View a manual of the Pioneer X-HM11-K below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. D3-4-2-1-1_B1_En WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture. D3-4-2-1-3_A1_En WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment. D3-4-2-1-7a_A1_En VENTILATION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 25 cm at top, 10 cm at rear, and 5 cm at each side). WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D3-4-2-1-7b*_A1_En Operating Environment Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c*_A1_En WARNING Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately. D41-6-4_A1_En This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_A1_En CAUTION The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power plug can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D3-4-2-2-2a*_A1_En POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. S002*_A1_En Do not install your speakers overhead on the ceiling or wall. The grill is designed to be detachable, and as such it may fall and cause damage or personal injury if installed overhead. SGK004_A1_En CAUTION This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007. CLASS 1 LASER PRODUCT D58-5-2-2a_A1_En
Information for users on collection and disposal of old equipment and used batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. These symbols are only valid in the European Union. For countries outside the European Union: If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. K058a_A1_En Symbol examples for batteries Symbol for equipment Pb
4 En Thank you for buying this Pioneer product. Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference. Contents 01 Before you start What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Loading the batteries in the remote control . . . . . . . . . 5 Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . 5 02 Part names and functions Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 03 Connections Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . . 11 Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 04 Getting started To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Input function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Display brightness control . . . . . . . . . . . . . . . . . . . . . . . 12 Volume auto setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Muting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 P.BASS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . 13 Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . 14 Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . . . 14 Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 14 Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 05 iPod/iPhone/iPad playback (X-HM21 only) Confirming what iPod/iPhone/iPad models are supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . 15 Connecting iPod/iPhone/iPad using supplied stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Playing iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . 16 06 Disc playback Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Advanced CD or MP3/WMA disc playback . . . . . . . . . 18 Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Programmed play (CD or MP3/WMA) . . . . . . . . . . . . . . 19 About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . 19 About folder playback order . . . . . . . . . . . . . . . . . . . . . . 19 Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 20 Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 20 07 USB playback Playing USB storage devices . . . . . . . . . . . . . . . . . . . . 21 Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 22 Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 22 Playing in the desired order (Programmed Play) . . . . 22 08 Using the tuner Listening to the radio broadcasts . . . . . . . . . . . . . . . . 23 Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . . . 23 To recall a memorised station . . . . . . . . . . . . . . . . . . . . 24 To scan the preset stations. . . . . . . . . . . . . . . . . . . . . . . 24 To erase entire preset memory. . . . . . . . . . . . . . . . . . . . 24 Using the Radio Data System (RDS) . . . . . . . . . . . . . . 24 An introduction to RDS. . . . . . . . . . . . . . . . . . . . . . . . . . 24 Searching for RDS programs. . . . . . . . . . . . . . . . . . . . . 24 Information provided by RDS . . . . . . . . . . . . . . . . . . . . . 25 Using the Auto Station Program Memory (ASPM). . . . 25 Notes for RDS operation. . . . . . . . . . . . . . . . . . . . . . . . . 25 09 Other connections Connecting auxiliary components . . . . . . . . . . . . . . . . 26 10 Additional information Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Playable discs and formats . . . . . . . . . . . . . . . . . . . . . 29 Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . 29 Supported audio file formats . . . . . . . . . . . . . . . . . . . . . 29 Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Do not place objects on this unit . . . . . . . . . . . . . . . . . . 30 About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cleaning the lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 About specially shaped discs. . . . . . . . . . . . . . . . . . . . . 30 About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . 31 Restoring all the settings to the defaults . . . . . . . . . . 31 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Before you start 01 5 En English Français Español Chapter 1: Before you start What’s in the box Please confirm that the following accessories are in the box when you open it. • Remote Control • Power cord • AM antenna cable • FM wire antenna • AAA batteries (R03) x 2 • iPad stand (X-HM21 only) • Warranty card • Operating instructions (this document) Loading the batteries in the remote control 1 Open the rear lid and load the batteries as illustrated below. 2 Close the rear lid. CAUTION • When inserting the batteries, make sure not to damage the springs on the battery’s terminals. This can cause batteries to leak or over heat. • Do not use any batteries other than the ones specified. Also, do not use a new battery together with an old one. • When loading the batteries into the remote control, set them in the proper direction, as indicated by the polarity marks ( and ). • Do not heat batteries, disassemble them, or throw them into flames or water. • Batteries may have different voltages, even if they are the same size and shape. Do not use different types of batteries together. • To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water. • When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area. • WARNING Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries. Using the remote control The remote has a range of about 7 m at an angle of about 30º from the remote sensor. Keep in mind the following when using the remote control: • Make sure that there are no obstacles between the remote and the remote sensor on the unit. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor. • Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit. • Replace the batteries when you notice a fall off in the operating range of the remote. INPU T 30° 7 m 30°
Part names and functions 02 6 En Chapter 2: Part names and functions Remote control 1 STANDBY/ON Switches the receiver between standby and on (page 12). 2 Input function buttons Use to select the input source to this receiver (pages 16, 17, 21, 23, 26). 3 CD Receiver control buttons CLOCK/TIMER Use for setting the clock, as well as for setting and checking the timers (page 12). SLEEP See Using the sleep timer on page 14. 4 Numeric buttons (0 to 9) Use to enter the number (page 18). 5 CLEAR Use to clear the programmed play (page 19). 6 CD Receiver control buttons DISPLAY Press to change the display for songs playing back from CD or USB (page 20). FOLDER Use to select the folder of the MP3/WMA disc or USB mass storage device (page 19). MENU Use to access the menu. MEMORY/PROGRAM Use to memory or program the MP3/WMA disc (page 19). 7 F/G/H/I (TUNE +/–), ENTER Use to select/switch system settings and modes, and to confirm actions. Use TUNE +/– can be used to find radio frequencies (page 23). 8 PRESET +/– Use to select preset radio stations (page 24). 9 MUTE Mutes/unmutes the sound (page 12). 10 Playback control buttons Use to control each function after you have selected it using the input function buttons (page 17). 4 5 1 3 2 6 7 8 12 17 13 14 9 10 11 16 15 STANDBY/ON CD USB TUNER AUDIO IN DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BASS BASS/TREBLE RANDOM CLEAR REPEAT OPEN/CLOSE RDS ENTER OPTION
Part names and functions 02 7 En English Français Español 11 Tuner control buttons ST/MONO Use to switch the sound mode between stereo and monaural. (page 23) RDS ASPM Use to search for RDS Auto station program memory (page 24). RDS PTY Use to search for RDS program types (page 24). RDS DISPLAY Press to change the RDS display for information mode (page 24). 12 OPEN/CLOSE Use to open or close the disc tray (page 17). 13 Sound control buttons Adjust the sound quality (page 13). 14 RANDOM Randomize order of track playback from a CD, iPod or USB (page 18). 15 REPEAT Press to change the repeat play setting from a CD, iPod or USB (page 18). 16 Volume control buttons Use to set the listening volume (page 12). 17 DIMMER Dims or brightens the display. The brightness can be controlled in four steps (page 12). Note • The BT AUDIO button is not available for this unit. Speaker system 1 Tweeter 2 Woofer 3 Bass Reflex Duct Important • Speaker grille cannot be removed. (X-HM11) • Make sure nothing comes into contact with the speaker diaphragms when you remove the speaker grilles. (X- HM21) 1 2 3
Part names and functions 02 8 En Front panel 1 STANDBY/ON button Switches the receiver between standby and on (page 12). 2 Remote sensor Receives the signals from the remote control. 3 TIMER indicator Lights when the unit power is off but when the timer setting is activated. 4 Character display See Display on page 9. 5 Volume control Use to set the listening volume (page 12). 6 INPUT button Selects the input source. 7 Headphone socket Use to connect headphones. When the headphones are connected, there is no sound output from the speakers (page 14). 8 AUDIO IN socket Use to connect an auxiliary component using a stereo minijack cable (page 26). 9 USB terminal (X-HM21) Use to connect your USB mass storage device or Apple iPod/ iPhone/iPad as an audio source (page 21). USB terminal (X-HM11) Use to connect your USB mass storage device as an audio source (page 21). 10 Disc tray Place the disc, label side up (page 17). 11 Playback control buttons Select the desired track or file to be played back. Stop current playback. Stop playback or resume playback from the point where it was paused. 12 Disc tray open/close button Use to open or close the disc tray (page 17). STANDBY/ON INPUT VOLUME PHONES AUDIO IN TIMER X-HM21 X-HM21 7 8 6 9 11 12 10 2 5 1 3 4
Part names and functions 02 9 En English Français Español Display 1 Lights when the sound is muted. Note • The mute icon will be displayed in red. 2 Start playback. 3 Pause playback. 4 Timer function is set. 5 Character display Displays various system information. 1 3 2 4 5
Connections 03 10 En Chapter 3: Connections CAUTION • Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections. • Connect the power cord after all the connections between devices have been completed. Speaker connection • Push open the tabs and insert exposed wire. • Connect the black wire to (–) terminal, and the red wire to the (+) terminal. CAUTION • These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts. • Do not connect any speakers other than those supplied to this system. • Do not connect the supplied speakers to any amplifier other than the one supplied with this system. Connection to any other amplifier may result in malfunction or fire. • Do not attach these speakers to the wall or ceiling. They may fall off and cause injury. • These speakers are magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker system is installed extremely close to the screen of a television set. If this happens, turn off the television set, and then turn it on after 15 to 30 minutes. If the problem persists, move the speaker system away from the television set. • Make sure that the speaker cable cores do not become exposed and make contact with other cable cores. This may cause malfunction of the product. • Do not allow the speaker cable core to come into contact with the receiver body. - If the speaker cable core comes into contact with any metal portion of the receiver’s body, it may damage the speakers and cause smoke and fire. Insert speaker cables securely into the terminals and check that the cable does not come out of easily. Note • There is no difference between L and R speakers. SPEAKERS LINE IN L R R L Left speaker Right speaker This unit’s rear panel
Connections 03 11 En English Français Español Connecting antennas Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). 1 Connect the AM antenna wires. Hold the terminal part of the wire when connecting. 2 Fix the AM loop antenna to the attached stand. To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the stand (fig. b). 3 Place the AM antenna on a flat surface and in a direction giving the best reception. 4 Connect the FM wire antenna into the FM antenna socket. For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up. Using external antennas To improve FM reception Use a PAL connector (not supplied) to connect an external FM antenna. Plugging in CAUTION • Do not use any power cord other than the one supplied with this unit. • Do not use the supplied power cord for any purpose other than that described below. Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. After you’ve finished making all connections, plug the unit into an AC outlet. AM LOOP ANTENNA FM UNBAL 75 Ω 2 1 3 4 fig. a fig. b ANTENNA FM UNBAL 75 Ω One-touch PAL connector 75 coaxial cable AC IN To AC outlet This unit’s rear panel Power cord
Getting started 04 12 En Chapter 4: Getting started To turn the power on Press the STANDBY/ON to turn the power on. After use: Press the STANDBY/ON to enter the power stand-by mode. Note • In standby mode, if iPod/iPhone/iPad is connected, the unit turns charge mode. Setting the clock 1 Press STANDBY/ON to turn the power on. 2 Press CLOCK/TIMER on the remote control. “CLOCK” is shown on the main display. 3 Press ENTER. 4 Press HI to set the day, then press ENTER. 5 Press HI to set the hour, then press ENTER. 6 Press HI to set the minute, then press ENTER to confirm. 7 Press ENTER. To confirm the time display: Press the CLOCK/TIMER. The time display will appear for about 10 seconds. To readjust the clock: Perform “Setting the clock” from step 1. Note • When power supply is restored after unit is plugged in again or after a power failure, reset the clock. General control Input function When the INPUT on main unit is pressed, the current function will change to different mode. Press the INPUT repeatedly to select desired function. X-HM21 X-HM11 Display brightness control Press DIMMER to dims the display brightness. The brightness can be controlled in four steps. Volume auto setting If you turn off and on the main unit with the volume set to 31 or higher, the volume starts at 30 and sets in to the last set level. Volume control Turn the VOLUME on the unit or press VOLUME +/– on the remote control to increase or decrease the volume. CAUTION • The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. It is advisable to avoid exposure to high volume levels. Do not turn the volume on to full at switch on. Listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss. Muting The volume is muted temporarily when pressing the MUTE on the remote control. Press again to restore the volume. STANDBY/ON CD USB TUNER AUDIO IN 1 2 3 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER OPEN/CLOSE DISPLAY FOLDER MENU PRESET VOLUME TUNE– TUNE+ MEMORY /PROGRAM ENTER CD AM USB/iPod FM AUDIO IN LINE CD AM USB FM AUDIO IN LINE
Getting started 04 13 En English Français Español Sound controls Equalizer When the EQUALIZER is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER repeatedly until the desired sound mode appears. P.BASS control When the power is first turned on, the unit will enter the P.BASS mode which emphasises the bass frequencies. To cancel the P.BASS mode, press the P.BASS on the remote control. Bass/treble control Press the BASS/TREBLE, then press FG/HI to adjust the bass or treble. Note Simultaneous operation of EQUALIZER, P.BASS and BASS/ TREBLE is not possible. Only the functions that you have selected will be active. If you select one of three functions, features that are not selected will be set as follows. 1 If you change the settings of P.BASS (ON/ OFF). • EQUALIZER : FLAT • BASS/TREBLE : BASS=0, TREBLE=0 2 If you change the settings of EQUALIZER. • P.BASS : OFF • BASS/TREBLE : BASS=0, TREBLE=0 3 If you change the settings of BASS/TREBLE. • P.BASS : OFF • EQUALIZER : FLAT Setting the wake-up timer Used to change the existing timer setting, or to set a new timer. 1 Press STANDBY/ON to turn the power on. 2 Press and hold CLOCK/TIMER. 3 Press HI to select “ONCE” or “DAILY”, then press ENTER. ONCE – Works once only at a preset time. DAILY – Works at the preset time on a preset day. 4 Press HI to select “TIMER SET”, then press ENTER. 5 Press HI to select the timer playback source, then press ENTER. • CD, FM, AM, USB/iPod, USB, AUDIO IN and LINE can be selected as the playback source. 6 Press HI to select the timer day, then press ENTER. 7 Press HI to set the hour, then press ENTER. 8 Press HI to set the minute, then press ENTER. • Set the time to finish as in steps 7 and 8 above. 9 Adjust the volume press VOLUME +/– , then press ENTER. 10 Press STANDBY/ON to enter the power standby mode. • The TIMER indicator lights up. NIGHT FLAT A flat and basic sound. ACTIVE DIALOGUE A sound that can be enjoyed at night even with lower volume. A powerful sound that emphasizes low and high tones. A sound that allows the radio or vocals to be heard more easily.
Getting started 04 14 En Calling the wake-up timer An existing timer setting can be reused. 1 Follow steps 1 to 3 in “Setting the wake-up timer”. 2 Press HI to select “TIMER ON”, then press ENTER. Cancelling the wake-up timer Turn off the timer setting. 1 Follow steps 1 to 3 in “Setting the wake-up timer”. 2 Press HI to select “TIMER OFF”, then press ENTER. Using the wake-up timer 1 Press STANDBY/ON to turn the power off. 2 At the wake-up time, this unit will turn on automatically and play the selected input function. Note • If at the wake-up time an iPod/iPhone/iPad is not connected to the unit or a disc is not inserted, the unit will be turned on but will not play back the track. • Some discs may not be played automatically at the wake- up time. • When setting the timer set at least one minute between the start and end time. Using the sleep timer The sleep timer switches off the unit after a specified time so you can fall asleep without worrying about it. 1 Press SLEEP repeatedly to select a switch off time. Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120 min, 150 min, 180 min or OFF. The newly set value displays for 3 seconds, and then the setting is completed. Note • The sleep timer can be set by pressing SLEEP while the remaining time is displayed. Using Headphones Insert the headphone’s jack plug into the connector. When the headphones are connected, there is no sound output from the speakers. • Do not turn the volume on to full at switch on and listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss. • Before plugging in or unplugging the headphone, reduce the volume. • Be sure your headphone has a 3.5 mm diameter plug and impedance between 16 and 50 . The recommended impedance is 32 . • Audio from the iPod/iPhone/iPad cannot be heard via the headphones connected to the unit. “HP MUTE” will be displayed if you connect the headphones when the iPod/iPhone/iPad function is selected. STANDBY/ON INPUT VOLUME PHONES AUDIO IN TIMER X-HM21
iPod/iPhone/iPad playback (X-HM21 only) 05 15 En English Français Español Chapter 5: iPod/iPhone/iPad playback (X-HM21 only) Merely by connecting your iPod/iPhone/iPad to this unit, you can enjoy high-quality sound from your iPod/iPhone/iPad. Playback setting for iPod/iPhone/iPad music can be performed from this unit or the iPod/iPhone/iPad itself. Confirming what iPod/iPhone/iPad models are supported The iPod/iPhone/iPad playable on this unit are shown below. Note • Pioneer does not guarantee that this unit plays iPod/ iPhone/iPad models other than the ones specified. • Some functions may be restricted depending on the model or software version. • iPod/iPhone/iPad is licensed for reproduction of non- copyrighted materials or materials the user is legally permitted to reproduce. • Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizer off before connecting. • Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience or loss of recorded material resulting from iPod/iPhone/iPad failure. • For detailed instructions on using the iPod/iPhone/iPad, please refer to the manual supplied with the iPod/ iPhone/iPad. • This system has been developed and tested for the software version of iPod/iPhone/iPad indicated on the website of Pioneer (http://pioneer.jp/homeav/support/ ios/eu/). • Installing software versions other than indicated on the website of Pioneer to your iPod/iPhone/iPad may result in incompatibility with this system. • This unit cannot be used to record CD, tuner or other content on an iPod/iPhone/iPad. Connecting your iPod/iPhone/iPad Connecting iPod/iPhone/iPad using supplied stand 1 Connect the iPod/iPhone/iPad cable to the unit. 2 Pass the iPod/iPhone/iPad cable through the bottom of the stand and connect it to the iPod/ iPhone/iPad. 3 Set the iPod/iPhone/iPad on the stand. iPod/iPhone/iPad USB Terminal (Audio only) iPod nano 3G/4G/5G/6G/7G iPod touch 1G/2G/3G/4G/5G iPhone 5 iPhone 4S iPhone 4 iPhone 3GS iPhone 3G iPhone iPad mini iPad (4th generation) iPad (3rd generation) iPad 2 iPad
iPod/iPhone/iPad playback (X-HM21 only) 05 16 En Playing iPod/iPhone/iPad 1 Connect your iPod/iPhone/iPad. • If an iPod/iPhone/iPad is connected while the unit is turned on, playback of the iPod/iPhone/iPad will not begin. 2 Press USB as the input source. “USB/iPod” is shown on the main display. 3 When the recognition is completed, will begin playing automatically. • The available iPod/iPhone/iPad playback controls from the unit are , , . • In the following case, operate your iPod/iPhone/iPad directly: - Searching a file by artist name or genre. - Playing in the repeat or random mode. CAUTION • When your iPod/iPhone/iPad is connected to this unit and you wish to operate the iPod/iPhone/iPad directly, be sure to steady the iPod/iPhone/iPad with the other hand to prevent malfunctions due to faulty contacts. Note • For detailed instructions on using the iPod/iPhone/iPad, please refer to the manual supplied with the iPod/ iPhone/iPad. • iPod/iPhone/iPad recharging occurs whenever an iPod/ iPhone/iPad is connected to this unit. (This function is supported in standby mode as well.) • When input is switched from USB/iPod to another function, iPod/iPhone/iPad playback is temporarily stopped. Important If this unit cannot play your iPod/iPhone/iPad, perform the following troubleshooting checks: • Check whether the iPod/iPhone/iPad is supported by this unit. • Reconnect the iPod/iPhone/iPad to the unit. If this doesn’t seem to work, try resetting your iPod/iPhone/ iPad. • Check that iPod/iPhone/iPad software is supported by the unit. If the iPod/iPhone/iPad cannot be operated, check the following items: • Is the iPod/iPhone/iPad connected correctly? Reconnect the iPod/iPhone/iPad to the unit. • Is the iPod/iPhone/iPad experiencing a hangup? Try resetting the iPod/iPhone/iPad, and reconnect it to the unit.
Disc playback 06 17 En English Français Español Chapter 6: Disc playback This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 or WMA files, but cannot record on them. Some audio CD-R and CD-RW discs may not be playable due to the state of the disc or the device that was used for recording. MP3: MP3 is a form of compression. It is an acronym which stands for MPEG Audio Layer 3. MP3 is a type of audio code which is processed by significant compression from the original audio source with very little loss in sound quality. • This system supports MPEG-1/2 Audio Layer 3 (Sampling rates: 8 kHz to 48 kHz; Bit rates: 64 kbps to 384 kbps). • During VBR file playback, time counter in the display may differ from its actual playback time. WMA: WMA (Windows Media Audio) files are Advanced System Format files that include audio files which are compressed with Windows Media Audio codec. WMA is developed by Microsoft as an audio format file for Windows Media Player. • This system supports WMA (Sampling rates: 32 kHz/44.1 kHz/48 kHz; Bit rates: 64 kbps to 320 kbps). • During VBR file playback, time counter in the display may differ from its actual playback time. Playing discs or files 1 Press STANDBY/ON to turn the power on. 2 Press CD on the remote control or INPUT repeatedly on the main unit to select CD input. 3 Press OPEN/CLOSE to open the disc tray. 4 Place the disc on the disc tray, label side up. 5 Press OPEN/CLOSE to close the disc tray. 6 Press to start playback. After the last track is played, the unit will stop automatically. CAUTION • Do not place two discs in one disc tray. • Do not play discs of special shapes (heart, octagon, etc). It may cause malfunctions. • Do not push the disc tray whilst it is moving. • If the power fails whilst the tray is open, wait until the power is restored. • Be sure to place 8 cm disc in the middle of the disc tray. Note • Due to the structure of the disc information, it takes longer to read an MP3/WMA disc than a normal CD (approximately 20 to 90 seconds). • When the beginning of the first track is reached during fast reverse, the unit will enter the playback mode (only for CD). • Rewritable multi-session discs with unfinished writing, can still be played. • If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. Tip • When no operation has done in CD mode and the audio file is not played for more than 30 minutes, the power will automatically turn off. Various disc functions Function Main unit Remote control Operation Play Press in the stop mode. Stop Press in the playback mode. Pause Press in the playback mode. Press to resume playback from the paused point. Track up/ down Press in the playback or stop mode. If you press the button in the stop mode, press to start the desired track. Fast forward/ reverse Press and hold down in the playback mode. Release the button to resume playback.
Disc playback 06 18 En Advanced CD or MP3/WMA disc playback Direct track search By using the numeric buttons, the desired tracks on the current disc can be played. Use the numeric buttons on the remote control to select the desired track whilst playing the selected disc. Note • A track number higher than the number of tracks on the disc cannot be selected. To stop playback: Press . Repeat play Repeat play can play one track, all tracks or a programmed sequence continuously. To repeat one track: Press REPEAT repeatedly until “REPEAT ONE” appears. Press ENTER. To repeat all tracks: Press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To repeat desired tracks: Perform steps 1 to 5 in “Programmed play (CD or MP3/WMA)” section on next page and then press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To cancel repeat play: Press REPEAT repeatedly until “REPEAT OFF” appears. Press ENTER. Note • After performing repeat play, be sure to press . Otherwise, the disc will play continuously. • During repeat play, random play is not possible. Random play The tracks on the disc can be played in random order automatically. To random play all tracks: Press RANDOM repeatedly until “RANDOM ON” appears. Press ENTER. To cancel random play: Press RANDOM repeatedly until “RANDOM OFF” appears. Press ENTER. Note • If you press the during random play, you can move to the track selected next by the random operation. On the other hand, the does not allow you to move to the previous track. The beginning of the track being played will be located. • In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.) • During random play, repeat play is not possible. DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM 0 RDS ENTER STANDBY/ON CD USB TUNER AUDIO IN DISPLAY FOLDER TUNE+ 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BASS BASS/TREBLE RANDOM CLEAR REPEAT OPEN/CLOSE
Disc playback 06 19 En English Français Español Programmed play (CD or MP3/WMA) You can choose up to 32 selections for playback in the order you like. 1 Whilst in the stop mode, press MEMORY/ PROGRAM on the remote control to enter the programming save mode. 2 Press or the numeric buttons on the remote control to select the desired tracks. 3 Press ENTER to save folder and track number. 4 Repeat steps 2 to 3 for other folder/tracks. Up to 32 tracks can be programmed. • If you want to check the programmed tracks, press MEMORY/PROGRAM. • If you make a mistake, the last programmed tracks will be canceled by pressing CLEAR. 5 Press to start playback. To cancel the programmed play mode: To cancel the programmed play, press twice on the remote control. The display will show “PRG CLEAR” and all the programmed content will be cleared. Adding tracks to the program: Press the MEMORY/PROGRAM. Then follow steps 2 to 3 to add tracks. Note • When a disc is ejected anything programmed is cleared. • If you press the STANDBY/ON to enter the standby mode or change the function from CD to another, the programmed selections will be cleared. • During the program operation, random play is not possible. About downloading MP3/WMA There are many music sites on the internet that you can download MP3/WMA music files. Follow the instructions from the website on how to download the music files. You can then play back these downloaded music files by burning them to a CD-R/RW disc. • Your downloaded song/files are for personal use only. Any other usage of the song without owner’s permission, is against the law. About folder playback order If MP3/WMA files are recorded in several folders, a folder number will be set to each folder automatically. These folders can be selected by the FOLDER on the remote control. If there is no supported file formats inside the selected folder, the folder is skipped and the next folder will be selected. Example: How the folder numbers are assigned if MP3/WMA format files are recorded are as shown below. 1 ROOT folder is set as FOLDER 1. 2 As for folders inside ROOT folder (FOLDER A and FOLDER B), the folder which is recorded earlier on the disc will be set as FOLDER 2 and FOLDER 3. 3 As for folder inside FOLDER A (FOLDER C and FOLDER D), the folder which is recorded earlier on the disc will be set as FOLDER 4 and FOLDER 5. 4 FOLDER E that is inside FOLDER D will be set as FOLDER 6. • The folder and file order information which is recorded on the disc depends on the writing software. There maybe possibilities that this unit will playback the files not according to our expected playback order. • From a disc with MP3/WMA files up to 255 folders and 999 files (including non playable files) can be read. ROOT (FOLDER 1) FOLDER A (FOLDER 2) FOLDER B (FOLDER 3) FILE 9 FILE 10 FILE 3 FILE 4 FILE 5 FILE 6 FILE 7 FILE 8 FOLDER E (FOLDER 6) FOLDER C (FOLDER 4) FOLDER D (FOLDER 5) FILE 1 FILE 2
Disc playback 06 20 En Specify the folder to play To specify the folder to play, perform the following steps. 1 Press CD, and load an MP3/WMA disc. 2 Press FOLDER, and press FG to select desired playback folder. 3 Press ENTER. Playback will start from the first song of the selected folder. • Even if it is stopped, it is possible to press FG, to select a folder. Switch the display contents 1 Press DISPLAY. If the title, artist and album name has been written to the file, that information will be displayed. (The unit can only display alphanumeric characters. Non-alphanumeric character are displayed as ”*”.) Note • “Copyright protected WMA files” or “Unsupported files” cannot be played back. In these case the files will be skipped automatically. • There may be cases where no information can be displayed. • Displaying title, artist and album name is only supported for MP3 files. STANDBY/ON CD USB TUNER AUDIO IN DISPLAY FOLDER TUNE+ 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BASS BASS/TREBLE RANDOM CLEAR REPEAT OPEN/CLOSE DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM 0 RDS ENTER Title/Artist/Album display Number of track, playback time display File type display Number of folder/track display
USB playback 07 21 En English Français Español Chapter 7: USB playback Playing USB storage devices It is possible to listen to two-channel audio using the USB interface on the front of this receiver. • Pioneer does not guarantee that any file recorded on a USB storage device will play or that power will be supplied to a USB storage device. Also note that Pioneer will accept no responsibility whatsoever for loss of files on USB storage devices caused by connection to this unit. 1 Press USB as the input source. “USB/iPod” is shown on the main display. 2 Connect the USB storage device. The number of folders or files stored on the connected USB storage device appear on the main display automatically. • This receiver does not support a USB hub. • If an iPod/iPhone/iPad is connected to the unit, the unit will automatically begin charging it. 3 When the recognition is completed, press to start playback. • When changing to a different input source, stop the USB memory playback first before changing. 4 Disconnect USB storage device from the USB terminal. Turn the power off before removing the USB storage device. Note • USB flash drive that supports USB 2.0 can be used. • This unit may not recognize a USB storage device, play files or supply power to a USB storage device. For details, see When a USB storage device is connected on page 28. • When a USB storage device is not playing and no operations have been performed for more than 30 minutes, the unit will automatically power off. Repeat play Repeat play can play one track, all tracks or a programmed sequence continuously. To repeat one track: Press REPEAT repeatedly until “REPEAT ONE” appears. Press ENTER. To repeat all tracks: Press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To repeat desired tracks: Perform steps 1 to 5 in “Programmed play (CD or MP3/WMA)” section on next page and then press REPEAT repeatedly until “REPEAT ALL” appears. Press ENTER. To cancel repeat play: Press REPEAT repeatedly until “REPEAT OFF” appears. Press ENTER. Note • After performing repeat play, be sure to press . Otherwise, the file of USB storage device will play continuously. • During repeat play, random play is not possible. Random play The file of USB storage device can be played in random order automatically. To random play all tracks: Press RANDOM repeatedly until “RANDOM ON” appears. Press ENTER. To cancel random play: Press RANDOM repeatedly until “RANDOM OFF” appears. Press ENTER. Note • If you press the during random play, you can move to the track selected next by the random operation. On the other hand, the does not allow you to move to the previous track. The beginning of the track being played will be located. • In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.) • During random play, repeat play is not possible. PHONES AUDIO IN USB storage device (commercially available)
USB playback 07 22 En Specify the folder to play To specify the folder to play, perform the following steps. 1 Press USB, and connect the USB storage device. 2 Press FOLDER, and press FG to select desired playback folder. 3 Press ENTER. Playback will start from the first song of the selected folder. • Even if it is stopped, it is possible to press FG, to select a folder. Switch the display contents The unit can display the information recorded in the USB storage device. For details, see Switch the display contents on page 20. Playing in the desired order (Programmed Play) The unit can play folders stored on a USB storage device in the desired order. For details, see Programmed play (CD or MP3/WMA) on page 19.
Using the tuner 08 23 En English Français Español Chapter 8: Using the tuner Listening to the radio broadcasts The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later. See Saving station presets below for more on how to do this. Tuning 1 Press the STANDBY/ON to turn the power on. 2 Press TUNER repeatedly to select desired frequency band (FM or AM). 3 Press TUNE +/– on the remote control to tune in to the desired station. Automatic tuning: Press and hold TUNE +/–, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Manual tuning: Press the TUNE +/– repeatedly to tune in to the desired station. Note • When radio interference occurs, automatic tuning may stop automatically at that point. • Automatic tuning will skip weak signal stations. • To stop the automatic tuning, press . • When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first. Finally, the station name will appear. • Full auto tuning can be achieved for RDS stations using Auto Station Program Memory (ASPM) mode, see page 25. To receive an FM stereo transmission: • Press ST/MONO to select stereo mode and “AUTO” will be displayed. Improving poor FM reception: 1 Press ST/MONO repeatedly to select MONO. This will change the tuner from stereo to mono and usually improve the reception. Saving station presets If you often listen to a particular radio station, it’s convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station (Preset tuning). This saves the effort of manually tuning in each time. This unit can memorize up to 45 stations. (FM 30 stations/AM 15 stations) 1 Tune to a station you want to memorize. See Tuning above for more on this. 2 Press MEMORY/PROGRAM. The preset number will flash. 3 Press PRESET +/– to select the preset channel number. 4 Press MEMORY/PROGRAM to store that station in memory. If the preset number has changed from flashing to lighting, before the station is memorised, repeat the operation from step 2. • Repeat steps 1 to 4 to set other stations, or to change a preset station. When a new station is stored in the memory, the station previously memorised for that preset channel number will be erased. Note • The backup function protects the memorised stations for a few hours should there be a power failure or the AC power cord become disconnected. DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM 0 RDS ENTER STANDBY/ON CD USB TUNER AUDIO IN DISPLAY FOLDER TUNE+ 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BASS BASS/TREBLE RANDOM CLEAR REPEAT OPEN/CLOSE DISPLAY FOLDER MENU PRESET VOLUME + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM 0 ENTER DISPLAY FOLDER MENU PRESET VOLUME + MUTE TUNE– TUNE+ – + – MEMORY /PROGRAM 0 RANDOM CLEAR REPEAT ENTER
Using the tuner 08 24 En To recall a memorised station 1 Press PRESET +/– to select the desired station. To scan the preset stations The stations saved in the memory can be scanned automatically. (Preset memory scan) 1 Press and hold PRESET +/–. The preset number will appear and the programmed stations will be tuned in sequentially, for 5 seconds each. 2 Press PRESET +/– again when the desired station is located. To erase entire preset memory 1 Press TUNER on the remote control. 2 Press CLEAR until “MEMORY CLEAR” appears. Note • All stations will be erased. Using the Radio Data System (RDS) An introduction to RDS Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information—the name of the station and the kind of show they’re broadcasting, for example. One feature of RDS is that you can search by type of program. For example, you can search for a station that’s broadcasting a show with the program type, JAZZ. You can search the following program types: Searching for RDS programs You can search a program type listed above. 1 Press TUNER on the remote control. • RDS is only possible in the FM. 2 Press RDS PTY on the remote control. “SELECT” will appear for about 6 seconds. 3 Press HI to select the program type you want to hear. Each time the button is pressed, the program type will appear. If the button is held down, the program type will appear continuously. 4 Whilst the selected program type is displayed (within 6 seconds), Press RDS PTY again. After the selected program type has been lit for 2 seconds, “SEARCH” will appear, and the search operation will start. Note • If the display has stopped flashing, start again from step 2. If the unit finds a desired program type, the corresponding channel number will be lit for about 8 seconds, and then the station name will be displayed. News – News Current Affairs – Current Affairs Information – General Information Sport – Sport Education – Educational Drama – Radio plays, etc. Cultures – National or regional culture, theater, etc. Science – Science and technology Varied Speech – Usually talk- based material, such as quiz shows or interviews. Pop Music – Pop music Rock Music – Rock music Easy Listening – Easy listening Light Classics M – ‘Light’ classical music Serious Classics – ‘Serious’ classical music Other Music – Music not fitting above categories Weather & Metr – Weather reports Finance – Stock market reports, commerce, trading, etc. Children’s Progs – Programs for children Social Affairs – Social affairs Religion – Programs concerning religion Phone In – Public expressing their views by Phone Travel & Touring – Holiday- type travel rather than traffic announcements Leisure & Hobby – Leisure interests and hobbies Jazz Music – Jazz Country Music – Country music National Music – Popular music in a language other than English Oldies Music – Popular music from the ‘50s and’ 60s Folk Music – Folk music Documentary – Documentary Alarm Test – Broadcasting when testing emergency broadcast equipment or receivers. Alarm – Alarm!
Using the tuner 08 25 En English Français Español • If you want to listen to the same program type of another station, press the RDS PTY whilst the channel number or station name is flashing. The unit will look for the next station. • If no station can be found, “NOT FOUND” will appear for 4 seconds. Information provided by RDS Each time the RDS DISPLAY is pressed, the display will switch as follows: When tuning in to a station other than an RDS station or to an RDS station which sends weak signal, the display will change in the following order: Using the Auto Station Program Memory (ASPM) Whilst in the ASPM operation mode, the tuner will automatically search for new RDS stations. Up to 30 stations can be stored. If you have already stored some stations in memory, the number of new stations you can store will be less. 1 Press TUNER on the remote control. 2 Press and hold down RDS ASPM on the remote control. After “ASPM” has flashed for about 4 seconds, scanning will start (87.5 MHz to 108 MHz). After scanning, the number of stations stored in memory will be displayed for 4 seconds, and then “END” will appear for 4 seconds. To stop the ASPM operation before it is complete: Press whilst it is scanning for stations. The stations which are already stored in memory will be kept there. Note • If the same station is broadcasting on different frequencies, the strongest frequency will be stored in memory. • Any station which has the same frequency as the one stored in memory will not be stored. • If 30 stations have already been stored in memory, the scan will be aborted. If you want to redo the ASPM operation, erase the preset memory. • If no station have been stored in memory, “END” will appear for about 4 seconds. • If the RDS signals are very weak, station names may not be stored in memory. • The same station name can be stored in different channels. • In a certain area or during certain time periods, the station names may temporarily be different. Notes for RDS operation If any of the following events occur, it does not mean that the unit is faulty: • “PS”, “NO PS” and a station name appear alternately, and properly. • If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly. • When you receive an RDS station whose signal is too weak, information like the station name may not be displayed. • “NO PS”, “NO PTY” or “NO RT” will flash for about 5 seconds, and then the frequency will be displayed. Notes for radio text: • The first 16 characters of the radio text will appear and then they will scroll across the display. • If you tune in to an RDS station which is not broadcasting any radio text, “NO RT” will be displayed when you switch to the radio text position. • Whilst radio text data is received or when the text contents change, “RT” will be displayed. STANDBY/ON CD USB TUNER AUDIO IN DISPLAY FOLDER TUNE+ 1 2 3 4 5 6 7 8 9 0 BT AUDIO CLOCK/TIMER SLEEP EQUALIZER P.BASS BASS/TREBLE RANDOM CLEAR REPEAT OPEN/CLOSE DISPLAY FOLDER MENU PRESET VOLUME ST/MONO ASPM PTY DISPLAY + MUTE TUNE– TUNE+ DIMMER – + – MEMORY /PROGRAM RDS ENTER OPTION Station name (PS) Programme type (PTY) Frequency Radio text (RT) No RDS FM 98.80 MHz
Other connections 09 26 En Chapter 9: Other connections CAUTION • Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. Connecting auxiliary components Connect the front panel AUDIO IN mini-plug jack to your auxiliary playback component. • This method can be used to play music on this unit from iPods/iPhones/iPads that do not support use of an iPod Dock and USB terminal. 1 Press AUDIO IN as the input source. When AUDIO IN is selected “AUDIO IN” will be displayed on the main display. Note • If the AUDIO IN mini-plug jack is connected to auxiliary phones jack, the volume of the unit will be adjusted by the volume on the playback component. If the sound is distorted after you lower the volume of the unit, try lowering the volume on the auxiliary playback component. Connect the rear panel LINE IN audio jacks to your auxiliary playback component. 1 Press AUDIO IN twice as the input source. When LINE is selected “LINE” will be displayed on the main display. STANDBY/ON INPUT VOLUME PHONES AUDIO IN TIMER X-HM21 PHONES AUDIO IN Portable audio player, etc. Stereo mini-plug cable (commercially available) RS LINE IN L R L TV This unit’s rear panel Audio cable (commercially available)
Additional information 10 27 En English Français Español Chapter 10: Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. • If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions. General problem Problem Check Remedy Settings you have made have been cleared. Was the power cord unplugged? When power cord is unplugged, the settings you have made is cleared. Please set the clock again. If you do not want to clear the settings, do not unplug the power cord. Difference in volume between CDs, MP3, WMA, iPod/iPhone/iPad, Tuner, AUDIO IN and LINE. This is not a problem with this unit. The volume may sound differently depending on the input source and recording format. This unit cannot be operated with the remote control. Are you operating from far away? Operate within 7 m, 30º of the remote sensor on the front panel (page 5). Is the remote control sensor exposed to direct sunlight or strong artificial light from a fluorescent bulb, etc.? The remote control signals may not be received properly if the remote control sensor is exposed to direct sunlight or strong artificial light from a fluorescent bulb, etc. Are the batteries dead? Replace the batteries (page 5). Disc cannot be played or disc is ejected automatically. Is the disc scratched? Scratched discs may not play. Is the disc dirty? Wipe the dirt off the disc (page 30). Is this unit placed in a humid location? There could be condensation inside. Wait a while for the condensation to evaporate. Do not place this unit near an air- conditioner, etc. (page 30). Folder or file names are not recognized. (WMA, MP3). Have you exceeded the maximum number of folder or file names this unit can recognize? Up to 255 folders can be recognized on one disc. Up to 999 files can be recognized within one folder. Depending on the folder structure, however, this unit may not be able to recognize certain folders or files. The unit turns off automatically. If no play back and no operation has done for 30 minutes or more, the unit turns off automatically.
Additional information 10 28 En When a USB storage device is connected When an iPod/iPhone/iPad is connected Problem Check Remedy USB storage device is not recognized. Is the USB storage device properly connected? Connect the device securely (all the way in). Is the USB storage device connected via a USB hub? This unit does not support USB hubs. Connect the USB storage device directly. Is the USB storage device supported by this unit? This unit only supports USB mass storage class devices. This unit supports portable flash memory and digital audio playback devices. Only the FAT16 and FAT32 file systems are supported. Other file systems (exFAT, NTFS, HFS etc.) are not supported. USB flash drive that supports USB 2.0 can be used. This device does not support the use of external hard disc drives. This is not a problem with this unit. Turn the power off then back on. Some USB storage devices may not be recognized properly. File cannot be played. Is the file copyright-protected (by DRM)? Copyright-protected files cannot be played. This is not a problem with this unit. Files stored on a computer cannot be played. It may not be possible to play some files. Folder or file names are not displayed or are not properly displayed. Do the folder or file names contain more than 30 characters? The maximum number of characters displayable for the folder and file names is 30. Folder or file names are not displayed in alphabetical order. This is not a problem with this unit. The order in which the folder and file names are displayed depends on the order in which the folders or files were recorded on the USB storage device. Much time is required to recognize the USB storage device. What is the USB storage devices capacity? Some time may be required to load the data when large capacity USB storage devices are connected (this could take several minutes). Power is not supplied to the USB storage device. Is AUTH ERROR displayed on the front panel display? No power is supplied if the power consumption is too high. Turn the power off then back on. Turn the power off, then disconnect and reconnect the USB storage device. Press INPUT to switch to the other input, then switch again to the USB/iPod input. Problem Remedy Can’t operate the iPod/iPhone/iPad by the remote control. Make sure the iPod/iPhone/iPad is connected correctly (refer to Connecting your iPod/iPhone/iPad on page 15). Can’t operate the iPod/iPhone/iPad. Make sure the iPod/iPhone/iPad is connected correctly (refer to Connecting your iPod/iPhone/iPad on page 15). If the iPod/iPhone/iPad is experiencing a hangup, try resetting the iPod/iPhone/iPad, and reconnect it to the unit.
Additional information 10 29 En English Français Español Playable discs and formats • Only the discs that have been finalized can be played. • Discs recorded in packet write mode (UDF format) are not compatible with this unit. • Only discs recorded in ISO9660 Level 1, Level 2 and Joliet can be played. • Files protected by DRM (Digital Rights Management) cannot be played. • Corporation and product names mentioned herein are trademarks or registered trademarks of the respective corporations. Note • This unit does not support multisession discs or multiborder recording. • Multisession/multiborder recording is a method in which data is recorded on a single disc in two or more sessions/borders. A “session” or “border” is one recording unit, consisting of a complete set of data from lead-in to lead-out. Regarding copy protected CDs This unit is designed to conform to the specifications of the audio CD format. This unit does not support the playback or function of discs that do not conform to these specifications. Supported audio file formats • This unit does not support lossless encoding. Cautions on use When moving this unit When moving this unit, be sure to first check that there is no disc loaded and disconnect the iPod/iPhone/iPad. Then press STANDBY/ON, wait for “STAND BY” disappears on main display to turn off, then unplug the power cord. Damage may occur if the unit is transported or moved with a disc inserted, or when another device is connected to the USB terminal or AUDIO IN mini-plug jack. Place of installation • Choose a stable place near the TV or stereo system being used with this unit. • Do not place this unit on top of a TV or color monitor. Also install it away from cassette decks and other devices easily affected by magnetic forces. Avoid the following locations: • Places exposed to direct sunlight • Humid or poorly ventilated places • Extremely hot places • Places exposed to vibrations • Places in which there is much dust or cigarette smoke • Places exposed to soot, steam or heat (kitchens, etc.) Audio CD • Commercially available audio CDs • CD-R/ -RW/ -ROM discs containing music recorded in the CD-DA format WMA WMA files recorded on CD-R/ -RW/ -ROM discs or USB storage devices MP3 MP3 files recorded on CD-R/ -RW/ -ROM discs or USB storage devices
Additional information 10 30 En Do not place objects on this unit Do not place any objects on top of this unit. Do not obstruct the ventilation holes. Do not use this unit on shaggy rugs, beds, sofas, etc., or wrapped in cloth, etc. Doing so will prevent the heat from dispersing, leading to damage. Do not expose to heat. Do not place this unit on top of an amplifier or other component that generates heat. When rack mounting it, to avoid the heat given off by the amplifier or other audio component, place it on a shelf below the amplifier. • Turn off the unit’s power when not using it. • Depending on signal conditions, striped patterns may appear on a TV screen and noise may enter the sound of radio broadcasts when the unit’s power is on. If this happens, turn the unit’s power off. About condensation If this unit is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which this unit is installed rises suddenly due to heater operation, etc., water droplets (condensation) may form inside (on operating parts and the lens). When condensation is present, this unit will not operate properly and playback is not possible. Let this unit stand at room temperature for 1 or 2 hours with the power turned on (the time depends on the extent of condensation). The water droplets will dissipate and playback will become possible. Condensation can also occur in the summer if this unit is directly exposed to the air flow from an air-conditioner. If this happens, move this unit to a different place. Cleaning the product • Unplug the power cord from the power outlet when cleaning this unit. • Clean this unit using a soft cloth. For tough dirt, apply some neutral detergent diluted in 5 to 6 parts water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe again with a soft, dry cloth. • Alcohol, thinner, benzene, insecticides, etc., could cause the print or paint to peel off. Also, leaving rubber or vinyl products in contact with this unit for long periods of time could mar the cabinet. • When using chemical-impregnated wipes, etc., read the cautions included with the wipes carefully. Cleaning the lens • This unit’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer authorized service center. Although lens cleaners for players are commercially available, we advise against using them since some may damage the lens. Handling discs Storing • Always place discs in their cases and store them vertically, avoiding hot, humid places, places exposed to direct sunlight and extremely cold places. • Be sure to read the cautions included with the disc. Cleaning discs • Discs may not play if there are fingerprints or dust on them. In this case, use a cleaning cloth, etc., to gently wipe the disc from the inside towards the outside. Do not use dirty cleaning cloths. • Do not use benzene, thinner or other volatile chemicals. Also do not use record spray or antistatic agents. • For tough dirt, apply some water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe off the moisture with a dry cloth. • Do not use damaged (cracked or warped) discs. • Do not let the signal surface of discs get scratched or dirty. • Do not attach pieces of paper or stickers to discs. Doing so could warp discs, making it impossible to play them. Also note that rental discs often have labels attached to them, and the label’s glue may have oozed out. Check that there is no glue around the edges of such labels before using rented discs. About specially shaped discs Specially shaped discs (heart-shaped, hexagonal, etc.) cannot be played on this unit. Do not attempt to play such discs, as they could damage this unit.
Additional information 10 31 En English Français Español About iPod/iPhone/iPad “Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. iPad, iPhone, iPod, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Restoring all the settings to the defaults Use the steps below to restore the all settings to their defaults. 1 Press STANDBY/ON to turn the power on. 2 Press CD on the remote control or INPUT on the main unit repeatedly to select CD input. 3 Press OPEN/CLOSE to open the disc tray. 4 Press STANDBY/ON while pressing . Use the buttons on this unit’s top panel. “DEFAULT” is displayed while the settings are being restored. Power is turned off.
Additional information 10 32 En Specifications • Amplifier section RMS Power Output: . . . . . . . . . . . . . . . . . . . . . . . 15 W + 15 W (1 kHz, 10 %, T.H.D., 8 ) • Tuner section Frequency Range (FM) . . . . . . . . . . . . . . 87.5 MHz to 108 MHz Antenna Input (FM). . . . . . . . . . . . . . . . . . . . .75 unbalanced Frequency Range (AM). . . . . . . . . . . . . . . 522 kHz to 1620 kHz Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna • Miscellaneous USB terminal (X-HM21) . . . . . . . . . . . . . . . . . . . . . . . 5 V, 2.1 A USB terminal (X-HM11) . . . . . . . . . . . . . . . . . . . . . 5 V, 500 mA Power source. . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz Power consumption Power on (X-HM21). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 W Power on (X-HM11). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 W Power stand-by . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W or less Dimensions . . . . . . . . 215 mm (W) x 95 mm (H) x 315 mm (D) Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg • Speaker (S-HM21) Magnetically shieled speaker system Type 2-way type speaker system 5 cm Tweeter 10 cm Woofer Maximum input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 W Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Dimensions . . . . . 130 mm (W) x 211.5 mm (H) x 240 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg/each • Speaker (S-HM11) Magnetically shieled speaker system Type 2-way type speaker system Piezoelectric Tweeter 10 cm Woofer Maximum input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 W Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Dimensions . . . . . 130 mm (W) x 212 mm (H) x 228.5 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg/each • Accessories Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AAA batteries (R03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AM antenna cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power cord iPad Stand (X-HM21 only) Warranty card Operating instructions (This document) Note • The specifications are applicable when the power supply is 230 V. • Specifications and the design are subject to possible modifications without notice, due to improvements. © 2012 PIONEER CORPORATION. All rights reserved.
Informations supplémentaires 10 33 Fr English Français Deutsch Nederlands Italiano Español Pyccкий
Informazioni aggiuntive 10 33 It English Français Deutsch Nederlands Italiano Español Pyccкий
@M@X|}JHJWXJ iPod/iPhone/iPad (^@[@ X-HM21) 05 15 Ru English Français Deutsch Nederlands Italiano Español Pyccкий ¤[V}V 5: @M@X|}JHJWXJ iPod/iPhone/iPad (^@[@ X-HM21) H0+B8+9 4+-B+9-1;9;19 iPod/iPhone/iPad 5 -);;+26 6B80+CB8@6 4+3@+(:98 40+B(6O1@)8? @>B+5+5)F9B8@9;;>C 3@65 B iPod/iPhone/iPad. P)B80+C5) @+B40+13@9-9;1: 263>51 -(: iPod/iPhone/iPad 2+E98 @>4+(;:8?B: B -);;+*+ )44)0)8) 1(1 B)2+*+ 6B80+CB8@) iPod/iPhone/iPad. Y@H^}JMOHJWXJ @HHJMOX \@HJ[J iPod/iPhone/iPad P1E9 401@9-9;> 2+-9(1 iPod/iPhone/iPad, 5+8+0>9 2+*68 @+B40+13@+-18?B: ;) -);;+2 6B80+CB8@9. YMX\JZVWXJ • J+24);1: Pioneer ;9 *)0);810698 @+B40+13@9-9;19 -);;+C B1B892+C -06*1I 2+-9(9C iPod/iPhone/iPad, 50+29 65)3);;>I. • P95+8+0>9 V6;5G11 2+*68 =>8? +*0);1F9;> @ 3)@1B12+B81 +8 1B4+(?3692+C 2+-9(1 1(1 @90B11 40+*0)22;+*+ +=9B49F9;1:. • KB80+CB8@) iPod/iPhone/iPad (1G9;3106D8B: -(: 5+410+@);1: 2)8901)(+@, ;9 3)A1A9;;>I )@8+0B512 40)@+2, 1 2)8901)(+@, 5+410+@);19 5+8+0>I 4+(?3+@)89(D D01-1F9B51 0)309O9;+. • [)519 V6;5G11, 5)5 75@)()C390, ;9 2+*68 5+;80+(10+@)8?B: B 4+2+A?D -);;+C B1B892>, 4+78+26 4909- @>4+(;9;192 4+-5(DF9;1: 095+29;-698B: +85(DF)8? 75@)()C390. • J+24);1: Pioneer ;9 2+E98 ;1 401 5)51I +=B8+:89(?B8@)I ;9B81 +8@98B8@9;;+B8? 3) 5)5+C-(1=+ 40:2+C 1(1 5+B@9;;>C 6A90=, 401F1;9;;>C ;9-+B8)85)21 1(1 4+8909C 3)41B);;>I 2)8901)(+@ @ 0936(?8)89 B=+: @ 0)=+89 iPod/iPhone/iPad. • M(: 4+(6F9;1: 4+-0+=;>I 1;B8065G1C +8;+B189(?;+ 1B4+(?3+@);1: iPod/iPhone/iPad +=0)A)C89B? 5 065+@+-B8@6, 401()*)92+26 5 iPod/iPhone/iPad. • T8) B1B892) =>() 0)30)=+8);) 1 40+89B810+@);) -(: @90B11 40+*0)22;+*+ +=9B49F9;1: iPod/iPhone/iPad, 65)3);;+C ;) @9=-B)C89 Pioneer (http://pioneer.jp/homeav/support/ios/eu/). • KB8);+@5) ;) @)O iPod/iPhone/iPad @90B1C 40+*0)22;+*+ +=9B49F9;1:, +8(1F;>I +8 65)3);;>I ;) @9=-B)C89 Pioneer, 2+E98 =>8? ;96-)F;+C 13-3) ;9B+@29B812+B81 B -);;+C B1B892+C. • M);;+9 6B80+CB8@+ ;9 2+E98 1B4+(?3+@)8?B: -(: 3)41B1 -);;>I B CD, 8D;90) 1(1 -06*+*+ 5+;89;8) ;) iPod/ iPhone/iPad. Y@H[ZJWXJ iPod/iPhone/iPad Y@H[ZJWXJ iPod/iPhone/iPad X@[|@}VWXJ\ MX[VVJ\@ @H^V}X 1 Y@H@JHXWX^J V]J[ iPod/iPhone/iPad ^M@^}. 2 YM@^X^J V]J[ iPod/iPhone/iPad ZJMJ| WXOW ZV^ ^@X X @H@JHXWX^J J@ iPod/iPhone/iPad. iPod/iPhone/iPad V|©J\ USB (^@[@ VHX@) iPod nano 3G/4G/5G/6G/7G iPod touch 1G/2G/3G/4G/5G iPhone 5 iPhone 4S iPhone 4 iPhone 3GS iPhone 3G iPhone iPad mini iPad (4-J @@[JWXJ) iPad (3-J @@[JWXJ) iPad 2 iPad
@M@X|}JHJWXJ iPod/iPhone/iPad (^@[@ X-HM21) 05 16 Ru 3 ^VW@}X^J iPod/iPhone/iPad WV @H^V}J. @M@X|}JHJWXJ iPod/iPhone/iPad 1 Y@H[ZJWXJ iPod/iPhone/iPad. • ^B(1 iPod/iPhone/iPad 4+-5(DF)98B:, 5+*-) -);;>C )44)0)8 @5(DF9;, @+B40+13@9-9;19 iPod/iPhone/iPad ;9 ;)F;98B:. 2 {VO\X^J USB H[~ }`]@MV } VZJ^}J }¥@HW@@ X^@ZWXV. P) +B;+@;+2 -1B4(99 4+5)3>@)98B: 1;-15)G1: «USB/iPod». 3 Y@[J |V}JMJWX~ MV@|WV}VWX~ V}^@\V^XZJX WVZWJ^~ }@M@X|}JHJWXJ. • L29DA19B: ;) -);;+2 )44)0)89 +0*);> 640)@(9;1: @+B40+13@9-9;192 iPod/iPhone/iPad - 78+ /, , . • U B(9-6DA92 B(6F)9 640)@(:C89 iPod/iPhone/iPad ;94+B09-B8@9;;+: - H+1B5 V)C() 4+ 129;1 1B4+(;189(: 1(1 E);06. - U+B40+13@9-9;19 @ 09E129 4+@8+0) 1(1 B(6F)C;+C 4+B(9-+@)89(?;+B81. YY { • J+*-) iPod/iPhone/iPad 4+-B+9-1;9; 5 -);;+26 6B80+CB8@6, 9B(1 @> E9()989 640)@(:8? ;94+B09-B8@9;;+ iPod/iPhone/iPad, ;)-9E;+ 6-90E1@)C89 iPod/iPhone/iPad -06*+C 065+C, F8+=> 409-+8@0)818? B=+1 @ 0)=+89, 5+8+0>9 2+*68 @+3;15;68? 13-3) 4(+I+*+ 5+;8)58). YMX\JZVWXJ • M(: 4+(6F9;1: 4+-0+=;>I 1;B8065G1C +8;+B189(?;+ 1B4+(?3+@);1: iPod/iPhone/iPad +=0)A)C89B? 5 065+@+-B8@6, 401()*)92+26 5 iPod/iPhone/iPad. • H+-3)0:-5) iPod/iPhone/iPad @>4+(;:98B: @B9*-), 5+*-) iPod/iPhone/iPad 4+-B+9-1;9; 5 -);;+26 6B80+CB8@6. (M);;): V6;5G1: 4+--90E1@)98B: 8)5E9 @ 09E129 +E1-);1:.) • ^B(1 @I+- 49095(DF)98B: B USB/iPod ;) -06*6D V6;5G1D, @+B40+13@9-9;19 iPod/iPhone/iPad @0929;;+ +B8);)@(1@)98B:. £ { ^B(1 -);;+9 6B80+CB8@+ ;9 2+E98 @+B40+13@9B81 iPod/iPhone/ iPad, @>4+(;189 B(9-6DA19 40+@9051 -(: 4+1B5) 1 6B80);9;1: ;94+()-+5: • H0+@90?89, 4+--90E1@)98B: (1 4+-B+9-1;9;;>C iPod/ iPhone/iPad -);;>2 6B80+CB8@+2. • H9094+-B+9-1;189 iPod/iPhone/iPad 5 6B80+CB8@6. H9093)46B8189 iPod/iPhone/iPad, 9B(1 78+ ;9 B0)=)8>@)98. • H0+@90?89, 4+--90E1@)98B: (1 40+*0)22;+9 +=9B49F9;19 iPod/iPhone/iPad -);;>2 )44)0)8+2. ^B(1 ;98 @+32+E;+B81 640)@(:8? iPod/iPhone/iPad, 40+@90?89 B(9-6DA19 4)0)2980>: • H0)@1(?;+ (1 4+-5(DF9; iPod/iPhone/iPad? H9094+-B+9-1;189 iPod/iPhone/iPad 5 6B80+CB8@6. • P9 3)@1B (1 iPod/iPhone/iPad? H+40+=6C89 @>4+(;18? B=0+B ;)B80+95 iPod/iPhone/iPad 1 49094+-B+9-1;189 iPod/iPhone/iPad 5 6B80+CB8@6.
(CD
@[|@}VWXJ ^WJMV 08 24 Ru • H+@8+0189 O)*1 1 -+ 4, F8+=> ;)B80+18? -06*19 B8);G11 1(1 B29;18? 409-6B8);+@(9;;6D B8);G1D. H01 B+I0);9;11 ;+@+C B8);G11 @ 4)2:81 =6-98 B810)8?B: B8);G1:, 409-@)0189(?;+ 3);9B9;;): @ 4)2:8? -(: 78+*+ ;+290) 3)40+*0)2210+@);;+*+ 5);)(). YMX\JZVWXJ • H01 )@)01C;+2 +85(DF9;11 418);1: 1(1 +8B+9-1;9;11 5)=9(: 418);1: 490929;;+*+ 8+5) V6;5G1: 09390@10+@);1: 3)A1818 3);9B9;;>9 @ 4)2:8? B8);G11 ;) ;9B5+(?5+ F)B+@. [~ }`|@}V |VWJJWW@ } V\~^ ^VWXX 1 {VO\X^J W@ PRESET +/–, Z^@]` }`]MV^ OJ[VJ\ ^VWX. [~ VWXM@}VWX~ MJH^VW@}[JWW`¥ ^VWX X8);G11, B+I0);9;;>9 @ 4)2:81, 2+*68 B5);10+@)8?B: )@8+2)81F9B51. (X5);10+@);19 409-6B8);+@(9;;+C 4)2:81) 1 {VO\X^J X HJMOX}V^J W@ PRESET +/–. Q8+=0)318B: 3)40+*0)2210+@);;>C ;+290, 1 3)40+*0)2210+@);;>9 B8);G11 =6-68 ;)B80)1@)8?B: 4+B(9-+@)89(?;+, ;) 5 B956;- 5)E-):. 2 Y@}^@MW@ WVO\X^J W@ PRESET +/– MX @]WVMOJWXX OJ[VJ\@ ^VWXX. [~ @[W@@ ^XMVWX~ MJH^VW@}[JWW@ V\~^X 1 {VO\X^J TUNER WV [^J HX^VWX@WW@@ MV}[JWX~. 2 {VO\X^J W@ CLEAR, @V WJ @~}X^~ XWHXVX~ «MEMORY CLEAR». YMX\JZVWXJ • UB9 B8);G11 =6-68 B8908>. @[|@}VWXJ X^J\` MVHX@HVWW`¥ (RDS) WV@\^}@ X^J\@ RDS X1B892) 0)-1+-);;>I (RDS) – 78+ B1B892), 5+8+0): 1B4+(?3698B: =+(?O1;B8@+2 0)-1+B8);G1C @ -1)4)3+;9 FM -(: 409-+B8)@(9;1: B(6O)89(:2 0)3(1F;+C 1;V+02)G11 – ;)401290, ;)3@);1: 0)-1+B8);G11 1(1 80);B(10692+C 40+*0)22>. Q-;+C 13 V6;5G1C B1B892> RDS :@(:98B: @+32+E;+B8? 4+1B5) B8);G11, 80);B(106DA9C 809=692>C 814 40+*0)22>. P)401290, 2+E;+ +B6A9B8@(:8? 4+1B5 B8);G11, 5+8+0): 80);B(10698 40+*0)22> @ E);09 JAZZ (-E)3). Y+E;+ @9B81 4+1B5 40+*0)22 B(9-6DA1I 814+@: Y@X M@MV\\ X^J\` MVHX@HVWW`¥ RDS Y+E;+ +B6A9B8@18? 4+1B5 814+@ 40+*0)22, 4909F1B(9;;>I @>O9. 1 {VO\X^J TUNER WV [^J HX^VWX@WW@@ MV}[JWX~. • X1B892) RDS -+B864;) 8+(?5+ @ -1)4)3+;9 FM. 2 {VO\X^J RDS PTY WV [^J HX^VWX@WW@@ MV}[JWX~. L;-15)G1: «SELECT» 4+:@18B: 401290;+ ;) 6 B956;-. 3 {VO\X^J HI H[~ }`]@MV ^XV M@MV\\`, @^@M ¥@^X^J M@[V^. H01 5)E-+2 ;)E)811 5;+451 =6-98 4+5)3>@)8?B: 814 40+*0)22>. ^B(1 5;+45) 6-90E1@)98B:, 814 40+*0)22> =6-98 4+5)3>@)8?B: ;94090>@;+. 4 @ }MJ\~ @^@]MVOJWX~ }`]MVWW@@ ^XV M@MV\\` (} ^JZJWXJ 6 JWH), @}^@MW@ WVO\X^J W@ RDS PTY. H+B(9 3)*+0);1: @ 89F9;19 2 B956;- @>=0);;+*+ 814) 40+*0)22>, 4+:@18B: 1;-15)G1: «SEARCH», 1 ;)F;98B: +490)G1: 4+1B5). News – ;+@+B81 Current Affairs – 8956A19 B+=>81: Information – 1;V+02)G1: Sport – B4+08 Education – o=0)3+@)89(?;): 1;V+02)G1 Drama – p)-1+B4958)5(1 1 8.-. Cultures – ;)G1+;)(?;): 1 29B8;): 56(?860;): E13;?, 89)80 1 8.-. Science – ;)65) 1 89I;15) Varied Speech – 40+*0)22>, 4+B80+9;;>9 ;) =9B9-9 1(1 +=A9;11, ;)401290 @158+01;> 1(1 1;890@?D. Pop Music – 4+4-263>5) Rock Music – 0+5-263>5) Easy Listening – (9*5): 263>5) Light Classics M – (9*5): 5()BB1F9B5): 263>5) Serious Classics – c90?93;): 5()BB1F9B5): 263>5) Other Music – 263>5), ;9 B++8@98B8@6DA): 4909F1B(9;;>2 5)89*+01:2 Weather & Metr – B@+-51 1 40+*;+3> 4+*+-> Finance – =10E9@>9 B@+-51, 5+2290F9B5):, 8+0*+@): 1;V+02)G1: 1 8.-. Children’s Progs – H0+*0)22> -(: -989C Social Affairs – +=A9B8@9;;): E13;? Religion – 40+*0)22> + 09(1*11 Phone In – 40+*0)22>, 409-6B2)801@)DA19 +=B6E-9;19 5)5+C-(1=+ 892> 1 +=A9;19 B+ B(6O)89(:21 4+ 89(9V+;6 Travel & Touring – 4689O9B8@1: 1 +8->I Leisure & Hobby – B@+=+-;+9 @092:, 1;8909B> 1 I+==1 Jazz Music – -E)3+@): 263>5) Country Music – 263>5) «5);801» National Music – 4+46(:0;): 263>5) ;9 ;) );*(1CB5+2 :3>59 Oldies Music – 4+46(:0;): 263>5) 1950-I 1 1960-I *+-+@ Folk Music – ;)0+-;): 263>5) Documentary – 46=(1G1B81F9B519 40+*0)22> Alarm Test – 80);B(:G1: 401 89B810+@);11 )@)01C;+*+ @9A)89(?;+*+ +=+06-+@);1: 1(1 40192;>I 6B80+CB8@. Alarm – 809@+*)!
iPod/iPhone/iPad ;) B80. 15). P9 0)=+8)98 iPod/iPhone/iPad. K=9-189B?, F8+ iPod/iPhone/iPad 4+-5(DF9; 40)@1(?;+ (B2.
iPod/iPhone/iPad ;) B80. 15). ^B(1 iPod/iPhone/iPad «3)@1B», 4+40+=6C89 @>4+(;18? B=0+B ;)B80+95 iPod/iPhone/iPad 1 49094+-B+9-1;189 9*+ 5 6B80+CB8@6.
@@[WX^J[WV~ XW@M\VX~ 10 29 Ru English Français Deutsch Nederlands Italiano Español Pyccкий @M@X|}@HX\`J HXX X @M\V^` • ¢@^ }@M@X|}@HX^~ ^@[@ XWV[X|XM@}VWW`J HXX. • M1B51, 3)41B);;>9 @ 09E129 4)598;+C 3)41B1 (V+02)8 UDF), ;9B+@29B812> B -);;>2 6B80+CB8@+2. • Y+*68 @+B40+13@+-18?B: 8+(?5+ -1B51, 3)41B);;>9 @ V+02)89 ISO9660 Level 1, Level 2 1 Joliet. • R)C(>, 3)A1A9;;>9 B1B892+C DRM (Digital Rights Management), @+B40+13@+-18?B: ;9 2+*68. • P)3@);1: 5+04+0)G1C 1 13-9(1C, 64+2:;68>9 @ -);;+2 -+5629;89, :@(:D8B: 8+0*+@>21 2)05)21 1(1 3)09*1B8010+@);;>21 8+0*+@>21 2)05)21 B++8@98B8@6DA1I 5+04+0)G1C. YMX\JZVWXJ • M);;+9 6B80+CB8@+ ;9 4+--90E1@)98 2;+*+B9);B+@>9 -1B51 1(1 2;+*+50)8;6D 4+B(9-+@)89(?;6D (multi- border) 3)41B?. • Y;+*+B9);B+@):/2;+*+50)8;): 4+B(9-+@)89(?;): 3)41B? — 78+ 298+-, 401 5+8+0+2 -);;>9 3)41B>@)D8B: ;) +-1; 1 8+8 E9 -1B5 @ -@) 1(1 =+(99 B9);B)/B9BB11. «X9);B» 1(1 «B9BB1:» 409-B8)@(:98 B+=+C 9-1;1G6 3)41B1, B+B8+:A6D 13 4+(;+*+ ;)=+0) -);;>I +8 ;)F)(?;+C 3)41B1 -+ 5+;9F;+C 3)41B1. ^W@X^J[W@ @\V^-HX@} |V¬X^@ @^ @XM@}VWX~ M);;+9 6B80+CB8@+ B5+;B80610+@);+ @ B++8@98B8@11 B+ B49G1V15)G1:21 V+02)8) 3@65+@>I 5+24)58--1B5+@ (Audio CD). M);;+9 6B80+CB8@+ ;9 4+--90E1@)98 @+B40+13@9-9;19 1(1 0)=+86 -1B5+@, ;9 B++8@98B8@6DA1I 7812 B49G1V15)G1:2. Y@HHJMOX}VJ\`J @M\V^` VHX@V[@} • M);;+9 6B80+CB8@+ ;9 4+--90E1@)98 5+-10+@);19 =93 4+890?. ¢JM` MJH@^@M@OW@^X MX ²[V^VXX YMX JMJ\J¬JWXX ^M@^}V H01 490929A9;11 6B80+CB8@) B;)F)() +=:3)89(?;+ 6=9-189B? @ 8+2, F8+ ;9 3)*06E9; -1B5, 1 +8B+9-1;189 iPod/iPhone. W)892 ;)E2189 5;+456 STANDBY/ON, -+E-189B?, 5+*-) ;) +B;+@;+2 -1B4(99 1BF93;98 1;-15)G1: «STAND BY», 3)892 +8B+9-1;189 5)=9(? 418);1:. ^B(1 )44)0)8 80);B4+0810698B: 1(1 490929A)98B: B+ @B8)@(9;;>2 -1B5+2 1(1 1;>2 6B80+CB8@+2, 4+-5(DF9;;>2 5 0)3]926 USB 1(1 5 21;1- 0)3]926 AUDIO IN. ¢J^@ ^VW@}X • U>=90189 6B8+CF1@+9 29B8+ @+3(9 89(9@13+0) 1(1 B8909+V+;1F9B5+C B1B892>, 5+8+0>9 1B4+(?36D8B: B+@29B8;+ B -);;>2 6B80+CB8@+2. • P9 0)329A)C89 -);;+9 6B80+CB8@+ B@90I6 ;) 89(9@13+09 1(1 G@98;+2 2+;18+09. [)5E9 6B8);)@(1@)C89 09B1@90 -)(?O9 +8 5)BB98;>I 2)*;18+V+;+@ 1 1;>I 6B80+CB8@, ;) 5+8+0>9 2+E98 4+@(1:8? 2)*;18;+9 4+(9. |]JV^J [JH¬X¥ \J^: • Y9B8), 4+-@90*)92>9 40:2+26 B+(;9F;+26 B@986 • X>0>9 1(1 4(+I+ @9;81(10692>9 29B8) • Y9B8) B+ B(1O5+2 @>B+5+C 892490)860+C • Y9B8), 4+-@90*)92>9 @1=0)G1:2 • Y9B8) B =+(?O12 B+-90E);192 4>(1 1(1 B1*)098;+*+ ->2) • Y9B8), 4+-@90*)92>9 @+3-9CB8@1D B)E1, 4)0) 1(1 894() (56I;1 1 8.4.) {J MV|\J¬V^J MJH\J^` WV ^M@^}J P9 0)329A)C89 5)519-(1=+ 409-298> ;) 6B80+CB8@9 B@90I6. {J |VM`}V^J }JW^X[~X@WW`J @^}JM^X~. P9 1B4+(?36C89 -);;+9 6B80+CB8@+ ;) @+0B1B8>I 5+@0)I, 50+@)8:I, -1@);)I 1 8. -. 1(1 3)@90;68>2 @ 85);? 1 8. -. T8+ 2+E98 4+29O)8? 0)BB91@);1D 894(), F8+ 2+E98 401@9B81 5 4+(+259. {J @H}JMV^J MJX}JM }@|HJ^}X ^J[V. P9 0)329A)C89 6B80+CB8@+ B@90I6 ;) 6B1(189(9 1(1 -06*+2 5+24+;9;89, *9;90106DA92 894(+. H01 6B8);+@59 @ B8+C56, F8+=> 13=9E)8? @+3-9CB8@1: 894(), +8@+-12+*+ +8 6B1(189(: 1(1 1;+*+ )6-1+5+24+;9;8), 6B8);)@(1@)C89 09B1@90 ;) 4+(56 ;1E9 6B1(189(:. Audio CD • L29DA19B: @ 40+-)E9 3@65+@>9 5+24)58--1B51 (Audio CD) • M1B51 CD-R/ -RW/ -ROM B 263>5+C, 3)41B);;+C @ V+02)89 CD-DA WMA R)C(> WMA, 3)41B);;>9 ;) -1B51 CD-R/ -RW/ -ROM 1(1 3)4+21;)DA19 6B80+CB8@) USB MP3 R)C(> MP3, 3)41B);;>9 ;) -1B51 CD-R/ -RW/ -ROM 1(1 3)4+21;)DA19 6B80+CB8@) USB
@@[WX^J[WV~ XW@M\VX~ 10 31 Ru English Français Deutsch Nederlands Italiano Español Pyccкий HXV¥ JXV[W@ @M\` M1B51 +B+=+C V+02> (@ @1-9 B90-G), O9B816*+(?;15) 1 8. 4.) ;9 2+*68 @+B40+13@+-18?B: ;) -);;+2 6B80+CB8@9. P9 4>8)C89B? @+B40+13@9B81 8)519 -1B51, 8)5 5)5 +;1 2+*68 4+@09-18? -);;+9 6B80+CB8@+. iPod/iPhone/iPad “Made for iPod,” “Made for iPhone” 1 “Made for iPad” +3;)F)98, F8+ 7(9580+;;>C 401=+0 =>0 0)30)=+8); B G9(?D 4+-5(DF9;1: +409-9(9;;+ 5 iPod, iPhone 1(1 iPad B++8@98B8@9;;+, 1 12998B: B9081V1G15)G1: 0)30)=+8F15) + B++8@98B8@11 B 89I;1F9B5121 I)0)58901B815)21 Apple. Apple ;9 ;9B98 +8@98B8@9;;+B81 3) +=9B49F9;19 0)=+86 -);;+*+ 6B80+CB8@) 1(1 9*+ B++8@98B8@1: B+ B8);-)08)21 4+ 89I;159 =93+4)B;+B81 1(1 09*6(:81@;>21 ;+02)21. H+E)(6CB8), +=0)8189 @;12);19, F8+ 1B4+(?3+@);19 -);;+*+ 401=+0) B iPod, iPhone 1(1 iPad 2+E98 +801G)89(?;+ B5)3>@)8?B: ;) 5)F9B8@9 =9B40+@+-;+C B@:31. iPad, iPhone, iPod, iPod nano
Apple Inc.,
@@[WX^J[WV~ XW@M\VX~ 10 33 Ru English Français Deutsch Nederlands Italiano Español Pyccкий
Have a question about the Pioneer X-HM11-K but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer X-HM11-K. Please make sure that you describe your difficulty with the Pioneer X-HM11-K as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.
There are no questions about the Pioneer X-HM11-K yet.