LG LE6016N-NH manual

View a manual of the LG LE6016N-NH below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: LG
  • Product: Digital Video Recorder
  • Model/name: LE6016N-NH
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 0
OWNER’S MANUAL
Digital Video Recorder
MODEL
LE6016N
LE6016D
P/NO : COV30400902
Please read this manual carefully before operating
your set and retain it for future reference.
Page: 1
2 Safety Information
Safety
Information
1
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
FCC WARNING: This equipment may generate
or use radio frequency energy. Changes or
modifications to this equipment may cause harmful
interference unless the modifications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
•	 A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this
product in the end user.
•	 Caution: Danger of explosion if battery is
incorrectly replaced. Replaced only with the
same or equivalent type recommended by
the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
•	 Holes in metal, through which insulated wires
pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance
with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio
interference in which case the user may be required
to take adequate measures.
1
Safety Information
Page: 2
3
Safety Information
Safety
Information
	1
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a
qualified service person and should conform to all
local codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
Caution:
This product employs a Laser System. To ensure
proper use of this product, please read this owner’s
manual carefully and retain it for future reference.
Should the unit require maintenance, contact an
authorized service center. Performing controls,
adjustments, or carrying out procedures other than
those specified herein may result in hazardous
radiation exposure. To prevent direct exposure to
laser beam, do not try to open the enclosure. Visible
laser radiation when open. DO NOT STARE INTO
BEAM.
To disconnect power from mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/
EC, 2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327
AE Almere. The Netherlands
(Tel : +31-(0)36-547-8888)
Disposal of your old appliance
1.	 When this crossed-out wheeled
bin symbol is attached to a
product it means the product
is covered by the European
Directive 2002/96/EC.
2.	 All electrical and electronic
products should be disposed of
separately from the municipal
waste stream via designated
collection facilities appointed
by the government or the local
authorities.
3.	 The correct disposal of
your old appliance will help
prevent potential negative
consequences for the
environment and human health.
4.	 For more detailed information
about disposal of your old
appliance, please contact
your city office, waste disposal
service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
Page: 3
4 Safety Information
Safety
Information
1
IMPORTANT SAFETY
INSTRUCTIONS
1.	 Read these instructions.
2.	 Keep these instructions.
3.	 Heed all warnings.
4.	 Follow all instructions.
5.	 Do not use this apparatus near water.
6.	 Clean only with dry cloth.
7.	 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8.	 Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9.	 Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10.	 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11.	 Only use attachments/accessories specified by
the manufacturer.
12.	 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.
13.	 Unplug this apparatus during lightning storms
or when unused for long periods of time.
14.	 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
Page: 4
5
Safety Information
Safety
Information
	1
Please follow the
directions safely use
the product
The purpose of the following safety precaution
is to prevent any unexpected risk or damage
by using the product accurately as intended.
Warning
•	 Turn off the power of the product before
installing the product. Do not plug many
plugs into one outlet.
-
- It can cause an electric shock or a fire.
•	 Do not put any containers with liquid such
as water, coffee, beverage etc. on top of
the product.
-
- It can cause a fire, an electric shock or a
product problem.
•	 Do not put any heavy object on top of the
cable or excessively bend the cable.
-
- It can cause a fire.
•	 When wiping the surface of the product,
do not use water, chemical or detergent,
and always use a dry towel.
-
- It can cause an electric shock,
problems or scratches to the surface of
the product.
•	 Do not install the product where the level
of humidity, dust or smoke is high.
-
- It can cause an electric shock or a fire
•	 When unplugging the power, hold the
plug and unplug slowly. Do not hold the
plug with wet hands or plug to a loose
power outlet.
-
- It can cause an electric shock or a fire.
•	 Do not disassemble or reconfigure the
product. Because high level of current
flows on the device, it is dangerous to do
so.
-
- It can cause a fire, an electric shock or
an injury.
•	 Always check for dangerous elements
where the product is installed. If dangerous
elements (Moisture, damaged cable,
unstable installation etc.) are identified,
please contact your nearest service center.
-
- It can cause an electric shock or a fire.
•	 Because the cable connected to this device
can be damaged, keep at least 15cm of
clearance between where the product is
installed and where the power outlet is.
-
- It can cause a fire, an electric shock or
an injury.
•	 Install the product in a cool location not
exposed to direct sunlight. Do not install
the product where traffic is high or near
the heating devices.
-
- It can cause a fire.
•	 Install the product on a location with a flat
surface where it is ventilated well and not
too high.
-
- It can cause a problem or an injury.
•	 The power outlet must be grounded and
the voltage range must bet within 10% of
the rated voltage. Do not share the power
outlet with hair dryer, iron, refrigerator or
heating device etc.
-
- It can cause an explosion.
•	 When replacing the battery, always replace
with the same type of battery as the one
provided. When disposing the battery,
follow the direction of the manufacturer.
-
- It can cause an explosion.
Page: 5
6 Safety Information
Safety
Information
1
•	 For old hard drives, you may not be able to
recover the data stored on the drive. When
you use a damaged hard drive, you will
see a sign on the screen saying“Error or
defective”. For the old hard drive, contact
your nearest service center or the original
retailer to replace the hard drive.
-
- LG Electronics is not responsible for the
data loss from misuse by the user.
Any changes or modifications in
construction of this device which are not
expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
Caution
Please read the following precautions carefully
before installing the product and follow the
directions for installation.
•	 Do not install the product where the
level of humidity, dust or smoke is high.
•	 Do no install the product where it is
exposed to direct sunlight or close to the
heating device.
•	 Do not install the product where there is
danger of electric shock or near magnetic
object.
•	 Do not put objects with high conductivity
on top of the ventilation outlet of the
product.
•	 Make sure the power is turned off before
installing the product.
•	 Secure sufficient space to connect the
product when installing the product.
•	 Do not install the product where it is
not flat, not ventilated well or where
vibration is severe.
•	 When you install the product near
electronic appliances such as radio or TV,
it can cause problems to the product.
•	 Do not disassemble the product unless
done by a technician certified by LG
Electronics.
•	 Do not put heavy objects on top of the
product.
•	 Be careful not to let alien particles get
inside the product.
-
- It can cause a problem to the product.
•	 Install the product where it is ventilated
well.
-
- The product at least 15 cm away from
the wall power outlet because the
cable can be damaged.
•	 Do not install the product at a location
close to a product or broadcast receiver
with strong electric or magnetic wave.
•	 Do not put heavy objects on top of the
product.
-
- It can cause a problem to the product.
•	 Install the product at a flat and stable
location.
-
- The product may not operate normally.
•	 The product at a location with appropriate
level of temperature and humidity.
-
- Do not install the product where the
temperature is too high (40 °C or
above) or too low (0° or less).
•	 Because the vibration and impact can
damage the product, do not throw any
objects to the location where the product
is installed.
•	 Do not install the product where it is
exposed to direct sunlight or close to the
heating device.
Page: 6
7
Safety Information
Safety
Information
	1
•	 Firmly fixate the product at a location
where it is well ventilated.
-
- It can cause problems to the product
depending on the surrounding
environment. It is recommended to
use the Automatic Voltage Regulator. It
is recommended to wrap wires around
the Ferrite core.
•	 The power outlet must be grounded.
•	 If you hear any noise or smell any odor
from the product, turn the product off and
contact your nearest service center.
-
- It can cause a fire or an electric shock.
•	 Periodically have the product checked by
the service center to safety use the product
-
- When replacing the battery, always
replace with the same type of battery
as the one provided. When disposing
the battery, follow the direction of the
manufacturer.
-
- LG Electronics is not responsible for the
problem from misuse by the user
•	 Do not move or flip the product over while
using the product.
Page: 7
8
Contents
1
Safety Information
4	 IMPORTANT SAFETY
INSTRUCTIONS
5	 Please follow the directions
safely use the product
2
Before use
10	 2-1. Product characteristics
11	 2-2. Components
11	 2-3. Front side
11	 LE6016D model
12	 LE6016N model
13	 2-4. Rear side
14	 2-5. Remote Controller
14	 How to set the id of remote
controller
15	 2-6. Connection and initial
setting
16	 RS-485 connection
16	 Control port (Output)
connection
17	 Sensor (Input) connection
17	 About internal hard disk
18	 Hard disk installation
or replacement
3
Functional description
21	 3-1. Operation
21	 Start Up
22	 Shutdown
23	 3-2. Monitor Screen
27	 3-3. System Setting
27	 System
32	 Camera
37	 Event
41	 Network
45	 Information
47	 3-4. PTZ Control
49	 3-5. Search (Playback) &
Backup
Page: 8
9
	1
	2
	3
	4
	5
	6
49	 Time search
50	 Event Search
52	 Backup
4
Web viewer
55	 4-1. Installation
55	 Web viewer
installation
57	 4-2. Functional description
57	 Web viewer monitoring
window
58	 Web viewer search window
59	 Search dialog box
60	 Saving as AVI file dialog
box
5
Apple iPhone/iPod
61	 5-1. Functional description
61	 Real-time monitoring
6
Reference
63	 6-1. Check before requesting for
service
67	 6-2. Recommended device to
use
67	 List of recommended USB
memory
68	 Recommended list of CD/
DVD media
69	 List of supported PTZ
camera
70	 6-3. Initial setting list for factory
default
76	 6-4. Product specification
Page: 9
10 Before use
Before
use
2
2
Before use
2-1. Product characteristics
•	 Adopted the stable Embedded Linux
•	 Stable file system recovery even after power supply is disconnected from a power outage.
•	 Realized small file size and high video quality by applying the H.264.
•	 Supports terra byte hard disk (up to 1TB )
•	 Supports E-SATA port to use additional external hard disk.
•	 Real time recording
-
- Maximum of 480 IPS@352 X 240 at NTSC
-
- Maximum of 400 IPS@352 X 288 at PAL
•	 Supports various recording resolutions and qualities.
-
- D1(720x480), Half D1(720x240), CIF(352x240) at NTSC
-
- D1(720x576), Half D1(720x288), CIF(352x288) at PAL
-
- 5 stage recording qualities (Very high, high, normal, low, very low).
•	 Easy operation through various user interface and user friendly GUI system.
•	 Realized powerful multi-function.
-
- Real time video display or recording, network transmission and back up can be performed
simultaneously
•	 Easy search functions.
-
- Date/Time search (Calendar search), event search
•	 Recording before event. (Can be 2~4 seconds).
•	 Recording after event. (Can be only up 10 seconds).
•	 The operating condition pre-check function according to the change in motion detection and
movement detection
•	 Can set recording quality and number of recording frames per seconds.
•	 Powerful recording schedule management.
•	 Complete synchronization of video/audio.
•	 Easy software upgrading through USB storage device or network.
•	 Maximum of 5 clients can be connected to 1 DVR at the same time.
Page: 10
11
Before use
Before
use
	2
•	 Band width setting is automatically set depending on the network speed connected to this
device.
•	 Remote alarm notification via e-Mail.
•	 PTZ (Pen/Tilt/Zoom) operation.
•	 Remote control operation
•	 Key board control operation (optional)
•	 Supporting Daylight saving
•	 Simultaneous output to VGA and BNC
2-2. Components
Installation CD Owner’s Manual Power cable
Mouse Remote control Adapter
SATA cable
HDD power
cable
Screws
Reference: The type of components can be applied differently by the option.
2-3. Front side
LE6016D model
a	 b	 c	 d
e	 f	 g
Page: 11
12 Before use
Before
use
2
LE6016N model
There is no built-in DVD recorder at LE6016N model.
	 b	 c	 d
	 f	 g
a DVD Recorder: This is used for DVD backup.
b LED
•	 Hard disk LED: This is turned on HDD is accessed.
•	 Power LED: This is turned on when the power is turned on.
•	 Network LED: This is turned on when network is connected.
•	 Alarm LED: This is turned on when alarm event occurs.
c Navigation buttons
•	 At power off status, it is turned on by pressing“OK”button in some seconds.
•	 At power on status, instant panic recording is executed by pressing“OK”button in
some seconds.
•	 “SEARCH/LIVE”button is used as navigation key, when menu is shown, on the
Chapter 1 Before use other hand, it is used for switching key between SEARCH and
LIVE screen when menu not be shown.
d MENU/ESC: This is used to open or close menu.
e OPEN: This is used to open or close the door of DVD recorder.
f MOUSE: This is used to connect mouse.
g USB: This is used to connect USB external device.
CAUTION
Mouse should be connected to front side mouse port.
It will not work if you connect to USB port.
Page: 12
13
Before use
Before
use
	2
2-4. Rear side
e	f	 g	 h	i	
j	 k
a	 b	 c	 d
a Main output port: It is used to connect BNC type monitor. (It outputs the same video as
MAIN output.)
b Camera video input: These are used to connect cameras
c External HDD port: It is used to connect E-SATA HDD.
d Sensor/Alarm/RS-485 ports - These are used to connect sensor, alarm and RS-485 serial
communication port
e USB port: It is used to connect the USB external device.
f Ethernet port - It is used to connect RJ-45 Ethernet connector. (LAN PORT).
g VGA port: It is used to connect VGA monitor.
h Audio input port - It is used to connect audio output port of external device.
i Audio output port - It is used to connect audio input port of external device.
j SPOT output port - It is used to connect BNC type monitor.
k Power connector - It is used to connect Power adapter.
Page: 13
14 Before use
Before
use
2
2-5. Remote Controller
a
d
f
h
l
n
b
c
e
g
i
j
k
m
o
No. Function Description
a Power This is used to turn on/off the power.
b
Emergency
recording
This is used to start/stop emergency
recording.
c Number keys This is used to input channel or values.
d Plus(+) This is used to increase setting values.
e Minus(-) This is used to decrease setting values.
f CANCEL This is used to cancel a job.
g LIVE This is used to display real time screen.
h MENU This is used to display menu.
i SEARCH This is used to display screen search.
j vVbB, OK This is used to navigate each menu item.
k Play buttons
These are used to control playback
(Backward or forward search, play and
pause)
ø and buttons have no
function.
l PTZ Menu This is used to open PTZ Menu.
m
Export
backup
This is used to run backup.
ø It can be run in search mode.
n Split screen This is used for split screen display.
o
Auto
switching
This is used to display channel one by
one.
ø It works as event search at search
mode.
Reference: The shape of remote controller can be different by the model.
How to set the id of remote controller
1. 	 Press cancel button about 3 seconds then light of power button turns on.
2. 	 Enter two digit numbers which is the id of remote controller using number keys.
ø	 You have to input‘0’first when you are to input one digit number.
Ex) In case you want to use‘2’as ID, input‘02.
3. 	 Every time you press the number key the light of power button will blink.
4. 	 Stopping blinking means that the id is saved.
Page: 14
15
Before use
Before
use
	2
2-6. Connection and initial setting
Caution
•	 The camera or other external devices can be connected to this device in numerous
methods. Refer to the user manual of the camera or other external device for addition
information on connection methods.
•	 When installing the camera, check whether the power of the camera is turned off.
•	 After installing the monitor, turn on the power of the DVR.
Connect the BNC type
monitor. (The same
video output as VGA.)
Connect VGA monitor.
Connect the audio. (Line input)
Connect the camera for coaxial
connection.
Connect the
network cable.
Connect the BNC
type monitor.
(SPOT output)
Connect the speaker or amplifier.
Connect
E-SATA HDD.
Connect USB
device.
Connect the
power adapter.
Page: 15
16 Before use
Before
use
2
RS-485 connection
①	 This device has 1 data port (RS-485).
②	 Use this port to connect the PTZ camera or the
keypad. (Optional)
③	 PTZ camera / keyboard connection
i. 	 Connect the PTZ serial communication cable to
the RS-485 port.
ii. 	 When connecting the cable, make sure that
the TX- of the device is connected to the RX-
(TX-) of the camera(keyboard), and TX+ of the
device is connected to the RX+(TX+) of the PTZ
camera(keyboard).
iii. 	 Recommended initial data setting is 9 600 baud
rate, 8 data bits, 1 stop bit and no parity.
iv. 	 When connecting the PTZ camera or keyboard, always change the setting of the DVR
setting menu according the RS-485 setting of the camera, keyboard and this device.
v. 	 Set the same baud rate when you are to use PTZ camera and keyboard at the same time
Control port (Output) connection
①	
For interface and auto control with the external sensor, the interfacing control output port
(Set value from“Setup Ò Event Ò Sensor/Motion/Video loss”menu) and the“RELAY”port are
connected.
②	 If the control device (Alarm light, amplified siren, external relay etc.) is“NC (Normal Close)”type,
connect to the control output NC (Normal Close) port.
③	 If the control device (Alarm light, amplified siren, external relay etc.) is“NO (Normal Open)”type,
connect to the control output NO (Normal Open) port.
Page: 16
17
Before use
Before
use
	2
Sensor (Input) connection
Connect one of the signal cables (2 cables) of various
sensors (IR sensor, heat ray detector, magnetic etc.) to the
COM port and connect the remaining signal cable to the
sensor number you want. (Sensor“NC, NO”type can be set
from“Setup Ò Event Ò Sensor”menu.)
1 Sensor input 1
2 Sensor input 2
3 Sensor input 3
4 Sensor input 4
G Ground
5 Sensor input 5
6 Sensor input 6
7 Sensor input 7
8 Sensor input 8
G Ground
NOTE
NC and NO cannot be selected simultaneously.
About internal hard disk
The hard disk installed inside the device is a precision device which can be damaged even with the
small impact. To prevent the hard disk from being damaged, manage the device as follows.
To prevent the data loss, it is recommended to back up any important data into an external storage
device. When installing or uninstalling the hard disk, you must always turn off the power of the
product.
•	 If the power is turned on, do not move the device.
•	 Do not install this device where it is too hot and humid and where the temperature change is
sudden. It can cause a problem to the device.
•	 DO NOT pull out the plug or intercept the power supply while this device’s power is on.
•	 When there is a power outage while the power is turned on, some data can be lost.
•	 Do not drop the hard drive or put any metallic object, such as coins, inside the device.
•	 In case of a power outage while recording, avoid adding, replacing or moving the HDD. The
recorded data can be lost. In this case, turn on the power with the original hard disk that was
used while the power outage occurred. And then add, replace or move the HDD.
•	 Because the hard disk is a high precision device, the parts inside the disk can be damaged at
the slightest impact. Please read the following precautions in detail and follow the directions.
-
- Do not directly put the hard disk on the desk or table. Because the parts inside the hard
disk can be damaged at the slightest impact, put a thick cushion below the hard disk.
-
- If you use the motored driver, the parts inside the hard disk can be damaged from the
vibration.
-
- When replacing the hard disk, be careful not to cause any impact to the other parts.
Page: 17
18 Before use
Before
use
2
-
- Be careful not to cause an impact from the tools and hard disk used for the installation.
•	 Protect the hard disk from static electricity.
CAUTION
This device has elements to cause an electric shock, an accident or a problem to the product.
Also the hard disk may not be recognized or operated properly due to incorrect installation and
setting. Therefore consult with an experienced expert technician when installing the hard disk.
Hard disk installation or replacement
Hard disk installation
After turning on the power of the device, unplug the power from the outlet.
1.	 Loosen the screw on the left, right and rear side of the
product.
2.	 Separate the cover of the main unit.
3.	 Remove the screws on the bracket holding the hard disk,
separate the bracket from the hard disk.
4.	 Install the hard disk to the bracket and tighten the 4 screws.
B 	 Connecting bracket to hard disk
Set the SATA cable connection port
to lower direction to install the hard
disk to the bracket.
Connect the bracket to hard disk by
tighten the 4 screws.
5.	 After installing the bracket on the main unit, tighten the screws.
Page: 18
19
Before use
Before
use
	2
6.	 Connect the power cable of the hard disk.
7.	 Connect the SATA cable to the hard disk.
<Connecting power cable> <Connecting SATA cable>
8.	 Connect the SATA cable to the SATA port of the main board.
9.	 Close the cover of the main unit.
10.	 Tighten the screws.
11.	 After installing the hard disk, you must format the hard disk from the setting menu.
<LE6016N> <LE6016D>
-
- The first SATA cable port on the main board must be connected at all times. If a hard disk is
not connected, this device may not operate normally.
Hard disk replacement
First turn of the power of the device and then unplug the power.
1.	 Loosen the screw on the left, right and rear side of the product.
2.	 Separate the cover of the main unit.
3.	 After removing all of power/SATA cable connected to hard disk, please separate hard disk
bracket from the body.
Page: 19
20 Before use
Before
use
2
4.	 Loosen the screws on the left and right side of the bracket holding the hard disk.
5.	 Separate the hard disk from the bracket holding the hard disk.
6.	 In the reverse order of removing the hard disk, assemble the new hard disk.
7.	 After replacing the hard disk, turn on the power of the device.
8.	 Reference
-
- Each SATA cable must be connected to the connecting port precisely.
-
- Do not vertically put the hard disk in upright position or put other objects on top of the
hard disk.
-
- When connecting/disconnecting the hard disk, do not use a motored tool.
-
- Refer to the following when adding/replacing the hard disk.
Connecting E-SATA HDD
•	 Turn off the power of DVR then connect E-SATA HDD to E-SATA port. And turn on the power of
E-SATA HDD first then turn on the power of DVR.
•	 E-SATA HDD is used only for recording, it cannot be used for any other purpose like backup, for
example.
Recommended list of hard disk
Hard disks of below are the ones proved to be compatible through experiment.
Please refer to when adding or replacing the hard disk.
Capacity LE6016N LE6016D
250 GB
WD2500AAJS
Western Digital
ST3250310CS
Seagate
WD2500AAKS ST3250312CS
500 GB WD5000AAKS ST3500312CS
1 TB WD10EALS ST3100322CS
CAUTION
When you select the hard drive in use for resetting, the video data saved previously will be
deleted. Therefore you must be careful.
Page: 20
21
Functional description
Functional
description
	3
3-1. Operation
Start Up
1.	 Turn on this device, then it boots with power indicator light turned on.
2.	 After booting it will be displayed as the LOGOUT id.
3. 	 Pressing button, then the login window would be displayed. Select user and press“OK”
button to continue.
x
x [USER]
You may select user to login and authority is restricted by kind of user. The access rights
can be set for each user.
1)	 admin for system administrator (Access rights to Live, Search and Setup)
2)	 user1/user2/user3 for general user (Access rights can be set by administrator)
3
Functional description
Page: 21
22 Functional description
Functional
description
3
x
x [password]
The default user and password are set to
‘admin’and‘000000’as shown above. Click
password input area, you will see the screen
keypad as right.
4.	 Input password by using virtual keypad on screen.
5.	 Click“OK”button to execute DVR system and you will see live screen.
Shutdown
1.	 While the status is logged in, Press button, then logout window will be displayed as below.
x
x Selection: Select the Log Out or EXIT.
x
x 	
USER : Display current user has logged.(admin/user1/user2/user3)
x
x 	
PASSWORD : Input password.
2.	 Click“OK”button to“Log Out”or“DVR Shutdown”.
Page: 22
23
Functional description
Functional
description
	3
3-2. Monitor Screen
A B
D
C
E
A	[Camera name]
•	 Shows camera name
•	 If you want to modify camera name, you can do so by selecting [Setup] Ò [Camera]Ò
[Channel]
B	[Status icon] (OSD)
•	 Status icon shows current status of camera/recording.
•	 (OSD Feature)
Item Icon Description
Camera
Audio Icon
Motion Icon
PTZ Icon
Page: 23
24 Functional description
Functional
description
3
Recording
Continuous Recording
Immediate Recording
Recording by Motion
Non Recording
Recording by Sensor
C	[Channel selection]
•	 Selected channel shows green rectangle on the edge of the screen.
D	[Live view]
•	 It shows current live view as real time.
E	[System control toolbar]
a	 b	 c	 d	 e	 f	 g	 h	i	
j	
k	
l	
m	
n	
o
p	
q	 r	 s
a	[Network status display]
•	 It shows current connection status of network.
(Black : It shows disconnected status.)
(Blue : It shows connected status.)
•	 If you want to modify network settings, you can do so by selecting [Setup] Ò
[Network] Ò [TCP/IP]
b	[Current Date/Time]
•	 Current date and time is displayed.
•	 If you want to modify date and time, you can do so by selecting [Setup] Ò
[System] Ò [Date]
c	[Setup]
•	 Set the system environment and function.
•	 Refer to Chapter“3-3. System Setting”.
Page: 24
25
Functional description
Functional
description
	3
d	[Live screen]
•	 This is the button to switch over to the live display window to view the realtime
video screen.
e	[Search]
•	 This is the button to switch over to the search window to view the recorded screen.
•	 Refer to Chapter“3-5. Search (Playback) & Backup”
f	[PTZ control]
•	 This is the button to control the PTZ camera
•	 Refer to Chapter“3-4. PTZ Control”.
g	[Divided screen selection]
•	 1/4/9/13/16 divided screen can be displayed in live view.
h	[Auto sequential]
•	 Click button and each channel will be switched automatically.
•	 This function does not work at 16 divided screen.
•	 You can set the switching interval at [Setup] Ò [System] Ò [Overview] Ò
[Auto- switching].
i	[Logout]
•	 Use Lock menu to change user or lock system operation.
j	[Relay out off(Alarm off)]
•	 When alarm (relay out) is on by event, you can stop the alarm with it.
•	 Press button to stop alarm (relay out).
•	 If next event occurs after alarm (relay out), the alarm will start again.
k	[Stop]
•	 Click this button to stop playback recorded data.
l	[Fast backward playback]
•	 Click this button to playback fast backward. The speed of fast backward playback
can be set to one of the following, X2, X4, X8, and X16.
m	[Forward playback]
•	 Click this button to playback forward as normal speed.
•	 Live screen can be switched to playback instantly by clicking this button.
n	[Fast forward playback]
•	 Click this button to playback fast forward. The speed of fast forward playback can
be set to one of the following, X2, X4, X8, and X16.
Page: 25
26 Functional description
Functional
description
3
o	[Backup]
•	 Click this button to run backup recorded data.
•	 Refer to Chapter“3-5 Search (Playback) & Backup”.
p	[System Log]
•	 This shows the system log in DVR.
•	 Click button to show the system log list.
•	 You can see the log of previous date or next date by using b / B button.
•	 You can see the previous or next log list by using ( - ) / ( + ) button.
•	 Click“OK”button to close window.
•	 Clicking button at search mode, Event search dialog box will be shown. Refer
to“Event search”.
q	[Information]
•	 It shows the system information.
r	[Playback status]
•	 It shows the playback status.
s	[Bookmark]
•	 You can add playback position (date/time) to access immediately later.
NOTE
You can show or hide system control bar by double clicking right mouse button.
Page: 26
27
Functional description
Functional
description
	3
3-3. System Setting
System setting can be configured by setup menu. Working condition can be specified by front
button / mouse / remote controller.
Only admin user can setup system configuration by menu.
System
A
B
D
C
E
A	[Overview]
•	 You can specify the system configuration by this menu.
•	 Use b / B button to change configuration.
Page: 27
28 Functional description
Functional
description
3
x
x REMOTE ID: ID can be selected from 00 to 99.
x
x DE-INTERLACE: Enable or disable de-interlace feature for playback screen. De-interlace
feature is only available for‘D1’resolution.
x
x AUTO SWITCHING : Set dwell time when auto switching function is working. (1 Sec ~
30 Sec)
x
x SPOT-DIVISION: Set the division mode for SPOU OUT screen.
x
x SPOT-OUT : Select spot channel. (channel 1~16, AUTO). If you select“AUTO”, Spot will be
changed sequentially.
ø	 When spot channel is changed automatically, dwell time that specified by Spot
from AUTO SWITCHING is applied.
x
x BUTTON BUZZER : Select button buzzer on / off.
x
x LANGUAGE : Select language.
x
x OVERWRITE: If you select“ON”, when recording space of HDD is exhausted, it overwrites
on the oldest recorded data to continue recording.
x
x USE DATA RETAIN : data saving period can be set from 1 day to 60 days.
B	[Date/Time]
•	 Specify date and time of system.
•	 You can specify setting by using b / B button
•	 Select date and time, then you will see virtual keypad as below.
x
x DATE : Specify current date
x
x TIME : Specify current time
Page: 28
29
Functional description
Functional
description
	3
x
x LOCALE : Specify locale of country.
If you click button, the time zone dialog box will be shown as below, and
select a time zone, then click OK to change setting.
x
x NTP SERVER : It is used to set internet time server.
ø	 Daylight saving time is applied automatically according to corresponding
location.
C	[Password]
•	 You can specify password and authority of each user.
•	 The password can be set max 20 digits.
•	 You can set authority for each camera, setup, search/backup, and PTZ control for each user.
ø	 If you access as Admin account, previous password is not required.
ø	 No authority setting is available for Admin account.
Page: 29
30 Functional description
Functional
description
3
ø	 Only camera authority is allowed for Logout account.
ø	 Logout screen setting is applied as the same for Spot-Out.
ø	 White screen will be shown for the cameras which are not set the authority.
D	[Initialize]
•	 You can initialize data and configuration by this menu.
x
x FACTORY : Delete entire data in the system and restore as factory default.
•	 The dialog box will be shown as below at the first booting after factory default
setting.
•	 The text in the dialog box will be shown in English as default.
ø	 You can set time zone by clicking SET button, and which is the same as [SYSTEM]
Ò [DATE/TIME] menu.
x
x LOG : Delete all event log.
x
x SETTING : Delete setting of configuration.
x
x HDD : Format HDD data.
Page: 30
31
Functional description
Functional
description
	3
NOTE
•	 If data is initialized, it can’t be recovered. Before use“initialize”, important data must be
backup.
•	 HDD Factory initialization makes format HDD and you will loose recorded data
E	[Controller]
•	 Connect keyboard controller to DVR system.
•	 Setup configuration to access DVR with keyboard controller.
(*Refer to controller user manual)
ø	 Supported device : LKD1000 Dynamic Controller (LG)
Page: 31
32 Functional description
Functional
description
3
Camera
On the camera menu, channel, recording, schedule, color and PTZ can be configured.
A
B
D
C
E
A	[Channel]
•	 You can specify channel name and audio for each camera.
x
x CAMERA : Select camera to change
x
x CHANNEL NAME : Input channel name (Max 8 digits)
x
x AUDIO : Specify channel that audio is related.
Page: 32
33
Functional description
Functional
description
	3
B	[Recording]
•	 You can specify recording configuration.
x
x TOTAL FRAME : Max frame rate has restricted by screen resolution.
x
x CAMERA : Select camera to set frame and quality.
x
x RESOLUTION : Specify screen resolution. (CIF / HALF D1 / D1 )
x
x FRAME : You can specify recording frame rate when recording method is continuous
for selected camera.
ø	 Frame rate cannot exceed event frame rate.
x
x EVENT FRAME : You can specify recording frame rate when recording method is event
for selected camera.
x
x QUALITY : Specify image quality for selected camera.
(VERY HIGH, HIGH, NORMAL, LOW, VERY LOW)
x
x Click“APPLY ALL”button to apply setting to all cameras.
Page: 33
34 Functional description
Functional
description
3
C	[Schedule]
•	 You can specify recording method by schedule with date and time.
x
x Click time table to change recoding method.
x
x Click channel number to change recording method for all time.
x
x Click time label to change recording method for all channel.
x
x Click“APPLY ALL”button to change settings to all days. (From Sunday to Saturday)
C : 	 Continuous recording method
H : 	Continuous recording + event recording method (Motion, Sensor)
E : 	 Event recording method: if event (Motion, Sensor) happens, recording works.
N : 	No Recording.
x
x Click‘HOLIDAY’button to specify holidays.
Page: 34
35
Functional description
Functional
description
	3
-
- You can select month and day by clicking date button.
-
- Click the Add button, the selected month and day will be added to the list of
holidays.
-
- Click the Delete button to delete the selected date from list.
D	[Color]
•	 You can adjust brightness, contrast, saturation and hue.
E	[PTZ]
•	 This is to setup the PTZ configuration.
x
x CAMERA : select camera to setup PTZ.
x
x DEVICE NAME : Select camera name.(Max 15 cameras supported)
1.	 LG Multix_E / LG Co.,Ltd
2.	 LG Multix / LG Co.,Ltd
3.	 LPT - A100L / LG Co.,Ltd
4.	 LVC-C100 / C200HM / LG Electric Inc
5.	 HSDN251 / Honeywell Co.,Ltd
Page: 35
36 Functional description
Functional
description
3
6.	 MD200 / 2000 / 1200 / 800 / Sony Co.,Ltd
7.	 New Born / NEW BORN HIGHTECH
8.	 WVCS850 / Panasonic
9.	 PELCO-D / PELCO Co.,Ltd
10.	 PELCO-P / PELCO Co.,Ltd
11.	 SCC-641 / SCC-643 / SAMSUNG Co.,Ltd
12.	 SPD-2300 / 3000 / 3300 / SAMSUNG Co.,Ltd
13.	 SUNGJIN / SUNGJIN Co.,Ltd
14.	 TPD7720 / DYNACOLOR,INC
15.	 V1305R-DC / V1300RB / CRX - 1013 / VICON
x
x DEVICE ID : Select ID that configured in camera.
x
x BPS : Bit rate Per Second for data transmission.
Default value of BPS is 9600
ø	 Value can be selected by camera setting: (1200/ 2400/ 4800/ 9600/ 19200/ 38400/
57600/ 115200 bps)
x
x TOURING INTERVAL : This is time interval before moving to next preset position when
touring.
•	 Select one from 5 seconds, 10 seconds, 20 seconds, 30 seconds, 1 minute, 3
minutes and 5 minutes.
•	 The default is 1minute.
NOTE
Basically, DVR support one RS-485 port for PTZ connection.
Page: 36
37
Functional description
Functional
description
	3
Event
You can specify the processing when event occurs like sensor, motion detection, video loss, and
the email notification settings when event occurs.
A
B
D
C
A	[Sensor]
•	 You can specify the processing when event occurs from input device.
x
x SENSOR : Selecting sensor number. ( 1 ~ 8 )
x
x TYPE : Setting NO / NC type.
•	 (Normal Open) : The type of input device is opened normally.
•	 (Normal Close) : The type of output device is closed normally.
Page: 37
38 Functional description
Functional
description
3
x
x CHANNEL : Selecting associated channel with the sensor input. (OFF/1~16)
x
x ALARM : Setting alarm out when event occurs from input device.(OFF/1~4)
x
x ALERT : Setting sound a buzzer when event occurs from input device. (ON/OFF)
x
x SPOT-OUT : Setting spot out when event occurs from input device.(ON/OFF)
x
x DURATION : Setting the duration time from event occurs. ( 1~10 Sec., OFF)
B	[Motion detection]
•	 You can specify the process when motion is detected.
x
x CHANNEL : Selecting camera which is associated event.
x
x MOTION ZONE : Setting the motion detection zone.
-
- Click “SET” button to setting motion detection zone.
-
- The red-marked area is set as motion detection zone.
-
- Click right button of mouse on the screen to display menu window.
Page: 38
39
Functional description
Functional
description
	3
>
> SELECT ALL : Selecting entire area.
>
> UNSELECT ALL : Unselecting entire area.
>
> SAVE : Saving selected area as a motion detection zone.
>
> EXIT : Exiting motion zone setting.
x
x SENSITIVITY : Setting the motion sensitivity. (VERY HIGH, HIGH, NORMAL, LOW, VERY
LOW)
x
x ALARM : Setting alarm out when motion is detected.
x
x ALERT : Setting sound a buzzer when motion is detected.
x
x SPOT-OUT : Setting spot out when motion is detected.
x
x DURATION : Setting the duration time from motion detection occurs.
C	[Video loss]
•	 You can specify the processing when video loss.
x
x CHANNEL : Selecting camera which is associated event. (1~16)
x
x ALARM : Setting alarm out when video loss. (OFF/1~4)
Page: 39
40 Functional description
Functional
description
3
x
x ALERT : Setting sound a buzzer when video loss. (ON/OFF)
x
x DURATION : Setting duration time from video loss. (OFF/1~10 Sec.)
D	[E-mail]
•	 You can set the E-mail notification when event occurs.
x
x MODE : Enabling or disabling E-mail notification. (OFF / Authentication / Not
authentication)
x
x SMTP SERVER : Setting the IP address or domain name of SMTP server.
x
x PORT : Setting the TCP port number of SMTP (Default value is 25).
x
x ACCOUNT : Setting the E-mail account registered in SMPT server.
x
x PASSWORD : Setting the password of the E-mail account.
x
x SENDER : Setting the E-mail address of sender.
x
x RECEIVER : Setting the E-mail address of receiver.
x
x E-MAIL TEST : Click to send testing E-mail, then RECEIVER can check the testing E-mail.
	 <Success>
	 <Failure>
ø	 SMTP server does not support encrypted E-mail protocol.
Page: 40
41
Functional description
Functional
description
	3
Network
You can set the network environments.
A
B
D
C
E
A	[TCP/IP]
•	 You can specify the TCP/IP setting according to network environment.
•	 Specifying the TCP port number of Web, Playback and Live.
•	 Default values: Web(80), Playback(9091), Live(9092)
For dynamic IP or PPPoE
•	 All the items of IP address, subnet mask, gateway and DNS are disabled and set
each value automatically.
•	 You can specify account and password of PPPoE using PPPoE button which is
located left below.
Page: 41
42 Functional description
Functional
description
3
For static IP
x
x IP ADDRESS : Enter IP address received from ISP using screen keyboard.
x
x SUBNET MASK : Enter subnet mask received from ISP using screen keyboard.
x
x GATEWAY : Enter gateway received from ISP using screen keyboard.
x
x DNS : Enter the DNS IP address received from ISP using screen keyboard.
x
x MAC ADDRESS : This is hardware specific unique address of network device, so user
cannot set this value.
ø	 8000~65535 port number is recommended.
ø	 Do not use the same port number with each other.
web(80),playback(9091),live(9092),CMS LG(9100)
ø	 If the network of DVR is connected via router, you must set Configuration of port
forwarding according to the router.	
(web, search, live ports) Please refer to user’s guide of the router which you are
using.
B	[Streaming]
•	 You can set each item about the network video streaming.
x
x TOTAL FRAME: : Total frame rate set / Maximum available frame rate
x
x CAMERA: Selecting camera.
x
x FRAME: Frame rate per a second for each camera
x
x QUALITY: Selecting video encoding quality (VERY HIGH, HIGH, NORMAL, LOW, VERY
LOW)
x
x Click“ APPLY ALL ”button to apply setting to all cameras.
Page: 42
43
Functional description
Functional
description
	3
C	[DDNS]
•	 You can use DDNS service provided by LG.
•	 You can connect to DVR easily using host name instead of IP address with LG DDNS
x
x MODE : Enabling or disabling DDNS.
x
x SERVER : IP address of DDNS.
x
x PORT : TCP port number of DDNS.
x
x DOMAIN : The domain name of DVR device.
x
x INTERVAL : Setting the interval of IP address updating.
D	[CMS]
•	 Specifying IP address and TCP port number of CMS.
x
x MODE : Enabling or disabling event report to the central monitoring center when
event occurs.
x
x IP ADDRESS : The IP address of the central monitoring center.
Page: 43
44 Functional description
Functional
description
3
x
x PORT : The TCP port number of the central monitoring center.
ø	 8000~65535 port number is recommended.
ø	 Do not use the same port number with each other.
web(80), playback(9091), live(9092), CMS LG(9100)
E	[Event filter]
•	 Specifying the event which will be sent to the central monitoring center and E-mail.
x
x SYSTEM START : Enabling or disabling the system start event.
x
x SHUTDOWN : Enabling or disabling the system shutdown event.
x
x SETTING CHANGE : Enabling or disabling the setting change event.
x
x LOGIN / LOGOUT : Enabling or disabling the login / logout event.
x
x SENSOR DETECTION : Enabling or disabling the sensor detection event.
x
x MOTION DETECTION : Enabling or disabling the motion detection event.
x
x VIDEO LOSS : Enabling or disabling the video loss event.
x
x ALARM OUTPUT : Enabling or disabling the alarm output event.
Page: 44
45
Functional description
Functional
description
	3
Information
You can view the general system information and run software update.
A
B
D
C
A	[System information]
•	 You can view the system information.
x
x MODEL : Model name of the device.
x
x IP ADDRESS : The IP address assigned to the device.
x
x MAC ADDRESS : The MAC address assigned to the device.
x
x F/W VERSION : The version number of firmware.
x
x OS VERSION : The version number of Operating system.
x
x VIDEO TYPE : Showing NTSC or PAL. This is set automatically by detecting incoming
video signal, so user cannot chance this value.
Page: 45
46 Functional description
Functional
description
3
x
x HDD: HDD capacity, using ratio and status.
-
- * mark is shown at the HDD which is currently recording.
-
- “NOT HEALTHY”is shown according to the HDD status.
-
- The HDD connected to E-SATA port is displayed as“External HDD”.
B	[System log]
•	 You can view the system log. (Refer to page 25 [System log])
C	[F/W Update]
•	 You can run firmware update.
x
x FILE : You can specify the firmware file to update using b / B buttons.
D	[Setting update]
x
x IMPORT: You can replace current setting values with new values from USB memory.
(OFF/ON)
x
x EXPORT: You can export current setting values to USB memory. (OFF/ON)
Page: 46
47
Functional description
Functional
description
	3
NOTE
USB memory stick is needed to update F/W or settings.
It takes about 5 seconds to recognize USB memory device after connected.
“USB is not detected.”Message will be shown when you are to run backup without
connected USB.
3-4. PTZ Control
It is used to control PTZ camera which is connected at RS-485 port. Settings of camera and DVR
should be done if you are to control PTZ camera.
1.	 Click the icon to control PTZ.
2.	 Control the PTZ camera using each item below.
Page: 47
48 Functional description
Functional
description
3
①	 Click this button to close the PTZ control window.
②	 Click this spin control to select PTZ camera. (1~16)
③	 Click this spin control to specify the moving speed of PTZ camera (1~6).
④	 Click this button to show the OSD menu of camera.
⑤	 Click these direction buttons to pan or tilt camera.
⑥	 Click to control zoom in or out.
⑦	 Click to control the focus of camera manually.
⑧	 Click to control the iris of camera manually.
⑨	 Click to select preset number.
⑩	 Click to move to selected preset position.
⑪	 Click to set current position as a new preset position.
⑫	 Click to delete specified preset number.
⑬	 Click to start touring, which function traverse each preset position one by one according to
dwell time.
⑭	 Click to stop touring.
x
x Setting a new preset position
1.	 Move camera position using direction button ⑤.
2.	 Select the preset number to set using button ⑨.
3.	 Click button ⑪“SET”.
4.	 Repeat process 1 ~ 3 stage to set another preset position.
ø	 Preset numbers are available up to 10.
ø	 The maximum preset number is different according to the specification of camera.
x
x Moving camera to preset position
1.	 Select the preset number to move using button ⑨.
2.	 Click button ⑩“GO”.
ø	 Moving camera to preset position is only available when the camera supports
preset feature.
x
x Deleting preset position
1.	 Select the preset number to delete using preset number button ⑨.
2.	 Click button ⑫“CLEAR”.
ø	 Deleting preset position is only available when the camera supports.
x
x Starting touring
1.	 Click button ⑬“START”.
2.	 Then it will start traversing each preset position one by one automatically.
Page: 48
49
Functional description
Functional
description
	3
x
x Stopping touring
1.	 Click button ⑭“STOP”.
2.	 Then it will stop traversing.
NOTE
The tour which is working will be stop after the setting is changed.
3-5. Search (Playback) & Backup
Various features are available for user to search recorded data easily.
Time search
You can search recorded data with date and time.
x
x Search method
A.	 Click button on menu bar of real time screen.
B.	 Select the date you want to search on the calendar above and click“OK”.
(The date with recorded data is displayed in bold.)
C.	 Then recorded time table will be displayed. (Refer to the image below)
D.	 The recorded data will be displayed after you select time and click“OK”button.
Page: 49
50 Functional description
Functional
description
3
ø	 Click the“CANCEL”button to select date again.
ø	 You can select a data if data are duplicated at the same time stamp using spin
box below. The spin box is shown only when data are duplicated at the same time
stamp, which is caused when daylight saving period.
ø	 Bigger number of duplicated data stands for more recent data.
Event Search
You can search recorded data using event occurrence time.
A.	 Click mouse on the icon of the menu bar which is located in the lower position of the
search mode screen.
B.	 Use bB buttons on the upper right side to select camera to search.
C.	 Check sensor, motion check box below to filter out the events.
D.	 Move to previous or next page using – and + buttons.

Question & answers

i forget the admin password of dvr model LG LE6016N-NH .. plzz tell me that how can i reset this???

Published on 1 year ago by shahroz

Ask a question about the LG LE6016N-NH

Have a question about the LG LE6016N-NH but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the LG LE6016N-NH. Please make sure that you describe your difficulty with the LG LE6016N-NH as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.