Panasonic CQ-C7405W manual

View a manual of the Panasonic CQ-C7405W below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Panasonic
  • Product: Car Radio
  • Model/name: CQ-C7405W
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 0
Model: CQ-C7405W
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
TEXT
AAC WMA MP3 CD Player/Receiver
AAC WMA MP3 CD-ÔÎÂÂ/ÂÒË‚Â
Page: 1
2 CQ-C7405W
Safety Information
Warning
Observe the following warnings when using
this unit.
❑The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this prod-
uct with other battery systems, especially a 24 V DC battery
system.
❑Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult
your dealer or an authorized Panasonic Service Center.
❑Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑Refer fuse replacement to qualified service person-
nel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
Observe the following warnings when
installing.
❑Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑Never use safety-related components for installa-
tion, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gaso-
line tank, and electric wiring are located. Then open the hole
from outside if possible.
❑Never install the product in a location where it inter-
feres with your field of vision.
❑Never have the power cord branched to supply other
equipment with power.
❑After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑In the case of installation to an airbag equipped car,
confirm warnings and cautions of the vehicle manu-
facturer before installation.
❑Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑Insulate all exposed wires to prevent short circuit-
ing.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or death.
■ Read the operating instructions for the unit and all other com-
ponents of your car audio system carefully before using the
system. They contain instructions about how to use the sys-
tem in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■ This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material dam-
age.
Caution
Page: 2
3
English
CQ-C7405W
Caution
Observe the following cautions when using this
unit.
❑Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
❑This unit is designed for use exclusively in automo-
biles.
❑Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑Do not expose the unit to direct sunlight or exces-
sive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on rainy
days.
Observe the following cautions when
installing.
❑Refer wiring and installation to qualified service
personnel.
Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.
❑Follow the instructions to install and wire the prod-
uct.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws, and
moving parts such as seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.
❑Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those sup-
plied or designated may result in internal damage to the unit.
Faulty installation may lead to an accident, a malfunction or
fire.
❑Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑Installation Angle
The product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑Wear gloves for safety. Make sure that wiring is
completed before installation.
❑To prevent damage to the unit, do not connect the
power connector until the whole wiring is complet-
ed.
❑Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling
the battery for the remote control unit.
●Use only specified battery (CR2025).
●Match the polarity of the battery with the (+) and (–) marks
in the battery case.
●Replace dead battery as soon as possible.
●Remove the battery from the remote control unit when not
using it for an extended period of time.
●Insulate the battery (by placing them in a plastic bag or cov-
ering them with vinyl tape) before disposal or storage.
●Dispose of the battery according to the local regulations.
●Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
In case of battery leakage
●Thoroughly wipe the battery liquid off the battery case and
insert new battery.
●If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.
●If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical atten-
tion. Safety
Information
Page: 3
4 CQ-C7405W
Safety Information (continued)
Caution
THIS PRODUCT IS A CLASS I LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company. We
know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have
built into it, you too will be proud to be a member of our family.
Before Reading These Instructions
The instruction manual consists of 2 books. One is “Operating Instructions” describing the operations of the main unit. The other is
“System Upgrade Guidebook” describing the optional devices such as CD changer.
Page: 4
5
English
CQ-C7405W
Before Reading These Instructions (continued)
Safety
Information,
Before
Reading
These
Instructions
Accessories
SEL
SRC
BAND MUTE
2 3
1
5
8
0
6
4
9
7
#
VOL
DISP
CAR AUDIO
MENU
SEL
POWER
SOURCE
SRC
SET
BAND MUTE
2 3
1
5
8
0
6
4
9
7
#
VOL
RANDOM
NUMBER
TUNE TUNE
SCAN REPEAT
DISP
Remote Control Unit
(including a battery)
(CR2025)
Mounting Collar Trim Plate
Power Connector
(EUR7641010)
Q'ty: 1
(FX0214C384ZB)
Q'ty: 1
(YGAJ021011)
Q'ty: 1
Lock Cancel Plate Mounting Bolt
(5 mmø)
Tapping Screw
(5 mmø x 16 mm)
Notes:
¡ The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
¡ Accessories and their parts numbers are subject to
modification without prior notice due to improve-
ments.
¡ Mounting Collar and Trim Plate are mounted on the
main unit at shipment.
Hex. Nut
(5 mmø)
(YEP0FZ5739)
Q'ty: 1 set
Rear Support Strap
(YFG044C002ZA)
Q'ty: 1
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
Operating
Instructions
(YFM284C664CA)
System Upgrade
Guidebook
(YFM284C665CA)
Installation
Instructions
(YFM294C092CA)
Removable Face
Plate Case
Instruction kit
Q'ty: 1 set
(YFC054C089CA)
Q'ty: 1
(YEFC051013)
Q'ty: 1
Page: 5
6 CQ-C7405W
Features
Compatible with the AAC format
This unit has newly become compatible with AAC-formatted
files in addition to the existing MP3 and WMA files.
Note: Some of AAC files (such as SD-Jukebox type) are not
playable.
Hands-Free Phone System
Connection of the optional Hands-Free Phone System (Hands-
Free Kit featuring Bluetooth®
technology: CY-BT100N) allows
users to talk on a handsfree cellular phone if the phone
supports Bluetooth.
Note: This unit is designed only for receiving calls. It
cannot send calls.
Bluetooth®
The Bluetooth word mark and logo are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Matsushita Electric Industrial Co.,Ltd. is under license.
Other trademarks and trade name are those of their
respective owners.
Expansion Module (hub unit)
Connection of the Expansion Module (hub unit, CY-EM100N)
allows users to connect up to 4 optional devices shown below.
Note: A hub unit is not required to connect only one optional
component.
Wide array of components for system upgrade
Various optional components allow users to obtain availability
of wide range of system upgrade. Upgrading the system
delivers relaxed AV space in a car. For further information, refer
to the separate System Upgrade Guidebook.
¡ DVD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the option-
al Panasonic DVD changer unit (CX-DH801W).
¡ CD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the option-
al Panasonic CD changer unit (CX-DP880).
¡ iPod®
The optional adapter (Direct Cable for iPod: CA-DC300N)
allows you to connect the optional iPod series.
iPod is a trademark of Apple Computer, Inc., registered in
the U.S. and other countries.
Sound Control
SQ (Sound Quality)
You have six preset modes (FLAT, ROCK, POP, VOCAL, JAZZ,
CLUB). You can customize your settings for these and save
them for instant recall.
SQ7
This is 7-band equalizer with 60, 160, 400, 1 k, 3 k, 6 k, and 16
kHz. Each band is adjustable between – 12 dB and 12 dB in
steps of 2 dB.
D·M
You can assign your favorite broadcasting station to the
[D·M] button. As the result of doing that, your favorite
broadcasting station can be received even if the unit is in
the CD mode or other modes. (a page 18)
Customize
Initially stored moving images and still images are editable to
taste. IMAGE STUDIO* allows you to process images from a
digital camera or other devices without difficulty. (a page 30)
* This software is downloadable from Panasonic Web site
(http://panasonic.co.jp/pas/en/software/customize/index.html)
Page: 6
7
CQ-C7405W
Contents
¡Safety Information 2
¡Before Reading These Instructions 4
¡Features 6
¡Controls Layout 8
¡Preparation (Clock adjustment etc.) 10
¡General 12
¡Sound Control 16
¡Radio 18
¡CD Player 20
¡MP3/WMA/AAC Player 22
¡Audio Setting 26
¡Function Setting (Security Function Setting etc.) 27
¡Display Setting 28
¡Customize the Display (Customize Function) 30
¡Troubleshooting 32
¡Error Display Messages 35
¡Notes on Discs 36
¡Maintenance/Fuse 36
¡Specifications 37
English 2
Each
Source
As
Needed
ê
êÛ
ÛÒ
ÒÒ
ÒÍ
ÍË
ËÈ
È 38
74
Common
Page: 7
8 CQ-C7405W
Controls Layout
Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
Disc slot
When
Face
Plate
Opens
BAND (a page 18)
y / 5 Pause/Play
(a page 20, 22)
APM Auto Preset Memory
(a page 19)
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
SOURCE Source
PWR Power
(a page 12, 14)
SQ Sound Quality (a page 17)
MENU (a page 27, 28)
P-SET Preset (a page 19)
DISC (a System Upgrade
Guidebook, page 8, 10)
FOLDER (a page 22)
LIST (a System Upgrade
Guidebook, page 12)
DISP Display
(a page 15)
Release
(a page 12)
u OPEN (eject)
(a page 13)
TILT
(a page 13)
MUTE (a page 13)
SBC-SW Super Bass
Control-Subwoofer
(a page 17)
D·M Direct Memory
(a page 18)
Remote Control
Sensor
VOL
(a page 13)
PUSH SEL Select
(a page 26)
SRS WOW
(a page 16)
TUNE
(a page 18)
TRACK (FILE)
(a page 20, 22)
Main
Unit
Page: 8
9
English
CQ-C7405W
Although most of the functions of this unit are executable
with both the main unit and remote control, the following
functions are excluded.
Operations executable only with main unit
¡ Face panel’s opening, closing, tilting, and removal
actions (a page 13)
¡ Disc ejection (a page 13)
¡ SRS WOW on, off, and adjustment (a page 16)
¡ SQ on, off, and adjustment (a page 17)
¡ Direct memory setting and calling (a page 18)
Operations executable only with remote control
¡Preset station calling with one-touch operation
(a page 19)
¡ Direct access to tracks on CDs (a page 21, 23)
¡ Random and repeat play with one-touch operation
(a page 21, 23)
¡ Scan playback (a page 21, 23)
Controls
Layout
Remote
Control
Unit
Operations
executable
only
with
main
unit/
operations
executable
only
with
remote
control
SEL
SRC
BAND MUTE
2 3
1
5
8
0
6
4
9
7
#
VOL
DISP
CAR AUDIO
MENU
SEL
POWER
SOURCE
SRC
SET
BAND MUTE
2 3
1
5
8
0
6
4
9
7
#
VOL
RANDOM
NUMBER
TUNE TUNE
SCAN REPEAT
DISP
POWER
SRC (SOURCE)
MUTE
SBC-SW Super Bass
Control-Subwoofer
BAND
Pause/Play
SET
APM Auto Preset
Memory
SEL Select
MENU
VOL Volume
}:Up
{:Down
DISP Display
0
4
RANDOM
5
SCAN
6
REPEAT
7
9
#
NUMBER
Number Buttons
–
Number
RANDOM
0 to 9
SCAN
REPEAT
9
TUNE
TRACK (FILE)
P·SET (Preset)
DISC (FOLDER)
8
0
Page: 9
10 CQ-C7405W
Preparation
For the first use, the following screen may appear
repeatedly.
1 Set your car's ignition switch to the ACC
or On position.
The demonstration screen appears.
2 Press [SOURCE] (PWR: POWER).
3 Press [MENU] to display the menu
display.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
4 Press []] or [[] to display the
DISPLAY menu.
5 Turn [VOL] to select
“DEMONSTRATION”.
For using the remote control, use [{] or [}].
6 Press [PUSH SEL] to select “OFF”.
For using the remote control, use [BAND] (SET).
7 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
Note: This unit is operable as usual even if the
demonstration screen is activated. The demonstration
screen automatically appears if no operation is executed
for 1 minute.
Cancellation
of
demonstration
screen
Remote
Control
Preparation
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Battery Replacement
q
w
q Remove the battery holder
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
2
3
w Put a battery in the case
with (+) side facing up.
e Put the case back.
Tough pointed object
Back side
Insulation film
Warning
Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Cautions
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Page: 10
11
English
CQ-C7405W
Note: Adjust the clock when “ADJUST” appears on the
display.
1 Press [MENU] to display the menu
display.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
2 Press []] or [[] to display the
DISPLAY menu.
3 Turn [VOL] to select “CLOCK ADJ”.
For using the remote control, use [{] or [}].
4 Press [PUSH SEL], and the clock
adjustment screen appears.
For using the remote control, use [BAND] (SET).
5 Adjust the setting value.
[[]: Adjusting minutes
[]]: Adjusting hours
q : Forward
w : Backward
6 Press [PUSH SEL], and the menu
screen resumes.
For using the remote control, use [BAND] (SET).
7 Press [MENU] to close the menu screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡ Subwoofer level adjustment (a page 26)
¡ Subwoofer low pass filter (a page 26)
The following functions are activated when the Security
Function is ON. (a page 27)
¡ The security indicator lights up when removing the
face plate.
¡ The alarm sounds and the message appears on the
screen to warn you to remove the face plate at ACC
off.
Security Indicator
Preparation
Security
Function
Setting
Other
Settings
Clock
adjustment
Page: 11
12 CQ-C7405W
Power on
Press [SOURCE] (PWR: POWER).
Power off
Hold down [SOURCE] (PWR: POWER) until
you hear a beep, then release it.
General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
You can remove the face
plate to prevent it from
being stolen.
Removing
1 Turn off the power (a page 12)
2 Press [ ]
(Release).
(The face plate disen-
gages with a click
when it is removed.)
The face plate automatically closes after a lapse of 5
seconds while it is open.
The power is automatically turned off while the unit
is active.
3 Put the face
plate in the case.
Mounting
1 Slide the left side of the face plate in
place.
2 Press the right end of the face plate
until “click” is heard.
Cautions
¡ It is recommended to remove or mount the face
plate when the plate is at the closed position.
Do not remove or mount the face plate when the
plate is in motion.
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high
levels.
¡ Do not touch the contacts on the face plate or on the
main unit, since this may result in poor electrical
contacts.
¡ If dirt or other foreign substances get on the con-
tacts, wipe them off with clean and dry cloth.
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
/
Power
On/off
(PWR:
POWER)
Face
Plate
Removing/Mounting
(ANTI-THEFT
SYSTEM)
Page: 12
13
English
CQ-C7405W
Open/Eject
Press [u OPEN].
When a disc is already loaded, the disc will automatically
be ejected.
Close
Press [u OPEN].
Tilt
The display angle changes among 4 levels as follows
every time you hold down [u OPEN] (TILT) for 1 sec.
or more and release.
Note: The last selected
angle is memorized even
after turning off the power.
Notes:
¡ The volume level can be set independently for each
source. (For radio, one volume setting for AM, one
volume setting for all FMs)
¡ The volume is not adjustable while an error or the
menu screen is present on the monitor.
¡ This unit memorizes individual volume levels for each
source. Make volume adjustments of each source
appropriately to prevent large volume fluctuation when
the source is changed.
q Up
w Down
Setting Range: 0 to 40
Default: 13
Volume off (down)
Press [MUTE].
Cancel
Press [MUTE] again.
Note: Volume-down range can be specified.
(a page 27)
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
General
Face
Plate
Motion
(Open/Close,
Tilt)
(OPEN/CLOSE,
TILT)
Volume
Adjustment
(VOLUME)
Temporary
Volume
Off
(Down)
MUTE
(ATT:
ATTENUATION)
Cautions
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
¡ Do not pinch your finger or hand in the face plate.
¡ Do not insert foreign objects into the disc slots.
¡ For the following cases, the face plate automatical-
ly closes. Use caution not to catch your finger.
¡ After a lapse of 20 seconds
¡ When a disc is inserted
¡ When the face plate is removed (a page 12)
¡ When ACC is set to off
TILT 1
TILT 2
TILT 3
OPEN
TILT OFF
Page: 13
14 CQ-C7405W
General (continued)
Radio
FM1, FM2, FM3, AM (a page 18)
Source
Selection
(SOURCE)
The source changes as follows every time
[SOURCE] is pressed.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Player
When loading CD (a page 20)
When loading a disc containing compressed
audio files (a page 22)
AUX 1
Device connected to the AUX terminal of the this unit
System-up Connector
Device connected to the System-up Connector of this
unit
When optional devices are connected:
Shift to connected devices
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated
in sequence after shifting to AUX2 (devices connected
to the AUX terminal of the expansion module).
When connecting DVD Changer
When connecting CD Changer
When connecting iPod
Note: For information about connectable devices, refer
to the System Upgrade Guidebook or the instruction
manual for each device.
When connecting Expansion Module
Page: 14
15
English
CQ-C7405W
General
The display changes as follows every time [DISP]
(DISPLAY) is pressed.
Note: The graphic pattern and still image are selectable.
(a page 29)
At power-off:
Clock display (default)
Mode
Folder hierarchy (Compressed Audio Player mode only)
Ordinary display + graphic pattern
Ordinary display + still image
Ordinary display + clock
Display OFF
All displays disappear in 5 seconds.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
At power-on:
Off
Only graphic pattern
Only still image
Display
Change
(DISP:
DISPLAY)
Note: The graphic equalizer of 19 bands (S.A.) is
selectable when selecting a graphic pattern.
Page: 15
16 CQ-C7405W
Sound Control
SRS and SQ that provide users with simple adjustment of sound quality are described on this page. Audio Setting (a page 26) allows
users to adjust each speaker and the optional subwoofer in more detail (regarding BASS, TREBLE, BALANCE, FADER, SUB.W, LPF,
HPF, REAR).
SRS
WOW
SRS
WOW
Setting
(SRS
WOW
Menu
Display)
SRS WOW™ is 3-D sound technology based on the HRTF
(Head Related Transfer Function) theory. Unlike
conventional audio systems, “natural 3-D sound field”,
“rich bass”, and “crisp and clear sound” can be obtained
at the same time in a wide area in front of speakers.
Holding down [VOL] (SRS WOW) for 2 sec. or more
toggles SRS WOW on and off.
Note: If you enable SRS WOW, the following functions
are automatically disabled:
SQ, BASS/TREBLE, BALANCE/FADER, HPF, SBC-SW
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Lights when SRS WOW is activated.
You can make a fine adjustment to SRS WOW.
1 Set the SRS WOW mode to on.
2 Hold down [SQ] for 2 sec. or more to
display “WOW MENU”.
3 Turn [VOL] to select a function to be
adjusted.
For using the remote control, use [}] or [{].
4 Press [PUSH SEL] to adjust.
For using the remote
control, use [BAND]
(SET).
5 Press [DISP:DISPLAY] to close the
menu screen.
SRS TruBass®
: Deep bass enhancement by application of the
bass reproduction technique of a pipe organ
(default)
: No enhancement
SRS FOCUS®
Sound image movement in a vertical direction to make
sound crisp
: high (default)
: low
: off
SRS®
: Surround function on (default)
: Surround function off
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license
from SRS Labs, Inc..
Page: 16
17
English
CQ-C7405W
Sound
Control
The equalizer curve is selectable from among preset 6
types (FLAT, ROCK, POP, VOCAL, JAZZ, and CLUB)
depending on your listening category.
Note: SQ is not changeable when SRS WOW is enabled.
(a page 16)
SQ changeover
The SQ category is changed every time [SQ] (SOUND
QUALITY) is pressed.
Note: Setting of SQ, bass/treble and volume are
influenced one another. If the influence mentioned above
causes distortion to the audio signal, readjust bass/treble
or volume. (a page 26) Lights when SQ is activated.
SQ is adjustable in accordance with your taste.
1 Hold down [SQ] (SOUND QUALITY) for 2
sec. or more to display “SOUND QUALITY
MENU” when SRS WOW is disabled.
2 Press [PUSH SEL].
The targeted SQ preset appears.
For using the remote control, use [BAND] (SET).
3 Adjust each band.
Band: 60, 160, 400, 1 k, 3 k, 6 k, 16 k (Hz)
[]] [[]: Band selection
q w: Level up/down
“USER” appears in the category name after adjust-
ment.
Note: If [PUSH SEL] is held down for 2 sec. or
more on the “SQ ADJUSTMENT” display, the preset
data that is called up can be turned into the default.
4 Press [PUSH SEL].
The screen of Step 1 appears again.
For using the remote control, use [BAND] (SET).
5 Press [DISP:DISPLAY].
The regular screen appears again.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
The rear speaker can be used as a substitutional
subwoofer when a subwoofer is not connected.
Holding down [SBC-SW] for 2 sec. or more
toggles SBC-SW on and off.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Lights when SBC-SW is activated.
Off (default)
On
SQ
Selection
Based
on
Genre
(SQ:
SOUND
QUALITY)
SQ
adjustment
(USER)
Substitutional
Subwoofer
(SBC-SW:
SUPER
BASS
CONTROL-SUBWOOFER)
Notes:
¡ If ON is selected, the settings of subwoofer level
adjustment and subwoofer low pass filter are activat-
ed. (a page 26)
¡ SBC-SW is not changeable when SRS WOW is
enabled. (a page 16)
Page: 17
18 CQ-C7405W
Radio
This chapter explains how to listen to the radio.
1 Press [SOURCE] to select the radio
mode.
2 Press [BAND] to select a band.
3 Select a station.
Frequency adjustment
[]] (TUNE): Lower
[[] (TUNE): Higher
Note: Hold down for 0.5 sec. or more and release
for station search.
Preset station selection
[{] (P-SET: Preset): Lower preset number
[}] (P-SET: Preset): Higher preset number
Notes:
¡ Direct selection can be executed with [1] to [6]
buttons on remote control.
¡ A preset station is selectable by turning [VOL]
while the preset list screen is present on the
monitor.
¡ The volume is not adjustable while the preset list
screen is present on the monitor.
Band Frequency
Preset Number
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Operation
Flow
You can assign your favorite broadcasting station to
the [D·M] button. As the result of doing that, your
favorite broadcasting station can be received even if
the unit is in the CD mode or other modes. (Default:
FM 87.50 MHz)
Note: For the use of an FM transmitter, it is useful
for users to register applicable frequencies on D·M
(DIRECT MEMORY).
D·M station Calling
Press [D.M] (DIRECT MEMORY).
D·M station Setting
q Select a station you would like to preset.
w Hold down [D.M] (DIRECT MEMORY) for 2 sec.
or more.
Note: If the unit is turned off during receiving a broad-
casting station via D·M, the unit starts again receiving
the broadcasting station via D·M by turning on the unit.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Direct
Memory
Lights while receiving an FM stereo signal.
Radio
Mode
Display
Page: 18
19
English
CQ-C7405W
Radio
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing [}]
(P-SET) or [{] (P-SET).
Notes:
¡ Direct selection can be executed with [1] to [6] but-
tons on remote control.
¡ You can switch between 6 and 18 for FM presetting
stations. (EACH BAND/ALL BAND)
¡ Preset stations are changeable. (Preset Swap)
Auto Preset Memory (APM)
Stations with good receiving conditions automatically
preset.
1 Select a band.
2 Hold down
[BAND] (APM)
for 2 sec. or
more.
The preset stations under best receiving conditions
are received for 5 sec. each after presetting the sta-
tions (SCAN). To stop scanning, press [}] or [{].
Note: New stations overwrite existing saved stations.
Manual station preset
1 Tune in to a station.
2 Hold down [}] or [{] for 2 sec. or
more.
3 Turn [VOL] to select a preset number.
4 Hold down [PUSH SEL] for 2 sec. or
more, and the frequency is stored at the
selected preset number.
Notes:
¡ In step 2, a station can be registered by holding down
the numeric button [1] to [6] for 2 sec. or more.
¡ To stop presetting stations, press [DISP]
(DISPLAY).
¡ The operation above allows users to replace the cur-
rent station with the station preset in the selected
number while selecting a preset station. (Preset Swap)
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
/
Radio
Menu
Display
1 Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Press [PUSH SEL] to adjust.
For using the remote
control, use [BAND]
(SET).
3 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
PRESET
Preset range for FM bands
: Individual setting for FM1-3 each
(default)
: Setting of FM1-3 together
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Station
Preset
(APM:
AUTO
PRESET
MEMORY
P-SET:
PRESET)
Page: 19
20 CQ-C7405W
CD Player
Cautions
¡ This unit does not support 8 cm discs.
¡ Do not use irregularly shaped discs. (a page 36)
¡ Do not use discs that have a seal or label attached.
¡ To avoid damaging the face plate, do not push it down or
place objects on it while it is open.
¡ Do not pinch your finger or hand in the face plate when the
face plate is in motion.
¡ Do not insert foreign matter into the disc slots.
¡ Refer to the section on “Notes on CD/CD Media (CD-ROM,
CD-R, CD-RW)” (a page 36).
¡ This unit does not support a MIX mode CD (a CD containing
both CD-DA and compressed audio data). In case of using
such a CD, problems may occur such as anacoustic play-
back.
When a disc is already loaded, press [SOURCE] to
select the CD mode.
1 Press [u OPEN] to open the face plate.
When a disc is already loaded ( lights), the disc
will automatically be ejected.
2 Load a disc with the printed side facing
up.
The face plate closes automatically, and the unit rec-
ognizes the disc and starts playing automatically,
too.
3 Select a desired portion.
Track selection
[7] (TRACK): Next track
[6] (TRACK): Preceding track (press twice)
Note: Hold down for fast forward/reverse.
Pause
Press [BAND] (h / 5).
Press again to cancel.
4 Press [u OPEN] to eject the disc.
Note: The panel automatically closes after 20 sec-
onds.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Track number Time
Lights when the disc is
loaded.
Play Mode indicators
Lights when each mode is
activated.
CD-TEXT display
Notes:
¡ For scrolling text, hold down [DISP: DISPLAY]
for 2 sec. or more.
¡ “NO TEXT” is displayed when there is no information
on the disc.
Operation
Flow
CD
Mode
Display
Printed side
Page: 20
21
English
CQ-C7405W
CD
Player
Random and Repeat play can be set.
1 Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2Turn [VOL] to select a function to be
adjusted.
For using the remote
control, use [}] or
[{].
3 Press [PUSH
SEL] to adjust.
For using the remote control, use [BAND] (SET).
4 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
RANDOM
: Off (default)
: Random playback
REPEAT
: Off (default)
: Playing the current track repeatedly
TEXT (CD-TEXT)
: Enabled (default)
: Disabled
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Play Mode Selection
One-touch operation is available for selecting a track
playing style by use of [RANDOM] or [REPEAT].
RANDOM
Press [RANDOM].
Press again to cancel.
REPEAT
Press [REPEAT].
Press again to cancel.
SCAN play
You can find your favorite track by playing first 10 sec. of
each track.
Press [SCAN].
Press again to cancel.
Direct Access
A track can be directly selected.
Example: track number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [SET].
Note: To suspend direct selection, press [DISP]
(DISPLAY).
Functions
Only
by
Remote
Control
Unit
Random,
Repeat
Play
(CD
Menu
Display)
(RANDOM,
REPEAT)
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Page: 21
22 CQ-C7405W
MP3/WMA/AAC Player
This unit can play MP3, WMA, and AAC files.
When a disc is already loaded, press [SOURCE] to
select the compressed audio mode.
1 Press [u OPEN] to open the face plate.
When a disc is already loaded ( lights), the disc
will automatically be ejected.
2 Load a disc with the printed side facing
up
The face plate closes automatically, and the unit rec-
ognizes the disc and starts playing automatically,
too. (It may take several minutes to start for a disc
that has a lot of files.)
3 Select a desired portion.
Folder selection
[}] (FOLDER): Next folder
[{] (FOLDER): Preceding folder
File selection
[7] (TRACK): Next file
[6] (TRACK): Preceding file (press twice)
Note: Hold down for fast forward/reverse.
Pause
Press [BAND] (h / 5).
Press again to cancel.
4 Press [u OPEN] to eject the disc.
Note: The panel automatically closes after 20 sec-
onds.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Folder number
Time
Lights when the disc is
loaded.
Play Mode indicators
Lights when each mode is
activated.
Information Display
Notes:
¡ For scrolling text, hold down [DISP: DISPLAY]
for 2 sec. or more.
¡ “NO TEXT” is displayed when there is no information
on the disc.
File number
File type indicator
(Folder Random)
(Folder Repeat)
(Folder Scan)
Printed side
Operation
Flow
Compressed
Audio
Player
Mode
Display
Page: 22
23
English
CQ-C7405W
MP3/WMA/AAC
Player
Notes:
¡ Refer to the pages 24 and 25 for cautions.
¡ This unit does not support a MIX mode CD (a CD containing both CD-DA and compressed audio files). In case of using such a
CD, problems may occur such as anacoustic playback.
Random and Repeat play can be set.
1 Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Turn [VOL] to select a function to be
adjusted.
For using the remote
control, use [}] or
[{].
3 Press [PUSH
SEL] to adjust.
For using the remote control, use [BAND] (SET).
4 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
RANDOM
: Off (default)
: Random playback (disc)
FOLDER RANDOM
: Off (default)
: Random playback (folder)
REPEAT
: Off (default)
: Playing the current file repeatedly
FOLDER REPEAT
: Off (default)
: Playing the current folder repeatedly.
TEXT
: Folder name/File name (default)
: Album/Title/Artist (tag information)
: No display
RE-MASTER
The high-range signal lost through MP3/WMA/AAC
compression is reproduced to more closely recreate the
pre-compressed sound.
Notes:
¡ At high bit rates, the Re-master function may have
little effect.
¡The Re-master function is only effective for playback
of MP3/WMA/AAC data.
: Digital sound enhancer activated (default)
: Digital sound enhancer inactivated
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Play Mode Selection
One-touch operation is available for selecting a file
playing style by use of [RANDOM] or [REPEAT].
RANDOM, REPEAT
Press the button. Press again to cancel.
FOLDER RANDOM, FOLDER REPEAT
Hold down the button for 2 sec. or more. Hold
down again to cancel.
SCAN play
You can find your favorite file by playing first 10 sec. of
each file.
SCAN (All files)
Press [SCAN]. Press again to cancel.
FOLDER SCAN (1st file in each folder)
Hold down [SCAN] for 2 sec. or more. Hold down
again to cancel.
Direct Access
A file in the current folder can be directly selected.
Example: file number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [SET].
Notes:
¡ For folder selection, enter a number after pressing [#]
(NUMBER) twice.
¡ To suspend direct selection, press [DISP]
(DISPLAY).
Random,
Repeat
Play
(Compressed
Audio
Player
Menu
Display)
(RANDOM,
REPEAT)
Functions
Only
by
Remote
Control
Unit
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Page: 23
24 CQ-C7405W
MP3/WMA/AAC Player (continued)
Cautions
as
to
compressed
audio
files
Cautions
as
to
the
display
of
this
unit
Each of MP3 (MPEG Audio Layer-3), WMA (Windows Media™ Audio), and AAC (Advanced Audio Coding) is a format
for compressed audio file. These formats allow users to save all the files contained in approximately 10 pieces of
existing CDs on one piece of CD-R/RW.
Note: Each of encoding software is not included with this unit.
Display Information
Displayable characters
¡ Displayable length of file name/folder name: within 64
characters. (Unicoded file and folder names are
reduced by half in the number of displayable charac-
ters.)
¡ Name files and folders in accordance with the stan-
dard of each file system. Refer to the instructions of
writing software for details.
¡ ASCII character set and special characters in each lan-
guage can be displayed.
ASCII character set
A to Z, a to z, digits 0 to 9, and the following sym-
bols:
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ
_ ` { | } ~
Notes:
¡ Characters may be garbled depending on encoding
software to be used
¡ Undisplayable characters and symbols will be convert-
ed into an asterisk (*).
¡ Common
Folder name,
File name
¡ MP3
Album name,
Title name/artist name
(ID3 tag)
¡ WMA
Album name,
Title name/artist name
(WMA tag)
¡ AAC
Album name,
Title name/artist name
(AAC tag)
Common
¡ High bit rate and high sampling frequency are recommended
for high quality sounds.
¡ Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
¡ The playback sound quality differs depending on the encod-
ing circumstances. For details, refer to the user manual of
your own encoding software and writing software.
¡ Be sure to put an extension compatible with the format.
MP3
¡ It is recommended to set the bit rate to “128 kbps or more”
and “fixed”.
WMA
¡ It is recommended to set the bit rate to “64 kbps or more”
and “fixed”.
¡ Do not set the copy protect attribute on the WMA file to
enable this unit to play back.
AAC
¡ It is recommended to set the bit rate to “128 kbps or more”
and “Stereo”.
¡Files with the extension of “.m4a” encoded using iTunes ver-
sion 6 are playable on this unit. Some of the files using
other encoders are not playable.
¡Files encoded using Apple Lossless Encoder are not
playable.
¡Files with copyright protection are not playable.
Caution
Never put an extension indicating compressed audio (such as “.mp3”, “.wma”, and “.m4a”) to
files other than compressed audio files. This may not only produce noise from the speaker
damage, but also damage your hearing.
Setting at file making
8, 11.205, 12, 16, 22.05,
24, 32, 44.1, 48 kHz
Yes
24 k – 320 kbps
MPEG 4 AAC LC
32, 44.1, 48 kHz
Yes
32 k – 192 kbps
Windows Media Audio Ver. 2, 7, 8, 9*
12, 11.205, 8 kHz
Yes
8 k – 160 kbps
MPEG 2.5 audio layer 3 (MP3)
16, 22.05, 24 kHz
Yes
8 k – 160 kbps
MPEG 2 audio layer 3 (MP3)
32, 44.1, 48 kHz
Yes
32 k – 320 kbps
MPEG 1 audio layer 3 (MP3)
Sampling frequency
VBR
Bit rate
Compression method
Compression formats
* WMA 9 Professional/LossLess/Voice are not supported.
Page: 24
25
English
CQ-C7405W
MP3/WMA/AAC
Player
Cautions
as
to
disc
making
Compressed audio file writing
¡ Do not save an audio file (CD-DA file) and a com-
pressed audio file on the same disc. Failure to
observe this may result in difficulty in playing.
¡ If compressed audio files formatted with two or
more types are saved on the same disc, each format
shall have a different folder.
¡ Do not write files other than compressed audio files.
¡ Playability may depend on the combination of writing
software and disc writer to be used.
¡ This unit does not support the play list function.
¡ Write files in a disc-at-once manner unless otherwise
needed.
¡ You can shorten the duration between data read and
playback by decreasing the quantity of files or folders,
or the depth of the hierarchy.
Supported file systems
ISO 9660 Level 1/Level 2/Level 3, Joliet, Romeo
Note: Apple HFS, UDF 1.50, Mix CD and CD Extra are
not supported.
Folder selection order/file playback order
Maximum number of files/folders
¡ Maximum number of files: 511 (files + folders)
¡ Maximum number of files in one folder: 255
¡ Maximum depth of trees: 8
¡ Maximum number of folders: 255 (Root folder is
included.)
Notes:
¡ This unit counts the number of folders irrespective of
the presence or absence of a compressed audio file.
¡ If the selected folder does not contain any com-
pressed audio file, the nearest compressed audio file
in the order of playback will play.
¡ Playback order of this unit may be different from that
of other compressed audio players even if the same
disc is used
¡ “ROOT” appears when displaying the root folder
name.
Root Folder
(Root Directory)
Folder Selection
File Selection
Tree 1 Tree 2 Tree 3 Tree 4 Tree 8
(Max.)
2
1
3
4
q
q
w
e
r
t
y
y
5
6
8
1 8
7
–
In the order
–
In the order
Copyright
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself
personally.
No warranty
Above description complies with our investigations as of
October 2006. It has no warranty for reproducibility and
displayability of MP3/WMA/AAC.
Common
iTunes is a trademark of Apple Computer, Inc.,
registered in the U.S. and other
countries/regions.
Windows Media, and the
Windows logo are trademarks
or registered trademarks of
Microsoft Corporation in the
United States and/or other
countries/regions.
MPEG Layer-3 audio coding technology licensed
from Fraunhofer IIS and Thomson.
Page: 25
26 CQ-C7405W
Audio Setting
Adjustment to each speaker and an optional subwoofer
VOLUME
Main volume adjustment
(Setting range: 0 to 40, Default: 13)
q : Up
w : Down
BASS / TREBLE
Bass adjustment
(Setting range: -12 dB to +12 dB, 2 dB Step, Default:
Bass 0 dB)
q : Up
w : Down
BASS / TREBLE
Treble adjustment
(Setting range: -12 dB to +12 dB, 2 dB Step, Default:
Treble 0 dB)
q : Up
w : Down
Note: Do not activate SQ and Bass/Treble at same time
to avoid causing sound distortion.
BALANCE / FADER
Balance adjustment
(Setting range: L (left)15 to R (right) 15 and Center,
Default: Center)
q : Right enhanced
w : Left enhanced
BALANCE / FADER
Fader adjustment
(Setting range: R (rear) 15 to F (front) 15 and Center,
Default: Center)
q : Front enhanced
w : Rear enhanced
SUB WOOFER
Subwoofer level adjustment
(Setting range : mute (-∞), -6 dB to +6 dB, 2 dB Step,
Default: 0 dB)
q : Up
w : Down
LPF
Low Pass Filter
(Setting range: 80 Hz, 120 Hz, 160 Hz, Default: 80 Hz)
q : Up
w : Down
HPF
High Pass Filter
(Setting range: Filter OFF, 90 Hz, 135 Hz, 180 Hz, 225 Hz,
Default: Filter OFF)
q : Up
w : Down
REAR (SRS WOW)
Rear Level Adjustment
(Setting range: 0 to –15, Default: –10)
q : Up
w : Down
Note: The rear level is adjustable only when SRS WOW
is enabled. (a page 16)
Subwoofer output range
Other speakers output ranges
AUDIO
Menu
Display
1 Press [PUSH
SEL: Select] to
display the
AUDIO menu
display.
For using the remote control, use [SEL] (MENU).
2 Press [PUSH SEL: Select] to select a
mode to be adjusted.
For using the remote control, use [SEL] (MENU).
3 Turn [VOL]
clockwise or
counterclockwise
to adjust.
For using the remote
control, use [}] or [{].
Note: Only the VOLUME, SUB.W, LPF, and REAR are
adjustable when SRS WOW is enabled. (a page 16)
Page: 26
27
English
CQ-C7405W
Function Setting
Adjustment to display on the FUNCTION menu
Audio
Setting,
Function
Setting
FUNCTION
Menu
Display
1 Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Press []] or [[] to display the FUNC-
TION menu.
3 Turn [VOL] to select a function to be
adjusted.
For using the remote
control, use [}] or
[{].
4 Press [PUSH
SEL] to adjust.
For using the remote control, use [BAND] (SET).
5 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
MUTE KEY
Setting [MUTE] buttons’ functions
: Volume off (default)
: Volume down by 10 steps
: Volume down by 5 steps
EXT.MUTE (External Mute)
Volume adjustment when an interruption such as car
navigation signal occurs
: Volume off (default)
: Volume down by 10 steps
: Volume down by 5 steps
: No change in volume
SECURITY
Setting the security function (a page 11)
: ON (default)
: OFF
BUILT-IN AMP
You can toggle the integrated amplifier on and off.
: Amplifier on (default)
: Amplifier off (when the external amplifier is used)
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
lights when disactivated.
(External muting display)
Page: 27
28 CQ-C7405W
Display Setting
Adjustment to display on the DISPLAY menu
1 Press [MENU] to display the menu
display.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Press []] or [[] to display the
DISPLAY menu.
3 Turn [VOL] to select a function to be
adjusted.
For using the remote
control, use [}] or
[{].
4 Press [PUSH
SEL] to adjust.
For using the remote control, use [BAND] (SET).
5 Adjust the setting value.
6 Press [PUSH SEL].
For using the remote control, use [BAND] (SET).
7 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
COLOR
(Setting range: 10 types, default: STORM)
The illumination color changes as follows.
Turn [VOL] to make a selection.
STORM: The color varies in conjunction with time.
LEVEL: The peripheral color decoration lights up and
goes out according to the bass volume.
FIRE: Red
ORANGE: Amber
SKY: Blue
OCEAN: Aquablue
FOREST: Green
SUN: Yellow
SNOW: White
CUSTOM: You can create your favorite color.
DEMONSTRATION
Switching by [PUSH SEL].
ON: Demonstration screen at no operation
(default)
OFF: Regular screen
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
LEVEL ADJ
When LEVEL is setting in COLOR types, you can make a
fine adjustment in the LEVEL ADJ display.
[]][[]: Function selection
Turn [VOL] to make a selection.: Item selection
Color selection
The illumination color changes.
(Setting range: FIRE, ORANGE, SKY, OCEAN, FOREST,
SUN, default: FIRE)
Volume setting according to lighting
(Setting range: LEVEL1, LEVEL2, LEVEL3, default: LEVEL
1)
If the peripheral color decoration keeps lighting because
the bass part is contained abundantly, select LEVEL 1,
and for the opposite case, select LEVEL 3.
DISPLAY
Menu
Display
Page: 28
29
English
CQ-C7405W
Display
Setting
DISPLAY
Menu
Display
(continued)
GRAPHIC PATTERN
(Default: All)
Turn [VOL] to make a selection.
All: Sequential display from pattern A to C.
Pattern A-C
S.A.: 19-band display (Spectrum analyzer)
CUSTOM ADJ
When CUSTOM is setting in COLOR types, you can make
a fine adjustment in the CUSTOM display.
(Setting range: 0 to 100, default: R50, G50, B50)
You can adjust each color.
[]][[]: RGB selection
Turn [VOL] to make a selection.: Adjustment (0 to 100)
SCREEN
Press [PUSH SEL] to select.
: white background (default)
: black background
STILL IMAGE
(Default: All)
Turn [VOL] to make a selection.
All: Sequential display from pattern 1 to 10
No.1-10
CONTRAST
(Setting range: 1 to 5, Default: Contrast 3)
Turn [VOL] to make a selection.
CLOCK ADJ
Note: Adjust the clock when “ADJUST” appears on the
display.
[[] : Adjusting minutes
[]] : Adjusting hours
q : Forward
w : Backward
Notes:
¡ The graphic pattern and still image are changeable.
(a page 30)
¡ If corrupted data is selected, “DISPLAY FILE INCOM-
PLETE” appears. (a page 31)
Page: 29
30 CQ-C7405W
Customize the Display (Customize Function)
You can edit the moving images and still images that are initially stored in the unit. You also can use the data that is downloaded from
the Panasonic Web site and the data that is stored with a digital camera or other devices and processed with exclusive software,
IMAGE STUDIO. See “Notes on Customize function” (a page 31) as well.
Note: Visit Panasonic Web site (http://panasonic.co.jp/pas/en/software/customize/index.html) for details.
CUSTOMIZE
Menu
Display
Preparation:
Put the CD-R/RW that contains data to
be customized in hand.
1 If there is a disc inside, take out the
disc.
2 Press [SOURCE]
to select the CD
mode.
3 Hold down [PUSH SEL] for 4 sec. or
more to display the menu screen.
4 Load a CD-R/RW that contains data.
Note:
¡ It may take time for the unit to identify the CD-
R/RW.
¡ Discs recorded by the packet writing software are
not supported.
5 Select an item to be customized.
q w: Select
[PUSH SEL]:Confirm
Note: To exit the customize menu, hold down
[PUSH SEL] for 4 sec. or more.
GRAPHIC PATTERN
Moving image (graphic pattern) data (a page 29)
STILL IMAGE
Still image data (a page 29)
OPENING MESSAGE
Moving image at power on
CLOSING MESSAGE
Moving image at power off
6 Select a file.
q w []][[]: Select
[PUSH SEL]: Confirm
Notes:
¡ Files are automatically identified by their exten-
sions, and target files are displayed.
¡ If “BACK” is selected, the screen of step 5
appears.
7 For a moving image file or still image
file, select where to save the file.
q w [}][{]:Select
[PUSH SEL]: Confirm
Notes:
¡ New data overwrites existing data.
¡ If “BACK” is selected, the screen of step 6
appears.
8 Confirm the changed item.
q w: Select
[PUSH SEL]: Confirm
Customization is performed. Do not turn off the
power in mid-operation. (It takes approx. 1 minutes
to complete this operation for a 168 kB moving
image.) After completion of this operation, the
screen of step 5 appears.
Note: If “NO” is selected, the screen of step 5
appears.
9 Press [u OPEN] to eject the disc.
10Hold down [PUSH SEL] for 4 sec. or
more.
The CD mode comes back.
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Page: 30
31
English
CQ-C7405W
Notes
on
Customize
Function
Note on Download Service
The download service may be suspended or stopped
without advance notice. The download service is not
available in some areas. Please visit the site below for
further information.
Panasonic Web site: (http://panasonic.net)
Notes on IMAGE STUDIO
¡ This download service is not available in some areas.
For details, please access the Panasonic website.
¡ IMAGE STUDIO is available only by downloading from
the address below. It is not bundled with this unit.
¡ Refer to the downloaded operating manual for how to
use IMAGE STUDIO.
Notes on File
¡ The customize-specific file is downloadable from the
URL below. You can create exclusive files stored with
a digital camera or other devices by using exclusive
software, IMAGE STUDIO that can be accessed from
the same URL.
¡ Do not change the extension. Otherwise, the data can-
not be recognized.
At Disc Making
¡ Save only customize-specific data.
¡ Save all data in the root directory. Files contained in a
folder cannot be recognized.
¡ Follow the table below with regard to the number of
files that are saved to a disc. Files beyond the speci-
fied capacity are not readable.
¡ Discs recorded by the packet writing software are not
supported.
At Customizing
¡ If customizing is interrupted on account of turning off
the power, stopping the engine, removing the face
plate or other reasons, you may lose the data. In such
a case, try customizing again.
¡ The default image exists on the Panasonic Web site. If
you would like to restore it, download the image from
the site.
Error Display Messages
NO FILES DETECTED
No customize-specific data on the disc
a Load a disc that contains customize-specific
data.
CUSTOMIZING FAILED
Customize failed
a Check to see whether or not the extension is cor-
rect and file contents are appropriate.
DISPLAY FILE INCOMPLETE
Intended moving image or still image is damaged.
a Customize it again and overwrite the file with
new one.
Type Extension Max. number
GRAPHIC PATTERN .pfm 10
STILL IMAGE .pfs 15
OPENING MESSAGE .pfo 5
CLOSING MESSAGE .pfe 5
Download site:
http://panasonic.co.jp/pas/en/software/
customize/index.html
Customize
the
Display
(Customize
Function)
Page: 31
32 CQ-C7405W
If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is
recommended to take the unit to your nearest authorized Panasonic
Service Center. The product should be serviced only by qualified
personnel. Please refer the checking and the repair to professionals.
Panasonic shall not be liable for any accidents arising out of neglect of
checking the unit or your own repair after your checking.
Never take measures especially for those other than indicated by ital-
ic letters in “Possible Solution” described below because those are
too dangerous for users to handle themselves.
Warning
¡ Do not use the unit in an irregular condition, for
example, without sound, or with smoke or a foul
smell, which can cause ignition or electric shock.
Immediately stop using the unit and consult your
dealer.
¡ Never try to repair the unit by yourself because it is
dangerous to do so.
Problem Possible cause a Possible solution
Common
No power to the
unit
The power cord (battery, power and ground) is connected in the wrong way.
a Check the wiring.
Fuse blows out.
a Eliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
Sound is not
generated.
MUTE is set to ON.
a Set MUTE to OFF.
The wiring of speaker lines are not correct, or a break or poor contact arises.
a Check the wiring in accordance with the wiring diagram. (Installation
Instructions)
Noise
There is an electromagnetic-wave generator such as a cellular phone near the unit or
its electrical lines.
a Keep an electromagnetic-wave generator such as a cellular phone away from
the unit and the wiring of the unit. In case that noise cannot be eliminated
due to the wiring harness of the car, consult your dealer.
The contact of the ground lead is poor.
a Make sure that the ground lead is connected to an unpainted part of the chas-
sis securely.
Noise is made in
step with engine
revolutions.
Alternator noise comes from the car.
a Change the wiring position of the ground lead.
a Mount a noise filter on the power supply.
Troubleshooting
Page: 32
33
English
CQ-C7405W
Common
(continued)
Some operations
are not executable.
Some operations are not executable in particular modes such as menu mode.
a Read the operating instructions carefully and cancel the mode. If the unit is
still out of order, consult your dealer.
Problem Possible cause a Possible solution
No sound from
speaker(s)
BALANCE/FADER setting is not appropriate.
a Readjust BALANCE/FADER.
There is a break, a short circuit, poor contact or wrong wiring regarding the speaker
wiring.
a Check the speaker wiring.
The speaker
channels are
reversed between
right and left.
The speaker wiring is confused between right and left.
a Perform the speaker wiring in accordance with the wiring diagram.
The sound field is
not clear in the
stereo mode.
Central sound does
not settled.
The plus and minus terminals at right and left channels of speakers are connected
reversely.
a Perform the speaker wiring in accordance with the wiring diagram.
Radio
Poor reception or
noise
Antenna installation or wiring of antenna cable is faulty.
a Check whether the antenna mounting position and its wiring are correct. In
addition, check to see whether the antenna ground is securely connected to
the chassis.
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
a Check the wiring of the antenna battery lead.
The power fails
unintentionally.
The safety device works.
a Consult your dealer, or your nearest Panasonic Service Center.
The number of auto
preset stations is
less than 6.
The number of receivable stations is less than 6.
a Move to an area where receivable stations number is maximum, and try pre-
setting.
Preset stations
cannot be stored.
The contact of the battery lead is poor, or the battery lead is not always powered.
a Make sure that the battery lead is connected securely, and preset stations
again.
Troubleshooting
Page: 33
34 CQ-C7405W
Troubleshooting (continued)
Remote
control
unit
No response to
pressing buttons
The battery is inserted in the wrong direction. A wrong battery is inserted.
aInsert a correct battery in the correct direction.
The battery is weak.
aReplace the battery with new one.
The aiming direction of the remote control unit is wrong.
aAim the remote control unit at the sensor of the unit and press buttons.
The sensor is exposed to direct sunlight. (The remote control unit may not be
operable when the sensor is exposed to direct sunlight. In such a case, the
system is not faulty.)
aBlock off sunlight to the sensor.
Problem Possible cause a Possible solution
No playback or
disc ejected
The disc is inserted upside down.
a Insert a disc correctly.
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc.
Sound skipping or
noise
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc.
Sound skipping
due to vibration
The unit is not sufficiently secured.
a Secure the unit to the console box.
The unit is tilted at over 30˚ in the front-to-end direction.
a Make the angle 30˚ or less.
Disc unejectable
Something such as a peeled label obstructs the disc coming out.
a Press and hold the [u OPEN] for more than 2 seconds when the face plate is
open (disc forced ejection). In case that the disc forced ejection does not
work, consult your dealer.
The microcontroller in the unit operates abnormally due to noise or other factors.
a Unplug the power cord and plug it again. In case the unit is still out of order,
consult your dealer.
CD
The CD-R/RWs that
are playable on other
devices are not
playable on this unit.
The playability of some CD-R/RWs may depend on the combination of media,
recording software and recorder to be used even if these CD-R/RWs are playable on
other devices such as a PC.
a Make CD-R/RWs in different combination of media, recording software and
recorder after referring to the description about the compressed audio player.
Sound skipping or
noise
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc.
Playing VBR (Variable Bit Rate) files may cause sound skipping.
a Play Non-VBR files.
Noise is heard with
“RE-MASTER” at
“ON”
With some CDs, noise may be heard in the treble range when playing compressed
audio files into which the CD tracks were encoded with “RE-MASTER” enabled.
a If noise is heard, set “RE-MASTER” to “OFF”.
Compressed
audio
No playback or
disc ejected
The disc has unplayable formatted data.
a Check the file format.
Page: 34
35
English
CQ-C7405W
Troubleshooting,
Error
Display
Messages
Error Display Messages
The player for some reason cannot read the file you are trying to play. (File recorded
in an unsupported file system, compression scheme, data format, file name exten-
sion, damaged data, etc.)
a Select a file that the player can read. Check the type of data recorded on the
disc. Create a new disc if necessary.
(After 5 seconds)
To next file automatically
The disc is dirty, or is upside down.
a Check the disc.
The disc has scratches.
a Check the disc.
No operation by some cause.
a Unplug the power cord and plug it again. In case the unit is still out of order,
consult your dealer. (a Installation Instructions)
A WMA file can be copyrighted.
a The file protected by copyright is not playable.
No disc.
Display Possible cause a Possible solution
Note: Refer to the System Upgrade Guidebook for error messages regarding optional products.
CD/Compressed
audio
Page: 35
36 CQ-C7405W
Notes on Discs
How to hold the disc
¡ Do not touch the underside of the disc.
¡ Do not scratch on the disc.
¡ Do not bend the disc.
¡ When not in use, keep the disc in a case.
Do not leave discs in the following places:
¡ In direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ On seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not write on the disc label with a ballpoint
pen or other hard-point pens.
If you use commercial CDs, they must have
either of these labels shown at right.
Some copy-protected music CDs are not
playable.
TEXT
¡ You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage them and make playback impossible.
¡ Some CD-R/RWs can not be played back successfully thanks to incompatibility among writing software, a CD
recorder (CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is not closed.
¡ This player cannot play the CD-R/RW discs which contains other than CD-DA or compressed audio data.
¡ Be sure to observe the instructions of CD-R/RW disc for handling it.
Notes
on
CD/CD
Media
(CD-ROM,
CD-R,
CD-RW)
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for
routine exterior cleaning. Never use benzine, thinner, or other solvents.
Notes
on
CD-Rs/RWs
Maintenance/Fuse
Cleaning
the
Unit
Fuse
If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Service Center.
Warning
¡Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the
unit directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your
nearest authorized Panasonic Service Center.
Discs with cracks, scratches
or parts missing
Disc with adhered stickers
or tape
Irregularly shaped discs
Labels created by a printer,
Protective films or sheets
<Correct> <Wrong>
Printed side
Page: 36
37
English
CQ-C7405W
Specifications
Notes
on
discs,
Maintenance/Fuse,
Specifications
Notes:
¡Specifications and design are subject to modification without notice due to improvements.
¡Some figures and illustrations in this manual may be different from your product.
General
Sampling Frequency 8 times oversampling
DA Converter 4 DAC System
Pick-Up Type Astigma 3-beam
Light Source Semiconductor laser
Wavelength 790 nm
Frequency Response 20 Hz – 20 kHz (±1 dB)
Signal to Noise Ratio 96 dB
Total Harmonic Distortion 0.01 % (1 kHz)
Wow and Flutter Below measurable limits
Channel Separation 85 dB
FM
Frequency Range 87.50 MHz – 108.00 MHz
Usable Sensitivity 6 dB/µV(S/N 30 dB)
Stereo Separation 30 dB (at 1 kHz)
AM
Frequency Range 531 kHz – 1 602 kHz
Usable Sensitivity 28 dB/µV (S/N 20 dB)
CD
Player
Power Supply DC 12 V (11 V – 16 V), Test Voltage 14.4 V, Negative Ground
Tone Controls (Bass/Treble) Bass; ±12 dB at 60 Hz, Treble; ±12 dB at 16 kHz
Equalizer Center Frequency 60, 160, 400, 1 k, 3 k, 6 k, 16 k Hz
Variable Range of Equalizer -12 dB to 12 dB (2 dB step)
Current Consumption Less than 2.2 A (CD mode, 0.5 W 4-Speaker)
Maximum Power Output 50 W x 4 (at 1 kHz)
Power Output 18 W x 4 CH (1 kHz, 1 %, 4 Ω)
Speaker Impedance 4 – 8 Ω
Pre-amp output voltage 5 V (CD mode, 1 kHz, 0 dB)
Subwoofer-output voltage 5 V (CD mode, 1 kHz, 0 dB)
Pre-amp output impedance 60 Ω
Subwoofer-output impedance 60 Ω
Dimensions (Main Unit) 178(W) x 50(H) x 155(D) mm
Weight (Main Unit) 1.6 kg
Radio
Page: 39
YFM284C664CA NY1006-1116 Printed in China
Matsushita Electric Industrial Co., Ltd.
Web Site : http://panasonic.net
CQ-C7405W
Page: 40
CQ-C7405W Installation Instructions YFM294C092CA (1)
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
4 e
w
TEXT
How to install the unit/ä‡Í ÒÏÓÌÚËÓ‚‡Ú¸ ÔË·Ó/
Installation/åÓÌÚ‡Ê/
Mounting collar q insertion. Bend mounting tabs.
ÇÒÚ‡‚ÎÂÌË ÏÓÌÚ‡ÊÌÓÈ ‡Ï˚ q. ᇄ˷‡˛Ú ÏÓÌÚ‡ÊÌ˚ ·ÔÍË.
q
Connection of power connector y
èÓ‰ÒÓ‰ËÌÂÌË ÒËÎÓ‚Ó„Ó ‡Á˙Âχ y
y
5
Trim plate u mounting
ìÒÚ‡Ìӂ͇ Ó·‡ÏÎÂÌËfl u
u
6
Battery cable reconnection
èÓ‚ÚÓÌÓ ÔÓ‰ÒÓ‰ËÌÂÌË ͇·ÂÎfl Í ·‡Ú‡ÂÂ
How to remove the unit/ä‡Í ÒÌflÚ¸ ÔË·Ó/
Cautions ● Wear gloves for safety.
● Make sure that wiring is completed
before installation.
ÇÌËχÌË ● ëΉÛÂÚ Ì‡‰ÂÚ¸ ÔÂ˜‡ÚÍË ‰Îfl
·ÂÁÓÔ‡ÒÌÓÒÚË.
● ëΉÛÂÚ Û·Â‰ËÚ¸Òfl, ˜ÚÓ ÏÓÌÚ‡Ê
˝ÎÂÍÚÓÔÓ‚Ó‰ÓÍ Á‡‚Â¯ÂÌ ‰Ó
ÏÓÌڇʇ ÔË·Ó‡.
●
●
Remove the cable from the battery negative terminal.
éÚÒÓ‰ËÌfl˛Ú ͇·Âθ ÓÚ ÓÚˈ‡ÚÂθÌÓ„Ó ‚˚‚Ó‰‡ ·‡Ú‡ÂË.
Bend appropriate tabs to secure the unit
without backlash.
ᇄ˷‡ÌËÂÏ ÒÓÓÚ‚ÂÚÒÚ‚Û˛˘Ëı ·ÔÓÍ ÙËÍÒËÛ˛Ú
ÔË·Ó ·ÂÁ Á‡ÁÓ.
q Screw the mounting bolt w into the main unit.
w Secure to the fire wall.
e Snap the right and left springs into each hole.
q ᇂÂÚ˚‚‡˛Ú mÓÌÚ‡ÊÌ˚È ·ÓÎÚ w ‚ „·‚Ì˚È ·ÎÓÍ.
w äÂÔÎÂÌËÂ Í ÚÂÔÎÓËÁÓÎflˆËÓÌÌÓÈ Ô‡ÌÂÎË.
e Ç‚Ó‰flÚ Ô‡‚Û˛ Ë ÎÂ‚Û˛ ÔÛÊËÌ˚ ‚ ÓÚ‚ÂÒÚËfl ÔÓ‰ ÌËı.
q w
w
e
Main unit securing
äÂÔÎÂÌË „·‚ÌÓ„Ó
·ÎÓ͇
4
Securing to fire wall
äÂÔÎÂÌËÂ Í ÚÂÔÎÓËÁÓÎflˆËÓÌÌÓÈ Ô‡ÌÂÎË
Using the rear support strap i
ë ÔÓÏÓ˘¸˛ Á‡‰ÌÂÈ ÓÔÓÌÓÈ Ô·ÌÍË i
i
Using the rubber bushing (Option)
ë ÔÓÏÓ˘¸˛ ÂÁËÌÓ‚ÓÈ ‚ÚÛÎÍË (ÔÓ ÓÔˆËË)
3mm
Tapping screw r
ë‡ÏÓ̇ÂÁ‡˛˘ËÈ ‚ËÌÚ r
r
To the unit
ä ÔË·ÓÛ
To the unit
ä ÔË·ÓÛ
Rear support strap i
ᇉÌflfl ÓÔÓ̇fl Ô·Ì͇ i
i
Hexagonal nut t
òÂÒÚË„‡Ì̇fl „‡È͇ t
t
Rear support bracket
(supplied with car)
ᇉÌËÈ ÓÔÓÌ˚È ÍÓ̯ÚÂÈÌ
(ÔÓÒÚ‡‚ÎflÂÏ˚È Ò ‡‚ÚÓÏÓ·ËÎÂÏ)
Rubber Bushing (Option)
êÂÁËÌÓ‚‡fl ‚ÚÛÎ͇ (ÔÓ ÓÔˆËË)
Mounting Bolt w
åÓÌÚ‡ÊÌ˚È ·ÓÎÚ w
w
Caution
When this unit is installed in dashboard,
ensure that there is sufficient air flow
around the unit to prevent damage from
overheating, do not block any ventilation
holes on the unit.
ÇÌËχÌËÂ
èË ÏÓÌڇʠ̇ÒÚÓfl˘Â„Ó ÛÒÚÓÈÒÚ‚‡ ̇ Ô‡ÌÂθ
ÔË·ÓÓ‚ ÒΉÛÂÚ Ó·ÂÒÔ˜ËÚ¸ ‰ÓÒÚ‡ÚÓ˜Ì˚È ÔÓÚÓÍ
‚ÓÁ‰Ûı‡ ‚ÓÍÛ„ ÌÂ„Ó ‚Ó ËÁ·ÂʇÌË „Ó
ÔÓ‚ÂʉÂÌËfl ËÁ-Á‡ ÔÂ„‚‡, Ô˘ÂÏ ÌÂ
ÒΉÛÂÚ Á‡Í˚‚‡Ú¸ ‚ÂÌÚËÎflˆËÓÌÌ˚ ÓÚ‚ÂÒÚËfl
ÛÒÚÓÈÒÚ‚‡.
Mounting Bolt w
åÓÌÚ‡ÊÌ˚È ·ÓÎÚ w
w
Remove the face plate.
ëÌËχ˛Ú ÎËˆÂ‚Û˛ Ô‡ÌÂθ
ÔË·Ó‡.
1
Remove the trim plate u.
ëÌËχ˛Ú Ó·‡ÏÌÂÌË u.
u
2
3
Pull out the unit with
both hands.
Ç˚Ú‡ÒÍË‚‡˛Ú Ó·ÂËÏË
Û͇ÏË ÔË·Ó.
4
Clank!
1
2
3
4
4
4
5
6
q
4
Lock release
q Insert the lock cancel plate
e until you hear a click.
w Pull the main unit.
ëÌflÚË ÒÚÓÔÓÂÌËfl
q ÇÒÚ‡‚Îfl˛Ú Ô·ÒÚËÌÛ ÒÌflÚËfl
ÒÚÓÔÓÂÌËfl e ‰Ó ˘ÂΘ͇.
w TflÌËÚe „Îa‚ÌÛ˛ e‰ËÌˈÛ.
q
e
w
0 – 30°
53 mm
182 mm
4.5 mm – 6.0 mm
AAC WMA MP3 CD Player/Receiver
AAC WMA MP3 CD-ÔÎÂÂ/ÂÒË‚Â
Model: CQ-C7405W
●Please read these instructions carefully before using this product and keep this manual for future reference.
●èÂ‰ ̇˜‡ÎÓÏ ˝ÍÒÔÎÛ‡Ú‡ˆËË ÔÓÒËÏ ÔÓ˜ËÚ‡Ú¸ ̇ÒÚÓfl˘Û˛ ËÌÒÚÛÍˆË˛ ‚ÌËχÚÂθÌÓ Ë ı‡ÌËÚ¸  ̇ ÔÓθÁÓ‚‡ÌË ̇ ·Û‰Û˘ÂÂ.
●
YFM294C092CA NY1006-1116 Printed in China
Matsushita Electric Industrial Co., Ltd.
Web Site: http://panasonic.net
Consult a professional for installation.
●Verify the radio using the antenna and speakers before installation.
èÓ ‚ÓÔÓÒÛ ÏÓÌڇʇ ÒΉÛÂÚ Ó·‡˘‡Ú¸Òfl Í ÒÔˆˇÎËÒÚÛ.
●èÂ‰ ÏÓÌÚ‡ÊÓÏ ÔÓ‚Âfl˛Ú ‡‰ËÓÔËÂÏÌËÍ Ò ÔÓÏÓ˘¸˛
‡ÌÚÂÌÌ˚ Ë „ÓÏÍÓ„Ó‚ÓËÚÂÎÂÈ.
●
●Mounting angle side to side : horizontal
front to rear : 0 – 30°
●ì„ÓÎ ÏÓÌڇʇ ‚ ÔÓÔÂ˜ÌÓÈ ÔÎÓÒÍÓÒÚË : ÉÓËÁÓÌڇθ
‚ ÔÓ‰ÓθÌÓÈ ÔÎÓÒÍÓÒÚË : 0 – 30°
●
°
●Mounting space
●èÎÓ˘‡‰¸ ÔÓ‰ ÏÓÌÚ‡Ê
●
Before Installation/èÂ‰ ÏÓÌÚ‡ÊÓÏ/ Before Wiring/èÂ‰ ÏÓÌÚ‡ÊÓÏ ˝ÎÂÍÚÓÔÓ‚Ó‰ÓÍ/
Supplied Hardware/ÑÂÚ‡ÎË, ‚ıÓ‰fl˘Ë ‚ ÍÓÏÔÎÂÍÚ‡ˆË˛ ÔÓÒÚ‡‚ÍË/
Exclusively operated with 12 V battery with
negative (–) ground.
Connect the power lead (red) last.
Connect the battery lead (yellow) to the positive (+) terminal of
the battery or fuse block terminal (BAT).
Strip about 5 mm of the lead ends for connection.
Apply insulating tape to bare leads.
Secure loosened leads.
ꇷÓÚ‡ÂÚ ÚÓθÍÓ Ò ÔËÚ‡ÌËÂÏ ÓÚ 12 V {B} ·‡Ú‡ÂË
Ò ÓÚˈ‡ÚÂθÌÓÈ (–) ÁÂÏÎÂÈ.
èÓ‰ÒÓ‰ËÌfl˛Ú ÒËÎÓ‚ÓÈ ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ (Í‡ÒÌ˚È) ÔÓÒΉÌËÏ.
èÓ‰ÒÓ‰ËÌfl˛Ú ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ (ÊÂÎÚ˚È) Í ÔÓÎÓÊËÚÂθÌÓÏÛ (+) ‚˚‚Ó‰Û
·‡Ú‡ÂË ËÎË ÍÎÂÏÏ ·ÎÓ͇ Ô·‚ÍËı Ô‰Óı‡ÌËÚÂÎÂÈ (BAT).
ë ÍÓ̈ӂ ‚˚‚Ó‰Ì˚ı ÔÓ‚Ó‰Ó‚ ÒÌËχ˛Ú ËÁÓÎflˆË˛ ̇ ‰ÎËÌ ÓÍÓÎÓ 5
mm {ÏÏ} ‰Îfl ÒÓ‰ËÌÂÌËfl.
ç‡ Ó·Ì‡ÊÂÌÌ˚ ‚˚‚Ó‰Ì˚ ÔÓ‚Ó‰‡
̇Í·‰˚‚‡˛Ú ËÁÓÎflˆËÓÌÌÛ˛ ÎÂÌÚÛ.
îËÍÒËÛ˛Ú ÓÒ··ÎÂÌÌ˚ ‚˚‚Ó‰Ì˚ ÔÓ‚Ó‰‡.
–
English
êÛÒÒÍËÈ
* w, e, r and t consist of a set. (YEP0FZ5739) * w, e, r Ë t ÒÓÒÚ‡‚Îfl˛Ú ÍÓÏÔÎÂÍÚ. (YEP0FZ5739)
* w, e, r t (YEP0FZ5739)
Remove mounting collar q and trim plate u from the main
unit temporarily, which are already mounted at shipment.
ÇÂÏÂÌÌÓ ÒÌËχ˛Ú Ò „·‚ÌÓ„Ó ·ÎÓ͇ ÔË·Ó‡ ÏÓÌÚ‡ÊÌÛ˛ ‡ÏÛ q Ë
Ó·‡ÏÎÂÌË u, ÒÏÓÌÚËÓ‚‡ÌÌ˚ ÔË ÓÚ„ÛÁÍÂ.
q u
Snapping point
MoÏeÌÚaθÌ˚È cÌËÏoÍ
ÔÛÌÍÚa
q
w
q
w
1
No. Diagram Q'ty
Item No. Diagram Q'ty
Item
Mounting collar
åÓÌÚ‡Ê̇fl ‡Ï‡
Mounting bolt (5 mmø)
åÓÌÚ‡ÊÌ˚È ·ÓÎÚ (5 mm {ÏÏ} ø)
ø
Power connector
ëËÎÓ‚ÓÈ ‡Á˙ÂÏ
Hex. Nut (5 mm ø)
òÂÒÚË„‡Ì̇fl „‡È͇ (5 mm {ÏÏ} ø)
ø
Trim plate
é·‡ÏÎÂÌËÂ
Rear support strap
ᇉÌflfl ÓÔÓ̇fl Ô·Ì͇
Tapping Screw (5 mm ø x 16 mm)
ë‡ÏÓ̇ÂÁ‡˛˘ËÈ ‚ËÌÚ (5 mm {ÏÏ} ø x 16 mm)
ø x 16mm
FX0214C384ZB ✽
✽
✽
✽
Lock cancel plate
è·ÒÚË̇ ÒÌflÚËfl ÒÚÓÔÓÂÌËfl
YFG044C002ZA
1
2
1
1
1
1
1
YEFC051013
YGAJ021011
e
w
q
Page: 41
CQ-C7405W Installation Instructions YFM294C092CA (2)
L
R
Lead Connections
Connect all wires, making sure that each connection is insulated and
secure. Bundle all loose wires and fasten them with tape so they will not
fall down later. Now insert the unit into the mounting collar.
Congratulations! After making a few final checks, you’re ready to enjoy
your new auto stereo system.
èÓÍ·‰Í‡ ˝ÎÂÍÚÓÔÓ‚Ó‰ÍË
èÓ‰Ú‚Âʉ‡fl ËÁÓÎflˆË˛ Ë Ì‡‰ÂÊÌÓÒÚ¸ ‚ÒÂı ÒÓ‰ËÌÂÌËÈ, ÒÓ‰ËÌfl˛Ú ‚ÒÂ
ÔÓ‚Ó‰˚. é·‚flÁ˚‚‡˛Ú ‚Ò ҂ӷӉÌ˚ ÔÓ‚Ó‰˚ ÎÂÌÚÓÈ ‰Îfl
Ô‰ÓÚ‚‡˘ÂÌËfl Ëı ÓÚÔ‡‰ÂÌËfl. ÇÒÚ‡‚Îfl˛Ú ‡ÔÔ‡‡Ú ‚ ÏÓÌÚ‡ÊÌÛ˛ ‡ÏÛ.
Final Installation/éÍÓ̘‡ÚÂθÌ˚È ÏÓÌÚ‡Ê/ Final Check/éÍÓ̘‡ÚÂθ̇fl ÔÓ‚Â͇/
1. Make sure that all wires are properly connected and insulated.
2. Make sure that the main unit is securely held in the mounting collar.
3. Turn on the ignition to check the unit for proper operation.
If you have difficulties, consult your nearest authorized professional
installer for assistance.
1. ì·Âʉ‡˛ÚÒfl, ˜ÚÓ ‚Ò ÔÓ‚Ó‰˚ Ô‡‚ËθÌÓ ÒÓ‰ËÌÂÌ˚ Ë ËÁÓÎËÓ‚‡Ì˚.
2. ì·Âʉ‡˛ÚÒfl, ˜ÚÓ ‡ÔÔ‡‡Ú ̇‰ÂÊÌÓ Á‡ÙËÍÒËÓ‚‡Ì ̇ ÏÓÌÚ‡ÊÌÓÈ ‡ÏÂ.
3. ÇÍβ˜‡˛Ú ‚˚Íβ˜‡ÚÂθ Á‡ÊË„‡ÌËfl ‰Îfl ÔÓ‚ÂÍË ÌÓχθÌÓÈ ‡·ÓÚ˚
‡ÔÔ‡‡Ú‡.
èË ‚ÓÁÌËÍÌÓ‚ÂÌËË ÔÓ·ÎÂÏ ÒΉÛÂÚ Ó·‡ÚËÚ¸Òfl Í ‡‚ÚÓËÁÓ‚‡ÌÌÓÏÛ
ÔÓÙÂÒÒËÓ̇θÌÓÏÛ ÏÓÌÚ‡ÊÌËÍÛ Á‡ ÔÓÏÓ˘¸˛.
System Upgrade Example: Connecting with a CD changer/èËÏÂ ÔÓ‚˚¯ÂÌËfl ÙÛÌ͈ËË ÒËÒÚÂÏ˚: ëÓ‰ËÌÂÌËÂ Ò CD-˜ÂÈ̉ÂÊÓÏ
Battery Lead
ŇڇÂÈÌ˚È ÔÓ‚Ó‰
DIN Cord
òÌÛ DIN
RCA Cord
òÌÛ RCA
(Option)
(ÔÓ ÓÔˆËË)
(Option)
(ÔÓ ÓÔˆËË)
Ground Lead
á‡ÁÂÏÎfl˛˘ËÈ ÔÓ‚Ó‰
Wiring/åÓÌÚ‡Ê ˝ÎÂÍÚÓÔÓ‚Ó‰ÓÍ/
Connect as follows.
åÓÌÚËÛ˛Ú ÔÓ‚Ó‰ÍË Ú‡Í, Í‡Í ÔÓ͇Á‡ÌÓ Ì‡ ËÒ. ÌËÊÂ.
Speaker Connection/åÓÌÚ‡Ê ˝ÎÂÍÚÓÔÓ‚Ó‰ÓÍ „ÓÏÍÓ„Ó‚ÓËÚÂÎÂÈ/
Caution
To prevent damage to the unit, do not connect the power connector
until the whole wiring is completed.
●Do not use a 3-wire type speaker system
having a common earth lead.
●ç ÒΉÛÂÚ ÔËÏÂÌflÚ¸ ÚÂıÔÓ‚Ó‰ÌÛ˛ „ÓÏÍÓ„Ó‚ÓËÚÂθÌÛ˛ ÒËÒÚÂÏÛ,
Ëϲ˘Û˛ Ó·˘ËÈ Á‡ÁÂÏÎfl˛˘ËÈ ÔÓ‚Ó‰.
●
Caution
●Do not connect more than one speaker to
one set of speaker leads. (except for connecting to
a tweeter)
●Use ungrounded speakers only.
Allowable input : 50 W or more
Impedance : 4 – 8 Ω
●Use of speakers which do not match the specifications can cause
burning, smoking or damage of the speakers.
●Distance between speaker and amplifier: 30 cm or more
●ëΉÛÂÚ ÔËÏÂÌflÚ¸ ÚÓθÍÓ ÌÂÁ‡ÁÂÏÎÂÌÌ˚ „ÓÏÍÓ„Ó‚ÓËÚÂÎË.
ÑÓÔÛÒ͇ÂÏ˚È ‚ıÓ‰: 50 W {ÇÚ} ËÎË ·ÓÎÂÂ
àÏÔ‰‡ÌÒ: éÚ 4 – 8 Ω {éÏ}
●àÒÔÓθÁÓ‚‡ÌË „ÓÏÍÓ„Ó‚ÓËÚÂÎÂÈ Ò ÌÂÔÓ‰ıÓ‰fl˘ËÏË ÚÂıÌ˘ÂÒÍËÏË
ı‡‡ÍÚÂËÒÚË͇ÏË ÏÓÊÂÚ ÔË‚ÂÒÚË Í Ó·„Ó‡Ì˲ , ‚ÓÁÌËÍÌÓ‚ÂÌ˲ ‰˚χ ËÎË
ÔÓ‚ÂʉÂÌ˲ „ÓÏÍÓ„Ó‚ÓËÚÂÎÂÈ.
●ê‡ÒÒÚÓflÌË ÏÂÊ‰Û „ÓÏÍÓ„Ó‚ÓËÚÂÎflÏË Ë ÛÒËÎËÚÂÎÂÏ: 30 cm ËÎË ·ÓÎÂÂ
●
– Ω
●
●
Front Left + (White)
èÂ‰ÌËÈ Î‚˚È + (ÅÂÎ˚È)
Front Left – (White w/black stripe)
èÂ‰ÌËÈ Î‚˚È – (ÅÂÎ˚È ÔÓ‚Ó‰ Ò ˜ÂÌÓÈ ÔÓÎÓÒÍÓÈ)
–
-
+
Rear Right + (Violet)
ᇉÌËÈ Ô‡‚˚È + (îËÓÎÂÚÓ‚˚È)
Rear Right – (Violet w/black stripe)
ᇉÌËÈ Ô‡‚˚È – (îËÓÎÂÚÓ‚˚È ÔÓ‚Ó‰ Ò ˜ÂÌÓÈ ÔÓÎÓÒÍÓÈ)
–
+
-
Front Right + (Gray)
èÂ‰ÌËÈ Ô‡‚˚È + (ëÂ˚È)
Front Right – (Gray w/black stripe)
èÂ‰ÌËÈ Ô‡‚˚È – (ëÂ˚È ÔÓ‚Ó‰ Ò ˜ÂÌÓÈ
ÔÓÎÓÒÍÓÈ)
–
+
-
Rear Left + (Green)
ᇉÌËÈ Î‚˚È + (áÂÎÂÌ˚È)
Rear Left – (Green w/black stripe)
ᇉÌËÈ Î‚˚È – (áÂÎÂÌ˚È ÔÓ‚Ó‰ Ò ˜ÂÌÓÈ ÔÓÎÓÒÍÓÈ)
–
+
-
ëËÎÓ‚ÓÈ ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ (Äëë ËÎË IGN) ä ÔËÚ‡Ì˲ Äëë, +12 V {B} ÔÓÒÚ.Ú.
Antenna
ÄÌÚÂÌ̇
(L)/(ã‚.)/
(R)/(è‡‚.)/
Preamp Out Connector (Rear)
ÉÌÂÁ‰Ó ‰Îfl ÔÓ‰Íβ˜ÂÌËfl ‚˚ıÓ‰ÌÓ„Ó Í‡·ÂÎfl Ô‰ÛÒËÎËÚÂÎfl (Á‡‰ÌÂÂ)
ÇÌËχÌËÂ
ÇÓ ËÁ·ÂʇÌË ÔÓ‚ÂʉÂÌËfl ÔË·Ó‡ Ì ÒΉÛÂÚ ÔÓ‰ÒÓ‰ÂÌËflÚ¸ ÒËÎÓ‚ÓÈ ‡Á˙ÂÏ ‰Ó
ÔÓÎÌÓ„Ó Á‡‚Â¯ÂÌËfl ÏÓÌڇʇ ˝ÎÂÍÚÓÔÓ‚Ó‰ÓÍ.
ÇÌËχÌËÂ
●çÂθÁfl ÔÓ‰ÒÓ‰ËÌflÚ¸ ‰‚‡ Ë ·ÓΠ„ÓÏÍÓ„Ó‚ÓËÚÂÎfl Í Ó‰ÌÓÏÛ
̇·ÓÛ ‚˚‚Ó‰Ì˚ı ÔÓ‚Ó‰Ó‚ „ÓÏÍÓ„Ó‚ÓËÚÂÎfl (Á‡ ËÒÍβ˜ÂÌËÂÏ
ÒÎÛ˜‡fl ÔÓ‰ÒÓ‰ËÌÂÌËfl Í „ÓÏÍÓ„Ó‚ÓËÚÂβ ‰Îfl
‚ÓÒÔÓËÁ‚‰ÂÌËfl ‚ÂıÌËı ˜‡ÒÚÓÚ)
●
(White)/(ÅÂÎ˚È)/
(Red)/(ä‡ÒÌ˚È)/
ACC
BATTERY 15A
FRONT SP
REAR SP
AUX Input Connector
ê‡Á˙ÂÏ AUX-‚ıÓ‰‡
Fuse (15 A) Refer fuse replacement to your nearest authorized Panasonic Service
Center. Do not try fuse replacement by yourself.
è·‚ÍËÈ Ô‰Óı‡ÌËÚÂθ (̇ 15 Ä) ᇠÁ‡ÏÂÌÓÈ Ô·‚ÍÓ„Ó Ô‰Óı‡ÌËÚÂÎfl ÒΉÛÂÚ Ó·‡˘‡Ú¸Òfl Í
·ÎËʇȯÂÏÛ ‡‚ÚÓËÁÓ‚‡ÌÌÓÏÛ ˆÂÌÚÛ ÚÂıÓ·ÒÎÛÊË‚‡ÌËfl «Panasonic». çÂθÁfl Ò‡ÏÓÏÛ Ô˚Ú‡Ú¸Òfl Á‡ÏÂÌËÚ¸
Ô·‚ÍËÈ Ô‰Óı‡ÌËÚÂθ.
Power Lead (ACC or IGN) To ACC power, +12 V DC.
(Red)/(ä‡ÒÌ˚È)/
Ground Lead To a clean, bare metallic part of the car chassis.
(Black)/(óÂÌ˚È)/
á‡ÁÂÏÎfl˛˘ËÈ ÔÓ‚Ó‰ ä ˜ËÒÚÓÈ, ӷ̇ÊÂÌÌÓÈ ÏÂÚ‡Î΢ÂÒÍÓÈ ˜‡ÒÚË ‡‚ÚÓÏÓ·ËθÌÓ„Ó ¯‡ÒÒË.
Battery Lead To the car battery, continuous +12 V DC.
(Yellow)/(ÜÂÎÚ˚È)/
Ç˚‚Ó‰ ·‡Ú‡ÂË ä ‡‚ÚÓÏÓ·ËθÌÓÈ ·‡Ú‡ÂÂ, ÌÂÔÂ˚‚Ì. +12 V {B} ÔÓÒÚ.Ú.
(Blue w/white stripe)/(ëËÌËÈ ÔÓ‚Ó‰ Ò ·ÂÎÓÈ ÔÓÎÓÒÍÓÈ)/
(Orange)/(é‡ÌÊ‚˚È)/
External Amplifier Control Power Lead To an external amplifier. (Max. 100 mA)
ëËÎÓ‚ÓÈ ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ ‰Îfl ÛÔ‡‚ÎÂÌËfl ‚̯ÌËÏ ÛÒËÎËÚÂÎÂÏ ä ‚Ì¯ÌÂÏÛ ÛÒËÎËÚÂβ. (å‡ÍÒ. 100 mA {ÏÄ} )
External Mute Lead
To the Navi Mute Lead of the Panasonic Car Navigation system or car telephone mute lead.
Ç̯ÌËÈ ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ ‰Îfl ÔË„ÎÛ¯ÂÌËfl Á‚Û͇
ä ‚˚‚Ó‰Û Navi Mute ‡‚ÚÓÏÓ·ËθÌÓÈ Ì‡‚Ë„‡ˆËÓÌÌÓÈ ÒËÒÚÂÏ˚ «Panasonic» ËÎË ‚˚‚Ó‰Û ‰Îfl ÔË„ÎÛ¯ÂÌËfl Á‚Û͇ ‰Îfl
‡‚ÚÓÏÓ·ËθÌÓ„Ó ÚÂÎÂÙÓ̇.
Subwoofer Output Connector
The RCA cord of an external power amplifier should be connected.
ëÓ‰ËÌËÚÂθ Í ‚˚ıÓ‰Û Ò‡·‚ÛÙÂ‡
ëÓ‰ËÌfl˛Ú ¯ÌÛ RCA ‚̯ÌÂ„Ó ÛÒËÎËÚÂÎfl.
(Red)/(ä‡ÒÌ˚È)/
(R)/(è‡‚.)/(
(Red)/(ä‡ÒÌ˚È)/
(R)/(è‡‚.)/(
(Red)/(ä‡ÒÌ˚È)/
(R)/(è‡‚.)/(
(Red)/(ä‡ÒÌ˚È)/
(R)/(è‡‚.)/(
(White)/(ÅÂÎ˚È)/
(L)/(ã‚.)/
(White)/(ÅÂÎ˚È)/
(L)/(ã‚.)/
(White)/(ÅÂÎ˚È)/
(L)/(ã‚.)/
(White)/(ÅÂÎ˚È)/
(L)/(ã‚.)/
Preamp Out Connector (Front)
ÉÌÂÁ‰Ó ‰Îfl ÔÓ‰Íβ˜ÂÌËfl ‚˚ıÓ‰ÌÓ„Ó Í‡·ÂÎfl Ô‰ÛÒËÎËÚÂÎfl (ÔÂ‰ÌÂÂ)
CX-DP880
CQ-C7405W
CA-CC30N
CHANGER IN
Conversion Cable for DVD/CD Changer
äÓÌ‚ÂÒËÓÌÌ˚È Í‡·Âθ ‰Îfl DVD/CD-˜ÂÈ̉ÊÂ‡.
PRE-OUT REAR
PRE-OUT FRONT
AUX1-IN
S.W-OUT
System up Connector
ê‡Á˙ÂÏ ‰Îfl ‡Ò¯ËÂÌËfl ÒËÒÚÂÏ˚
System up
Connector
ê‡Á˙ÂÏ ‰Îfl
‡Ò¯ËÂÌËfl ÒËÒÚÂÏ˚
(Blue)/(ëËÌËÈ)/
Motor Antenna Relay Control Lead To Motor Antenna. (Max. 100 mA) (This lead is not intended for use with a
switch actuated power antenna)
Ç˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ ÂÎÂÈÌÓ„Ó ÛÔ‡‚ÎÂÌËfl ‡ÌÚÂÌÌÓÈ Ò ÏÓÚÓÌ˚Ï ÔË‚Ó‰ÓÏ ä ‡ÌÚÂÌÌÂ Ò ÏÓÚÓÌ˚Ï ÔË‚Ó‰ÓÏ.
(å‡ÍÒ. 100 mÄ {ÏÄ})
(ùÚÓÚ ‚˚‚Ó‰ÌÓÈ ÔÓ‚Ó‰ Ì Ô‰̇Á̇˜ÂÌ ‰Îfl ÔËÏÂÌÂÌËfl Ò ‡ÌÚÂÌÌÓÈ Ò ÏÓÚÓÌ˚Ï ÔË‚Ó‰ÓÏ, ‚Íβ˜‡ÂÏÓÈ ÔÂÂÍβ˜‡ÚÂÎÂÏ)
Page: 42
¡ For upgrading your system, read this manual carefully before use. This manual should be retained for future reference after
read.
¡ ÑÎfl ‡Ò¯ËÂÌËfl LJ¯ÂÈ ÒËÒÚÂÏ˚ ÔÓÒËÏ Ú˘‡ÚÂθÌÓ ˜ËÚ‡Ú¸ ‰‡ÌÌÛ˛ ËÌÒÚÛÍˆË˛ ÔÂ‰ ËÒÔÓθÁÓ‚‡ÌËÂÏ ‡ÔÔ‡‡Ú‡. чÌÌÛ˛
ËÌÒÚÛÍˆË˛ ÒΉÛÂÚ ı‡ÌËÚ¸ ‰Îfl ‰‡Î¸ÌÂÈ¯Â„Ó ÔÓθÁÓ‚‡ÌËfl.
System Upgrade Guidebook
àÌÒÚÛ͈Ëfl ÔÓ ‡Ò¯ËÂÌ˲ ÒËÒÚÂÏ˚
Model: CQ-C7405W
Page: 43
2 CQ-C7405W
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or death.
■ Read the operating instructions for the unit and all other com-
ponents of your car audio system carefully before using the
system. They contain instructions about how to use the sys-
tem in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■ This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material dam-
age.
Caution
Warning
Observe the following warnings when using
this unit.
❑The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this prod-
uct with other battery systems, especially a 24 V DC battery
system.
❑Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult
your dealer or an authorized Panasonic Service Center.
❑Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑Refer fuse replacement to qualified service person-
nel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
Observe the following warnings when
installing.
❑Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑Never use safety-related components for installa-
tion, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gaso-
line tank, and electric wiring are located. Then open the hole
from outside if possible.
❑Never install the product in a location where it inter-
feres with your field of vision.
❑Never have the power cord branched to supply other
equipment with power.
❑After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑In the case of installation to an airbag equipped car,
confirm warnings and cautions of the vehicle manu-
facturer before installation.
❑Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑Insulate all exposed wires to prevent short circuit-
ing.
Safety Information
Page: 44
3
English
CQ-C7405W
Safety
Information
Caution
Observe the following cautions when using this
unit.
❑Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
❑This unit is designed for use exclusively in automo-
biles.
❑Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑Do not expose the unit to direct sunlight or exces-
sive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on rainy
days.
Observe the following cautions when
installing.
❑Refer wiring and installation to qualified service
personnel.
Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.
❑Follow the instructions to install and wire the prod-
uct.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws, and
moving parts such as seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.
❑Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those sup-
plied or designated may result in internal damage to the unit.
Faulty installation may lead to an accident, a malfunction or
fire.
❑Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑Installation Angle
The product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit can be installed.
Consult your dealer for further details.
❑Wear gloves for safety. Make sure that wiring is
completed before installation.
❑To prevent damage to the unit, do not connect the
power connector until the whole wiring is complet-
ed.
❑Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling
the battery for the remote control unit.
●Use only specified battery (CR2025).
●Match the polarity of the battery with the (+) and (–) marks
in the battery case.
●Replace dead battery as soon as possible.
●Remove the battery from the remote control unit when not
using it for an extended period of time.
●Insulate the battery (by placing them in a plastic bag or cov-
ering them with vinyl tape) before disposal or storage.
●Dispose of the battery according to the local regulations.
●Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
In case of battery leakage
●Thoroughly wipe the battery liquid off the battery case and
insert new battery.
●If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.
●If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical atten-
tion.
Refer to safety information of optional devices as well.
Page: 45
4 CQ-C7405W
Before Reading These Instructions
About
this
Book
This book is an instruction manual that explains how to
operate your purchased head unit and its remote control
as an accessory when the head unit is connected to
optional devices.
(Remote Control Unit a Operating Instructions)
System
Upgrade
Sample
Expansion Module (hub unit):
CY-EM100N (Option) (a Page 6)
Hands-Free Phone System:
CY-BT100N (Option)
(a Page 14)
DVD Changer
CX-DH801W
(Option) (a Page 8)
Head Unit: CQ-C7405W
Monitor: CY-VM1500EX (Option)
iPod
(a Page 12)
Expansion Module
(CY-EM100N, option)
CD Changer
(CX-DP880, option)
Conversion Cable for DVD/CD
Changer
(CA-CC30N, option)
System-up Connector
Direct Cable for iPod
(CA-DC300N, option)
Hands-Free Kit featuring
Bluetooth®
technology
(CY-BT100N, option)
iPod
Cellular Phone
Only 1 unit
Up to
4 units
CY-BT100U
CY-BT100U
Notes:
¡ Refer to individual instruction and instal-
lation manuals for each device for detailed
installation and wiring.
¡ A hub unit is not required to connect only
one optional component.
Head Unit
CQ-C7405W
Page: 46
5
CQ-C7405W
Contents
¡Safety Information 2
¡Before Reading These Instructions 4
¡General 6
¡Disc Changer 8
¡iPod Control 12
¡Hands-Free Phone System 14
English 2
Each
Source
¡Troubleshooting 16
As
Needed
ê
êÛ
ÛÒ
ÒÒ
ÒÍ
ÍË
ËÈ
È 18
34
Common
Page: 47
6 CQ-C7405W
Connectable
Devices
General
DVD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the optional
Panasonic DVD changer unit (CX-DH801W). For details,
refer to the operating instructions for the DVD changer
unit. (a page 8, 10)
CD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the optional
Panasonic CD changer unit (CX-DP880). For details, refer
to the operating instructions for the CD changer unit.
(a page 8)
iPod®
The optional adapter (Direct Cable for iPod: CA-
DC300N) allows you to connect the optional iPod series.
(a page 12)
The iPod equipped with a dock connector is exclusively
connectable. Further information about the controllable
iPod is described below.
Controllable iPod/software version
¡ 3rd generation iPod/ver. 2.3
¡ 4th generation iPod/ver. 3.1.1
¡ 5th generation iPod/ver. 1.1.2 (Video playback is not
supported.)
¡ iPod Photo/ver. 1.2.1
¡ iPod mini/ver. 1.4.1
¡ iPod nano/ver. 1.2
* Operation check has been completed with software
available at the end of October, 2006. We do not guaran-
tee the operation with our future products or upgraded
software.
iPod is a trademark of Apple Computer, Inc., registered in
the U.S. and other countries.
Hands-Free Phone System
You can connect the optional Hands-Free Phone System
(Hands-Free Kit featuring Bluetooth®
technology:
CY-BT100N). For details, refer to the operating
instructions for the Hands-Free Phone System.
(a page 14)
Note: This unit is designed only for receiving calls.
It cannot send calls.
Bluetooth®
The Bluetooth word mark and logo are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Matsushita Electric Industrial Co.,Ltd. is under
license. Other trademarks and trade name are those
of their respective owners.
Expansion Module (hub unit)
You can connect the optional Expansion Module (hub
unit) (CY-EM100N). Connection of the Expansion Module
allows you to simultaneously connect optional devices
mentioned before as well as other AV devices. For
details, refer to the operating instructions for the
Expansion Module.
Connectable devices
¡ CD changer (max. 1)
¡ iPod (max. 2)
¡ Hands-Free Phone System (max. 1)
Note: Market conditions regarding optional devices vary
with countries and regions. For further information,
consult your dealer.
Page: 48
7
English
CQ-C7405W
General
Radio
FM1, FM2, FM3, AM (a Operating Instructions)
Source
Selection
(SOURCE)
The source changes as follows every time
[SOURCE] is pressed.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Player
When loading CD (a Operating Instructions)
When loading a disc containing compressed
audio files (a Operating Instructions)
AUX 1
Device connected to the AUX terminal of the this unit
System-up Connector
Device connected to the System-up Connector of this
unit
When optional devices are connected:
Shift to connected devices
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated
in sequence after shifting to AUX2 (devices connected
to the AUX terminal of the expansion module).
When connecting DVD Changer (a page 8, 10)
When connecting CD Changer (a page 8)
When connecting iPod (a page 12)
When connecting Expansion Module
Page: 49
8 CQ-C7405W
Disc Changer(When CDs or MP3 discs are loaded)
Connected an optional CD changer or an optional DVD changer can be controlled by this unit.
1 Load a magazine (discs).
When a magazine is already loaded, press
[SOURCE] to select the CD changer mode.
The unit recognizes the magazine and starts playing
automatically.
2 Select a desired portion.
Disc selection
[}] (DISC): Next disc
[{] (DISC): Preceding disc
Folder up/Down
Only for DVD Changer
Hold down for 2 sec. or more.
[}] (FOLDER): Next folder
[{] (FOLDER): Preceding folder
Track/File selection
[7]: Next track/file
[6]: Preceding track/file (press twice)
Note: Hold down for fast forward/reverse.
Pause
Press [BAND] (y / 5).
Press again to cancel.
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M
Disc number
Time
lights when the changer is
connected.
Play Mode indicators
lights when each mode is
activated.
(CD changer)
Changer indicator
Operation
Flow
CD
Changer
Mode
Display
(DVD changer)
(Disc Random, Only for CD changer)
(Disc Repeat)
(Disc Scan, Only for CD changer)
Track/file
(Folder Repeat, Only for MP3 files)
Page: 50
9
English
CQ-C7405W
Disc
Changer
(When
CDs
or
MP3
discs
are
loaded)
Notes:
¡ When CX-DP880 or CX-DH801W is connected, a CD-RW
disc is playable.
¡ Trouble may occur while playing CD-Rs. Refer to the section
on “Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)”.
(a Operating Instructions)
¡ This unit does not support the following through the CD
changer.
¡MP3 playback.
Random and Repeat play can be set.
1 Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Turn [VOL] to select a function to be
adjusted.
For using the remote
control, use [}] or
[{].
3 Press [PUSH
SEL] to adjust.
For using the remote control, use [BAND] (SET).
4 Press [MENU] to close the menu
screen.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
RANDOM
¡ CD-DA
RANDOM playback of the selected disc (DVD changer)
RANDOM playback of all discs in the magazine (CD
changer)
¡ MP3 disc
RANDOM playback of the selected folders
: Off (default)
: Random playback
DISC RANDOM (Only for CD changer)
: Off (default)
: Random playback (from selected disc)
REPEAT
: Off (default)
: Playing the current track/file repeatedly
DISC REPEAT (Only for CD-DA disc)
: Off (default)
: Playing the current disc repeatedly
FOLDER REPEAT (Only for MP3 disc)
: Off (default)
: Playing the current folder repeatedly
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Play Mode Selection
One-touch operation is available for selecting a track
playing style by use of [RANDOM] or [REPEAT].
RANDOM, REPEAT
Press the button. Press again to cancel.
DISC RANDOM, DISC REPEAT, FOLDER REPEAT
Hold down the button for 2 sec. or more.
Hold down again to cancel.
SCAN play
You can find your favorite file by playing first 10-sec. of
each file.
SCAN (CD changer: All tracks, DVD changer:
from selected disc)
Press [SCAN]. Press again to cancel.
DISC SCAN (1st file in each disc, only for CD
changer)
Hold down [SCAN] for 2 sec. or more. Hold down
again to cancel.
Direct Access
A disc can be directly selected.
Example: disc number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [SET].
Note: To suspend direct
selection, press [DISP] (DISPLAY).
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
VOLPUSH SEL/ SRSWOW
D
・
M
Functions
Only
by
Remote
Control
Unit
Random,
Repeat
Play
(Disc
Changer
Menu
Display)
(RANDOM,
REPEAT)
Page: 51
10 CQ-C7405W
Disc Changer (when DVDs or VCDs are loaded)
Connected an optional DVD changer (CX-DH801W) can be controlled by this unit.
1 Load a magazine (discs).
When a magazine is already loaded, press
[SOURCE] to select the DVD changer mode.
The unit recognizes the magazine and starts playing
automatically.
Notes:
¡ For DVD operations other than the above (i.e. DVD
menu, closed caption, etc.), use the remote con-
trol unit supplied with the DVD changer.
¡ The remote control unit supplied with the DVD
changer does not work properly when you aim it
at this unit.
¡ When using the remote control unit supplied with
the DVD changer, aim it at the monitor display
(CY-VM1500EX).
2 Select a desired portion.
Disc selection
[}] (DISC): Next disc
[{] (DISC): Preceding disc
Chapter/Track selection
[7]: Next chapter/Next track
[6]: Preceding chapter/ Preceding track
(press twice)
Note: Hold down for fast forward/reverse.
Pause
Press [BAND] (y / 5).
Press again to cancel.
Disc number
Time
lights when the changer is
connected.
Play Mode indicators
lights when each mode is
activated.
Chapter number
Changer indicator
(Disc Repeat)
(Chapter Repeat)
(Title Repeat)
Operation
Flow
DVD
Changer
Mode
Display
Disc type
OPEN
DISP
BAND
CQ-C7405W
TILT
/SET/APM
SQ
MENU
TUNE
TRACK
MUTE
SBC-SW
FOLDER/P-SET/DISC
LIST
SOURCE PWR
/
VOLPUSH SEL/ SRSWOW
D
・
M

Question & answers

There are no questions about the Panasonic CQ-C7405W yet.

Ask a question about the Panasonic CQ-C7405W

Have a question about the Panasonic CQ-C7405W but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Panasonic CQ-C7405W. Please make sure that you describe your difficulty with the Panasonic CQ-C7405W as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.