set, then
press the ENTER button.
The following settings are available for DAB.
DRC
The DRC (Dynamic Range Control) function lets you change
the dynamic range of the received sound depending on the
content of the broadcast so that the sound is easier to hear
even when the volume is low.
Press the / button to select the following options, and
then press the ENTER button.
DRC:Off : DRC is switched off.
Any DRC level broadcast will be ignored. This is the default
setting.
DRC:On : Applies DRC level as sent with the broadcast.
Component Reset
Deletes all the stations.
While “Reset: Yes?” appears, press the ENTER button.
SNR:100
BBC
Scroll
All the late
BBC
BBC
DAB Stereo
FREQ:239.200MHz
BBC
BBC Station
BBC
BITRATE:192kbps
BBC

Question & answers

There are no questions about the Pioneer XN-P02-K yet.

Ask a question about the Pioneer XN-P02-K

Have a question about the Pioneer XN-P02-K but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer XN-P02-K. Please make sure that you describe your difficulty with the Pioneer XN-P02-K as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.