Pioneer X-SMC1-S manual

View a manual of the Pioneer X-SMC1-S below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Hi-Fi system
  • Model/name: X-SMC1-S
  • Filetype: PDF
  • Available languages: Swedish, Danish, Norwegian, Finnish, Indonesian, English, French, Spanish

Table of Contents

Page: 1
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the AC adapter label.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light) D3-4-2-1-7c*_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 10 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period. K041_A1_En
When using this product, confirm the safety
information shown on the bottom of the unit and the
AC adapter label. D3-4-2-2-4_B1_En
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007.
CLASS 1 LASER PRODUCT
D58-5-2-2a_A1_En
X-SMC1_SYXZT8_En.book 2 ページ 2011年6月15日 水曜日 午後4時44分
Page: 2
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation). D3-4-2-2-2a*_A1_En
Information for users on collection and disposal of old equipment and used batteries
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Symbol examples
for batteries
Symbol for
equipment
Pb
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation). D3-4-2-2-1a_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
AC adapter CAUTION
• Make sure to grasp the body of the AC adapter when
removing it from the power outlet. If you pull the
power cord, it may become damaged which could
lead to fire and/or electrocution.
• Do not attempt to plug in or remove the AC adapter
with wet hands. This may result in electrocution.
• Do not insert the power cord of AC adapter into a
power outlet where the connection remains loose
despite inserting the prongs all the way into the
outlet. Heat may be generated which could lead to
fire. Consult with the retailer or an electrician
regarding replacement of the power outlet.
Store the AC adapter out of the reach of
children and infants.
The AC adapter cord may accidentally wind around the
neck and it may cause suffocation.
X-SMC1_SYXZT8_En.book 3 ページ 2011年6月15日 水曜日 午後4時44分
Page: 3
4
En
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you have
finished reading the instructions, put them in a safe place for future reference.
Contents
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Loading the batteries in the remote control. . . . . . . . . . 5
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . .5
02 Connections
Connecting using a video cable . . . . . . . . . . . . . . . . . . . 6
Connecting using an HDMI cable . . . . . . . . . . . . . . . . . 6
Connecting to a TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting to an AV receiver or amplifier. . . . . . . . . . . . .7
Audio signals that can be output from this unit's HDMI
OUT terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting the FM antenna . . . . . . . . . . . . . . . . . . . . . . 7
Connecting optional Bluetooth® adapter (optional). . . 7
Connecting USB storage devices . . . . . . . . . . . . . . . . . . 8
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
03 Part names and functions
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Top panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
04 iPod/iPhone playback
Confirming what iPod/iPhone models are
supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting your iPod/iPhone . . . . . . . . . . . . . . . . . . . . 14
Connecting your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Playing your iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . 15
05 Disc playback
Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Eject a disc from this unit . . . . . . . . . . . . . . . . . . . . . . . . .16
Example of display on the front panel display . . . . . . . 16
Playing in the desired order (Programmed Play) . . . . 17
06 Bluetooth® Audio playback (optional)
Music playback using Bluetooth wireless
technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . .18
Connecting optional Bluetooth® adapter . . . . . . . . . . 18
Setting the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pairing Bluetooth® adapter and Bluetooth wireless
technology device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Listening to Music Contents of Bluetooth wireless
technology device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
AIR JAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
07 USB playback
Playing files stored on USB storage devices . . . . . . . . 21
Playing in the desired order (Programmed Play) . . . . 21
08 Using the tuner
Connect the FM antenna . . . . . . . . . . . . . . . . . . . . . . . . 22
Listening to the FM radio broadcasts. . . . . . . . . . . . . . 22
Saving stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Listening to station presets . . . . . . . . . . . . . . . . . . . . . . 22
09 Other connections
Connecting auxiliary components . . . . . . . . . . . . . . . . 23
10 Changing the settings
Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the clock display. . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the time format. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the volume limit . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Settings for DVD/CD and USB playback . . . . . . . . . . . 25
Audio Settings parameters. . . . . . . . . . . . . . . . . . . . . . . . 25
Video Adjust parameters . . . . . . . . . . . . . . . . . . . . . . . . . 25
Initial Settings parameters . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting the HDMI Resolution settings back to their
defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sound settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using sound retriever . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using virtual surround . . . . . . . . . . . . . . . . . . . . . . . . 27
Adjusting the bass and treble . . . . . . . . . . . . . . . . . . . . . 27
Restoring all the settings to the defaults . . . . . . . . . . . 27
11 Using the timer
Setting the clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . 28
Turning the wake-up timer on/off. . . . . . . . . . . . . . . . . . . 28
Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . 28
12 Playable discs and files on discs or USB
storage devices
Playable discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Playable files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
13 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Language Code Table and Country/Area Code
Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Setting the TV system . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
About iPod/iPhone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
X-SMC1_SYXZT8_EnTOC.fm 4 ページ 2011年6月15日 水曜日 午後7時15分
Page: 4
Before you start 01
5
En
English
Français
Español
Chapter 1:
Before you start
What’s in the box
Please confirm that the following accessories are in the box
when you open it.
• Remote Control
• Power cord
• AC adapter
• Video cable
• FM wire antenna
• AAA batteries (R03) x 2
• Operating instructions (this document)
Loading the batteries in the remote
control
1 Open the rear lid and load the batteries as
illustrated below.
2 Close the rear lid.
The batteries included with the unit have been provided to
allow you check product operation and may not last long. We
recommend using alkaline batteries that have a longer life.
Caution
• When inserting the batteries, make sure not to damage
the springs on the battery’s  terminals.
• Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
• When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks ( and ).
• Do not heat batteries, disassemble them, or throw them
into flames or water.
• Batteries may have different voltages, even if they are the
same size and shape. Do not use different types of
batteries together.
• To prevent leakage of battery fluid, remove the batteries
if you do not plan to use the remote control for a long
period of time (1 month or more). If the fluid should leak,
wipe it carefully off the inside of the case, then insert
new batteries. If a battery should leak and the fluid
should get on your skin, flush it off with large quantities
of water.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
• WARNING
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Using the remote control
The remote has a range of about 7 m at an angle of about 30º
from the remote sensor.
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote.
30°
7 m
30°
X-SMC1_SYXZT8_En.book 5 ページ 2011年6月15日 水曜日 午後4時44分
Page: 5
Connections
02
6
En
Chapter 2:
Connections
• Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
• Connect the power cord after all the connections
between devices have been completed.
Connecting using a video cable
• When an iPod/iPhone is connected to this unit, the TV
output setting of iPod/iPhone is automatically set to
‘ON’.1
• Do not connect the unit through a VCR. Video signals fed
through VCRs may be affected by copyright protection
systems and the picture will be distorted on the
television.
Connecting using an HDMI cable
By using an HDMI cable, digital signals can be transferred to
an HDMI-compatible TV on a single cable with no loss of
picture or sound quality.2 After connecting, adjust unit
resolution and HDMI color settings according to the HDMI-
compatible TV. Also refer to the operating instructions with
the HDMI-compatible TV.
HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other countries.
Connecting to a TV
• If you connect this unit to your television with the HDMI
cable, sound can not be transferred from your television
to this unit. To listen to sound, connect the rear panel
AUX IN mini-plug jack to your television.
Note
1 • Some iPod allow the TV output setting to be changed while connected.
• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state.
2 • When playing a disc or USB storage device content, this unit can transfer digital signals by the HDMI OUT terminal. Use the video
cable for playing other content.
• This unit’s interface is designed based on the High-Definition Multimedia Interface specification.
• When an HDMI-compatible device is connected, the resolution is displayed on the front panel display.
• The resolution of video signals output from this unit’s HDMI OUT terminal is changed manually. Change the HDMI Resolution setting
(page 26). Settings for two units can be stored in memory.
• This unit is designed for connection to HDMI-compatible devices. It may not operate properly if connected to DVI devices.
ANTENNA
VIDEO
OUT
DC IN
19 V
FM75
Yellow
TV
Video cable
(supplied)
To video input
terminals
This unit’s rear panel
ANTENNA
AS-BT200
LABEL
SIDE
VIDEO
OUT
DC IN
19 V
FM75
HDMI
OUT
Match the direction of
the plug to the
terminal and insert
straight.
To HDMI input
terminal
HDMI cable
(commercially
available)
TV
This unit’s rear panel
X-SMC1_SYXZT8_En.book 6 ページ 2011年6月15日 水曜日 午後4時44分
Page: 6
Connections 02
7
En
English
Français
Español
Connecting to an AV receiver or amplifier
Audio signals that can be output from this
unit's HDMI OUT terminal
• 44.1 kHz to 96 kHz, 16-bit/ 20-bit/ 24-bit 2-channel linear
PCM audio (including 2-channel downmixing)
• Dolby Digital 5.1-channel audio
• DTS 5.1-channel audio
• MPEG audio
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Connecting the FM antenna
Connect the FM antenna plug onto the center pin of the FM
antenna socket.1
Connecting optional Bluetooth® adapter
(optional)
Connect the Bluetooth® adapter (Pioneer Model No.
AS-BT200) to AS-BT200 terminal on the rear panel.
• Open the AS-BT200 terminal’s cover and connect the
Bluetooth® adapter with the label side facing to the right,
then close the cover.
ANTENNA
AS-BT200
LABEL
SIDE
VIDEO
OUT
DC IN
19 V
FM75
HDMI
OUT
Match the direction of
the plug to the
terminal and insert
straight.
To HDMI input
terminal
HDMI cable
(commercially
available)
TV
This unit’s rear panel
To HDMI input
terminal
From HDMI
output terminal
AV receiver or
amplifier
HDMI cable
(commercially
available)
Note
1 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit.
ANTENNA
VIDEO
OUT
DC IN
19 V
FM75
FM wire antenna (supplied)
This unit’s rear panel
Bluetooth® adapter
(commercially available)
This unit’s
rear panel
Cover
X-SMC1_SYXZT8_En.book 7 ページ 2011年6月15日 水曜日 午後4時44分
Page: 7
Connections
02
8
En
Connecting USB storage devices
Plugging in
Important
• Before making or changing the connections, switch off
the power and disconnect the power cord from the AC
outlet.
After you’ve finished making all connections, plug the unit
into an AC outlet.
1 Plug the supplied AC adapter into the DC IN
socket on the back of the unit.
2 Plug the supplied power cord into the AC
adapter then plug the other end into an AC
outlet.
USB storage device
(commercially available)
This unit’s front panel
ANTENNA
VIDEO
OUT
DC IN
19 V
FM75
To AC outlet
AC adapter
(supplied)
This unit’s rear panel
Power cord
X-SMC1_SYXZT8_En.book 8 ページ 2011年6月15日 水曜日 午後4時44分
Page: 8
Part names and functions 03
9
En
English
Français
Español
Chapter 3:
Part names and functions
Remote control
1 STANDBY/ON
Press to turn the power on and off.
2 Number buttons (0 to 9)
Use these to specify and play the folder, track or file you
want to view/listen to. Also use them to select the station
preset when using the tuner, etc.
AUDIO*
For discs or files including multiple audio streams/
channels, the audio stream/ channel can be switched
during playback. For files stored in iPod/iPhone, this
button is not available.
SUBTITLE*
On DVD-Video or DivX discs containing subtitles in
multiple languages, the subtitle can be switched during
playback.
ANGLE*
On DVD-Video discs containing multiple angles, the
angle can be switched during playback.
3 SET UP
Use this to change initial settings of the unit. (page 24)
4 MENU
• Press to display the menu screen or Disc Navigator.
• Select and play the title, chapter, track or file from the
Disc Navigator.
• For iPod/iPhone, this button is not available.
Ex.: DVD-Video Disc Navigator
STANDBY/ON
4
5
12
13
1
2
6
15
3
7
8
9
24
25
26
27
28
01
04
02
05
03
06
Disc Navigator:Title
01- 49: ––
X-SMC1_SYXZT8_En.book 9 ページ 2011年6月15日 水曜日 午後4時44分
Page: 9
Part names and functions
03
10
En
5 ///
Use these to select items, change settings and move the
cursor.
ENTER
Use this to implement the selected item or enter a
setting that you have changed.
PRESET +/–
Use these to select station presets.
TUNE +/–
Change the frequency one step at a time. To search for
stations automatically, press and hold for about a few
second.
6 SOUND
Turns Virtual Surround and Sound Retriever on and off
(page 27). Also use to adjust the Bass and Treble.
7 FUNCTION /
Use to change the input source. The source changes as
below.
iPod  BT AUDIO1  AIR JAM1 DVD/CD USB 
FM  AUX  Return to the beginning (Undisplayed)
8  PLAY
Press to start playback.
9 //
• Press during playback to fast-reverse.
• Press in the pause mode to move backward frame-by-
frame. (DVD-Video or DVD VR discs only)
• Press and hold in the pause mode for slow play in the
reverse direction. (DVD-Video or DVD VR discs only)
10  STOP
Press to stop playback.
11  PREV
Press to return to the beginning of the currently playing track
or file. Press twice to move back to the beginning of the
previous track or file.
12 SHIFT
Press to access the ‘boxed’ commands (above the buttons)
on the remote. These buttons are marked with an asterisk (*)
in this section.
13 HOME MENU
When selecting a DVD or USB storage device input, press to
display/ hide the HOME MENU. When selecting another
input, this button is not available.
• Audio Settings (page 25)
• Video Adjust (page 25)
• Play Mode
The Play Mode function may not work for some discs or
files. For files stored on iPod/iPhone, this function is not
available.
A-B Repeat
The specified section within a single title or track is
played repeatedly.
Repeat
Plays titles, chapters, tracks or files repeatedly.
Random
Plays titles, chapters or tracks in random order.
Program (page 17)
Plays titles, chapters, tracks or files in the order in which
you program them.
Search Mode
Plays the specified number or time within the title,
chapter, track or file.
The Play Mode function may not work for some discs or
files. For files stored in iPod/iPhone, this function is not
available.
• Disc Navigator (MENU on page 9)
• Initial Settings (page 25)
14 DISP OFF
Press to turn the front panel display off when you do not need
it.
Note
1 Optionally available. To use BT AUDIO and AIR JAM function, you need to connect the commercially available Bluetooth® adapter:
AS-BT200 to the unit. See page 18 for details.
Audio Settings
Play Mode Disc Navigator
Initial Settings
Video Adjust
HOME MENU
DVD
A-B Repeat
Repeat
Random
Program
Search Mode
A(Start Point)
B(End Point)
Off
Play Mode
X-SMC1_SYXZT8_En.book 10 ページ 2011年6月15日 水曜日 午後4時44分
Page: 10
Part names and functions 03
11
En
English
Français
Español
15 SLEEP
Use to put the unit in the sleep mode and select the amount
of time before sleep (page 28).
16
Use to turn on and off the timer.
17 CLEAR
Press to clear the selected item.
Use this for example if you input the wrong number.
18 RETURN
Press to return to the previous screen. Also, use to cancel the
clock setting or the sound setting.
19 MUTE
Press to temporarily silence the sound.
20 SHUFFLE
Perform shuffle play of tracks on the selected iPod/iPhone or
DVD/CD.
21 VOLUME +/–
Use to set the listening volume. (Default setting: 10)
22 REPEAT
Perform repeat play of tracks on the selected iPod/iPhone or
DVD/CD.
23 / /
• Press during playback to fast-forward.
• Press in the pause mode to move forward frame-by-
frame. (DVD-Video, DVD VR, Video CD or DivX discs only)
• Press and hold in the pause mode for slow play in the
forward direction. (DVD-Video, DVD VR, Video CD or
DivX discs only)
24  PAUSE
Press to stop playback temporarily. Press again to resume.
25 ZOOM
Zooming on the image. For images stored in iPod/iPhone, this
button is not available.
26  NEXT
Press during playback to skip ahead to the beginning of the
next track or file.
27 DISPLAY
The elapsed time, amount remaining, etc., are displayed.
(When playing files stored in iPod/iPhone or playing in FM or
AUX mode, they are not displayed.)
28 TOP MENU
Press to display the top menu of the DVD-Video.
X-SMC1_SYXZT8_En.book 11 ページ 2011年6月15日 水曜日 午後4時44分
Page: 11
Part names and functions
03
12
En
Front panel
1 POWER ON
When the power is on, this indicator lights.
BT AUDIO1
When BT AUDIO is selected as the input source, this
indicator lights.
AIR JAM1
When AIR JAM is selected as the input source, this
indicator lights
TIMER
When the wake-up timer is set to ON, this indicator
lights.
TUNE
When the tuner receives FM broadcasts, this indicator
lights.
HDMI
When this unit is recognized by another HDMI
compatible component, this indicator lights.
2 Front panel display
3 Speaker units
4 USB terminal
5 AUX IN
Use to connect auxiliary components.
6 PHONES
Use to connect headphones.
7 iPod/iPhone connector ports
3
3
2
4 5 6 7
7
1
Note
1 Optionally available. To use BT AUDIO and AIR JAM function, you need to connect the commercially available Bluetooth® adapter:
AS-BT200 to the unit. See page 18 for details.
X-SMC1_SYXZT8_En.book 12 ページ 2011年6月15日 水曜日 午後4時44分
Page: 12
Part names and functions 03
13
En
English
Français
Español
Top panel
1 Disc slot
2  EJECT
Eject the disc.
3  STANDBY/ON
Press to turn the power on and off.
4 FUNCTION
Use to change the input source. The source changes as
below.
iPod  BT AUDIO1  AIR JAM1  DVD/CD  USB  FM
 AUX  Return to the beginning (Undisplayed)
5 BT AUDIO1
Switches the input source to Bluetooth®
Audio.
6 AIR JAM1
Switches the input source to AIR JAM.
7 
Press to start playback. During playback, pause/unpause
playback.
8 
Press to stop playback.
9 VOLUME –/+
Use to set the listening volume. (Default setting: 10)
3 6 7 8 9
7
2
1
4 5
Note
1 Optionally available. To use BT AUDIO and AIR JAM function, you need to connect the commercially available Bluetooth® adapter:
AS-BT200 to the unit. See page 18 for details.
X-SMC1_SYXZT8_En.book 13 ページ 2011年6月15日 水曜日 午後4時44分
Page: 13
iPod/iPhone playback
04
14
En
Chapter 4:
iPod/iPhone playback
Merely by connecting your iPod/iPhone to this unit, you can
enjoy high-quality sound from your iPod/iPhone. This unit
can also be connected to a television set, letting you view
videos and images from your iPod/iPhone. When connecting
to a television set, use the included video cable. This unit can
not transfer music, movies and images from an iPod/iPhone
via the HDMI OUT terminal.
Playback setting for iPod/iPhone music and images can be
performed from this unit or the iPod/iPhone itself. This unit
cannot be used to record CD, tuner or other content on an
iPod/iPhone.
Confirming what iPod/iPhone models are
supported
The iPod/iPhone playable on this unit are shown below.1
Tip
• This system has been developed and tested for the
software version of iPod/iPhone indicated on the website
of Pioneer (http://pioneer.jp/homeav/support/ios/eu/).
• Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone may result in
incompatibility with this system.
Connecting your iPod/iPhone
Caution
• When connecting iPod/iPhone devices, always use the
dock adapter provided with iPod/iPhone devices, or a
commercially available adapter designed to support
iPod/iPhone. The iPod/iPhone cannot be connected
without a dock adapter; attempting to connect an iPod/
iPhone without it will cause damage or malfunction.
• An iPod/iPhone universal dock adapter is not supplied
with this unit.
1 Open the iPod/iPhone connector port.2
2 Attach the dock adapter to iPod/iPhone
connector port.
When attaching the dock adapter, be sure to orient the front-
back directions of the dock adapter correctly. To attach, first
place the protruding tabs on the front side of the adapter into
the depressions on the iPod/iPhone connector port and press
into position. When attaching the adapter, be careful not to
strike the connectors.
iPod/iPhone Audio Video
iPod nano 1/2G  —
iPod nano 3/4/5/6G  *
* The iPod nano 6G cannot play back video, but can play slide
shows only.
iPod classic  
iPod touch 1/2/3/4G  
iPhone  
iPhone 3G  
iPhone 3GS  
iPhone 4  
Note
1 • Pioneer does not guarantee that this unit plays iPod/iPhone models other than the ones specified.
• Some functions may be restricted depending on the model or software version.
• iPod/iPhone is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.
• Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizer off before
connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience or loss of
recorded material resulting from iPod/iPhone failure.
• For detailed instructions on using the iPod/iPhone, please refer to the manual supplied with the iPod/iPhone.
2 When opening or closing the iPod/iPhone connector port, support the top of the unit with your hand to prevent it from moving
Push
X-SMC1_SYXZT8_En.book 14 ページ 2011年6月15日 水曜日 午後4時44分
Page: 14
iPod/iPhone playback 04
15
En
English
Français
Español
3 Connect your iPod/iPhone.
• When your iPod/iPhone is not connected to the unit,
close the iPod/iPhone connector port firmly.
Connecting your TV1
To watch iPod/iPhone images on a television, connect it using
the included video cable. For details, see Connecting using a
video cable on page 6.
• When an iPod/iPhone is connected to the unit, the TV
output setting of the iPod/iPhone is automatically set to
ON.2
Caution
• Before making or changing the connections, switch off
the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
Playing your iPod/iPhone
Caution
• When your iPod/iPhone is connected to this unit and
you wish to operate the iPod/iPhone directly, be sure to
steady the iPod/iPhone with the other hand to prevent
malfunctions due to faulty contacts.
1 Connect your iPod/iPhone.
• If an iPod/iPhone is connected when this unit is on,
playback of the iPod/iPhone will not begin.
2 Press FUNCTION / to select iPod as the
input source.
is shown on the front panel display.
3 Press  PLAY.
• The available iPod/iPhone’s playback control by this unit
is , , , , , , .
• In the following case, operate your iPod/iPhone directly3
:
- Searching a file by artist name or genre.
- Playing in the repeat or shuffle mode.
- Watching images stored in iPod/iPhone on your
television.
Important
If this unit can not play the iPod/iPhone when Err is displayed,
perform the following troubleshooting checks:
• Check whether the iPod/iPhone is supported by this unit.
• Reconnect the iPod/iPhone to the unit. If this doesn’t
seem to work, try resetting your iPod/iPhone.
If the iPod/iPhone cannot be operated, check the following
items:
• Is the iPod/iPhone connected correctly? Reconnect the
iPod/iPhone to the unit.
• Is the iPod/iPhone experiencing a hangup? Try resetting
the iPod/iPhone, and reconnect it to the unit.
Tip
• iPod/iPhone recharging occurs whenever an iPod/
iPhone is connected to this unit. (This function is
supported in standby mode as well.)
• When the unit is turned on while another function is
selected, playback will not automatically begin even if an
iPod/iPhone is connected.
• If the unit is set to standby when an iPod/iPhone is
connected, the iPod/iPhone’s power will be turned off
automatically.
Note
1 For detailed instructions on using the iPod/iPhone, please refer to the manual supplied with the iPod/iPhone.
2 • Some iPods allow the TV output setting to be changed while connected.
• When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state.
MENU



3
2
Push
3 For detailed instructions on using the iPod/iPhone, please refer to the manual supplied with the iPod/iPhone.
X-SMC1_SYXZT8_En.book 15 ページ 2011年6月15日 水曜日 午後4時44分
Page: 15
Disc playback
05
16
En
Chapter 5:
Disc playback
Playing discs or files
1 Press STANDBY/ON to turn the power on.
The selected input is displayed on the front panel display.
• When playing a DVD-Video or DivX discs, turn the TV on
and switch TV input before starting.
• You can change the screen display language of the unit
(OSD Language on page 26).
2 Press FUNCTION / to select DVD/CD as
the input source.
Please wait until the indicator changes from flashing
‘ ’ to ‘ ’.
When a disc has been slotted in the disc slot already, press
 EJECT to eject the disc.
3 Slot a disc.
Playback starts automatically.
• By using the number buttons (0 to 9), you can specify
and play the title, chapter, track or file you want to view/
listen to.
• Hold the disc as shown in the illustration, insert it in the
center of the disc slot, and press in gently from above.
• The disc will then be automatically drawn into the slot.
• If the disc does not load smoothly, do not attempt to
force it. Remove it from the slot and try inserting it again.
Attempting to force a disc causes damage or
malfunction.
• Do not touch the recording surface of the disc, since the
disc may not play properly if it has fingerprints or other
soiling.
• 8 cm discs cannot be played. Also do not attempt to use
adapters for 8 cm CD to play such discs, since
malfunction may result.
Eject a disc from this unit
• Press  EJECT on the top panel.
Tip
• When no operation has done in DVD/CD mode for more
than 30 minutes, the power will automatically turn off.
Example of display on the front panel
display
When the power is turned on (On)
When the power is turned off (OFF)
When the disc is being loaded (LOAd)
When the title menu or menu is displayed (titLE)
When the GUI is displayed or operated (GUI)
When the disc is stopped (StOP)
When no disc is loaded
Slot a disc with
the label side
facing front.
X-SMC1_SYXZT8_En.book 16 ページ 2011年6月15日 水曜日 午後4時44分
Page: 16
Disc playback 05
17
En
English
Français
Español
Playing in the desired order
(Programmed Play)
1 Press HOME MENU.
The HOME MENU is displayed.
2 Use / to select Play Mode, then press
ENTER.
The Play Mode screen is displayed.
3 Use / to select Program, then press
ENTER or .
4 Use / to select Create/Edit, then press
ENTER.
The Create/Edit screen differs according to the disc or file.
5 Use /// to select the title, chapter,
track or file, then press ENTER.
• To add to a program, first select the place in the program
(the program step), next select the title, chapter or track,
then press ENTER (files are added at the end of
program).
• Press RETURN to return to the previous screen. If you
return to the previous screen when inputting it, the
settings you have programmed are cleared.
• To delete a step, highlight it and press CLEAR.
6 Press PLAY to start playback.
• To play a program that has already been set, select
Playback Start from the program screen, then press
ENTER.
• To resume normal playback, select Playback Stop from
the program screen, then press ENTER. The program
remains in memory.
• To cancel the entire program, select Program Delete
from the program screen, then press ENTER.
• Programs can be played repeatedly. Select Program
Repeat from Repeat on the Play Mode screen during
programmed playback.
• Programs cannot be played in random order (random
play is not possible during programmed play).
Program Step
01.
02.
03.
04.
05.
06.
07.
08.
Title 1-01
Title 01
Program
Chapter 1-015
Chapter 001
Chapter 002
Chapter 003
Chapter 004
Chapter 005
Chapter 006
Chapter 007
Chapter 008
X-SMC1_SYXZT8_En.book 17 ページ 2011年6月15日 水曜日 午後4時44分
Page: 17
Bluetooth® Audio playback (optional)
06
18
En
Chapter 6:
Bluetooth® Audio playback (optional)
Music playback using Bluetooth wireless
technology
When the Bluetooth® adapter (Pioneer Model No. AS-BT200)
is connected to this unit, a product equipped with Bluetooth
wireless technology (portable cell phone, digital music player,
etc.) can be used to listen to music wirelessly.1
Also, by using
a commercially available transmitter supporting Bluetooth
wireless technology, you can listen to music on a device not
equipped with Bluetooth wireless technology. The AS-BT200
model supports SCMS-T contents protection, so music can
also be enjoyed on devices equipped with SCMS-T type
Bluetooth wireless technology.
Remote control operation
The remote control supplied with this unit allows you to play
and stop media, and perform other operations.2
Connecting optional Bluetooth® adapter
1 Connect the Bluetooth® adapter to the unit
when the unit is in standby mode.
• Remove the AS-BT200 terminal’s cover and connect the
Bluetooth® adapter with the label side facing to the right,
then close the cover.
Remote control operation
This unit
Bluetooth®
adapter
Device not equipped with Bluetooth
wireless technology:
Digital music player
+
Bluetooth® audio transmitter
(commercially available)
Bluetooth wireless technology
enabled device:
Digital music player
Bluetooth wireless technology
enabled device:
Cell phone
Note
1 • The Bluetooth wireless technology enabled device must support A2DP profiles.
• Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology enabled devices.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER
CORPORATION is under license. Other trademarks and trade names are those of their respective owners.
2 • The Bluetooth wireless technology enabled device must support AVRCP profiles.
• Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.
Bluetooth® adapter
(commercially
available)
This unit’s
rear panel
Cover
X-SMC1_SYXZT8_En.book 18 ページ 2011年6月15日 水曜日 午後4時44分
Page: 18
Bluetooth®
Audio playback (optional) 06
19
En
English
Français
Español
2 Press STANDBY/ON to turn the power on.
3 Press FUNCTION / or BT AUDIO on the
front panel of the unit to select BT AUDIO as the
input source.1
The BT AUDIO indicator lights and is shown on the
front panel display.
Setting the PIN code
Set this unit’s PIN code to the same setting as that for the
Bluetooth wireless technology device used. Supported PIN
code setting values include 0000, 1234 or 8888.
• Default setting: 0000
1 Press SET UP continuously to select
.
• Each time SET UP is pressed the item on the front panel
display changes accordingly.
2 Press ENTER continuously to select the PIN
code .
• Each time / is pressed the item on the front panel
display changes accordingly.
• You can select the PIN number from 0000/1234/8888.
3 Press ENTER.
The PIN code is stored.
4 Press SET UP.
The setting is completed.
Pairing Bluetooth® adapter and
Bluetooth wireless technology device
“Pairing” must be done before you start playback of Bluetooth
wireless technology content using Bluetooth® adapter. Make
sure to pair devices the first time you operate the system or
any time pairing data is cleared. “Pairing” is the step
necessary to register Bluetooth wireless technology device to
enable Bluetooth communications.2 For more details, see
also the operating instructions of your Bluetooth wireless
technology device.
1 Press FUNCTION / or BT AUDIO on the
front panel of the unit to select BT AUDIO as the
input source.
The BT AUDIO indicator lights .
• When Bluetooth® adapter AS-BT200 is connected,
is shown on the front panel display for 2
seconds, then is shown.
• When no Bluetooth® adapter is connected, is
shown on the front panel display for 2 seconds, then
is shown.
2 Turn on the Bluetooth wireless technology
device that you want to pair, place it near the
system and set it into pairing mode.
Pairing starts.
3 Check to see that the Bluetooth® adapter is
detected by the Bluetooth wireless technology
device.
• If the Bluetooth wireless technology device cannot be
connected to the unit, perform the connection operation
from the Bluetooth wireless technology device.
Note
1 When the Bluetooth® adapter is not connected and BT AUDIO is selected as the input source, the error message noAdP. will be shown
on the front panel display.
2 • Pairing is required when you first use Bluetooth wireless technology device and Bluetooth® adapter.
• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology device.
X-SMC1_SYXZT8_En.book 19 ページ 2011年6月15日 水曜日 午後4時44分
Page: 19
Bluetooth® Audio playback (optional)
06
20
En
Listening to Music Contents of Bluetooth
wireless technology device
1 Press FUNCTION / or BT AUDIO on the
front panel of the unit to select BT AUDIO as the
input source.
The BT AUDIO indicator lights and is shown on the
front panel display.
2 Make connection between the Bluetooth
wireless technology device and the unit.
• See Pairing Bluetooth® adapter and Bluetooth wireless
technology device above.
3 Press  PLAY to start playback.
The following operations are now possible for Bluetooth
wireless technology devices, using the remote control.1
Tip
• When no Bluetooth wireless technology device is
connected and no operation has been done for 30
minutes or more, the power will automatically turn off.
AIR JAM
Air Jam – a Pioneer-exclusive application and available for
free.
Air Jam lets you connect multi compatible devices to this unit
using Bluetooth wireless technology. With it, you can make a
group playlist directly on a supported device to play in your
home theater through the unit. You and your friends can add
songs from your devices to the playlist.
1 Press FUNCTION / or AIR JAM on the
front panel of the unit to select AIR JAM as the
input source.
The AIR JAM indicator lights.
• When Bluetooth® adapter AS-BT200 is connected,
is shown on the front panel display for 2
seconds, then is shown.
• When no Bluetooth® adapter is connected, is
shown on the front panel display for 2 seconds, then
is shown.
For more details on using Air Jam, access our website.
http://pioneer.jp/product/soft/iapp_airjam/en.html
Button What it does
 PLAY Starts normal playback.
 PAUSE Pauses playback.
 STOP Stops playback.
 PREV Press to skip to the start of the current file, then
previous files.
 Press and hold to start fast reverse scanning.*
* This function may work differently depending on the connected
device.
 NEXT Press to skip to the next file.
 Press and hold to start fast forward scanning.*
Note
1 • The Bluetooth wireless technology enabled device must support AVRCP profile.
• The operation of some Bluetooth wireless technology devices may differ from what is shown the above table.
X-SMC1_SYXZT8_En.book 20 ページ 2011年6月15日 水曜日 午後4時44分
Page: 20
USB playback 07
21
En
English
Français
Español
Chapter 7:
USB playback
Playing files stored on USB storage
devices
• This unit may not recognize a USB storage device, play
files or supply power to a USB storage device. For
details, see When a USB storage device is connected on
page 33.
• Pioneer does not guarantee that any file recorded on a
USB storage device will play or that power will be
supplied to a USB storage device. Also note that Pioneer
will accept no responsibility whatsoever for loss of files
on USB storage devices caused by connection to this
unit.
1 Press STANDBY/ON to turn the power on.
The selected input is displayed on the front panel display.
2 Press FUNCTION / to select USB as the
input source.
‘ ’ is shown on the front panel display.
3 Connect a USB storage device.
The Disc Navigator appears automatically.
4 Use /// to select the file, then press
ENTER.
Playback starts.
• If you press  PLAY, this unit will automatically play files
stored on a USB storage device.
• Turn the power off before removing the USB storage
device.
Tip
• When a USB storage device is not playing and the unit
has not been operated for 30 minutes or more, the power
will automatically turn off.
Playing in the desired order
(Programmed Play)
This unit can play repeatedly files stored in the USB storage
device. For details, see Playing in the desired order
(Programmed Play) on page 17.
X-SMC1_SYXZT8_En.book 21 ページ 2011年6月15日 水曜日 午後4時44分
Page: 21
Using the tuner
08
22
En
Chapter 8:
Using the tuner
• This unit can not transfer FM radio from the HDMI OUT
terminal.
Connect the FM antenna
Connect the FM antenna plug onto the center pin of the FM
antenna socket.1
For details, see Connecting the FM antenna
on page 7.
Listening to the FM radio broadcasts
The tuner can receive FM broadcasts, and can save your
favorite stations.
1 Press FUNCTION / to select FM as the
input source.
The tuned frequency will be displayed on the front panel
display (e.g., ‘ ’).
2 Tune into a station.
When the tuner receives FM broadcasts, the TUNE indicator
lights.
There are two ways to do this:
Automatic tuning - To search for stations, press and
hold TUNE +/– for about a few second. This unit will start
searching for the next station, stopping when it has
found one. Repeat to search for other stations.
Manual tuning - To change the frequency one step at a
time, press TUNE +/–.
Saving stations
You can save up to 9 station presets so that you always have
easy access to your favorite stations without having to tune in
manually each time.2
• Manually saving station presets
1 Press FUNCTION / to select FM as the
input source.
The tuned frequency will be displayed on the front panel
display.
2 Tune into a station.
3 Press and hold a number button (1 to 9) for
three seconds.
The tuned frequency is preset to the selected number button.
The previous station preset is overwritten.
• Automatically saving station presets
1 Press and hold PRESET + for three seconds.
Auto tuning starts.
• The tuned frequencies will be preset to the buttons in
numerical order.
• Auto tuning stops automatically after setting up the FM
band, or after the limit of 9 presets has been reached.
Listening to station presets
1 Press FUNCTION / to select FM as the
input source.
The tuned frequency will be displayed on the front panel
display.
2 Press the number button (1 to 9) that stores
the FM radio station.
Tip
• Press PRESET +/– repeatedly to selected the station
preset in numerical order.
Note
1 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit.
2 When a new broadcast frequency is stored in a station containing a previously stored frequency, the previous frequency will be overwrit-
ten with the new one.
08_tuner_SMC1.fm 22 ページ 2011年6月15日 水曜日 午後5時49分
Page: 22
Other connections 09
23
En
English
Français
Español
Chapter 9:
Other connections
• Before making or changing the connections, switch off
the power and disconnect the power cord from the AC
outlet.
• If the AUX IN mini-plug jack is connected to auxiliary
phones jack, the volume of the unit will be adjusted by
the volume on the playback component. If the sound is
distorted after you lower the volume of the unit, try
lowering the volume on the auxiliary playback
component.
• This unit can not transfer the external input’s sound from
the HDMI OUT terminal.
Connecting auxiliary components
Connect the rear panel AUX IN mini-plug jack to your
auxiliary playback component.
• This method can be used to play music on this unit from
iPods/iPhones that do not support use of an iPod Dock.
• Press FUNCTION / to select AUX as the
input source.
When AUX is selected, ‘ ’ is displayed on the front
panel display.
Tip
• When no auxiliary component is connected to the AUX
IN mini-plug jack and the unit has not been operated for
30 minutes or more, the power will automatically turn
off.
Digital audio
player, etc.
Stereo mini-plug cable
(commercially available)
This unit’s front panel
X-SMC1_SYXZT8_En.book 23 ページ 2011年6月15日 水曜日 午後4時44分
Page: 23
Changing the settings
10
24
En
Chapter 10:
Changing the settings
Initial settings
Setting the clock display
Activate and deactivate the clock display.
1 Press SET UP continuously to select
.
• Each time SET UP is pressed the item on the front panel
display changes accordingly.
2 Press ENTER to select or .
• Each time ENTER is pressed the item on the front panel
display changes accordingly.
– The clock display is activated.
– The clock display is deactivated.
3 Press SET UP.
The setting is completed.
Setting the time format
1 Press SET UP continuously to select
.
• Each time SET UP is pressed the item on the front panel
display changes accordingly.
2 Press ENTER to select or .
• Each time ENTER is pressed the item on the front panel
display changes accordingly.
– 24-hour (24H) clock is displayed.
– 12-hour (12H) clock is displayed.
3 Press SET UP.
The setting is completed.
Setting the volume limit
You can set the volume level limit of this unit.
1 Press SET UP continuously to select
.
• Each time SET UP is pressed the item on the front panel
display changes accordingly.
2 Press ENTER to select or .
• Each time ENTER is pressed the item on the front panel
display changes accordingly.
– You can adjust the volume level up to the
maximum volume level of this unit.
– You can adjust the volume levels between
0 and 30.
3 Press SET UP.
The setting is completed.
Setting the PIN code
See Setting the PIN code on page 19.
X-SMC1_SYXZT8_En.book 24 ページ 2011年6月15日 水曜日 午後4時44分
Page: 24
Changing the settings 10
25
En
English
Français
Español
Settings for DVD/CD and USB playback
1 Press HOME MENU.
HOME MENU screen appears.
2 Use ///to select the item, then press ENTER.
3 Use ///to change the setting, then press ENTER.
Closing the HOME MENU screen.
Press HOME MENU.
The factory default settings are indicated in italic.
Important
• The following settings are available for a disc or USB storage device content. They are not available for iPod/iPhone, tuner,
external input (AUX).
• In the USB mode, you can only change the Play Mode and Audio Settings on the HOME MENU screen.
Audio Settings parameters
Video Adjust parameters
Brightness, Contrast, Gamma, Hue and Chroma Level are set to 0 upon purchase.
Initial Settings parameters
• Use these settings to make detailed unit settings.
• Initial Settings cannot be selected during playback. Stop the disc first.
Settings What it does
Equalizer
(Off /Rock/Pop/Live/Dance/
Techno/Classic/Soft)
Select according to the genre of music to be listened to.
Audio DRC
(High/Medium/Low/Off)
• This makes loud sounds weaker and weak sounds louder. Change the setting for example when
watching movies late at night.
• This setting only affects Dolby Digital sound.
• The effect depends on the volume of the connected TV, AV receiver or amplifier, speakers, etc. Try
different settings, and choose the one providing the strongest effect.
Dialog
(High/Medium/Low/Off)
Change this setting if the dialog sound is too low and hard to hear. This setting only affects multichannel
sound.
Settings What it does
Sharpness
(Fine/Standard /Soft)
Adjusts the picture’s sharpness.
Brightness
(-20 to +20)
Adjusts the picture’s brightness.
Contrast
(-16 to +16)
Adjusts the ratio of the brightness of the brightest and darkest portions of the picture.
Gamma
(-3 to +3)
Adjusts the look of the dark portions of the picture.
Hue
(green 9 to red 9)
Adjusts the balance between green and red.
Chroma Level
(-9 to +9)
Adjusts the density of the colors. This setting is effective for sources with many colors, such as cartoons.
X-SMC1_SYXZT8_En.book 25 ページ 2011年6月15日 水曜日 午後4時44分
Page: 25
Changing the settings
10
26
En
Digital Audio Out settings
Video Output settings
Language settings
• If the above setting is used to select “Other Language,” perform operations while referring to Language Code Table and
Country/Area Code Table on page 35.
Display settings
Options settings
Setting the HDMI Resolution settings back to their defaults
1 Press  STANDBY/ON to turn the power off.
2 Press  STANDBY/ON while pressing VOLUME –.
Use the buttons on this unit’s top panel. The power turns on.
Settings What it does
HDMI Out Select the audio signals to be output from the HDMI OUT terminal (LPCM (2CH)/Auto/Off ) according
to the connected HDMI-compatible device.
Settings What it does
TV Screen Change the picture display format (4:3 (Letter Box)/4:3 (Pan & Scan)/16:9 (Wide)/16:9
(Compressed)), according to the connected TV.
HDMI Resolution Change the resolution of the video signals output from the HDMI OUT terminals (720x480i/720x480p/
1280x720p/1920x1080i/1920x1080p). If the image does not appear correctly after changing the
setting, return the setting to “720x480p.” Refer to Setting the HDMI Resolution settings back to their
defaults on page 26.
HDMI Color Change the video signals output from the HDMI OUT terminal (Full range RGB/RGB/Component).
Settings What it does
Audio Language Change the language when listening to the sound of DVD-Video discs (English/available languages/
Other Language).
Subtitle Language Change the language of the subtitles displayed for DVD-Video discs (English/available languages/
Other Language).
DVD Menu Lang. Change the language used for the menu displays of DVD-Video discs
(w/ Subtitle Lang./available languages/Other Language).
Subtitle Display Select whether to display subtitles (On) or not (Off).
Settings What it does
OSD Language Change the language of the operation messages (Play, Stop, etc.) displayed on the TV screen (English/
available languages).
Angle Indicator Select whether to display the angle mark on the TV screen (On) or not (Off).
On Screen Display Select whether to display operation messages (Play, Stop, etc.) on the TV screen (On) or not (Off).
Settings What it does
Parental Lock Restrict DVD-Video viewing (Password/Level Change/Country Code). See Language Code Table and
Country/Area Code Table on page 35 in order to set the “Country Code.”
DivX VOD Display the registration code required for playing DivX VOD files (Activate/Deactivate).
X-SMC1_SYXZT8_En.book 26 ページ 2011年6月15日 水曜日 午後4時44分
Page: 26
Changing the settings 10
27
En
English
Français
Español
Sound settings
Using sound retriever
1 Press SOUND to select Sound Retriever.
2 Use / to select or .
The newly set value displays for 5 seconds, and then the
setting is completed.
– The selected sound effect is activated.
–The selected sound effect is deactivated.
About Sound Retriever
This function enhances sound data lost during compression
of MP3 and other file types, allowing the user to enjoy sound
quality closer to that of the original signal data.
Using virtual surround
1 Press SOUND to select Virtual Surround.
2 Use / to select or .
The newly set value displays for 5 seconds, and then the
setting is completed.
– The selected sound effect is activated.
–The selected sound effect is deactivated.
Adjusting the bass and treble
Use the bass and treble controls to adjust the overall tone.
1 Press SOUND to select Bass or Treble.
2 Use / to adjust the bass or treble.
You can adjust low and high sounds on a scale of –5 to +5
(eleven steps).
– Bass +5
– Bass -5
– Treble +5
– Treble -5
The newly set value displays for 5 seconds, and then the
setting is completed.
Restoring all the settings to the defaults
Note
• Use the steps below to restore the above settings to their
defaults.
1 Press  STANDBY/ON to turn the power
on.
2 Press  STANDBY/ON while pressing .
Use the buttons on this unit’s top panel. ‘ ’ is
displayed while the settings are being restored.
X-SMC1_SYXZT8_En.book 27 ページ 2011年6月15日 水曜日 午後4時44分
Page: 27
Using the timer
11
28
En
Chapter 11:
Using the timer
Setting the clock
• Default setting:
1 With the power turned on, press .
The current time is displayed on the front panel display.
2 Press again.
is displayed on the front panel display.
3 Press ENTER.
The hour blinks on the front panel display.
4 Use / to set the hour, then press ENTER.
The minute blinks on the front panel display.
5 Use / to set the minute, then press
ENTER.
The newly set value displays for 5 seconds, and then the
setting is completed.
Setting the wake-up timer
1 With the power turned on, press FUNCTION
/ to select an input source.
• iPod, DVD/CD, FM and AUX can be selected as the
input source.
2 Press .
The current time is displayed on the front panel display.
3 Press twice.
is displayed on the front panel display.
4 Press ENTER.
The hour blinks on the front panel display.
• While hour or minute digits are blinking, volume level
can be adjusted.
5 Use / to set the hour, then press ENTER.
The minute blinks on the front panel display.
• While hour or minute digits are blinking, volume level
can be adjusted.
6 Use / to set the minute, then press
ENTER.
Turning the wake-up timer on/off
1 With the power turned on, press .
The current time is displayed on the front panel display.
2 Press three times.
The newly set value displays for 5 seconds on the front panel.
3 Press ENTER to select or .
The newly set value displays for 5 seconds, and then the
setting is completed.
– The wake-up timer is set to on.
– The wake-up timer is set to off.
Using the wake-up timer
1 Press STANDBY/ON to turn the power off.
2 At the wake-up time, this unit will turn on
automatically and play the selected input
function.
If this unit is not operated for 60 minutes or more after
playback is started by the wake-up timer, power will
automatically turn off (standby mode).
Note
• If at the wake-up time iPod/iPhone is not connected to
this unit or a disc is not inserted, this unit will be turned
to on and not play back the track.
• Some discs may not be played automatically at the wake-
up time.
Using the sleep timer
The sleep timer switches off the unit after a specified time so
you can fall asleep without worrying about it.
• Press SLEEP repeatedly to select a switch off
time.
Choose between 5 min, 15 min, 30 min, 60 min, 90 min or OFF.
The newly set value displays for 3 seconds, and then the
setting is completed.
• If you press SLEEP while the sleep timer is set, the
remaining time will be displayed.1
Note
1 The sleep timer can be set by pressing SLEEP while the remaining time is displayed.
X-SMC1_SYXZT8_En.book 28 ページ 2011年6月15日 水曜日 午後4時44分
Page: 28
Playable discs and files on discs or USB storage devices 12
29
En
English
Français
Español
Chapter 12:
Playable discs and files on discs or USB
storage devices
Playable discs
• Only the discs that have been finalized can be
played.
• Discs recorded in packet write mode (UDF format) are
not compatible with this unit.
• 8 cm discs cannot be played. Also do not attempt to use
adapters for 8 cm CD to play such discs, since
malfunction may result.
• is a trademark of DVD Format/ Logo Licensing
Corporation.
• is a trademark of FUJIFILM Corporation.
• Corporation and product names mentioned herein are
trademarks or registered trademarks of the respective
corporations.
Note
• For detailed instructions on files that iPod/iPhone can
play, refer to the manual supplied with the iPod/iPhone.
• This unit does not support multisession discs or
multiborder recording.
• Multisession/multiborder recording is a method in
which data is recorded on a single disc in two or more
sessions/borders. A “session” or “border” is one
recording unit, consisting of a complete set of data from
lead-in to lead-out.
Discs that cannot be played
• Blu-ray discs
• HD DVDs
• AVCHD
• AVCREC
• DVD-Audio discs
• DVD-RAM discs
• SACDs
• CD-G
About region numbers
DVD player and DVD-Video discs are assigned region
numbers according to the region in which they are sold. This
player’s region number(s) is (are) as shown below.
• DVD-Video: 2
(For Russian model: 5)
Discs not including these numbers cannot be played. Discs
playable on this player are as shown below.
• DVDs: 2 (including 2) and ALL
(For Russian model: 5 (including 5) and ALL)
• Commercially available DVD-Video discs
• DVD-R/ -RW/ -R DL and DVD+R/ +RW/ +R DL discs recorded in the Video mode
DVD-R/ -RW/ -R DL discs recorded in the VR mode
Video CDs
• Commercially available audio CDs
• CD-R/ -RW/ -ROM discs containing music recorded in the CD-DA format
JPEG files recorded on DVD-R/ -RW/ -R DL discs, CD-R/ -RW/ -ROM discs or USB storage devices
DivX video files recorded on DVD-R/ -RW/ -R DL discs, CD-R/ -RW/ -ROM discs or USB storage devices
WMA files recorded on DVD-R/ -RW/ -R DL discs, CD-R/ -RW/ -ROM discs or USB storage devices
MP3 files recorded on DVD-R/ -RW/ -R DL discs, CD-R/ -RW/ -ROM discs or USB storage devices
FUJICOLOR-CD
X-SMC1_SYXZT8_En.book 29 ページ 2011年6月15日 水曜日 午後4時44分
Page: 29
Playable discs and files on discs or USB storage devices
12
30
En
Regarding copy protected CDs
This unit is designed to conform to the specifications of the
audio CD format. This unit does not support the playback or
function of discs that do not conform to these specifications.
About playing DualDiscs
A DualDisc is a new two-sided disc, one side of which
contains DVD content - video, audio, etc. - while the other side
contains non-DVD content such as digital audio material.
• The DVD side of a DualDisc can be played on this unit
(excluding any DVD-Audio content).
• The non-DVD, audio side of the disc is not compatible
with this unit.
• It is possible that when loading or ejecting a DualDisc,
the opposite side to that being played will be scratched.
Scratched discs may not be playable.
• For more detailed information on DualDisc
specifications, please refer to the disc manufacturer or
disc retailer.
Playing discs created on computers or BD/DVD
recorders
• It may not be possible to play discs recorded using a
computer due to the application settings or computer’s
environment settings. Record discs in a format playable
on this unit. For details, contact the dealer.
• It may not be possible to play discs recorded using a
computer or a BD/DVD recorder, if burn quality is not
good due to characteristics of the disc, scratches, dirt on
the disc, dirt on the recorder’s lens, etc.
Playable files
• Only discs recorded in ISO9660 Level 1, Level 2 and Joliet
can be played.
• Files protected by DRM (Digital Rights Management)
cannot be played.
• Files other than the ones below (WMV, MPEG4-AAC,
etc.) are not guaranteed to play.
Supported video file formats
DivX
• DivX is a media technology created by DivX, Inc. DivX
media files contain image data.
• DivX files may also include such advanced playback
functions as menu screens and selection of multiple
subtitle languages/ audio tracks.
• DivX Certified® to play DivX® video, including premium
content.
• DivX®, DivX Certified® and associated logos are
trademarks of DivX, Inc. and are used under license.
File extensions: .avi and .divx (these must be used for this unit
to recognize DivX video files). Note that all files with the .avi
extension are recognized as MPEG4, but not all of these are
necessarily DivX video files and therefore may not be playable
on this unit.
• Files not containing DivX video signals cannot be played,
even if they have the extension “.avi”.
Displaying external subtitle files
• The font sets listed below are available for external
subtitle files. You can see the proper font set on-screen
by setting the Subtitle Language on page 26 to match
the subtitle file.
• This unit supports the following language groups:
• Some external subtitle files may be displayed incorrectly
or not at all.
• For external subtitle files the following subtitle format
filename extensions are supported (please note that
these files are not shown within the disc navigation
menu): .srt, .sub, .ssa, .smi
• The filename of the movie file has to be repeated at the
beginning of the filename for the external subtitle file.
• The number of external subtitle files which can be
switched for the same movie file is limited to a maximum
of 10.
Supported image file formats
JPEG
Resolution: Up to 3072 x 2048 pixels
File extensions: .jpg and .JPG (must be used for this unit to
recognize JPEG files - do not use for other file types)
• This unit supports baseline JPEG.
• This unit supports Exif Ver.2.2.
• This unit does not support progressive JPEG.
Supported audio file formats
• This unit does not support VBR (Variable Bit Rate).
• This unit does not support lossless encoding.
Group 1 Afrikaans (af), Basque (eu), Catalan (ca), Danish
(da), Dutch (nl), English (en), Faroese (fo), Finnish
(fi), French (fr), German (de), Icelandic (is), Irish
(ga), Italian (it), Norwegian (no), Portuguese (pt),
Rhaeto-Romanic (rm), Scottish (gd), Spanish (es),
Swedish (sv)
Group 2 Albanian (sq), Croatian (hr), Czech (cs), Hungarian
(hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Group 3 Bulgarian (bg), Byelorussian (be), Macedonian
(mk), Russian (ru), Serbian (sr), Ukrainian (uk)
Group 4 Hebrew (iw), Yiddish (ji)
Group 5 Turkish (tr)
X-SMC1_SYXZT8_En.book 30 ページ 2011年6月15日 水曜日 午後4時44分
Page: 30
Playable discs and files on discs or USB storage devices 12
31
En
English
Français
Español
Windows MediaTM Audio (WMA)
Sampling frequencies: 32 kHz, 44.1 kHz and 48 kHz
Bit rate: Up to 192 kbps
File extensions: .wma and .WMA
• This unit supports files encoded using Windows Media
Player Ver. 7/ 7.1, Windows Media Player for Windows
XP and Windows Media Player 9 Series.
• Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United States
and/ or other countries.
• This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a
license from Microsoft Licensing, Inc.
MPEG-1 Audio Layer 3 (MP3)
Sampling frequencies: 32 kHz, 44.1 kHz and 48 kHz
Bit rate: Any (128 kbps or higher recommended)
File extensions: .mp3 (these must be used for this unit to
recognize MP3, WMA and MPEG-4 AAC files - do not use for
other file types)
X-SMC1_SYXZT8_En.book 31 ページ 2011年6月15日 水曜日 午後4時44分
Page: 31
Additional information
13
32
En
Chapter 13:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components
and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your
nearest Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the
outlet and insert again to return to normal operating conditions.
General problem
Problem Check Remedy
Settings you have made have
been cleared.
Was the power cord unplugged
forcibly while this unit’s power was
on?
Be sure to press STANDBY/ON on this unit’s front panel or press
STANDBY/ON on the remote control and wait for the POWER ON
indicator on the front panel display to turn off before unplugging
the power cord.
Difference in volume
between DVDs, CDs, MP3,
WMA, iPod/iPhone and
Tuner.
This is not a problem with this unit. The volume may sound differently depending on the input source
and recording format.
This unit cannot be operated
with the remote control.
Are you operating from far away? Operate from within a distance of Operate within 7 m (23 ft.), 30° of
the remote sensor on the front panel (page 5).
Is the remote control sensor exposed
to direct sunlight or strong artificial
light from a fluorescent bulb, etc.?
The remote control signals may not be received properly if the
remote control sensor is exposed to direct sunlight or strong
artificial light from a fluorescent bulb, etc.
Are the batteries dead? Replace the batteries (page 5).
Disc cannot be played or disc
is ejected automatically.
Is the disc scratched? Scratched discs may not play.
Is the disc dirty? Wipe the dirt off the disc (page 37).
Is the disc properly slotted? Slot a disc with the label side facing front.
Does the disc have the right region
number?
Discs with the region number “2 (including 2)” and “ALL” can be
played on this unit.
Is this unit placed in a humid
location?
There could be condensation inside. Wait a while for the
condensation to evaporate. Do not place this unit near an air-
conditioner, etc. (page 36).
Picture is stretched, or
aspect ratio cannot be
switched.
Is the aspect ratio properly set on the
connected TV?
Refer to the TV’s operating instructions and set the TV’s aspect ratio
properly.
Is TV Screen properly set? Set TV Screen properly (page 26). This setting is available for a disc
or USB storage device content. For movies and images stored in
iPod/iPhone, operate your iPod/iPhone.
13_additional_info_SMC1.fm 32 ページ 2011年6月15日 水曜日 午後8時8分
Page: 32
Additional information 13
33
En
English
Français
Español
When a USB storage device is connected
During playback, picture is
disturbed or dark.
This is not a problem with this unit. This unit supports Rovi copy protection. With some TVs, the picture
may not display properly when playing discs including copy
prevention signals. This is not a malfunction.
Are this unit and TV connected via a
video deck?
When this unit and TV are connected via a video deck, this unit’s
analog copy protect function may cause the picture being played
on the video deck not to display properly. Connect this unit and TV
directly.
Is the TV system properly set? The factory default setting is AUTO. If the picture is distorted,
switch the TV system to the one used in your country or region
(NTSC or PAL) (page 36).
Sound and image are
intermittent during disc
playback.
Sound volume may be too high. Sound and image may be unsteady if sound volume is set too high;
in this case, lower the sound volume.
Folder or file names are not
recognized.
Have you exceeded the maximum
number of folder or file names this
unit can recognize?
Up to 299 folders can be recognized on one disc. Up to 648 files can
be recognized within one folder. Depending on the folder structure,
however, this unit may not be able to recognize certain folders or
files.
Time is required to play JPEG
files.
Are you playing large files? Some time may be required to display large files.
Black bars are displayed
when playing JPEG files.
Are you playing files with different
aspect ratios?
Black bars may be displayed along the top and bottom or sides
when JPEG files with different aspect ratios are played.
The unit turns off
automatically.
If no operation has done for 30 minutes or more, the unit turns off
automatically.
Problem Check Remedy
Problem Check Remedy
USB storage device is not
recognized.
Is the USB storage device properly
connected?
Connect the device securely (all the way in).
Is the USB storage device connected
via a USB hub?
This unit does not support USB hubs. Connect the USB storage
device directly.
This unit only supports USB mass storage class devices.
This unit supports portable flash memory and digital audio
playback devices.
Only the FAT16 and FAT32 file systems are supported. Other file
systems (ex. FAT, NTFS, etc.) are not supported.
This device does not support the use of external hard disc drives.
This is not a problem with this unit. Turn the power off then back on.
Some USB storage devices may not be recognized properly.
File cannot be played. Is the file copyright-protected (by
DRM)?
Copyright-protected files cannot be played.
This is not a problem with this unit. Files stored on a computer cannot be played.
It may not be possible to play some files.
Folder or file names are not
displayed or are not properly
displayed.
Do the folder of file names contain
more than 14 characters?
The maximum number of characters displayable for the folder and
file names on the Disc Navigator is 14.
13_additional_info_SMC1.fm 33 ページ 2011年6月16日 木曜日 午前9時54分
Page: 33
Additional information
13
34
En
When connected to an HDMI-compatible
device
When an iPod/iPhone is connected
Folder or file names are not
displayed in alphabetical
order.
This is not a problem with this unit. The order of the folder and file names displayed on the Disc
Navigator depends on the order in which the folders or files were
recorded on the USB storage device.
Much time is required to
recognize the USB storage
device.
What is the USB storage devices
capacity?
Some time may be required to load the data when large capacity
USB storage devices are connected (this could take several
minutes).
Power is not supplied to the
USB storage device.
Is Err displayed on the front panel
display? No power is supplied if the
power consumption is too high.
Turn the power off then back on.
Turn the power off, then disconnect and reconnect the USB storage
device.
Press FUNCTION / to switch to the other mode, then switch
again to the USB mode. (When the input is switched back to USB,
‘ ’ is displayed on the front panel display.)
Problem Check Remedy
Problem Check Remedy
Picture is not displayed. Is the resolution properly set? Set HDMI Resolution properly for the connected device (page 26).
Restore HDMI Resolution to the default setting (720x480p)
(page 26).
Is the HDMI cable properly
connected?
Connect the cable securely (all the way in).
With some cables, 1080p video signals will not be output.
Sound is not produced or is
distorted.
Is HDMI Out properly set? Set HDMI Out to LPCM (2CH) or Auto (page 26).
Multichannel audio signals
are not output.
Is HDMI Out properly set? Set HDMI Out to Auto (page 26).
Colors are not properly
displayed on TV screen.
Is HDMI Color properly set? Change the HDMI Color setting (page 26).
Problem Remedy
Can’t operate the iPod/
iPhone by the remote control.
Make sure the iPod/iPhone is connected correctly (refer to
Connecting your iPod/iPhone on page 14).
Can’t operate the iPod/
iPhone.
Make sure the iPod/iPhone is connected correctly (refer to
Connecting your iPod/iPhone on page 14).
If the iPod/iPhone is experiencing a hangup, try resetting the iPod/
iPhone, and reconnect it to the unit.
X-SMC1_SYXZT8_En.book 34 ページ 2011年6月15日 水曜日 午後4時44分
Page: 34
Additional information 13
35
En
English
Français
Español
Language Code Table and Country/Area
Code Table
Language Code Table
Language names (codes) and input codes:
Country/Area Code Table
Country/Area name, Input codes and Country/
Area code
Japanese (ja), 1001 Frisian (fy), 0625
English (en), 0514 Irish (ga), 0701
French (fr), 0618 Scots-Gaelic (gd), 0704
German (de), 0405 Galician (gl), 0712
Italian (it), 0920 Guarani (gn), 0714
Spanish (es), 0519 Gujarati (gu), 0721
Chinese (zh), 2608 Hausa (ha), 0801
Dutch (nl), 1412 Hindi (hi), 0809
Portuguese (pt), 1620 Croatian (hr), 0818
Swedish (sv), 1922 Hungarian (hu), 0821
Russian (ru), 1821 Armenian (hy), 0825
Korean (ko), 1115 Interlingua (ia), 0901
Greek (el), 0512 Interlingue (ie), 0905
Afar (aa), 0101 Inupiak (ik), 0911
Abkhazian (ab), 0102 Indonesian (in), 0914
Afrikaans (af), 0106 Icelandic (is), 0919
Amharic (am), 0113 Hebrew (iw), 0923
Arabic (ar), 0118 Yiddish (ji), 1009
Assamese (as), 0119 Javanese (jw), 1023
Aymara (ay), 0125 Georgian (ka), 1101
Azerbaijani (az), 0126 Kazakh (kk), 1111
Bashkir (ba), 0201 Greenlandic (kl), 1112
Byelorussian (be), 0205 Cambodian (km), 1113
Bulgarian (bg), 0207 Kannada (kn), 1114
Bihari (bh), 0208 Kashmiri (ks), 1119
Bislama (bi), 0209 Kurdish (ku), 1121
Bengali (bn), 0214 Kirghiz (ky), 1125
Tibetan (bo), 0215 Latin (la), 1201
Breton (br), 0218 Lingala (ln), 1214
Catalan (ca), 0301 Laothian (lo), 1215
Corsican (co), 0315 Lithuanian (lt), 1220
Czech (cs), 0319 Latvian (lv), 1222
Welsh (cy), 0325 Malagasy (mg), 1307
Danish (da), 0401 Maori (mi), 1309
Bhutani (dz), 0426 Macedonian (mk), 1311
Esperanto (eo), 0515 Malayalam (ml), 1312
Estonian (et), 0520 Mongolian (mn), 1314
Basque (eu), 0521 Moldavian (mo), 1315
Persian (fa), 0601 Marathi (mr), 1318
Finnish (fi), 0609 Malay (ms), 1319
Fiji (fj), 0610 Maltese (mt), 1320
Faroese (fo), 0615 Burmese (my), 1325
Nauru (na), 1401 Siswati (ss), 1919
Nepali (ne), 1405 Sesotho (st), 1920
Norwegian (no), 1415 Sundanese (su), 1921
Occitan (oc), 1503 Swahili (sw), 1923
Oromo (om), 1513 Tamil (ta), 2001
Oriya (or), 1518 Telugu (te), 2005
Panjabi (pa), 1601 Tajik (tg), 2007
Polish (pl), 1612 Thai (th), 2008
Pashto, Pushto (ps), 1619 Tigrinya (ti), 2009
Quechua (qu), 1721 Turkmen (tk), 2011
Rhaeto-Romance (rm), 1813 Tagalog (tl), 2012
Kirundi (rn), 1814 Setswana (tn), 2014
Romanian (ro), 1815 Tonga (to), 2015
Kinyarwanda (rw), 1823 Turkish (tr), 2018
Sanskrit (sa), 1901 Tsonga (ts), 2019
Sindhi (sd), 1904 Tatar (tt), 2020
Sangho (sg), 1907 Twi (tw), 2023
Serbo-Croatian (sh), 1908 Ukrainian (uk), 2111
Sinhalese (si), 1909 Urdu (ur), 2118
Slovak (sk), 1911 Uzbek (uz), 2126
Slovenian (sl), 1912 Vietnamese (vi), 2209
Samoan (sm), 1913 Volapük (vo), 2215
Shona (sn), 1914 Wolof (wo), 2315
Somali (so), 1915 Xhosa (xh), 2408
Albanian (sq), 1917 Yoruba (yo), 2515
Serbian (sr), 1918 Zulu (zu), 2621
United States, 2119, us Chile, 0312, cl
Argentina, 0118, ar Denmark, 0411, dk
United Kingdom, 0702, gb Germany, 0405, de
Italy, 0920, it Japan, 1016, jp
India, 0914, in New Zealand, 1426, nz
Indonesia, 0904, id Norway, 1415, no
Australia, 0121, au Pakistan, 1611, pk
Austria, 0120, at Philippines, 1608, ph
Netherlands, 1412, nl Finland, 0609, fi
Canada, 0301, ca Mexico, 1324, mx
Korea, Republic of, 1118, kr Russian Federation, 1821, ru
Singapore, 1907, sg Brazil, 0218, br
Switzerland, 0308, ch France, 0618, fr
Sweden, 1905, se Belgium, 0205, be
Spain, 0519, es Portugal, 1620, pt
Thailand, 2008, th Hong Kong, 0811, hk
Taiwan, 2023, tw Malaysia, 1325, my
China, 0314, cn
X-SMC1_SYXZT8_En.book 35 ページ 2011年6月15日 水曜日 午後4時44分
Page: 35
Additional information
13
36
En
Setting the TV system
• This setting is available for a disc or USB storage device
content. For iPod/iPhone's TV out setting, operate your
iPod/iPhone.
• If the picture of the disc being played is distorted, switch
the TV system to the one used in your country or region.
• When the TV system is switched, the types of discs that
can be played are limited.
• The factory default setting is AUTO.
1 Press  STANDBY/ON to turn the unit's
power off.
2 Press  STANDBY/ON while pressing
VOLUME +.
Use the buttons on the unit's top panel.
The power turns on and the TV system switches as shown
below.
• AUTO  NTSC
• NTSC  PAL
• PAL  AUTO
Cautions on use
When moving this unit
When moving this unit, be sure to first check that there is no
disc loaded and disconnect the iPod/iPhone. Then press
STANDBY/ON on this unit (or STANDBY/ON on the remote
control), wait for the POWER ON indicator on the front panel
display to turn off, then unplug the power cord. Damage may
occur if the unit is transported or moved with a disc inserted,
or when another device is connected to the iPod/iPhone
connector port, USB terminal, or AUX IN mini-plug jack.
Place of installation
• Choose a stable place near the TV or stereo system being
used with this unit.
• Do not place this unit on top of a TV or color monitor.
Also install it away from cassette decks and other
devices easily affected by magnetic forces.
Avoid the following locations:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot places
• Places exposed to vibrations
• Places in which there is much dust or cigarette smoke
• Places exposed to soot, steam or heat (kitchens, etc.)
Do not place objects on this unit.
Do not place any objects on top of this unit.
Do not obstruct the ventilation holes.
Do not use this unit on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Do not expose to heat.
Do not place this unit on top of an amplifier or other
component that generates heat. When rack mounting it, to
avoid the heat given off by the amplifier or other audio
component, place it on a shelf below the amplifier.
• Turn off the unit’s power when not using it.
• Depending on signal conditions, striped patterns may
appear on a TV screen and noise may enter the sound of
radio broadcasts when the unit’s power is on. If this
happens, turn the unit’s power off.
About condensation
If this unit is moved suddenly from a cold place into a warm
room (in winter, for example) or if the temperature in the room
in which this unit is installed rises suddenly due to heater
operation, etc., water droplets (condensation) may form
inside (on operating parts and the lens). When condensation
is present, this unit will not operate properly and playback is
not possible. Let this unit stand at room temperature for 1 or
2 hours with the power turned on (the time depends on the
extent of condensation). The water droplets will dissipate and
playback will become possible. Condensation can also occur
in the summer if this unit is directly exposed to the air flow
from an air-conditioner. If this happens, move this unit to a
different place.
Cleaning the product
• Unplug the power cord from the power outlet when
cleaning this unit.
• Clean this unit using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a
soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a soft, dry cloth.
• Alcohol, thinner, benzene, insecticides, etc., could
cause the print or paint to peel off. Also, leaving rubber
or vinyl products in contact with this unit for long periods
of time could mar the cabinet.
• When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.
Types of
discs/files
Format Playing setting
NTSC PAL AUTO
NTSC NTSC PAL NTSC
PAL NTSC PAL PAL
no disc
- NTSC PAL NTSC
or PAL
X-SMC1_SYXZT8_En.book 36 ページ 2011年6月15日 水曜日 午後4時44分
Page: 36
Additional information 13
37
En
English
Français
Español
Cleaning the lens
• This unit’s lens should not become dirty in normal use,
but if for some reason it should malfunction due to dust
or dirt, consult your nearest Pioneer authorized service
center. Although lens cleaners for players are
commercially available, we advise against using them
since some may damage the lens.
About copyrights
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and
disassembly are prohibited.
Handling discs
Storing
• Always place discs in their cases and store them
vertically, avoiding hot, humid places, places exposed to
direct sunlight and extremely cold places.
• Be sure to read the cautions included with the disc.
Cleaning discs
• Discs may not play if there are fingerprints or dust on
them. In this case, use a cleaning cloth, etc., to gently
wipe the disc from the inside towards the outside. Do not
use dirty cleaning cloths.
• Do not use benzene, thinner or other volatile chemicals.
Also do not use record spray or antistatic agents.
• For tough dirt, apply some water to a soft cloth, wring out
thoroughly, wipe off the dirt, then wipe off the moisture
with a dry cloth.
• Do not use damaged (cracked or warped) discs.
• Do not let the signal surface of discs get scratched or
dirty.
• Do not attach pieces of paper or stickers to discs. Doing
so could warp discs, making it impossible to play them.
Also note that rental discs often have labels attached to
them, and the label’s glue may have oozed out. Check
that there is no glue around the edges of such labels
before using rented discs.
About specially shaped discs
Specially shaped discs (heart-shaped, hexagonal, etc.)
cannot be played on this unit. Do not attempt to play such
discs, as they could damage this unit.
About iPod/iPhone
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod
touch are trademarks of Apple Inc., registered in the U.S. and
other countries.
X-SMC1_SYXZT8_En.book 37 ページ 2011年6月15日 水曜日 午後4時44分
Page: 37
Additional information
13
38
En
Specifications
• Amplifier section
RMS Power Output:
Front Left/Right . . . . . . . . . . . . . . . . . . . . . . .20 W + 20 W
(1 kHz, 10 %, T.H.D., 8 Ω)
• Speaker section
Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . Passive radiator
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-way system
Speakers:
Fullrange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 cm cone
Passive radiator . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm cone
Frequency range . . . . . . . . . . . . . . . . . . . .60 Hz to 20 kHz
• Miscellaneous
iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 1 A
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 V, 500 mA
AS-BT200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 V, 100 mA
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 W
On standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W
Dimensions
. . . . . . . . . . . . . . . .520 mm (W) x 218 mm (H) x 156 mm (D)
Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . 3.7 kg
• AC adapter
Power requirements . . . . . . . AC 100 V to 240 V, 50 Hz/60 Hz
Rated Output. . . . . . . . . . . . . . . . . . . . . . . . . .DC 19 V, 3.42 A
• Accessories
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AAA batteries (R03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Video cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AC adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord
Operating instructions (This document)
Note
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
• This product is not designed for use in Japan.
© 2011 PIONEER CORPORATION.
All rights reserved.
X-SMC1_SYXZT8_En.book 38 ページ 2011年6月15日 水曜日 午後4時44分
Page: 38
Additional information 13
39
En
English
Français
Español
X-SMC1_SYXZT8_En.book 39 ページ 2011年6月15日 水曜日 午後4時44分
Page: 72
Informations complémentaires 13
35
Fr
English
Français
Español
Tableau des codes de langues et Tableau
des codes de pays et régions
Tableau des codes de langues
Noms (codes) de langues et codes numériques:
Tableau des codes de pays et régions
Noms de pays et régions, Codes numériques et
Codes de pays et régions
Japanese (ja), 1001 Frisian (fy), 0625
English (en), 0514 Irish (ga), 0701
French (fr), 0618 Scots-Gaelic (gd), 0704
German (de), 0405 Galician (gl), 0712
Italian (it), 0920 Guarani (gn), 0714
Spanish (es), 0519 Gujarati (gu), 0721
Chinese (zh), 2608 Hausa (ha), 0801
Dutch (nl), 1412 Hindi (hi), 0809
Portuguese (pt), 1620 Croatian (hr), 0818
Swedish (sv), 1922 Hungarian (hu), 0821
Russian (ru), 1821 Armenian (hy), 0825
Korean (ko), 1115 Interlingua (ia), 0901
Greek (el), 0512 Interlingue (ie), 0905
Afar (aa), 0101 Inupiak (ik), 0911
Abkhazian (ab), 0102 Indonesian (in), 0914
Afrikaans (af), 0106 Icelandic (is), 0919
Amharic (am), 0113 Hebrew (iw), 0923
Arabic (ar), 0118 Yiddish (ji), 1009
Assamese (as), 0119 Javanese (jw), 1023
Aymara (ay), 0125 Georgian (ka), 1101
Azerbaijani (az), 0126 Kazakh (kk), 1111
Bashkir (ba), 0201 Greenlandic (kl), 1112
Byelorussian (be), 0205 Cambodian (km), 1113
Bulgarian (bg), 0207 Kannada (kn), 1114
Bihari (bh), 0208 Kashmiri (ks), 1119
Bislama (bi), 0209 Kurdish (ku), 1121
Bengali (bn), 0214 Kirghiz (ky), 1125
Tibetan (bo), 0215 Latin (la), 1201
Breton (br), 0218 Lingala (ln), 1214
Catalan (ca), 0301 Laothian (lo), 1215
Corsican (co), 0315 Lithuanian (lt), 1220
Czech (cs), 0319 Latvian (lv), 1222
Welsh (cy), 0325 Malagasy (mg), 1307
Danish (da), 0401 Maori (mi), 1309
Bhutani (dz), 0426 Macedonian (mk), 1311
Esperanto (eo), 0515 Malayalam (ml), 1312
Estonian (et), 0520 Mongolian (mn), 1314
Basque (eu), 0521 Moldavian (mo), 1315
Persian (fa), 0601 Marathi (mr), 1318
Finnish (fi), 0609 Malay (ms), 1319
Fiji (fj), 0610 Maltese (mt), 1320
Faroese (fo), 0615 Burmese (my), 1325
Nauru (na), 1401 Siswati (ss), 1919
Nepali (ne), 1405 Sesotho (st), 1920
Norwegian (no), 1415 Sundanese (su), 1921
Occitan (oc), 1503 Swahili (sw), 1923
Oromo (om), 1513 Tamil (ta), 2001
Oriya (or), 1518 Telugu (te), 2005
Panjabi (pa), 1601 Tajik (tg), 2007
Polish (pl), 1612 Thai (th), 2008
Pashto, Pushto (ps), 1619 Tigrinya (ti), 2009
Quechua (qu), 1721 Turkmen (tk), 2011
Rhaeto-Romance (rm), 1813 Tagalog (tl), 2012
Kirundi (rn), 1814 Setswana (tn), 2014
Romanian (ro), 1815 Tonga (to), 2015
Kinyarwanda (rw), 1823 Turkish (tr), 2018
Sanskrit (sa), 1901 Tsonga (ts), 2019
Sindhi (sd), 1904 Tatar (tt), 2020
Sangho (sg), 1907 Twi (tw), 2023
Serbo-Croatian (sh), 1908 Ukrainian (uk), 2111
Sinhalese (si), 1909 Urdu (ur), 2118
Slovak (sk), 1911 Uzbek (uz), 2126
Slovenian (sl), 1912 Vietnamese (vi), 2209
Samoan (sm), 1913 Volapük (vo), 2215
Shona (sn), 1914 Wolof (wo), 2315
Somali (so), 1915 Xhosa (xh), 2408
Albanian (sq), 1917 Yoruba (yo), 2515
Serbian (sr), 1918 Zulu (zu), 2621
Etats-Unis, 2119, us Chili, 0312, cl
Argentine, 0118, ar Danemark, 0411, dk
Royaume-uni, 0702, gb Allemagne, 0405, de
Italie, 0920, it Japon, 1016, jp
Inde, 0914, in Nouvelle-Zélande, 1426, nz
Indonésie, 0904, id Norvège, 1415, no
Australie, 0121, au Pakistan, 1611, pk
Autriche, 0120, at Philippines, 1608, ph
Pays-Bas, 1412, nl Finlande, 0609, fi
Canada, 0301, ca Mexique, 1324, mx
Corée, République de, 1118, Fédération russe, 1821, ru
Singapour, 1907, sg Brésil, 0218, br
Suisse, 0308, ch France, 0618, fr
Suède, 1905, se Belgique, 0205, be
Espagne, 0519, es Portugal, 1620, pt
Thaïlande, 2008, th Hong Kong, 0811, hk
Taiwan, 2023, tw Malaisie, 1325, my
Chine, 0314, cn
X-SMC1_SYXZT8_En.book 35 ページ 2011年6月15日 水曜日 午後8時19分
Page: 115
Printed in Thailand / Imprimé en Thaïlande
© 2011 PIONEER CORPORATION.
All rights reserved.
© 2011 PIONEER CORPORATION.
Tous droits de reproduction et de traduction réservés.
J2P30131C SH N 00/00
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
http://www.pioneer.co.uk
http://www.pioneer.fr
http://www.pioneer.es
http://www.pioneer.eu
X-SMC1_SYXZT8_BackCover.fm 38 ページ 2011年11月29日 火曜日 午後3時33分

Question & answers

There are no questions about the Pioneer X-SMC1-S yet.

Ask a question about the Pioneer X-SMC1-S

Have a question about the Pioneer X-SMC1-S but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer X-SMC1-S. Please make sure that you describe your difficulty with the Pioneer X-SMC1-S as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.