E 130.2-9 PAD X-TRA

Nilfisk E 130.2-9 PAD X-TRA manual

E 130.2-9 PAD X-TRA

User manual for the Nilfisk E 130.2-9 PAD X-TRA in English. This PDF manual has 19 pages.

Page: 1
Copyright © 2011 Nilfisk, Division of Nilfisk-Advance A/S
Page: 2
3 Index 1 Safety precautions and warnings .............................................3 2 Description ...............................................................................4 3 Before you start using your pressure washer...........................5 4 Operating your pressure washer ..............................................6 5 Fields of Application and Working Methods.............................................................10 6 After using your pressure washer...........................................12 7 Maintenance...........................................................................13 8 Trouble Shooting ....................................................................14 9 Further information.................................................................15 10 EC Declaration of Conformity.................................................17 1 Safety Precautions and Warnings Before starting up your high-pres- sure washer for the first time, this instruction manual must be read through carefully. Save the instructions for later use. Safety instructions marked with this symbol must be observed to pre- vent danger to persons. This symbol is used to mark safety instruc- tions that must be observed to prevent damage to the machine and its performance. This symbol indicates tips and instructions to simplify work and to ensure a safe operation. Do not let children or people who have not read the instruc- tion manual operate the ma- chine. Before starting up your machine please check it carefully for any defects. If you find any, do not start up your machine and con- tact your Nilfisk distributor. Especially check: The insulation of the electric cable should be faultless and without any cracks. If the electric cable is damaged, an authorized Nilfisk distributor should replace it. WARNING! High pressure jets can be dangerous. Never direct the water jet at persons, pets, live electrical equipment or the machine itself. Never try to clean clothes or footwear on yourself or other persons. Hold the spray lance firmly with both hands. The spray lance is affected by a thrust of up to 16.4 N during ope- ration. The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation. Wear goggles during opera- tion. Never use the machine in an environment where there could be a danger of explo- sion. If any doubt arises, please contact the local authorities. It is not allowed to clean asbestos-containing surfaces with high pressure. This high pressure washer must not be used at tempe- ratures below 0°C. Never let any persons stay under the product when stored on the wall. WARNING! Inadequate extension cables can be dangerous. Cables on drums should always be com- pletely unwinded to prevent the cable from overheating. Symbols used to mark in- structions
Page: 3
4 Extension cables should be of a watertight construction and comply with the below-men- tioned requirements for length and cable dimensions. 1.0 mm² max. 12.5 m 1.5 mm² max. 20 m 2.5 mm² max. 30 m Cable connections should be kept dry and off the ground. Mains power connection The following should be ob- served when connecting the high pressure washer to the electric installation: Only connect the machine to an installation with earth con- nection. The electric installation shall be made by a certified elec- trician. It is strongly recommended that the electric supply to this machine should include a re- sidual current device (GFCI). Water connection Connection to the public mains according to regu- lations. This high pres- sure washer is only allowed to be connected with the drinking water mains, when an appro- priate backflow preventer has been installed, Type BA accord- ing to EN 1717. The backflow preventer can be ordered under number 106411177. The length of the hose between the back- flow preventer and the high pressure washer must be at least 10 metres to absorb pos- sible pressure peaks (min diam- eter ½ inch). Operation by suction (for ex- ample from a rainwater vessel) is carried out without backflow preventer. Recommended suc- tion set: 126411387. As soon as water has flown through the BA valve, this water is not considered to be drinking water any more. IMPORTANT! Only use wa- ter without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own well), an additional filter should be mounted. Repair and maintenance WARNING! Always remove the electric plug from the socket be- fore carrying out maintenance work on the machine. Safety devices Locking device on spray gun (7a) (see foldout at the end of this manual): The spray gun features a lock- ing device. When the pawl is activated, the spray gun cannot be operated. Thermal sensor: A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sen- sor has cooled. Pressure safety device An integrated hydraulic safety valve protects the system from excessive pressure. 2 Description This high-pressure washer has been developed for domestic use within: - Car, motorbike, boat, cara- van, trailer, patio/drive/flag- stones, woodwork, brickwork, barbecue, garden furniture, lawn mower Section 5 describes the use of the high-pressure washer for vaious cleaning jobs. Only use the high-pressure washer for purposes described in this manual. The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries. 2.1 Application
Page: 4
5 2.2 Operation elements and model survey See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet (with filter) 3 High pressure connection (only models without hose reel) 4 High pressure hose 5 Electric cable 6 Click & Clean spray lance 7 Spray gun with lock 8 Click & Clean Tornado® PR nozzle 9 Click & Clean Powerspeed® nozzle 10 Click & Clean foam sprayer 11 Nozzle cleaning tool 12 Trolley handle (telescopic handle) 13 Hose reel (not standard) 14 Hose hook 15 Model tag 16 Quick coupling 17 Button for telescopic handle 18 Turnable cable hook Specifications: See model tag (15) of machine. Sound pressure level meas- ures in accordance with ISO 3744 EEC directive 2000/14/ EEC: LpA = 69,9 dB(A), LWA = 84 dB(A). Hand/arm vibrations measured according to ISO 5349 is < 2.5 m/s2 . We reserve the right to alter the specifications. 3 Before you start using your pressure washer 3.1 Mounting of trolley handle and hose hook (standard models) 1. Push down the trolley handle (12) over the two metal tubes. Make sure that the handle is mounted as illustrated. Mount screws with nuts (make sure that the screws go through handle as well as tube). 2. Mount the hose hook (14) on the machine (2 screws). Note: the hose hook can be mounted on the front as well as on the back. Front position is to be used if the product is used together with a special wall hook for wall storage. 3.2 Mounting of hose reel handle (models with hose reel) 1. Click the hose reel handle on to the trolley handle (no screws).
Page: 5
6 3.3 Mounting of quick coupling 1. Screw the quick coupling (16) tight on to the water inlet (2). Note: The inlet filter must al- ways be fitted in the water inlet pipe to filter out sand, limestone and other impurities as these will damage the pump valves. Caution: Failure to fit the filter will invalidate the guarantee. 4 Operating your pressure washer 4.1 Connection of high pressure hose (models without hose reel) 1. Mount the high pressure hose on the outlet (3). 3.4 Mounting of high pressure hose Attach the high pressure hose (4) to the spray gun (7). De h the high pressure hose by pressing the pawl (A).
Page: 6
7 4.2 Mounting of spray lance and Click & Clean nozzles 2. Attach the nozzle. Warning: When attaching the Click & Clean nozzles, the pawl on the side of the spray lance should come out again. Note: The Tor- nado® PR noz- zle and the foam sprayer feature a swivel lock, which must be positioned in the hole in the Click & Clean spray lance. Press the pawl to detach the Click & Clean nozzle. 1. Push the spray lance (6) into the spray gun (7) and screw it on. Note: The spray lance (6) has a built-in low pressure nozzle that can be used for flushing away dirt.   4.3 Water connection An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. NOTE: Connec- tion to the public mains according to regulations. IMPORTANT! Only use wa- ter without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own well), an additional filter should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat- ing the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is not clogged up. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 50°C). 3. Turn on the water.
Page: 7
8 4.5 Start and stop of the ma- chine (when connected to a water supply) The spray lance is affected by a thrust during opera- tion - therefore always hold it firmly with both hands. IMPOR- TANT: Point the nozzle at the ground. 1. Check that the machine is in upright position. NOTE: Do not place the ma- chine in high grass! 2. Release the trigger lock. 3. Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose. 4. Turn the start/stop switch (1) to position "I". 5. Activate the trigger of the spray gun. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. Do not cover the machine during operation. Note: If the ma- chine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Turn the start/stop switch to position "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray gun. When releasing the trigger of the spray gun, the machine automatically stops. The ma- chine will start again when you re-activate the spray gun. 4.4 Telescopic handle The machine features a tele- scopic handle. To raise or lower the handle, press the knob and move the handle upwards or downwards. When a click is heard, the handle is in right position. Use an external filter if the water contains impurities. 2. Turn the start/stop switch to position "I". 3. Activate the trigger of the spray gun and let the water run, until the air has escaped from the water hose and the pump. 4. Mount spray lance and nozzle. The washer can take in water from a rain water tank as an example. The hose for the wa- ter supply must not be too long, approx. 5 m. Make sure that the water tank is not placed on a lower level than the machine. 1. Place the other end of the water hose in the water tank. 4.6 Start the machine (when connected to open con- tainers (suction mode))
Page: 8
9 4.7 Pressure regulation on the TORNADO® PR- nozzle The pressure can be regulated on the TORNADO® PR nozzle. 4.8 Stationary use If mounting a special wall hook (not standard), the pressure washer can be used as a sta- tionary solution meaning that it can be operated while hanging on the wall. Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of rawl- plugs to the type of wall. On the wall hook garden/rim brush (a) foam sprayer (b), Click & Clean brush (c) and Click & Clean nozzles (d) can be stored. Important: The bearing capacity of the wall hook is max. 30 kg. A C B D ,AVTRYK (’JTRYK High pressure Low pressure
Page: 9
10 5 Fields of application and working methods 5.1 General Efficient high presure cleaning is achieved by following a few guide- lines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly cho- sen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning. 5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid "super clean" areas, where the detergent collects in higher concentration and streams downwards. Let the detergent work for several minutes before rinsing but never let it dry on the surface be- ing cleaned. Note: It is important that the detergents do not dry up. Otherwise the surfac that has to be cleaned can be damaged. 5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical effect may be required. Special wash brushes offer this supplemen- tary effect that cuts through dirt (especially by car washing).
Page: 10
11 5.2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents. Task Accessories ‘Click & Clean’ Cleaning method Car Car nozzle, auto brush, underchassis nozzle, Foam sprayer, Car Combi Cleaner 1. Apply Car Combi Cleaner with the foam sprayer. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min. 2. Wash the car with the car nozzle, which has been optimized for quick and gentle cleaning of enamelled surfaces (the jet is wider and not so sharp). Start at the front of the car and work back- wards to avoid water from penetrating by the door mouldings. 3. Use the brush for removal of traffic film which is not removed by the nozzle. If the car is very dirty, apply Car Combi Cleaner again. 4. Attach the undercarriage nozzle and clean undercarriage and wheel arches. 5. Remove water from the surface of the car with the scraper on the car brush. Make sure that all grains of sand etc. have been removed before using the scraper. Wipe with a wash lea- ther where the scraper cannot reach. Rims, alu- minium Rim brush, auto nozzle, atomizer, Alu Cleaner Apply Alu Cleaner with an automizer. Let it act for approx. 5 min. and wash with the rim brush. For steel rims, use Car Com- bi Cleaner. Use the foam sprayer and wash with rim brush. Be careful! The high pressure jet may damage the tyres. Flag- stones, concrete floors and other hard surfaces Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Wash towards outlets or the like. On surfaces with moss or algae you may start by applying Stone & Wood Cleaner with the foam sprayer. Wash before the soap dries. Another more effective and quicker method is to use the Patio Cleaner. Thus you will also avoid splashes. Garden furniture, wood Wood Cleaner Garden brush Apply Wood Cleaner and wash before the soap dries. NOTE: Use the garden brush to clean off the dirt. Brickwork, Wood work Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Same method as for flagstones, but be careful - bad joints and wood may be damaged by high pressure.You may choose only to use the Tornado® nozzle. Adjust the distance (pressure) to the quality of the joints and the wood. Patio Cleaner can also be used on vertical surfaces. Gutter Underchassis spray lance Wash the gutter with the nozzle. Always wash towards downpipes. Beware not to spray under the roofing. Cleaning of drain pipes, out- lets, down pipes etc. Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the „plug“ and flush the dirt backwards. Rust, paint Water/sandblasting equipment Mount the water/sand blasting equipment and rust and paint is efficiently and quickly removed. Beware not to damage the surface to be sandblasted. Green- house Tornado® PR nozzle brush, Stone & Wood Cleaner Wash with high pressure and maybe a brush.You may use Stone & Wood Cleaner to remove moss and algae. Garden tools, lawn mover Tornado® PR nozzle, Power- speed® nozzle, multiangle adaptor, Metal Cleaner Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with the foam sprayer and let it act for approx. 5 min. Wash with the nozzle.You may use the multiangle adaptor for hard to get at areas to avoid splashing.
Page: 11
12 6 After using your pressure washer 6.2 Winding up of electric cable and high pressure hose carefully up. 1. Wind up the electric cable on the appropriate hooks. Built- in clip for good holding (1). The lower hook can be turned to release the electric cable. 2. The high pressure washer comes in two models: A) with hook for storage of high pres- sure hose (14) - B) with a hose reel (13). 6.1 Storing the washer The machine should be sto- red in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (turn the start/stop switch (1) to posi- tion “O” and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray gun. 3. Stop the machine, unplug and wind up hose and cable. 4. Place spray handle, nozzles and other accessories in the holders of the machine. Should the machine by mistake be frozen, it will be necessary to check it for damage. NEVER START-UP A FROZEN MACHINE. Frost damages are not covered by the guarantee! 6.3 Storage of accessories The standard accessories (spray gun (f), spray lance (a), nozzles (b) foam sprayer (c)) can be stored on the pressure washer. The nozzle cleaning tool (d) and a Click & Clean brush (e) can also be stored on the product. To avoid accidents, the electric cable and the high pressure hose should always be winded a b c d e f a + f
Page: 12
13 WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice: Wash out water hose, high pressure hose, spray lance and accessories before mounting. Clean the connectors of dust and sand. Make sure that no sand or dirt is blocking the movement of the pawl on the Click & Clean spray lance. Rinse the detergent spraying attachment after use. Clean the nozzles. Any repair should always be made in an authorized work- shop with original spare parts. 7 Maintenance 7.1 Cleaning of water inlet filter Clean the water inlet filter regu- larly once a month or more fre- quently according to use. Care- fully loosen the filter with a pair of pliers and clean it. Check that it is intact before re-mounting it. The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the guarantee. 7.2 Cleaning of nozzle A clogging up in the nozzle causes a pump pressure which is too high. This is why cleaning is required immediately. 1. Stop the machine and dis- connect the nozzle. 2. Clean the nozzle. IMPOR- TANT: The cleaning tool (11) should only be used when the nozzle is detached! 3. Flush the nozzle backwards with water. 7.3 Cleaning of machine vents The machine should be kept clean so as to let cooling air 7.4 Greasing of couplings To ensure an easy connec- tion and that o-rings do not pass freely through the ma- chine vents. dry up, the couplings should be greased regularly.
Page: 13
14 8 Trouble-shooting To avoid unnecessary disappointments, you should check the following before contacting the Nilfisk service organization: Symptom Cause Recommended action Machine refuses to start Machine not plugged in Plug in machine. Defective socket Try another socket. Fuse has blown Replace fuse. Switch off other machines. Defective extension cable Try without the extension cable. Fluctuating pressure Pump sucking air Check that hoses and connections are air- tight. Valves dirty, worn out Clean and replace or refer to local Nilfisk or stuck distributor Pump seals worn out Clean and replace or refer to local Nilfisk distributor. Motor busses Low voltage or Activate the trigger of the spray gun. low temperature Machine stops Fuse has blown Replace fuse. Switch off other machines. Incorrect mains voltage Check that the mains voltage corresponds to specification on the model tag. Thermal sensor activated Leave the washer for 5 minutes to cool down. Nozzle partially blocked Clean the nozzle (see section 7.2) Fuse blows Fuse too small Change to an installation higher than the amp. consumption of the machine. You may try without the extension cable. Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until regular working pressure resumes. Inadequate supply of Check that the water supply corresponds to mains water specifications required (see model tag) NB! Avoid using long, thin hoses (min. 1/2") Nozzle partially blocked Clean the nozzle (see section 7.2) Water filter blocked Clean the filter (see section 7.1) Hose kinked Straighten out hose. Machine often starts Pump/spray gun is Contact your nearest Nilfisk Service and stops by itself leaking Centre. Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw. no water comes out frozen No water supply Connect inlet water. Water filter blocked Clean the filter (see section 7.1) Nozzle blocked Clean the nozzle (see section 7.2) In case problems other than the above occur, please contact your local Nilfisk distributor. UK: Customer Services at Penrith - 01768 868995
Page: 14
15 9 Further information 9.1 Recycling the washer Make the old cleaner unusable immediately. 1. Unplug the cleaner and cut the electric cable. Do not discard electrical appli- ances with household waste. As specified in European Direc- tive 2002/96/EC on old electri- cal and electronic appliances, used electrical goods must be collected separately and recycled ecologically. Contact your local authorities or your nearest dealer for further information. 9.2 Warranty conditions Nilfisk guarantees high pres- sure washers for domestic use for 2 years. If your high pres- sure washer or accessories are handed in for repair, a copy of the receipt must be enclosed. Guarantee repairs are being made on the following condi- tions: z that defects are attributable to flaws or defects in materi- als or workmanship. (wear and tear as well as misuse are not covered by the guar- antee). z that the directions of this instruction manual have been thoroughly observed. z that repair has not been car- ried out or attempted by oth- er than Nilfisk-trained service staff. z that only original accessories have been applied. z that the product has not been exposed to abuse such as knocks, bumps or frost. z that only water without any impurities has been used. z that the high pressure wash- er has not been used for rental nor used commercially in any other way. Repairs under this guarantee include replacement of defec- tive parts, exclusive of packing and postage/carriage. Besides, we refer to your national law of sale. The machine should be for- warded to one of the service centres of the Nilfisk organisa- tion with description/specifica- tion of the fault. Repairs not covered by the guarantee conditions will be invoiced. (I.e. malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruction manual).
Page: 15
16 9.3 Accessories Only use original accessories. Click & Clean Car nozzle Special nozzle for enameled surfaces. Optimal distance: 30 - 50 cm. Click & Clean Undershassis nozzle 90° angled special nozzle for undercarriage and wheel arches. Integrated guide shoes. Click & Clean Multiangle adaptor Adjusted in angles from 0° - 90° for better working posture and cleaning of hard to get at places as for instance barrels or the underside of the lawn mower. Fits all nozzles. Click & Clean Brushes For cars and other surfaces. Available in more shapes. Extension hose 7 m extension hose increasing the working range. Underchassis spray lance Special spray lance for washing your car underneath. Drain & Tube cleaner 15 m long tube cleaner for the cleaning of tubes and drains. Water-sand- blasting equip- ment For removal of paint and rust. Sand available from do-it-your- self shops. Patio Plus Equipment for quick cleaning of patio/drive/flagstones. Garden brush Rotating brush for cleaning of wooden surfaces. Rim brush Rotating brush for cleaning of wheel rims. Wall hook For suspension of your high pressure washer on the wall. Rotary brush For cleaning vehicles and other surfaces. Water suction kit For removal of large amounts of water from e.g. garden pounds.
Page: 16
17 EU Declaration of Conformity Product: High Pressure Washer Type: Nilfisk E 130.2, E 140.2, E 145.2 Description: 230 V 1~, 50 Hz - IP X5 The design of the unit corresponds to the following pertinent regulations: EC Machine Directive 2006/42/EC EC Low-voltage Directive 2006/95/EC EC EMV Directive 2004/108/EC Applied harmonised standards: EN 60335-2-79 Applied national standards and technical specifications: IEC 60335-2-79 Anton Sørensen General Manager, Technical Operations EAPC Nilfisk Division of Nilfisk-Advance A/S Industrivej 1 DK-9560 Hadsund Hadsund, 01.10.2010 Detergents Stone & Wood Cleaner For flagstones, brick- and woodwork. Suitable for moss and algae. Plastic Cleaner For plastic and synthetic materials such as garden furniture. Metal Cleaner For cleaning of metal such as garden tools. Car Combi Cleaner For cars etc. With rinsing wax. Alu Cleaner For surfaces of aluminium. Applied with an atomizer. Oil & Grease Cleaner For cleaning of grease and oil on motors for instance. Applied with an atomizer. Wood Cleaner For cleaning of wooden surfaces incl. of wooden garden furniture. 10 EU Declaration of Conformity

Question & answers

Have a question about the Nilfisk E 130.2-9 PAD X-TRA but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Nilfisk E 130.2-9 PAD X-TRA. Please make sure that you describe your difficulty with the Nilfisk E 130.2-9 PAD X-TRA as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Ask a question about the Nilfisk E 130.2-9 PAD X-TRA


View a manual of the Nilfisk E 130.2-9 PAD X-TRA below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Nilfisk
  • Product: Pressure washers
  • Model/name: E 130.2-9 PAD X-TRA
  • Filetype: PDF
  • Available languages: Dutch, English, French