Pioneer X-CM31-K manual

View a manual of the Pioneer X-CM31-K below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Hi-Fi system
  • Model/name: X-CM31-K
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Russian

Table of Contents

Page: 1
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light) D3-4-2-1-7c*_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 25 cm at top, 15 cm at rear, and 5 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period. K041_A1_En
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007.
CLASS 1 LASER PRODUCT
D58-5-2-2a_A1_En
X-CM31_SYXE8_En.book 2 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 2 2012/7/5 10:44:07
Page: 2
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
plug can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation). D3-4-2-2-2a*_A1_En
Information for users on collection and disposal of old equipment and used batteries
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Symbol examples
for batteries
Symbol for
equipment
Pb
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation). D3-4-2-2-1a_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
X-CM31_SYXE8_En.book 3 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 3 2012/7/5 10:44:07
Page: 3
4
En
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you
have finished reading the instructions, put them in a safe place for future reference.
Contents
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Loading the batteries in the remote control . . . . . . . . . 5
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . 5
02 Part names and functions
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . . . 7
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Top panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
03 Connections
Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . . 11
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
04 Getting started
To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Input function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Display brightness control . . . . . . . . . . . . . . . . . . . . . . . 12
Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Muting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Equaliser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
P.bass control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . 13
Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . 14
Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . . . 14
Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
05 iPod/iPhone/iPad playback
Confirming what iPod/iPhone/iPad models are
supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . 15
Connecting iPod/iPhone to the top panel . . . . . . . . . . . 15
Connecting iPad using supplied stand . . . . . . . . . . . . . 16
Watching iPod/iPhone videos on your TV . . . . . . . . . . . 16
Playing iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Playing iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
06 Disc playback
Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Advanced CD or MP3/WMA disc playback . . . . . . . . . 19
Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Programmed play (CD or MP3/WMA) . . . . . . . . . . . . . . 20
About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . 20
About folder playback order . . . . . . . . . . . . . . . . . . . . . . 20
Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 21
Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 21
07 USB playback
Playing USB storage devices . . . . . . . . . . . . . . . . . . . . 22
Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 23
Playing in the desired order
(Programmed Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
08 Using the tuner
Listening to the radio broadcasts . . . . . . . . . . . . . . . . 24
Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
To recall a memorised station . . . . . . . . . . . . . . . . . . . . 25
To scan the preset stations. . . . . . . . . . . . . . . . . . . . . . . 25
To erase entire preset memory. . . . . . . . . . . . . . . . . . . . 25
Using the Radio Data System (RDS) . . . . . . . . . . . . . . 25
An introduction to RDS. . . . . . . . . . . . . . . . . . . . . . . . . . 25
Searching for RDS programs. . . . . . . . . . . . . . . . . . . . . 25
Information provided by RDS . . . . . . . . . . . . . . . . . . . . . 26
Using the Auto Station program Memory (ASPM). . . . 26
Notes for RDS operation. . . . . . . . . . . . . . . . . . . . . . . . . 26
09 Other connections
Connecting auxiliary components . . . . . . . . . . . . . . . . 27
10 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Playable discs and formats . . . . . . . . . . . . . . . . . . . . . 30
Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . 30
Supported audio file formats . . . . . . . . . . . . . . . . . . . . . 30
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Do not place objects on this unit . . . . . . . . . . . . . . . . . . 31
About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning the lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
About specially shaped discs. . . . . . . . . . . . . . . . . . . . . 31
About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . 32
Restoring all the settings to the defaults . . . . . . . . . . 32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
X-CM31_SYXE8_En.book 4 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 4 2012/7/5 10:44:07
Page: 4
Before you start 01
5
En
English
Français
Español
Chapter 1:
Before you start
What’s in the box
Please confirm that the following accessories are in the box
when you open it.
• Remote Control
• Power cord
• AM antenna cable
• FM wire antenna
• AAA batteries (R03) x 2
• Non-skid pads x 8
• iPad stand
• Warranty card
• Operating instructions (this document)
Loading the batteries in the
remote control
1 Open the rear lid and load the batteries as
illustrated below.
2 Close the rear lid.
CAUTION
• Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
• When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks ( and ).
• Do not heat batteries, disassemble them, or throw them
into flames or water.
• Batteries may have different voltages, even if they are the
same size and shape. Do not use different types of
batteries together.
• To prevent leakage of battery fluid, remove the batteries
if you do not plan to use the remote control for a long
period of time (1 month or more). If the fluid should leak,
wipe it carefully off the inside of the case, then insert
new batteries. If a battery should leak and the fluid
should get on your skin, flush it off with large quantities
of water.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
• WARNING
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Using the remote control
The remote has a range of about 7 m at an angle of about 30º
from the remote sensor.
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote.
STANDB
Y/ON


iPod
CD
USB
TUNER
AUDIO
IN/LINE
DISPLAY
FOLDER
MENU
PRESET
VOLUME
ST/MONO
ASPM
PTY
DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER






–
+
–
MEMORY
/PROGRA
M
1
2
3
4
5
6
7
8
9
0
TV
OUT
CLOCK/TIME
R
SLEEP
EQULIZE
R
P.BASS
BASS/TRE
BLE
RANDOM
CLEAR
REPEAT
OPEN/CL
OSE
RDS
ENTER
30°
7 m
30°
X-CM31_SYXE8_En.book 5 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 5 2012/7/5 10:44:08
Page: 5
Part names and functions
02
6
En
Chapter 2:
Part names and functions
Remote control
1  STANDBY/ON
Switches the receiver between standby and on (page 18).
2 Input function buttons
Use to select the input source to this receiver (page 18).
3 CD Receiver control buttons
TV OUT
Setting iPod/iPhone video on/off.
CLOCK/TIMER
Use for setting the clock, as well as for setting and
checking the timers (page 12).
SLEEP
See Using the sleep timer on page 14.
4 Numeric buttons (0 to 9)
Use to enter the number (page 19).
5 CLEAR
Use to clear the programmed play (page 20).
6 CD Receiver control buttons
DISPLAY
Press to change the display for songs playing back from
CD or USB (page 21).
FOLDER
Use to select the folder of the MP3/WMA disc or USB
mass storage device (page 20).
MENU
Use to access the menu.
MEMORY/PROGRAM
Use to memory or program the MP3/WMA disc
(page 20).
7 /// (TUNE +/–), ENTER
Use to select/switch system settings and modes, and to
confirm actions.
Use TUNE +/– can be used to find radio frequencies
(page 24).
8 PRESET control buttons
Use to select preset radio stations (page 24).
9 MUTE
Mutes/unmutes the sound (page 12).
10 Playback control buttons
Use to control each function after you have selected it using
the input function buttons (page 18).
4
5
1
3
2
6
7
8
12
17
13
14
9
10
11
16
15
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
DISPLAY FOLDER
MENU
PRESET VOLUME
ST/MONO ASPM PTY DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
   
 
–
+
–
MEMORY
/PROGRAM
1 2 3
4 5 6
7 8 9
0
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR REPEAT
OPEN/CLOSE
RDS
ENTER
X-CM31_SYXE8_En.book 6 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 6 2012/7/5 10:44:08
Page: 6
Part names and functions 02
7
En
English
Français
Español
11 Tuner control buttons
ST/MONO
Use to switch the sound mode between stereo and
monaural. (page 24)
RDS ASPM
Use to search for RDS Auto station program memory
(page 25).
RDS PTY
Use to search for RDS program types (page 25).
RDS DISPLAY
Press to change the RDS display for information mode
(page 25).
12 OPEN/CLOSE
Use to open or close the disc tray (page 18).
13 Sound control buttons
Adjust the sound quality (page 13).
14 RANDOM
Press to randomize order play setting from a CD, iPod or USB
(page 19).
15 REPEAT
Press to change the repeat play setting from a CD, iPod or
USB (page 19).
16 Volume control buttons
Use to set the listening volume (page 12).
17 DIMMER
Dims or brightens the display. The brightness can be
controlled in four steps (page 12).
Speaker system
Important
Speaker grille cannot be removed.
Attaching the Non-skid pads
Apply the accessory non-skid pads to the bottom surfaces of
the speakers.
Important
Use the speaker is usually in an upright position.
3
2
1
1 Tweeter
2 Woofer
3 Bass Reflex Duct
X-CM31_SYXE8_En.book 7 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 7 2012/7/5 10:44:08
Page: 7
Part names and functions
02
8
En
Front panel
1 Main display
2 Volume control
Use to set the listening volume (page 12).
3 Volume illumination
Light when the power on.
4 Headphone socket
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers.
5 AUDIO IN socket
Use to connect an auxiliary component using a stereo
minijack cable (page 27).
6 Remote sensor
Receives the signals from the remote control.
7 Disc tray
Place the disc, label side up (page 18).
8 TIMER indicator
Lights when the receiver is power off with timer setting.
9 USB terminal
Use to connect your USB mass storage device or Apple iPod/
iPhone/iPad as an audio source (page 22).
TIMER VOLUME
PHONES AUDIO IN iPad
4 5 6 7 8 9
2 3
1
X-CM31_SYXE8_En.book 8 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 8 2012/7/5 10:44:08
Page: 8
Part names and functions 02
9
En
English
Français
Español
Top panel
1 iPod/iPhone connector port
To connect the iPod/iPhone, press the PUSH OPEN tab
(page 15).
2  STANDBY/ON
Switches the receiver between standby and on (page 18).
3 Playback control buttons
Selects the desired track or file to be played back. Use to stop
the playback. Stops playback or resumes playback from the
pause point.
4 INPUT
Selects the input source.
5 Disc tray open/close button
Use to open or close the disc tray (page 18).
STANDBY/ON 
    INPUT 
PUSH OPEN
2 5
1
3 4
X-CM31_SYXE8_En.book 9 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 9 2012/7/5 10:44:08
Page: 9
Connections
03
10
En
Chapter 3:
Connections
CAUTION
• Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
• Connect the power cord after all the connections
between devices have been completed.
Speaker connection
To connect the speaker cord to the connector, insert into the
speaker connector of the rear of the receiver.
CAUTION
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Do not connect any speakers other than those supplied
to this system.
• Do not connect the supplied speakers to any amplifier
other than the one supplied with this system.
Connection to any other amplifier may result in
malfunction or fire.
• Do not attach these speakers to the wall or ceiling. They
may fall off and cause injury.
• These speakers are magnetically shielded. However,
depending on the installation location, color distortion
may occur if the speaker system is installed extremely
close to the screen of a television set. If this happens,
turn off the television set, and then turn it on after 15 to
30 minutes. If the problem persists, move the speaker
system away from the television set.
Connecting a TV
• When an iPod/iPhone is connected to this unit, the TV
output setting of iPod/iPhone is automatically set to
‘ON’.
Note
• Some iPod allow the TV output setting to be changed
while connected.
• When the iPod/iPhone is disconnected from this unit,
the iPod/iPhone’s TV output setting returns to its original
state.
AM
LOOP
ANTENNA VIDEO LINE
AC IN
OUT IN
SPEAKERS
L
R
R L
FM
UNBAL 75 Ω
Left
speaker
Right
speaker
This unit’s rear panel
VIDEO LINE
AC IN
OUT IN
SPEAKERS
L
R
R L
Yellow
TV
Video cable
(commercially available)
To video input
terminal
This unit’s rear panel
X-CM31_SYXE8_En.book 10 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 10 2012/7/5 10:44:08
Page: 10
Connections 03
11
En
English
Français
Español
Connecting antennas
Connect the AM loop antenna and the FM wire antenna as
shown below. To improve reception and sound quality,
connect external antennas (see Using external antennas
below).
1 Connect the AM antenna wires.
Holding the connector to connect.
2 Fix the AM loop antenna to the attached
stand.
To fix the stand to the antenna, bend in the direction indicated
by the arrow (fig. a) then clip the loop onto the stand (fig. b).
3 Place the AM antenna on a flat surface and
in a direction giving the best reception.
4 Connect the FM wire antenna into the FM
antenna socket.
For best results, extend the FM antenna fully and fix to a wall
or door frame. Don’t drape loosely or leave coiled up.
Using external antennas
To improve FM reception
Use a PAL connector (not supplied) to connect an external
FM antenna.
Plugging in
Before making or changing the connections, switch off the
power and disconnect the power cord from the AC outlet.
After you’ve finished making all connections, plug the unit
into an AC outlet.
CAUTION
• Do not use any power cord other than the one supplied
with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
AM
LOOP
ANTENNA
FM
UNBAL 75 Ω
2
1
3
4
fig. a fig. b
ANTENNA
FM
UNBAL 75 Ω
One-touch PAL
connector
75 Ω coaxial
cable
VIDEO LINE
AC IN
OUT IN
SPEAKERS
L
R
R L
To AC outlet
This unit’s rear panel
Power cord
X-CM31_SYXE8_En.book 11 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 11 2012/7/5 10:44:08
Page: 11
Getting started
04
12
En
Chapter 4:
Getting started
To turn the power on
Press the  STANDBY/ON to turn the power on.
After use:
Press the  STANDBY/ON to enter the power stand-by mode.
Note
• In standby mode, if iPod/iPhone/iPad is connected, the
unit turns charge mode.
Setting the clock
1 Press  STANDBY/ON to turn the power on.
2 Press CLOCK/TIMER on the remote control.
“CLOCK” is shown on the main display.
3 Press ENTER.
4 Press / to set the day, then press ENTER.
5 Press / to set the hour, then press
ENTER.
6 Press / to set the minute, then press
ENTER to confirm.
To confirm the time display:
Press the CLOCK/TIMER. The time display will appear for
about 10 seconds.
To readjust the clock:
Perform “Setting the clock” from step 1.
Note
• When power supply is restored after unit is plugged in
again or after a power failure, reset the clock.
General control
Input function
When the INPUT on main unit is pressed, the current function
will change to different mode. Press the INPUT repeatedly to
select desired function.
Display brightness control
Press DIMMER to dims the display brightness. The
brightness can be controlled in four steps.
Volume auto set-in
If you turn off and on the main unit with the volume set to 17
or higher, the volume starts at 16 and sets in to the last set
level.
Volume control
Turn the volume knob towards VOLUME (on main unit) or
press VOLUME +/- (on remote control) to increase or
decrease the volume.
CAUTION
• The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It
is advisable to avoid exposure to high volume levels. Do
not turn the volume on to full at switch on. Listen to
music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Muting
The volume is muted temporarily when pressing the MUTE on
the remote control. Press again to restore the volume.
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
1 2 3
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
OPEN/CLOSE
DISPLAY FOLDER
MENU
PRESET VOLUME
TUNE–
TUNE+
MEMORY
/PROGRAM
ENTER
CD AM USB/IPOD
FM
AUDIO IN IPOD
LINE
X-CM31_SYXE8_En.book 12 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 12 2012/7/5 10:44:08
Page: 12
Getting started 04
13
En
English
Français
Español
Sound controls
Equalizer
When the EQUALIZER is pressed, the current mode setting
will be displayed. To change to a different mode, press the
EQUALIZER repeatedly until the desired sound mode
appears.
P.bass control
When the power is first turned on, the unit will enter the
P.bass mode which emphasises the bass frequencies. To
cancel the P.bass mode, press the P.BASS on the remote
control.
Bass/treble control
Press the BASS/TREBLE, then press / to adjust the bass
or treble.
Note
EQUALIZER, P.BASS and BASS/TREBLE, the simultaneous
operation is not possible. Among the features of these three,
one feature will only work you have selected.
If you select one of three functions, features
that are not selected will be set as follows.
1 If you change the settings of P.BASS (ON/
OFF).
• EQUALIZER : FLAT
• BASS/TREBLE : BASS=0, TREBLE=0
2 If you change the settings of EQUALIZER.
• P.BASS : OFF
• BASS/TREBLE : BASS=0, TREBLE=0
3 If you change the settings of BASS/TREBLE.
• P.BASS : OFF
• EQUALIZER : FLAT
Setting the wake-up timer
Used to change the existing timer setting, or to set a new
timer.
1 Press  STANDBY/ON to turn the power on.
2 Press and hold CLOCK/TIMER.
3 Press / to select “ONCE” or “DAILY”,
then press ENTER.
ONCE – Once timer play works for one time only at a
preset time.
DAILY – Daily timer play works at the same preset time
and days of week.
4 Press / to select “TIMER SET”, then
press ENTER.
5 Press / to select the timer playback
source, then press ENTER.
• CD, FM, AM, USB/IPOD, IPOD, AUDIO IN and LINE can
be selected as the playback source.
6 Press / to select the timer day, then
press ENTER.
7 Press / to set the hour, then press
ENTER.
8 Press / to set the minute, then press
ENTER.
• Set the time to finish as in steps 7 and 8 above.
9 Adjust the volume press VOLUME +/- , then
press ENTER.
10 Press  STANDBY/ON to enter the power
standby mode.
• The TIMER indicator lights up.
POP
FLAT Equalizer off.
JAZZ
ROCK
For pop music.
For jazz.
For rock.
X-CM31_SYXE8_En.book 13 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 13 2012/7/5 10:44:08
Page: 13
Getting started
04
14
En
Calling the wake-up timer
It can be used to re-use an existing timer setting.
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
2 Press / to select “TIMER ON”, then press
ENTER.
Cancelling the wake-up timer
It can be used to turn off the timer setting.
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
2 Press / to select “TIMER OFF”, then
press ENTER.
Using the wake-up timer
1 Press  STANDBY/ON to turn the power
off.
2 At the wake-up time, this unit will turn on
automatically and play the selected input
function.
Note
• If at the wake-up time iPod/iPhone/iPad is not connected
to this unit or a disc is not inserted, this unit will be
turned to on and not play back the track.
• Some discs may not be played automatically at the wake-
up time.
• If you set the timer, take one minute or more between the
start and end time.
Using the sleep timer
The sleep timer switches off the unit after a specified time so
you can fall asleep without worrying about it.
1 Press SLEEP repeatedly to select a switch off
time.
Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120
min, 150 min, 180 min or OFF. The newly set value displays for
3 seconds, and then the setting is completed.
Note
• The sleep timer can be set by pressing SLEEP while the
remaining time is displayed.
Using Headphones
Connect to the jack plug of the headphones.
When the headphones are connected, there is no sound
output from the speakers.
• Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
• Before plugging in or unplugging the headphone,
reduce the volume.
• Be sure your headphone has a 3.5 mm diameter plug
and impedance between 16 Ω and 50 Ω. The
recommended impedance is 32 Ω.
• Audio from the iPod/iPhone/iPad cannot be heard via
the headphones connected to the unit. “HP MUTE” will
be displayed if you connect the headphones when the
iPod/iPhone/iPad function is selected.
TIMER VOLUME
PHONES AUDIO IN iPad
X-CM31_SYXE8_En.book 14 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 14 2012/7/5 10:44:08
Page: 14
iPod/iPhone/iPad playback 05
15
En
English
Français
Español
Chapter 5:
iPod/iPhone/iPad playback
Merely by connecting your iPod/iPhone/iPad to this unit, you
can enjoy high-quality sound from your iPod/iPhone/iPad.
This unit can also be connected to a television set, letting you
view videos from your iPod/iPhone. Playback setting for iPod/
iPhone/iPad music can be performed from this unit or the
iPod/iPhone/iPad itself.
• To connect a TV, see page 10.
Confirming what iPod/iPhone/iPad
models are supported
The iPod/iPhone/iPad playable on this unit are shown below.
• Video output for iPod/iPhone is only compatible when
connected to the Dock connector.
Note
• Pioneer does not guarantee that this unit plays iPod/
iPhone/iPad models other than the ones specified.
• Some functions may be restricted depending on the
model or software version.
• iPod/iPhone/iPad is licensed for reproduction of non-
copyrighted materials or materials the user is legally
permitted to reproduce.
• Features such as the equalizer cannot be controlled
using this system, and we recommend switching the
equalizer off before connecting.
• Pioneer cannot under any circumstances accept
responsibility for any direct or indirect loss arising from
any inconvenience or loss of recorded material resulting
from iPod/iPhone/iPad failure.
• For detailed instructions on using the iPod/iPhone/iPad,
please refer to the manual supplied with the iPod/
iPhone/iPad.
• This system has been developed and tested for the
software version of iPod/iPhone/iPad indicated on the
website of Pioneer (http://pioneer.jp/homeav/support/
ios/eu/).
• Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone/iPad may result
in incompatibility with this system.
• This unit cannot be used to record CD, tuner or other
content on an iPod/iPhone/iPad.
Connecting your iPod/iPhone/iPad
CAUTION
• When connecting iPod/iPhone devices, always use the
dock adapter provided with iPod/iPhone devices, or a
commercially available adapter designed to support
iPod/iPhone. The iPod/iPhone cannot be connected
without a dock adapter; attempting to connect an iPod/
iPhone without it will cause damage or malfunction.
• An iPod/iPhone universal dock adapter is not supplied
with this unit.
Important
• If you are mounting the protective cover of a
commercially available iPod/iPhone/iPad, you may not
be able to connect iPod/iPhone/iPad to this unit.
Connecting iPod/iPhone to the top
panel
1 Press the PUSH OPEN.
iPod/iPhone/iPad Dock connector
(Audio/Video)
USB Terminal
(Audio only)
iPod nano 3G/4G/5G/6G*
* iPod nano 6G is supports audio only.
 
iPod touch 1G/2G/3G/4G  
iPhone  
iPhone 3G  
iPhone 3GS  
iPhone 4  
iPhone 4S  
iPad — 
iPad 2 — 
PUSH
OPEN
X-CM31_SYXE8_En.book 15 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 15 2012/7/5 10:44:08
Page: 15
iPod/iPhone/iPad playback
05
16
En
2 Open the iPod/iPhone connector port.
3 Connect your iPod/iPhone.
• When iPod/iPhone is not connected to the unit, close
the iPod/iPhone connector port firmly.
Connecting iPod/iPhone/iPad using
supplied stand
1 Connect the iPod/iPhone/iPad cable to the
unit.
2 From the bottom of the connector to
through the iPod/iPhone/iPad cable, and
connect it to iPod/iPhone/iPad.
3 Set up to stand the iPod/iPhone/iPad.
Watching iPod/iPhone videos on your
TV
To watch iPod/iPhone videos on a television, connect it using
a video cable. When an iPod/iPhone is connected to this unit,
the TV output setting of the iPod/iPhone is automatically set
to ‘ON’.
CAUTION
• Before making or changing the connections, switch off
the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
Note
• For detailed instructions on using the iPod/iPhone,
please refer to the manual supplied with the iPod/
iPhone.
• Some iPods allow the TV output setting to be changed
while connected.
PUSH
OPEN
X-CM31_SYXE8_En.book 16 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 16 2012/7/5 10:44:08
Page: 16
iPod/iPhone/iPad playback 05
17
En
English
Français
Español
• When the iPod/iPhone is disconnected from this unit,
the iPod/iPhone’s TV output setting returns to its original
state.
Playing iPod/iPhone
1 Connect your iPod/iPhone.
• If an iPod/iPhone is connected when this unit is on,
playback of the iPod/iPhone will not begin.
2 Press iPod or USB as the input source.
“IPOD” or “USB/IPOD” is shown on the main display.
3 When the recognition is completed, will
begin playing automatically.
• The available iPod/iPhone playback control by this unit is
,  ,  .
• In the following case, operate your iPod/iPhone directly:
- Searching a file by artist name or genre.
- Playing in the repeat or random mode.
- Watching videos stored in iPod/iPhone on your television.
Playing iPad
1 Connect your iPad.
• If an iPad is connected when this unit is on, playback of
the iPad will not begin.
2 Press USB as the input source.
“USB/IPOD” is shown on the main display.
3 When the recognition is completed, will
begin playing automatically.
• The available iPad playback control by this unit is ,
 ,  .
• In the following case, operate your iPad directly:
- Searching a file by artist name or genre.
- Playing in the repeat or random mode.
CAUTION
• When your iPod/iPhone/iPad is connected to this unit
and you wish to operate the iPod/iPhone/iPad directly,
be sure to steady the iPod/iPhone/iPad with the other
hand to prevent malfunctions due to faulty contacts.
Note
• For detailed instructions on using the iPod/iPhone/iPad,
please refer to the manual supplied with the iPod/
iPhone/iPad.
• iPod/iPhone/iPad recharging occurs whenever an iPod/
iPhone/iPad is connected to this unit. (This function is
supported in standby mode as well.)
• When input is switched from iPod to another function,
iPod/iPhone/iPad playback is temporarily stopped.
Important
If this unit cannot play your iPod/iPhone/iPad, perform the
following troubleshooting checks:
• Check whether the iPod/iPhone/iPad is supported by
this unit.
• Reconnect the iPod/iPhone/iPad to the unit. If this
doesn’t seem to work, try resetting your iPod/iPhone/
iPad.
• Check the iPod/iPhone/iPad software is supported by
this unit.
If the iPod/iPhone/iPad cannot be operated, check the
following items:
• Is the iPod/iPhone/iPad connected correctly?
Reconnect the iPod/iPhone/iPad to the unit.
• Is the iPod/iPhone/iPad experiencing a hangup? Try
resetting the iPod/iPhone/iPad, and reconnect it to the
unit.
X-CM31_SYXE8_En.book 17 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 17 2012/7/5 10:44:08
Page: 17
Disc playback
06
18
En
Chapter 6:
Disc playback
This system can play back a standard CD, CD-R/RW in the CD
format and CD-R/RW with MP3 or WMA files, but cannot
record on them. Some audio CD-R and CD-RW discs may not
be playable due to the state of the disc or the device that was
used for recording.
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3. MP3 is a type of audio code which is
processed by significant compression from the original audio
source with very little loss in sound quality.
• This system supports MPEG-1/2 Audio Layer 3 (Sampling
rates: 8 kHz to 48 kHz; Bit rates: 64 kbps to 384 kbps).
• During VBR file playback, time counter in the display
may differ from its actual playback time.
WMA:
WMA (Windows Media Audio) files are Advanced System
Format files that include audio files which are compressed
with Windows Media Audio codec. WMA is developed by
Microsoft as an audio format file for Windows Media Player.
• This system supports WMA (Sampling rates: 32 kHz/44.1
kHz/48 kHz; Bit rates: 64 kbps to 320 kbps).
• During VBR file playback, time counter in the display
may differ from its actual playback time.
Playing discs or files
1 Press  STANDBY/ON to turn the power on.
2 Press CD on the remote control or INPUT
repeatedly on the main unit to select CD input.
3 Press  OPEN/CLOSE to open the disc tray.
4 Place the disc on the disc tray, label side up.
5 Press  OPEN/CLOSE to close the disc tray.
6 Press  to start playback.
After the last track is played, the unit will stop automatically.
CAUTION
• Do not place two discs in one disc tray.
• Do not play discs of special shapes (heart, octagon, etc).
It may cause malfunctions.
• Do not push the disc tray whilst it is moving.
• If the power fails whilst the tray is open, wait until the
power is restored.
• Be sure to place 8 cm disc in the middle of the disc tray.
Note
• Due to the structure of the disc information, it takes longer
to read an MP3/WMA disc than a normal CD
(approximately 20 to 90 seconds).
• When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode (only for CD).
• Rewritable multi-session discs with unfinished writing, can
still be played.
• If TV or radio interference occurs during CD operation,
move the unit away from the TV or radio.
Tip
• When no operation has done in CD mode and the audio
file is not played for more than 15 minutes, the power will
automatically turn off.
Various disc functions
Function Main
unit
Remote
control
Operation
Play Press in the stop mode.
Stop Press in the playback mode.
Pause Press in the playback mode.
Press  to resume playback
from the paused point.
Track up/
down
Press in the playback or stop
mode.
If you press the button in the
stop mode, press  to start
the desired track.
Fast
forward/
reverse
Press and hold down in the
playback mode.
Release the button to resume
playback.
 
 
 
 
 
 
 
 
 
X-CM31_SYXE8_En.book 18 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 18 2012/7/5 10:44:09
Page: 18
Disc playback 06
19
En
English
Français
Español
Advanced CD or MP3/WMA disc
playback
Direct track search
By using the numeric buttons, the desired tracks on the
current disc can be played.
Use the numeric buttons on the remote control to
select the desired track whilst playing the selected
disc.
Note
• A track number higher than the number of tracks on the
disc cannot be selected.
To stop playback:
Press .
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press REPEAT repeatedly until “RPT ONE” appears. Press
ENTER.
To repeat all tracks:
Press REPEAT repeatedly until “RPT ALL” appears. Press
ENTER.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on next
page and then press REPEAT repeatedly until “RPT ALL”
appears. Press ENTER.
To cancel repeat play:
Press REPEAT repeatedly until “RPT OFF” appears. Press
ENTER.
Note
• After performing repeat play, be sure to press .
Otherwise, the disc will play continuously.
• During repeat play, random play is not possible.
Random play
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press RANDOM repeatedly until “RDM ON” appears. Press
ENTER.
To cancel random play:
Press RANDOM repeatedly until “RDM OFF” appears. Press
ENTER.
Note
• If you press the  during random play, you can move
to the track selected next by the random operation. On
the other hand, the  does not allow you to move to
the previous track. The beginning of the track being
played will be located.
• In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
• During random play, repeat play is not possible.
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
DISPLAY FOLDER
TUNE+
1 2 3
4 5 6
7 8 9
0
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR REPEAT
OPEN/CLOSE DISPLAY FOLDER
MENU
PRESET VOLUME
ST/MONO ASPM PTY DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
   
 
–
+
–
MEMORY
/PROGRAM
0
RDS
ENTER
X-CM31_SYXE8_En.book 19 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 19 2012/7/5 10:44:09
Page: 19
Disc playback
06
20
En
Programmed play (CD or MP3/WMA)
You can choose up to 32 selections for playback in the order
you like.
1 Whilst in the stop mode, press MEMORY/
PROGRAM on the remote control to enter the
programming save mode.
2 Press   or the numeric buttons on the
remote control to select the desired tracks.
3 Press ENTER to save folder and track
number.
4 Repeat steps 2 - 3 for other folder/tracks. Up
to 32 tracks can be programmed.
• If you want to check the programmed tracks, press
MEMORY/PROGRAM.
• If you make a mistake, the last programmed tracks will
be canceled by pressing CLEAR.
5 Press  to start playback.
To cancel the programmed play mode:
To cancel the programmed play, press twice  on the remote
control. The display will show “PRG CLR” and all the
programmed contents will be cleared.
Adding tracks to the program:
Press the MEMORY/PROGRAM. Then follow steps 2 - 3 to
add tracks.
Note
• When a disc is ejected, the program is automatically
cancelled.
• If you press the  STANDBY/ON to enter the standby
mode or change the function from CD to another, the
programmed selections will be cleared.
• During the program operation, random play is not
possible.
About downloading MP3/WMA
There are many music sites on the internet that you can
download MP3/WMA music files. Follow the instructions
from the website on how to download the music files. You can
then play back these downloaded music files by burning them
to a CD-R/RW disc.
• Your downloaded song/files are for personal use only.
Any other usage of the song without owner’s permission,
is against the law.
About folder playback order
If MP3/WMA files are recorded in several folders, a folder
number will be set to each folder automatically.
These folders can be selected by the FOLDER on the remote
control. If there is no supported file formats inside the
selected folder, the folder is skipped and the next folder will be
selected.
Example: How to set folder number if MP3/WMA format files
are recorded as below figure.
1 ROOT folder is set as folder 1.
2 As for folders inside ROOT folder (Folder A
and Folder B), the folder which is recorded
earlier on the disc will be set as folder 2 and
folder 3.
3 As for folder inside Folder A (Folder C and
Folder D), the folder which is recorded earlier on
the disc will be set as folder 4 and folder 5.
4 Folder E that is inside Folder D will be set as
folder 6.
• The folder and file order information which is recorded
on the disc depends on the writing software. There
maybe possibilities that this unit will playback the files
not according to our expected playback order.
• MP3/WMA is 255 numbers of folders and 999 files
inclusive of the folders which have non playable files can
be read.
ROOT
(FOLDER 1)
FOLDER A
(FOLDER 2)
FOLDER B
(FOLDER 3)
FILE 9
FILE 10
FILE 3
FILE 4
FILE 5
FILE 6
FILE 7
FILE 8
FOLDER E
(FOLDER 6)
FOLDER C
(FOLDER 4)
FOLDER D
(FOLDER 5)
FILE 1
FILE 2
X-CM31_SYXE8_En.book 20 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 20 2012/7/5 10:44:09
Page: 20
Disc playback 06
21
En
English
Français
Español
Specify the folder to play
Specify the folder to play, do the follwing steps.
1 Press CD, and load an MP3/WMA disc.
2 Press FOLDER, and press / to select
desired playback folder.
3 Press ENTER.
Playback will start from the first song of the selected folder.
• In case of stop, press /, and the folder can be
selected.
Switch the display contents
1 Press DISPLAY.
If the title, artist and album name has been written to the file,
that information will be displayed. (You can view this unit is
only alphanumeric characters. Non- alphanumeric character
are displayed in the ”*”.)
Note
• “Copyright protected WMA file” or “Not supported
playback file” can not be playback. In this case, will be
skipped automatically.
• Some files, you may no information is displayed.
• Title, artist and album name, and supports only MP3.
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
DISPLAY FOLDER
TUNE+
1 2 3
4 5 6
7 8 9
0
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR REPEAT
OPEN/CLOSE
DISPLAY FOLDER
MENU
PRESET VOLUME
ST/MONO ASPM PTY DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
   
 
–
+
–
MEMORY
/PROGRAM
0
RDS
ENTER
Title/Artist/Album display
Number of track, playback
time display
Kind of file display
Number of folder/track
display
X-CM31_SYXE8_En.book 21 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 21 2012/7/5 10:44:09
Page: 21
USB playback
07
22
En
Chapter 7:
USB playback
Playing USB storage devices
It is possible to listen to two-channel audio using the USB
interface on the front of this receiver.
• Pioneer does not guarantee that any file recorded on a
USB storage device will play or that power will be
supplied to a USB storage device. Also note that Pioneer
will accept no responsibility whatsoever for loss of files
on USB storage devices caused by connection to this
unit.
1 Press USB as the input source.
“USB/IPOD” is shown on the main display.
2 Connect the USB storage device.
The number of folders or files stored on the connected USB
storage device appear on the main display automatically.
• This receiver does not support a USB hub.
• If iPod/iPhone/iPad is connected, the unit will begin
charging.
3 When the recognition is completed, press
 to start playback.
• When changing to a different input source, stop the USB
memory playback first, before changing.
4 Disconnect USB storage device from the USB
terminal.
Turn the power off before removing the USB storage device.
Note
• This unit may not recognize a USB storage device, play
files or supply power to a USB storage device. For
details, see When a USB storage device is connected on
page 29.
• When a USB storage device is not playing and the unit
has not been operated for 15 minutes or more, the power
will automatically turn off.
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press REPEAT repeatedly until “RPT ONE” appears. Press
ENTER.
To repeat all tracks:
Press REPEAT repeatedly until “RPT ALL” appears. Press
ENTER.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on next
page and then press REPEAT repeatedly until “RPT ALL”
appears. Press ENTER.
To cancel repeat play:
Press REPEAT repeatedly until “RPT OFF” appears. Press
ENTER.
Note
• After performing repeat play, be sure to press .
Otherwise, the file of USB storage device will play
continuously.
• During repeat play, random play is not possible.
Random play
The file of USB storage device can be played in random order
automatically.
To random play all tracks:
Press RANDOM repeatedly until “RDM ON” appears. Press
ENTER.
To cancel random play:
Press RANDOM repeatedly until “RDM OFF” appears. Press
ENTER.
Note
• If you press the  during random play, you can move
to the track selected next by the random operation. On
the other hand, the  does not allow you to move to
the previous track. The beginning of the track being
played will be located.
• In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
• During random play, repeat play is not possible.
TIMER VOLUME
iPad
USB storage device
(commercially available)
X-CM31_SYXE8_En.book 22 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 22 2012/7/5 10:44:09
Page: 22
USB playback 07
23
En
English
Français
Español
Specify the folder to play
Specify the folder to play, do the follwing steps.
1 Press USB, and connect the USB storage
device.
2 Press FOLDER, and press / to select
desired playback folder.
3 Press ENTER.
Playback will start from the first song of the selected folder.
• In case of stop, press /, and the folder can be
selected.
Switch the display contents
This unit can switch the information recorded in the USB
storage device. For details, see Switch the display contents on
page 21.
Playing in the desired order
(Programmed Play)
This unit can play repeatedly folders stored in the USB
storage device. For details, see Programmed play (CD or MP3/
WMA) on page 20.
X-CM31_SYXE8_En.book 23 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 23 2012/7/5 10:44:09
Page: 23
Using the tuner
08
24
En
Chapter 8:
Using the tuner
Listening to the radio broadcasts
The following steps show you how to tune in to FM and AM
radio broadcasts using the automatic (search) and manual
(step) tuning functions. Once you are tuned to a station you
can memorize the frequency for recall later. See Saving
station presets below for more on how to do this.
Tuning
1 Press the  STANDBY/ON to turn the power
on.
2 Press TUNER repeatedly to select desired
frequency band (FM or AM).
3 Press TUNE +/– on the remote control to
tune in to the desired station.
Automatic tuning:
Press and hold TUNE +/–, scanning will start automatically
and the tuner will stop at the first receivable broadcast
station.
Manual tuning:
Press the TUNE +/– repeatedly to tune in to the desired
station.
Note
• When radio interference occurs, automatic tuning may
stop automatically at that point.
• Automatic tuning will skip weak signal stations.
• To stop the automatic tuning, press .
• When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first. Finally, the station
name will appear.
• Full auto tuning can be achieved for RDS stations
“ASPM”, see page 26.
To receive an FM stereo transmission:
• Press ST/MONO to select stereo mode and “AUTO” will
be displayed.
Improving poor FM reception:
1 Press ST/MONO repeatedly to select MONO.
This will change the tuner from stereo to mono and usually
improve the reception.
Saving station presets
If you often listen to a particular radio station, it’s convenient
to have the receiver store the frequency for easy recall
whenever you want to listen to that station (Preset tuning).
This saves the effort of manually tuning in each time. This unit
can memorize up to 45 stations.
(FM 30 stations/AM 15 stations)
1 Tune to a station you want to memorize.
See Tuning above for more on this.
2 Press MEMORY/PROGRAM.
The preset number will flash.
3 Press PRESET +/– to select the preset
channel number.
4 Press MEMORY/PROGRAM to store that
station in memory.
If the preset number has changed from flashing to lighting,
before the station is memorised, repeat the operation from
step 2.
• Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note
• The backup function protects the memorised stations for
a few hours should there be a power failure or the AC
power cord become disconnected.
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
DISPLAY FOLDER
TUNE+
1 2 3
4 5 6
7 8 9
0
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR REPEAT
OPEN/CLOSE
DISPLAY FOLDER
MENU
PRESET VOLUME
ST/MONO ASPM PTY DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
   
 
–
+
–
MEMORY
/PROGRAM
0
RDS
ENTER
DISPLAY FOLDER
MENU
PRESET VOLUME
+
MUTE
TUNE–
TUNE+
DIMMER
 
–
+
–
MEMORY
/PROGRAM
0
ENTER
DISPLAY FOLDER
MENU
PRESET VOLUME
+
MUTE
TUNE–
TUNE+
–
+
–
MEMORY
/PROGRAM
0
RANDOM
CLEAR REPEAT
ENTER
X-CM31_SYXE8_En.book 24 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 24 2012/7/5 10:44:09
Page: 24
Using the tuner 08
25
En
English
Français
Español
To recall a memorised station
1 Press PRESET +/– to select the desired
station.
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1 Press and hold PRESET +/–.
The preset number will appear and the programmed stations
will be tuned in sequentially, for 5 seconds each.
2 Press PRESET +/– again when the desired
station is located.
To erase entire preset memory
1 Press TUNER on the remote control.
2 Press CLEAR until “MEM CLR” appears.
Note
• All stations will be erased.
Using the Radio Data System (RDS)
An introduction to RDS
Radio Data System (RDS) is a system used by most FM radio
stations to provide listeners with various kinds of
information—the name of the station and the kind of show
they’re broadcasting, for example.
One feature of RDS is that you can search by type of program.
For example, you can search for a station that’s broadcasting
a show with the program type, JAZZ.
You can search the following program types:
Searching for RDS programs
You can search a program type listed above.
1 Press TUNER on the remote control.
• RDS is only possible in the FM.
2 Press RDS PTY on the remote control.
“SELECT” will appear for about 6 seconds.
3 Press / to select the program type you
want to hear.
Each time the button is pressed, the program type will appear.
If the button is held down, the program type will appear
continuously.
4 Whilst the selected program type is flashing
(within 6 seconds), Press RDS PTY again.
After the selected program type has been lit for 2 seconds,
“SEARCH” will appear, and the search operation will start.
Note
• If the display has stopped flashing, start again from step
2. If the unit finds a desired program type, the
corresponding channel number will lit for about 8
seconds, and then the station name will remain it.
• If you want to listen to the same program type of another
station, press the RDS PTY whilst the channel number or
station name is flashing. The unit will look for the next
station.
• If no station can be found, “NOT FOUND” will appear for
4 seconds.
NEWS – News
AFFAIRS – Current Affairs
INFO – General Information
SPORT – Sport
EDUCATE – Educational
DRAMA – Radio plays, etc.
CULTURE – National or
regional culture, theater, etc.
SCIENCE – Science and
technology
VARIED – Usually talk-based
material, such as quiz shows
or interviews.
POP M – Pop music
ROCK M – Rock music
EASY M – Easy listening
LIGHT M – ‘Light’ classical
music
CLASSICS – ‘Serious’ classical
music
OTHER M – Music not fitting
above categories
WEATHER – Weather reports
FINANCE – Stock market
reports, commerce, trading,
etc.
CHILDREN – Programs for
children
SOCIAL – Social affairs
RELIGION – Programs
concerning religion
PHONE IN – Public expressing
their views by Phone
TRAVEL – Holiday-type travel
rather than traffic
announcements
LEISURE – Leisure interests
and hobbies
JAZZ – Jazz
COUNTRY – Country music
NATION M – Popular music in
a language other than English
OLDIES – Popular music from
the ‘50s and’ 60s
FOLK M – Folk music
DOCUMENT – Documentary
TEST – Broadcasting when
testing emergency broadcast
equipment or receivers.
ALARM – Emergency
announcement made under
exceptional circumstances to
give warning of events causing
danger of a general nature.
X-CM31_SYXE8_En.book 25 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 25 2012/7/5 10:44:09
Page: 25
Using the tuner
08
26
En
Information provided by RDS
Each time the RDS DISPLAY is pressed, the display will switch
as follows:
When tuning in to a station other than an RDS station or to an
RDS station which sends weak signal, the display will change
in the following order:
Using the Auto Station program
Memory (ASPM)
Whilst in the ASPM operation mode, the tuner will
automatically search for new RDS stations. Up to 30 stations
can be stored.
If you have already stored some stations in memory, the
number of new stations you can store will be less.
1 Press TUNER on the remote control.
2 Press and hold down RDS ASPM on the
remote control.
After “ASPM” has flashed for about 4 seconds, scanning will
start (87.5 - 108 MHz).
After scanning, the number of stations stored in memory will
be displayed for 4 seconds, and then “END” will appear for 4
seconds.
To stop the ASPM operation before it is
complete:
Press  whilst it is scanning for stations. The stations which
are already stored in memory will be kept there.
Note
• If the same station is broadcasting on different
frequencies, the strongest frequency will be stored in
memory.
• Any station which has the same frequency as the one
stored in memory will not be stored.
• If 30 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
• If no station have been stored in memory, “END” will
appear for about 4 seconds.
• If the RDS signals are very weak, station names may not
be stored in memory.
• The same station name can be stored in different
channels.
• In a certain area or during certain time periods, the
station names may temporarily be different.
Notes for RDS operation
If any of the following events occur, it does
not mean that the unit is faulty:
• “PS”, “No PS” and a station name appear alternately,
and properly.
• If a particular station is not broadcasting properly or a
station is conducting tests, the RDS reception function
may not work properly.
• When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
• “No PS”, “No PYT” or “No RT” will flash for about 5
seconds, and then the frequency will be displayed.
Notes for radio text:
• The first 8 characters of the radio text will appear and
then they will scroll across the display.
• If you tune in to an RDS station which is not
broadcasting any radio text, “No RT” will be displayed
when you switch to the radio text position.
• Whilst radio text data is received or when the text
contents change, “RT” will be displayed.
STANDBY/ON
 
iPod CD USB TUNER
AUDIO IN/LINE
DISPLAY FOLDER
TUNE+
1 2 3
4 5 6
7 8 9
0
TV OUT CLOCK/TIMER SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR REPEAT
OPEN/CLOSE
DISPLAY FOLDER
MENU
PRESET VOLUME
ST/MONO ASPM PTY DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
   
 
–
+
–
MEMORY
/PROGRAM
RDS
ENTER
Station name (PS) Programme type (PTY)
Frequency Radio text (RT)
No RDS
FM 98.80 MHz
X-CM31_SYXE8_En.book 26 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 26 2012/7/5 10:44:09
Page: 26
Other connections 09
27
En
English
Français
Español
Chapter 9:
Other connections
CAUTION
• Before making or changing the connections, switch off
the power and disconnect the power cord from the AC
outlet.
Connecting auxiliary components
Connect the front panel AUDIO IN mini-plug jack to your
auxiliary playback component.
• This method can be used to play music on this unit from
iPods/iPhones/iPads that do not support use of an iPod
Dock and USB terminal.
1 Press AUDIO IN/LINE as the input source.
When AUDIO IN is selected, “AUDIO IN” is displayed on the
main display.
Note
• If the AUDIO IN mini-plug jack is connected to auxiliary
phones jack, the volume of the unit will be adjusted by
the volume on the playback component. If the sound is
distorted after you lower the volume of the unit, try
lowering the volume on the auxiliary playback
component.
Connect the rear panel LINE IN audio jacks to your auxiliary
playback component.
1 Press AUDIO IN/LINE twice as the input
source.
When LINE is selected, “LINE” is displayed on the main
display.
TIMER VOLUME
PHONES AUDIO IN iPad
PHONES AUDIO IN
Portable audio player, etc.
Stereo mini-plug
cable (commercially
available)
AM
LOOP
NNA VIDEO LINE
OUT IN
S
L
R
FM
UNBAL 75 Ω
TV
This unit’s rear panel
Audio cable
(commercially available)
X-CM31_SYXE8_En.book 27 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 27 2012/7/5 10:44:09
Page: 27
Additional information
10
28
En
Chapter 10:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components
and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your
nearest Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the
outlet and insert again to return to normal operating conditions.
General problem
Problem Check Remedy
Settings you have made have
been cleared.
Was the power cord unplugged? When power cord is unplugged, the settings you have made is
cleared. Please set the clock again. If you do not want to clear the
settings, do not unplug the power cord.
Difference in volume
between CDs, MP3, WMA,
iPod/iPhone/iPad, Tuner,
AUDIO IN and LINE.
This is not a problem with this unit. The volume may sound differently depending on the input source
and recording format.
This unit cannot be operated
with the remote control.
Are you operating from far away? Operate within 7 m, 30º of the remote sensor on the front panel
(page 5).
Is the remote control sensor exposed
to direct sunlight or strong artificial
light from a fluorescent bulb, etc.?
The remote control signals may not be received properly if the
remote control sensor is exposed to direct sunlight or strong
artificial light from a fluorescent bulb, etc.
Are the batteries dead? Replace the batteries (page 5).
Disc cannot be played or disc
is ejected automatically.
Is the disc scratched? Scratched discs may not play.
Is the disc dirty? Wipe the dirt off the disc (page 31).
Is this unit placed in a humid
location?
There could be condensation inside. Wait a while for the
condensation to evaporate. Do not place this unit near an air-
conditioner, etc. (page 31).
Folder or file names are not
recognized.
Have you exceeded the maximum
number of folder or file names this
unit can recognize?
Up to 255 folders can be recognized on one disc. Up to 999 files can
be recognized within one folder. Depending on the folder structure,
however, this unit may not be able to recognize certain folders or
files.
The unit turns off
automatically.
If no play back and no operation has done for 15 minutes or more,
the unit turns off automatically.
X-CM31_SYXE8_En.book 28 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 28 2012/7/5 10:44:09
Page: 28
Additional information 10
29
En
English
Français
Español
When a USB storage device is connected
When an iPod/iPhone/iPad is connected
Problem Check Remedy
USB storage device is not
recognized.
Is the USB storage device properly
connected?
Connect the device securely (all the way in).
Is the USB storage device connected
via a USB hub?
This unit does not support USB hubs. Connect the USB storage
device directly.
This unit only supports USB mass storage class devices.
This unit supports portable flash memory and digital audio
playback devices.
Only the FAT16 and FAT32 file systems are supported. Other file
systems (exFAT, NTFS, HFS etc.) are not supported.
This device does not support the use of external hard disc drives.
This is not a problem with this unit. Turn the power off then back on.
Some USB storage devices may not be recognized properly.
File cannot be played. Is the file copyright-protected (by
DRM)?
Copyright-protected files cannot be played.
This is not a problem with this unit. Files stored on a computer cannot be played.
It may not be possible to play some files.
Folder or file names are not
displayed or are not properly
displayed.
Do the folder of file names contain
more than 30 characters?
The maximum number of characters displayable for the folder and
file names is 30.
Folder or file names are not
displayed in alphabetical
order.
This is not a problem with this unit. The order of the folder and file names displayed depends on the
order in which the folders or files were recorded on the USB
storage device.
Much time is required to
recognize the USB storage
device.
What is the USB storage devices
capacity?
Some time may be required to load the data when large capacity
USB storage devices are connected (this could take several
minutes).
Power is not supplied to the
USB storage device.
Is AUTH ERR displayed on the front
panel display? No power is supplied if
the power consumption is too high.
Turn the power off then back on.
Turn the power off, then disconnect and reconnect the USB storage
device.
Press INPUT to switch to the other mode, then switch again to the
USB mode.
Problem Remedy
Can’t operate the iPod/iPhone/iPad by the remote control. Make sure the iPod/iPhone/iPad is connected correctly (refer to
Connecting your iPod/iPhone/iPad on page 15).
Can’t operate the iPod/iPhone/iPad. Make sure the iPod/iPhone/iPad is connected correctly (refer to
Connecting your iPod/iPhone/iPad on page 15).
If the iPod/iPhone/iPad is experiencing a hangup, try resetting the
iPod/iPhone/iPad, and reconnect it to the unit.
X-CM31_SYXE8_En.book 29 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 29 2012/7/5 10:44:09
Page: 29
Additional information
10
30
En
Playable discs and formats
• Only the discs that have been finalized can be
played.
• Discs recorded in packet write mode (UDF format) are
not compatible with this unit.
• Corporation and product names mentioned herein are
trademarks or registered trademarks of the respective
corporations.
• Only discs recorded in ISO9660 Level 1, Level 2 and Joliet
can be played.
• Files protected by DRM (Digital Rights Management)
cannot be played.
Note
• This unit does not support multisession discs or
multiborder recording.
• Multisession/multiborder recording is a method in
which data is recorded on a single disc in two or more
sessions/borders. A “session” or “border” is one
recording unit, consisting of a complete set of data from
lead-in to lead-out.
Regarding copy protected CDs
This unit is designed to conform to the specifications of the
audio CD format. This unit does not support the playback or
function of discs that do not conform to these specifications.
Supported audio file formats
• This unit does not support lossless encoding.
Cautions on use
When moving this unit
When moving this unit, be sure to first check that there is no
disc loaded and disconnect the iPod/iPhone/iPad. Then press
 STANDBY/ON, wait for “STANDBY” disappears on main
display to turn off, then unplug the power cord. Damage may
occur if the unit is transported or moved with a disc inserted,
or when another device is connected to the iPod/iPhone/iPad
connector port, USB terminal, or AUDIO IN mini-plug jack.
Place of installation
• Choose a stable place near the TV or stereo system being
used with this unit.
• Do not place this unit on top of a TV or color monitor. Also
install it away from cassette decks and other devices
easily affected by magnetic forces.
Avoid the following locations:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot places
• Places exposed to vibrations
• Places in which there is much dust or cigarette smoke
• Places exposed to soot, steam or heat (kitchens, etc.)
Audio CD
• Commercially available audio CDs
• CD-R/ -RW/ -ROM discs containing music recorded in the CD-DA format
WMA WMA files recorded on CD-R/ -RW/ -ROM discs or USB storage devices
MP3 MP3 files recorded on CD-R/ -RW/ -ROM discs or USB storage devices
X-CM31_SYXE8_En.book 30 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 30 2012/7/5 10:44:10
Page: 30
Additional information 10
31
En
English
Français
Español
Do not place objects on this unit
Do not place any objects on top of this unit.
Do not obstruct the ventilation holes.
Do not use this unit on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Do not expose to heat.
Do not place this unit on top of an amplifier or other
component that generates heat. When rack mounting it, to
avoid the heat given off by the amplifier or other audio
component, place it on a shelf below the amplifier.
• Turn off the unit’s power when not using it.
• Depending on signal conditions, striped patterns may
appear on a TV screen and noise may enter the sound of
radio broadcasts when the unit’s power is on. If this
happens, turn the unit’s power off.
About condensation
If this unit is moved suddenly from a cold place into a warm
room (in winter, for example) or if the temperature in the room
in which this unit is installed rises suddenly due to heater
operation, etc., water droplets (condensation) may form
inside (on operating parts and the lens). When condensation
is present, this unit will not operate properly and playback is
not possible. Let this unit stand at room temperature for 1 or
2 hours with the power turned on (the time depends on the
extent of condensation). The water droplets will dissipate and
playback will become possible. Condensation can also occur
in the summer if this unit is directly exposed to the air flow
from an air-conditioner. If this happens, move this unit to a
different place.
Cleaning the product
• Unplug the power cord from the power outlet when
cleaning this unit.
• Clean this unit using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a
soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a soft, dry cloth.
• Alcohol, thinner, benzene, insecticides, etc., could cause
the print or paint to peel off. Also, leaving rubber or vinyl
products in contact with this unit for long periods of time
could mar the cabinet.
• When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.
Cleaning the lens
• This unit’s lens should not become dirty in normal use,
but if for some reason it should malfunction due to dust
or dirt, consult your nearest Pioneer authorized service
center. Although lens cleaners for players are
commercially available, we advise against using them
since some may damage the lens.
Handling discs
Storing
• Always place discs in their cases and store them
vertically, avoiding hot, humid places, places exposed to
direct sunlight and extremely cold places.
• Be sure to read the cautions included with the disc.
Cleaning discs
• Discs may not play if there are fingerprints or dust on
them. In this case, use a cleaning cloth, etc., to gently
wipe the disc from the inside towards the outside. Do not
use dirty cleaning cloths.
• Do not use benzene, thinner or other volatile chemicals.
Also do not use record spray or antistatic agents.
• For tough dirt, apply some water to a soft cloth, wring out
thoroughly, wipe off the dirt, then wipe off the moisture
with a dry cloth.
• Do not use damaged (cracked or warped) discs.
• Do not let the signal surface of discs get scratched or
dirty.
• Do not attach pieces of paper or stickers to discs. Doing
so could warp discs, making it impossible to play them.
Also note that rental discs often have labels attached to
them, and the label’s glue may have oozed out. Check
that there is no glue around the edges of such labels
before using rented discs.
About specially shaped discs
Specially shaped discs (heart-shaped, hexagonal, etc.)
cannot be played on this unit. Do not attempt to play such
discs, as they could damage this unit.
X-CM31_SYXE8_En.book 31 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 31 2012/7/5 10:44:10
Page: 31
Additional information
10
32
En
About iPod/iPhone/iPad
“Made for iPod” and “Made for iPhone” and “Made for iPad”
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this
accessory with iPod, iPhone or iPad may affect wireless
performance.
iPad, iPhone, iPod, iPod nano and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.
Restoring all the settings to the
defaults
Use the steps below to restore the all settings to their defaults.
1 Press  STANDBY/ON to turn the power on.
2 Press CD on the remote control or INPUT
repeatedly on the main unit to select CD input.
3 Press  OPEN/CLOSE to open the disc tray.
4 Press  STANDBY/ON while pressing .
Use the buttons on this unit’s top panel. “DEFAULT” is
displayed while the settings are being restored. Power is
turned off.
X-CM31_SYXE8_En.book 32 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 32 2012/7/5 10:44:10
Page: 32
Additional information 10
33
En
English
Français
Español
Specifications
• Amplifier section
RMS Power Output: . . . . . . . . . . . . . . . . . . . . . . . 15 W + 15 W
(1 kHz, 10 %, T.H.D., 8 Ω)
• Tuner section
Frequency Range (FM). . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . . . . . . . . . . . . 75 Ω unbalanced
Frequency Range (AM) . . . . . . . . . . . . . . 522 kHz to 1620 kHz
Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop antenna
• Miscellaneous
iPod/iPhone connector port . . . . . . . . . . . . . . . . . . . . . 5 V, 1 A
USB terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 V, 2.1 A
Power source . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption
Power on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 W
Power stand-by. . . . . . . . . . . . . . . . . . . . . . . . . .0.5 W or less
Dimensions. . . . . .200 mm (W) x 123 mm (H) x 250.6 mm (D)
Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . . 2.0 kg
• Speaker
Magnetically shieled speaker system
Type
2-way type speaker system
5 cm Tweeter
9.4 cm Woofer
Maximum input power. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 W
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Dimensions. . . . . .120 mm (W) x 200 mm (H) x 232.6 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 kg/each
• Accessories
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AAA batteries (R03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
AM antenna cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Non-skid pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power cord
iPad Stand
Warranty card
Operating instructions (This document)
Note
• The specifications are applicable when the power supply
is 230 V.
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
© 2012 PIONEER CORPORATION.
All rights reserved.
X-CM31_SYXE8_En.book 33 ページ 2012年6月7日 木曜日 午後2時4分
YOM2001450001.pdf 33 2012/7/5 10:44:10

Question & answers

There are no questions about the Pioneer X-CM31-K yet.

Ask a question about the Pioneer X-CM31-K

Have a question about the Pioneer X-CM31-K but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer X-CM31-K. Please make sure that you describe your difficulty with the Pioneer X-CM31-K as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.