PT-EP05L

Olympus PT-EP05L manual

PT-EP05L

User manual for the Olympus PT-EP05L in English. This PDF manual has 27 pages.

Page: 1
©2011 http://www.olympus.com/ VR808501 Printed in China PT-EP05L/06L Jp 取扱説明書 Instruction Manual En Mode d’emploi Fr Bedienungsanleitung De Manual de instrucciones Sp Cs Kr PT-EP05L/06L Instruction Manual PT-EP05L_06L_JP-COVER.fm 1 ページ 2011年7月15日 金曜日 午前10時15分
Page: 2
EN 1 En Introduction z Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. z OLYMPUS IMAGING CORP. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use z This Case is a precision device designed for use at a water depth within 45 m. Please handle it with sufficient care. z Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. z OLYMPUS IMAGING CORP. shall not be responsible for accidents involving immersion of a digital camera in water. In addition, expenses incurred for damage of internal materials or loss of recorded contents due to water entering the camera will not be compensated. z OLYMPUS IMAGING CORP. shall not pay any compensation for accidents (injuries or material damage) at the time of use. For safe use This instruction manual uses various pictographs for correct use of the product and to prevent danger to the user and other person, as well as property damage. These pictographs and their meanings are shown below. „ Thank you for buying the Underwater Case PT-EP05L/06L (hereinafter Case). „ Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. „ Wrong usage may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. „ Before use, perform an advance check as described in this manual. WARNING This shows the content regarding assumption of possibility of human death or severe injury in case of handling with disregard of this indication. CAUTION This shows the contents regarding assumption of possibility of injury or damage to property in case of handling with disregard of this indication. PT-EP05L_06L_EN.Book Page 1 Friday, July 15, 2011 10:30 AM
Page: 3
EN 2 En WARNING 1 Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. • Injury by dropping onto the body from heights. • Injury from parts of the body getting caught in parts which open and close. • Swallowing of small parts, O-ring, silicone grease and silica gel. Please consult a physician immediately if any parts have been swallowed. 2 Do not store this product with batteries for light or a digital camera still containing batteries loaded in it. Storage with batteries inserted may lead to battery leakage and fire hazard. 3 If leakage of water should occur with a camera installed in this product, quickly remove the batteries from the camera or the Case. There is the possibility of ignition and explosion from generation of hydrogen gas. 4 This product is made of resin. There is the possibility that injuries may be caused when it becomes broken due to strong impact with a rock or other hard objects. Please handle it with sufficient care. 5 Do not look directly at the light when it is on. CAUTION 1 Do not disassemble or modify this product. This may cause water leakage or defect. In case of the loss of image data caused by disassembly, repair or modification etc. by any party other than those appointed by OLYMPUS IMAGING CORP., we shall bear no responsibility for damage. 2 Use or storage of the product at the following locations may cause defective operation, defects, damage, fire, internal fogging, or water leakage. This should be avoided. • Locations reaching high temperatures such as those under direct sunlight, in an automobile, etc. • Locations close to fire • A water depth in excess of 45 m • Locations subject to vibrations For customers in Europe The "CE" mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. CE-mark products are for sale in Europe. This symbol [crossed-out wheeled bin WEEE Annex IV] indicates separate collection of waste electrical and electronic equipment in the EU countries. Please do not throw the equipment into the domestic refuse. Please use the return and collection systems available in your country for the disposal of this product. For customers in USA FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized changes or modifications to this equipment would void the user's authority to operate. For customers in CANADA This Class B digital apparatus complies with Canadian ICES-003. PT-EP05L_06L_EN.Book Page 2 Friday, July 15, 2011 10:30 AM
Page: 4
EN 3 En • Locations with high temperature and humidity or with extreme temperature changes • Locations with volatile substances 3 Opening and closing at locations with much sand, dust, or dirt may impair the waterproof characteristic and cause water leakage. This should be avoided. 4 This product is not a case to soften impacts to the camera inside the product. When this product with a digital camera inside is subjected to impacts or heavy objects are placed onto it, the digital camera may be damaged. Please handle it with sufficient care. 5 Do not use the following chemicals for cleaning, corrosion prevention, prevention of fogging, repair or other purposes. When these are used for the Case directly or indirectly (with the chemicals in vaporized state), they may cause cracking under high pressure or other problems. 6 Jumping into the water with the Case in your hand, throwing the Case from a boat or ship into the water, and other rough handling may cause water leakage. Please handle with sufficient care, when handing it over from hand to hand etc. 7 There is the light circuitry inside, so do not let the inside of the Case getting wet. 8 If the Case interior or the camera should become wet because of water leakage, etc., immediately wipe off all moisture and contact your local service station or dealer. 9 Be careful not to apply excessive force to the zoom dial, accessory mount or tripod seat. 0 Remove the O-ring when traveling by air. Otherwise air pressure may make it impossible to open the Case. a For safe use of the digital camera in this product, please read the “Instruction Manual” for the digital camera carefully. b When sealing this product, take sufficient care that no foreign matter gets caught at the O-ring and the contact surface. It is caused for water leakage. c The lens port cannot be removed. d Do not use as an underwater torch for diving. Chemicals which cannot be used Explanation Volatile organic solvents, chemical detergents Do not clean the Case with alcohol, gasoline, thinner or other volatile organic solvents or with chemical detergents etc. Pure water or lukewarm water is sufficient for cleaning. Anticorrosion agent Do not use anticorrosion agents. Pure water is sufficient when washing the metal parts as stainless steel and brass are used. Commercial defogging agents Do not use commercial defogging agents. Always use the specified desiccant silica gel. Grease other than specified silicone grease Use only the specified silicone grease for the O-ring, as otherwise the O-ring surface may deteriorate and water leakage may occur. Adhesive Do not use adhesive for repairs or other purposes. When repair is required, please contact a dealer or a service station of OLYMPUS IMAGING CORP. PT-EP05L_06L_EN01.fm Page 3 Thursday, July 21, 2011 11:18 AM
Page: 5
EN 4 En Battery handling precautions Follow these important guidelines to prevent batteries from leaking, overheating, burning, exploding, or causing electrical shocks or burns. DANGER z Never heat or incinerate batteries. z Never contact terminals (+) and (–) with metal. z Do not use solder, transform, modify or dismantle the batteries. WARNING z Keep batteries dry at all times. z Do not touch the batteries with wet hands. z Use only batteries recommended for use with this product. z Never mix batteries (old and new batteries, charged and uncharged batteries, batteries of different manufacture or capacity, etc.). z If a battery leaks, becomes discolored or deformed, or becomes abnormal in any other way during operation, stop using it. It may cause a fire or an electrical shock. Please contact your local service station or dealer. z Always remove batteries if they are not used for a long period. PT-EP05L_06L_EN.Book Page 4 Friday, July 15, 2011 10:30 AM
Page: 6
EN 5 En Introduction ............................................................................................................................ 1 Please read the following items before use ........................................................................... 1 For safe use ........................................................................................................................... 1 Battery handling precautions.................................................................................................. 4 1.Preparations .........................................................................................................7 Check the contents of the package........................................................................................ 7 Names of the parts........................................................................................................... 8 Using the accesories.............................................................................................................. 9 Installing and removing of the LCD hood......................................................................... 9 Mounting and removing the body cap.............................................................................. 9 Installing the diffuser...................................................................................................... 10 2.Advance check of the Case...........................................................................11 Advance check before use................................................................................................... 11 3.Loading the digital camera............................................................................12 Check the digital camera...................................................................................................... 12 Open the Case ..................................................................................................................... 13 Attach the flash to the camera and raise the light emitting part ........................................... 13 Insert the batteries for the light............................................................................................. 14 Load the digital camera........................................................................................................ 15 Make sure the camera is loaded properly ............................................................................ 15 Seal the Case....................................................................................................................... 16 Attach the diffuser ................................................................................................................ 16 Check the operation of the loaded camera .......................................................................... 16 Water leakage test ............................................................................................................... 17 4.Connecting the underwater flash................................................................18 Connecting the underwater optical fiber cable ..................................................................... 18 5.Installing the underweater conversion lens ............................................19 6.Taking pictures under water.........................................................................20 Select the shooting modes................................................................................................... 20 Underwater shooting modes ................................................................................................ 20 7.Handling after shooting ..................................................................................21 Wipe off any waterdrop ........................................................................................................ 21 Unload the digital camera and batteries............................................................................... 21 Wash the Case with pure water ........................................................................................... 21 Dry the Case ........................................................................................................................ 22 8.Maintaining the waterproof function..........................................................23 Remove the O-ring............................................................................................................... 23 Remove any sand, dirt, etc. ................................................................................................. 23 Contents PT-EP05L_06L_EN.Book Page 5 Friday, July 15, 2011 10:30 AM
Page: 7
EN 6 En Install the O-ring................................................................................................................... 23 Applying grease to the O-ring .............................................................................................. 24 Replace consumable products............................................................................................. 24 9.Appendix ..............................................................................................................25 Specifications ....................................................................................................................... 25 Supplied accessories for PT-EP05L/06L ....................................................................... 25 Optional accessories...................................................................................................... 25 PT-EP05L_06L_EN.Book Page 6 Friday, July 15, 2011 10:30 AM
Page: 8
EN 7 En 1. Preparations Check the contents of the package Check that all accessories are in the box. Contact your dealer if accessories are missing or damaged. CAUTION: • After purchase, be sure to do maintenance even in brand-new condition. Neglecting the maintenance may become the cause of water leakage. For how to maintenance the case, refer to P.23. • The zoom gear PPZR-EP02 (sold separately) is required to use the zoom. For details, refer to P.12. • Silica gel (1g) • Silicone grease • O-ring remover • Case body (Check that the O-ring is installed.) • LCD hood (on the body) • Body cap • Flash window cover • Diffuser • Instruction manual (this manual) • Antireflective ring • Optical fiber cable insertion slot cap (2) • Hand strap PT-EP05L_06L_EN.Book Page 7 Friday, July 15, 2011 10:30 AM
Page: 9
EN 8 En Names of the parts Note: Case operation parts marked by * corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera. PT-EP05L PT-EP06L 1 Open/close dial 2 Slide lock *3 Shutter lever *4 ON/OFF button 5 Accessory mount 6 Light ON/OFF button 7 Light 8 Optical fiber cable insertion slots 9 Zoom dial *0 q (Play) button *a (Erase) button *b Mode dial knob *c G/Fn button (PT-EP05L) *d U button (PT-EP05L) *e ( (REC) button *f INFO (Info display) button *g F (Exposure correction) button/Cross-cursor button S *h # button/Cross-cursor button X (PT-EP05L) *i OK button *j jY button/Cross-cursor button T *k MENU button *l P button/Cross-cursor button W (PT-EP05L) m LCD monitor window n LCD hood o # button/U button/Cross- cursor button X (PT-EP06L) p P button/G button/ Cross-cursor button W (PT-EP06L) q O-ring r LCD inner hood s Tripod seat t Battery box PT-EP05L_06L_EN.Book Page 8 Friday, July 15, 2011 10:30 AM
Page: 10
EN 9 En Using the accesories Installing and removing of the LCD hood Installation Fit the LCD hood as shown in the figure into the rails above and below the LCD monitor window one after the other. Removal Remove the LCD hood from the rails above and below the LCD monitor window one after the other by widening the LCD hood. Mounting and removing the body cap Install to fit the concave and convex parts of the body cap and lens port. Be sure to remove the body cap before shooting. Rails Installation Removal PT-EP05L_06L_EN.Book Page 9 Friday, July 15, 2011 10:30 AM
Page: 11
EN 10 En Installing the diffuser 1 Attach the diffuser to the port adapter. 2 Attach the hand strap on the Case body. 3 Install the diffuser on the Case. Port adapter Diffuser PT-EP05L_06L_EN.Book Page 10 Friday, July 15, 2011 10:30 AM
Page: 12
EN 11 En 2. Advance check of the Case Advance check before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications. However, depending on the carrying, storage conditions and the maintenance status, etc., the waterproof function may be damaged. Before using, always perform the following advance checks. Advance check 1 Before loading the digital camera in the Case, immerse the empty Case to confirm that there is no water leakage. When it is difficult, water leakage can be checked by referring “Water leakage test” (P. 17). 2 Main causes of water leakage are as follows. • Forgetting to install the O-ring • Part of an O-ring or an entire O-ring is outside the specified groove. • O-ring damage, cracks, deterioration or deformation • Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring contact surface. • Damage to an O-ring groove or O-ring contact surface. • Attached strap or silica gel getting caught when closing the Case. Perform the test after the above causes have been eliminated. CAUTION: If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station. PT-EP05L_06L_EN.Book Page 11 Friday, July 15, 2011 10:30 AM
Page: 13
EN 12 En 3. Loading the digital camera Check the digital camera Check the digital camera before loading it in the Case. 1. Battery confirmation It is impossible to change the batteries when using the Case. Make sure that you have sufficient remaining battery capacity before use. 2. Check the remaining number of pictures Check that the image storage medium has enough room for the number of pictures you want to take. 3. Remove the strap, lens cap and filter from the digital camera. If the digital camera is loaded without removing the strap, lens cap and the Case cannot be sealed properly and water leakage may be caused. 4. When using PT-EP05L, insert the back monitor of the camera. 5. Attach the zoom gear (optional) and the antireflective ring. POSR-EP03 cannot be used. Zoom gear Antireflective ring M.ZUIKO DIGITAL ED 14-42mm II M.ZUIKO DIGITAL ED 14-42mm II R PPZR-EP02 POSR-EP05 (supplied) Antireflective ring PT-EP05L_06L_EN.Book Page 12 Friday, July 15, 2011 10:30 AM
Page: 14
EN 13 En Open the Case 1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial clockwise (2). 2 Open the rear lid of the Case gently. Attach the flash to the camera and raise the light emitting part Attach the flash supplied with the camera. Make sure to raise the light emitting part. CAUTION: Do not apply too much force while turning the open/close dial. Doing so may damage the dial. 1 2 Slide lock PT-EP05L_06L_EN.Book Page 13 Friday, July 15, 2011 10:30 AM
Page: 15
EN 14 En Insert the batteries for the light Open the battery lid. Insert 2 AAA batteries on the ribbon. Pay attention to the battery direction. Close the battery lid. PT-EP05L_06L_EN.Book Page 14 Friday, July 15, 2011 10:30 AM
Page: 16
EN 15 En Load the digital camera 1 Confirm that the digital camera is OFF. 2 Gently load the digital camera into the Case. 3 Insert a silica gel bag (1g) between the bottom of the digital camera and the Case. The silica gel bag provided for prevention of fogging. Make sure the camera is loaded properly Check the following points before sealing the Case. • Is the digital camera loaded properly? • Is silica gel inserted all the way at the specified location? • Is the O-ring attached properly to the opening on the Case? • Is there any dirt or foreign matter on the O-ring or the O-ring contact surface on the front lid? • Is the waterproof function maintenance performed? (For details of the maintenance, refer to “Maintaining the waterproof function” (P. 23) of this manual.) CAUTION: • If the silica gel bag is caught when the Case is sealed, water leakage will occur. • Once silica gel has been used, the moisture absorption performance will be impaired. Always replace the silica gel when the Case is opened and closed. • Clean the surface of the dials of the Case and the camera. The dials may slip if there is grease or foreign matter on them. 2 3 PT-EP05L_06L_EN.Book Page 15 Friday, July 15, 2011 10:30 AM
Page: 17
EN 16 En Seal the Case 1 Close the Case gently while aligning the mounting projection of the rear lid and groove of the open/close dial. 2 Turn the open/close dial counter clockwise. • The Case is sealed. Attach the diffuser • Do not cap to optical fiber cable insertion slot. Check the operation of the loaded camera After sealing the Case, check that the camera operations normally. • Push the ON/OFF button on the Case and confirm that the camera turns ON/OFF. • Turn the mode dial knob on the Case and confirm that the camera mode switches properly. • Press the shutter lever on the Case and confirm that the camera shutter releases. • Operate the zoom dial on the Case and confirm that the camera’s lens is controlled. • Operate other control buttons on the Case and confirm that the camera functions properly as intended. • Push the ON/OFF button of the light and confirm that the light turns ON/OFF. CAUTION: • If the open/close dial is not fully turned, the Case will not be sealed. This will cause water leakage. • Close the rear lid of the Case so that the lens cap or LCD hood strap is not caught. If it is caught, water leakage may be caused. Close PT-EP05L_06L_EN.Book Page 16 Friday, July 15, 2011 10:30 AM
Page: 18
EN 17 En Water leakage test The final test after loading the camera is explained below. Always perform this test. It can be performed easily in a water tank or a bathtub. The required time is about five minutes. Confirm the operation of the different buttons. • At first, immerse the Case for only three seconds and check that no water drop etc. to inside of the Case. • Next, immerse the Case for 30 seconds and check that no water drop etc. to inside of the Case. • Then, immerse the Case for three minutes, operate all buttons and levers, and check the following: - check that no water has accumulated inside of the Case. - check that the Case is not fogged. - check that no water has entered inside of the Case. • If inside of the Case is fogged or there is a water drop, do the maintenance of the O-ring and perform the water leakage test again. PT-EP05L_06L_EN.Book Page 17 Friday, July 15, 2011 10:30 AM
Page: 19
EN 18 En 4. Connecting the underwater flash Connecting the underwater optical fiber cable To connect the UFL-2 underwater flash (optional) to the Case using an underwater optical fiber cable (optional: PTCB-E02), follow the procedures below. Setting of the digital camera Set the RC mode of the camera to ON so that the camera's built-in flash is activated. In case of UFL-2, turn the RC mode to ON. For details, refer to the instruction manual of UFL-2. In case of UFL-1, plug the optical fiber cable in the same way. Turn the RC mode of the camera to OFF. Connecting the underwater optical fiber cable 1 Put the underwater optical fiber cable plug into the optical fiber cable insertion slot. Insert firmly until it stops next to the flash window cover. 2 Put the cap to the optical fiber cable insertion slot when not in use. PT-EP05L_06L_EN02.fm Page 18 Wednesday, July 20, 2011 12:27 PM
Page: 20
EN 19 En 5. Installing the underweater conversion lens Attaching the conversion lens. The underwater macro conversion lens PTMC-01 (optional) and underwater wide conversion lens PTWC-01 (optional) are supported. Vignetting in the four corners may occur when using the underwater wide conversion lens (PTWC-01) on land. Also, the camera built-in flash cannot be used with the underwater wide conversion lens. PT-EP05L_06L_EN.Book Page 19 Friday, July 15, 2011 10:30 AM
Page: 21
EN 20 En 6. Taking pictures under water Select the shooting modes For E-PL3 Assign the underwater mode to an Fn button to easily switch to that mode. Select [ / ] in [Button Function] in [ ] of [ ] in [MENU], then press the OK button. * [ menu display] of [ ] in [MENU] must be set to ON. In case of E-PM1, assign to the ((REC) button or Cross-cursor button T. For details, refer to the instruction manual of the digital camera. Underwater shooting modes „ Underwater Wide-Angle Suitable for shooting a scene that extends across a wide range such as a school of fish swimming through the water. Background blues are vividly reproduced. „ Underwater Macro Suitable for close-up shooting of small fish and other underwater creatures. Natural colors of the underwater are accurately reproduced. Note: • Press the Fn button to switch between Underwater Wide-Angle and Underwater Macro modes. • Turn the mode dial knob or hold down the Fn button to exit the underwater mode. Press the Fn button again to return to the underwater mode. • However, in SCN, iAUTO and movie modes, pressing the Fn button will not set the camera in underwater mode. PT-EP05L_06L_EN.Book Page 20 Friday, July 15, 2011 10:30 AM
Page: 22
EN 21 En 7. Handling after shooting Wipe off any waterdrop After underwater shooting, remove any water drop from the case. Use pressurized air or a soft, lint-free cloth to carefully wipe away any moisture from the hinge between the front and rear lids, the shutter lever and the open/close dial. Unload the digital camera and batteries Open the Case carefully and remove the digital camera and light batteries. Wash the Case with pure water After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time (30 minutes to 1 hour) in pure water to remove any salt. CAUTION: Water left between the front and rear lids can get inside the Case once it is opened. Please dry these areas carefully. CAUTION: • When opening the Case, make sure no water from outside (e.g. drops from your hair or the diving suit) gets inside the Case and/or on the camera. • Before opening the case, ensure that your hands or gloves are completely clean (free of sand, loose fibers, etc.). • Never open the Case in areas where water could splash or spray or where sand or dust could be blown in the air. When this cannot be avoided, for example if the battery or memory card needs to be changed, the Case and camera should be protected from the wind or spray with a plastic sheet or similar object. • Never touch the digital camera and/or battery when your hands are wet with sea water. CAUTION: • Water leakage may occur when a high water pressure is applied partially. Before washing the Case with water, remove the digital camera from it. • Operate the shutter lever and each buttons of this product in pure water to remove salt adhering to the shaft. Do not disassemble for cleaning. • Letting salt dry on the Case may impair the function. Always wash off any salt after use. PT-EP05L_06L_EN.Book Page 21 Friday, July 15, 2011 10:30 AM
Page: 23
EN 22 En Dry the Case After washing with pure water, use a lint-free soft cloth without any salt on it to wipe off any water drop and dry the Case completely at a well ventilated location in the shade. CAUTION: Do not use hot air from a hair drier or the like for drying and do not expose the Case to direct sunlight, as this may accelerate deterioration and deformation of the Case and deterioration of the O-ring, leading to leakage of water. When wiping the Case, take care not to cause scratches. PT-EP05L_06L_EN.Book Page 22 Friday, July 15, 2011 10:30 AM
Page: 24
EN 23 En 8. Maintaining the waterproof function The O-ring is a consumable product. Before each use, perform proper maintenance. Always be sure to perform the O-ring maintenance operation as described below. Neglecting this maintenance may become the cause of water leakage. Perform at the location without sand or dust, after washing and drying your hands. Remove the O-ring Open the Case and remove the O-ring. Procedure 1 Insert the O-ring remover into the gap between the O-ring and O-ring groove wall. 2 Bring the tip of the inserted O-ring remover below the O-ring. (Be careful not to damage the groove with the tip of the O-ring remover.) 3 Lift the O-ring, pinch it with your fingertips and pull it out of the Case. Remove any sand, dirt, etc. After visually checking that dirt has been removed from the O-ring, check for attached sand and other foreign matter, as well as for damage and cracks by squeezing the entire circumference of the O-ring lightly with your fingertips. Remove attached foreign matter from the O-ring groove with a clean cloth or a cotton swab. Also remove any sand or dirt attached to any part of the Case that comes into contact with the O-ring. Install the O-ring Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into the groove. At this time, confirm that the O-ring does not stick out from the groove. When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick not only to the O-ring, but also to the contact surface (front cover). Even a single hair or a single grain of sand may cause water leakage. Please check with special care. CAUTION: • When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. • When the O-ring is checked with the fingertips, take care not to stretch the O-ring. • Never use alcohol, thinner, benzene or similar solvents or chemicals detergents to clean the O-ring. When such chemicals are used, it is likely that the O-ring will be damaged or that its deterioration will be accelerated. PT-EP05L_06L_EN.Book Page 23 Friday, July 15, 2011 10:30 AM
Page: 25
EN 24 En Applying grease to the O-ring Replace consumable products • The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new piece at least once a year. • Deterioration of the O-ring is accelerated by the usage conditions and the storage conditions. Replace the O-ring even before a year has passed if it shows signs of damage, cracking or loss of elasticity. 1 Apply only Olympus exclusive grease to O-ring. Make sure that your fingers and the O-ring are free of dirt, and squeeze about 5 mm of grease onto a finger. (5 mm is the most appropriate amount.) 2 Spread the grease onto the entire circumference of the O-ring. Spread the grease onto the entire circumference of the O-ring using 3 fingers. Be careful not to use excessive force as this may stretch the O-ring. 3 Check that the O-ring is free of scratches or unevenness. After spreading the grease, check visually and by touch that the O-ring is not scratched and that its surface is flat. If it is damaged in any way, replace it with a brand-new O-ring. CAUTION: • Always perform maintenance of the waterproof function even when the Case has been opened every shooting. Neglecting this maintenance may become the cause of water leakage. • When the Case is not to be used for a long time, remove the O-ring from the groove to prevent deformation of the O-ring, apply a thin coat of silicone grease, and store it in a clean plastic bag or the like. Examples of foreign matter sticking to the O-ring Hair Fibers Grains of sand CAUTION: • Use genuine Olympus silicone grease, silica gel and O-ring. • Do not try to replace the O-ring by yourself. • We recommend to perform the check periodically. PT-EP05L_06L_EN.Book Page 24 Friday, July 15, 2011 10:30 AM
Page: 26
EN 25 En 9. Appendix Specifications * We reserve the right to change the external appearance and the specifications without notice. Supplied accessories for PT-EP05L/06L O-ring: POL-EP03 Silicone grease: PSOLG-2 Silica gel: SILCA-5S LCD hood: PFUD-EP05 Body cap: PBC-EP01 Diffuser: PTDP-EP05 Antireflective ring: POSR-EP05 Flash window cover: PFC-EP05 O-ring remover: PTAC-05 Optional accessories Silicone grease: PSOLG-3 Underwater optical fiber cable: PTCB-E02 Bracket: PTBK-E01, PTBK-E02 Short arm: PTSA-02/PTSA-03 Underwater flash: UFL-2, UFL-1 Underwater macro conversion lens: PTMC-01 Underwater wide conversion lens: PTWC-01 Zoom gear: PPZR-EP02 * When use combining PTBK-E01 and the Case, the dedicated washers are necessary in the screw part. If you have PTBK-E01 to which dedicated washers are not bundled, please contact to customer support center. Supplied accessories can be purchased. Products of other model types than those describing above cannot be used. Underwater case PT-EP05L PT-EP06L Supported camera E-PL3 E-PM1 Pressure resistance Depth of down to 45 m (147 feet) Main materials Main body: Polycarbonate O-ring: Silicone rubber Light batteries 2 AAA batteries (Alkaline / NiMH) Lighting time Approx. 4 hours in continuous use (when using alkaline batteries) Dimensions Width 175 mm × height 149 mm × depth 156 mm Width 175 mm × height 149 mm × depth 152 mm Weight Approx. 1,110 g (camera and accessories not included) Weight under water Approx. –30 g (in the freshwater) (including camera, lens, zoom gear, antirefletive ring, batteries and media card) PT-EP05L_06L_EN.Book Page 25 Friday, July 15, 2011 10:30 AM
Page: 27
PT-EP05L_06L_EN.Book Page 26 Friday, July 15, 2011 10:30 AM

Question & answers

Have a question about the Olympus PT-EP05L but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Olympus PT-EP05L. Please make sure that you describe your difficulty with the Olympus PT-EP05L as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Olympus PT-EP05L

Name
Email
Reaction

View a manual of the Olympus PT-EP05L below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Olympus
  • Product: Not categorized
  • Model/name: PT-EP05L
  • Filetype: PDF
  • Available languages: English, German, Dutch