Nilfisk GU 15 SMU manual

User manual for the Nilfisk GU 15 SMU in Dutch. This PDF manual has 92 pages.

Page: 1
823 0102 000 Edition P02 INSTRUCTIONS FOR USE BRUKSANVISNING BRUGSANVISNING KÄYTTÖOHJE MODE D’EMPLOI BEDIENUNGSANLEITUNG INSTRUCCIONES DE USO ISTRUZIONI PER L’USO INSTRUÇÕES DE MANEJO GEBRUIKSAANWIJZING Printed in China GU 305, GU 355, GU 355-DUAL, GU 455-DUAL GU 12 SMU, GU 15 SMU GU 12 DMU, GU 15 DMU, GU 18 DMU 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 1 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 1 2008-04-17 09:36:03 2008-04-17 09:36:03
Page: 2
2 English___________ 3-11 Svenska_________ 12-19 Deutsch__________ 20-27 Nederlands_______ 28-35 Suomi___________ 36-43 Dansk___________ 44-51 Français_________ 52-59 Italiano__________ 60-67 Espańol__________ 68-75 Portuguęs________ 76-83 Norsk____________ 84-91 www.nilfisk.com 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 2 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 2 2008-04-17 09:36:29 2008-04-17 09:36:29
Page: 3
3 For more information visit our website: www.nilfisk.com Model GU 305, GU 355, GU 12 SMU, GU 15 SMU GU 355-DUAL, GU 455-DUAL, GU 12 DMU, GU 15 DMU GU 18 DMU Voltage V/Hz 220-240/50-60 110-120/50-60 220-240/50-60 110-120/50-60 Rated Power W 1000 1200 Protection class (electrical) II II Sound Pressure Level dB(A) 69 69 Total weight Kg 7.7 8.5 TECHNICAL SPECIFICATION (as installed and tested on the unit) INTRODUCTION This manual will help you get the most from your vacuum cleaner. Read it thoroughly before operating the machine. This product is intended for commercial use. PARTS AND SERVICE Repairs, when required, should be performed by your Authorized Service Center, who employs factory trained service personnel, and maintains an inventory of original replacement parts and accessories. Please specify the Model and Serial Number when discussing your machine. RATING PLATE The Model Number and Serial Number of your machine are shown on the rating plate on the machine. This information is needed when ordering spare parts for the machine. Use the space below to note the Model Number and Serial Number of your machine for future reference. MODEL NUMBER____________________________________ SERIAL NUMBER ___________________________________ UNPACKING THE MACHINE When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected. The symbol on the product or on its packing indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 3 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 3 2008-04-17 09:36:29 2008-04-17 09:36:29
Page: 4
4 GU 305, GU 355, GU 355-DUAL, GU 455-DUAL is designed, developed and rigorously tested to function efficiently and safely when properly maintained and used in accordance with the fol- lowing instructions. These instructions have been prepared with safety and efficiency paramount. The MACHINE OPERATOR must be trained by a suitably quali- fied instructor, and be made aware of the relevant regulations and legislation currently in force at the time of use. CAUTION - This machine MUST NOT be used in explosive or inflammable atmospheres or where such atmospheres are likely to be produced by the presence of volatile liquid or inflammable gas or vapour. CAUTION - In no circumstances should the power supply cord be wrapped around fingers or any part of the operators person. CAUTION - The electrical supply plug must not be subjected to undue stress by pulling on the power supply cord. Your MACHINE must only be connected to an electrical supply of the same voltage and frequency as indicated on the rating plate. Ensure that the plug fitted to the end of the power supply cord is suitable for your supply socket, if not refer to the information con- tained in ’Electrical Connections’, or consult a qualified electrician. The electrical installation from which the supply is drawn must be maintained to current Institute of Electrical Engineers wiring regulations. REGULAR SERVICING and INSPECTION of your machine must be carried out by suitably qualified personnel in accordance with relevant legislation and regulations. In particular, electrical tests for earth continuity, insulation resistance, and condition of the flexible cord should be checked frequently. In the event of any defect the machine MUST be withdrawn from service, completely checked and repaired. Trained Service Engineers will be pleased to carry out on site ser- vicing on a regular or as requested basis, to ensure the continuing safety and efficiency of your machine. PLEASE READ THESE ESSENTIAL INSTRUCTIONS (Only applicable to UK) DOUBLE-INSULATED MACHINES IMPORTANT 240 volt 50 Hz. machines are fitted with a 13 amp. 3 pin moulded plug. the plug is fitted with a 13 amp. detachable fuse. The correct replacement for the fuse is identified by marking or colour coding. Only fuses that are ASTA approved to BS 1362 should be fitted. Never use the plug without the fuse cover fitted. Replacement fuse covers are available at any electrical retail outlet. If the available socket outlet is not suitable for the plug supplied, the plug must be cut off and an appropriate plug fitted. The plug thus cut off MUST BE DESTROYED for safety reasons before being disposed of. Machines built for other voltages and frequencies are not normally supplied with a fitted plug. If it is necessary to fit a plug, the wires in this power supply cord are coloured in accordance with the following code: BLUE-NEUTRAL BROWN-LIVE TO CONNECT THE NEW PLUG: Ifusingathree-pinplug,donotmakeanyconnectiontothetheterminal in the plug which is marked with the letter ‘E’ or by the safety earth symbol or coloured green or green & yellow. This machine is double-insulated and no earth connection is necessary. The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter ‘N’ or is coloured black or blue. The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter ‘L’ or is coloured red or brown. If the plug to be fitted does not conform to the above notation then consult a qualified electrician. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 4 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 4 2008-04-17 09:36:29 2008-04-17 09:36:29
Page: 5
5 • Caution: Do not use this appliance for vacuuming dust which may be considered hazardous to health. • Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present. • Do not allow it to be used as a toy. Close attention is necessary when used near children. • Do not use unless filters and dustbag are fitted. • If the cleaner is not working properly or has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or dealer. • Use only as described in this manual and only with the manufacturer’s recommended attachments. • BEFORE YOU PLUG IN YOUR CLEANER, check the rating plate to see if the rated voltage agrees within 10% of the voltage available. • This appliance is provided with double insulation. Use only identical replacement parts. See instructions for servicing of double insulated appliances. SERVICING DOUBLE-INSULATED APPLIANCES In a double-insulated appliance, two systems of insulation are provided instead of earthing. No earthing means is provided on a double-insulated appliance, nor should a means for earthing be added to the appliance. Servicing a double-insu- lated appliance requires extreme care and knowledge of the system, and should be done only by qualified service per- sonnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace.Adouble insulated appliance is marked with the words ”DOUBLE INSULATION” or ”DOUBLE INSULATED.” The symbol (square within a square) may also be used on the product. This appliance conforms with EC-Directive CEE 73/23, CEE 93/68, CEE 89/336. SAVE THESE INSTRUCTIONS This vacuum cleaner is to be used for commercial use. Accidents due to misuse can only be prevented by those using the machine. When using an electrical app- liance, basic precautions should always be followed, including the following: Never use the machine on wet surfaces. Read and follow all safety instructions. To reduce the risk of fire, electric shock, or injury, please read and follow all safety instructions and caution markings before use. This vacuum cleaner is designed to be safe when used to for cleaning functions as specified. Should damage occur to electrical or mechanical parts, the cleaner and / or ac- cessory should be repaired by the manufacturer or com- petent service station before use in order to avoid further damage to the machine or physical injury to the user. • Do not use outdoors or on wet surfaces. • Disconnect the cleaner before servicing and when not in use. Do not leave the cleaner plugged in unattended. • Do not use with damaged cord or plug. To unplug grasp the plug, not the cord. Do not handle plug or cleaner with wet hands. Turn off all controls before unplugging. • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run cleaner over cord. Keep cord away from heated surfaces. • This machine creates and containes a revolving brush roll. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts. Do not put any objects into openings or use with opening blocked. Keep openings free from dust, lint, hair, and anything else that could reduce the flow of air. • Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. • Use extra care when using on stairs. • This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children must be supervised not to play with the appliance. WARNING! Never attempt to vacuum liquid, glass fragments or ashes! Wet surfaces can expose the operator to possible electrical shock. IMPORTANT SAFEGUARDS 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 5 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 5 2008-04-17 09:36:29 2008-04-17 09:36:29
Page: 6
6 1 2 2 3 4 6 7 8 9 10 11 13 14 5 15 16 17 18 19 20 21 2 KNOW YOUR MACHINE As you read this manual, you will occasionally run across a bold number in parentheses - example: (2). These numbers refer to an item shown on this page. Refer back to this page whenever necessary, to pinpoint the location of an item mentioned in the text. 1 Handle 2 Cord Hook 3 Vacuum Hose 4 Handle Lock Button 5 Dust lid 6 Carrying Handle 7 Light, Green - Only Double Motor Unit (DUAL-versions) 8 Light, Red Only Double Motor Unit (DUAL-versions) 9 Brush Housing 10 Brush Height Adjustment Knob 11 Pedal 13 Wand 14 Crevice Tool 15 “Dust Bag Full” Indicator 16 Dust lid button 17 Main Power Switch 18 Exhaust Filter Cover 19 Filter Cover Latch 20 Power Cord Clamp 21 Upholstery Tool SET UP AND ASSEMBLY 1. Carefully take out the vacuum cleaner from its carton. 2. Push the Handle (1) into the opening at the top of the Dust compartment until the button at the rod snaps in place and secure the handle to the housing. Never operate the vacuum cleaner without a Dust Bag in place. These machines are equipped with an "no bag" clip. This means that if a dust bag not is fitted or fitted uncorrectly - the dust lid (5) would not be able to close. Insert the handle at the opening at the top of the bag housing, until the button at handle snaps in place. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the release mechanism. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 6 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 6 2008-04-17 09:36:30 2008-04-17 09:36:30
Page: 7
7 4 5 5 6 1 2 1 3 OPERATING THE VACUUM CLEANER 1. Release the power cord from the cord hooks (2) at the backside of the vacuum cleaner. Turn the lower hook so that the cord is released. Unwind the whole power cord . 2. Adjust the height of the handle, by pushing at the handle lock button (4) and then pull or push at handle to comfortable height. 3. Add the cord to the hook of the handle in order to make an anti strain function. Then plug-in the power cord into a electrical outlet. 4. Turn the Main Power Switch (17) ON. “l” is ON and “O” is OFF. Now the vacuum motor will start. 5. Step on the Pedal (11) and then tilt the cleaner backwards. Now the brush motor will start (DUAL-versions only). At DUAL-versions the green light (7) at the brush housing (9) will come on to indicate that the brush motor is running. On single-motor versions, the brush is always turning when on. 6. Turn the Height Adjustment Knob (10) to adjust the height that the brush will operate in - depending on the material at the surface to be vacuumed. For carpets with short textiles the brush should in the lower position. Turn the knob to the left (when you are placed in front of the machine) to lower the brush. For carpets with longer textiles the brush should in a higher position. Turn the knob to the right (when you are placed in front of the machine) to set the brush at a higher level. If the red light comes on, slowly turn the knob in the opposite direction until the light goes off (Dual-versions only). If the red light (8) stays on continuously, there may be debris wrapped around the brush, during operation. On double motor units this can cause the overload protector for the brush motor to trip. If this occurs, turn the Main Switch (17) OFF and unplug the power cord. Remove any debris from the brush and plug in the power cord, turn the Main Switch (17) back ON. This will automatically reset the overload protector. If the overload protector trips repeatedly contact your dealer for service. For more information of the light indicators on the DUAL-versions - see the table below. NOTE! Always disconnect the power cord before performing any machine maintenance. Change the bag whenever the “Bag Full” indicator (15) comes on. For details of dust bag replacement see separate instruction in this manual. If the light comes on before the bag is full, the inside of the bag may be coated with very fine dust (change the bag), or debris may be built up somewhere between the brush and the bag. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. Lower Lower Higher Higher On - Off On - Off LIGHT INDICATION AND FUNCTION FOR THE BRUSH MOTOR (DUAL - Double Motor Units only!) GREEN RED CONDITION FUNCTION 1. ON OFF Normal operation In normal operation, the green light is constantly illuminated. 2. OFF ON - BLINKING Brush position too low (heavy loading) 1. If the condition 2, red light blinking, continues for 10 seconds or more, the control module will cut out the power supply to the brush motor. 2. The red light will still be illuminated until you turn off the switch or unplug the cord. 3. OFF ON Brush stalled 1. The red light will be constantly illuminated and the control module will instantly cut the power supply to the brush motor, if the brush was stalled accidentally. 2. The red light will still be illuminated until you turn off the switch or unplug the cord. Release Release base base 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 7 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 7 2008-04-17 09:36:30 2008-04-17 09:36:30
Page: 8
8 1 2 1 2 3 3 USING THE WAND (OPTIONAL) The Wand (13) is not supplied as a standard item in all variants of these machines. To use the wand: 1. Push the machine to upright locked position. The brush motor will then stop (DUAL-version only), and the brush will be lifted up from the surface on single motor-versions. Then slide the Wand out of its holder. 2. Use the wand for cleaning hard to reach places like floor corners, or furnitures. USING THE TOOLS (OPTIONAL) These tools are not standard items in all machine variants. Use these tools for a better cleaning performance at hard to reach areas. A Crevice Tool (14) and Upholstery Tool (21) is placed comfort- able on the machine, just behind the wand. Remove the wand from the vacuum cleaner and you will have free access to the Tools. 1. The Upholstery Tool is placed in the upper section of the cleaner. 2. The crevice tool is placed in the lower section of the cleaner. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. 3. Install the Crevice Tool or Upholstery Tool on the end of the Wand, or on the end of the hose, which can be detached from the wand, if desired. Now the vacuum cleaner will have an extended coverage performance and can be used for cleaning hard to reach areas like roof strips, or furnitures. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 8 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 8 2008-04-17 09:36:32 2008-04-17 09:36:32
Page: 9
9 1 2 1 2 3, 4 5 5 6 3 3 4 4 CHANGING THE PAPER DUST BAG Change the bag whenever the “Bag Full” (15) indica- tor comes on. To replace the Paper Dust Bag: 1. Disconnect the power cord from the electrical outlet. Pull the Dust lid button (16) and remove the Dust lid outwards to remove it from the cleaner. 2. Push downwards at the edge to the left of the plastic holder, so that the bag loosens from the vacuum inlet of the machine. 3. Grasp at the cardboard piece of the bag and gently pull the full bag outwards - away from cleaner. 4. Insert a new paper dust bag into the slot of the bag holder and push the bag in place. Check so that the paper dust bag not is jammed in the holder.Only the cardboard piece of the bag should be attached to the bag holder. 5. Push the bag holder with the new bag upwards, so that the bag inlet fastens to the inlet of the machine. Make sure that the bag is unfold and will fit in place in the bag housing. Also check that the ”no bag” clip is placed to the left so that the lid will be able to close. 6. Fit the two notches of the back cover to the two slots at the lower part of the bag housing, and push the back cover back in place at the housing. EMPTYING THE CLOTH DUST BAG Empty the Bag whenever the “Bag Full” Light (15) comes on. To empty or to replace: 1. Disconnect the power cord from the electrical outlet. Pull the Dust lid button (16) and drag the Dust lid outwards to remove it from the cleaner. 2. Push downwards at the edge to the left of the plastic holder, so that the bag inlet loosens from the vacuum inlet of the machine. 3. Grasp at the plastic flange of the bag and gently pull the bag outwards - away from cleaner. 4. Remove bag clip and shake out bag contents. 5. Put the bag clip back on the bag. 6. Insert the cleaned/new cloth bag into the slot of the bag holder and push the bag in place so that bag is secured. 7. Push the bag holder with the new bag upwards, so that the bag inlet fasten to the inlet of the machine. Make sure that the bag is unfold and will fit in place at the bag housing. Also check that the ”no bag” clip is placed to the left so that the lid will be able to close. 8. Fit the two notches of the back cover to the two slots at the lower part of the bag housing, and push the back cover back in place at the housing. MAINTENANCE NOTE! Photos belows shows changing of the paper dust bags! Never operate the machine without a Dust Bag in place. Always disconnect the power cord before performing any machine maintenance. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 9 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 9 2008-04-17 09:36:33 2008-04-17 09:36:33
Page: 10
10 1 2 3 4 2 3 4 6 7 1. Disconnect the power cord from the electrical outlet. Push the Filter Cover Latch (19) downwards so that the cover (18) is released. Remove the filter cover from cleaner. 2. Grasp at the filter frame and remove the used and dirty HEPA-filter 3. Grasp at the filter frame and then insert the new HEPA filter to the cleaner by pushing it in place. Never touch the filter media at a HEPA-filter! Doing so may cause a loss of performance of the HEPA-filter). 4. Snap the Filter Cover back in place at the cleaner. IMPORTANT! Never operate the cleaner without the HEPA-Filter in place in the machine. Note! These machines are not designed for picking up hazardous - i.e. poisonous dust! FILTERS - type of filter may vary from different models On these machines there are two different filters; one pre-filter before the vacuum motor and one exhaust filter. There are two different types of exhaust filters available to these machines, HEPA-filter and a standard exhaust filter. The HEPA-filter (High Efficiency Particulate Air filter) offers better filtration capacity then the standard exhaust filter. The exhaust filters catches any dirt that may escape from the dust bag, or motor pre filter. Replace the filter every fourth time that the dust bag is changed (more often in very dusty applications). The exhaust filters are located at the front side of the machine just above the brush base. The HEPA filter can not be cleaned or washed clean. When the HEPA-filter is clogged it must be replaced. 1. Unplug the power cord from the electrical outlet. 2. Release the brush roller by unlocking the bearing block. Push the button backwards left towards the unlocking symbol at the brush housing. 3. Grasp at the bearing block and pull it out from the brush housing. 4. Remove the used brush. 5. Replace the used brush roller with a new one, or clean and remove all debris from the present brush. 6. Slide back the brush into the the fixed bearing block in the brush house. 7. Push the bearing block in its position. Lock it by turning clockwise. CHANGING THE HEPA-FILTER CHANGING OR CLEANING OF THE BRUSH Always disconnect the power cord before performing any machine maintenance. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 10 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 10 2008-04-17 09:36:34 2008-04-17 09:36:34
Page: 11
11 1 2 1 2 3 5 3 4 The pre filter catches any dirt spilled from the bag, before it can enter the vacuum motor. The filter is located below the bag. Clean the filter every third time that the bag is changed (more often in very dusty applications). To clean/replace the Pre Filter. 1. Disconnect the power cord from the electrical outlet. Then push the Dust lid button (16) in and remove the dust lid (5). 2. Grasp at the filter holder and pull the holder out from the Dust compartment. 3. Remove the dirty filter from the filter holder and replace with a new pre filter. The pre filter may also be washed. Wash it in warm water. Let the filter dry completely before putting it back into the filter holder. 4. This machine is also equipped with a deodorizer pad (an anti smell). It´s a located in the pre filter holder. Replace it to a new deodorize pad when the function begins to fade. 5. Put back the new/washed filter into the holder. Then put back the holder with filter in place in the bag housing. 6. Fit the two notches of the back cover to the two slots at the lower part of the bag housing, and push the back cover back in place at the housing. IMPORTANT ! Never operate the machine without the pre-filter in place. 1. Disconnect the power cord from the electrical outlet. Push the Filter Cover Latch (19) downwards so that the Filter Cover (18) is released. 2. Remove the cover with the filter, from the cleaner. 3. Remove the used and dirty exhaust filter. 4. Insert a new exhaust filter to the filter cover. 5. Snap the Filter Cover back in place on the cleaner. CHANGING THE EXHAUST FILTER 1. Unplug the Power Cord from the electrical outlet. 2. If the Dust Bag Full” Indicator (15) not has been lightened during operation - the dust bag still has filling capacity. Open the dust housing cover to ensure that the dust bag is not full, replace if necessary. See also separate instructions for replacing the dust bag. Clean the bag housing, if necessary. 3. Wind up the cord (starting from the machine inlet side). 4. Store the cord at the hook at the Dust lid cover and the hook at the handle. 5. Check the brush house. Remove any built-up carpet fibers or debris from the brush and the brush housing. 6. Store the machine indoors in a clean, dry place. CLEANING OR CHANGING THE PRE FILTER AFTER USING THE MACHINE IMPORTANT ! Never operate the machine without the Exhaust Filter in place at the machine. 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 11 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 11 2008-04-17 09:36:35 2008-04-17 09:36:35
Page: 12
92 www.nilfisk.com 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 92 823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 92 2008-04-17 09:37:44 2008-04-17 09:37:44

Question & answers

Have a question about the Nilfisk GU 15 SMU but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Nilfisk GU 15 SMU. Please make sure that you describe your difficulty with the Nilfisk GU 15 SMU as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Nilfisk GU 15 SMU

Name
Email
Reaction

View a manual of the Nilfisk GU 15 SMU below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Nilfisk
  • Product: Vacuum Cleaners
  • Model/name: GU 15 SMU
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Swedish, Portuguese, Danish, Norwegian, Finnish