Olympus P-S100 manual

User manual for the Olympus P-S100 in English. This PDF manual has 132 pages.

Page: 1
ENGLISH FRANÇAIS ESPAÑOL USER’S MANUAL MANUAL DE L’UTILISATEUR MANUAL DEL USUARIO Digital Photo Printer Imprimate photo numerique Impresora de fotografia digital P-S100 00Doya_E COV.fm Page 1 Thursday, November 11, 2004 10:52 AM
Page: 2
Introduction EN-2 Introduction Read this manual carefully prior to use to ensure correct use of this product. For customers in North and South America For customers in USA Declaration of Conformity Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: FCC Notice • Radio and Television Interference Change or modifications not expressly approved by the manufacturer may void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Adjust or relocate the receiving antenna. - Increase the distance between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult your dealer or an experienced radio/TV technician for help. Only the OLYMPUS-supplied cables should be used to connect this product to other products. WARNING: The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with device. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Any unauthorized changes or modifications to this equipment would void the user’s authority to operate. For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Product Name : Digital Photo Printer Model Number : P-S100 Trade Name : OLYMPUS Responsible Party : Address : Two Corporate Center Drive, PO Box 9058, Melville, NY 11747-9058 U.S.A. Telephone Number : 1-631-844-5000 (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Doya_E.book Page 2 Thursday, November 11, 2004 10:50 AM
Page: 3
Introduction EN-3 For customers in Europe “CE” mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. “CE” mark printers are intended for sales in Europe. Trademarks • Q and are trademarks of OLYMPUS CORPORATION. • OLYMPUS Master is a trademark of OLYMPUS CORPORATION. • Windows is registered trademark of Microsoft Corporation. • Macintosh and Apple are trademarks of Apple Computer, Inc. • All brand names and product names contained in this manual are trademarks or registered trademarks of their owners. Doya_E.book Page 3 Thursday, November 11, 2004 10:50 AM
Page: 4
Features EN-4 Features QDock&Done feature support By connecting OLYMPUS Dock&Done products with this printer using a Dock&Done cable, you can perform a sequence of operations, such as photographing, printing, saving pictures, and charging the camera battery automatically. Direct print This printer conforms to PictBridge, which is a standard common to digital cameras and printers. If you connect this printer to a PictBridge-compatible digital camera using a USB cable, you can print pictures stored in the digital camera directly from the camera. Variety of print This printer supports various printing options, including printing multiple instances of the same picture on one sheet (multi-printing), printing multiple different pictures on one sheet (index printing), printing pictures with date and time included, and printing with edged or not edged pictures. Printing from a PC You can connect this printer to a PC using a USB cable to print pictures stored on a PC. Printing on high-quality overcoat paper Printing on high-quality overcoat paper ensures long lasting, durable prints of high quality. This is especially useful for printing photographs you can treasure for years to come. Paper-in tray (includes 50 sheets of paper) The paper-in tray comes with paper already inside, so you don't need to worry about getting fingerprints on the paper. It is also very easy to insert the tray into the printer. Once the paper is gone, you can use the container to store your printed photographs. Printing 50 sheets continuously You can print up to a maximum of 50 sheets from one paper-in tray. Note Some printer functions may be restricted depending on the digital camera connected. Doya_E.book Page 4 Thursday, November 11, 2004 10:50 AM
Page: 5
Operating procedure EN-5 Operating procedure Use the following flowchart for reference: Plugging in to an outlet and turning the printer on/off (gpage 18) Loading the ribbon cartridge (gpage 19) Loading the paper and replacing the ribbon cartridge (gpage 32) Loading paper (gpage 22) QDock&Done Digital camera PC Using the printer in QDock&Done mode (gQUICK START GUIDE) Connecting a digital camera to the printer (gpage 25) Installing the printer driver (gpage 27) Using a digital camera to print (gpage 26) Connecting a PC to the printer (gpage 28) Printing pictures (gpage 28) Doya_E.book Page 5 Thursday, November 11, 2004 10:50 AM
Page: 6
Table of contents EN-6 Table of contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operating procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Read this first Safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Checking the contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Parts and controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Preparation Plugging in to an outlet and turning the printer on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Loading the ribbon cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 About the paper-in tray and the ribbon cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Setting the ribbon cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Removing the ribbon cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Loading paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Setting the paper-in tray into the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Printing Printing pictures from a digital camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 About QDock&Done-compatible digital cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 About PictBridge-compatible digital cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Connecting a digital camera to the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Using a digital camera to print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Printing pictures from a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Installing the printer driver (during initial setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Connecting a PC to the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Printing pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Doya_E.book Page 6 Thursday, November 11, 2004 10:50 AM
Page: 7
Table of contents EN-7 Additional information Loading the paper and replacing the ribbon cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 If paper runs out during printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 If the ribbon runs out during printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 About used paper-in trays and ribbon cartridges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Error signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 When paper is jammed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 If the ribbon cartridge is removed during printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 If the paper-in tray is removed during printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 About the Paper-in Tray/Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Before you contact us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Doya_E.book Page 7 Thursday, November 11, 2004 10:50 AM
Page: 8
Safety regulations Read this first EN-8 Read this first Safety regulations Various icons are used in this manual to indicate correct product usage and to help prevent property damage and injury to customers and others. The meanings of these icons are described below. Precautionary notations are indicated by the following symbols. Icon Description WARNING Failure to follow instructions indicated by this icon may lead to serious injury or death. CAUTION Failure to follow instructions indicated by this icon may lead to injury or property damage. Icon Description Do not perform this action. You are strongly encouraged to perform this action. Unplug the device from the power source. Do not disassemble. Avoid contact with water and other liquids. Do not touch if your hands are wet. Doya_E.book Page 8 Thursday, November 11, 2004 10:50 AM
Page: 9
Safety regulations Read this first EN-9 WARNING If this device acts abnormally, unplug it Do not use the printer if it emits smoke, unusual smells, strange sounds, or becomes unusually warm. Use under these conditions may cause fire or electric shock. Turn off and unplug the printer. Then contact an authorized Olympus service center. Should any liquid or foreign objects get into the printer, unplug the power cord Do not allow any liquids, metals, or flammable objects to get into the printer. This may cause fire or electric shock. Turn off and unplug the printer. Then contact an authorized Olympus service center. If the printer cabinet is damaged, unplug the power cord Do not use this device if the cabinet (body) is damaged. Use in this condition may cause fire or electric shock. Turn off and unplug the printer. Then contact an authorized Olympus service center. If the power cord is damaged, unplug it Do not use a damaged power cord. Use in this condition may cause fire or electric shock. Turn the printer off, and unplug the power cord being careful not to touch any exposed wires. Then contact an authorized Olympus service center. Do not damage the power cord Do not damage or modify the power cord. A damaged power cord may result in fire or electric shock. To prevent damage, do not bend the cord excessively or pull on the cord when unplugging. Take care no heavy objects are placed on or roll over the cord. If the power cord is damaged, contact an authorized Olympus service center. Doya_E.book Page 9 Thursday, November 11, 2004 10:50 AM
Page: 10
Safety regulations Read this first EN-10 WARNING Do not disassemble or modify the printer The printer has both hot and high voltage parts on the inside. Touching these parts may result in burns, electric shock, and/or damage to the printer. Never attempt to disassemble or modify the printer as this may lead to electric shock or printer malfunction. For service or repair, contact an authorized Olympus service center. Do not allow liquids near the printer If liquid gets into the printer, it may result in fire or electric shock. Do not place heavy objects on the printer Heavy objects may damage the printer cabinet, resulting in fire or electric shock. Damage may also result from the printer being dropped or falling. Do not install the printer in the following places To prevent fire, electric shock, and printer malfunction, do not install the printer in the following places: • Dusty, humid, or oily places Should any dust or liquid get into the printer, it may result in fire or electric shock. • Extremely hot places Do not expose the printer to direct sunlight, such as inside a car or near a window or extremely high temperatures, such as near a heater. Doing so may damage the printer cabinet, resulting in fire or electric shock. Use the printer in an environment with an ambient temperature between 10 to 35°C (50 to 95°F) and humidity of 30 to 80%. Do not use the printer in the following places • Unstable or inclined surfaces. • Outdoors (particularly on beaches, etc.), or places that expose the printer to excessive dust or debris. • Places subject to rain, dripping, or enclosed places where condensation could occur such as inside a plastic bag. Doya_E.book Page 10 Thursday, November 11, 2004 10:50 AM
Page: 11
Safety regulations Read this first EN-11 WARNING Do not use the printer with an AC adapter or power cord other than that specified/provided Do not use the provided AC adapter or power cord with any other devices Provide correct voltage Incorrect voltage may damage printer parts. Use with incorrect voltage may cause fire or electric shock. Connect the power cord correctly/safely If the power cord is plugged in loosely, it may cause a fire or electric shock. Push the plug all the way into the outlet. Make sure that excessive dust and debris do not accumulate on the power cord Dust and debris may conduct electricity, which can cause fire and electric shock. If excessive dust and debris accumulate on the cord, unplug the cord and clean it. Always unplug the power cord during an electrical storm The induced electricity from storms may cause fire, electric shock, or printer malfunction. Do not hold the power plug with wet hands Doing so may result in fire, electric shock, or printer malfunction. Be sure your hands are dry before handling. Plug the printer directly into an outlet Avoid overloading outlets with use of extensions and adapters, etc. Do not move the printer when the power cord is taut Moving the printer when the power cord is taut may damage the cord. Using the printer when damaged may cause fire or electric shock. When moving the printer, unplug and bundle the power cord. Doya_E.book Page 11 Thursday, November 11, 2004 10:50 AM
Page: 12
Safety regulations Read this first EN-12 CAUTION Ensure there is adequate ventilation around the printer Do not put the printer where there is poor ventilation, or on a soft surface such as a rug or bed. Do not put the printer on an unstable surface Do not put the printer on an unstable surface such as a shaky table. Injury may result from the printer being dropped or falling. This could also damage the printer or cause the printer to malfunction. Do not touch the non-user-serviceable parts inside the printer Doing so may cause injury or burns. This applies especially to children and those unfamiliar with the printer. Do not unplug the printer by jerking or pulling on the power cord To unplug the power cord, hold it by the plug. Pulling on the cord may damage it, possibly resulting in fire or electric shock. Unplug the printer for servicing Always unplug the printer before servicing or performing maintenance. Unplug the printer if it will not be used for an extended period of time Unplug the printer if it will not be used for an extended period of time, such as while you are away on a long trip. Otherwise, deteriorated insulation or current leakage may cause fire or electric shock. Doya_E.book Page 12 Thursday, November 11, 2004 10:50 AM
Page: 13
Precautions Read this first EN-13 Precautions When condensation occurs Condensation is the occurrence of water droplets forming on surfaces, and may occur under the following conditions: • The room where the printer is located is heated quickly. • Cool air from an air-conditioner blows directly onto the printer. • The printer is moved from a low-temperature location to a high-temperature location. When condensation occurs, print paper may become moist. This may cause printing quality deterioration or paper jams. If condensation has occurred or is expected to occur, refrain from using the printer until condensation is no longer present or likely to occur. When cleaning the printer, do not use thinner, benzine, or any other solvent If the printer comes into contact with insecticide or is wiped with thinner or benzine, the finish may deteriorate or peel. To clean the printer exterior, wipe with a soft cloth. If stains are persistent, dampen the soft cloth with water or a diluted mild detergent, wring it carefully, and then wipe the exterior with the cloth. Do not allow the printer to remain in contact with rubber or plastic products for an extended period of time Deterioration and discoloration may occur if the device remains in contact with rubber or plastic products for an extended period of time. Operate the printer at least once every six months If the printer is not used for a long period of time, it may malfunction. Run the printer at least once every six months. When lifting or transporting the printer When lifting or transporting the printer, grasp it with both hands. When transporting the printer When transporting the printer, place it in the original box with the original packing material. If the original packing material is not available, pack the printer with enough cushion to absorb any impacts during transportation. Doya_E.book Page 13 Thursday, November 11, 2004 10:50 AM
Page: 14
Precautions Read this first EN-14 Appropriate installation locations Install the printer on a flat stable surface. Allow for suitable clearance around the printer. Notes • A space of at least 100 mm (4") is required behind the printer because paper is partially ejected from the rear of the printer during printing. • The cables on the rear of the printer should be directed straight out or away from the printer so they won't interfere with paper during printing. at least 100 mm (4") Doya_E.book Page 14 Thursday, November 11, 2004 10:50 AM
Page: 15
Checking the contents Read this first EN-15 Checking the contents Check for the following contents when unpacking the printer. If one or more accessories are missing, contact an authorized Olympus service center. AC adapter (1) Power cord (1)*1 Paper-in Tray/Ribbon Cartridge • USER’S MANUAL (this book) (1) • QUICK START GUIDE (1) • Registration card (1)*2 • Warranty card (1) P-S100 software CD-ROM (printer driver) (1) *1 The shape of the plug differs from country to country. *2 Not supplied in some areas. Contents of the Paper-in Tray/Ribbon Cartridge Ribbon cartridge (good for 50 sheets of paper) Paper-in tray (includes 50 sheets of paper) Cap Index Sticker (2) • Used paper-in trays can be used as container boxes for photographs. • Index sticker and cap can be used with used paper-in trays. Doya_E.book Page 15 Thursday, November 11, 2004 10:50 AM
Page: 16
Parts and controls Read this first EN-16 Parts and controls Front Rear PAPE R RIBB ON AC CE SS C E F D B A G H I J K PA PE R RIB BO N AC CE SS O N M Q P L Doya_E.book Page 16 Thursday, November 11, 2004 10:50 AM
Page: 17
Parts and controls Read this first EN-17 Number Name Function A POWER button Turns the power on/off (gpage 18). B POWER indicator Indicates the power is on/off (gpage 18). C PAPER indicator Blinks when a paper error occurs (gpage 33). D RIBBON indicator Blinks when a ribbon cartridge error occurs (gpage 33). E ACCESS indicator Indicates the printer status (gpage 33). F Paper-in tray door Open this door when you install or replace the paper-in tray (gpage 22). G Paper-in tray door tab Use this tab when opening the paper-in tray door (gpage 22). H Ribbon cartridge door Open this door when you install or replace the ribbon cartridge (gpage 19). I Ribbon cartridge door tab Use this tab when opening the ribbon cartridge door (gpage 19). J Tab Pull this tab up when taking out the ribbon cartridge (gpage 20). K Ribbon cartridge slot The ribbon cartridge is inserted into this slot (gpage 20). L Paper path During printing, paper is partially ejected (gpage 14). M PictBridge connector USB cable connector for a PictBridge-compatible digital camera (gpage 25). N USB connector USB cable connector for a PC (gpage 28). O QDock&Done storage connector Cable connector for a dedicated Dock&Done device (gQUICK START GUIDE). P Shutter Covers connectors that are not in use (gQUICK START GUIDE). Q DC-IN jack Connect the AC adapter to this port (gpage 18). Doya_E.book Page 17 Thursday, November 11, 2004 10:50 AM
Page: 18
Plugging in to an outlet and turning the printer on/off Preparation EN-18 Preparation Plugging in to an outlet and turning the printer on/ off 1 Plug the power cord into the AC adapter. 2 Plug the power plug into a wall outlet, and then plug the DC plug into the DC-IN jack. 3 Press the POWER button. The POWER indicator turns on. Press the POWER button. The POWER indicator turns off. Note If the DC plug is accidentally unplugged from the printer during printing, turn the printer off, plug the DC plug into the DC-IN jack, and then turn the printer on again. Leaving the printer unplugged may cause it to malfunction. To turn off the printer DC plug Insert the power cord plug into the wall outlet. Doya_E.book Page 18 Thursday, November 11, 2004 10:50 AM
Page: 19
Loading the ribbon cartridge Preparation EN-19 Loading the ribbon cartridge About the paper-in tray and the ribbon cartridge For printing, a paper-in tray and a ribbon cartridge are required (both supplied, as well as commercially available as replacements). For details, refer to “About the Paper-in Tray/Ribbon Cartridge” (gpage 38). Setting the ribbon cartridge 1 Open the ribbon cartridge door. 2 Remove slack from the ribbon. If the ribbon cartridge has been used before, take in any ribbon slack before loading. Notes • Do not mix ribbon cartridges and paper-in trays that are packaged together. • Do not use paper that has already been printed on or ejected. Turn the roll in the direction indicated by the arrow while holding the roller in place. Doya_E.book Page 19 Thursday, November 11, 2004 10:50 AM
Page: 20
Loading the ribbon cartridge Preparation EN-20 3 Insert the ribbon cartridge into the printer following the direction of the arrow, and then close the ribbon cartridge door completely. • Push the cartridge in until it clicks. • If the ribbon cartridge door cannot be closed completely, take out the ribbon cartridge and then reinsert it. Removing the ribbon cartridge Open the ribbon cartridge door, and raise the tab. When the ribbon cartridge comes free, take it out. Note When opening the ribbon cartridge door, be careful not to touch the inside of the ribbon cartridge slot as it may be very hot. Doya_E.book Page 20 Thursday, November 11, 2004 10:50 AM
Page: 21
Loading the ribbon cartridge Preparation EN-21 • Combinations of paper-in tray and ribbon cartridges are available in two types: one is for 100 × 148 mm (4×6) paper and the other is for 89 × 127 mm (3.5" × 5") paper. Use the appropriate ribbon cartridge for each size paper. • When setting a ribbon cartridge aside, keep it upright to protect it from dust. Do not touch the ribbon or leave a ribbon cartridge in a dusty environment. Fingerprints or dust on a ribbon may cause printing quality to deteriorate. • If the ribbon has torn, replace the ribbon cartridge with a new one. Note on ribbon cartridge storage Store ribbon cartridges in a place that is free from high temperature, humidity, dust, and direct sunlight. Ribbon cartridge for 100 × 148 mm (4 × 6) printing Ribbon cartridge for 89 × 127 mm (3.5" × 5") printing This is not available in certain local areas. 100 × 148 89 × 127 Doya_E.book Page 21 Thursday, November 11, 2004 10:50 AM
Page: 22
Loading paper Preparation EN-22 Loading paper Setting the paper-in tray into the printer 1 Open the paper-in tray door. When closing the paper-in tray door, push the paper-in tray door tab in as you close the door until it clicks into place and locks. 2 Remove the protective sheet. 3 Insert the paper-in tray all the way. • Push the paper-in tray until it clicks into place. • To remove the paper-in tray, pull it out holding both sides. Protective sheet Doya_E.book Page 22 Thursday, November 11, 2004 10:50 AM
Page: 23
Loading paper Preparation EN-23 Tip Printed paper is ejected onto the top of the paper-in tray. Doya_E.book Page 23 Thursday, November 11, 2004 10:50 AM
Page: 24
Printing pictures from a digital camera Printing EN-24 Printing Printing pictures from a digital camera About QDock&Done-compatible digital cameras You can print pictures more easily by connecting your Dock&Done-compatible digital camera to the printer. For details on connections, refer to the supplied “QUICK START GUIDE.” About PictBridge-compatible digital cameras You can print pictures directly by connecting your PictBridge-compatible digital camera to the printer. You can specify the pictures to be printed and the number of prints by following the instructions displayed on the LCD screen of the camera while it is connected to the printer. The printing procedure varies from one digital camera to another. Refer to the manual supplied with your digital camera. You can print pictures based on the print order you entered in Digital Print Order Format (DPOF). For details on PictBridge-compatible digital cameras, visit the OLYMPUS website. About DPOF (Digital Print Order Format) You can record the following print order on a card. • Selected images for printing taken by digital camera. • Number of prints. • Date and time. The information is saved on the card in DPOF format. You can take the card to a photo developer service supporting DPOF and ask them to print the images based on the print order recorded on the card. Tips In PictBridge mode, the initial printer settings are as follows. • Paper size automatically selected according to the paper loaded in the printer. • One-sheet printing selected. • Not edged printing selected. • Date printing disabled. • File name printing disabled. Notes • Images not taken by a digital camera must be printed by a PC. • The maximum number of digital camera images you can print (both index and regular size) is 200 at one time. If you set more, only the first 200 are printed. • While the printer is cooling off, if you cancel the printing, the last image queued will be printed. Doya_E.book Page 24 Thursday, November 11, 2004 10:50 AM
Page: 25
Printing pictures from a digital camera Printing EN-25 Connecting a digital camera to the printer The procedure below assumes that you are connecting a PictBridge-compatible digital camera. Use the USB cable supplied with the digital camera to connect. Refer to the “QUICK START GUIDE” for Dock&Done connection. 1 Turn on the printer. For details, refer to “Plugging in to an outlet and turning the printer on/off” (gpage 18). 2 Plug one end of the USB cable into the USB connector on the digital camera, and then plug the other end into the PictBridge connector on the rear of the printer. 3 Turn on the digital camera and prepare it for printing. The ACCESS indicator on the printer turns on for a few moments and then turns off. For details on how to use the digital camera, refer to the instruction manual supplied with the digital camera. Doya_E.book Page 25 Thursday, November 11, 2004 10:50 AM
Page: 26
Printing pictures from a digital camera Printing EN-26 Using a digital camera to print 1 Print the desired picture by following the instructions displayed on the digital camera screen. The ACCESS indicator on the printer blinks when printing is in progress. The indicator turns off when printing ends. For details on how to use the digital camera, refer to the manual supplied with the digital camera. 2 When printing is complete, turn off the printer and digital camera, and then disconnect the USB cable. Notes • Printing will stop if you unplug the power plug during printing. The paper should be automatically ejected when you turn on the printer again. If it is not, refer to “When paper is jammed” (gpage 36). • Do not open the ribbon cartridge door or remove the paper-in tray during printing. • Do not move the printer during printing. • Do not turn off the printer or digital camera, or disconnect the AC adapter during printing. If you inadvertently turn off the printer or disconnect the AC adapter, turn on the printer and then retry printing. If you leave the printer as is, a failure might occur. • Do not unplug the USB cable during printing. • Wait at least 10 seconds after unplugging the USB cable before plugging it back in, or vice versa. Sample digital camera screen Doya_E.book Page 26 Thursday, November 11, 2004 10:50 AM
Page: 27
Printing pictures from a PC Printing EN-27 Printing pictures from a PC You can use OLYMPUS Master or CAMEDIA Master software, which comes with an OLYMPUS digital camera, or most other common pictures processing applications to print pictures stored in a PC. Installing the printer driver (during initial setup) Supported Windows operating systems: Windows 98SE/Me/2000/XP Supported Macintosh operating systems: Mac OS X v10.3 and later 1 Start up your PC, and then insert the software CD-ROM supplied with the printer into the CD-ROM drive. If you are using Macintosh, double click the [Installer] icon displayed on the desktop to begin installation. 2 Install the printer driver by following the instructions displayed on the screen. For details, refer to the instruction manual supplied with the PC. Note Images that were not taken by a digital camera must be printed by a PC. Note Before connecting the printer to a PC, you must install the printer driver. Tip For details, refer to the Installation Guide on the software CD. Tip If your PC with a USB connector is one of the following, operation is not guaranteed. – The operating system is Windows 95/NT 4.0/98. – The operating system is Windows 98/98SE upgraded from Windows 95. – Mac OS 8.6-9.2. – Your PC’s USB connector was added using an extension card or similar means. – Your PC was shipped without a pre-installed OS or was home-built. Doya_E.book Page 27 Thursday, November 11, 2004 10:50 AM
Page: 28
Printing pictures from a PC Printing EN-28 Connecting a PC to the printer Use a commercially available USB cable (A-B type, less than 3m (9.8 ft.)). 1 Plug one end of the USB cable into the USB port on the PC, and then plug the other end into the USB connector on the rear of the printer. 2 Turn on the printer. Printing pictures 1 In your application, display and select the pictures to be printed. 2 On the print screen, select [P-S100] from the available printer list. 3 On the print setting screen, check the paper size and other properties, and then start printing. For details, refer to “Setting the print properties” (gpage 29). Notes • When this printer is connected both to a PC and a PictBridge-compatible digital camera, it assigns higher priority to the digital camera. Disconnect the digital camera. • This printer's performance is not guaranteed in a network environment. • This printer's performance is not guaranteed when connected to a USB hub. Note [Print] operations and printer selection vary depending on the application. Refer to the manual supplied with your application. Notes • Printing will stop if you unplug the power cord during printing. The paper should be automatically ejected when you turn on the printer again. If it is not, refer to “When paper is jammed” (gpage 36). • Do not open the ribbon cartridge door or remove the paper-in tray during printing. • Do not move the printer during printing. • Do not turn off the printer or PC, or disconnect the AC adapter during printing. If you inadvertently turn off the printer or disconnect the AC adapter, turn on the printer and then try printing again. If you leave the printer as is, a failure might occur. Doya_E.book Page 28 Thursday, November 11, 2004 10:50 AM
Page: 29
Printing pictures from a PC Printing EN-29 Setting the print properties If you are using Windows: Select [Printing Preferences] from the File menu. On the [OLYMPUS P-S100 Printing Preferences] screen, use the [Paper] and [Color Adjustment] tabs to change the paper size, number of copies, and to make adjustments to the color settings. Paper setup screen: The following items can be set. Color Adjustment screen: The following items can be set. Item Contents Paper Size Select 4 × 6 (100 × 148 mm) or 3.5" × 5" (89 × 127 mm). Copy Count Select from 1 to 50. Orientation Select [Landscape] or [Portrait]. Print Area Select [Not Edged] or [Edged]. Enlarge/Reduce Set the print size from 25 to 400%. Sharpness Select the [Sharpness] among [OFF], [Soft], [Normal], or [Hard]. Item Contents Tone Adjust the [Tone] from -5 (Lightest) to +5 (Strongest) among the [Red], [Green], and [Blue]. Saturation Set the [Saturation] from 0 to +10 (Strongest). Brightness Set the [Brightness] from -5 (Darkest) to +5 (Brightest). Contrast Set the [Contrast] from -5 (Lightest) to +5 (Strongest). Paper setup screen Color Adjustment screen Doya_E.book Page 29 Thursday, November 11, 2004 10:50 AM
Page: 30
Printing pictures from a PC Printing EN-30 If you are using Macintosh: Select [Page Setup] and [Print] from the File menu to change the paper size, number of copies, and to make adjustments to the color settings. Page Setup screen: The following items can be set. Note The screens are those in Mac OS X v10.3. They may differ depending on the operation system. Item Contents Settings Select [Page Attributes]. Format for Select [P-S100]. Paper Size Select one of the following paper sizes/styles. • Edged 4 × 6 (100 × 148 mm). • Not Edged 4 × 6 (100 × 148 mm). • Edged 3.5" × 5" (89 × 127 mm). • Not Edged 3.5" × 5" (89 × 127 mm). Orientation Select print orientation. Scale Enter the scale. Page Setup screen Doya_E.book Page 30 Thursday, November 11, 2004 10:50 AM
Page: 31
Printing pictures from a PC Printing EN-31 Print screen: The following items can be set. Item Contents Printer Select [P-S100]. Presets Select [Standard], then select [Printer Features]. From the [Feature Sets], select [Setting 1] or [Setting 2]. Setting 1 Saturation Set the [Saturation] from 0 to +10 (strongest). Brightness Set the [Brightness] from -5 (darkest) to +5 (brightest). Contrast Set the [Contrast] from -5 (lightest) to +5 (strongest). Sharpness Select the [Sharpness] among [OFF], [Soft], [Normal], or [Hard]. Setting 2 Tone Adjust the [Tone] from -5 (lightest) to +5 (strongest) from [Tone Red], [Tone Green], and [Tone Blue]. Sample: Print screen 1 Sample: Print screen 2 Doya_E.book Page 31 Thursday, November 11, 2004 10:50 AM
Page: 32
Loading the paper and replacing the ribbon cartridge Additional information EN-32 Additional information Loading the paper and replacing the ribbon cartridge If paper runs out during printing The PAPER indicator blinks slowly. Replace the paper-in tray. The remaining data is automatically printed. Under normal circumstances the ribbon will end at the same time as the paper runs out. Replace the ribbon cartridge with a new one. If the ribbon runs out during printing The RIBBON indicator blinks slowly. Wait until paper is ejected, and then replace the ribbon cartridge with a new one. When you close the ribbon cartridge door, the remaining data will be automatically printed. About used paper-in trays and ribbon cartridges • Used paper-in trays can be used as container boxes for photographs. • Paper-in trays and ribbon cartridges are made of plastic. When disposing, check local regulations. Index Sticker Cap Doya_E.book Page 32 Thursday, November 11, 2004 10:50 AM
Page: 33
Error signals Additional information EN-33 Error signals * This light goes off when the connection is complete. Indicator Indicator status Printer status Solution Page(s) POWER On Power ON – 18 Off Power OFF ACCESS On* Connected to a digital camera, or the printer is cooling off Wait for a while. Do not disconnect the digital camera or PC. – Blinking slowly Communicating Blinking very slowly Printing – – PAPER Blinking slowly Out of paper Replace the paper-in tray. 22, 32 RIBBON Blinking slowly End of ink ribbon Replace the ribbon cartridge with a new one. 19, 32 No ribbon cartridge is set Set a ribbon cartridge into the printer. 19 The paper and the ribbon cartridge are incompatible Use a ribbon cartridge for 100 × 148 mm (4 × 6) printing when printing on 100 × 148 mm (4 × 6) papers, and use a ribbon cartridge for 89 × 127 mm (3.5" × 5") printing when printing on 89 × 127 mm (3.5" × 5") papers. 21 ACCESS and PAPER Blinking together Paper jam Remove jammed paper. 36 ACCESS and RIBBON Blinking together Communication error Check whether the digital camera supports PictBridge. – Turn the printer off and on, then try printing again. If the error persists, contact an authorized Olympus service center. – ACCESS, RIBBON, and PAPER Blinking together Internal problem Contact an authorized Olympus service center. – Doya_E.book Page 33 Thursday, November 11, 2004 10:50 AM
Page: 34
Troubleshooting Additional information EN-34 Troubleshooting Before asking for repairs, check the printer using the following checklist. If the problem still occurs, contact an authorized Olympus service center. Problem Cause / status Solution Page(s) The power does not turn on. The AC adapter is not connected. Connect the AC adapter. 18 The ribbon cartridge cannot be removed. The power turns off during printing. Push the ribbon cartridge until it clicks. Turn on the printer again, and wait until the operation sound stops. – Printing a picture from a digital camera does not start soon. The printer takes a long time to open a TIFF file. The loading time varies depending on the image size. Wait until loading is complete. – – The size of a JPEG file is large. – Printing does not start. The paper-in tray or ribbon cartridge is not suitable for the paper size you are using. Use a ribbon cartridge and paper-in tray of the same size. 21, 38 The print size set on a digital camera or PC is different from the loaded Paper-in Tray/Ribbon Cartridge. Insert the same size paper and ribbon cartridge as selected on the digital camera or PC. No ribbon cartridge is set in the printer. Set a ribbon cartridge. 19 No paper in the paper-in tray. Replace the paper-in tray. 22 Paper is jammed in the paper ejection area. Remove the jammed paper. 36 The printer driver is not correctly installed on the PC. Install or re-install the printer driver on the PC correctly. 27 Indicators lights or blinks. – 33 Doya_E.book Page 34 Thursday, November 11, 2004 10:50 AM
Page: 35
Troubleshooting Additional information EN-35 Trimming specification is ignored although it is included in the print reservation information. The printer does not support trimming. – – Noise interferes with printed images. Pictures that were not taken with a digital camera were printed from a digital camera. Images that were not taken by a digital camera must be printed from a PC. 27 The printing interval has become longer. The printer is designed to prevent overheating by automatically prolonging the printing interval as printing proceeds continuously. This is not a malfunction. Be patient. – Problem Cause / status Solution Page(s) Doya_E.book Page 35 Thursday, November 11, 2004 10:50 AM
Page: 36
Troubleshooting Additional information EN-36 When paper is jammed When paper is jammed, the ACCESS and PAPER indicators blink and printing stops. Follow these steps to remove jammed paper. 1 Turn off the printer. 2 Remove the paper-in tray. 3 Turn on the printer again. The paper should be ejected automatically. • If the paper is automatically ejected, go to Step 8. • If the paper is not automatically ejected, turn off the printer and go to Step 4. 4 Check the inside of the paper-in tray door to see whether paper is visible at the rear. • If it is, go to Step 5. • If it is not, contact an authorized Olympus service center. 5 Open the ribbon cartridge door. Use a flathead screwdriver to turn the screw in the counterclockwise or clockwise direction. Notes • Do not pull the jammed paper too hard. The paper may tear inside the printer. • Jammed paper that has been removed cannot be used for printing. If it is used, a printer failure might occur. Screw Doya_E.book Page 36 Thursday, November 11, 2004 10:50 AM
Page: 37
Troubleshooting Additional information EN-37 6 Pull the paper out. 7 Turn on the printer. 8 Re-set the paper-in tray. If the printer operates normally, the paper jam problem has been solved. You can continue printing. If the ribbon cartridge is removed during printing 1 Turn off the printer. 2 Insert the ribbon cartridge all the way, and then be sure to close the ribbon cartridge door. 3 Turn on the printer. If the paper-in tray is removed during printing 1 Turn off the printer. 2 Insert the paper-in tray all the way. 3 Turn on the printer. Tips • Printing ends when the sheet in process is printed. • An error also occurs if you remove the paper-in tray before printing starts. Retry the procedure from the beginning. For details, refer to “Loading paper” (gpage 22). Doya_E.book Page 37 Thursday, November 11, 2004 10:50 AM
Page: 38
About the Paper-in Tray/Ribbon Cartridge Additional information EN-38 About the Paper-in Tray/Ribbon Cartridge • Be sure to use the correct Paper-in Tray/Ribbon Cartridge for the paper size you are using, otherwise, a malfunction may occur. • When ordering, please specify the models indicated in the table below (as of November, 2004). - The Paper-in Tray/Ribbon Cartridges are available in two types: P-P50S - containing 100 × 148 mm (4 × 6) paper and a corresponding ribbon cartridge. P-L50S* - containing 89 × 127 mm (3.5" × 5") paper and a corresponding ribbon cartridge. - Use a ribbon cartridge and paper-in tray for the size of paper to be used, otherwise, print error may occur. * P-L50S is not available in certain local areas. • The used ribbon cartridge is not reusable. • Handle ribbon cartridges carefully to ensure that they remain clean. • Do not disassemble ribbon cartridges. • Fingerprints, dust, scratches, oil, or other debris on the print surface may degrade printing quality. • Do not use sheets of paper that have already been printed on. A failure might occur. Do not use sheets of paper that have been ejected. • Do not open Paper-in Tray/Ribbon Cartridges until you are ready to use them. Storage considerations Avoid the following places or conditions when storing Paper-in Tray/Ribbon Cartridges. - Do not store Paper-in Tray/Ribbon Cartridges in places subject to extreme temperatures (30°C (86°F) or higher or 5°C (41°F) or lower), or in places exposed to excessive dust or moisture. - Do not leave Paper-in Tray/Ribbon Cartridges in the places that are exposed to direct sunlight or other sources of strong light. Observe this instruction also when the Paper-in Tray/Ribbon Cartridges are loaded on the printer. - Do not store Paper-in Tray/Ribbon Cartridges together with chemicals. Type of Paper-in Tray/Ribbon Cartridge Model Capacity Paper-in Tray/Ribbon Cartridge for 100 × 148 mm (4 × 6) printing P-P50S 50 Paper-in Tray/Ribbon Cartridge for 89 × 127 mm (3.5" × 5") printing P-L50S 50 Doya_E.book Page 38 Thursday, November 11, 2004 10:50 AM
Page: 39
About the Paper-in Tray/Ribbon Cartridge Additional information EN-39 Notes on storing printed paper • Do not store printed paper with their printed surfaces facing each other. • Do not leave the printed surface in contact with an adhesive tape, desk mats, plastic erasers, or similar objects for a long time. Discoloration might occur. • Do not apply organic solvent to printed surfaces. Discoloration might occur. • Do not expose printed surfaces to sunlight or other strong light sources for a long time. Discoloration might occur. • Use an oil felt-tipped pen when writing on printed surfaces. • Do not store printed paper in a place that is exposed to direct sunlight or will become hot or moistened. Keep printed paper away from children. • OLYMPUS will not compensate for discoloration or fading of printed sheets of paper. Compensation for problems Exchange will be made for the same quantity of new product if a problem occurs as the result of an OLYMPUS manufacturing defect. OLYMPUS is not responsibility in other situations. Doya_E.book Page 39 Thursday, November 11, 2004 10:50 AM
Page: 40
Service and maintenance Additional information EN-40 Service and maintenance • The product will come with a warranty card. Make sure that the dealer name and purchase date are written or stamped on the warranty. If any of the necessary information is missing, contact the dealer. Please read through the warranty and store it in a safe place. • If you have a question about after-sale services for this product or encounter a failure, contact the dealer or our service center. Within one year of the purchase date, we will repair the product free of charge if it becomes faulty, provided that the instructions in this manual were observed. • There will generally be a charge for repairs performed after the warranty period has expired. • Maintenance parts for this product will be stored for about five years after production stops. Within this period, we can accept repair requests. Even after this period, repair may be possible. Contact the dealer or our service center. • OLYMPUS will not compensate for any damage or loss (photography cost, loss of photography profits, etc.) incurred as a consequence of a failure of this product. Postage and packing costs are the responsibility of the sender. • When sending the product to us for maintenance, place it in the original box with the original packing material, and enclose a letter indicating the location that requires repair. If the original packing material is not available, pack the printer with enough cushion to absorb any impacts during transportation. Use a door- to-door package delivery service or registered parcel mail so that you have proof of sending the product. Doya_E.book Page 40 Thursday, November 11, 2004 10:50 AM
Page: 41
Specifications Additional information EN-41 Specifications Printer AC adapter • Requires a power cord that meets the safety standards of your country. • The specifications and design are subject to change without notice. Printing method Dye sublimation thermal transfer printing Resolution 306 dpi Paper size 3.5" × 5" paper : 89 × 127 mm (3.5" × 5") (H × W) 4 × 6 paper : 100 × 148 mm (3.9" × 5.8") (H × W) (after perforated) Color representation Over 16.77 million colors Printing speed 3.5" × 5" paper : Approx. 84 seconds per sheet 4 × 6 paper : Approx. 88 seconds per sheet (excluding data transmission time from digital camera or PC) Interfaces Connection to a PictBridge-compatible digital camera: USB A-type connector Connection to a PC: USB B-type connector Connection to a Dock&Done system: Dock&Done connector Compatible OS Windows 98SE/Me/2000/XP Mac OS X v10.3 and later Ink ribbon cartridge Yellow+Magenta+Cyan layers and coating (protective layer) Compatible image file formats Exif 1.0 to 2.2 (JPEG/TIFF) DPOF 1.1 Power source DC 25V (dedicated AC adapter) Power consumption 47.5 W (printing), 2.5 W (standby) Operating temperature 10 - 35°C (50 - 95°F) Operating humidity 30 to 80% Dimensions 167 × 145 × 70 mm (6.6" × 5.7" × 2.8") (W × D × H) (protruding parts excluded) Base machine mass 1.1 kg (38.8 oz.) Type Switching regulator Input voltage AC 100-240V, 50/60 Hz Output voltage DC 25V Doya_E.book Page 41 Thursday, November 11, 2004 10:50 AM
Page: 42
Before you contact us Additional information EN-42 Before you contact us • Confirm the following points before contacting us so that we can provide quick and accurate answers. • Please fill out this check sheet if you want to contact us by fax or mail. • Symptom, displayed messages, frequency, and other details of the problem: PC-related problems are difficult to accurately identify. Please provide as much detail as possible. • Name: • Contact information:Postal code Address (your residential address or office address) Phone/Fax E-mail • Product name (model): • Serial number (located on the bottom of the product): • Purchase date: • Error message displayed on the camera screen: * If you are using this printer connected to a PC, or if you are using third party application software, please provide as much detail as possible, as follows. • Type of PC: Manufacturer, model, and others • Memory size and free hard disk space: • OS name and version: For Mac OS, check settings on the Control Panel and the extensions in use. For Windows, check settings on Control Panel/System/Device Manager. • Other peripheral devices connected: • Name and version of the application software related to your problem: • Name and version of the OLYMPUS software product related to your problem: Doya_E.book Page 42 Thursday, November 11, 2004 10:50 AM
Page: 43
MEMO Doya_E.book Page 43 Thursday, November 11, 2004 10:50 AM
Page: 44
MEMO Doya_E.book Page 43 Thursday, November 11, 2004 10:50 AM
Page: 45
Piezas y controles Lea esto primero ES-16 Piezas y controles Parte delantera Parte trasera PAPE R RIBB ON AC CE SS C E F D B A G H I J K PA PE R RIB BO N AC CE SS O N M Q P L Doya_E.book Page 16 Thursday, November 11, 2004 10:50 AM
Page: 46
MEMO Doya_E.book Page 43 Thursday, November 11, 2004 10:50 AM
Page: 47
MEMO Doya_E.book Page 44 Thursday, November 11, 2004 10:50 AM
Page: 48
MEMO Doya_E.book Page 45 Thursday, November 11, 2004 10:50 AM
Page: 49
MEMO Doya_E.book Page 46 Thursday, November 11, 2004 10:50 AM
Page: 50
MEMO Doya_E.book Page 47 Thursday, November 11, 2004 10:50 AM

Question & answers

Have a question about the Olympus P-S100 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Olympus P-S100. Please make sure that you describe your difficulty with the Olympus P-S100 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Olympus P-S100

Name
Email
Reaction

View a manual of the Olympus P-S100 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Olympus
  • Product: Not categorized
  • Model/name: P-S100
  • Filetype: PDF
  • Available languages: English, Spanish, French