Olympus Camedia P-10 manual

User manual for the Olympus Camedia P-10 in English. This PDF manual has 148 pages.

Page: 1
DIGITAL PHOTO PRINTER P-10 Instruction Manual ENGLISH )2 Manuel d’utilisation FRANÇAIS )36 Bedienungsanleitung DEUTSCH )72 Manual de instrucciones ESPAÑOL )110 p10_e_000_bookfile.book Page 1 Monday, December 15, 2003 11:51 AM
Page: 2
2 ENGLISH Thank you for purchasing this OLYMPUS digital photo printer P-10. Read this manual carefully prior to use to ensure correct use of this product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult your nearest OLYMPUS service center or an experienced radio/TV technician for help. WARNING: The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with device. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. This class B digital apparatus complies with Canadian ICES-003. “CE” mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. “CE” mark printers are intended for sales in Europe. Windows is registered trademark of Microsoft Corporation. For customers in USA For customers in Canada For customers in Europe Trademarks p10_e_000_bookfile.book Page 2 Monday, December 15, 2003 11:51 AM
Page: 3
3 Preparation Printing For Your Information Introduction ENGLISH Contents Safety precautions ..................................................................................... 4 Care and storage ....................................................................................... 9 What this printer can do ........................................................................... 10 Unpacking the printer............................................................................... 11 Identifying the parts.................................................................................. 12 Connecting the power supply/Turning the printer on and off ................... 14 Loading the ink ribbon cartridge............................................................... 15 Loading paper .......................................................................................... 18 Loading paper into the paper tray..................................................................... 18 Installing the paper tray into the printer ............................................................ 20 Printing images from digital camera......................................................... 21 About PictBridge compatible digital cameras ................................................... 21 Connecting a digital camera to the printer ........................................................ 21 Using the digital camera to control the print operation ..................................... 22 Printing images from PC .......................................................................... 23 Connecting the printer to a PC ......................................................................... 23 Installing the Printer Driver (during initial setup) ............................................... 24 Printing.............................................................................................................. 24 Replenishing the paper supply and replacing the ink ribbon cartridge..... 26 If paper runs out while printing.......................................................................... 26 If ink ribbon runs out while printing ................................................................... 26 If indicators light steadily and blink........................................................... 27 Troubleshooting ....................................................................................... 28 If paper is jammed ............................................................................................ 29 If the Ink ribbon cartridge is removed during printing........................................ 30 About the print pack (ink ribbon cartridge and paper).............................. 31 Specifications........................................................................................... 33 Service and Maintenance......................................................................... 34 Definition of terms .................................................................................... 35 Introduction Preparation Printing For Your Information p10_e_000_bookfile.book Page 3 Monday, December 15, 2003 11:51 AM
Page: 4
4 Preparation Printing For Your Information Introduction ENGLISH Introduction Safety precautions Various icons are used in this manual to indicate correct product use, and help prevent property damage and injury to customers and others. The meanings of these icons are described below. Precautionary notations are indicated by the following symbols. Icon Description WARNING Failure to follow instructions indicated by this icon may lead to serious injury or death. NOTE Failure to follow instructions indicated by this icon may lead to injury or property damage. Icon Description Do not perform this action. You are strongly encouraged to perform this action. Unplug the device from the power source. Do not disassemble. Avoid contact with water and other liquids. Do not touch if your hands are wet. p10_e_000_bookfile.book Page 4 Monday, December 15, 2003 11:51 AM
Page: 5
5 Safety precautions Preparation Printing For Your Information Introduction ENGLISH WARNING J If this device acts abnormally, unplug it Do not use the printer if it emits smoke, unusual smells, strange sounds, or becomes unusually warm. Use under these conditions may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest OLYMPUS service center. J Should any liquid or foreign objects get into the printer, unplug the power cord Do not allow any liquids, metals, or flammable objects to get into the printer through the ventilation holes. This may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest OLYMPUS service center. J If the printer cabinet is damaged, unplug the power cord Do not use this device if the cabinet (body) is damaged. Use in this condition may cause fire or electric shock. Turn off and unplug the printer. Then contact your nearest OLYMPUS service center. J If the power cord is damaged, unplug it Do not use a damaged power cord. Use in this condition may cause fire or electric shock. Turn the printer off, and unplug the power cord being careful not to touch any exposed wires. Then contact your nearest OLYMPUS service center. p10_e_000_bookfile.book Page 5 Monday, December 15, 2003 11:51 AM
Page: 6
6 Safety precautions Preparation Printing For Your Information Introduction ENGLISH WARNING J Do not damage the power cord Do not damage or modify the power cord. A damaged power cord may result in fire or electric shock. To prevent the cord from becoming damaged, DO NOT: pull on the cord to unplug it, bend the cord excessively, or place heavy objects on the cord. If the power cord is damaged, contact your nearest OLYMPUS service center. J Do not disassemble or modify the printer The printer has both hot and high voltage parts on the inside. Touching these parts may result in burns, electric shock, and/or damage to the printer. Never attempt to disassemble or modify the printer as this may lead to electric shock or printer malfunction. For service or repair, contact your nearest OLYMPUS service center. J Do not allow liquids near the printer If liquid gets into the printer, it may result in fire or electric shock. J Do not place heavy objects on the printer Heavy objects may damage the printer cabinet, resulting in fire or electric shock. Damage may also result from the printer being dropped or falling. J Do not install the printer in the following places To prevent fire, electric shock, and printer malfunction, do not install the printer in the following places: Dusty, humid, or oily places Should any dust or liquid get into the printer, it may result in fire or electric shock. Extremely hot places Do not expose the printer to direct sunlight (for example, inside a car or near a window) or extremely high temperatures (for example, near a heater). Doing so may damage the printer cabinet, resulting in fire or electric shock. Use the printer in an environment with an ambient temperature between 5 to 35°C (41 to 95°F) and humidity of 20 to 80%. p10_e_000_bookfile.book Page 6 Monday, December 15, 2003 11:51 AM
Page: 7
7 Safety precautions Preparation Printing For Your Information Introduction ENGLISH J Do not use the printer in the following places Unstable or inclined surfaces. Outdoors (particularly on beaches, etc.), or places that expose the printer to excessive dust or debris. Places subject to rain, dripping, or enclosed places where condensation could occur such as inside a plastic bag. J Do not use the printer with an AC adapter or power cord other than that specified/provided J Do not use the provided AC adapter or power cord with any other devices J Provide correct voltage Incorrect voltage may damage printer parts. Use with incorrect voltage may cause fire or electric shock. J Connect the power cord correctly/safely For example, if the power cord is plugged in loosely, it may cause a fire or electric shock. Push the plug all the way into the outlet. J Make sure that excessive dust and debris do not accumulate on the power cord Dust and debris may conduct electricity, which can cause fire and electric shock. If excessive dust and debris accumulate on the cord, unplug the cord and clean it. J Always unplug the power cord during an electrical storm The induced electricity from storms may cause fire, electric shock, or printer malfunction. J Do not hold the power cord plug with wet hands Doing so may result in electric shock. Be sure your hands are dry before handling. J Plug the printer directly into an outlet Avoid plugging into a socket that is already being used by several appliances. p10_e_000_bookfile.book Page 7 Monday, December 15, 2003 11:51 AM
Page: 8
8 Safety precautions Preparation Printing For Your Information Introduction ENGLISH NOTE J Do not block the ventilation holes Do not block the ventilation holes on the front and back of this printer.Doing so may cause heat in the printer to build up, possibly resulting in fire or electric shock. Do not put the printer where there is poor ventilation, or on a soft surface such as a rug or bed. J Do not put the printer on an unstable surface Do not put the printer on an unstable surface such as a shaky table. Injury may result from the printer being dropped or falling. This could also damage the printer or cause the printer to malfunction. J Do not touch the non-user-serviceable parts inside the printer Doing so may cause injury or burns. This applies especially to children and those unfamiliar with the printer. J Do not move the printer when the power cord is taut Moving the printer when the power cord is taut may damage the cord. Using the printer when damaged may cause fire or electric shock. When moving the printer, unplug and bundle the power cord. J Do not unplug the printer by jerking or pulling on the power cord To unplug the power cord, hold it by the plug.Pulling on the cord may damage it, possibly resulting in fire or electric shock. J Unplug the printer for servicing Always unplug the printer before servicing or performing maintenance. J Unplug the printer if it will not be used for an extended period of time Unplug the printer if it will not be used for an extended period of time, such as while you are away on a long trip. Otherwise, deteriorated insulation or current leakage may cause fire or electric shock. p10_e_000_bookfile.book Page 8 Monday, December 15, 2003 11:51 AM
Page: 9
9 Preparation Printing For Your Information Introduction ENGLISH Care and storage Moisture condensation is water vapor in the air that becomes liquid, and collects on the printer surface. This phenomenon occurs under the following conditions. The room in which the printer is placed is rapidly heated or cooled. The printer is directly subjected to cool air, such as from an air conditioner. The printer is moved from a cold place to a warm place. Moisture in the air condenses on the paper, deteriorating print quality or causing paper jams. Under conditions where condensation has occurred or may occur, do not operate the printer until it is dry or until there is no possibility that condensation will occur. Spraying an insecticide near the printer, or wiping it with thinner or benzene for example, may damage or discolor the printer cabinet. Use a soft cloth to clean the outside of the printer cabinet. For difficult to remove stains, dampen a soft cloth with water or a mild detergent diluted with water, and wring out the cloth to remove as much of the moisture as possible before wiping the outside of the cabinet. Deterioration and discoloration may occur if the printer is in contact with rubber or plastic products for an extended period of time. If the printer is not used for an extended period of time, it may malfunction. Operate the printer at least once every six months. When lifting or carrying the printer, use both hands. When transporting the printer, place it in the original box with the original packing material. If you don't have the original packaging, pack the printer with enough cushioning material to absorb any impacts during transportation. Protect against moisture condensation Do not spray on or allow volatile solvents to come in contact with the printer Do not allow the printer to be in contact with rubber or plastic products for an extended period of time Operate the printer at least once every six months Carry the printer with both hands Transport the printer carefully p10_e_000_bookfile.book Page 9 Monday, December 15, 2003 11:51 AM
Page: 10
10 Preparation Printing For Your Information Introduction ENGLISH What this printer can do Direct Print This printer supports the PictBridge standard for communication between a digital camera and printer. Connect a PictBridge compatible digital camera to this printer using a USB cable, and create prints from the digital camera. Making a variety of prints This printer supports multi prints where multiple copies of one image are printed on a page, index prints where several different images are printed on a page, date print where the photograph date is printed, and bordered/borderless prints. Caution Depending on the digital camera that is connected, some functions may be restricted. Printing images from a PC Connect this printer to a PC using a USB cable, and create prints from images stored on the PC. High-quality overcoated prints High-quality overcoated prints provide excellent storability and durability. You can protect your important pictures from the effects of time. 50-sheet continuous print The supplied paper tray can continuously supply up to 50 sheets of paper to the printer. A single sheet of 3.5" × 5" Paper takes about 40 seconds to print (excluding data transmission time from digital camera or PC). p10_e_000_bookfile.book Page 10 Monday, December 15, 2003 11:51 AM
Page: 11
11 Preparation Printing For Your Information Introduction ENGLISH Unpacking the printer Make sure that the following accessories are supplied with your printer. If you are missing any of these accessories, contact your nearest OLYMPUS service center immediately. Starter kit Ink ribbon cartridge for 4 × 6 printing (for 5 prints) and 4 × 6 Paper (5 sheets) Instruction manual (1) User registration card (1) (Depending on country, may not be supplied with printer.) Warranty card (1) CD-ROM (Printer driver) (1) AC adapter (1) Power cord (1) Paper tray (1) Conversion tray (for 3.5" × 5" Paper) (1) (Place this tray in the paper tray. Depending on country, may not be supplied with printer.) p10_e_000_bookfile.book Page 11 Monday, December 15, 2003 11:51 AM
Page: 12
12 Preparation Printing For Your Information Introduction ENGLISH Identifying the parts QFront QPaper tray POWER button ( P.14) POWER indicator ( P.27) Ventilation holes Paper tray door ( P.20) RIBBON indicator ( P.27) PAPER indicator ( P.27) ACCESS indicator ( P.27) Cartridge door ( P.15) Cartridge slot Tab ( P.16) Paper eject section PictBridge connector ( P.21) Cartridge door tab ( P.15) Paper tray door tab ( P.20) Conversion tray ( P.18, 19) Tray cover Tray cover tab ( P.18) p10_e_000_bookfile.book Page 12 Monday, December 15, 2003 11:51 AM
Page: 13
13 Identifying the parts Preparation Printing For Your Information Introduction ENGLISH QBack QBottom Paper stopper ( P.22, 23) USB connector ( P.23) DC-IN terminal ( P.14) Ventilation holes Paper dispenser slot ( P.30) p10_e_000_bookfile.book Page 13 Monday, December 15, 2003 11:51 AM
Page: 14
14 Preparation Printing For Your Information Introduction ENGLISH Preparation Connecting the power supply/Turning the printer on and off 1 Plug the printer power cord into the AC adapter. 2 Plug the AC adapter power cord into a wall outlet, then plug the other end of the printer power cord into the printer's DC-IN terminal. 3 Press the POWER button. The POWER indicator lights, and the printer turns on. Caution If you are connecting to a digital camera, turn the printer on, connect the digital camera to the printer, and then turn on the digital camera. P.21 If you are connecting to a PC, connect to the PC, and then turn the printer on before turning on the PC. To turn off the printer Press the POWER button to turn off the printer. The POWER indicator goes out, and the printer turns off. Caution If the printer power cord is accidentally unplugged from the printer during printing, turn the printer off, plug the printer power cord into the printer's DC-IN terminal, and then turn the printer on again. Leaving the printer unplugged in printing mode may cause it to malfunction. DC plug p10_e_000_bookfile.book Page 14 Monday, December 15, 2003 11:51 AM
Page: 15
15 Preparation Printing For Your Information Introduction ENGLISH Loading the ink ribbon cartridge About the print pack You need the provided starter kit or an optional print pack for printing. Always use the ink ribbon cartridge and print paper supplied together in the same carton. Do not use printed paper or paper that has been fed through the printer. 1 Open the cartridge door while pushing down on the cartridge door tab. 2 Release the ink ribbon cartridge stop, and wind the ink ribbon to remove the slack. To continue using a partially used ink ribbon cartridge, insert after removing slack as shown in the drawing. While pressing the center of the reel, wind the ink ribbon in the direction of the arrow. p10_e_000_bookfile.book Page 15 Monday, December 15, 2003 11:51 AM
Page: 16
16 Loading the ink ribbon cartridge Preparation Printing For Your Information Introduction ENGLISH 3 Insert the ink ribbon cartridge all the way into the compartment and close the cartridge door firmly. Press from the center of the ink ribbon cartridge to slide it fully into the compartment, until you hear a locking sound. If you can’t close the cartridge door, remove the ink ribbon cartridge, and then re-insert it. Removing the ink ribbon cartridge Open the cartridge door, lift up on the tab to release the ink ribbon cartridge, and remove the cartridge. p10_e_000_bookfile.book Page 16 Monday, December 15, 2003 11:51 AM
Page: 17
17 Loading the ink ribbon cartridge Preparation Printing For Your Information Introduction ENGLISH Caution The cartridge compartment may be very hot during or after operation. Do not insert your finger or hand into the cartridge compartment. The print packs are either for 4×6 or 3.5"×5" paper. When printing on 4×6 paper, be sure to use an ink ribbon cartridge for 4×6 printing. When printing on 3.5"×5" paper, use an ink ribbon cartridge for 3.5"×5" printing. When setting an ink ribbon cartridge down, stand it on its side to avoid getting dust on the ink ribbon. Do not touch the ink ribbon, or leave it where it may collect dust. Fingerprints or dust on the ink ribbon may degrade print quality. If the ink ribbon tears, replace it with a new ink ribbon cartridge. Storage considerations Do not store the ink ribbon cartridge in a place subject to high temperature or humidity, excessive dust or direct sunlight. P P L L Ink ribbon cartridge for 4×6 printing Ink ribbon cartridge for 3.5"×5" printing p10_e_000_bookfile.book Page 17 Monday, December 15, 2003 11:51 AM
Page: 18
18 Preparation Printing For Your Information Introduction ENGLISH Loading paper To print 4 × 6 Paper 1 Grasp both tray cover tabs to open the tray cover and remove the conversion tray. 2 Load paper into the paper tray with the print surface facing down. Remove the protective sheet, and insert the paper. Up to 50 sheets can be loaded into the tray cover. 3 Close the tray cover of the paper tray. Make sure that paper is not pinched in the paper tray. Loading paper into the paper tray Printed surface down p10_e_000_bookfile.book Page 18 Monday, December 15, 2003 11:51 AM
Page: 19
19 Loading paper Preparation Printing For Your Information Introduction ENGLISH To print 3.5" × 5" Paper When loading 3.5" × 5" Paper for printing, install the conversion tray to the paper tray before inserting the paper. Caution Be careful not to stain or damage the conversion tray. Do not touch the print surface (the blank, glossy surface) when handling paper. Do not store in a place subject to high temperature, humidity or direct sunlight. Do not leave paper in a place subject to excessive dust. Fingerprints or dust on the print surface may degrade print quality. To prevent malfunction, use only the specialty paper recommended for this printer. A maximum of 50 sheets of paper can be placed in the paper tray. Be careful not to exceed this number when adding print paper. If too many print paper sheets are loaded, the printer may jam. To prevent paper from jamming, do not fold or bend print paper. Do not write on paper before printing images on it. If you want to write something, be sure to do so after printing, using an oil based ink. It is not possible to print word processor or typewriter characters on this paper. Conversion tray p10_e_000_bookfile.book Page 19 Monday, December 15, 2003 11:51 AM
Page: 20
20 Loading paper Preparation Printing For Your Information Introduction ENGLISH 1 Open the paper tray door by pulling the paper tray door tab. To close the door, push it until the paper tray door tab locks with a click. 2 Insert the paper tray all the way. Insert the paper tray until you hear a locking sound. To remove, grasp the portion indicated by the arrow and pull out toward you. Installing the paper tray into the printer p10_e_000_bookfile.book Page 20 Monday, December 15, 2003 11:51 AM
Page: 21
21 Preparation Printing For Your Information Introduction ENGLISH Printing Printing images from digital camera This printer can print images directly from any PictBridge compatible digital camera. Operations to print the images are issued from the digital camera, and vary depending on the digital camera. See the operations manual for the digital camera for details concerning printing. Additionally, information concerning PictBridge-compatible digital cameras is available on the OLYMPUS web site. Caution To print pictures that were not taken with a digital camera, print from a PC. Use the cable supplied with the digital camera to connect. 1 First, turn the printer on. See the Page 14. “Connecting the power supply/Turning the printer on and off”. 2 Insert the USB cable into the digital camera USB connector, and plug the other end into the PictBridge connector on the front of the printer. 3 Turn the digital camera on and set it so it is ready to print. The ACCESS indicator on the printer lights, and shortly thereafter turns off. Refer to the digital camera’s operation manual for details on digital camera operation. About PictBridge compatible digital cameras Connecting a digital camera to the printer p10_e_000_bookfile.book Page 21 Monday, December 15, 2003 11:51 AM
Page: 22
22 Printing images from digital camera Preparation Printing For Your Information Introduction ENGLISH 4 Pull the paper stopper on the top of the printer down toward the front. 1 Control print operations using the digital camera. After printing begins, the ACCESS indicator on the printer will blink. When printing is finished, the indicator turns off. See the digital camera operations manual for details on digital camera operations. 2 After printing is complete, turn off the digital camera and printer before removing the USB cable. Caution Never open the cartridge door or paper tray door during printing. Do not move the printer during printing. Do not turn off printer or digital camera, or remove the AC adapter during printing. In the event that power is interrupted or the AC adapter removed, restore power and perform the interrupted operations again. Leaving the printer unplugged in printing mode may cause it to malfunction. Using the digital camera to control the print operation GO SELECt Sample Digital Camera display p10_e_000_bookfile.book Page 22 Monday, December 15, 2003 11:51 AM
Page: 23
23 Preparation Printing For Your Information Introduction ENGLISH Printing images from PC Print images from a PC using any image processing application software. Caution To print pictures that were not taken with a digital camera, print from a PC. Use a commercially available USB cable (Type A-B) to connect the printer. 1 Insert the USB cable plug into the PC USB port, and plug the other end into the USB connector on the back of the printer. 2 Pull the paper stopper on the top of the printer down toward the front. 3 Turn the printer on. Notes If both a PC and a PictBridge compatible digital camera are connected to the printer at the same time, the digital camera connection has priority over the PC. Disconnect the digital camera to print images from PC. This printer is not guaranteed to work on a network. Additionally, use of a commercial printer buffer is not protected by the limited warranty. This printer is not guaranteed to work when connected to a USB hub. Connecting the printer to a PC p10_e_000_bookfile.book Page 23 Monday, December 15, 2003 11:51 AM
Page: 24
24 Printing images from PC Preparation Printing For Your Information Introduction ENGLISH Supported Operating Systems: Windows 98/Me/2000/XP 1 Start the PC, and insert the CD-ROM supplied with the printer into the CD-ROM drive. The [New Hardware Found] dialog is automatically displayed. If this dialog is not automatically displayed, start installation of the driver by selecting [Settings - Printers - Add Printer] from the Start menu. If you are using Windows XP, start installation of the driver by selecting [Control Panel - Printers and Faxes - Add a printer] from the Start menu. 2 Follow the directions on the screen to install the printer driver. See the PC operations manual for details. 1 Use the image processing application to display the desired image, and select the image for printing. 2 Select [Print] from the File menu, and select [OLYMPUS P-10] from the available printer list. Notes [Print] operations and printer selection vary depending on the application. Refer to the instructions for the application you are using. 3 Click [Properties] to change settings before printing. Installing the Printer Driver (during initial setup) Printing p10_e_000_bookfile.book Page 24 Monday, December 15, 2003 11:51 AM
Page: 25
25 Printing images from PC Preparation Printing For Your Information Introduction ENGLISH Printer settings On the [Properties] window, use the [Paper] and [Graphics] tabs to change the paper size, number of copies, and to make adjustments to the color settings. For details, refer to the ReadMe file contained in the CD-ROM. Caution Never open the cartridge door or paper tray door during printing. Do not move the printer during printing. Do not turn off the printer or PC, or remove the AC adapter during printing. In the event that power is interrupted or the AC adapter removed, restore power and perform the interrupted operations again. Leaving the printer unplugged in printing mode may cause it to malfunction. Example of the [Paper] tab window Example of the [Graphics] tab window p10_e_000_bookfile.book Page 25 Monday, December 15, 2003 11:51 AM
Page: 26
26 Preparation Printing For Your Information Introduction ENGLISH For Your Information Replenishing the paper supply and replacing the ink ribbon cartridge The PAPER indicator blinks slowly. Replenish the paper supply in the paper tray. The remaining copies will automatically continue to print. The ink ribbon normally ends at the same time the paper in a print pack is used up, so please replace the ink ribbon cartridge at the same time. The RIBBON indicator blinks fast. After the paper has ejected from the printer, replace the ink with a new ink ribbon cartridge. After closing the cartridge door, the remaining copies will automatically continue to print. If paper runs out while printing If ink ribbon runs out while printing p10_e_000_bookfile.book Page 26 Monday, December 15, 2003 11:51 AM
Page: 27
27 Preparation Printing For Your Information Introduction ENGLISH If indicators light steadily and blink * When communication is successfully established, the light turns off. Indicator Lamp status Printer status Necessary countermeasure Page POWER On Power ON — 14 Off Power OFF ACCESS On * Connecting to digital camera Do not disconnect the digital camera or PC. — Blinking slowly Communi- cating Blinking very slowly Printing — — PAPER Blinking slowly Out of paper Remove the paper tray, refill paper in the tray, and replace the tray in the printer. 18,26 The paper and ink ribbon cartridge are incompatible When printing on 4×6 paper, be sure to use an ink ribbon cartridge for 4×6 printing. When printing on 3.5"×5" paper, use an ink ribbon cartridge for 3.5"×5" printing. 17 RIBBON Blinking rapidly End of ink ribbon Replace the ink ribbon cartridge with a new one. 15,26 Blinking slowly Ink ribbon cartridge not installed Install an ink ribbon cartridge on the printer. 15 The paper and ink ribbon cartridge are incompatible When printing on 4×6 paper, be sure to use an ink ribbon cartridge for 4×6 printing. When printing on 3.5"×5" paper, use an ink ribbon cartridge for 3.5"×5" printing. 17 ACCESS, PAPER Blinking simulta- neously Paper jam Remove jammed paper. 29 ACCESS, RIBBON Blinking simulta- neously Communi- cation error Ensure that the digital camera is PictBridge compatible. — Turn the printer off and ON, then retry printing. If the error persists, consult your nearest OLYMPUS service center. — ACCESS, RIBBON, PAPER Blinking simulta- neously Internal problem Consult your nearest OLYMPUS service center. — p10_e_000_bookfile.book Page 27 Monday, December 15, 2003 11:51 AM
Page: 28
28 Preparation Printing For Your Information Introduction ENGLISH Troubleshooting Before sending your printer for service, check the following to try to resolve the problem. If the problem persists, contact your nearest OLYMPUS service center. Problem Cause·Status Resolution Page Cannot turn the printer on. The AC adapter is not connected. Connect the AC adapter properly. 14 Cannot remove the ink ribbon cartridge. The printer turned off during the operation. Push the ink ribbon cartridge in until you hear a locking sound. Turn the printer on again and wait until the mechanical sound stops. — Printing from the digital camera takes a long time to start. The printer takes a long time to open a TIFF file. Opening time varies depending on the image size. Wait until opening finishes. — Trimming selected by DPOF takes a long time. Wait until opening finishes. — Cannot print. The ink ribbon cartridge is not Inserted. Insert an ink ribbon cartridge. 15 Paper or the paper tray is not inserted. Load paper into the paper tray and then install the paper tray. 18, 20 Paper is jammed at the paper eject section. Remove the paper. 29 The printer driver is not properly installed on the PC. Install or re-install the printer driver on the PC. 24 Indicators light or blink — 27 Noise interferes with printed images. Pictures that were not taken with a digital camera were printed from a digital camera. Use a PC to print image data that has not been recorded by a digital camera. 23 Printing intervals have gotten longer. Printing intervals are automatically extended during continuous printing to prevent the internal components from overheating. This is not a malfunction. Wait a few minutes. — p10_e_000_bookfile.book Page 28 Monday, December 15, 2003 11:51 AM
Page: 29
29 Troubleshooting Preparation Printing For Your Information Introduction ENGLISH If paper jams in the printer, the ACCESS indicator and PAPER indicator both blink, and printing stops. Follow the steps below to clear a paper jam in the printer. 1 Turn the printer off. 2 After removing the paper tray, make sure that no print paper is bent or curled and that paper sheets are properly placed in the tray. 3 With the paper tray removed, turn the printer on again to automatically eject the paper from the printer. If paper is automatically ejected, continue with step 8. If paper is not automatically ejected, turn the printer off and continue with step 4. 4 Look in the paper tray door to see if the jammed paper is visible at the back. If the jammed paper is visible, go to Step 5. If the jammed paper is not visible, contact your nearest OLYMPUS service center for repairs. If paper is jammed p10_e_000_bookfile.book Page 29 Monday, December 15, 2003 11:51 AM
Page: 30
30 Troubleshooting Preparation Printing For Your Information Introduction ENGLISH 5 Set the printer on its rear so that the front of the printer is facing up. Insert your finger in the paper dispenser slot located on the bottom and slide the jammed paper towards the paper tray door. If you cannot move the paper with your finger, use tweezers or the like. 6 After the paper has moved partway, you will then be able to remove it through the paper tray door. 7 Turn the printer on. 8 Reinsert the paper tray in the paper tray door. If operation is normal, the paper jam has been successfully cleared and you can continue printing. Caution After removing the jammed paper, do not attempt to use it again in the printer. Doing so may damage your printer. 1 Turn the printer off. 2 Insert the ink ribbon cartridge all the way into the compartment, and close the cartridge door firmly. 3 Turn the printer on. If the Ink ribbon cartridge is removed during printing p10_e_000_bookfile.book Page 30 Monday, December 15, 2003 11:51 AM
Page: 31
31 Preparation Printing For Your Information Introduction ENGLISH About the print pack (ink ribbon cartridge and paper) J Always use print packs specified by OLYMPUS. The print packs are either for 4×6 or 3.5"×5" paper. The print pack for 4×6 printing contains 4×6 paper and an ink ribbon cartridge for 4×6 printing. The print pack for 3.5"×5" printing likewise contains 3.5"×5" paper and an ink ribbon cartridge for 3.5"×5" printing. * The print pack for 3.5"×5" printing may not be available in all locations. Always use the ink ribbon cartridge and paper from a print pack together. J The used ink ribbon cartridge is not reusable. J Exercise care when handling the ink ribbon cartridge to ensure that it remains clean. J Do not disassemble the ink ribbon cartridge. J Fingerprints, dirt, scratches, oil or other debris on the print surface may degrade print quality. J To avoid printer malfunction, never print more than once on a single sheet of paper. In addition, do not use paper that has been fed through the printer. J Do not open the print pack until ready to use. Storage Considerations J Do not store the print pack in the following locations. Do not store the print pack where hot (above 30°C), cold (below 5°C), highly humid, or dusty. Do not store the print pack with chemicals. Do not store the print pack where exposed to direct sunlight or bright light. Caution Do not place for long periods an environment exceeding 40°C. The same precautions are also necessary when installed in the printer. (Such as during transport, or by a window in direct sunlight.) p10_e_04_6.fm Page 31 Wednesday, December 17, 2003 11:33 AM
Page: 32
32 About the print pack (ink ribbon cartridge and paper) Preparation Printing For Your Information Introduction ENGLISH Storing prints J Do not store the prints with the printed surfaces facing each other. J Do not allow the print surface to be in contact with cellophane tape, a desk pad or an eraser containing plastic for an extended period of time. Prolonged contact may cause the print surface to become discolored. J Do not allow organic solvents to come in contact with the print surface. Such contact may cause discoloration. J Avoid prolonged exposure of the print surface to sunlight or bright light. Prolonged exposure may cause the print surface to become discolored. J Use an oil-based pen when writing on the print surface. J Avoid locations that are subject to direct sunlight, high temperature/ humidity, or are in the reach of children. J OLYMPUS is not responsible for print discoloration or fading. Disposing of used ink ribbon cartridge J Dispose of a used ink ribbon cartridge in compliance with the plastic waste disposal method prescribed by your local authorities. If you experience problems J Exchange will be made for the same quantity of new product if a problem occurs as the result of an OLYMPUS manufacturing defect. OLYMPUS is not responsibility in other situations. p10_e_000_bookfile.book Page 32 Monday, December 15, 2003 11:51 AM
Page: 33
33 Preparation Printing For Your Information Introduction ENGLISH Specifications Printer AC adapter Design and specifications are subject to change without notice. Printing Method Sublimation dye transfer printing 4-pass printing (Yellow/Magenta/ Cyan and protective overcoat layer) Resolution 310 dpi Print paper size 3.5" × 5" Paper: 89 (H) × 127 (V) mm (3.5" × 5") 4 × 6 Paper: 100 (H) × 148 (V) mm (3.9" × 5.8") Color expression Over 16.77 million colors Printing Speed 3.5" × 5" Paper: Approx. 40 seconds per sheet 4 × 6 Paper: Approx. 44 seconds per sheet (excluding data transmission time from digital camera or PC) Interfaces PictBridge compatible digital camera connection: USB Type-A connector PC connection: USB Type-B connector Compatible OS Windows 98/Me/2000/XP Ink ribbon cartridge Y+M+C 3 layers and light-resistant overcoat (protective layer) Compatible Graphics File Formats Exif 1.0-2.2 compatible(JPEG/TIFF) DPOF 1.1 compatible Power Source DC 24V (Dedicated AC adapter) Rated Power Consumption 82 W (during printing), 5.3 W (during standby) Operating Temperature 5 - 35°C (41 - 95°F) Operating Humidity 20 - 80% Dimensions 196 (W) × 190 (D) × 166 (H) mm (7.7" × 7.1" × 6.5") (not including protruding parts) Weight 2.3 kg (5.1 lbs) (including paper tray) Type Switching regulator Input voltage AC100-120V or AC220-240V, 50/60Hz (AC adapter type and voltage differ by region) Output voltage DC 24V p10_e_000_bookfile.book Page 33 Monday, December 15, 2003 11:51 AM
Page: 34
34 Preparation Printing For Your Information Introduction ENGLISH Service and Maintenance Your dealer gave you a limited warranty card that contains the dealer name and purchase date. If there are any mistakes on the card, please correct them with your dealer. Please read the limited warranty card, and keep it in a safe place. For questions concerning service, or in the event of a device problem, consult your nearest OLYMPUS service center. If a problem occurs with this device when used in accordance with the instruction manual, the limited warranty allows repair at no cost for one year after the date of purchase. There will generally be a charge for repairs performed after the warranty period has expired. OLYMPUS will attempt to maintain replacement parts for this product for 5 years after manufacture of this printer ends. Therefore, service for this printer will generally be available during this period. It may also be possible to receive service after this period. If necessary, please consult your nearest OLYMPUS service center. OLYMPUS is not responsible for any damages (costs or lost profits) as the result of device malfunction. When sending a product for repair, enclose documentation indicating device problem or malfunction, and ensure that the printer is adequately protected by packing material. In addition, use a traceable delivery service or registered mail. Postage costs are the responsibility of the customer. p10_e_000_bookfile.book Page 34 Monday, December 15, 2003 11:51 AM
Page: 35
35 Preparation Printing For Your Information Introduction ENGLISH Definition of terms DPOF (Digital Print Order Format) Recording format for automatic printing of digital camera data. Prints can easily be created from a media card at DPOF compatible photo shops or on printers by specifying the desired images, and number of copies. PictBridge A common standard used to connect a digital camera directly to a printer to print images. If the devices are PictBridge compatible, prints can be made using simple digital camera controls regardless of the device manufacturers. Various print options are available, such as automatic printing of DPOF specified images, index print, and image trimming. RGB The three colors comprising light: red (R), green (G) and blue (B). Colors are displayed on televisions and PC monitors using these three colors. YMC The three primary colors: cyan (C), magenta (M), and yellow (Y). Colors are printed using these three colors. The range of colors that can be displayed using YMC differs from the range of colors available using RGB. Therefore, some colors for images that are displayed on a monitor can not be reproduced exactly using a printer and are replaced with similar colors. p10_e_000_bookfile.book Page 35 Monday, December 15, 2003 11:51 AM
Page: 36
109 DEUTSCH MEMO p10_d_000_bookfile.book Page 109 Thursday, December 18, 2003 11:37 AM
Page: 37
147 ESPAÑOL MEMO p10_sp_000_bookfile.book Page 147 Thursday, December 18, 2003 10:17 AM
Page: 38
http://www.olympus.com/ © 2004 OLYMPUS CORPORATION Printed in Japan 1AG6P1P1770-- VT661401 Shinjuku Monolith, 3-1 Nishi-Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan OLYMPUS CORPORATION Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000 Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free) Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.com Olympus software updates can be obtained at: http://www.olympus.com/digital OLYMPUS AMERICA INC. Premises/Goods delivery: Wendenstrasse 14-18, 20097 Hamburg, Germany Tel: +49 40-23 77 3-0 / Fax: +49 40-23 07 61 Letters: Postfach 10 49 08, 20034 Hamburg, Germany European Technical Customer Support: Please visit our homepage http://www.olympus-europa.com or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00 for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom * Please note some (mobile) phone services/provider do not permit access or request an additional prefix to +800 numbers. For all not listed European Countries and in case that you can’t get connected to the above mentioned number please make use of the following CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899 Our Technical Customer Support is available from 9 am to 6 pm MET (Monday to Friday) Olympus Europa GmbH p10_e_05_backcover_6.fm Page 36 Wednesday, December 17, 2003 11:14 AM

Question & answers

Have a question about the Olympus Camedia P-10 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Olympus Camedia P-10. Please make sure that you describe your difficulty with the Olympus Camedia P-10 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Olympus Camedia P-10

Name
Email
Reaction

View a manual of the Olympus Camedia P-10 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Olympus
  • Product: Not categorized
  • Model/name: Camedia P-10
  • Filetype: PDF
  • Available languages: English, German, French, Spanish