Tough TG-2

Olympus Tough TG-2 manual

Tough TG-2

User manual for the Olympus Tough TG-2 in English. This PDF manual has 107 pages.

Page: 1
DIGITAL CAMERA Instruction Manual TG-2 ● Thank you for purchasing an Olympus digital camera. Before you start to use your new camera, please read these instructions carefully to enjoy optimum performance and a longer service life. Keep this manual in a safe place for future reference. ● We recommend that you take test shots to get accustomed to your camera before taking important photographs. ● In the interest of continually improving products, Olympus reserves the right to update or modify information contained in this manual.
Page: 2
2 EN Checking the contents of the box or Digital camera Strap Lithium Ion Battery (LI-90B) USB-AC adapter (F-2AC) USB cable (CB-USB8) OLYMPUS Setup CD-ROM Lens ring Names of Parts Names of Parts 1 2 3 5 4 6 7 8 10 9 12 13 11 14 3 1 Connector cover 2 Connector cover lock 3 LOCK knob 4 Speaker 5 Multi-connector 6 HDMI micro connector 7 Strap eyelet 8 Self-timer lamp/LED Illuminator/ AF illuminator 9 Flash 10 Lens 11 Lens ring 12 Tripod socket 13 Battery/card cover 14 Battery/card cover lock Other accessories not shown: Warranty card Contents may vary depending on purchase location.
Page: 3
3 EN 1 2 5 6 3 7 8 9 4 13 12 10 11 1 Stereo microphone 2 GPS antenna 3 Monitor 4 Shutter button 5 Indicator lamp 6 n button 7 Zoom buttons 8 R button (shooting movies) 9 Mode dial 10 q button (switching between shooting and playback) 11 Arrow pad INFO (changing information display) # (flash) Y (self-timer)  (erase) 12 A button (OK) 13  button Attaching the camera strap Attaching the camera strap 1 2 3 Pull the strap tight so that it does not come loose. Arrow pad H (left) G (down) F (up) I (right) A FGHI instruct to press the up/down/left/right arrow pad.
Page: 4
4 EN Inserting and removing the battery and card (commercially available) 1 Follow Steps 1, 2 and 3 to open the battery/card cover. 3 1 2 Battery/card cover Battery/card cover lock LOCK knob Turn off the camera before opening the battery/ card cover. 2 Insert the battery while sliding the battery lock knob in the direction of the arrow. Battery lock knob Insert the battery as illustrated with the C mark toward the battery lock knob. Damage to the battery exterior (scratches, etc.) may produce heat or an explosion. Slide the battery lock knob in the direction of the arrow to unlock, and then remove the battery. 3 Insert the card straight until it clicks into place. Write-protect switch Always use SD/SDHC/SDXC/Eye-Fi/FlashAir (with Wireless LAN function) card with this camera. Do not insert other types of memory cards. “Using the card” (p. 79) ● Do not touch the metallic parts of the card directly. To remove the card To remove the card 2 1 Press the card in until it clicks and comes out slightly, then remove the card.
Page: 5
5 EN 4 Follow Steps 1, 2 and 3 to close the battery/card cover. 3 2 1 1 When using the camera, be sure to close and lock the battery/card cover. Charging the battery Connect the USB cable and USB-AC adapter to the camera and charge the battery. For charging the battery abroad, see “Using your charger and USB-AC adapter abroad” (p. 79). ● The battery is not fully charged at shipment. Before use, be sure to charge the battery until the indicator lamp turns off (up to 4 hours). Connecting the camera Connecting the camera 1 2 AC outlet USB cable (supplied) Connector cover Multi-connector LOCK knob Connector cover lock Indicator lamp On: Charging Off: Charged
Page: 6
6 EN When to charge the batteries When to charge the batteries Charge the battery when the error message shown below appears. Battery Empty Error message Flashes in red Never use any cable other than supplied or Olympus-designated USB cable. This may cause smoking or burning. The included F-2AC USB-AC adapter (hereafter referred to as USB-AC adapter) differs depending on the region where you purchased the camera. If you received a plug-in type USB- AC adapter, plug it directly into AC outlet. The included USB-AC adapter has been designed to be used for charging and playback. Do not take pictures while the USB-AC adapter is connected to the camera. Be sure to unplug the power plug of the USB-AC adapter from the wall outlet when the charging is complete or the playback ends. For details on the battery, see “Battery Handling Precautions” (p. 98). For details on the USB-AC adapter, see “USB-AC adapter” (p. 99). ● If the indicator lamp does not light, check the USB cable and USB-AC adapter connections. ● The battery can be charged while the camera is connected to the computer via USB. The charging time varies depending on the performance of the computer. (There may be cases in which it takes approx. 10 hours.)
Page: 7
7 EN Turning on the camera and making the initial settings When you turn on the camera for the first time, a screen appears enabling to set the language for the menus and messages displayed in the monitor, and the date and time. To change the selected date and time, see “Setting the date and time d [X]” (p. 49). 1 Press the n button to turn on the camera, press FGHI of the arrow pad to select your language and press the A button. 2 Press FG of the arrow pad to select the year for [Y]. X MENU Back Y/M/D Y M D Time -- -- -- -- : . . 2013 Date and time setting screen 3 Press I of the arrow pad to save the setting for [Y]. X MENU Back Y/M/D Y M D Time -- -- -- -- : . . 2013 4 As in Steps 2 and 3, press FGHI of the arrow pad to set [M] (month), [D] (day), [Time] (hours and minutes), and [Y/M/D] (date order), and then press the A button. For precise time setting, press the A button as the time signal strikes 00 seconds. 5 Press HI of the arrow pad to select time zone and then press the A button. ● Use FG to turn daylight saving time ([Summer]) on or off. MENU ’13.02.26 12:30 Back Summer Seoul Tokyo
Page: 8
8 EN Before Using GPS The camera’s GPS (Global Positioning System) feature determines your position (latitude and longitude) and stores this information with pictures taken with the camera. The camera uses supplementary orbital data (assisted GPS or A-GPS) for improved signal acquisition. A-GPS data must be updated every 14 days. Before using GPS, you will need to set the camera clock to the correct date and time. (p. 49) Updating A-GPS Data Updating A-GPS Data 1 Install the update software (OLYMPUS A-GPS Utility). ● Download the update software from the following website and install it on your computer. http://sdl.olympus-imaging.com/agps/ The update software can also be installed from the supplied PC software. 2 Connect the camera to the computer and launch the update software. “Connecting with a computer” (p. 56) ● Once the software has started, follow the on-screen instructions. Using GPS Using GPS 1 Select [On] for [GPS Settings] > [GPS] in the d (Settings Menu 3) tab. (p. 55) ● Once the camera has determined the position,  and location coordinates will appear in the display. P P 0:34 0:34 4 4 NORM GPS 12M 0.0 0.0 AUTO WB AUTO WB AUTO ISO AUTO ISO 4:3  Blink: Searching GPS signal  Light: Receiving GPS signal ● The camera may take a few minutes to determine position after a period of disuse. If the icon is still flashing after several minutes, the camera is probably having difficulty detecting a signal. Move to an unobstructed outdoor area or otherwise change your location.
Page: 9
9 EN 2 Press INFO button in the shooting display. ● The displays change in the order of Normal → Detailed → No info. → Measurement position information each time F (INFO) is pressed. ● Nearby landmarks in the GPS database will be displayed. OK --------- Updated 1 min ago 2013/02/26 12:30 Latitude/Longitude N123°56' 78'' E123°56' 78'' Barometer 877hpa Altitude/Water Depth 1200m LOG MENU Back Update GPS 4 3 2 1 0 9 8 7 6 5 1 Landmark name 2 Landmark information position 3 Electronic compass 4 Update status 5 GPS tracking active 6 Latitude 7 Longitude 8 Atmospheric/ Hydraulic pressure 9 Altitude/Water depth 0 Current date and time HI Select a landmark. A Update GPS data. ● Some countries or regions may regulate the use of GPS devices. Follow all local regulations. ● Turn GPS off when on board aircraft and in other locations in which the use of GPS devices is prohibited. ● The provision of A-GPS data may be terminated without prior notice. ● Position data may be unavailable or contain errors in the following locations: ● Locations without a clear view of the sky (indoors, underground or underwater, or near trees or tall buildings) ● Locations subject to strong magnetic or radio interference (near high-voltage power lines, magnets, electronic devices, or cell phones operating in the 1.5 GHz band) ● GPS data may take more time acquire or be unavailable in some locations or at certain times of day. ● Do not cover the GPS antenna with your hands or metal objects. ● If the battery is low, the camera cannot acquire GPS data while the camera turns off. ● The camera is not equipped for GPS navigation. ● While [Track] is [On], the GPS receiver will continue to draw power from the battery when the camera is off. ● GPS data are not recorded with movies. ● Press the INFO button while the camera is turned off. The current time and the shooting location are displayed for approx. 30 seconds.
Page: 10
10 EN Learning how to use the camera ● Press the n button to turn on the camera and enter the standby mode. (Press the n button again to turn off the camera.) ● Select the shooting mode, and press the shutter button to shoot a still image. ● To shoot a movie, press the R button. ● Set the shooting functions using the function menu or the setup menu. ● To view images, press the q button to switch to playback mode. ● To return to standby mode, press the q button again, or press the shutter button halfway down and then release it. ● Press and hold the q button while the camera is turned off to start up the camera in the playback mode. ● In this case, pressing the q button again sets the camera to the standby mode. Shooting still images 1 Press the n button to turn on the camera. 2 Select the shooting mode. (p. 14) 3 Hold the camera and compose the shot. When holding the camera, take care not to cover the flash, microphone or other important parts with your fingers, etc. Take care so that the flash window is not exposed to fingerprints or dirt. Press and hold A button to brighten the monitor when there is difficulty in seeing the monitor. The monitor brightness returns to the default setting if no operations are performed for 10 seconds.
Page: 11
11 EN 4 Press the shutter button halfway down to focus. Press halfway P P F2.0 F2.0 1/400 1/400 AF target mark Shutter speed Aperture value ● The camera was unable to focus if the AF target mark flashes red. Try focusing again. 5 To take the picture, gently press the shutter button all the way down while being careful not to shake the camera. Press halfway Press fully Using the zoom Pressing the zoom buttons adjusts the shooting range. W side T side Image size Zoom bar 12M Super-resolution zoom*1 Optical zoom Other *2 *1 For Super-resolution zoom, see [Super-Res Zoom] (p. 36). *2 Due to increased processing of the pixel counts, the image quality will not degrade. The magnification ratio changes depending on the image size setting.
Page: 12
12 EN Using the flash The flash functions can be selected to best match the shooting conditions. 1 Press I. MENU MENU Flash Auto 0.0 0.0 12M AUTO WB AUTO WB AUTO ISO AUTO ISO 4:3 2 Use HI to select the setting option, and press the A button to set. Option Description Flash Auto The flash fires automatically in low-light or backlight conditions. Redeye Pre-flashes are emitted to reduce the occurrence of red eye in your photos. Fill In The flash fires regardless of the available light. Flash Off The flash does not fire. LED On The LED turns on when a picture is taken. This is effective for taking close up pictures. Remote Control For details, see “Taking pictures with the Olympus Wireless RC Flash System” (p. 82). Slave Using the self-timer After the shutter button is pressed all the way down, the picture is taken after a short delay. 1 Press G. 12 12 0.0 0.0 AUTO WB AUTO WB AUTO ISO AUTO ISO MENU MENU 12M 2 2 Y Off 4:3 2 Use HI to select the setting option, and press the A button to set. Option Description Y Off The self-timer is deactivated. Y 12 sec The self-timer lamp turns on for approx. 10 seconds, then blinks for approx. 2 seconds, and then the picture is taken. Y 2 sec The self-timer lamp blinks for approx. 2 seconds, then the picture is taken.  Auto Release*1 When your pet (cat or dog) turns its head towards the camera, its face is recognized and the picture is taken automatically. *1 [Auto Release] is displayed only when the  mode is [U] or [t]. To cancel the self-timer after it starts To cancel the self-timer after it starts Press the  button.
Page: 13
13 EN Shooting screen displays F2.0 F2.0 1/100 1/100 0:34 0:34 DATE 4 4 NORM GPS 877hPa 877hPa 1200m 1200m P P z z 0.0 0.0 AUTO WB AUTO WB AUTO ISO AUTO ISO 12M 4:3 2 1 3 4 5 6 7 8 9 10 11 12 13 20 22 23 24 21 14 18 19 16 17 25 26 27 28 30 31 32 33 15 29 When the shutter button is pressed halfway down Reading a histogram Reading a histogram If the peak fills too much of the frame, the image will appear mostly white. If the peak fills too much of the frame, the image will appear mostly black. The green section shows luminance distribution within the screen’s center. Switching the displays Switching the displays The displays change in the order of Normal → Detailed → No info. → Measurement position information each time F (INFO) is pressed. No. Name Normal Detailed No info. 1 Shooting mode R R – 2 Landmark R R – 3 Flash R R – 4 Self-timer R R R 5 Exposure compensation R R – 6 White balance R R – 7 ISO sensitivity R R – 8 Drive R R – 9 Image size (still images) R R – 10 Aspect R R – 11 Metering – R – 12 World time – R – 13 Recording with sound/ wind noise reduction R R – 14 Image size (movies) R R – 15 Movie recording length R R – 16 Movie recording icon R R – 17 Image stabilization – R – 18 GPS icon R R – 19 Direction information R R – 20 Conversion Lens R R – 21 Date stamp R R – 22 Compression R R – 23 Number of storable still pictures R R – 24 Current memory R R – 25 Battery check R R – 26 Histogram – R – 27 Atmospheric/ Hydraulic pressure – R – 28 Altitude/Water depth – R – 29 Grid Guide – R – 30 AF target mark R R R 31 Aperture value R R R 32 Shutter speed R R R 33 Camera shake warning R R R
Page: 14
14 EN Selecting the shooting mode The default settings of the function are highlighted in . Shooting mode Submode P (P mode) – M (M mode) – a (Super Macro mode) Filter Effect Off/ 1Pop Art/2Pin Hole/3Fish Eye/4Soft Focus/5Punk/ 6Sparkle/7Watercolor/8Reflection/9Miniature/0Fragmented/aDramatic  ( mode) BPortrait/VBeauty/FLandscape/i Hand-Held Starlight/ GNight Scene/MNight+Portrait/CSport/NIndoor/RSelf Portrait/ SSunset/XFireworks/VCuisine/dDocuments/qBeach & Snow/ MSnapshot/kWide1/lWide2/HMacro/UPet Mode - Cat/ tPet Mode - Dog/aSnow/~ Panorama/h Backlight HDR A (A mode) – P (P mode) Pop Art/Pin Hole/Fish Eye/Soft Focus/Punk/Sparkle/Watercolor/Reflection/ Miniature/Fragmented/Dramatic C1, C2 (Custom mode) – ● “List of settings available in each shooting mode” (p. 73), “List of  settings” (p. 74), “List of P settings” (p. 77) ● In certain shooting modes, the camera may take a few moments for image processing after taking a picture.
Page: 15
15 EN 1 Use the mode dial to select the shooting mode. In  or P, press H of the arrow pad for the function menu, then press HI of the arrow pad for the sub menu, and press the A button. NORM 4 4 0:34 0:34 12M 12 4:3 To select a submode To select a submode MENU MENU 12M Portrait 4:3 NORM 4 4 0:34 0:34 12M 12 4:3 Icon indicating the submode that is set Learning about the shooting modes P (P mode) The camera will select the appropriate aperture value and shutter speed for the subject. Changes can also be made to various shooting settings, such as exposure compensation, as needed. M (M mode) The camera will automatically select the optimal shooting mode for the scene. The shooting condition is decided by the camera and settings cannot be changed, excepting some functions. a (Super Macro mode) Images can be taken from up to 1cm away from the subject. ● You can press the A button to fix the focus distance (AF lock). Press the A button again to cancel the AF lock.
Page: 16
16 EN  ( mode) You can shoot with the best mode for the subject and shooting scene. The best shooting settings for various scenes are pre-programmed as submodes. Note that functions may be limited in some modes. Refer to the descriptions displayed on the submode selection screen, and select the desired submode. To take photos with the To take photos with the V V (Beauty) setting (Beauty) setting 1 Select [V Beauty]. 2 Press G to go to the submenu. 3M Recommended MENU MENU 4:3 3 Use HI to select the retouching setting, and press the Q button to set. Retouching setting NORM 4 4 3M 4:3 0:34 0:34 4 Point the camera toward the subject. Check the frame appearing around the face detected by the camera, and then press the shutter button to take the picture. 5 To save the image, select [OK] on the review screen and press the Q button. To retouch the image additionally, select [Beauty Fix]. OK Beauty Fix MENU Back Beauty Fix Beauty Fix 1 Use FGHI to select a retouching item, and press the Q button. MENU Off Eye Color Back 2 Check the retouched effects on the review screen, then press the Q button to start the retouch process and save. ● Settings for Beauty Fix can be registered. ● Depending on the picture, the editing may not be effective.
Page: 17
17 EN To take underwater photos To take underwater photos The [M Snapshot], [k Wide1], [l Wide2]*1 , [H Macro] submode is recommended for shooting underwater. *1 When set to [l Wide2], the focus distance is automatically fixed to approx. 5.0 m (16.4 ft.). To lock the focus distance for underwater To lock the focus distance for underwater shoots (AF lock) shoots (AF lock) In the [M Snapshot], [k Wide1], or, [H Macro] submode, you can press the A button to fix the focus distance (AF lock). Press the A button again to cancel the AF lock. AF lock mark AFLOCK AFLOCK 4 4 NORM 0:34 0:34 0.0 0.0 12M 4:3 To take panoramic photos ([ To take panoramic photos ([~ ~ Panorama]) Panorama]) 1 Select [p Panorama]. 2 Press G to go to the submenu. 3 Use HI to select [Auto], [Manual] or [PC], and press the A button to set. Submenu Application Auto Panorama images are automatically combined just by swinging the camera in the shooting direction. Manual Three frames are taken and combined by the camera. The user composes the shots using the guide frame and manually releases the shutter. PC The frames that were taken are combined into a panorama image using the PC software. ● Move the camera as if rotating it around a vertical axis through the center of the lens to take better panorama images.
Page: 18
18 EN Taking pictures with [Auto] Taking pictures with [Auto] 1 Press the shutter button to take the first frame. 2 Move the camera slightly in the direction of the second frame. Target mark Pointer Screen when combining images from left to right AUTO AUTO MENU OK Cancel Save 3 Move the camera slowly so that the pointer and the target mark overlap. The camera releases the shutter automatically when the pointer and the target overlap. ● To combine only two frames, press the A button. 4 Repeat step 3 to take a third frame. The camera automatically combines the frames into a single panorama image. ● To cancel the panorama function, press the  button. ● If the shutter does not automatically release, try [Manual] or [PC]. Taking pictures with [Manual] Taking pictures with [Manual] 1 Use FGHI to specify at which edge the next picture is to be connected. Direction for combining frames MANUAL MANUAL 2 Press the shutter button to take the first frame. 3 Compose the next shot so that the edge of the first frame displayed faintly on the screen overlaps the subject of the second frame, and press the shutter button. ● To combine only two frames, press the A button. 4 Repeat step 3 to take a third frame. The camera automatically combines the frames into a single panorama image.
Page: 19
19 EN Taking pictures with [PC] Taking pictures with [PC] 1 Use FGHI to select the direction that the frames are combined. 2 Press the shutter button to take the first frame. The edge of the first frame is displayed faintly on the screen. 3 Compose the next shot so that the edge of the first frame displayed faintly on the screen overlaps the subject of the second frame, and press the shutter button. 4 Repeat step 3 until the desired number of frames are taken, and then press the A button or  button when finished. Panorama shooting is possible for up to 10 frames. The shot images are combined into a single panorama image by the PC software. ● For details on installing the PC software, refer to (p. 56). In addition, refer to the PC software help guide for details on how to make panorama images. A (A mode) When an aperture value is set, the camera automatically sets an appropriate shutter speed. After pressing H, you can change the aperture value using FG. P (P mode) You can shoot with special effects. Refer to the sample images displayed on the submode selection screen, and select the desired submode. The best shooting settings for each effect are pre-programmed, so some function settings cannot be changed. ● Note that some effects may not be applied to movies. C1, C2 (Custom mode) In C1 and C2 mode, you can call up shooting settings that you have stored in advance.
Page: 20
20 EN Viewing images 1 Press the q button. Number of frames/ Total number of images 12:30 ’13/02/26 ’13/02/26 12:30 4/30 4/30 Playback image ● Pictures taken using V mode or sequential shooting function are displayed as a group. Press the T button to play back the image in the group. 2 Use HI to select an image. Displays previous image Displays next image ● Hold I to fast forward and hold H to reverse. ● Press the q button again to return to the shooting screen. To play sound recordings To play sound recordings To play sound recorded with an image, select the image and press the A button. ● Press FG to adjust volume. Index view and close-up view Index view enables quick selection of a desired image. Close-up view (up to 10× magnification) allows checking of image details. 1 Press the zoom buttons. Single-image view Close-up view Index view Location*1 (region) Location*1 (world map) 12:30 ’13/02/26 ’13/02/26 12:30 4/30 4/30 12:30 ’13/02/26 ’13/02/26 12:30 4/30 4/30 W T W T W T W T ’13/02/26 ’13/02/26 12:30 MENU Back Location MENU Back Location *1 Location information will be displayed if present.
Page: 21
21 EN To select an image in index view To select an image in index view Use FGHI to select an image, and press the A button to display the selected image in single-image view. To scroll an image in close-up view To scroll an image in close-up view Use FGHI to move the viewing area. Playing back panorama images Panorama images that were combined together using [Auto] or [Manual] can be scrolled for viewing. 1 Select a panorama image during playback. 4/30 4/30 OK Replay ’13/02/26 12:30 2 Press the A button. Viewing area To control panorama image playback To control panorama image playback Stop playback: Press the  button. Pause: Press the A button. Control while paused Press FGHI to scroll the image in the direction of the pressed button. Press the zoom buttons to enlarge/shrink the image. Press the A button to restart scrolling. Playing back grouped images With V or Sequential, the taken images are displayed as a group during playback. T side Expands. • Select the image and press the A button to display the images respectively. • Use HI to view the previous/ next frame. A button Playback/pauses playback.
Page: 22
22 EN Playback mode display ● Normal No. Name Normal Detailed No info. 1 Battery check – R – 2 Eye-Fi transfer data R R – 3 Protect R R – 4 Adding sound R R – 5 Upload order R R – 6 Print reservation/ number of prints R R – 7 Landmark – R – 8 Current memory R R – 9 Frame number/ total number of images R R – 10 Direction information – R – 11 Compression – R – 12 Shutter speed – R – 13 Shooting mode – R – 14 Atmospheric/ Hydraulic pressure – R – 15 ISO sensitivity – R – 16 Aperture value – R – 17 Altitude/Water depth – R – 18 Histogram – R – 19 Exposure compensation – R – 20 Shooting submode – R – 21 White balance – R – 22 Image size – R – 23 File name – R – 24 Recording date and time R R – 25 Grouped images R R R 12:30 ’13/02/26 ’13/02/26 12:30 10 10 4/30 4/30 9 8 24 25 2 3 6 4 5 Still image ● Detailed 100-0004 4/30 4/30 2.0 1/1000 3968 2976 AUTO WB 100 ISO NORM 1 MAGIC ’13/02/26 12:30 F3.9 10 10 877hpa 1200m ’13/02/26 12:30 100-0004 2.0 1/1000 3968 2976 AUTO WB 100 ISO NORM 1 MAGIC F3.9 877hpa 1200m 9 10 8 14 13 15 12 11 16 17 18 24 25 23 1 2 3 5 4 22 21 20 6 7 19 ● No information 25 Switching the displays Switching the displays The displays change in the order of Normal → Detailed → No info. each time F (INFO) is pressed.
Page: 23
23 EN Erasing images during playback 1 Display the image you want to erase and press G (). MENU Erase Erase Cancel 4/30 4/30 100-0004 100-0004 Back 2 Press FG to select [Erase], and press the A button. ● Grouped images are erased as a group. If you want to delete images from the grouped images, you can expand the group and delete the images individually. ● Multiple images or all images can be erased at a time (p. 41). Shooting movies 1 Press the R button to start recording. 0:00 REC REC 0:00 0:00 0:00 REC REC 0:34 0:34 0:34 0:34 Lights up red when recording Recording time Recording length (p. 81) ● The movie is shot in the set shooting mode. Note that the shooting mode effects may not be obtained for some shooting modes. ● Sound is also recorded. ● When using a camera with a CMOS image sensor, moving objects may appear distorted due to the rolling shutter phenomenon. This is a physical phenomenon whereby distortion occurs in the filmed image when shooting a fast-moving subject or due to camera shaking. In particular, this phenomenon becomes more noticeable when using a long focal length. 2 Press the R button again to stop recording.
Page: 24
24 EN Playing back movies Select a movie, and press the A button. 00:12/00:34 00:12/00:34 During playback Movie ’13/02/26 12:30 12:30 4/30 4/30 OK Movie Play Movie Play ’13/02/26 Pausing and restarting playback Press the A button to pause playback. During pause, fast forward or reverse, press the A button to restart playback. Fast forward Press I to fast forward. Press I again to increase the fast forward speed. Rewind Press H to rewind. Press H again to increase the rewind speed. Adjusting the volume Use FG to adjust the volume. Operations while playback is paused Operations while playback is paused During pause 00:14/00:34 00:14/00:34 Elapsed time/ Total shooting time Cueing Use F to display the first frame and press G to display the last frame. Advancing and rewinding one frame at a time Press I or H to advance or rewind one frame at a time. Hold I or H pressed for continuous advance or rewind. Resuming playback Press the A button to resume playback. To stop movie playback To stop movie playback Press the  button. ● To play back movies on the computer, the supplied PC software is recommended. For the first use of the PC software, connect the camera to the computer, then launch the software.
Page: 25
25 EN Menu settings For details, refer to “List of settings available in each shooting mode” (p. 73). MENU MENU Flash Auto 0.0 0.0 AUTO WB AUTO WB AUTO ISO AUTO ISO 12M 4:3 6 7 3 2 1 5 4 8 Function menu Setup menu (p. 29) Function menu Function menu 1 Flash 5 ISO sensitivity 2 Self-timer 6 Drive 3 Exposure compensation 7 Image Size 4 White balance 8 Aspect Using the function menu 1 Use H of the arrow pad to display the function menu. 2 Use FG of the arrow pad to select the function to be set. 3 Use HI of the arrow pad to select the setting value, and then press the A button to enter the setting. Example: Exposure compensation Exposure Comp. MENU MENU 12M AUTO WB AUTO WB AUTO ISO AUTO ISO 0 0 ± 0.0 1 1 1 1 2 2 2 2 12 4:3
Page: 26
26 EN Flash Sets the flash firing method. _ Flash Auto The flash fires automatically in low-light or backlight conditions. ! Redeye Pre-flashes are emitted to reduce the occurrence of red eye in your photos. # Fill In The flash fires regardless of the available light. $ Flash Off The flash does not fire. q LED On The LED turns on when a picture is taken. This is effective for taking close up pictures. #RC Remote Control For details, see “Taking pictures with the Olympus Wireless RC Flash System” (p. 82). #SLV Slave Self-timer Sets the time after the shutter button is pressed until the picture is taken. b Y Off The self-timer is deactivated. c Y 12 sec The self-timer lamp turns on for approx. 10 seconds, then blinks for approx. 2 seconds, and then the picture is taken. d Y 2 sec The self-timer lamp blinks for approx. 2 seconds, then the picture is taken.  Auto Release When your pet (cat or dog) turns its head towards the camera, its face is recognized and the picture is taken automatically. Exposure compensation Compensates the brightness (appropriate exposure) adjusted by the camera. –2.0 to +2.0 Value Set a larger negative (–) value to adjust darker, or a larger positive (+) value to adjust brighter.
Page: 27
27 EN White balance Sets an appropriate color scheme for the light of the shooting scene. e WB Auto The camera automatically adjusts the white balance. f Sunny Suitable for shooting outdoors under a clear sky. g Cloudy Suitable for shooting outdoors under a cloudy sky. h Incandescent Suitable for shooting under tungsten lighting.  Fluorescent Suitable for shooting under white fluorescent lighting. Z Underwater Suitable for underwater shooting.  One Touch 1 For manually adjusting the white balance according to the light when shooting. Set a piece of white paper or other white object so that it fills the entire screen, and press the  button to set the white balance. For how to register one touch white balance, see “Registering one touch white balance” (p. 28).  One Touch 2 ISO sensitivity Sets the ISO sensitivity. l ISO Auto The camera automatically sets the sensitivity with priority on image quality. m High ISO Auto The camera automatically sets the sensitivity with priority on minimizing blur caused by a moving subject or by camera shake. Q to P Value Set a smaller value to reduce noise in the picture, or a larger value to reduce blur. Drive Sets the sequential shooting function. o Single One frame is shot each time the shutter button is pressed. j Sequential The images are taken sequentially while holding down the shutter for up to 100 frames. c High-Speed1 The camera takes sequential shots at approximately 15 frames/sec. d High-Speed2 The camera takes sequential shots at approximately 60 frames/sec. Image size Sets the number of recording pixels. 5 3968×2976 Suitable for printing pictures over A3 (11×17 in.). 4 3200×2400 Suitable for printing pictures up to A3 (11×17 in.). 3 1920×1440 Suitable for printing pictures up to A4 size (8.5×11 in.). 7 640×480 Suitable for using pictures on emails.
Page: 28
28 EN Aspect Sets the horizontal-to-vertical ratio of images. u 4:3 Change the horizontal-to-vertical ratio when taking pictures. v 16:9 w 3:2 x 1:1 ● In certain shooting modes, some functions cannot be set. Refer to “List of settings available in each shooting mode” (p. 73). ● Examples of image size when the aspect ratio is 4:3. Registering one touch white balance Registering one touch white balance Select [ One Touch 1] or [ One Touch 2], face the camera toward a piece of white paper or other white object, and press the  button. ● The camera releases the shutter and the white balance is registered. When the white balance was previously registered, the registered data is updated. ● The registered white balance data will not be cleared by turning off the power. ● Perform this procedure under the light where the pictures will be actually taken. ● When the camera settings are changed, the white balance must be registered again. ● When the white balance cannot be registered, check that the white paper fills the screen, and then perform the procedure again.
Page: 29
29 EN Setup menu Setup menu MENU Camera Menu 1 Back Reset Reset Off On Image Stabilizer Compression Shadow Adjust AF Mode Digital Zoom Normal Auto Face/iESP ESP ESP/ d 0 c a b e 9 9 Camera Menu 1 p. 31 z Reset Compression Shadow Adjust AF Mode ESP/n Digital Zoom Image Stabilizer (Still images) 0 Camera Menu 2 p. 33 z Accessory Settings AF Illuminat. Rec View Pic Orientation Icon Guide Date Stamp Super-Res Zoom a Movie Menu p. 37 A Image Size IS Movie Mode R (Movie sound recording) Wind Noise Setting Recording Volume b Playback Menu p. 38 q Slideshow Edit Erase Print Order R (Protect) Upload Order FlashAir c Settings Menu 1 p. 43 d Memory Format/Format Backup Eye-Fi Custom Mode Setup USB Connection q Power On Sound Settings d Settings Menu 2 p. 45 d File Name Pixel Mapping s (Monitor) Info Off TV Out Power Save l (Language) e Settings Menu 3 p. 49 d X (Date/time) World Time Beauty Settings Tough Settings GPS Settings
Page: 30
30 EN Using the setup menu Press the  button during shooting or playback to display the setup menu. The setup menu provides access to a variety of camera settings, such as shooting and playback functions, time and date settings, and display options. 1 Press the  button. ● The setup menu is displayed. MENU Camera Menu 1 Back Reset Reset ESP On Image Stabilizer Compression Shadow Adjust AF Mode Digital Zoom ESP/ Normal Auto Face/iESP Off 2 Press H to select the page tabs. Use FG to select the desired page tab and press I. Pixel Mapping Info Off Power Save Power Save Off 10sec TV Out English File Name Reset MENU Settings Menu 2 Back Page tab File Name Reset Pixel Mapping Info Off Power Save Power Save Off 10sec TV Out English MENU Settings Menu 2 Back Submenu 1 3 Use FG to select the desired submenu 1 and then press the A button. Power Save Power Save Off Pixel Mapping Info Off 10sec TV Out English File Name Reset MENU Settings Menu 2 Back Power Save Power Save Pixel Mapping Info Off TV Out File Name MENU Settings Menu 2 Back On Off Submenu 2 4 Use FG to select the desired submenu 2 and then press the A button. ● Once a setting is selected, the display returns to the Submenu 1. ● There may be additional operations. Power Save Power Save On Pixel Mapping Info Off 10sec TV Out English File Name Reset MENU Settings Menu 2 Back 5 Press the  button to complete the setting.
Page: 31
31 EN ● The default settings of the function are highlighted in . ● For the operation method, refer to “Using the setup menu” (p. 30). z Camera Menu 1 Restoring the shooting functions Restoring the shooting functions to the default settings to the default settings z z [Reset] [Reset] Submenu 2 Application Yes Restores the following menu functions to the default settings. • Aperture value • Flash • Self-timer • Exposure compensation • White balance • ISO sensitivity • Drive • Image Size (still images) • Aspect • Filter Effect • Camera Menu 1, Camera Menu 2 and Movie Menu Functions No The settings will not be changed. Selecting the image quality for still Selecting the image quality for still images images z z [Compression] [Compression] Submenu 2 Application Fine Shooting at high quality. Normal Shooting at normal quality. ● “Number of storable pictures (still images)/ Recording length (movies) in the internal memory and cards” (p. 81) Brightening the subject against Brightening the subject against backlight backlight z z [Shadow Adjust] [Shadow Adjust] Submenu 2 Application Auto Automatically On when a compatible shooting mode is selected. Off The effect is not applied. On Shoot with automatic adjustment to brighten an area that has become darker. ● When [ESP/n] is set to [n], [Shadow Adjust] is automatically fixed to [Off].
Page: 32
32 EN Selecting the focusing area Selecting the focusing area z z [AF Mode] [AF Mode] Submenu 2 Application Face/iESP The camera focuses automatically. (If a face is detected, it is shown by a white frame*1 ; when the shutter button is pressed halfway and the camera focuses, the frame turns to green*2 . If no face is detected, the camera chooses a subject in the frame and focuses automatically.) Spot The camera focuses on the subject located within the AF target mark. AF Tracking The camera tracks the subject movement automatically to focus on it continuously. *1 For some subjects, the frame may not appear or may take some time to appear. *2 If the frame blinks in red, the camera cannot focus. Try refocusing on the subject. ● [AF Tracking] is enabled in the optical zoom area. To focus on a moving subject To focus on a moving subject continuously (AF Tracking) continuously (AF Tracking) 1 Hold the camera to align the AF target mark on the subject and press the A button. 2 When the camera recognizes the subject, the AF target mark automatically tracks the subject movement to focus on it continuously. 3 To cancel the tracking, press the A button. ● Depending on the subjects or the shooting conditions, the camera may be unable to lock the focus or fail to track the subject movement. ● When the camera fails to track the subject movement, the AF target mark changes to red. Selecting the method for Selecting the method for measuring the brightness measuring the brightness z z [ESP/ [ESP/n n] ] Submenu 2 Application ESP Shoots to obtain a balanced brightness over the entire screen (Meters the brightness at the center and surrounding areas of the screen separately). 5 (spot) Shoots the subject at the center during backlighting (Meters the brightness at the center of the screen). ● When set to [ESP], the center may appear dark when shooting against strong backlighting.
Page: 33
33 EN Shooting at higher magnifications Shooting at higher magnifications than optical zoom than optical zoom z z [Digital Zoom] [Digital Zoom] Submenu 2 Application Off Disable digital zoom. On Enable digital zoom. ● The option selected for [Digital Zoom] affects the appearance of the zoom bar. (p. 36) Reducing the blur caused by the Reducing the blur caused by the camera shake when shooting camera shake when shooting z z [Image Stabilizer] [Image Stabilizer] Submenu 2 Application Off The image stabilizer is deactivated. This is recommended for shooting when the camera is fixed in place on a tripod or other stable surface. On The image stabilizer is activated. ● There may be a noise coming from inside the camera when the shutter button is pressed with [Image Stabilizer] set to [On]. ● Images may not be stabilized if camera shake is too severe. ● When the shutter speed is extremely slow, such as when taking pictures at night, [Image Stabilizer] may not be as effective. z Camera Menu 2 Using separately sold accessories Using separately sold accessories z z [Accessory Settings] [Accessory Settings] Submenu 2 Submenu 3 Application Remote Flash Off The external flash is not available. RC An Olympus Wireless RC Flash System compatible flash is used for taking pictures. (Channel: CH1, Group: A) Slave The commercially- available slave flash that is synchronized with the camera flash is used for taking pictures. The flash intensity setting can be adjusted. Conversion Lens Off Select when taking pictures without a conversion lens. PTWC-01 Select depending on designated optional conversion lenses. FCON-T01 TCON-T01 ● “Taking pictures with the Olympus Wireless RC Flash System” (p. 82) ● “Use the conversion lens (sold separately)” (p. 83)
Page: 34
34 EN Using the assist lamp for shooting Using the assist lamp for shooting a dark subject a dark subject z z [AF Illuminat.] [AF Illuminat.] Submenu 2 Application Off The AF illuminator is not used. On When the shutter button is pressed halfway down, the AF illuminator turns on to aid focusing. AF illuminator Viewing the image immediately Viewing the image immediately after shooting after shooting z z [Rec View] [Rec View] Submenu 2 Application Off The image being recorded is not displayed. This allows the user to prepare for the next shot while following the subject in the monitor after shooting. On The image being recorded is displayed. This allows the user to make a brief check of the image that was just taken. Automatically rotating images Automatically rotating images shot with the camera in a vertical shot with the camera in a vertical position during playback position during playback z z [Pic Orientation] [Pic Orientation] ● During shooting, the [y] (p. 41) setting on the playback menu is set automatically. ● This function may not work properly if the camera is facing up or down during shooting. Submenu 2 Application Off Information about the vertical/ horizontal orientation of the camera during shooting is not recorded with images. Images shot with the camera in a vertical position are not rotated during playback. On Information about the vertical/ horizontal orientation of the camera during shooting is recorded with images. Images are automatically rotated during playback.
Page: 35
35 EN Displaying icon guides Displaying icon guides z z [Icon Guide] [Icon Guide] Submenu 2 Application Off No icon guide is displayed. On The explanation of the selected icon will be displayed when a shooting mode or function menu icon is selected (position the cursor on the icon for a while to display the explanation). Icon guide MENU MENU 0.0 0.0 12M AUTO WB AUTO WB AUTO ISO AUTO ISO 6400 ISO ISO 100 ISO ISO 100 HIGH ISO ISO HIGH 6400 ISO Auto The camera will automatically set the ISO sensitivity for optimal image quality. 12 4:3 Imprinting the date of recording Imprinting the date of recording z z [Date Stamp] [Date Stamp] Submenu 2 Application Off Do not imprint the date. On Stamp new photographs with the date of recording. ● When the date and time are not set, [Date Stamp] cannot be set. “Turning on the camera and making the initial settings” (p. 7) ● The date stamp can not be deleted. ● When drive settings are set to other than [o], [Date Stamp] cannot be set.
Page: 36
36 EN Shooting larger pictures than when using optical zoom with low Shooting larger pictures than when using optical zoom with low degrading of image quality degrading of image quality z z [Super-Res Zoom] [Super-Res Zoom] Submenu 2 Application Off Disable super-resolution zoom. On Enable super-resolution zoom. ● [Super-Res Zoom] is available only when [Image Size] is set to [5]. Super-resolution zoom Digital zoom Image size Zoom bar On Off 12M Super-resolution zoom Off On 12M Digital zoom Other *1 On On 12M Super-resolution zoom Digital zoom *1 Due to increased processing of the pixel counts, the image quality will not degrade. The magnification ratio changes depending on the image size setting. ● Photographs taken with the zoom bar displayed in red may appear “grainy”.
Page: 37
37 EN A Movie Menu Selecting the image size for Selecting the image size for movies movies A A [Image Size] [Image Size] Submenu 2 Application 1080p 720p VGA (640×480) HS 120fps*1 (640×480) HS 240fps*1 (320×240) Select the image quality based on the image size and frame rate. *1 HS: Film quickly moving subjects for slow-motion playback. Only available in P mode. ● “Number of storable pictures (still images)/ Recording length (movies) in the internal memory and cards” (p. 81) Reducing the blur caused by the Reducing the blur caused by the camera shake when shooting camera shake when shooting A A [IS Movie Mode] [IS Movie Mode] Submenu 2 Application Off The image stabilizer is deactivated. This is recommended for shooting when the camera is fixed in place on a tripod or other stable surface. On The image stabilizer is activated. ● Images may not be stabilized if camera shake is too severe. ● In HS movie mode, this setting is fixed to [Off]. Recording sound when shooting Recording sound when shooting movies movies A A [ [R R] ] Submenu 2 Application Off No sound is recorded. On Sound is recorded. ● Sound is not recorded when an HS movie mode is selected. Reduce wind noise in the recorded Reduce wind noise in the recorded sound when recording movie sound when recording movie A A [Wind Noise Setting] [Wind Noise Setting] Submenu 2 Application Off Disable Wind Noise Reduction. On Uses Wind Noise Reduction. Adjusting the microphone volume Adjusting the microphone volume A A [Recording Volume] [Recording Volume] Submenu 2 Application Normal Set the microphone level to Normal for general use. Low Set the microphone level to Low not to produce clipping sound when the microphone level is high.
Page: 38
38 EN q Playback Menu Playing back images automatically Playing back images automatically q q [Slideshow] [Slideshow] Submenu 2 Submenu 3 Application BGM Off/Cosmic/ Breeze/ Mellow/ Dreamy/ Urban Selects the background music options. Type Normal/ Fader/ Zoom Selects the type of transition effect used between slides. Start ― Starts the slideshow. ● During a slideshow, press I to advance one frame, H to go back one frame. ● Press the  button or the i button to stop the slideshow. Changing the image size Changing the image size q q [ [Q Q] ] This saves a high-resolution image as a separate image with a smaller size for use in e-mail attachments and other applications. Submenu 1 Submenu 2 Submenu 3 Edit Q n  1 Use HI to select an image. 2 Use FG to select an image size and press the A button. ● The resized image is saved as a separate image. Cropping image Cropping image q q [ [P P] ] Submenu 1 Submenu 2 Edit P 1 Use HI to select an image, and press the A button. 2 Use the zoom buttons to select the size of the cropping frame, and use FGHI to move the frame. Cropping frame MENU Back 3 Press the A button after you have selected the area to trim. ● The edited image is saved as a separate image.
Page: 39
39 EN Adding sound to still images Adding sound to still images q q [ [R R] ] Submenu 1 Submenu 2 Edit R 1 Use HI to select an image. 2 Aim the microphone toward the sound source. Microphone 3 Press the A button. ● Recording starts. ● The camera adds (records) sound for approx. 4 seconds while playing back the image. Retouching faces on still images Retouching faces on still images q q [Beauty Fix] [Beauty Fix] Submenu 1 Submenu 2 Edit Beauty Fix ● Depending on the picture, the editing may not be effective. 1 Use HI to select an image, and press the Q button. 2 Use FG to select a retouching item, and press the Q button. 3 To save the image, select [OK] on the review screen and press the Q button. To retouch the image additionally, select [Beauty Fix]. ● The retouched image is saved as a separate image. OK Beauty Fix MENU Back ● The [Image Size] of the retouched image is limited to [3] or lower.
Page: 40
40 EN Beauty Fix Beauty Fix 1 Select a retouching item and retouching level, and press the A button. MENU Off Eye Color Back 2 Press the Q button on the review screen. Brightening areas that are dark Brightening areas that are dark due to backlight or other reasons due to backlight or other reasons q q [Shadow Adj] [Shadow Adj] Submenu 1 Submenu 2 Edit Shadow Adj 1 Use HI to select an image, and press the A button. ● The edited image is saved as a separate image. ● Depending on the picture, the editing may not be effective. ● The retouching process may lower the image resolution. Retouching red eyes in flash Retouching red eyes in flash shooting shooting q q [Redeye Fix] [Redeye Fix] Submenu 1 Submenu 2 Edit Redeye Fix 1 Use HI to select an image, and press the A button. ● The edited image is saved as a separate image. ● Depending on the picture, the editing may not be effective. ● The retouching process may lower the image resolution. Changing the landmark Changing the landmark information recorded on the information recorded on the images images q q [Landmark] [Landmark] You can change the landmark information (such as place names and names of buildings) recorded on the images when they were shot using the GPS function to different landmark information registered near the place where you shot the images. Submenu 1 Submenu 2 Edit Landmark ● Refer to “Recording the shooting location and time information on the images shot d [GPS Settings]” (p. 55). 1 Select the image using HI, and press the A button. ● If the target landmark is at a distance from the position recorded on the images, it may not be displayed. ● A list of the landmarks registered near the position recorded on the images are displayed.
Page: 41
41 EN 2 Select the new landmark to be recorded on the image using FG, and press the A button. 3 Select [OK] using FG, and press the A button. Rotating images Rotating images q q [ [y y] ] Submenu 1 Submenu 2 Edit y 1 Use HI to select an image. 2 Press the A button to rotate the image. 3 If necessary, repeat Steps 1 and 2 to make settings for other images, and press the  button. ● The new picture orientations will be saved even after the power is turned off. Erasing images Erasing images q q [Erase] [Erase] Submenu 2 Application All Erase All images in the internal memory or card will be erased. Sel. Image Images are individually selected and erased. Erase Deletes the image displayed. Erase Group All images in the group are erased. ● When erasing pictures in the internal memory, do not insert the card into the camera. ● Protected images cannot be erased. To individually select and erase images To individually select and erase images [Sel. Image] [Sel. Image] 1 Use FG to select [Sel. Image], and press the A button. 2 Use FGHI to select the image to be erased, and press the A button to add a R mark to the image. ● Press the T button to the single frame display. Sel. Image (1) Erase/Cancel OK MENU 4/30 4/30 R mark
Page: 42
42 EN 3 Repeat Step 2 to select the images to be erased, and then press the  button to erase the selected images. 4 Use FG to select [Yes], and press the A button. ● The images with a R mark are erased. To erase all images [All Erase] To erase all images [All Erase] 1 Use FG to select [All Erase], and press the A button. 2 Use FG to select [Yes], and press the A button. Saving print settings to the image Saving print settings to the image data data q q [Print Order] [Print Order] ● “Print Reservations” (p. 63) ● Print reservation can be set only for still images that are recorded to the card. Protecting images Protecting images q q [ [R R] ] ● Protected images cannot be erased by [Erase] (p. 23, 41), [Sel. Image] (p. 41), [Erase Group] (p. 41), or [All Erase] (p. 41), but all images are erased by [Memory Format]/[Format] (p. 43). 1 Use HI to select an image. 2 Press the A button. ● Press the A button again to cancel the settings. 3 If necessary, repeat Steps 1 and 2 to protect other images, and press the  button. ● If you protect the grouped images, all images in the group will be protected at once. Setting images to upload to Setting images to upload to Internet using OLYMPUS Viewer 3 Internet using OLYMPUS Viewer 3 q q [Upload Order] [Upload Order] 1 Use HI to select an image. 2 Press the A button. ● Press the A button again to cancel the settings. 3 If necessary, repeat Steps 1 and 2 to make settings for other images, and press the  button. ● Only JPEG files can be ordered. ● For details on OLYMPUS Viewer 3, refer to “Installing the PC software and registering user” (p. 57). ● For details on uploading images, refer to OLYMPUS Viewer 3 “Help”.
Page: 43
43 EN Connecting to Smartphone Connecting to Smartphone q q [FlashAir] [FlashAir] ● Using the FlashAir (with Wireless LAN function) card (commercially available), you can connect the camera to a Wi-Fi enabled smartphone or PC and view or import images from the FlashAir card. ● When using a FlashAir card, read the FlashAir card instruction manual carefully, and comply with the instructions. Submenu 2 Application Start/Stop Connect to or disconnect from Wi-Fi. Starting option [Manual Start] or [Auto Start] can be selected. ● The camera will not go into sleep mode while connected to Wi-Fi. ● Smartphone application is available. http://olympuspen.com/OIShare/ ● Before use, refer to “FlashAir/Eye-Fi card” (p. 79). d Settings Menu 1 Erasing data completely Erasing data completely d d [Memory Format]/ [Memory Format]/ d d [Format] [Format] ● Before formatting, check that no important data is left in the internal memory or card. ● Cards must be formatted with this camera before first use or after being used with other cameras or computers. ● Be sure to remove the card before formatting the internal memory. Submenu 2 Application Yes Completely erases the image data in the internal memory or card (including protected images). No Cancels formatting. Copying images in the internal Copying images in the internal memory to the card memory to the card d d [Backup] [Backup] Submenu 2 Application Yes Backs up image data in the internal memory to the card. No Cancels the backup.
Page: 44
44 EN Using an Eye-Fi card Using an Eye-Fi card d d [Eye-Fi] [Eye-Fi] Submenu 2 Application All Transfers all images. Sel. Image Transfers only selected image. Off Disable Eye-Fi communication. ● When using an Eye-Fi card, read the Eye-Fi card instruction manual carefully, and comply with the instructions. ● This camera does not support the Eye-Fi card’s Endless mode. ● Before use, refer to “FlashAir/Eye-Fi card” (p. 79). Saving custom settings Saving custom settings d d [Custom Mode Setup] [Custom Mode Setup] The screen to select the Custom Mode 1 or Custom Mode 2 is displayed. Submenu 2 Application Set Save current settings. Reset Return to the default setting. Selecting a method for connecting Selecting a method for connecting the camera to other devices the camera to other devices d d [USB Connection] [USB Connection] Submenu 2 Application Auto Set to select the connection method each time the camera is connected to another device. Storage Connect camera as a card reader. MTP For Windows Vista/Windows 7/ Windows 8, connect camera as a portable device. Print Select when connecting to a PictBridge-compatible printer. ● When using the supplied software, select [Storage]. ● Refer to “Connecting with a computer” (p. 56) for the connection method with a computer.
Page: 45
45 EN Turning on the camera with the Turning on the camera with the q q button button d d [ [q q Power On] Power On] Submenu 2 Application No The camera is not turned on. To turn on the camera, press the n button. Yes Press and hold the q button to turn the camera on in the playback mode. Selecting the camera sound and Selecting the camera sound and its volume its volume d d [Sound Settings] [Sound Settings] Submenu 2 Submenu 3 Application Sound Type 1/2/3 Selects the camera sounds (operation sounds, shutter sound, and warning sound). Volume 0/1/2/3/4/5 Selects the operation volume of camera buttons. q Volume 0/1/2/3/4/5 Selects the image playback volume. d Settings Menu 2 Resetting the file names of Resetting the file names of pictures pictures d d [File Name] [File Name] Month: 1 to C (A=October, B=November, C=December) Day: 01 to 31 Pmdd Folder name Folder name File name DCIM 100OLYMP 999OLYMP Pmdd0001.jpg Pmdd9999.jpg Automatic numbering Automatic numbering
Page: 46
46 EN Submenu 2 Application Reset This resets the sequential number for the folder name and file name whenever a new card is inserted.*1 This is useful when grouping images on separate cards. Auto Even when a new card is inserted, this continues the numbering for the folder name and file name from the previous card. This is useful for managing all image folder names and files names with sequential numbers. *1 The number for the folder name is reset to 100, and the one for the file name is reset to 0001. Adjusting the image processing Adjusting the image processing function function d d [Pixel Mapping] [Pixel Mapping] ● This function has already been adjusted at factory shipping, and no adjustment is needed right after purchase. Approximately once a year is recommended. ● For best results, wait at least one minute after taking or viewing pictures before performing pixel mapping. If the camera is turned off during pixel mapping, be sure to perform it again. To adjust the image processing function To adjust the image processing function Press the A button when [Start] (Submenu 2) is displayed. ● The check and adjustment of the image processing function starts. Adjusting the brightness of the Adjusting the brightness of the monitor monitor d d [ [s s] ] To adjust the monitor brightness To adjust the monitor brightness 1 Use FG to adjust the brightness while viewing the screen, and then press the A button. MENU Back s Displaying indicators Displaying indicators d d [Info Off] [Info Off] Submenu 2 Application 10sec Indicators automatically clear from the display if no operations are performed for 10 seconds. Hold Indicators are always displayed during shooting. ● Indicators that are always displayed may “burn in” to the monitor. “Monitor” (p. 99)
Page: 47
47 EN Playing back images on a TV Playing back images on a TV d d [TV Out] [TV Out] The TV video signal system varies depending on the countries and regions. Before viewing camera images on your TV, select the video output according to your TV’s video signal type. Submenu 2 Submenu 3 Application NTSC/PAL NTSC Connecting the camera to a TV in North America, Taiwan, Korea, Japan, and so on. PAL Connecting the camera to a TV in European countries, China, and so on. HDMI Out 480p/576p 720p 1080i Set the signal format to be given priority. If the TV setting does not match, it is changed automatically. HDMI Control Off Operate with the camera. On Operate with the TV remote control. The factory default settings differ according to the region where the camera is sold. To play back camera images on a TV To play back camera images on a TV ● Connection via AV cable 1 Use the camera to select the same video signal system as the one of connected TV ([NTSC]/[PAL]). 2 Connect the TV and camera. ● Connection via HDMI cable 1 On the camera, select the digital signal format that will be connected ([480p/576p]/[720p]/[1080i]). 2 Connect the TV and camera. 3 Turn on the TV, and change “INPUT” to “VIDEO (an input jack connected to the camera)”. 4 Turn on the camera, and use FGHI to select the image for playback. ● When the camera is connected to the computer by the USB cable, do not connect the HDMI cable to the camera.
Page: 48
48 EN Connect to the TV video input jack (yellow) and audio input jack (white). Connect to the HDMI connector on the TV. HDMI micro connector (type D) HDMI cable (sold separately: CB-HD1) AV cable (sold separately: CB-AVC3) Multi-connector ● For details on changing the input source of the TV, refer to the TV’s instruction manual. ● When the camera and TV are connected by both an AV cable and an HDMI cable, the HDMI cable will take priority. ● Depending on the TV’s settings, the displayed images and information may become cropped. To operate images with the TV remote control To operate images with the TV remote control 1 Set [HDMI Control] to [On], and turn off the camera. 2 Connect the camera and TV with an HDMI cable. “Connection via HDMI cable” (p. 47) 3 First turn on the TV, and then turn on the camera. ● Operate by following the operation guide that is displayed on the TV. ● With some TVs, operations cannot be performed with the TV remote control even though the operation guide is displayed on the screen. ● If operations cannot be performed with the TV remote control, set [HDMI Control] to [Off] and operate using the camera.
Page: 49
49 EN Saving battery power between Saving battery power between shots shots d d [Power Save] [Power Save] Submenu 2 Application Off Cancels [Power Save]. On When the camera is not being used for approx. 10 seconds, the monitor automatically turns off to save battery power. To resume standby mode To resume standby mode Press any button. Changing the display language Changing the display language d d [ [l l] ] Submenu 2 Application Languages The language for the menus and error messages displayed on the monitor is selected. d Settings Menu 3 Setting the date and time Setting the date and time d d [ [X X] ] 1 Press FG of the arrow pad to select the year for [Y]. 2 Press I of the arrow pad to save the setting for [Y]. 3 As in Steps 1 and 2, press FGHI of the arrow pad to set [M] (month), [D] (day), [Time] (hours and minutes), and [Y/M/D] (date order), and then press the A button. ● For precise time setting, press the A button as the time signal strikes 00 seconds. To check the date and time To check the date and time Press the INFO button while the camera is turned off. The current time is displayed for approx. 30 seconds.
Page: 50
50 EN Choosing home and alternate time Choosing home and alternate time zones zones d d [World Time] [World Time] ● You will not be able to select a time zone using [World Time] if the camera clock has not first been set using [X]. Submenu 2 Submenu 3 Application Home/ Alternate x The time in the home time zone (the time zone selected for x in submenu 2). z The time in the travel destination time zone (the time zone selected for z in submenu 2). x*1 — Select the home time zone (x). z*1, 2 — Select the travel destination time zone (z). *1 In areas where daylight saving time is in effect, use FG to turn daylight saving time ([Summer]) on. *2 When you select a time zone, the camera automatically calculates the time difference between the selected zone and the home time zone (x) to display the time in the travel destination time zone (z). Registering the settings for Beauty Registering the settings for Beauty Fix Fix d d [Beauty Settings] [Beauty Settings] ● Depending on the picture, the editing may not be effective. 1 Use FG to select a retouching setting, and press the Q button. 2 Press the shutter button to take a portrait picture. Take a portrait picture. ● The image is not saved. 3 Select a retouching item and retouching level, and press the A button. MENU Off Eye Color Back 4 Press the Q button on the review screen to save the image. ● Registration is complete.

Question & answers

Have a question about the Olympus Tough TG-2 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Olympus Tough TG-2. Please make sure that you describe your difficulty with the Olympus Tough TG-2 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Olympus Tough TG-2

Name
Email
Reaction

View a manual of the Olympus Tough TG-2 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Olympus
  • Product: Digital cameras
  • Model/name: Tough TG-2
  • Filetype: PDF
  • Available languages: English, Italian, German