Panasonic CQ-D1703N5 manual

View a manual of the Panasonic CQ-D1703N5 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Panasonic
  • Product: Car Radio
  • Model/name: CQ-D1703N5
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 1
2
1
E
N
G
L
I
S
H
CQ-D1703N
Safety Information
Warning
Observe the following warnings when using
this unit.
❑The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this prod-
uct with other battery systems, especially a 24 V DC battery
system.
❑Keep batteries out of reach of infants.
Batteries can be ingested, so keep them out of the reach of
infants. If an infant ingests a battery, please seek immediate
medical attention.
❑Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, con-
sult your dealer or an authorized Panasonic Service Centre.
❑Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑Refer fuse replacement to qualified service person-
nel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
Observe the following warnings when
installing.
❑Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑Never use safety-related components for installa-
tion, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gaso-
line tank, and electric wiring are located. Then open the hole
from outside if possible.
❑Never install the product in a location where it inter-
feres with your field of vision.
❑Never have the power cord branched to supply other
equipment with power.
❑After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑Insulate all exposed wires to prevent short circuit-
ing.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or death.
■ Read the operating instructions for the unit and all other com-
ponents of your car audio system carefully before using the
system. They contain instructions about how to use the sys-
tem in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■ This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material dam-
age.
Caution
Page: 2
3
2
E
N
G
L
I
S
H
CQ-D1703N
Caution
Observe the following cautions when using this
unit.
❑Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑This unit is designed for use exclusively in automobiles.
❑Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑Do not expose the unit to direct sunlight or exces-
sive heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
❑Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
❑Set the volume level to low enough before the AUX
connection is completed.
Failure to observe this, the loud noise may come out and
damage your speakers and your hearing. Direct connection
of the speaker/headphone output of an external device with-
out any attenuator may distort sound or damage the con-
nected external device.
Observe the following cautions when
installing.
❑Refer wiring and installation to qualified service
personnel.
Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.
❑Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
❑Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied
or designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
❑Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑Installation Angle
The product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit can be installed.
Consult your dealer for further details.
❑Wear gloves for safety. Make sure that wiring is
completed before installation.
❑To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling
the battery for the remote control unit.
●Use only specified battery (CR2025).
●Match the polarity of the battery with the (+) and (–) marks
in the battery case.
●Replace dead battery as soon as possible.
●Remove the battery from the remote control unit when not
using it for an extended period of time.
●Insulate the battery (by placing them in a plastic bag or cov-
ering them with vinyl tape) before disposal or storage.
●Dispose of the battery according to the local regulations.
●Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
In case of battery leakage
●Thoroughly wipe the battery liquid off the battery case and
insert new battery.
●If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.
●If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
Warning
For your safety, this system is designed not to see the moving pic-
ture while you are driving.
When connecting this unit to the front monitor (on-dash/in-dash):
¡ Park your car in a safe place and use the parking brake lever
before seeing the moving picture.
¡ For your safety, you must ensure that the connection of the
parking brake lead is correct. (a Page 51)
Warning
When driving please enjoy sound only.
Page: 3
4
3
E
N
G
L
I
S
H
CQ-D1703N
Safety Information (continued)
Label Indications and Their Locations
CAUTION
LASER RADIATION
WHEN OPEN.
DO NOT STARE INTO BEAM.
Caution: This product utilizes a laser.
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation expo-
sure.
Do not take apart this unit or attempt to make any changes
yourself.
This unit is a very intricate device that uses a laser pickup to retrieve
information from the surface of compact discs. The laser is carefully
shielded so that its rays remain inside the cabinet.
Therefore, never try to disassemble the player or alter any of its parts
since you may be exposed to laser rays and dangerous voltages.
CLASS 1 LASER PRODUCT
Caution Label
Deck Ass’y
(In this unit,
upper side)
Laser Product
VAROITUS – LASER-
SÄTEILYVAARA
AVATTAESSA. VARO
ALTISTUMISTA
SÄTEELLE.
FÖRSIKTIGHET –
LASERSTRÅLNING I
ÖPPNAT LÄGE. UNDVIK
ATT UTSÄTTAS FÖR
STRÅLEN.
ADVARSEL – LASER-
STRÅLING. UNNGÅ
EKSPONERING FOR
STRÅLEN VED ÅPNING.
ÇçàåÄçàÖ – ãÄáÖêçéÖ
àáãìóÖçàÖ èêà
éíäêõíàà. àáÅÖÜÄíú
ÇéáÑÖâëíÇàü ãÄáÖêçéÉé
àáãìóÖçàü.
CAUTION - LASER RA-
DIATION WHEN OPEN.
AVOID EXPOSURE TO
BEAM.
VORSICHT - LASER-
STRAHLUNG, WENN
GEÖFFNET. VERMEIDEN
SIE EIN AUSSETZEN
GEGENÜBER DEM
LASERSTRAHL.
ATTENTION –
RAYONNEMENT LASER
SI OUVERT, ÉVITER
TOUTE EXPOSITION AU
FAISCEAU.
ADVARSEL – LASER
UDSENDES NÅR DER
ER ÅBNET. UNDGÅ
UDSÆTTELSE FOR
STRÅLER.
This symbol on the products and/or accompanying documents means that used electrical and elec-
tronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection
points, where they will be accepted on a free of charge basis. Alternatively, in some countries you
may be able to return your products to your local retailer upon the purchase of an equivalent new
product.
Disposing of this product correctly will help to save valuable resources and prevent any potential neg-
ative effects on human health and the environment which could otherwise arise from inappropriate
waste handling. Please contact your local authority for further details of your nearest designated col-
lection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legisla-
tion.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the cor-
rect method of disposal.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
Page: 4
5
4
E
N
G
L
I
S
H
CQ-D1703N
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company. We
know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have
built into it, you too will be proud to be a member of our family.
Power
Connector
(K1HY12YY0001)
Q'ty: 1
Lock Cancel
Plate
Q'ty: 2
Mounting
Bolt
Q'ty: 1
ISO Antenna
Adapter
Q'ty: 1
Mounting
Collar
(YEFX0217263A)
Q'ty: 1
Note:
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their parts numbers are subject to modification without prior notice due to improvements.
¡ Trim Plate and Mounting Collar are mounted on the main unit at shipment.
Removable
Face Plate
Case
(YEFA131839)
Q'ty: 1
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
Remote
Control Unit
(YEFX9995584)
Q'ty: 1
Accessories
Installation kit (YEP0FZ5725)
Battery
(CR2025)
Q'ty: 1
Clip
Connector
Q'ty: 1
Trim Plate
(YEFC05657)
Q'ty: 1
PAN EUROPEAN
GUARANTEE
(Warranty Card)
Q'ty: 1
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
Operating
Instructions
(YEFM285852)
Q'ty: 1
5, ALL
2, ALL
Region number
CQ-D1703N5
CQ-D1703N2
Models
Features
Differences between 2 Models
¡ This operating instruction manual is for 2 models CQ-D1703N2 and CQ-D1703N5. The following table describes the dif-
ferences between 2 models.
2 ALL
5
1 2
5 6
Page: 5
6
5
E
N
G
L
I
S
H
CQ-D1703N
Features
Contents
■ Playback of various moving pictures such as
DivX files
Connection of the optional monitor (CY-VM7203N) allows
users to enjoy DivX files recorded on CD-Rs/RWs and
DVD-Rs/RWs as well as DVD videos and video CDs.
■ MP3/DivX playback recorded on CD-Rs/RWs
or DVD-Rs/RWs
MP3/DivX files recorded on CD-Rs/RWs and DVD-Rs/RWs
can be enjoyed. Up to 1200 tracks of MP3/DivX files can be
saved on 1 piece of DVD-R/RW.
*This unit is not compatible with WMA file.
■ Digital Audio Output
Digital audio output terminal for upgrading to Dolby Digital
and dts surround [Requires separately sold optical cable
(CA-LRD60) and digital surround processor.]
■ SQ (Sound Quality)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
■ The AUX input terminal is equipped on the
front panel.
Your mobile audio player and other devices are con-
nectable to this unit without any difficulty.
■ Private mode (P-MODE)
A different source can be selected between the front and
rear seats. Thus, traffic information can be obtained in the
front seat of a car, while DVD’s audio and visual can be
enjoyed in the rear seat of the same car.
Common
Safety Information .............................................. 2
Accessories ........................................................ 5
Features ............................................................. 6
Contents ............................................................. 6
System Upgrade ................................................ 7
Discs that can be Played Back ............. 8
Preparation (Battery Replacement, TV Type setting,
ACC Setting).............................................................9
General (Main Unit) ........................................... 10
General (Remote Control Unit) ........................ 12
Each source
Radio ................................................................. 14
Radio Data System (RDS) ................................ 16
Before Disc Playback ....................................... 22
CD Player .......................................................... 23
MP3/DivX Player ............................................... 24
DVD/VCD Player ............................................... 26
Advanced Operation for Video Discs (DVD/VCD/DivX) .... 28
OSD (On-Screen Display) ................................ 30
Notes on MP3/DivX .......................................... 32
As needed
Audio Settings (Volume, Bass/Treble, Balance/Fader,
Audio Output Level)................................................ 34
Function Settings (FM Monaural Reception, Local
Tuning, Region (REG) Mode, PTY Language Selection,
Private Mode (P-MODE), External Mute,
ACC Selection)....................................................... 36
User Settings (TV Type, etc.) ............................... 40
Language Code List ......................................... 44
Definition of Terms .......................................... 45
Anti-Theft System ............................................ 46
Fuse ................................................................... 47
Maintenance ..................................................... 47
Notes on Discs ................................................. 47
Installation ........................................................ 48
Wiring ................................................................ 50
Troubleshooting ............................................... 56
Specifications ................................................... 63
Discs that can be Played Back (a Page 8)
Page: 6
7
6
E
N
G
L
I
S
H
CQ-D1703N
System Upgrade
❑Basic System
❑Optional system (Example)
This unit can be combined with other components like
shown below. For more details, refer to the operating
instructions for the connected devices.
Preparation:
¡ The TV standard format (NTSC/PAL) setting of this unit
(“TV Type” a Page 42) should be the same as the input
signal setting (NTSC/PAL) of the monitor to be connect-
ed. Otherwise, pictures appear incorrectly. (Default:
PAL)
CQ-D1703N
Color LCD Display:
CY-VM7203N
External Power Amplifier
(CY-PA2003, etc.)
Color LCD Display: CY-VM7203N
Page: 7
8
7
E
N
G
L
I
S
H
CQ-D1703N
Discs that can be Played Back
❒ About DivX
¡DivX files recorded on CD-Rs/RWs and DVD-Rs/RWs are
playable. Refer to “Notes on MP3/DivX” for further infor-
mation. (a Page 32)
❒ Symbols used on jackets
(Examples of such symbols include)
¡ : Number of subtitle languages
¡ : Number of audio tracks
¡ : Number of angles
The numbers indicate the number of languages, tracks,
angles, etc., recorded on the disc.
Screen size (H:V aspect ratio)
¡ : 4:3 standard size
¡ : Letterbox (a Page 43, 45)
¡ 16:9 wide size
: Playback in letterbox format on a standard
screen (4:3).
: Playback in (pan and scan)
(a Page 43, 45) format on a standard
screen (4:3).
Note:
¡The size of the image that is displayed on the screen
depends on the screen mode (“TV Display” a Page 42),
and on the screen size for the content on the disc.
❒ Region Management Information
This product is designed and manufactured to respond to
the Region Management Information that is recorded on a
DVD disc. If the Region number described on the DVD disc
does not correspond to the Region number of this product,
this product does not play the disc.
*2
The Region number for this product is “2” (for CQ-
D1703N2), “5” (for CQ-D1703N5) or “ALL”.
PAN & SCAN
PS
16:9
LB
16:9
LB
4:3
3
2
2
2 ALL
5
1 2
5 6
Example:
❒ Notes on DVD-Rs/RWs (DVD Video)
¡Do not mix DVD-Video formatted data and other format-
ted data on the same disc.
¡Discs in the video recording (VR) format are
unplayable.
¡Unfinalized discs are unplayable.
¡Use disc-at-once recording for DVD-R DL (double-layer).
¡Some discs are unplayable depending on the disc itself,
device, drive and software that are used for disc recording.
❒ Discs not supported
The following discs are not played back on this product.
¡DVD-Audio ¡DVD-ROM ¡DVD-RAM
¡DVD+R ¡DVD+RW
¡VSD ¡CVD
¡CD-G ¡CD-ROM (except MP3)
¡CD-RW (except MP3/DivX and CD-DA)
¡CD-R (except MP3/DivX and CD-DA)
¡SACD ¡Photo CD ¡CDV
¡Hybrid SACD (except CD-DA)
¡CD-EXTRA (audio-only playback possible)
¡DVDs with a region number other than “2”, “5” or
“ALL”*2
¡Playing back a photo CD disc with this unit could
damage the data that is recorded on the disc.
*1
CD-DA : A general music CD format.
Note:
¡Only discs with logos shown in the “Mark/logo” row of
the table above are playable.
¡About CD-Rs and CD-RWs, refer to “Notes on CD-
Rs/RWs, DVD-Rs/RWs”. (a Page 47)
¡Some copy-protected music CDs are not playable.
¡Even if you play a dts DVD or a dts CD, analog sound can-
not be reproduced. (Only digital output comes out)
LPCM (CD-DA*1
),
MP3
❒ Disc Type
TEXT
Recordable
ReWritable
DISC DVD VCD
(Video CD) CD CD-R/RW
Mark/logo
Disc Size 12 cm / 8 cm
Video
Format NTSC / PAL
Audio
Format
LPCM,
MPEG1,
MPEG2,
Dolby
Digital
LPCM
(CD-DA*1
),
MPEG1,
MPEG2
(SVCD)
Region No. 2, 5, ALL*2
(IEC62107)
Page: 8
9
1
E
N
G
L
I
S
H
CQ-D1703N
8
Preparation
Warning
¡Keep batteries away from children to avoid the risk of
accidents. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡ Remove and dispose of an old battery immediately.
¡ Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡ Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Remote Control Unit
Battery Replacement
q
w
q Remove the battery holder with
the remote control unit placed
on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of the
arrow at the same time.
w Pull it out in the direction of
the arrow using a tough
pointed object.
w
e
w Put a battery in the case with
(+) side facing up.
e Put the case back.
Tough pointed object
Back side
Main Unit
For an ACC-equipped car, select ON. (a Page 38) The
following functions are available. (Default: off)
¡The power is turned on automatically when inserting a
disc.
¡The clock can be displayed even if the power is off.
(a Page 10)
: ACC not equipped
(Default)
: ACC equipped
Caution
¡Be sure to select OFF when your car has no
ACC position in the ignition switch. Failure to
do this could cause the battery to go dead.
ACC Setting
TV Type setting
You can select a TV standard format (NTSC/PAL). Refer to
“Optional system (Example)” (a Page 7) and “TV Type”
(a Page 42).
Note:
¡This unit is not compatible with SECAM format.
Page: 9
10
9
E
N
G
L
I
S
H
CQ-D1703N
General (Main Unit)
Power
Set your car's ignition switch to the ACC or ON position.
ON: Press [SRC/PWR].
OFF: Press and hold [SRC/PWR] for more than 1 sec-
ond.
Clock Display (at Power Off)
When the power of the unit is set to OFF, press [DISP]
(CT) (ACC ON).
(Clock time) (Default)
(Display off)
When the power is set to ON, refer to the description for
each source mode.
Volume
Note:
¡ The volume level can be set independently for each
source. (For radio, one volume setting for AM
(LW/MW), one volume setting for all FMs)
Mute
ON : Press [MUTE].
OFF : Press [MUTE] again.
indicator
SQ (Sound Quality)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
Press and hold [MUTE] (SQ) for more than 1 second to
select the sound type (SQ) as follows:
Note:
¡ If no operation takes place for more than 5 seconds in
the SQ mode, the display returns to the regular mode.
¡ Settings of SQ, bass/treble and volume are influenced
one another. If such an influence causes distortion to
the audio signal, readjust bass/treble or volume.
(a Page 34)
(VOCAL) clear sound:
emphasizes middle tone and slightly
emphasizes treble.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
(FLAT) flat frequency response:
does not emphasize any part. (Default)
Up
Down Default: 18
Setting range: 0 to 40
[DISP] (Display)
(CT)
[SRC/PWR] (Source/power)
Remote control sensor (a Page 12)
[VOLUME]
(SQ) indicator
CD Player mode display (a Page 23)
[MUTE]
(SQ) (Sound Quality)
AUX 1 (AUX 1 in)
From line output of external
sound/audio device (ex.
Silicon-audio player, HDD play-
er, etc.)
[]] [[]
(Hour/minute adjustment)
Page: 10
Source
Press [SRC/PWR] to change the source.
Radio
CD Player
MP3/DivX Player
DVD/VCD Player (VCD disc)
DVD/VCD Player (DVD disc)
AUX1
AUX2
Clock Setting
The 24-hour system is used for the clock.
Note:
¡ Adjust the clock when “NO CT” appears on the screen.
Select the radio AM (LW/MW) mode. (a Page 14)
Frequency
Press and hold [DISP] (CT) for more than 2 seconds.
Hour blinks
Adjust the hour.
[[] : put forward hour.
[]] : put back hour.
Hour entered
Press [DISP] (CT).
Minute blinks
Adjust the minute.
[[] : put forward minute.
[]] : put back minute.
Minute entered
Press [DISP] (CT).
Completed
Note:
¡ When a broadcast of FM Radio Data System is received,
the clock is adjusted automatically by the Clock Time
service. (a Page 16)
(Sound source
connecting to the AUX2
(rear) input terminal)
(Sound source connect-
ing to the AUX1 (front)
input terminal
a Page 10)
(When a DVD data disc
is in the player
a Page 26)
(When a VCD data disc
is in the player
a Page 26)
(When a MP3/DivX data
disc is in the player
a Page 24)
(a Page 23)
(a Page 14)
11
1
E
N
G
L
I
S
H
CQ-D1703N
10
OR
OR
OR
Caution
¡Set the volume level to low enough before the
AUX connection is completed.
Failure to observe this, the loud noise may
come out and damage your speakers and your
hearing.
Page: 11
12
11
E
N
G
L
I
S
H
CQ-D1703N
General (Remote Control Unit)
❑ General
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[MENU]
¡Shows the menu
screen.
[SRC]
¡Toggles power on/off.
¡Selects a source.
[OSD] (On-Screen Display)
¡Displays information about
each source on the screen.
[}] [{]
¡Selects (vertically)
or adjusts an
operation or item.
[]] [[]
¡Selects (horizontally)
or adjusts an opera-
tion or item.
[ENTER]
¡Determines an opera-
tion or item.
[VOL]
¡Adjusts the sound
volume.
[}]
[{]
[]] [[]
[ENTER]
[MUTE]
¡Mutes the sound temporarily.
In this manual, the pictographs shown below are used to indicate compatible types of discs and operating units.
Discs : DVD Video : VCD (Video CD)
: CD : CD-Rs/RWs or DVD-Rs/RWs containing MP3 files
: CD-Rs/RWs or DVD-Rs/RWs containing DivX files
DVD VCD CD MP3 DivX
DivX
DivX
DVD VCD CD MP3
MP3
MP3 DivX
DVD VCD CD
CD
CD MP3 DivX
DVD VCD
VCD
VCD
DVD
DVD
DVD VCD
Page: 12
13
12
E
N
G
L
I
S
H
CQ-D1703N
❑ Discs (DVD/VCD/CD/MP3/DivX)
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[■] (STOP)
¡Stops playback.
[❚❚] (PAUSE)
¡Pause.
[❚❚]
¡Frame to Frame Play.
[B] (PLAY)
¡Playback.
[s] [d]
¡Goes to the beginning.
¡Chapter/track/file selection.
¡Fast forward/fast reverse.
[d]
¡Slow playback.
[RET] (RETURN)
¡Return to the previous display.
¡Input the number again.
¡Displays the video CD’s menu.
[MENU] (TITLE)
¡Displays the DVD menu. (Operations
vary according to the disc.)
¡Displays the Title menu. (Operations
vary according to the disc.)
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
[GRP] (Group) (TRACK) (TITLE/CHAPTER)
¡Direct title/chapter selection.
¡Direct track selection.
¡Direct folder/file selection.
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
[}] [{] []] [[]
¡Selects an operation or item.
[ENTER]
¡Determines an operation or item.
[}] [{]
¡Selects a folder.
¡Folder up/down.
DVD VCD CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
[0] to [9]
¡Selects an item on the menu.
[0] to [9]
¡Direct title/chapter selection.
¡Direct track selection.
¡Direct folder/file selection.
[0] to [9]
¡Sets the language code.
[1] (SUBTITLE)
¡Switches the subtitle language.
[2] (AUDIO)
¡Switches the audio language.
[2] (AUDIO)
¡Switches between stereo and
monaural sound.
[3] (ANGLE)
¡Switches the angle.
[4] (RANDOM)
¡Random play.
[5] (SCAN)
¡Scan play.
[6] (REPEAT)
¡Repeat play.
[0] (DRC)
¡Selects a range of dynamic range
compression.
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD VCD CD
CD
CD
DVD VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
DVD VCD
VCD
VCD
DVD VCD CD MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
DVD VCD CD MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
VCD
VCD CD
CD
CD MP3
MP3
MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
VCD
VCD
Page: 13
14
13
E
N
G
L
I
S
H
CQ-D1703N
q Radio Mode
Press [SRC/PWR] to select the radio mode.
w Band
Press [BAND].
e Tuning
[[]: Higher frequency
[]]: Lower frequency
Press and hold [[] or []] for more than 0.5
seconds, then release it. Seeking will start.
Note:
¡ For tuning in to only stations whose receiving condi-
tions are good in the seeking mode, set LOCAL to ON.
(a Page 36)
¡ For reducing noise when a receiving FM stereo wave is
weak, set FM MONO to ON. (a Page 36)
Display Change
Press [DISP] to change the display as follows.
3AM (LW/MW) 3FM (non RDS)
*Adjust the clock when “NO CT” appears on the screen.
(Clock setting a Page 11)
Radio
Band Preset number
Clock Time (CT)*
Frequency
PS (Programme Service
Name)
Clock Time (CT)*
Frequency
Frequency
[BAND]
(APM: Auto Preset Memory)
Preset Buttons [1] to [6] (Preset station)
[]] [[]
(TUNE)
(Stereo) indicator
[DISP] (Display)
[SRC/PWR] (Source)
Page: 14
15
1
E
N
G
L
I
S
H
CQ-D1703N
14
Auto Preset Memory (APM)
With this operation, stations with good receiving condi-
tions can be automatically stored in the preset memory.
q Select a band. (a Previous page)
w Press and hold [BAND] (APM) for more than 2 sec-
onds.
6 stations with first to 6th highest in signal strength will
be preset to each band.
Once set, the preset stations are sequentially scanned
for 5 seconds each. (scanning)
Note:
¡ To stop scanning, press one of the buttons from [1] to
[6].
¡ Only RDS stations will be saved at default setting (AF
ON). To select non-RDS stations, set AF to
OFF. (a Page 17)
Manual Preset Memory
With this operation, a station can be manually stored in the
preset memory.
q Select a band and frequency. (a Previous page)
w Press and hold one of the preset buttons from [1] to [6]
until the display blinks once.
Station Preset
Up to 6 stations can be stored in each of the FM1, FM2, FM3 and AM (LW/MW) band selections.
Note:
¡ New stations overwrite existing saved stations after these procedures.
Warning
¡To ensure safety, never attempt to preset stations while you are driving.
Preset Station Calling
q Select a band. (a Previous page)
w Press one of the preset buttons from [1] to [6].
Preset number
Page: 15
16
15
E
N
G
L
I
S
H
CQ-D1703N
Radio Data System (RDS)
RDS Basics
Some FM stations are broadcasting added data compatible with RDS. This unit offers convenient functions using such data.
RDS service availability varies with areas. Please understand if RDS service is not available in your area, the following serv-
ice is not available, either. This chapter explains the summary and operation regarding RDS.
The following functions are available when receiving RDS stations.
Programme Service Name (PS)
Display
The name of the station is displayed.
Alternative Frequency (AF)
When reception is poor, an RDS station broadcasting the
same programme is tuned in automatically.
Traffic Programme (TP)
Some RDS FM stations periodically provide a traffic
announcement.
Stations which broadcast the traffic announcement are
called Traffic Programme (TP).
Traffic Announcement (TA)
Radio announcements on traffic conditions.
Clock Time (CT) Service
When receiving an RDS station, the CT service automatical-
ly adjusts the time.
“NO CT” is displayed in areas where CT service is not avail-
able. (a Page 11 for Clock Setting)
Programme Type (PTY) Display
RDS FM stations provide a programme type identification
signal.
Example: news, rock, classical music, etc. (a Page 19)
Programme Identification (PI)
Each programme has its own number. This may be used to
search for another frequency on which the same pro-
gramme is broadcast.
Region (REG)
Each region has its own number. This may be used to
identify the region where the station you are now listening
to is located.
Page: 16
17
16
E
N
G
L
I
S
H
CQ-D1703N
Alternative Frequency (AF)
Alternative Frequency (AF)
Mode
Press and hold [TA] (AF) for more than 2 seconds to
select one of the following AF modes.
AF ON : AF, Best Station Research and PI seek function
are active.
AF OFF : When the AF network of an RDS station is not
required.
: Low level AF operating sen-
sitivity. (Default)
: High level AF operating sen-
sitivity.
: When the AF network of an
RDS station is not required.
Display Change
Press [DISP] to change the display as follows.
Preset Memory (AF ON Setting)
Preset Station Calling (Best Station Research)
AF self-tuning allows you to select a station with good
reception from the same network when the preset tuning is
activated.
For Poor Reception (PI Seek)
If reception becomes poor when tuning in a preset station,
press the same preset number button. The same station
with better reception will be searched for.
Press the same preset number button again to cancel.
Note:
¡ For PI Seek, cancel the TA mode first, then execute PI
Seek.
Frequency
Clock Time
PS (Programme Service Name) (Default)
[TA/AF] (Alternative Frequency)
[DISP] (Display)
indicator
Page: 17
18
17
E
N
G
L
I
S
H
CQ-D1703N
Traffic Announcement (TA)
Some RDS FM stations periodically provide traffic information.
Radio Data System (RDS) (continued)
TA ON/OFF (Default: OFF)
Press [TA/AF] (TA mode) to switch the TA mode on and
off.
The following functions are available when the TA mode is
active.
¡ A TP station is automatically searched for and received
at the instant of toggling the TA mode on if you are
receiving a non-TP station or a TP station with poor
reception.
¡ When executing seek tuning or APM, only TP stations
are selected. (a Page 15 for Auto Preset Memory)
¡ Setting to TA on with the unit in another mode, it will
automatically switch to radio mode and a traffic
announcement is broadcast on the radio when the traf-
fic announcement begins. The traffic announcement
having finished, the unit will return to the previous
mode. (TA standby mode)
Traffic information only (TA mute)
While listening to an FM station which is not currently
broadcasting traffic announcement, turn the [VOLUME]
to the counterclockwise to set the volume to 0. The traffic
announcement will be output at the TA volume level.
[TA/AF] (TA mode/TP (TA) Search)
[VOLUME] indicator
indicator
Page: 18
19
18
E
N
G
L
I
S
H
CQ-D1703N
Programme Type (PTY) Reception
RDS FM stations provide a programme type identification signal. (Example: news, rock, classical music, etc.)
Programme Type (PTY) Mode
Press and hold [DISP] (PTY) for more than 2 seconds to
switch the PTY display mode on and off.
The PTY function described below becomes enabled after
selecting to the PTY mode.
PTY Selection
q Press [[] to change the programme type as shown
below. ([]]: opposite direction)
w Select a desired programme type and press [BAND].
Search will start to tune in to a station broadcasting the
selected programme type.
Press [BAND] again to cancel.
Note:
¡ When there is no corresponding programme type sta-
tion, “NONE” is displayed for 2 seconds.
PTY Preset
PTY Preset Call
Programme types are stored in memory under preset but-
tons from [1] to [6] as shown in the table on the next
page.
To tune in a desired programme type, press any of preset
buttons from [1] to [6].
Preset PTY Search
q Select a programme type by pressing the preset button.
The preset programme type appears on the display for 5
seconds.
Example: Press preset button [1].
w Press the same preset button again (or press [BAND])
to tune in the desired programme type station.
Example: Press preset button [1] again.
Press [BAND] again to cancel.
Note:
¡ When there is no corresponding programme type sta-
tion, “NONE” is displayed for 2 seconds.
PTY Preset Change
q Select a programme type by using PTY Selection or
pressing PTY Preset buttons.
w Press and hold one of the buttons from [1] to [6] for
more than 2 seconds.
Example: Press and hold preset button [2] for more
than 2 seconds.
SPEECH / MUSIC / NEWS / AFFAIRS /
INFO / SPORT / EDUCATE / DRAMA /
CULTURE / SCIENCE / VARIED / POP_M /
ROCK_M / EASY_M / LIGHT_M / CLASSICS /
OTHER_M / WEATHER/ FINANCE / CHILDREN /
SOCIAL / RELIGION/ PHONE_IN / TRAVEL /
LEISURE / JAZZ / COUNTRY / NATION_M /
OLDIES / FOLK_M / DOCUMENT
[DISP] (PTY) (PTY Mode)
[]] [[]
(PTY selection)
[BAND]
(Preset PTY search, PTY
selection)
Preset Buttons [1] to [6] (PTY Preset)
indicator
Page: 19
20
19
E
N
G
L
I
S
H
CQ-D1703N
PTY Preset (Default)
Preset No. Programme Type When PTY search is activated, these programme types are receivable.
1 NEWS NEWS
2 SPEECH AFFAIRS, INFO, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED,
WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE_IN,
TRAVEL, LEISURE, DOCUMENT
3 SPORT SPORT
4 POP_M POP_M
5 CLASSICS CLASSICS
6 MUSIC ROCK_M, EASY_M, LIGHT_M, OTHER_M, JAZZ, COUNTRY, NATION_M,
OLDIES, FOLK_M
Radio Data System (RDS) (continued)
Programme Type (PTY) Reception(continued)
Other PTY functions
PTY Language Selection: The language displayed on the screen is selectable. (English or Swedish) (a Page 36)
Page: 20
21
20
E
N
G
L
I
S
H
CQ-D1703N
Enhanced Other Network (EON)
When EON data is received, the EON indicator lights and
the TA and AF functions are expanded as follows.
TA: Traffic information from the current and other network
stations can be received.
AF: The frequency list of preset RDS stations is updated
by EON data.
EON enables the radio to make fuller use of RDS informa-
tion. It constantly updates the AF list of preset stations,
including the one that is currently tuned in to. For exam-
ple, if you preset a station far from home, you will later be
able to receive the same station at an alternative frequency,
or another station serving the same programme. EON also
keeps track of locally available TP stations for quick recep-
tion.
Emergency Announcement
Reception
When an emergency announcement is broadcast, the unit
is automatically switched to receiving the broadcast even if
a source other than radio is selected. During receiving the
emergency announcement, “ALARM” appears on the dis-
play.
Note:
¡ Emergency announcements are broadcast at the TA vol-
ume level (a Page 18). Use caution not to decrease the
TA volume excessively.
Other RDS functions
indicator
Page: 21
22
1
E
N
G
L
I
S
H
CQ-D1703N
21
E
N
G
L
I
S
H
Before Disc Playback
Caution
¡ Do not insert a disc when indicator
lights because a disc is already loaded.
¡ Do not use irregularly shaped discs.
¡ Do not use discs that have a seal or label attached.
¡ Do not insert foreign objects into the disc slot.
Note:
¡ Refer to “Discs that can be Played Back”. (a Page 8)
¡ Refer to the section on “Notes on MP3/DivX” (a Page
32) and “Notes on Discs” (a Page 47).
¡ The power will be turned on automatically when a disc
is loaded. (ACC ON)
¡ A disc which has both CD-DA data and MP3/DivX data
on it may not be played back normally.
OSD (On-Screen Display)
(Only for remote control unit)
You can set up the optional monitor (CY-VM7203N) to dis-
play or hide the information on the disc.
Press [OSD] to switch the OSD text displays. (a Page 30)
Disc Insert
Note:
¡ It may take some time to start playing.
¡ Playback will start automatically after recognizing the
data of the loaded disc.
OR
(a Page 24 about MP3/DivX Player)
OR
(a Page 26 about DVD/VCD Player)
OR
(a Page 26 about DVD/VCD Player)
Disc Eject
Press [u].
Printed Side
Page: 22
23
1
E
N
G
L
I
S
H
CQ-D1703N
When CD is in the player
Press [SRC/PWR] to select the CD player mode and play-
back starts.
Display Change
Press [DISP].
Track/Play time
Disc title
Track title
Clock time
Note:
¡ “NO TEXT” is displayed when there is no information on
the disc.
¡ To have another circle scroll while a title is displayed,
press [3] (SCROLL).
Track Selection
[d]: Next track
[s]: Beginning of the current track
For the previous track, press twice.
Fast Forward/Fast Reverse
Press and hold for more than 0.5 seconds.
Each time you press the button, the speed changes as follows.
Regular speed /2 times /5 times /10 times /20 times
[d] (f): Fast forward
[s] (a): Fast reverse
Press [BAND] (y / 5) to cancel.
Pause (y / 5)
Press [BAND] (y / 5).
Press [BAND] (y / 5) again to cancel.
Random Play
All the available tracks are played in a random sequence.
Press [4] (RANDOM).
lights.
Press [4] (RANDOM) again to cancel.
Scan Play
The first 10 seconds of each track is played in sequence.
Press [5] (SCAN).
Press [5] (SCAN) again to cancel.
Repeat Play
The current track is repeated.
Press [6] (REPEAT).
lights.
Press [6] (REPEAT) again to cancel.
Direct Track Selection
(Only for remote control unit)
Example: Track number 10
q Press [GRP].
w Press [1] [0]. (Press [RET] to cancel.)
e Press [ENTER].
Note:
¡ To suspend direct selection, press [DISP].
¡ Random, Scan and Repeat plays are canceled once
[ENTER] is pressed.
22
CD Player
Track Play time
[BAND]
(y / 5: Pause/play)
[DISP] (Display)
[SRC/PWR] (Source)
[s] / [d] (a / f)
(Track selection/fast for-
ward/fast reverse)
[3] (SCROLL)
[4] (RANDOM)
[5] (SCAN)
[6] (REPEAT)
indicator
indicator
Page: 23
Note:
¡ This unit is not compatible with WMA file.
¡ Refer to “Notes on MP3/DivX” (a Page 32).
When a disc is in the player
Press [SRC/PWR] to select the MP3/DivX player mode
and playback starts.
Display Change
Press [DISP].
Note:
¡ “NO TEXT” is displayed when there is no information on
the disc.
¡ To have another circle scroll while a title is displayed,
press [3] (SCROLL).
Folder Selection
[}]: Next folder
[{]: Previous folder
File Selection
[d]: Next file
[s]: Beginning of the current file
For the previous file, press twice.
Fast Forward/Fast Reverse
Press and hold for more than 0.5 seconds.
The speeds of fast forward and fast reverse change incre-
mentally in 4 steps every time the corresponding button is
pressed.
[d] (f): Fast forward
[s] (a): Fast reverse
Press [BAND] (y / 5) to cancel.
Note:
¡ The speeds of fast forward and fast reverse vary with
the file type, file specifications, and other factors.
Pause (y / 5)
Press [BAND] (y / 5).
Press [BAND] (y / 5) again to cancel.
File name
( ) (Data reading)
24
23
E
N
G
L
I
S
H
CQ-D1703N
Play time
Folder name
( ) (Data reading)
Clock time
MP3/DivX Player
The optional monitor (CY-VM7203N) is necessary to be connected to see images of DivX files.
Folder File
Album name
( ) (Data reading)
Title and Artist name
( ) (Data reading)
Folder/File
[DISP] (Display)
[SRC/PWR] (Source)
[3] (SCROLL)
[4] (RANDOM)
[6] (REPEAT)
[s] / [d] (a / f)
(File selection/fast
forward/fast reverse)
[{] / [}] (FOLDER)
(Folder selection)
[BAND] (y / 5: Pause/play)
indicator
indicator indicator
(only for MP3 files)
Page: 24
25
1
E
N
G
L
I
S
H
CQ-D1703N
24
Random Play
All the available files are played in a random sequence.
Press [4] (RANDOM).
lights.
Press [4] (RANDOM) again to cancel.
Folder Random Play
All the files in the current folder are played in a random
sequence.
Press and hold [4] (RANDOM) for more than 2 seconds.
light.
Press and hold [4] (RANDOM) again for more than 2
seconds to cancel.
Repeat Play
The current file is repeated.
Press [6] (REPEAT).
lights.
Press [6] (REPEAT) again to cancel.
Folder Repeat Play
The current folder is repeated.
Press and hold [6] (REPEAT) for more than 2 seconds.
light.
Press and hold [6] (REPEAT) again for more than 2 sec-
onds to cancel.
Direct Selection
(Only for remote control)
Direct Folder Selection
Example: Folder number 10 (a Page 33)
q Press [GRP] twice.
w Press [1] [0]. (Press [RET] to cancel.)
e Press [ENTER].
Direct File Selection
Example: File number 10
q Press [GRP].
w Press [1] [0]. (Press [RET] to cancel.)
e Press [ENTER].
Note:
¡To suspend direct selection, press [DISP].
¡ Random, Folder Random, Repeat and Folder Repeat
plays are canceled once [ENTER] is pressed.
Play
Folder : 001/009 File : 0001/0100 Time: 00:00:13
DivX display example
Page: 25
26
25
E
N
G
L
I
S
H
CQ-D1703N
DVD/VCD Player
You can enjoy watching DVDs and VCDs if the optional monitor (CY-VM7203N) is connected.
When a disc is in the player
Press [SRC/PWR] to select the DVD/VCD player mode
and playback starts. (If automatic start is not performed,
press [5] (PLAY) of the remote control, or try to operate it
manually according to the menu screen of the disc.)
(When DVD disc is in the player)
(When VCD disc is in the player)
Display Change
Press [DISP].
3DVD disc 3VCD disc
Chapter Selection
[d]: Next chapter
[s]: Beginning of the current chapter
For the previous chapter, press twice.
Fast Forward/Fast Reverse
Press and hold for more than 0.5 seconds.
Each time you press the button, the speed changes as follows.
Regular speed /2 times /5 times /10 times /20 times
[d] (f): Fast forward
[s] (a): Fast reverse
Press [BAND] (y / 5) to cancel.
Pause (y / 5)
Press [BAND] (y / 5).
Press [BAND] (y / 5) again to cancel.
Slow play
Press and hold [d] for more than 0.5 seconds during
pausing.
Press [BAND] (y / 5) again to cancel.
Repeat Play
The current chapter is repeated.
Press and hold [6] (REPEAT) for more than 2 seconds.
light.
Press and hold [6] (REPEAT) again for more than 2 sec-
onds to cancel.
VCD
Clock time
Title/Chapter
Clock time
Title Chapter
[DISP] (Display)
[SRC/PWR] (Source)
[6] (REPEAT)
[s] / [d] (a / f)
(Chapter selection/fast
forward/fast reverse/
slow play)
[}]/[{]/[]]/[[]
[BAND]
(y / 5: Pause/play)
[ENTER]
Play
Title:02/03 Chapter:025/050 Time: 02:35:40
DVD display example
Page: 26
27
26
E
N
G
L
I
S
H
CQ-D1703N
Functions Only by Remote Control Unit
Stop
Press [3] (STOP).
Press [5] (PLAY) to resume playback from the point
where [3] (STOP) is pressed. (Continued playback func-
tion)
To cancel continued playback, press [3] (STOP) again in
the stop mode.
Frame to Frame Play
Press [y] (PAUSE) to go to next frame in the pause.
To resume normal playback, press [5] (PLAY).
Direct Selection (during play-
back)
Direct Chapter Selection
Example: Chapter number 10
q Press [GRP].
w Press [1] [0]. (Press [RET] to cancel.)
e Press [ENTER].
Direct Title Selection
Example: Title number 10
q Press [GRP] twice.
w Press [1] [0]. (Press [RET] to cancel.)
e Press [ENTER].
List Selection
Only for PBC-applicable (Playback control a Page 45)
VCDs or some DVDs
Example: List number 10
q Press [1] [0]. (Press [RET] to cancel.)
w Press [ENTER].
Note:
¡If a non-existent title/chapter/track/number is input and
entered, the command is invalid and the display returns
to regular mode.
¡Direct title selections can be made by pressing [GRP]
once in the stop mode.
¡To return to the regular mode, press [DISP].
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
VCD
VCD
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
VCD
VCD
DVD
DVD
DVD VCD
VCD
VCD
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[0] – [9]
[RET]
[GRP]
[y] (PAUSE)
[5] (PLAY)
[3] (STOP)
Disc Menu
You can stop playing the disc temporarily and call up the
on-disc menu screen.
q Press [MENU] on the remote control during playback.
w Press [}]/[{]/[]]/[[] to select an item.
e Press [ENTER] to determine the selection.
Title Menu
You can stop playing the disc temporarily and call up the
on-disc title menu screen.
q Press and hold [MENU] (TITLE) on the remote con-
trol for more than 2 seconds during playback.
w Press [}]/[{]/[]]/[[] to select an item.
e Press [ENTER] to determine the selection.
Note:
¡You can also select an item by pressing [0] to [9] on the
remote control. (Press [RET] to cancel the operation.)
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
[}]/[{]/
[]]/[[]
[ENTER]
[MENU]
(TITLE)
Page: 27
28
27
E
N
G
L
I
S
H
CQ-D1703N
Advanced Operation for Video Discs (DVD/VCD/DivX)
Display the unit’s registration
code
(Only for remote control unit, a Page 42 “User Settings”)
q Press [MENU]
w Press [9].
8 alphanumeric characters
Note:
¡We recommend that you make a note of this code for
future reference.
¡After playing DivX VOD content for the first time, anoth-
er registration code is then displayed in “DivX
Registration”. Do not use this registration code to pur-
chase DivX VOD content. If you use this code to pur-
chase DivX VOD content, and then play the content on
this unit, you will no longer be able to play any content
that you purchased using the previous code.
¡If you purchase DivX VOD content using a registration
code different from this unit’s code, you will not be able
to play this content. (“Authorization Error” is displayed.)
Regarding DivX content that
can only be played a set num-
ber of times
Some DivX VOD content can only be played a set number
of times. When you play this content, the remaining num-
ber of plays is displayed. You cannot play this content
when the number of remaining plays is zero.
(“Rental Expired” is displayed.)
When playing this content
¡The number of remaining plays is reduced by one if
- you press [SRC/PWR].
- you press [3] (STOP) on the remote control unit.
- you press [s] / [d] (a / f)
etc. and arrive at another content or the start of the
content being played.
¡Resume (a Page 27 “Stop”) function does not work.
DivX(R) Video On Demand
Your registration code is :XXXXXXXX
To learn more visit www.divx.com/vod
<Registration Code>
RETURN : Setup Menu
About DivX VOD content
DivX Video-on-Demand (VOD) content is encrypted for copyright protection. In order to play DivX VOD content on this unit,
you first need to register the unit.
Follow the on line instructions for purchasing DivX VOD content to enter the unit’s registration code and register the unit.
For more information about DivX VOD, visit www.divx.com/vod.
[SRC/PWR] (Source/power)
[s] / [d] (a / f)
(File selection/fast for-
ward/fast reverse)
Page: 28
29
28
E
N
G
L
I
S
H
CQ-D1703N
Functions Only by Remote Control Unit
Most compressed mode: TV
broadcasts, etc
Mode recommended by software
creators for listening at low
volumes.
Does not compress the dynamic
range. (Default)
MINIMUM
OFF
STANDARD
Conversation level
MINIMUM STANDARD OFF
Caution
¡ The sound of DVD video covers a wide dynamic range
of more than 100 dB. Thus, the reproduced sound
volume of some DVD discs may be significantly low.
When you increase the volume in this case, the sound
may reach the peak level suddenly and it may lead to
a traffic accident. To avoid such an accident, you can
use this function.
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[0] (DRC)
Subtitle
You can select a subtitle language if the loaded disc has
multi-language subtitles.
When [1] (SUBTITLE) is kept pressed for more than 1
second, the subtitle language is changed over at the inter-
vals of 1 second.
Audio
You can select an audio channel if the disc holding multi-
audio channels is loaded.
When [2] (AUDIO) is kept pressed for more than 1 sec-
ond, the audio channel is changed over at the intervals of 1
second.
Note:
¡Channel change may take time when a DivX file plays
depending on its file structure.
Audio
You can select audio output among “STEREO”, “MONO L”
and “MONO R”.
When [2] (AUDIO) is kept pressed for more than 1 sec-
ond, the audio output is changed over at the intervals of 1
second.
Angle
You can select an angle if a multi-angle disc is loaded.
When [3] (ANGLE) is kept pressed for more than 1 sec-
ond, the angle is changed over at the intervals of 1 second.
D.Range Compression
You can select a range of dynamic range compression.
This function is effective for playback of Dolby
Digital/Dolby Surround DVD video. The words of an actor
hardly audible during playback at a low volume, for exam-
ple, will become easier to listen to by selecting “MINI-
MUM”.
q Press and hold [0] (DRC) during playback for more
than 2 seconds to activate the DRC selection mode.
w Press and hold [0] (DRC) for more than 2 seconds to
select a range of DRC.
DVD
DVD
DVD VCD
DVD
DVD
DVD VCD
STEREO MONO L MONO R
DVD VCD
VCD
VCD
DVD VCD CD MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
DVD VCD CD MP3 DivX
DivX
DivX
DVD
DVD
DVD VCD
[1] (SUBTITLE)
[2] (AUDIO)
[3] (ANGLE)
[3] (STOP)
[MENU]
[9]
Page: 29
30
29
E
N
G
L
I
S
H
CQ-D1703N
OSD (On-Screen Display)
You can see OSDs (On-Screen Display) if the optional monitor (CY-VM7203N) is connected.
OSD (On-Screen Display)
(Only for remote control unit)
You can set up the optional monitor to display or hide the following information: title/artist name for CDs, album/title/artist
name for MP3, playtime for VCDs/DivX and title/chapter/playtime for DVDs.
Each time you press [OSD], the display changes according to the disc type.
Play
CD PLAYER MODE
Track: 12/22 Time: 00:00:13
Play
Title : BEST OF MUSIC
Track 12: FAVORITE
Artist : GREAT SINGER
Track: 12/22 Time: 01:00:13
Play
Title : BEST OF MUSIC
Track 12: FAVORITE
Artist : GREAT SINGER
Track: 12/22 Time: 00:03:13
Total play time
Track play time
3CD (Music CD)
CD player mode
Play
MP3 PLAYER MODE
Folder : 001/009 File : 0001/0100 Time: 00:00:13
Play
Folder :MP3 MUSIC
File :WINTER.mp3
ID3Tag
Album :BEST OF MUSIC
Title :FAVORITE
Artist :GREAT SINGER
Folder : 001/009 File : 0001/0100 Time: 00:00:13
MP3 player mode
ID3 TAG ON
3MP3
Play
Folder : 001/009 File : 0001/0100 Time: 00:00:13
DivX player mode
Text off
3DivX
Page: 30
31
1
E
N
G
L
I
S
H
CQ-D1703N
30
Play
Title:02/03 Chapter:025/050 Time: 02:35:40
Play
Title:02/03 Chapter:025/050 Time: 00:05:59
Chapter play time
Text off
3DVD (DVD Video)
Total play time
Play time
Text off
3VCD (Video CD)
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[OSD]
Page: 31
32
31
E
N
G
L
I
S
H
CQ-D1703N
Notes on MP3/DivX
What is MP3/DivX?
MP3: MP3 (MPEG Audio Layer-3) is the compression format of
digital audio. It is developed by MPEG (Motion Picture Experts
Group). Using this compression format, you can record the con-
tents of about 10 music CDs on a single CD (This figure refers to
data recorded on a 650 MB CD-R or CD-RW at a fixed bit rate of
128 kbps and a sampling frequency of 44.1 kHz).
DivX: The video compression format developed by DivX, Inc.
compresses video files without any considerable loss of video
quality.
Note:
¡MP3/DivX encoding and CD writing software programs are not
supplied with this unit.
Points to remember when making MP3/DivX files
Common
¡High bit rate and high sampling frequency are recommended
for high quality sound.
¡Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound may
be skipped.
¡The playback sound quality differs depending on the encoding
circumstances. For details, refer to the instructions of your
own encoding software and writing software.
MP3
¡ It is recommended to set the bit rate to “128 kbps or more”
and “fixed”.
DivX
¡DivX files greater than 2GB or having no index may not play
properly on this unit.
¡This unit supports all resolutions up to maximum of 720 x 480
(NTSC)/720 x 576 (PAL).
¡You can select up to 8 types of audios and subtitles on this
unit.
¡ GMC (Global Motion Compensation) is not supported.
Display Information (on the Main Unit)
Displayed items
Displayable characters
¡Displayable length of file name/folder name: within 64 charac-
ters. (Unicoded file and folder names are reduced by half in
the number of displayable characters.)
¡Name files and folders in accordance with the standard of each file
system. Refer to the instructions of writing software for details.
¡ASCII character set can be displayed.
¡ Some Cyrillic characters in the Unicode can be displayed.
ASCII character set
A to Z, a to z, digits 0 to 9, and the following symbols:
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ~
Note:
¡With some software in which MP3/DivX format files have been
encoded, the character information may not be displayed properly.
¡Undisplayable characters and symbols will be converted into
an asterisk ( ).
¡It is recommended that the length of the file name is less than
8 (excluding the file extension).
¡ CD-TEXT
Disc title
Track title
¡ MP3/DivX
Folder name
File name
¡ MP3 (ID3 tag)
Album name
Title and artist name
Caution
¡ Never put “.mp3” to other than MP3-formatted
data or “.DIVX”, “.divx”, “.AVI”, and “.avi” to
other than DivX-formatted data. This may not
only produce noise from the speaker damage,
but also damage your hearing.
Page: 32
33
1
E
N
G
L
I
S
H
CQ-D1703N
32
Root Folder
(Root Directory)
Folder Selection
File Selection
Tree 1 Tree 2 Tree 3 Tree 4 Tree 8
(Max.)
2
1
3
4
q
q
w
e
r
t
y
y
5
6
8
1 8
7
–
In the order
–
In the order
¡ It is recommended not to use a disc holding two or more
different format types of files.
¡ If CD-DA files are on the same disc as MP3 or DivX files,
the songs and the movies may not play in the intended
order, or some songs or movies may not play at all.
¡ When storing MP3 data and DivX data on the same disc,
use different folders for each data.
¡ Do not record files other than MP3/DivX files and unneces-
sary folder on a disc.
¡ The name of an MP3/DivX file should be added by rules as
shown in the following descriptions and also comply with the
rules of each file system.
¡ The file extension “.mp3” should be assigned to MP3 files.
¡ The file extension “.DIVX”, “.divx”, “.AVI” or “.avi” should be
assigned to DivX files.
¡ You may encounter trouble in playing MP3/DivX files or dis-
playing the information of MP3/DivX files recorded with cer-
tain writing software or CD/DVD recorders.
¡ This unit does not have a play list function.
¡ Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Romeo
Note:
¡ Apple HFS, UDF 1.50, Mix CD and CD Extra are not supported.
Recording MP3/WMA files on a CD-media
Folder selection order/file playback order
Maximum number of files/folders
¡Maximum number of files: 1200
¡ Maximum number of files in one folder: 1200
¡ Maximum depth of trees: 8
¡ Maximum number of folders: 255 (Root folder is included.)
Note:
¡You can shorten the duration between data read and playback by
decreasing the quantity of files or folders, or the depth of the hier-
archy.
¡ This unit counts the number of folders irrespective of the presence or
absence of an MP3/DivX file.
¡ If the selected folder does not contain any MP3/DivX files, the nearest
MP3/DivX files in the order of playback will be played.
¡ Playback order may be different from other MP3/DivX players even if
the same disc is used.
¡ “ROOT” appears when displaying the root folder name. Copyright
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself
personally.
No warranty
The above description complies with our investigations
as of May 2006. It has no warranty for reproducibility
and displayability of MP3/DivX.
Recording MP3/DivX files on a CD/DVD-media
8 k – 48 kHz
Yes
8 k – 320 kbps
DivX data created using ver.3.11, 4.x, 5.x*
16, 22.05, 24 kHz
Yes
8 k – 160 kbps
MPEG 2 audio layer 3 (MP3)
32, 44.1, 48 kHz
Yes
32 k – 320 kbps
MPEG 1 audio layer 3 (MP3)
Sampling frequency
VBR
Bit rate
Compression method
Audio compression formats (Recommendation: “Points to remember when making MP3/DivX files” on the previous page)
* DivX video system/MP2, MP3 Note:
¡ VBR is not recommended.
Page: 33
34
33
E
N
G
L
I
S
H
CQ-D1703N
Audio Settings
Bass/Treble
You can adjust the bass and treble sounds.
Default: BAS (bass) 0 dB
TRE (treble) 0 dB
Setting range: –12 dB to +12 dB (by 2 dB)
Press [VOLUME] (PUSH SEL).
Press [VOLUME] (PUSH SEL).
Volume
Default: 18
Setting range: 0 to 40
Press [VOLUME] (PUSH SEL)
to open the menu.
Press [VOLUME]
(PUSH SEL: select).
(Press [SEL] on the
remote control unit.)
Balance/Fader
You can adjust the sound level among the right, left, front and
rear speakers.
Default: BAL (balance) CNT (centre)
FAD (fader) CNT (centre)
Setting range: 15 levels each and CNT (centre)
Press [VOLUME] (PUSH SEL).
Press [VOLUME] (PUSH SEL).
[DISP] (Return to the regular mode)
Turn [VOLUME]. (Press [VOL }] or
[VOL {] on the remote control unit.)
Audio Output Level (for P-MODE)
The audio output level to the rear monitor is adjustable when P-
MODE is set to ON. (a Page 38).
Default: MIN
Setting range: MIN (minimum), MID (middle) and MAX (maxi-
mum)
Press [VOLUME] (PUSH SEL).
(LV: LEVEL)
Regular mode
Page: 34
35
1
E
N
G
L
I
S
H
CQ-D1703N
34
q
w
q
w
q
w
Turn [VOLUME].
q : Up
w : Down
Turn [VOLUME].
q : Up
w : Down
Turn [VOLUME].
q : Up
w : Down
Note:
¡ To return to the regular mode, press [DISP].
¡ If no operation takes place for more than 5 seconds in audio setting (2 seconds in the volume adjustment), the display
returns to the regular mode.
¡ The volume can also be adjusted directly using [VOLUME] on the main unit. (a Page 10)
¡ Balance/Fader is not selectable when P-MODE (private mode a Page 38) is set to ON. (“CAN’T SEL” appears.)
VOLUME BASS
REAR LV FADER
Regular mode TREBLE
BALANCE
q
w
q
w
Turn [VOLUME].
q : Front enhanced
w : Rear enhanced
Turn [VOLUME].
q : Right enhanced
w : Left enhanced
q
w
Turn [VOLUME].
q : Up
w : Down
Note:
¡ Adjust the audio volume of the rear
monitor if necessary.
q
w
Page: 35
36
35
E
N
G
L
I
S
H
CQ-D1703N
Function Settings
Press and hold [VOLUME]
(PUSH SEL) for more than 2
seconds to open the menu.
FM Monaural Reception
(FM mode)
Noise is significantly decreased when weak signals are received
from an FM broadcast station.
Default: OFF
Region (REG) Mode (FM mode)
Changes the selection range of AF, Best Station Research and PI
seek.
Default: OFF
Note:
¡ When REG mode is switched from OFF to ON or vice versa,
AF mode turns on automatically.
Press [VOLUME] (PUSH SEL).
Local Tuning (Radio mode)
Only stations with good reception are detected in seek tuning.
Default: OFF
Press [VOLUME] (PUSH SEL).
Press and hold
[VOLUME] (PUSH
SEL: select) for more
than 2 seconds.
PTY Language Selection (RDS
mode)
Default: ENGLISH
Press [VOLUME] (PUSH SEL).
(Page 38)
[DISP] (Return to the regular mode)
Turn [VOLUME]. (Press [}] or [{] on
the remote control unit.)
Page: 36
37
1
E
N
G
L
I
S
H
CQ-D1703N
36
Turn [VOLUME].
: MONO ON
: MONO OFF (Default)
w
q
indicator
Turn [VOLUME].
: The frequency is changed only for programmes within the
region.
: The frequency is changed also for programmes outside the
region. (Default)
w
q
Turn [VOLUME].
: LOCAL ON
: LOCAL OFF (Default)
w
q
indicator
Note:
¡ To return to the regular mode, press [DISP].
¡ If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode.
q
w
q
w
q
w
FM MONO
ACC SET EXT MUTE
Regular mode
PTY LANG
P-MODE
(FM Mode)
(RDS Mode)
FM LOCAL AM LOCAL
(FM Mode) (AM Mode)
REGION (FM Mode)
Turn [VOLUME].
: English (Default)
: Swedish
q
w
q
w
Page: 37
38
37
E
N
G
L
I
S
H
CQ-D1703N
Private Mode (P-MODE)
Private Mode can be toggled.
Default: OFF
P-MODE ON: Provides rear seat passengers with images and
sounds of Discs. This setting selects Disc Player
(CD/MP3/DVD/VCD/DivX) as a source for the rear monitor and
decreases the audio output from the rear speakers to zero. Use
of rear monitor’s headphones with this setting can relax rear
seat passengers.
P-MODE OFF: Provides passengers in both the front and rear
seats with the same source.
Press [VOLUME] (PUSH SEL).
External Mute
Allows you to mute the current source while Panasonic naviga-
tion system provides voice guidance or car telephone conversa-
tion is in progress.
Default: 0
Setting range: 0 to 2, OFF
Press [VOLUME] (PUSH SEL).
Function Settings (continued)
Press [VOLUME]
(PUSH SEL: select).
ACC Selection
Default: OFF
Caution
¡ Be sure to select OFF when your car has no ACC position in
the ignition switch. Failure to do this could cause the battery
to go dead.
Press [VOLUME] (PUSH SEL).
[DISP] (Return to the regular mode)
Turn [VOLUME]. (Press [}] or [{] on
the remote control unit.)
(Page 36)
Page: 38
39
38
E
N
G
L
I
S
H
CQ-D1703N
q
w
Turn [VOLUME].
: No sound (Default)
: 15 steps decrease
: 10 steps decrease
: Unchanged
When External Mute is activated.
(Example: MUTE LV 0)
Note:
¡ To return to the regular mode, press [DISP].
¡ If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode.
Turn [VOLUME].
: P-MODE ON
: P-MODE OFF
q
w
q
w
q
w
FM MONO
ACC SET EXT MUTE
Regular mode
PTY LANG
P-MODE
(FM Mode)
(RDS Mode)
FM LOCAL AM LOCAL
(FM Mode) (AM Mode)
REGION (FM Mode)
¡The power is turned on when a disc is inserted while the
power is off.
¡The Clock Time can be displayed while power is off.
Turn [VOLUME].
Set to ON if your car
has ACC position.
Set to OFF if your car
has no ACC position.
(Default)
q
w
q
w
ACC ON
Note:
¡ Be sure to select P-MODE OFF when P-MODE is not used.
¡ P-MODE ON cannot be selected (“CAN’T SEL” displayed) when no disc is loaded in this unit.
¡ Ejection of the disc activates P-MODE OFF.
(P-MODE) indicator
Page: 39
40
39
E
N
G
L
I
S
H
CQ-D1703N
User Settings
The following information explains the settings only about the disc player and displayed contents on the screen.
(Only for Remote Control Unit)
1. Menu Language
Disc menu language selection
Default: English
4. OSD Language
Default: English
3. Audio Language
Default: English
2. Subtitle Language
Default: English
q Display “Setup Menu”.
Press [MENU]. w Select each setting menu.
Press one of the numeric buttons from [1] to [9].
(Example: “1. Menu Language”)
1. Menu Language : English
2. Subtitle Language : English
3. Audio Language : English
4. OSD Language : English
5. TV Type : PAL
6. TV Display : WIDE
7. On-Screen Messages : ON
8. D. Range Compression : OFF
9. DivX Registration
<Setup Menu>
0. Exit
1. Menu Language : English
2. Subtitle Language : English
3. Audio Language : English
4. OSD Language : English
5. TV Type : PAL
6. TV Display : WIDE
7. On-Screen Messages : ON
8. D. Range Compression : OFF
9. DivX Registration
<Setup Menu>
0. Exit
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[MENU]
Numeric buttons
[1] – [9]
[0]
(Finish the
setting.)
Note:
¡Setup Menu has been arranged not for any DVD
disc but for this unit.
¡Setup Menu is operable only if the disc source
has been selected. (No disc playing)
Page: 40
41
40
E
N
G
L
I
S
H
CQ-D1703N
1. English
2. French
3. Spanish
4. Chinese
5. German
6. Italian
7. Other (a Page 44)
8. Return The display returns to “Setup Menu”.
1. English
2. French
3. Spanish
4. Chinese
5. German
6. Italian
7. Other (a Page 44)
8. Disp Off Subtitle language is not displayed.
9. Return The display returns to “Setup Menu”.
Note:
¡ A disc supporting closed captioning and subtitles
may overlap on the screen. In this case, turn the
subtitle off.
1. English
2. Chinese
3. Return The display returns to “Setup Menu”.
1. English
2. French
3. Spanish
4. Chinese
5. German
6. Italian
7. Other (a Page 44)
8. Return The display returns to “Setup Menu”.
e Select each item.
Press one of the numeric buttons from [1] to [9].
(Example: “1. English”)
r Finish the setting.
Press [0] (Exit). (The setting is completed.)
Note:
¡To apply changes to the setting, be sure to
press [0] (Exit) at the end.
¡After the user settings have been changed and
entered, the player returns to the start of the
disc.
¡When the disc has predetermined language or
other settings, the user settings are not
reflected.
Select 1. English
Language 2. French
3. Spanish
4. Chinese
5. German
6. Italian
7. Other
8. Return
<Menu Language>
Page: 41
42
41
E
N
G
L
I
S
H
CQ-D1703N
5. TV Type
TV standard format (PAL/NTSC) setting
Default: PAL
Note:
¡Setting should be made to match the format of the
connected monitor. Select NTSC if connections are
made possible for both NTSC and PAL. If you select
PAL, a picture may be partly omitted.
¡This unit is not compatible with SECAM format.
8. D.Range Compression
By compressing the range of the playback level (the
dynamic range), it is possible to maintain the impact
of audio even at low volumes.
This function only works with Dolby Digital encoded
material.
Default: OFF
7. On-Screen Messages
This is to select On-screen Display messages which
will be displayed when On-screen Display is turned
off by pressing [OSD] (a Page 30).
Default: ON
6. TV Display
Display aspect setting
Default: WIDE
9. DivX Registration
(a Page 28)
q Display “Setup Menu”.
Press [MENU]. w Select each setting menu.
Press one of the numeric buttons from [1] to [9].
(Example: “6. TV Display”)
1. Menu Language : English
2. Subtitle Language : English
3. Audio Language : English
4. OSD Language : English
5. TV Type : PAL
6. TV Display : WIDE
7. On-Screen Messages : ON
8. D. Range Compression : OFF
9. DivX Registration
<Setup Menu>
0. Exit
1. Menu Language : English
2. Subtitle Language : English
3. Audio Language : English
4. OSD Language : English
5. TV Type : PAL
6. TV Display : WIDE
7. On-Screen Messages : ON
8. D. Range Compression : OFF
9. DivX Registration
<Setup Menu>
0. Exit
User Settings (continued)
The following information explains the settings only about the disc player and displayed contents on the screen.
(Only for Remote Control Unit)
Note:
¡Setup Menu has been arranged not for any DVD
disc but for this unit.
¡Setup Menu is operable only if the disc source
has been selected. (No disc playing)
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[MENU]
Numeric buttons
[1] – [9]
[0]
(Finish the
setting.)
[RET] (RETURN)
Page: 42
43
42
E
N
G
L
I
S
H
CQ-D1703N
1. NTSC The unit transmits the NTSC formatted signal in either case, playing an NTSC formatted video or a
PAL formatted video.
2. PAL The unit transmits the PAL formatted signal in either case, playing an NTSC formatted video or a
PAL formatted video.
3. Multi The unit transmits the same video signal as the output of playing video software.
Note:
¡If the connected monitor cannot automatically select between NTSC and PAL according to the
video signal of the disc to be reproduced, images on the screen may be distorted. Select NTSC
or PAL at the monitor side depending to the disc to be reproduced.
4. Return The display returns to “Setup Menu”.
1. WIDE (16:9) Plays in Wide mode when a wide-screen monitor is connected.
2. Pan & Scan (4:3) Plays in Pan & Scan mode when a conventional monitor is connected.
3. Letterbox (4:3) Plays in Letterbox mode when a conventional monitor is connected.
4. Return The display returns to “Setup Menu”.
Note:
¡If “Pan & Scan” or “Letterbox” is already set in the software, this setting is ignored.
1. Minimum Most compressed mode: TV
broadcasts ,etc
2. Standard Mode recommended by software
creators for listening at low volumes.
3. OFF Does not compress the dynamic
range.
4. Return The display returns to “Setup Menu”.
Note:
¡ When it is difficult to hear comparatively small
sound (such as movie dialogue), setting “Minimum”
will make those sounds easier to hear.
1. ON When power is turned on, On-Screen Display message such as “Play” and “Pause”
will be displayed on the screen for 5 seconds.
2. OFF When power is turned on, On-Screen Display messages such as “Play” and
“Pause” will not be displayed on the screen.
3. Return The display returns to “Setup Menu”.
To return to the “Setup Menu” display, press [RET] (RETURN).
e Select each item.
Press one of the numeric buttons from [1] to [4].
(Example: “2. Pan & Scan (4:3)”)
r Finish the setting.
Press [0] (Exit). (The setting is completed.)
Note:
¡To apply changes to the setting, be sure to
press [0] (Exit) at the end.
¡After the user settings have been changed and
entered, the player returns to the start of the
disc.
¡When the disc has predetermined language or
other settings, the user settings are not
reflected.
<TV Display Mode>
Select TV 1. WIDE (16:9)
Display Mode 2. Pan & Scan (4:3)
3. Letterbox (4:3)
4. Return
Page: 43
44
43
E
N
G
L
I
S
H
CQ-D1703N
Language Code List
(Only for Remote Control Unit)
In “Other” cases (Menu Language, Subtitle Language, Audio Language) (a Page 40)
8277 Rhaeto-Romance
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8372 Serbo-Croatian
8373 Singhalese
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
Code Language Name
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7665 Latin
7678 Lingala
7679 Laothian
7684 Lithuanian
7686 Latvian, Lettish
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Punjabi
8076 Polish
8083 Pashto, Pushto
8084 Portuguese
8185 Quechua
Code Language Name
6565 Afar
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6589 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
6678 Bengali; Bangla
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7273 Hindi
7282 Croatian
7285 Hungarian
Code Language Name
q Press numeric buttons from
[0] to [9] to input the 4 digit
language code. (See below.)
¡ To input the number again,
press [RET] (RETURN).
w Press [ENTER] to finalize the
selection.
¡ Setting is finished and the
display returns to “Setup
Menu”.
CAR AV
1 3
2
4 6
5
7 9
8
0 MUTE
EN
T
E
R
PAUSE PLAY
STOP
SRC
RET
POWER
SOURCE
TRACK
RANDOM
RETURN TITLE
TRACK / SEARCH
MENU
AUDIO ANGLE
GRP
SCAN
DRC
SUBTITLE
REPEAT
TITLE/CHAPTER
SEL
OSD
VOL
[ENTER]
[0] – [9]
[RET]
Page: 44
45
44
E
N
G
L
I
S
H
CQ-D1703N
Definition of Terms
Digital audio output connector (Optical)
The digital audio output connector (optical) converts
electrical signals into optical signals and transfers
them to the amplifier. Consequently, it has a number
of features including its immunity from electrical inter-
ference from external sources and its ability to prevent
the generation of noise and its minimal effect on the
external environment.
Dolby Digital
This fully discrete format divides the music signals
into 5.1 channels: Front Left (L), Front Right (R),
Centre (C), Left Surround (LS), Right Surround (RS)
and Subwoofer (SW: 0.1 channel) for recording and
playback. The number of channels that are recorded
depends on the software. (1 to 5.1 channels)
Interactive DVD
An interactive DVD is DVD software which includes
multiple angles, multiple plot endings, etc.
Letterbox screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s appears
with black bands running along the top and bottom.
LPCM (Linear PCM audio)
In this format, the audio signal is converted to digital
data and recorded in two channels without compres-
sion. Because the capacity of a DVD disc is large, it
can store more data with better accuracy than a CD.
Pan & Scan screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s is cut off at
the left and right sides.
Playback control (VCD (Video CD))
If the VCD (Video CD) has “With Playback Control” or
others written on the disc surface or on the jacket, the
scenes or information to be viewed (or listened to) can
be selected interactively with the screen by looking at
the menu shown on the screen.
In these instructions, playback using the menu screen
is referred to as the “menu play” for video CDs. This
player supports Video CDs with playback control.
dts
This format requires more data than Dolby Digital, and
provides higher quality surround playback.
Similar to Dolby Digital, this fully discrete format
divides the music signals into 5.1 channels: Front Left
(L), Front Right (R), Center (C), Left Surround (LS),
Right Surround (RS) and Subwoofer (SW: 0.1 chan-
nel) for recording and playback.
DivX
DivX is a popular media technology created by DivX,
Inc. DivX media files contain highly compressed video
with high visual quality that maintains a relatively
small file size. DivX files can also include advanced
media features like menus, subtitles, and alternate
audio tracks. Many DivX media files are available for
download online, and you can create your own using
your personal content and easy-to-use tools from
DivX.com.
Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are trademarks
of Dolby Laboratories.
Confidential unpublished works. Copyright
1992–1997 Dolby Laboratories. All rights
reserved.
“DTS” and “DTS Digital Out” are trademarks of Digital
Theater Systems, Inc.
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be authorized
by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Official DivX®
Certified product
Plays all versions of DivX®
video (including DivX®
6)
with standard playback of DivX®
media files
DivX,DivX Certified, and associated logos are trade-
marks of DivX, Inc. and are used under license.
Page: 45
46
45
E
N
G
L
I
S
H
CQ-D1703N
Caution
¡ This face plate is not waterproof. Do not expose it to water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby areas where the temperature rises high.
¡ Do not touch the contacts on the face plate and on the main unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.
Anti-Theft System
1
2
This unit is equipped with a removable face plate. Removing
this face plate makes the unit totally inoperable.
Remove the Face Plate
q Switch off the power of the unit.
w Press [ ] (Release) to remove the face plate. (The face
plate disengages with a click when it is removed.)
e Place the face plate into the case and take it with you when
you leave the car.
Note:
¡Be absolutely sure to turn off the power of the unit before
removing the face plate.
¡Do not install or remove the face plate while it is moving.
Install the Face Plate
q Slide the left side of the face plate in place.
w Press the right end of the face plate until a “click” is heard.
Removable
Face Plate
Case
Contact
[ ] (Release)
Page: 46
47
1
E
N
G
L
I
S
H
CQ-D1703N
46
How to hold a disc
¡ Do not touch the underside of a disc.
¡ Do not scratch a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ In direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ On seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the centre outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint pen or other
hard-point pens.
Notes on Discs
Notes on CD-Rs/RWs, DVD-Rs/RWs
¡ You may have trouble playing back some CD-R/RW, DVD-R/RW discs recorded using CD/DVD recorders (CD-R/RW,
DVD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
¡ CD-R/RW, DVD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs/DVDs.
Leaving them inside a car for extended periods may damage and make playback impossible.
¡ Some CD-Rs/RWs, DVD-Rs/RWs cannot be played back successfully due to incompatibility among writing software, a
CD/DVD recorder (CD-R/RW, DVD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW, DVD-R/RW discs if the session is not closed.
¡ Be sure to observe the instructions of the CD-R/RW, DVD-R/RW disc for handling it.
¡ This player cannot play the CD-R/RW discs which contain other than CD-DA or MP3/DivX data.
¡ This player cannot play DVD-Rs/RWs which contain other than DVD Video/MP3/DivX data.
Fuse
If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Service Centre.
Warning
¡Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest
authorized Panasonic Service Centre.
Maintenance
This unit is designed and manufactured to ensure the minimum of maintenance. Use a dry, soft cloth for routine exterior
cleaning. Never use benzine, thinner, or other solvents.
Printed side
<Correct> <Wrong>
Irregularly shaped discs
Labels created by a printer
Page: 47
48
47
E
N
G
L
I
S
H
CQ-D1703N
Installation
e
2
3
4
5
6
4 w
4
4
w
q
1 Remove the cable from the battery
negative terminal.
2 Mounting collar q insertion.
Bend appropriate tabs to secure the
unit without backlash.
3 Connection of power connector t.
4 Main unit securing
q Screw the Mounting bolt w into the main unit.
w Secure to the fire wall.
e Snap the right and left springs into each hole.
5 Trim plate r mounting
6 Battery Cable reconnection
Using the rubber bushing
(Option)
Using the rear support strap
(Option)
Clank!
Snapping Point
Securing to fire wall
Tapping screw (Option)
3 mm ø
Rear support
bracket
(supplied with car)
Mounting Bolt w
Mounting Bolt w
Rear support
strap (Option)
To the unit
Caution
¡ Wear gloves for safety
¡ Make sure that wiring is completed
before installation.
¡ When this unit is installed in dashboard,
ensure that there is sufficient air flow around the unit to
prevent damage from overheating, do not block any
ventilation holes on the unit.
How to install the unit
Remove Mounting Collar q and Trim Plate r from the
main unit temporarily, which are already mounted at ship-
ment.
Warning
❐ This installation information is designed for professional installers with knowledge of automobile electrical safety sys-
tems and is not intended for non-technical, do-it-yourself individuals. It does not contain instructions on the electrical
installation and avoidance of potential harm to air bag, anti-theft and ABS braking or other systems necessary to install
this product. Any attempt to install this product in a motor vehicle by anyone other than a professional installer could
cause damage to the electrical safety system and could result in serious personal injury or death.
❐ If your car is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and
disconnection of the battery to install this product. Before attempting installation of this electronic component against
the manufacturer’s recommendation, you must contact your car dealer or manufacturer to determine the required proce-
dure and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVA-
TION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.
Hexagonal nut
(Option)
Rubber Bushing
(Option)
Page: 48
49
48
E
N
G
L
I
S
H
CQ-D1703N
53 mm
182 mm
4.5 mm – 6.0 mm
0 – 30°
Consult a professional for installation.
Verify the radio using the antenna and speakers before installation.
Mounting Angle Mounting Space
side to side : horizontal
front to rear : 0 – 30°
1 Remove the face plate.
2 Remove the trim plate r.
3 Lock release
q Insert the lock cancel plate y until you hear a click.
w Pull the main unit.
4 Pull out the unit with both hands.
w
q
w
q
q
e
w
How to remove the unit
Supplied Hardware
1
1
1
1
2
1
Mounting Collar
Mounting Bolt (5 mmø)
ISO Antenna Adapter
Trim Plate
Power Connector
Lock Cancel Plate
No. Diagram Q'ty
Item No. Diagram Q'ty
Item
1
Clip Connector
* w, e, y and u consist of a set. (YEP0FZ5725)
(YEFC05657)
(YEFX0217263A)
(K1HY12YY0001)
182 mm
53 mm
4.5 mm – 6 mm
Page: 49
50
49
E
N
G
L
I
S
H
CQ-D1703N
Wiring
¡ Exclusively operated with 12 V battery with negative (–) ground.
¡ Connect the power lead (red) very last.
¡ Connect the battery lead (yellow) to the positive (+) terminal of the battery or fuse block terminal (BAT).
¡ Apply insulating tape to bare leads.
¡ Secure loosened leads.
Before Wiring
Connect as follows
¡ Use ungrounded speakers only.
Allowable input: 50 W or more
Impedance: 4 – 8 Ω
¡ Distance between speaker and amplifier: 30 cm or more
¡ Do not use a 3-wire type speaker system having a common
earth lead.
Caution
¡ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Speaker Connection
Page: 50
51
50
E
N
G
L
I
S
H
CQ-D1703N
–
+
PARKING BRAKE
The parking brake switch position varies with the car
model.
For details on the exact location of the parking brake
switch in your car, contact your dealer.
q Attach a Clip Connector u to the end
of the parking brake connection lead.
w The Clip Connector u is connected to
the power source side lead of the park-
ing brake.
Connecting the Parking Brake Connection Lead
Hand brake Foot brake
Parking Brake Lead
(Blue/yellow stripe)
When the parking brake lever is
engaged, the unit is grounded by the
chassis.
Parking brake
switch
Car chassis
Battery
Brake light
Clip Connector u
Parking Brake Lead
(Blue/yellow stripe)
Power source side lead
Caution
¡ For safety, be sure to ask your nearest professional installer to do this connection.
When connecting this unit to the rear monitor:
¡ The parking brake lead and grand lead should be connected to the same terminal.

Question & answers

There are no questions about the Panasonic CQ-D1703N5 yet.

Ask a question about the Panasonic CQ-D1703N5

Have a question about the Panasonic CQ-D1703N5 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Panasonic CQ-D1703N5. Please make sure that you describe your difficulty with the Panasonic CQ-D1703N5 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.