P 150.2

Nilfisk P 150.2 manual

P 150.2

User manual for the Nilfisk P 150.2 in English. This PDF manual has 22 pages.

Page: 1
Printed in China Copyright © 2013 Nilfisk-Advance A/S
Page: 2
3 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions Index 1 Safety precautions and warnings .............................................3 2 Description ...............................................................................5 3 Before you start using your pressure washer...........................6 4 Operating your pressure washer ..............................................7 5 Fields of application and working methods ............................11 6 After using your pressure washer...........................................13 7 Maintenance...........................................................................14 8 Trouble Shooting ....................................................................15 9 Further information.................................................................16 10 Technical Data........................................................................19 11 EC Declaration of Conformity.................................................20 1 Safety Precautions and Warnings Before starting up your high-pres- sure washer for the first time, this instruction manual must be read through carefully. Save the instructions for later use. Safety instructions marked with this symbol must be observed to pre- vent danger to persons. This symbol is used to mark safety instruc- tions that must be observed to prevent damage to the machine and its performance. This symbol indicates tips and instructions to simplify work and to ensure a safe operation.  Warning Inhalation of aerosols can be hazardous to health. Where applicable use a device in order to avoid or reduce aer- osols production, e.g., a shield covering the nozzle. For protection against aerosols use a respiratory mask of class FFP 2 or higher. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabili- ties, or lack of experience and knowledge, unless they have been given supervision or in- struction concerning use of the appliance by a person responsi- ble for their safety. High pressure cleaners shall not be used by children or un- trained personnel. Children should be supervised to ensure that they do not play with the appliance. When transporting, operating, servicing and storing the ma- chine always make sure that it is in upright position and placed on a plain surface. Before starting up your machine please check it carefully for any defects. If you find any, do not start up your machine and con- tact your Nilfisk distributor. Especially check:  The insulation of the electric cable should be faultless and without any cracks. If the electric cable is damaged, an authorized Nilfisk distributor should replace it. WARNING!  High pressure jets can be dangerous. Never direct the water jet at persons, pets, live electrical equipment or the machine itself.  Never try to clean clothes or Symbols used to mark in- structions
Page: 3
4 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions footwear on yourself or other persons.  Hold the spray lance firmly with both hands. The spray lance is affected by a thrust of up to 16.4 N during ope- ration.  The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation. Wear goggles during opera- tion.  This appliance has been de- signed for use with cleaning agents supplied or recom- mended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance.  Disconnect from electrical power supply before carrying out user maintenance.  To ensure the appliance safety only use original spare parts from the manufacturer or approved by the manufac- turer.  High pressure hoses, fittings and couplings are important for the safety of the appli- ance. Only use hoses, fittings and couplings recommended by the manufacturer.  Do not use the appliance if a supply cord or impor- tant parts of appliance are damaged, e.g. safety device , high pressure hose and trig- ger gun.  Remove the plug from the socket outlet during cleaning or maintenance and when replacing parts or converting the machine to another func- tion.  Appropriate ear protection must be used.  Do not cover the machine during operation.  Never use the machine in an environment where there could be a danger of explo- sion. If any doubt arises, please contact the local authorities.  It is not allowed to clean asbestos-containing surfaces with high pressure.  Do not spray flammable liq- uids.  If the machine is left or not used for 5 min., it must be switched off on the start/stop switch.  This high pressure washer must not be used at tem- peratures below 0°C.  Never let any persons stay under the product when stored on the wall. WARNING! Inadequate extension cables can be dangerous. If an ex- tension cable is used, it shall be suitable for outdoor use, and the connection has to be kept dry and off the ground. It is recommended that this is accomplished by means of a cable reel which keeps the socket at least 60 mm above the ground.Cables on extension lead drums should always be completely unwound to prevent the cable from overheating. Extension cables must comply with the below-mentioned re- quirements for length and cable dimensions. 1.0 mm² max. 12.5 m 1.5 mm² max. 20 m 2.5 mm² max. 30 m  If the electric cable is damaged, it must be re- placed by the manufacturer or his service agent or simi- larly qualified person in order to avoid a hazard. Mains power connection The following should be ob- served when connecting the high pressure washer to the electric installation:  Only connect the machine to an installation with earth con- nection.  The electric installation shall be made by a certified elec- trician and comply with IEC 364.  It is recommended that the electric supply to this ap- pliance should include a residual current device that will interrupt the supply if the leakage current to earth ex- ceeds 30 mA for 30 ms. Water connection Connection to the public mains according to regulations. The machine is not suitable for connection to the potable water mains. This high pressure washer is only allowed to be con- nected with the drinking water mains, when an appropriate backflow preventer has been installed, Type BA according to EN 60335-2-79. The backflow preventer can be ordered un- der number 106411177. The length of the hose between the backflow preventer and the high pressure washer must be at least 10 metres to absorb possible pressure peaks (min diameter ½ inch). Operation by suction (for ex- ample from a rainwater vessel) is carried out without backflow preventer. Recommended suc- tion set: 126411387. As soon as water has flown through the BA valve, this water is not considered to be drinking water any more. IMPORTANT! Only use wa- ter without any impurities. If there is a risk of silt, sand or sediment in the inlet water (i.e. from your own well), an addi- tional filter should be mounted. Safety devices Locking device on spray handle (7a) (see illustration at the end of this manual): The spray handle features a locking device. When the button is activated, the spray handle cannot be operated.
Page: 4
5 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 2 Description This high-pressure washer has been developed for domestic use for cleaning: - Car, motorbike, boat, cara- van, trailer, patio/drive/flag- stones, woodwork, brickwork, barbecue, garden furniture, lawn mower Section 5 describes the use of the high-pressure washer for various cleaning jobs. Only use the high-pressure washer for purposes described in this manual. The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries. 2.1 Application 2.2 Operation elements and model survey See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet (with filter) 3 High pressure connection (only machines without hose reel) 4 High pressure hose 5 Electric cable 6 Spray lance 7 Spray handle with lock (7a) 8 Tornado® PR nozzle 9 Powerspeed® nozzle 10 Detachable detergent con- tainer 11 Nozzle cleaning tool 12 Dosing of detergents 13 Hose reel 14 Hose hook (only machines without hose reel) 15 Model tag 16 Button for telescopic handle 17 Telescopic handle 18 Turnable cable hook 19 Button for regulation of pressure and water volume Specifications: See model tag (15) of machine. We reserve the right to alter the specifications. Thermal sensor: A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sen- sor has cooled. Pressure safety device An integrated hydraulic safety valve protects the system from excessive pressure.
Page: 5
6 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 3 Before you start using your pressure washer 3.1 Mounting of holders for spray lance Mount the holders for spray lance on the machine. 3.2 Mounting of hose hook (only models without hose reel) Mount the hose hook (14) on the handle (2 screws). Note: the hose hook can be mounted on the front as well as on the back. Front position is to be used if the product is used together with a special wall hook for wall storage. 3.3 Mounting of hose reel handle (only models with hose reel) 1. Click the hose reel handle on to the trolley handle (no screws).
Page: 6
7 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 3.4 Mounting of quick coupling 1. Screw the quick coupling tight on to the water inlet (2). Note: The inlet filter must al- ways be fitted in the water inlet pipe to filter out sand, limestone and other impurities as these will damage the pump valves. Caution: Failure to fit the filter will invalidate the guarantee.  3.5 Mounting of high pressure hose Attach the high pressure hose (4) to the spray handle (7). Detach the high pressure hose by pressing the pawl. 4 Operating your pressure washer 4.1 Connection of high pres- sure hose Machines without hose reel: At- tach the high pressure hose (4) to the high pressure connection of the machine (3). Only max. 7 m additional exten- sion hose can be added. Machines with hose reel: Un- wind the high pressure hose completely.
Page: 7
8 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 4.2 Mounting of spray lance and nozzles 1. Push the spray lance (6) into the spray handle (7) and twist it until the bayonet coupling locks into position. 2. Attach the nozzle. 4.3 Water connection An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. NOTE: Connec- tion to the public mains according to regulations. IMPORTANT! Only use wa- ter without any impurities. If there is a risk of silt, sand or sediment in the inlet water (i.e. from your own well), an addi- tional filter should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat- ing the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is clean and free from debris. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 60°C). 3. Turn on the water. 4.4 Telescopic handle The machine features a tele- scopic handle. To raise or lower the handle, press the button (16) and move the handle up- wards or downwards. When a click is heard, the handle is in right position.
Page: 8
9 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions the machine. Place the entire hose in a tank or bucket. To avoid water spillage, crimp the water inlet hose down in the water and then connect the hose to the machine with the quick coupling and finally uncrimp the water inlet hose. 2. Dismount spray handle, lance and nozzle. 3. Turn the start/stop switch to position "I" and let the water run, until the air has escaped from the water hose and the pump. 4. Mount spray handle, lance and nozzle again. 4.6 Start the machine (when connected to open con- tainers (suction mode)) 4.5 Start and stop of the ma- chine (when connected to a water supply) The spray lance is affected by a thrust during opera- tion - therefore always hold it firmly with both hands. IMPOR- TANT: Point the nozzle at the ground. 1. Check that the machine is in upright position. NOTE: Do not place the ma- chine in tall grass! 2. Release the trigger lock. 3. Activate the trigger of the spray handle and let the wa- ter run until all air has es- caped from the water hose. 4. Turn the start/stop switch (1) to position "I". 5. Activate the trigger of the spray handle. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. Do not cover the machine during operation. Note: If the ma- chine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Turn the start/stop switch to position "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray handle. When releasing the trigger of the spray handle, the machine automatically stops. The ma- chine will start again when you re-activate the spray handle. The washer can take in water from a rain water tank as an example. The hose for the water supply must not be too long, approx. 5 m. Make sure that the water tank is not placed on a lower level than the machine. Use an external filter if the wa- ter contains impurities. 1. Make sure that the water hose is filled completely with water before connecting to High pressure Low pressure 4.7 Pressure regulation on the TORNADO® PR- nozzle The pressure can be regulated on the TORNADO® PR nozzle.
Page: 9
10 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 4.8 Operation with detergents Application of detergents is NOT possible if an extension hose is applied. 1. Fill the container with a de- tergent. 2. Mount the TORNADO® PR nozzle and adjust it to low pressure (see section 4.7). 3. Adjust the dosing regulator (12) to the required volume of detergent (0-5%). 4. Apply the detergent from below and upwards. 5. Let the detergent act for the time stated on the packing of the detergent and flush with pure water. Separate detergent container 1. Remove the cover with suc- tion hose from the detergent container. 2. Mount the cover with suction hose on the separate deter- gent container. The cover has a standard thread and fits common detergent con- tainers. If your container does not have a standard thread, detach the filter from the suc- tion hose and remove the cover. Remount the filter in the suction hose. Extra detergent hose can be pulled out of the machine. 4.9 Regulation of pressure / water volume Working pressure and water volume can be regulated on the machine by turning the button for regulation of pressure / wa- ter volume.
Page: 10
11 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 5 Fields of application and working methods 5.1 General Efficient high pressure cleaning is achieved by following a few guidelines, combined with your own personal experience of spe- cific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning. 5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid "super clean" areas, where the detergent collects in higher concentration and streams downwards. Let the detergent work for several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up. Otherwise the surface that has to be cleaned can be damaged. 5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical effect may be required. Special wash brushes offer this supple- mentary effect that cuts through dirt (especially by car washing).  4.10 Stationary use If mounting a special wall hook (not standard), the pressure washer can be used as a sta- tionary solution meaning that it can be operated while hanging on the wall. Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of rawl- plugs to the type of wall. On the wall hook garden/rim brush (a), brush (b) and noz- zles (c) can be stored. Important: The bearing capacity of the wall hook is max. 30 kg. a b c
Page: 11
12 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 5.2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents. Task Accessories Cleaning method Car Tornado® PR noz- zle, auto brush, underchassis spray lance, Car Combi Cleaner 1. Apply Car Combi Cleaner. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min. 2. Wash the car with the Tornado® PR nozzle. Start at the front of the car and work backwards to avoid water from penetrating by the door mouldings. 3. Use the brush for removal of traffic film which is not removed by the nozzle. If the car is very dirty, apply Car Combi Cleaner again. 4. Attach the undercarriage spray lance and clean undercarriage and wheel arches. 5. Remove water from the surface of the car with the squeegee on the car brush. Make sure that all grains of sand etc. have been removed before using the squeegee Wipe with a wash leather where the squeegee cannot reach. Rims, alu- minium Rim brush, atomizer, Alu Cleaner Apply Alu Cleaner with an automizer. Let it act for approx. 5 min. and wash with the rim brush. For steel rims, use Car Com- bi Cleaner. Wash with rim brush. Be careful! The high pressure jet may damage the tyres. Flag- stones, concrete floors and other hard surfaces Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Wash towards outlets or the like. On surfaces with moss or algae you may start by applying Stone & Wood Cleaner. Wash before the soap dries. Another more effective and quicker method is to use the Patio Cleaner. Thus you will also avoid splashes. Garden furniture, wood Wood Cleaner Garden brush Apply Wood Cleaner and wash before the soap dries. NOTE: Use the garden brush to clean off the dirt. Brickwork, Wood work Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Same method as for flagstones, but be careful - bad joints and wood may be damaged by high pressure.You may choose only to use the Tornado® nozzle. Adjust the distance (pressure) to the quality of the joints and the wood. Patio Cleaner can also be used on vertical surfaces. Gutter Underchassis spray lance Wash the gutter with the underchassis spray lance. Always wash towards down-pipes. Beware not to spray under the roofing. Cleaning of drain pipes, out- lets, down pipes etc. Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the „plug“ and flush the dirt backwards. Rust, paint Water/sandblasting equipment Mount the water/sand blasting equipment and rust and paint is efficiently and quickly removed. Beware not to damage the surface to be sandblasted. Green- house Tornado® PR nozzle, brush, Stone & Wood Cleaner Wash with high pressure and maybe a brush.You may use Stone & Wood Cleaner to remove moss and algae. Garden tools, lawn mover Tornado® PR nozzle, Power- speed® nozzle, Metal Cleaner Rinse the worst dirt off with the Tornado® PR nozzle. Apply Metal Cleaner and let it act for approx. 5 min. Wash with the nozzle.
Page: 12
13 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions  6 After using your pressure washer 6.2 Winding up of electric cable and high pressure hose up carefully. 1. Wind up the electric cable on the appropriate hooks. Built- in clip for good holding. The lower hook can be turned to release the electric cable. 2. The high pressure washer comes in two models: A) with hook for storage of high pres- sure hose (14) - B) with a hose reel (13). 6.1 Storing the washer The machine should be sto- red in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (turn the start/stop switch (1) to posi- tion “O” and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray handle. 3. Stop the machine and un- plug. Wind the electric cable round the hooks placed on the side of the machine. 4. Separate spray handle and high pressure hose. 5. Machines without hose reel: Detach high pressure hose, coil it up and place it on the hose storage. Machines with hose reel: Coil the high pressure hose up on the hose reel. 6. Place spray handle, nozzles and other accessories in the holders of the machine. Should the machine by mistake be frozen, it will be necessary to check it for damage. NEVER START-UP A FROZEN MACHINE. Frost damages are not covered by the guarantee! 6.3 Storage of accessories The standard accessories (spray handle, spray lance, nozzles and nozzle cleaning tool) can be stored on the pres- sure washer. To avoid accidents, the electric cable and the high pressure hose should always be wound
Page: 13
14 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice:  Wash off water hose, high pressure hose, spray lance and accessories before mounting.  Clean the connectors of dust and sand.  Clean the nozzles. Any repair should always be made in an authorized work- shop with original spare parts. 7 Maintenance 7.1 Cleaning of water inlet filter Clean the water inlet filter regu- larly once a month or more fre- quently according to use. Care- fully loosen the filter with a pair of pliers and clean it. Check that it is intact before re-mounting it. The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the guarantee. 7.2 Cleaning of nozzle A clogging up in the nozzle causes a pump pressure which is too high. This is why cleaning is required immediately. 1. Stop the machine and dis- connect the nozzle. 2. Clean the nozzle. IMPOR- TANT: The cleaning tool (11) should only be used when the nozzle is detached! 3. Flush the nozzle backwards with water. 7.3 Cleaning of machine vents The machine should be kept clean so as to let cooling air 7.4 Greasing of couplings To ensure easy connection and that o-rings do not dry up, the pass freely through the ma- chine vents. couplings should be greased regularly.
Page: 14
15 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 8 Trouble-shooting Please ensure that you check the following before contacting the Nilfisk service organization: Symptom Cause Recommended action Machine refuses to start Machine not plugged in Plug in machine. Defective socket Try another socket. Fuse has blown Replace fuse. Switch off other machines. Defective extension cable Try without the extension cable. Fluctuating pressure Pump sucking air Check that hoses and connections are air- tight. Valves dirty, worn out Clean and replace or refer to local Nilfisk or stuck distributor Pump seals worn out Clean and replace or refer to local Nilfisk distributor. Motor busses Low voltage or Activate the trigger of the spray handle. low temperature Machine stops Fuse has blown Replace fuse. Switch off other machines. Incorrect mains voltage Check that the mains voltage corresponds to specification on the model tag. Thermal sensor activated Leave the washer for 5 minutes to cool down. Nozzle partially blocked Clean the nozzle (see section 7.2) Fuse blows Fuse too small Change to an installation higher than the amp. consumption of the machine. You may try without the extension cable. Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until regular working pressure resumes. Inadequate supply of Check that the water supply corresponds to mains water specifications required (see model tag) NB! Avoid using long, thin hoses (min. 1/2") Nozzle partially blocked Clean the nozzle (see section 7.2) Water filter blocked Clean the filter (see section 7.1) Hose kinked Straighten out hose. Machine often starts Pump/spray handle is Contact your nearest Nilfisk Service and stops by itself leaking Centre. Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw. no water comes out frozen No water supply Connect inlet water. Water filter blocked Clean the filter (see section 7.1) Nozzle blocked Clean the nozzle (see section 7.2) Pump pressure drops Button for regulation of Adjust the button to correct working pres- (P 160.2 PLUS X-TRA) pressure / water volume not sure. correctly adjusted In case problems other than the above occur, please contact your local Nilfisk distributor. UK: Customer Services at Penrith - 01768 868995
Page: 15
16 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 9 Further information 9.1 Recycling the washer Make the old cleaner unusable immediately. 1. Unplug the cleaner and cut the electric cable. Do not discard electrical appli- ances with household waste. As specified in European Direc- tive 2002/96/EC on old electri- cal and electronic appliances, used electrical goods must be collected separately and recycled ecologically. Contact your local authorities or your nearest dealer for further information. 9.2 Warranty conditions Nilfisk guarantees high pres- sure washers for domestic use for 2 years. If your high pres- sure washer or accessories are handed in for repair, a copy of the receipt must be enclosed. Guarantee repairs are being made on the following condi- tions:  that defects are attributable to flaws or defects in materi- als or workmanship. (wear and tear as well as misuse are not covered by the guar- antee).  that the directions of this instruction manual have been thoroughly observed.  that repair has not been car- ried out or attempted by oth- er than Nilfisk-trained service staff.  that only original accessories have been applied.  that the product has not been exposed to abuse such as knocks, bumps or frost.  that only water without any impurities has been used.  that the high pressure wash- er has not been used for rental nor used commercially in any other way. Repairs under this guarantee include replacement of defec- tive parts, exclusive of packing and postage/carriage. Besides, we refer to your national law of sale. The machine should be for- warded to one of the service centres of the Nilfisk organisa- tion with description/specifica- tion of the fault. Repairs not covered by the guarantee conditions will be invoiced. (I.e. malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruction manual).
Page: 16
17 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 9.3 Accessories Only use original accessories. Brush For cars and other surfaces. Extension hose 7 m extension hose increasing the working range. Underchassis spray lance Special spray lance for washing your car underneath. Drain & Tube cleaner 15 m long tube cleaner for the cleaning of tubes and drains. Water-sand- blasting equip- ment For removal of paint and rust. Sand available from do-it-your- self shops. Patio Plus Equipment for quick cleaning of patio/drive/flagstones. Garden brush Rotating brush for cleaning of wooden surfaces. Rim brush Rotating brush for cleaning of wheel rims. Wall hook For suspension of your high pressure washer on the wall. Water suction kit For removal of large amounts of water from e.g. garden pounds. Rotary brush For cleaning vehicles and other surfaces. Roof cleaner For removal of coatings on roofs, walls, greenhouses, etc. With optional brush for cleaning of caravans, trailers, windows, etc.
Page: 17
18 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions Detergents Stone & Wood Cleaner For flagstones, brick- and woodwork. Suitable for moss and algae. Plastic Cleaner For plastic and synthetic materials such as garden furniture. Metal Cleaner For cleaning of metal such as garden tools. Car Combi Cleaner For cars etc. With rinsing wax. Alu Cleaner For surfaces of aluminium. Applied with an atomizer. Oil & Grease Cleaner For cleaning of grease and oil on motors for instance. Applied with an atomizer. Wood Cleaner For cleaning of wooden surfaces incl. of wooden garden furniture. Roof Cleaner For removal of coatings on roofs, walls, greenhouses, etc.
Page: 18
19 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions Type P 130.2 P 150.2 P 160.2 Electrical Specification Rated voltage V 230 230 230 Rated frequency Hz 50 50 50 Rated power consumption kW 2,300 2,900 3,300 Current A 10.0 12.6 14.5 Protection class Class I/ Class II Class I Class I Class I Protection degree IP xx IPX5 IPX5 IPX5 Hydraulic specification Rated pressure MPa/bar 12/120 14/140 15/150 Max. pressure MPa/bar 13/130 15/150 16/160 Rated water flow l/min/l/h 7.8/470 9.0/540 9.5/570 Max. water flow l/min/l/h 8.6/520 10.2/610 10.8/650 Max. water inlet pressure Mpa/bar 1/10 1/10 1/10 Max. water inlet temperature °C 60 60 60 Max. water inlet temp. suction mode °C 20 20 20 Weight kg 27.2 26.0 27.2 Hand-arm vibration according to ISO 5349-1: Standard nozzle m/s2 < 2.5 ±1 < 2.5 ±1 < 2.5 ±1 Sound pressure level LpA in accordance with ISO 3744 dB(A) 80 ±3 80 ±3 80 ±3 Guaranteed sound power level LWA in accordance with 2000/14/EC dB(A) 91 92 94 10 Technical Data
Page: 19
20 Nilfisk P 130.2 / P 150.2 / P 160.2 EN Original instructions 11 EU Declaration of Conformity EU Declaration of Conformity Product: High Pressure Washer Type: Nilfisk P 130.2, P 150.2, P 160.2 and accessory variants of above-mentioned types The design of the unit corresponds to the following pertinent regulations: EC Machine Directive 2006/42/EC EC Low-voltage Directive 2006/95/EC EC EMC Directive 2004/108/EC RoHS Directive 2011/65/EC EC Noise Emission directive 2000/14/EC Applied harmonised standards: EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 EN 60335-2-79:2009 EN 62233:2008 Applied international standards and technical specifications: IEC 60335-1:2001 + A1:2004 + A2:2006 IEC 60335-2-79:2002 + A1:2004 + A2:2007 Name and address of the person autho- rised to compile the technical file: Anton Sørensen General Manager, Technical Operations EAPC Nilfisk-Advance A/S Sognevej 25 DK-2605 Brøndby Identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer: Anton Sørensen General Manager, Technical Operations EAPC Nilfisk-Advance A/S Sognevej 25 DK-2605 Brøndby Place and date of the declaration Hadsund, 12.11.2013
Page: 20
http://www.nilfisk.com HEAD QUARTER DENMARK Nilfisk-Advance Group Sognevej 25 DK-2605 Brøndby Tel.: (+45) 4323 8100 E-mail: mail.com@nilfisk-advance.com SALES COMPANIES AUSTRALIA Nilfisk-Advance 48 Egerton St. P.O. Box 6046 Silverwater, N.S.W. 2128 Website: www.nilfisk.com.au AUSTRIA Nilfisk-Advance GmbH Metzgerstrasse 68 5101 Bergheim bei Salzburg Website: www.nilfisk.at BELGIUM Nilfisk-Advance n.v-s.a. Riverside Business Park Boulevard Internationalelaan 55 Bâtiment C3/C4 Gebouw Bruxelles 1070 Website: www.nilfisk.com CHILE Nilfisk-Advance de Chile San Alfonso 1462 Santiago Website: www.nilfisk.com CHINA Nilfisk-Advance (Suzhou) Building 18, Suchun Industrial Estate Suzhou Industrial Park 215021 Suzhou Website: www.nilfisk-cs.com CZECH REPUBLIC Nilfisk-Advance VGP Park Horní Počernice Do Čertous 1/2658 193 00 Praha 9 Website: www.nilfisk.com DENMARK Nilfisk-Advance NORDIC A/S Sognevej 25 2605 Brøndby Tel.: (+45) 4323 4050 E-mail: kundeservice.dk@nilfisk.com FINLAND Nilfisk-Advance Oy Ab Koskelontie 23 E 02920 Espoo Website: www.nilfisk.fi FRANCE Nilfisk-Advance 26 Avenue de la Baltique Villebon sur Yvette 91978 Courtabouef Cedex Website: www.nilfisk.fr GERMANY Nilfisk-ALTO eine Marke der Nilfisk-Advance GmbH Guido-Oberdorfer-Straße 2-10 89287 Bellenberg Website: www.nilfisk.de GREECE Nilfisk-Advance A.E. Αναπαύσεως 29 Κορωπί Τ.Κ. 194 00 Website: www.nilfisk.gr HOLLAND Nilfisk-Advance Versterkerstraat 5 1322 AN Almere Website: www.nilfisk.nl HUNGARY Nilfisk-Advance Kereskedelmi Kft. II. Rákóczi Ferenc út 10 2310 Szigetszentmiklos-Lakihegy Website: www.nilfisk.hu INDIA Nilfisk-Advance India Limited Pramukh Plaza, ‘B’ Wing, 4th floor, Unit No. 403 Cardinal Gracious Road, Chakala Andheri (East) Mumbai 400 099 Website: www.nilfisk.com IRELAND Nilfisk-Advance 1 Stokes Place St. Stephen’s Green Dublin 2 Website: www.nilfisk.com ITALY Nilfisk-Advance SpA Strada Comunale della Braglia, 18 26862 Guardamiglio (LO) Website: www.nilfisk.it JAPAN Nilfisk-Advance Inc. 1-6-6 Kita-shinyokohama, Kouhoku-ku Yokohama, 223-0059 Website: www.nilfisk.com MALAYSIA Nilfisk-Advance Sdn Bhd Sd 14, Jalan KIP 11 Taman Perindustrian KIP Sri Damansara 52200 Kuala Lumpur Website: www.nilfisk.com MEXICO Nilfisk-Advance de Mexico, S. de R.L. de C.V. Agustín M. Chavez No. 1, PB oficina 004 Col. Centro de Ciudad Santa Fe 01210 Mexico, D.F. Website: www.nilfisk.com NEW ZEALAND Nilfisk-Advance Danish House 6 Rockridge Avenue Penrose, Auckland 1135 Website: www.nilfisk.com NORWAY Nilfisk-Advance AS Bjørnerudveien 24 1266 Oslo Tel.: (+47) 22 75 17 70 E-mail: info.no@nilfisk.com POLAND Nilfisk-Advance Sp. Z.O.O. ul. 3 Maja 8 05-800 Pruszków Website: www.nilfisk.pl PORTUGAL Nilfisk-Advance Sintra Business Park Zona Industrial Da Abrunheira Edificio 1, 1° A P2710-089 Sintra Website: www.nilfisk.pt RUSSIA Нилфиск-Эдванс 127015 Москва Вятская ул. 27, стр. 7 Россия Website: www.nilfisk.ru SOUTH AFRICA WAP South Africa 12 Newton Street Spartan 1630 Website: www.nilfisk.com SOUTH KOREA Nilfisk-Advance Korea 3F Duksoo B/D, 317-15 Sungsoo-Dong 2Ga, Sungdong-Gu Seoul Website: www.nilfisk.com SPAIN Nilfisk-Advance S.A. Torre d’Ara, Planta 9 08302 Mataró Barcelona Website: www.nilfisk.es SWEDEN Nilfisk-Advance AB Taljegårdsgatan 4 431 53 Mölndal Website: www.nilfisk-alto.se SWITZERLAND Nilfisk-Advance Ringstrasse 19 Kircheberg/Industri Stelzl 9500 Wil Website: www.nilfisk-alto.ch TAIWAN Nilfisk-Advance Taiwan Branch 1F, No. 193, sec. 2, Xing Long Rd. Taipei Tel.: (+88) 6227 002 268 Website: www.nilfisk-alto.tw THAILAND Nilfisk-Advance Co. Ltd. 89 Soi Chokechai-Ruammitr Viphavadee-Rangsit Road Ladyao, Jatuchak, Bangkok 10900 Website: www.nilfisk-thailand.com TURKEY Nilfisk-Advance A.S. Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7 Ümraniye Istanbul Website: www.nilfisk.com UNITED KINGDOM Nilfisk (A Division of Nilfisk-Advance Ltd.) Bowerbank Way Gilwilly Industrial Estate, Penrith Cumbria CA11 9BQ Tel: 01768 868995 Website: www.nilfisk.co.uk UNITED ARAB EMIRATES Nilfisk-Advance Middle East Branch SAIF-Zone P.O. Box 122298 Sharjah Website: www.nilfisk.com VIETNAM Nilfisk-Advance Representative Office No. 51 Doc Ngu Str. Ba Dinh Dist. Hanoi Website: www.nilfisk.com

Question & answers

Hi I work at a pool and the Nilfisk We use leaks, a lot. Which means the water pressure is very low and quite useless. It pours water out of the "gun" every time I turn it on what should I do?

Magdalena, 2017-07-31 14:11:32

Have a question about the Nilfisk P 150.2 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Nilfisk P 150.2. Please make sure that you describe your difficulty with the Nilfisk P 150.2 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Nilfisk P 150.2

Name
Email
Reaction

View a manual of the Nilfisk P 150.2 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Nilfisk
  • Product: Pressure washers
  • Model/name: P 150.2
  • Filetype: PDF
  • Available languages: Dutch, English, Finnish, French