Pioneer PDK-TS25B manual

View a manual of the Pioneer PDK-TS25B below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Pioneer
  • Product: Flat panel support
  • Model/name: PDK-TS25B
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Indonesian

Table of Contents

Page: 11
12
En
Thank you for buying Pioneer’s product.
Please read through the Operating Instructions to learn how
to operate your model safely and properly.
Please be advised to keep the Operating Instructions in
your place for future reference.
Contents
Cautions ................................................................. 12
Checking the Enclosed Parts................................ 13
Support Columns Used / Not Used Table .......... 13
Assembling the Stand .......................................... 14
Attaching the Plasma Display .............................. 15
Forward/Backward Angle of Inclination
Adjustment Mechanism ....................................... 16
Installing the Product on a TV table etc. ............ 17
Preparing the Cables............................................. 18
Preventing Equipment from Falling Over ........... 19
Fixing the rotation to the front ............................ 20
Detaching the Plasma Display from the Stand .... 20
Specifications ........................................................ 20
Dimensions Diagram ............................................ 21
Installation
• Consult your dealer if you encounter any difficulties
with this installation.
• Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
Cautions
This product is a table top stand exclusively designed for
Plasma Displays (PDP-507XD / PDP-427XD / PDP-507XA /
PDP-427XA) from Pioneer.
Use with other model is capable of resulting in instability
causing possible injury. For further information, please
contact the store where you purchased your display.
Do not install or modify the product other than specified.
Do not use this stand for a Plasma Display other than those
designated and do not modify it or use it for other pur-
poses.
Improper installation is extremely dangerous because it
may result in it falling over or other accident.
Installation Location
• Select a location that is strong enough to support the
weight of the stand and the displays.
• Make sure to place it in a level and stable location.
• Do not install it outdoors or in a wet place such as at a
hot spring or near a beach.
• Do not install the stand where it may be subjected to
vibration or shock.
Assembling and Installation
• Assemble the stand in accordance with the assembly
instructions and securely attach all screws at the
designated locations.
There have been cases where unforeseen accidents
such as the equipment breaking or falling over
occurred after the installation of the display because
the stand was not installed as instructed.
• The display must always be installed by two or more
people to assure it is installed safely.
• Before installation, turn off the power for the display
and peripheral devices then remove the power cord
plug from the power outlet.
This product rotates 10° to the left and right and inclines
approximately 2° forward and backward.
Do not place objects within the range of rotation of this
product and the Plasma Display. Install this product so that
during routine use or when it is rotated, it does not protrude
from the TV table or other location it has been installed.
Failure to do so could cause unforeseen accidents such as
the equipment breaking or falling over (see page 17).
While adjusting its angle forward and backward, be
extremely careful to keep your hands out of the space
between the bottom of the plasma display and the stand
(see page 16).
Prevent accidents caused by the product falling over, by
taking reliable measures to prevent it from falling over (see
page 19).
CAUTION
This symbol refers to a hazard or unsafe practice which
can result in personal injury or property damage.
IMPORTANT NOTICE – RECORD THE MODEL NUMBER
AND SERIAL NUMBERS OF THIS EQUIPMENT BELOW.
MODEL NO.
SERIAL NO.
KEEP THESE NUMBERS FOR FUTURE USE.
Page: 12
13
En
English
• Table top stand x 1
• Support columns S x 2 [short columns]
* For PDP-507XD/507XA(except under
speaker models)
* For PDP-427XD/427XA
• Support columns L x 2 [long columns]
* For PDP-507XD/507XA(under speaker
models)
• Cable binders x 2
• Installation screws 1 (M8 x 16 mm: silver) x 4
[used to anchor the support columns and the table top stand]
• Installation screws 2
(M8 x 30 mm: silver) x 2
• Installation screws 3
(M8 x 40 mm: black) x 2
* For PDP-507XD/507XA
• Hexagonal wrench x 1
(Diagonal size: 6 mm)
• Operating instructions
(this document) x 1
• C wrench x 1 (10 mm)
Checking the Enclosed Parts
Check to make sure that you have all the enclosed parts before assembly and installation.
Support Columns Used / Not Used Table
The support columns of this stand vary depending on the Plasma Display and speakers you have purchased.
Please select the support columns according to the following table.
Product you purchased
Your home
region Speaker
Plasma Display
Support columns S
(short columns)
Support columns L
(long columns)
Installation screws 3
(M8 x 40 mm: black)
Installation screws 4
(M8 x 60 mm: silver)
PDP-507HX
Recommended *Can be used
Cannot be used Used Used
Not used
Not used
Used
Recommended *Can be used Used
Not used
Recommended *Can be used Used
Not used
Recommended *Can be used Not used
Recommended *Can be used Not used
Used
Recommended *Can be used Used
Not used
Cannot be used Not used
Used Used
Cannot be used Not used
Used Used
PDP-427HX/427HXD
PDP-507XD/507XA
under speaker models
under speaker models
under speaker models
PDP-427XD/427XA
50 inch model
42 inch model
Japan
Europe
Other than
Japan,
North
America, and
Europe
except under speaker models
except under speaker models
except under speaker models
Built-in speaker type
Built-in speaker type
Built-in speaker type
Used
*: Can be used when the screen is located in a high position.
• Installation screws 4
(M8 x 60 mm: silver) x 2
* For PDP-427XD/427XA
Page: 13
14
En
Support column used:
support column L
(long columns)
Assembling the Stand
2 Secure the support column to the stand
with the Installation screws 1 (4 locations
on the left and right).
Using the enclosed hexagonal wrench, first loosely
attach the top attachment screw, then loosely attach
the bottom attachment screw.
Installation screws 1
(M8 x 16 mm: silver)
Fully tighten the attachment screws.
3 Fully tighten the Installation screws
(4 locations on the left and right).
W
W
W
W
W
T
W
T
Support column used:
support column S
(short columns)
Note
 Always assemble it on a flat table etc.
 Insert the screws in the holes vertically and do not tighten
them with more force than necessary.
Assembly Procedure
1 Select the support columns to attach.
Select the support columns according to the plasma
display that you have purchased (Only one type of the
two types of available support columns should be used).
When the plasma display you have purchased is
PDP-507XD/507XA(under speaker models).
[Support column used: support column L (long
columns)]
When the plasma display you have purchased is
PDP-507XD/507XA(except under speaker models)/
PDP-427XD/427XA.
[Support column used: support column S (short
columns)]
The larger holes
are on the front.
Note
Be sure to carefully store the unused support columns, the
hexagonal wrench, the C wrench, and the Operating
Instructions together.
The weight of a 50 inch Plasma Display(without
speaker) is about 34.1 kg (75.2 lbs), that of a 42 inch
model is about 29.0 kg (63.9 lbs), they have no
depth, and are unstable. Therefore, at least two
people must assemble and install them.
Note
 Be sure to install it on a flat stable location.
 Insert the screws in the holes vertically and do not tighten
them with more force than necessary.
 Make sure that you install the support columns reliably
with reference to the procedure in “Assembling the
Stand”.
Caution
Page: 14
15
En
English
W
W
W
W
W
T
W
T
Installation screws 2
(M8 x 30 mm: silver)
Attaching the Plasma Display
Attachment Method
1 Attaching the Plasma Display to the stand.
Fit the stand’s support columns to the bottom of the
Plasma Display as indicated by the arrows, then slowly
insert them vertically. Be extremely careful not to insert the
support columns of the stand into any part of the Plasma
Display other than the stand insertion slots. Note that doing
so might damage the Plasma Display panel or its ports or
result in the warping of the stand.
Line up the column
supports with the bottom
of the Plasma Display as
indicated in the accompa-
nying diagram.
2 Securing the Plasma Display with
Installation screws 2.
Secure them using the enclosed hexagonal wrench.
Illustration: PDP-507XD/507XA
Installation screws 2
(M8 x 30 mm: silver)
Illustration: PDP-427XD/427XA
3 Securing the Plasma Display with
Installation screws 3/4.
Attach the Plasma Display at the points marked with
“T” using the enclosed hexagonal wrench.
Installation screws 3 (M8 x 40 mm: black)
4 Attaching the speakers.(PDP-507XD/
507XA)
Refer to the operating instructions for the speaker for
the installation method.
Caution
There have been cases where unforeseen accidents
such as the equipment breaking or falling over
occurred because the stand was installed with
wrong screws.
W
W
W
W
W
T
W
T
Installation screws 4 (M8 x 60 mm: silver)
PDP-507XD/507XA
PDP-427XD/427XA
Page: 15
16
En
On this stand, you can adjust the angle of inclination of the
Plasma Display within a range of approximately 2° forward
or backward according to your preference.
Note
 Be sure to adjust the angle only after you have
attached the Plasma Display.
 Be sure to install it on a flat table or other flat
surface.
 Be sure to hold the top of the Plasma Display
with your hand while adjusting the angle.
Adjustment Procedure
1 Loosen the forward/backward inclination
anchor bolts using the enclosed C wrench
(2 locations on the left and right).
While being sure to hold the top of the Plasma Display
with your hand, loosen the forward/backward
inclination anchor bolts on the left and right sides by
rotating them upwards using the enclosed C wrench.
2 Set the angle you prefer.
Set the angle you prefer by slowly moving the Plasma
Display.
3 Tighten the forward/backward inclination
anchor bolts (2 locations on the left and
right).
Firmly tighten the forward/backward inclination
anchor bolts on the left and right sides by rotating
them downward using the enclosed C wrench.
Be sure to hold the top of the Plasma Display with your
hand until you have fully tightened the bolts.
4 Check once more to make sure that the
forward/backward inclination anchor bolts
are fully tightened.
Forward/Backward Angle of Inclination Adjustment Mechanism
Forward/backward
inclination anchor bolt
Loosening
Forward/backward
inclination anchor bolt
Tightening
*Figure shows the 50 inch display model.
Note
While adjusting the angle, be very careful to keep your
hands out of the place indicated by the arrow on the figure.
Page: 16
17
En
English
10
˚
10
˚
Installing the Product on a TV table etc.
Be sure to observe the following precautions when moving
or installing this product with a Plasma Display into a TV
table or other enclosure.
Precautions when moving
 When moving the product more than a few
meters, first remove the speaker, then remove
the Plasma Display from the stand and move the
speaker, Plasma Display, and stand separately.
 When detaching the Plasma Display from the
stand, be sure to follow the procedure described
in “Detaching the Plasma Display from the
Stand” on page 20.
Precautions when installing in a TV
table or other enclosure
When installing in a TV table or other enclosure, hold
the Plasma Display by the handles located on the rear
of the Plasma Display. If you hold the speakers, they
may be damaged or twisted.
When the plasma display you have purchased is
PDP-507XD/507XA(under speaker models).
Hold the Plasma Display by its handles and from the sides.
Installation precautions
Make sure that you always secure a space at least as large
as that shown in the following diagram in front of and
behind the table top stand.
 If the stand protrudes from the TV table, it could
cause unforeseen accidents such as the equipment
breaking or falling over.
 When rotating, take care not to allow the display
to bump into walls or surrounding objects.
 Range of angle rotation
Caution
Caution
Caution
Protrusion is dangerous.
When the plasma display you have purchased is
PDP-507XD/507XA(except under speaker models)/
PDP-427XD/427XA.
Hold the Plasma Display by its handles and from the
bottom.
under speaker
Min.
10
mm
(13/32
inch)
Plasma Display
TV table
Table top stand
Min.
30
mm
(1-3/16
inch)
Back
Depth
of
the
TV
table
420
mm
(16-9/16
inch)
or
more
recommended
Front
Min. 30 mm
(1-3/16 inch)
Min. 30 mm
(1-3/16 inch)
Page: 17
18
En
Preparing the Cables
Use the enclosed cable binders to bind the cables.
Note
Be very careful not to apply force to the bases of the cables.
Using the cable binders
1 Insert the cable binder through the hole on
the top of the rotating platform of the
stand.
2 Gathering cables and placing them on the
cable binder.
3 Locking the cable binder.
 Removing a cable binder
The lock is released by pushing
the part indicated by the arrow
in the figure.
Cable binder
Page: 18
19
En
English
12mmto15mm
(1/2 to 5/8 inch)
M8
* : 50 inch display model
** : 42 inch display model
120
(4-23/32)
522 (20-9/16)*
460 (18-1/8)**
522 (20-9/16)*
460 (18-1/8)**
24
(31/32)
356
(14-1/16)
Preventing Equipment from Falling Over
Stabilizing on TV table or other loca-
tion
Stabilize the equipment as shown in the diagram using
screws that are available on the market.
Note
A TV table with adequate strength, width and depth
should always be used to support the Plasma Display.
Failure to do so could result in falling over.
To stabilize the Plasma Display on a TV table, use screws
that have a nominal diameter of 6 mm (1/4 inch).
Select the appropriate screws after consulting a profes-
sional installer if necessary.
After installing the stand, be sure to take special care to ensure that the Plasma Display will not fall over.
 Position of table screws: Without speakers
Unit: mm (inch)
Using a wall for stabilization
1 Attaching falling prevention bolts to the
Plasma Display.
2 Using strong cords to stabilize it appropri-
ately and firmly to a wall, pillar, or other
sturdy element.
 Perform this work in the same way on the left and
right sides.
 The length of the cords used must be long enough to
allow the stand to rotate freely.
Note
Use falling prevention bolts,
ropes and fittings that
are available on the market.
Recommended bolts:
Nominal diameter M8
Length 12 mm to 15 mm (1/2 to 5/8 inch)
Min. 20 mm
(13/16 inch)
6
mm
(1/4
inch)
9
mm
to
15
mm
(3/8
to
5/8
inch)
• A table with adequate strength should always be used
to support the Plasma Display. Failure to do so could
result in personal injury and physical damage.
• When installing the Plasma Display, please take the
necessary safety measures to prevent it from falling or
overturning in case of emergencies, such as
earthquakes, or of accidents.
• If you do not take these precautions, the Plasma
Display could fall down and cause injury.
• The screws, hooks and other fittings that you use to
secure the Plasma Display to prevent it from
overturning will vary according to the composition and
thickness of the surface to which it will be attached.
• Select the appropriate screws, hooks and other fittings
after first inspecting the surface carefully to determine
its thickness and composition and after consulting a
professional installer if necessary.
Caution
 Because of the plasma display’s weight, if it could fall down, this can result in injury.
 For safety, be sure to take special care to ensure that the Plasma Display will not fall over.
Fittings
1Falling prevention bolts
2Cords
Page: 19
20
En
Detaching the Plasma Display from the Stand
To remove the Plasma Display from the stand, be sure
to always follow the procedure described below to
prevent accidents.
1 First, confirm that the forward/backward
inclination anchor bolt is securely
tightened.
2 First clear a space on a flat floor etc. where
you can lay the Plasma Display flat, then
lay a sheet to protect it from scratches or
other damage.
3 Remove the speakers.(PDP-507XD/PDP-
507XA )
4 Referring to steps 2 and 3 in “Attaching
the Plasma Display” (Page 15.), remove
the installation screws (4 screws).
Note
Do not remove the screws (M8 x 16 mm: silver) by
procedure 2 in Page 14. The support columns might slip
out of place and fall over.
5 Holding the Plasma Display by its handles
and from the bottom, lift the display verti-
cally.
6 Place the Plasma Display slowly onto the
sheet laid out in step 2 with its screen
facing downwards.
Note
When reattaching the Plasma Display to the stand, be
certain that the left/right support columns are set at the
same angle.
Specifications
External dimensions 577 mm (W) x 305 mm (H) x 380 mm (D) (22-23/32 in. (W) x 12 in.(H) x 14-31/32 in. (D))
[When using the support columns S]
Weight 10.7 kg (23.6 lbs)
• The above specifications and exterior may be modified without prior notice to improve the product.
Caution
Stabilize the equipment as shown in the diagram using
screws that are available on the market.
Note
Use a screw that has a nominal
diameter of M4 and length from
20 mm to 30 mm (13/16 to 1-3/
16 inch) to fix the rotation to
the front. 20mmto30mm
(13/16 to 1-3/16 inch)
M4
7
mm
to
12
mm
(5/16
to
1/2
inch)
Fixing the rotation to the front
Page: 20
21
En
English
50 inch display model (under speaker models)
Dimensions Diagram
Unit: mm (inch)
50 inch display model (except under speaker models)
196
(7-11/16)
380
(14-31/32)
140
(5-17/32)
125
(4-1/8)
23 (29/32)
115 (4-1/2)
767(30-3/16)
1224 (48-3/16)
80
(3-5/32)
577 (22-23/32)
717
(28-1/4)
577 (22-23/32)
380(14-31/32)
1224 (48-3/16)
281
(11-1/32)
80
(3-5/32)
140
(5-17/32)
125
(4-1/8)
23 (29/32)
115 (4-1/2)
795
(31-5/16)
852
(33-17/32)
Page: 21
22
En
Dimensions Diagram
42 inch display model
Published by Pioneer Corporation.
Copyright © 2006 Pioneer Corporation.
All rights reserved.
745
(29-11/32)
1040 (40-15/16)
679
(26-3/4)
104
(4-1/8)
160.5
(6-11/32)
196
(7-11/16)
380
(14-31/32)
23 (29/32)
115 (4-1/2)
80
(3-5/32)
577 (22-23/32)
Page: 88
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
Printed in Japan / Imprimé au Japon <AZR1178-B>
Published by Pioneer Corporation.
Copyright © 2006 Pioneer Corporation.
All rights reserved.

Printed on recycled paper.
Imprimé sur papier recyclé.
Gedruckt auf Recyclingpapier.
Stampato su carta riciclata.
Gedrukt op recycled papier.
Impreso en papel reciclado.

Question & answers

There are no questions about the Pioneer PDK-TS25B yet.

Ask a question about the Pioneer PDK-TS25B

Have a question about the Pioneer PDK-TS25B but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Pioneer PDK-TS25B. Please make sure that you describe your difficulty with the Pioneer PDK-TS25B as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.