Pioneer SGY-PM68 manual

View a manual of the Pioneer SGY-PM68 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Bicycle Computer
  • Model/name: SGY-PM68
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 1
New Installation Procedure
• A new installation procedure is available for SGY-PM90 and
SGY-PM68 Series cranksets.
• The newest firmware for the SGX-CA500 is required for use with
these cranksets – 2.43
• Compatible cranksets will have an orange sticker on the box and
another on one of the crank arms.
• An updated owners manual will be included in those systems.
• Units not displaying this orange sticker should follow the
installation instructions found in the owners manual provided with
that product.
• The new installation procedure does not provide any
performance enhancements to the product.
• Installation procedures on pages 3 and 4 of this Quick Guide are
for this new procedure.
Page: 2
Easy Installation Power Meter Cranksets
SGY-PM90 and SGY-PM68 with Non-Pioneer ANT+ Cycle Computer
1.) Magnet Placement
• Measuring from the center of the bottom bracket out,
temporarily tape the magnet so that the center line of the
magnet is:
• Right Drive Side - 42mm
• Left Side - 53mm
• Use the supplied Magnet Placement Template to help locate
the optimum locations for magnet placement on the frame.
• Position the magnets so the sensor line and magnet center
line are parallel when the sensor passes over.
Center hole on bottom bracket and use supplied
double sided tape to temporarily secure while locating
optimum magnet location
Sensor Line:
Magnet
Center
Line:
Magnet Range
1.5mm – 10.7mm
Magnet Template
card
2.) Confirm Magnet Placement
• Remove and replace both Left and Right batteries. Orange light will appear for 10 seconds.
• Rotate the crank slowly (30rpm). Check that the LED on each sensor lights green once for each
revolution.
• Once confirmed, secure magnets for final placement. If no Green LED,
check and adjust
magnet placement
LED’s light green
3.) Pair to your ANT+ Computer
• Spin the crank 3 – 4 rotations to activate the Power Meter
See your ANT+ Cycle Computer
Instructions for Power Meter Pairing and
Zero Calibration procedures.
ID 12345
Sensor ID
Left Sensor Arm
For additional Installation Instructions visit the following on-line support
locations
www.pioneerelectronics.com/PUSA/Cycle+Sports/Products/Power+Meters
www.Youtube/Pioneer Cycle Sports USA
Please refer to the owners manual for detailed installation instructions.
Visit https://cyclo-sphere.com/ for the latest firmware and updates.
Customer Support – 1-800-421-1624
E-Mail: cycle-sports@pioneer-usa.com
Page: 3
• Magnet Placement
1. Measuring from the center of the bottom bracket out, temporarily tape the magnet so that the center line
of the magnet is:
• Right Drive Side - 42mm
• Left Side - 53mm
2. Use the supplied Magnet Placement Template to help locate the optimum locations for magnet placement
on the frame.
3. Position the magnets so the sensor line and magnet center line are parallel when the sensor passes over.
Center Magnet Placement Template hole on bottom bracket
and use supplied double sided tape to temporarily secure while
locating optimum magnet location.
Sensor Line:
Magnet
Center
Line:
Magnet Range
1.5mm – 10.7mm
Magnet Template
card
Press Option Press Pedaling Settings Press Pedaling Monitor
Press Menu
• Mode Selection & Pairing to the Pioneer Computer
1. Spin the crank 3 – 4 rotations to activate the Power Meter
2. Pressing Pedaling Monitor will search sensor ID or local crank.
SGX-CA500 firmware must be 20150501.02.43 or higher.
Press OK
ID 12345
Sensor
ID
Left Sensor Arm
• Magnet Calibration
Press Option Press Pedaling Settings
Press Menu
Press Magnet Calibration
Press Start calibration
Spin Crank Slowly
Confirm Sensor locations
5 x per side
1. Spin the crank FORWARD slowly (30 rpm) until both left
and right sensors detect magnets at least 5 times for each
side and press Save.
Press Start Calibration Press OK
2.) Secure magnets for final placement.
For additional Installation Instructions visit the following on-line support
locations
www.pioneerelectronics.com/PUSA/Cycle+Sports/Products/Power+Meters
www.Youtube/Pioneer Cycle Sports USA
Please refer to the owners manual for detailed installation instructions.
Visit https://cyclo-sphere.com/ for the latest firmware and updates.
Customer Support – 1-800-421-1624
E-Mail: cycle-sports@pioneer-usa.com
Press Option Press Pedaling Settings Press Magnet Calibration
Press Menu Press OK
• Zero Calibration – Position Left or Right crank arm to the 6 o’clock position
Easy Installation Power Meter Cranksets
SGY-PM90 and SGY-PM68 with Pioneer Cycle Computer
Page: 4
SGX-CA500
Pairing with a Power Meter
Pioneer Power Meter Other ANT+ Power Meters
Enter device number
listed on side of left
transmitter
Or
Press
Page: 5
SGX-CA500
Zero Calibration
Select
ZeroCal
Point left crank arm
to 6 o’clock
Point right crank arm
to 6 o’clock
Or
You can check zero calibration status
on Cyclo-Sphere in individual ride
analysis under Device Information
• # of times zero calibrated
• Temperatures in memory
Zero Calibration is required to adjust for changes in crank deflection at different temperatures. Pioneer power meters provide 6
temperature memories loaded each time temperature varies 4 degree’s centigrade.
Page: 6
Select up to 16 Layout Options per page
Grey = Graphic or Numerical
White = Numerical Only
Default Pageset 1 for Pioneer
Power Meter use
SGX-CA500
Pageset Select / Pageset Edit
Change Pageset
Edit Pageset 1
Default Pageset 2 for ANT+ /
Other Power Meter
Or
Pageset Select Pageset Edit
Select from 1 – 6 Pages
Grey data fields = Vector & Torque
Graphics
For Pioneer Power Meter
Grey & White data fields =
200 Unique Metrics – All ANT+
Connected Devices
Press and Hold
Page: 7
Wifi Ride Upload
1.) Connect to your WiFi
Network
2.) Create a Cyclo-Sphere Account
With an E-mail and Password
https://cyclo-sphere.com/
3.) Provide your Cycle Computer with your
Cyclo-Sphere E-mail and Password for Auto
Upload
Hold Back Button
to return to the upload section
4.) Charge your Computer before every ride…
Start
Train
n
Race
Stop
Reset
X
3 sec.
Ride data will auto-upload
to Cyclo-Sphere when in
range of your wifi
networks.
You can enter multiple wifi
spots ie., your home,
Starbucks…
Page: 8
Firmware Update
Menu
Cyclo-Sphere will announce new
firmware and provide details of the
updates.
Update Firmware via Wi-Fi
Page: 9
Cyclo-Sphere
How to Use
Cyclo-Sphere
FAQ
Glossary
https://cyclo-sphere.com
Basic E-Mail
and Password
User name…
You’re In!
* Cyclo-Sphere is optimized for Pioneer
Cycle-Sports computers and Power Meters
but works great with any ANT+ Cycle
Computers, Power Meters, Cadence / Speed,
and Heart Rate Sensors.
Page: 10
Quick Return to My Workouts
Calendar Ride Access
Return to Default Layout
Windows can be moved during
analysis
Upload Files
Allows “uploading” of .FIT files stored on your PC for Cyclo-Sphere
analysis and auto-forwarding to Strava
Download Files
Converts Pioneer .db files into .FIT files
and “downloads” them to your PC for
later “upload” to other Cycling analysis
websites ie. Training Peaks, Garmin,
Strava, MapMy Ride, etc.
Search / Files
Page: 11
Change Metric in column
Add Column
Workout List
Page: 12
Create New
Parameter Group
Chart
Edit Groups
Manual FTP Entry
Manual Weight
Entry
Color Coded
Power Zones
Statistics – Ride Group Charts & Graphs
User Created
“Training”
Page: 13
Green = All Rides
Red = Selected Ride
GPS – Maps & Route History
Page: 14
MMP = Mean Maximum Power
For increasing intervals of time
FTP = Max Power Avg. over 1 hour
Select Up to 4 Rides or Ride Groups
To view and compare
Create a Ride or Ride Group for Analysis
and comparison to other groups
MMP – Mean Maximum Power
Page: 15
Ride Summary Laps Segments
Line Graphs
Histogram Scatter Chart
Select Metrics
Pedaling Monitor
Pioneer Power
Meter Only
Pedaling Graph
Pioneer Power
Meter Only
Ride MMP
Vs.
Other
GPS Route
Satellite View
Individual Ride Analysis
Page: 16
Auto “Forward” to STRAVA, Training Peaks, Facebook & Twitter
My Workouts Profile Settings Web Link
Link and Forward to Strava Authorize
Enter Strava Account address
and password.
Strava Ride Analysis
Page: 17
My Workouts
Profile Settings
Web Link
Post Ride Analysis to STRAVA, Training Peaks, Facebook & Twitter
Post a single event
• Select Auto Forward
• Select Private or Public
Auto-Forward
Twitter and Facebook
Page: 18
Make STRAVA Public
Laptop / PC:
Go to Dashboard Activity Feed
Click on your ride
or
Click on the “Edit this Activity” pen Un-Click Private
Strava App:
Click Feed
Click the
date or Map
Click on the lock icon
Click on the
“Edit this Activity” pen
Page: 19
Resources
N. America Site
www.pioneerelectronics.com/PUSA/
www.powerisking.com
https://cyclo-sphere.com/
Facebook
Pioneer Cycle Sports USA
Magnet Calibration Installation Video
http://www.youtube.com/watch?v=w4k
F4Zx1bqk&feature=youtu.be
Global Site:
http://pioneer-cyclesports.com/us-en/
Comments and Questions, E-Mail to:
cycle-sports@pioneer-usa.com
Pioneer Customer Service
1 (800) 421-1404

Question & answers

There are no questions about the Pioneer SGY-PM68 yet.

Ask a question about the Pioneer SGY-PM68

Have a question about the Pioneer SGY-PM68 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer SGY-PM68. Please make sure that you describe your difficulty with the Pioneer SGY-PM68 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.