www.metabo.com Made in Germany
en Operating instructions 6
fr Mode d'emploi 10
es Instrucciones de manejo 15
BEV 1300-2 BE 850-2
P1 W 850 1100
P2 W 490 730
I120 V A 7.7 9.6
1 0-1100 0-1100
2 0-3100 0-3100
1 640 1100
2 1800 3100
1 1 9/16“ (40) 1 9/16“ (40)
ah,D/kh,D m/s2 4,2 / 1,5 4,2 / 1,5
LpA/KpA dB(A) 85 / 3 84 / 3
LWA/KWA dB(A) 96 / 3 95 / 3
The drill is suitable for non-impact drilling into metal,
wood, plastic and similar materials. It is also
suitable for thread tapping and screwdriving.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
Pass on your electrical tool only together with these
General Power Tool Safety Warnings
WARNING – Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference! The term "power tool" in the warnings
refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
2.1 Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2.2 Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
2.3 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
2.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
1. Specified Use
2. General Safety Instructions
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or in case of a power cut.
Ensure that the spot where you wish to work is
free of power cables, gas lines or water pipes
(e.g. using a metal detector).
Smaller workpieces must be secured such that they
are not carried along with the drill bit when drilling
(e.g. by clamping in a vice or on a work bench with
Keep hands away from the rotating tool! Remove
chips and similar material only when the machine is
not in operation.
Metabo S-automatic safety clutch. When the safety
clutch responds, switch off the machine
immediately! If the tool jams or catches, the power
supply to the motor is restricted. Due to the strong
force which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
The Metabo S-automatic safety clutch must not be
used for torque control.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break, or a high reverse torque may build up on the
Additional Warnings:California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
SYMBOLS ON THE TOOL:
...... Class II Construction
~.......... alternating current
n0......... no-load speed
rpm ...... revolutions per minute
.../min... revolutions per minute
See page 2.
1 Thumbwheel for gear selection
2 Additional handle / Additional handle with
vibration damping *
3 Geared chuck*
4 Futuro Plus keyless chuck *
5 Speed preselection setting wheel*
6 Thumbwheel for "impuls” function *
7 Electronic signal indicator*
8 Rotation selector switch
9 Locking button for continuous activation
10 Trigger switch
* depending on equipment
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
3. Special Safety Instructions
5. Initial Operation
Always install an RCD / GFCI with a maximum
trip current of 30 mA upstream.
To ensure that the drill chuck is securely fitted:
After initial drilling (clockwise), use a
screwdriver to firmly tighten the safety screw inside
the drill chuck (if applicable / model-specific).
Caution left-handed thread !
(see Section 8.7.)
5.1 Assembly of additional handle (2)
For safety reasons, always use the additional
Open the clamping ring by turning the additional
handle (2) counter-clockwise. Push the additional
handle onto the collar of the machine. Slide the
additional handle far enough forward so that it can
be turned. At the desired angle, pull it back and
6.1 Setting direction of rotation,
transport lock (switch-on lock)
Do not activate the rotation selector switch (8)
unless the motor has completely stopped.
See page 2.
R = Clockwise setting
L = Counter-clockwise setting
0 = Central position: transport lock setting
The drill chuck must be firmly screwed onto
the spindle and the safety screw inside the drill
chuck (if applicable / model-specific) must be firmly
tightened with a screwdriver. (Caution, left-handed
thread !) If rotated counterclockwise (e.g. when
screwing) it could otherwise become loose.
6.2 Selecting a gear
Select the desired gear by turning the
Change speed only when the machine
is in the process of running down
(briefly switch it on and off).
1st gear (low speed, high torque)
e.g. for screwdriving, drilling
2nd gear (high speed) e.g. for drilling
6.3 Preselect speed
Use the setting wheel (5) to preselect the maximum
speed. See page 4 for recommended drilling
6.4 Set “impuls” function
Put thumbwheel (6) on symbol .
= “impuls” function always switched on (for
easy insertion and removal of jammed
screws, even in case of damaged screw
heads. To enable clean drilling without centre
punching in tiles, aluminium or other
6.5 Switching on/off, changing speed
Switching on, speed: press the trigger (10).
The speed can be changed by pressing in the
The electronic soft start means that the machine
accelerates continuously until the preselected
speed is reached.
Release the trigger to switch off.
Continuous activation: While pressing on the
trigger (10), press in the locking button (9) and
then release the trigger. To switch off, press and
release the trigger (10) again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in
a safe position and concentrate.
6.6 Tool change with Plus (4) chuck
See illustrations A, page 2.
Opening the drill chuck:
Using one hand, hold the retaining ring securely
and, using the other hand, turn the sleeve in the
direction of the arrow -1.
The ratchet sound which can possibly be heard
after opening the drill chuck is functional and is
switched off by a reverse rotation of the sleeve.
If the chuck is very securely tightened: Unplug. Hold
the chuck using an open-end spanner at the flats on
its head, and turn the sleeve vigorously in the direc-
tion of the arrow -1.
Clamping the tool
- Insert the tool -2- as far as possible.
- Using one hand, hold the retainer ring securely.
- Turn sleeve in direction -3- until the noticeable
mechanical resistance has been overcome.
- Caution! The tool is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool safely clamped.
With a soft tool shank, retightening may be required
after a short period of operation.
6.7 Tool change with a geared chuck (3)
See illustrations B on page 2.
Opening the drill chuck: Open the geared chuck
with chuck key -1.
Clamping the tool: Insert tool -2- as far as possible
and, using the chuck key, evenly secure in all 3
6.8 Unscrewing chuck (when screwing with-
out chuck or when using attachments)
See illustrations C, D on the second last page.
Note for illus. C, D: Release by tapping lightly with a
rubber hammer, as shown, and unscrew.
Note: If a bit clamping bush (order no. 6.31281) is
attached, the screwdriver bit inserted in the
hexagon socket of the spindle is held in place.
Cleaning the keyless chuck:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close it
several times. The dust collected falls from the
opening. Regular use of cleaning spray on the jaws
and jaw openings is recommended.
Electronic signal display (7) (BEV 1300-2)
Rapid flashing - restart protection
When power is restored after a power failure, the
machine - which is still switched on - will not start by
itself for safety reasons. Switch machine on and off
Slow flashing - carbon brushes worn
The carbon brushes are almost completely worn.
If the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorised service centre.
Permanently lit - overload
If the machine is subject to continuous overloading
for longer periods, the power input to the machine is
limited. This prevents additional unauthorised
heating of the motor. Run the machine in idling until
it cools down and the electronic signal display
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
For a complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Explanatory notes on the information on page 3.
Changes due to technological progress reserved.
P1 =Rated input
P2 =Power output
I120 V =Current at 120 V
n1* =No-load speed
n2* =Load speed
ø max =Max. drill diameter
b =Chuck capacity
G =Drill spindle thread
H =Drill spindle with hexagon socket
D =Collar diameter
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
fluctuations in speed. The fluctuations disappear,
however, as soon as the interference fades away.
Using these values, you can estimate the emis-
sions from this power tool and compare these with
the values emitted by other power tools. The actual
values may be higher or lower, depending on the
particular application and the condition of the tool or
power tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protective
measures for the user - for example, any organisa-
tional steps that must be put in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
ah, D = Vibration emission value
(drilling into metal)
Kh,D = Uncertainty (vibration)
Typical A-effective perceived sound levels:
LpA = Sound pressure level
LWA = Acoustic power level
KpA, KWA = Uncertainty
Wear ear protectors!
7. Cleaning, Maintenance
11. Environmental Protection
12. Technical Specifications