Pioneer SGY-PM910HL manual

View a manual of the Pioneer SGY-PM910HL below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Bicycle Computer
  • Model/name: SGY-PM910HL
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian

Table of Contents

Page: 0
EN
DE
FR
NE
IT
ES
EN
DE
FR
NL
IT
ES
JP
Please read the "Important Information for the User" in the product box
for product warnings and other important safety information.
User's Manual
Pedaling Monitor Sensor
SGY-PM910H2
SGY-PM910HL
SGY-PM910HR
ペダリングモニターセンサーをご使用になる前に、 必ず本冊子をお読みください。
お読みになったあとは、 大切に保管してください。
ペダリングモニターセンサー
取扱説明書
Page: 1
2
EN
Introduction
Table of Contents
Introduction
Features...................................................................................... 3
Compatibility............................................................................... 6
Getting Started
Product Configuration................................................................. 7
Installing and Removing the Batteries......................................12
Switching to the pedaling monitor mode...................................15
Switch to dual power meter mode ................................................19
Switch to single power meter mode......................................... 23
Pairing /Calibration
Pairing with the Cyclocomputer................................................ 24
Calibrating the sensors (zero point calibration)........................ 26
Specifications and support
Troubleshooting........................................................................ 28
Specifications............................................................................31
Care, Maintenance, and Storage............................................. 32
This product is ANT+™ certified.
Visit http://www.thisisant.com/directory/
for a list of compatible products and apps.
Page: 2
3
EN
Introduction
Features
This product is a sensor system that analyzes the pedaling of a bicycle in real
time. It calculates the direction and intensity of the force acting on the pedals
and calculates pedaling efficiency.
Description of components
•	 Strain gauge unit :
Detects the strain on the crank and calculates the direction and intensity of the
force on the crank.
•	 Magnet:
Used to detect the angle of rotation.
•	 Transmitters:
Send information from the strain gauge unit and the magnet to the
Cyclocomputer.
Product mode
•	 When using SGX-CA500, the firmware version is required to be 20150501.02.43 or
higher.
•	 Pedaling monitor mode:
When paired with Cyclocomputer SGX-CA500, the pedaling efficiency and
cadence and other such properties can be measured. You can make maximum
use of the functions of this product.
•	 Dual power meter mode:
Left and right sensors are required. The actual power values of the left and right
sensors can be totaled and displayed and the cadence can be measured. Can be
used with SGX-CA500 or with a Cyclocomputer that supports ANT+ from another
manufacturer.
•	 Single power meter mode:
The power value of the left or right sensors can be doubled and displayed quickly
and the cadence can be measured. Can be used with SGX-CA500 or with a
Cyclocomputer that supports ANT+ from another manufacturer.
Page: 3
4
EN
Introduction

Switching modes
•	 When using SGX-CA500, the firmware version is required to be 20150501.02.43 or
higher.
•	 Pedaling monitor mode (Page 15)
Can be switched with SGX-CA500. Cannot be switched with cyclocomputers from
other manufacturers. When the mode is switched to pedaling mode, the LEDs on the
sensors light green for 10 seconds.
Current mode
Method 1
(Right sensor push switch)
Method 2
(SGX-CA500)
LED
lighting
method
Dual power meter Cannot be switched ○ The LEDs light
green for 10
seconds
Single power meter Cannot be switched ○
•	 Dual power meter mode (Page 19)
The mode can be switched on SGX-CA500 or by operating the right sensor push
switch. When using with another manufacturer’s Cyclocomputer, switch using
method 1. When the mode is switched to powermeter mode, the LEDs light orange
for 10 seconds.
Current mode
Method 1
(Right sensor push switch)
Method 2
(SGX-CA500)
LED
lighting
method
Pedaling monitor Cannot be switched ○ The LEDs light
orange for 10
seconds
Single power meter ○ ○
Page: 4
5
EN
Introduction

•	 Single power meter mode (Page 23)
SGX-CA500 is required to switch from pedaling monitor mode. Cannot be switched
with cyclocomputers from other manufacturers. To switch from the dual power meter
mode, use SGX-CA500 or press the push switch of the right sensor. When the mode
is switched, the LEDs on the sensors blink orange for 10 seconds.
Current mode
Method 1
(Right sensor push switch)
Method 2
(SGX-CA500)
LED
lighting
method
Pedaling monitor Cannot be switched ○ The LEDs blink
orange for 10
seconds
Dual power meter ○ ○
Manuals
The product’s manuals consist of this User’s Manual, Support Pages, and
Important Information for the User.
•	 User’s Manual (this document)
Explains how to switch the modes of the product, and how to pair the product
with the Cyclocomputer and calibrate the sensors.
•	 Support pages (WEB site)
http://pioneer-cyclesports.com/us-en/support/products/
Explains details about handling methods. How to detach the product (for
dealers) is also described in the references.
•	 Important Information for the User
Important Information for the User provides detailed information related to
safety.
Page: 5
6
EN
Introduction
Compatibility
Crank set
This product supports the following crank sets.
Crank set Remarks
SHIMANO FC-9000 Supports 165 / 167.5 / 170 / 172.5 / 175 / 177.5 / 180 mm crank length,
and 50-34T / 52-36T / 52-38T / 53-39T / 54-42T / 55-42T crank sets. *
SHIMANO FC-6800 Supports 165 / 170 / 172.5 / 175 mm crank length and 50-34T / 52-36T /
53-39T crank sets. *
*	 This manual explains the crank set of 170 mm length with examples.
•	 When replacing the chain ring, be careful not to disconnect the junction cable of the right
pedaling monitor sensor. See the video on how to remove the chain ring first on
http://pioneer-cyclesports.com/us-en/support/products/ to confirm the procedure.
Special skills and tools are needed for the installation and calibration of the
product. To install and calibrate, always ask the shop from where you bought the
product to do it.
Since the product is attached to the crank set with an adhesive, it cannot be
removed without destroying the sensor.
Page: 6
7
EN
Getting
Started
SGY-PM910H2
This product contains the following parts.
Pedaling monitor sensor (left side)
Pedaling monitor sensor (right side)
Product Configuration
① Left transmitter
② Strain gauge unit
③ LED
④ Device Number
Pedaling monitor sensor part (left side)
① Right transmitter
② Junction cable
③ Strain gauge unit
④ Junction box
⑤ Device Number
(Described on the back)
Pedaling monitor sensor part (right side)
Page: 7
8
EN
Getting
Started
Product Configuration
Magnet
Patch type x 2 Arm type (right side) Arm type (left side)
Others
•	 User’s Manual (this document)
•	 Warranty Card
•	 Batteries (CR2032) x 2 (preinstalled in the sensors)
•	 Right transmitter cover (metallic gray)
•	 Hex screws (M2.6 x 8 mm) x 3 (for the right transmitter x 3)
•	 Hex screws (M2.6 x 5 mm) x 3 (spare for the right transmitter cover x 3)
•	 Cable ties x 10 (for the left magnet x 2, for the right magnet x 2, spare x 6)
•	 Cushions for the arm type magnet installation x 2
•	 Patch type magnet base × 2
•	 Tape for installing the chain ring adapter
•	 Tape for installing the FC-6800 adapter base
For FC-9000 Chain ring Adapter
For FC-6800
Adapter base
For FC-6800
Strain gauge unit cover x 1
for each type
Page: 8
9
EN
Getting
Started
Product Configuration
SGY-PM910HL
This product contains the following parts.
Pedaling monitor sensor (left side)
Magnet
Patch type Arm type (left side)
Others
•	 User’s Manual (this document)
•	 Warranty Card
•	 Batteries (CR2032) (preinstalled in the sensor)
•	 Cable ties x 4 (for the left magnet x 2, spare x 2)
•	 Cushions for the arm type magnet installation
•	 Patch type magnet base
① Left transmitter
② Strain gauge unit
③ LED
④ Device Number
Pedaling monitor sensor part (left side)
Page: 9
10
EN
Getting
Started
Product Configuration
SGY-PM910HR
This product contains the following parts.
Pedaling monitor sensor (right side)
For FC-9000 For FC-6800
Strain gauge unit cover x 1
for each type
Chain ring Adapter
For FC-6800
Adapter base
① Right transmitter
② Junction cable
③ Strain gauge unit
④ Junction box
⑤ Device Number
(Described on the back)
Pedaling monitor sensor part (right side)
Page: 10
11
EN
Getting
Started
Product Configuration
Magnet
Patch type Arm type (right side)
Others
•	 User’s Manual (this document)
•	 Warranty Card
•	 Batteries (CR2032) (preinstalled in the sensor)
•	 Right transmitter cover (metallic gray)
•	 Hex screws (M2.6 x 8 mm) x 3 (for the right transmitter x 3)
•	 Hex screws (M2.6 x 5 mm) x 3 (spare for the right transmitter cover x 3)
•	 Cable ties x 4 (for the right magnet x 2, spare x 2)
•	 Cushions for the arm type magnet installation
•	 Patch type magnet base
•	 Tape for installing the chain ring adapter
•	 Tape for installing the FC-6800 adapter base
Page: 11
12
EN
Getting
Started
Installing and Removing the Batteries
The batteries are pre-installed to this product. If the batteries are almost
empty (see Page 28 for how to confirm), replace the batteries with new ones
by the following procedure.
•	 Replace the batteries of both the left and right sensors at the same time.
1.	Remove the cover.
•	 Be careful not to drop or lose the
battery when removing the cover.
•	 Right transmitter (screws: 3 x)
Use a hex wrench (2 mm) to loosen
the screw and remove the cover.
•	 Be careful not to lose the removed
screw.
•	 Do not lose the water-proof packing.
•	 Left transmitter
Turn the cover to the left so the
triangular arrow points to [OPEN]
and remove it.
Page: 12
13
EN
Getting
Started
Installing and Removing the Batteries
2.	Remove the old battery.
•	 Right transmitter
•	 Left transmitter
3.	Install the new battery
(CR2032).
•	 Right transmitter
•	 Left transmitter
After installing the battery, place
the cover with the triangular arrow
pointing to [OPEN], and turn it with
coin to [CLOSE].
•	 Be careful not to drop or lose the
battery when installing it.
•	 Do not lose the water-proof packing.
•	 Do not use batteries other than
CR2032. It can cause malfunction.
•	 Install the cover firmly to ensure
water resistant performance.
•	 Use a dry cotton swab to wipe the
battery terminal in the transmitter
taking care not to deform the
terminal. Clean the terminal regularly
to ensure that the transmitter
operates steadily.
Page: 13
14
EN
Getting
Started
Installing and Removing the Batteries
4.	Check the LED display.
The transmitter starts when the
batteries are installed. The LEDs of the
transmitters light as follows depending
on the actual sensor mode.
•	 When it is in pedaling monitor
mode:	
The LEDs light green for 10
seconds
•	 When it is in dual power meter
mode:
The LEDs light orange for 10
seconds
•	 When it is in single power meter
mode:
The LEDs blink orange for 10
seconds
•	 If the LEDs do not light for more
than 5 seconds after installing the
batteries, remove the batteries
once, and after more than 1 minute,
install them again. If the LEDs still
do not light, the battery may be
almost empty. Replace the battery
with a new one. Dispose of useless
batteries as instructed by the local
government.
5.	Install the right transmitter
cover and tighten the screws
to fix it in place.
While tightening the screws, do not
use excessive force or over-tighten
them. The plastic cover can crack if
you do so. Use a tool that can measure
the torque to tighten the screws.
•	 Tightening torque: 30 cN·m
•	 Install the transmitter cover and
screw the screws in firmly to ensure
water resistant performance.
Push switch
LED
Water-proof
packing
Page: 14
15
EN
Getting
Started
Switching to the pedaling monitor mode
1.	Press the menu button on
the CycloMeter screen of
SGX-CA500.
2.	Tap [Option] - [Pedaling
settings] - [Mode Switch] in
this order.
The mode switching screen opens.
If the device number is already
displayed, confirm that it is the same
as the device number of the sensor
you want to use. If it is the same, the
input operation is not required.
If the device number is different from
the sensor you want to use, enter the
new number.
Remove the check from the sensors
whose mode is not to be switched.
3.	Tap on the device number
display part.
The sensor device number input
screen opens.
•	 Cyclocomputer SGX-CA500 is required to switch to the pedaling monitor mode. The
mode cannot be switched with cyclocomputers from other manufacturers.
•	 The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of
a different version, update the firmware. Refer to the User's Guide (For WEB) of SGX-
CA500 regarding how to update or any other operation method.
http://pioneer-cyclesports.com/us-en/support/products/
Page: 15
16
EN
Getting
Started
Switching to the pedaling monitor mode
4.	Enter the device number and
tap [ ].
The device numbers are printed on
the right junction box and on the side
of the left sensor. (Page 7)
5.	Rotate the bicycle’s crank
set more than three rotations
to start the left and right
transmitters.
•	 Pair with the Cyclocomputer within
5 minutes after the transmitters are
activated.
6.	Tap [Pedaling Monitor].
The search for the sensor starts. A
[Please wait.] message appears.
•	 It may take more than 1 minute to to
pair with the sensor.
The mode switching completion
screen opens. Tap OK if you want to
add in the sensor list.
Page: 16
17
EN
Getting
Started
Switching to the pedaling monitor mode
•	 [Success]
Mode is switched.
•	 [Timeout]
Sensor is not found.
•	 [Cancel]
Cancel is pressed.
•	 [Low Battery]
The battery is almost empty.
•	 Timeout: Communication status is
likely to be poor. Sensor information
cannot be received properly. Make
sure that the sensor you are pairing
is activated, then bring the SGX-
CA500 closer to the sensor and
perform the pairing operation again.
Pairing with the sensor may not be
possible due to interference in the
same frequency band. If “Timeout”
is displayed even by operating
after moving SGX-CA500 closer to
the sensor and pairing with it, try
again someplace where there is no
interference from microwaves, radio
waves, or wireless equipment.
•	 Low Battery: The battery is almost
empty. Remove the battery and
replace with a new one. For how
to install/remove batteries, refer to
Page 12.
If you do not add the sensor in the
sensor list, the SGX-CA500 will not
pair with the sensor.
You can add the sensor in the sensor
list later, using the [Sensors] menu.
When the mode is switched, the
LEDs of the sensors light green for 10
seconds.
Add in the sensor list of SGX-
CA500
When it is added in the sensor list,
it pairs with SGX-CA500. Hereafter,
whenever the sensor is started, it will
automatically pair with SGX-CA500.
To confirm the sensor list, press the
menu button on the left of the product
on the main screen of the CycloMeter
and tap [Sensors]. The display on the
mode switching completion screen is
as follows depending on the status.
Page: 17
18
EN
Getting
Started
Switching to the pedaling monitor mode
Copy pedal
Copy pedal is enabled only in pedaling
monitor mode.
If only the sensor on one side is
operating, you can copy the data on
the other side also to display it for
both sides on the Cyclocomputer and
record it in the log. You can select
copy pedal of the current bike and set
the balance.
1.	Press the menu button on
the CycloMeter screen.
2.	Tap [Option] then [Pedaling
settings] and then [Pedaling
Copy].
3.	Tap [Pedaling Copy], and
select the copy method.
4.	To change the balance, tap
[L:R Balance].
5.	Tap [+], [-] and change the
numerical value and tap [OK].
•	 If you set left and right incorrectly,
note that the correct power will not
be displayed.
Page: 18
19
EN
Getting
Started
Switch to dual power meter mode
•	 Both the left and right sensors are required in this mode. Cyclocomputer SGX-CA500 is
required when the sensor changes to the pedaling monitor mode. It cannot be switched
by using cyclocomputers from other manufacturers.
•	 The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of
a different version, update the firmware. Refer to the User's Guide (For WEB) of SGX-
CA500 regarding how to update.
http://pioneer-cyclesports.com/us-en/support/products/
The mode can be switched in two ways.
[Method 1] Switch by pushing the
push switch in the right transmitter
•	 When using a Cyclocomputer from
another manufacturer, switch with
this method.
1.	Loosen the screws on the
right transmitter cover and
remove the cover.
Refer to Page 12 to remove the right
transmitter cover.
2.	Replacing the batteries of the
left and right transmitters.
Refer to Page 12 regarding how to
install/remove batteries.
•	 The operation is enabled for 5
minutes after the batteries are
installed. Switch within 5 minutes.
If more than 5 minutes elapse, re-
install the batteries of the left and
right sensors.
3.	Confirmation of the actual
sensor mode.
When the batteries are installed, the
LEDs on the left and right transmitters
light as follows depending on the
actual sensor mode.
•	 When it is in pedaling monitor
mode:
The LEDs light green for 10
seconds
•	 When it is in dual power meter
mode:
The LEDs light orange for 10
seconds
•	 When it is in single power meter
mode:
The LEDs blink orange for 10
seconds
Page: 19
20
EN
Getting
Started
Switch to dual power meter mode
4.	Switch the sensor mode.
•	 Before switching the mode, confirm
that there is no other pedaling
monitor near by. If this is not done at
a sufficient distance away from other
sensors, the other sensors are likely
to malfunction.
Push switch
LED
Water-proof
packing
Push for more than
3 seconds
The LEDs blink green
Push for more than
3 seconds
Move away
The LEDs blink orange
rapidly
Confirm that the LEDs
on left and right
transmitters are blinking
The LEDs blink red
The LEDs light orange
Finished
Failure
Page: 20
21
EN
Getting
Started
Switch to dual power meter mode
By pushing the push switch in the right
transmitter for more than 3 seconds,
the LEDs on the right transmitter blink
green. When communication with the
left transmitter is enabled, the LEDs on
the left and right transmitters rapidly
blink orange.
Confirm that the LEDs on the left and
right transmitters blink when the mode
is switched. (If they do not blink, the
communication may have been done
with another pedaling monitor sensor
by mistake. Move somewhere away
from the other bicycles and do the
operation again.)
While the blinking takes place rapidly
for 10 seconds, push the switch
again during that time for more than
3 seconds. The mode is switched to
the dual power meter mode. When
the mode is switched, the LED starts
lighting orange for 10 seconds. If you
do not push long while the LEDs are
rapidly blinking orange , it is canceled
and so, you must do the operation
again.
•	 It may take several seconds to switch
the sensor mode depending on the
radio transmission conditions.
If the pairing with the left transmitter
fails, the LEDs of the right transmitter
blink red 5 times. Since the left
transmitter may be in the pedaling
monitor mode, switch to the
single power meter mode first on
Cyclocomputer SGX-CA500 and do
the above operation. If it still fails,
remove the batteries from the left and
right transmitters, wait for more than
one minute. Place the batteries back
and do the operation again.
After the mode is switched, install the
right transmitter cover and tighten the
screws to fix it in place. Use a tool that
can measure the torque to tighten the
screws.
•	 Tightening torque: 30 cN·m
•	 Install the transmitter cover and
the screws in firmly to ensure water
resistant performance.
•	 Do not lose the water-proof packing.
For how to pair with the cyclocomputer,
when using SGX-CA500, refer to Page
24 and if using a cyclocomputer
from another manufacturer, refer to the
User's Manual of that cyclocomputer.
Page: 21
22
EN
Getting
Started
Switch to dual power meter mode
[Method 2] Switch the mode on SGX-
CA500
Do operations 1 to 5 described on
Page 15 to Page 16 , and go to
the mode switching screen.
1.	If the left and right sensors
are checked, tap [Dual Power].
The mode switching completion screen
opens.
In this state, the cyclocomputer is still
not paired with the sensor. Refer to
Page 24 regarding how to pair.
If the mode cannot be switched, refer
to Add in the sensor list of SGX-CA500
in page 17.
When the mode is switched, the LEDs
of the sensors light orange for 10
seconds.
Page: 22
23
EN
Getting
Started
Switch to single power meter mode
•	 If the actual sensor mode is pedaling monitor mode, switch it on SGX-CA500.
•	 The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of
a different version, update the firmware. Refer to the User's Guide (For WEB) of SGX-
CA500 regarding how to update.
http://pioneer-cyclesports.com/us-en/support/products/
The mode can be switched in two ways. Select according to the actual sensor mode.
[Method 1] Switch by pushing the
push switch in the right transmitter
•	 When using a Cyclocomputer from
another manufacturer, switch with
this method.
•	 When it is in the dual power meter
mode, if the left and right transmitters
are not started, the mode cannot be
switched to the single power meter
mode.
Rotate the crank set of the bicycle and
start the sensor. (Described on Page
16)
When it is in dual power meter mode,
if you push the push switch in the right
transmitter for more than 3 seconds,
the mode changes to single power
meter mode and the LEDs blink orange
for 10 seconds.
When the LEDs blink red, the left
transmitter may not have started. Start
it again.
When the sensor is in pealing monitor
mode, it does not change to the single
power meter mode, even on pushing
the the push switch. Switch using
method 2.
[Method 2] Switch the sensor mode
from SGX-CA500
If the mode is pedaling monitor
mode or dual power meter mode,
switch using the SGX-CA500. Do the
operation as described on Page 15,
and go to the mode switching screen.
Check the sensor you want to use,
then select single power and switch
the mode.
For how to pair with the cyclocomputer,
refer to Page 24. When the mode
is switched, the LEDs of the sensors
blink orange for 10 seconds.
Page: 23
24
EN
Pairing
/Calibration
Pairing with the Cyclocomputer
This section describes how to pair the installed pedaling monitor sensors on
your bicycle to the SGX-CA500 Cyclocomputer.
●
● If you are using this product with a Cyclocomputer from another
manufacturer, the method of pairing is different. Refer to the User’s Manual
of the Cyclocomputer you are using.
1.	Check the sensor modes.
The actual sensor mode can be
confirmed from the way the LEDs of
the sensors light when the batteries
are installed, or from the way the LEDs
light on switching to each mode.
•	 Refer to Page 15 to switch the
modes.
2.	Tap the [Sensors] icon in the
home screen of the SGX-
CA500.
The sensor list screen opens.
3.	Rotate the bicycle’s crank
set more than three rotations
to start the transmitters.
•	 After the transmitters are activated, it
may take more than 1 minute to pair
with the Cyclocomputer.
•	 Pair with the Cyclocomputer within
5 minutes after the transmitters are
activated.
4.	Tap [Connect New] in the
sensor list screen of the
SGX-CA500.
The sensor connection menu opens.
5.	Tap [Device Type] and then
[Pedaling Monitor R].
•	 For the left transmitter, tap [Pedaling
Monitor L].
•	 In single or dual power meter mode,
select the device type.
•	 If multiple sensors are activated,
bring the main unit closer to the
sensor, or specify the device number
to pair the sensor you want to pair.
Refer to the User's Guide (For WEB)
of the Cyclocomputer SGX-CA500
regarding how to specify a device
number to pair a sensor.
Page: 24
25
EN
Pairing
/Calibration
Pairing with the Cyclocomputer
6.	Tap [Search].
The search for the sensor starts.
A [Searching. Please wait.] message
appears.
7.	Check the information about
the sensor.
Information about the sensors appears
when the sensors are found.
Check the following items.
•	 [Device Number]
Make sure that the device number
is the same as the device number
of the transmitter.
•	 [Error Rate]
Make sure that “OK” is displayed.
•	 The device numbers are printed on
the right junction box and on the side
of the left sensor. If the numbers that
are displayed on (Page 7)[Device
Number] are different from the
transmitter device numbers, specify
the device numbers to pair with the
sensor. Refer to the User's Guide
(For WEB) of the Cyclocomputer
SGX-CA500 regarding how to
specify a device number to pair a
sensor.
•	 If “Processing...” is displayed in the
[Error Rate] area, the information
from the sensor is not being received
correctly because transmission
conditions are bad. Make sure
that the sensor you are pairing is
activated, then bring the SGX-CA500
closer to the sensor and perform the
pairing operation again.
•	 Pairing with the sensor may not
be possible due to interference
in the same frequency band. If
“Processing...” is displayed even if
the SGX-CA500 is moved closer
to the sensor and paired with it, try
again someplace where there is no
interference from microwaves, radio
waves, or wireless equipment.
Pairing of the right transmitter is
completed. Pair the left transmitter in
the same way.
Page: 25
26
EN
Pairing
/Calibration
Calibrating the sensors (zero point calibration)
This section describes how to use the Cyclocomputer to calibrate the zero
point of the pedaling monitor sensor that is installed on the bicycle. Zero point
calibration is a function to store the zero point (no-load), where no forces act
on the crank, in the sensor memory. The accuracy of the sensor improves
with repeated implementation.
•	 Zero point calibration should be done by customers whenever the measurement value is
deviating.
•	 The right-side pedaling monitor sensor is used as an example in this description. The
procedure to calibrate the left side is the same as for the right side.
•	 Please do not push the push switch in the right transmitter while calibrating the sensor
with the Cyclocomputer.
Calibration method in pedaling monitor mode using SGX-CA500
Getting Started
1.	Stop the bicycle on a flat
safe place.
Calibrating the Zero Point
1.	Position the crank arm so
it is perpendicular to the
ground, pointing downward.
2.	Tap the [Sensors] icon in the
home screen of the SGX-
CA500.
The sensor list screen opens.
3.	Tap [Pedaling Monitor R] and
then [Calibration (Zero)].
4.	Tap [Start Calibration].
The calibration starts.
If the calibration is successful,
“Success” appears in the [Result] field.
If “Failure” is displayed, the sensor may
be calibrated in an unstable condition
causing the crank to be moving during
the calibration. Calibrate again with the
crank in a stable position.
Page: 26
27
EN
Pairing
/Calibration
Calibrating the sensors (zero point calibration)
•	 This product has a correction function
for the zero point fluctuation caused
by varying temperatures. The
accuracy of this function improves by
calibrating the sensor when there is
a difference in temperature of more
than 4 °C.
This function cannot measure
correctly if you calibrate the sensor
before it is acclimated to the outside
temperature. The sensor requires
more than 20 minutes to become
acclimated.
Checking the Zero Point
1.	Position the crank arm so
it is perpendicular to the
ground, pointing downward.
2.	Tap [Pedaling Monitor R] in
the sensor list screen of the
SGX-CA500.
3.	Confirm the value in [Force
Preview].
Make sure that the [Tangential Force]
and [Radial Force] values are as
shown here.
•	 Tangential Force: 0 ± 3 N
•	 Radial Force: 0 ± 3 N
Calibration of the right side is finished.
Calibrate the left side in the same way.
Calibration method in
power meter mode using a
cyclocomputer from another
manufacturer
For how to calibrate, refer to the User’s
Manual of the cyclocomputer you are
using.
Page: 27
28
EN
Specifications
and
support
Troubleshooting
Refer to the following suggestions if you have any problems installing or using
the product.
If you cannot find what you want to know here, ask the shop where you
bought the product.
■
■ I cannot pair with the Cyclocomputer.
Cause Solution
The battery is almost empty.
(Battery voltage target is 2.5V or
less)
If the LEDs do not light for more than 5 seconds after
installing the batteries, remove the batteries once,
and after more than 1 minute, install them again. If the
LEDs still do not light, the battery may be almost empty.
Replace the battery with a new one.
(+) or (–) side of the battery is
installed in the opposite side.
Install the battery in the proper side (Page 12).
There are other 2.4 GHz wireless
equipment or microwave ovens
near by.
Move away from other wireless equipment or microwave
ovens. Move the sensor closer to the Cyclocomputer and
pair them.
Another sensor is paired with the
Cyclocomputer.
Move away from other sensors by more than 10 m or
specify the device number to pair the Cyclocomputer.
Refer to the Installation Manual (For Web) for details.
http://pioneer-cyclesports.com/us-en/support/products/
Transmitter is not starting. Reinstall the battery of the transmitter or rotate the
bicycle’s crank set more than three rotations to start the
transmitter. The transmitter will start in 5 minutes, so you
must pair in that time.
If the problem is not resolved by the above, confirm
the magnet installation status from the shop where you
bought the product.
Page: 28
29
EN
Specifications
and
support
Troubleshooting
■
■ Unable to switch to pedaling monitor mode.
Cause Solution
You are not using cyclocomputer
SGX-CA500.
You cannot switch to the pedaling monitor mode if you
are using some other manufacturer’s cyclocomputer. Use
SGX-CA500. For how to operate, refer to Page 15.
The version of the firmware of
SGX-CA500 is old.
Update firmware to 20150501.02.43 or to a higher
version.
■
■ Unable to switch to dual power meter mode.
Cause Solution
You are not operating the right
transmitter push switch correctly.
By pushing the push switch in the right transmitter for
more than 3 seconds, the LEDs on the right transmitter
blink green. When communication with the left transmitter
is enabled, the LEDs on the left and right transmitters
rapidly blink orange. As it blinks for 10 seconds, push the
switch again for more than 3 seconds to switch.
More than 5 minutes have elapsed
after the battery was inserted.
To operate by the push switch in the right transmitter,
insert the battery and do the above operation within 5
seconds after that.
You have paired with another
pedaling monitor sensor.
When the LEDs on your left and right transmitters are
not blinking orange, it is likely that they are paired with
another pedaling monitor sensor by mistake. Move
somewhere away from other bicycles and do the above
operation again.
■
■ The power value of the pedaling monitor sensor is abnormal.
Cause Solution
The battery terminal is dirty.
Battery
terminal
Use a dry cotton swab to wipe the battery terminal in the
transmitter taking care not to deform the terminal. Even if
it does not appear to be dirty, white dust may be lodged
in the battery terminal. Clean the terminal as the problem
will be improved if the dust is wiped out. Clean the
terminal regularly to ensure that the transmitter operates
stably.
Page: 29
30
EN
Specifications
and
support
Troubleshooting
■
■ Vector display is strange.
Cause Solution
Magnet is not calibrated. Get the magnet calibrated from the shop where you
purchased the product. Contact with the shop where you
purchased the product.
■
■ Zero point calibration fails.
Cause Solution
The crank is subjected to external
force or moving.
Calibrate the sensor in still condition (Page 26).
■
■ The Cyclocomputer display is not displaying correctly while I am riding.
Cause Solution
Zero point calibration has failed. Calibrate the sensor if the values in [Force Preview] are
more than ± 4N (Page 26).
■
■ There is a rattling noise when I am riding.
Cause Solution
Screws used to install the right
sensor are loose.
Retighten the screws.
■
■ The magnet is rubbing against the sensor or transmitter while I am riding.
Cause Solution
Foreign objects are attached to
the magnet and rub against the
transmitter or the junction box.
Clean the transmitter, junction box, and magnet.
Page: 30
31
EN
Specifications
and
support
Specifications
Weight		 : SGY-PM910H2	 right side + left side About 62 g
		 : SGY-PM910HL	 left side About 22 g
		 : SGY-PM910HR	 right side About 40 g
Dimensions		 : right side
		 • Right transmitter
				 58.3 mm(W) × 46.1 mm(H) × 21.3 mm(D)
		 • Junction box, Strain gauge unit cover
				 78 mm(W) × 36.7 mm(H) × 7.3 mm(D)
		 : left side
				 92.5 mm(W) × 34.7 mm(H) × 8.6 mm(D)
Water resistant		
: This device has a water resistance rating of IPX-6/IPX-7
Communications method (sensors): ANT+ wireless
Batteries		
: CR2032
Operation temperature: –10 °C to 50 °C
•	 ANT+ is a Wireless Personal Network protocol with very low power
requirements using 2.4 GHz frequency band.
For more information, visit http://www.thisisant.com/.
•	 Specifications and design are subject to change without notice.
•	 Illustrations used in this manual may be different from actual appearance.
Page: 31
32
EN
Specifications
and
support
Care, Maintenance, and Storage
Care, Maintenance, and Storage
•	 Use a soft dry cloth or a cloth that has been dampened and wrung out to
wipe dirt from the left and right transmitters, the strain gauge unit cover,
the magnet, and other accessories.
•	 Do not use benzene, paint thinner, or other volatile chemicals, cleansers,
or chemically treated cloths. Doing so could damage the product or
cause the paint to peel off.
•	 If any detergent is lodged in around the body of the sensor, wash it off
properly with water.
•	 If you are not going to use the product for a long period of time, remove
the batteries.
•	 Clean the battery terminal regularly to ensure that the transmitter
operates steadily. (refer to Page 29.)
Page: 233
©2015 PIONEER CORPORATION.
All rights reserved.
<CRD4915-A>
http://www.pioneerelectronics.com
http://www.pioneerelectronics.ca
http://www.pioneer.eu
Visit www.pioneer.eu to register your product.
Visitez www.pioneer.eu pour enregistrer votre appareil.
Si prega di visitare il sito www.pioneer.eu per registrate il prodotto.
Visite www.pioneer.eu para registrar su producto.
Zum Registrieren Ihres Produktes besuchen Sie bitte www.pioneer.eu.
Bezoek www.pioneer.eu om uw product te registreren.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California, 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA INC.
340 Ferrier Street, Unit 2, Markham, Ontario, L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: +32 (0)3 570 05 11
© 2015 PIONEER CORPORATION.
Tous droits de reproduction et de
traduction réservés.

Question & answers

There are no questions about the Pioneer SGY-PM910HL yet.

Ask a question about the Pioneer SGY-PM910HL

Have a question about the Pioneer SGY-PM910HL but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer SGY-PM910HL. Please make sure that you describe your difficulty with the Pioneer SGY-PM910HL as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.