View a manual of the LG BP120 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
OWNER’S MANUAL Blu-ray Disc™/DVD Player Please read this manual carefully before operating your set and retain it for future reference. BP120 P/NO : MFLxxxxxxxxxxx
Getting Started 3 Getting Started 1 Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION : CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service centre. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.
Getting Started 4 Getting Started 1 This device is equipped with a portable battery or accumulator. Safety way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Getting Started 5 Getting Started 1 Notes on Copyrights y y Because AACS (Advanced Access Content System) is approved as content protection system for Blu-ray Disc format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions are imposed on playback, analog signal output, etc., of AACS protected contents. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product. y y Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected contents. To obtain additional information on AACS, BD- ROM Mark, BD+, or this product, please contact an authorized Customer Service Centre. y y Many BD-ROM/DVD discs are encoded with copy protection. Because of this, you should only connect your player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs. y y This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi. Reverse engineering or disassembly is prohibited. y y Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use, display, distribution, or revision of television programs, videotapes, BD-ROM discs, DVDs, CDs and other materials may subject you to civil and/ or criminal liability. Important Notice for TV colour system The colour system of this player differs according to currently playing discs. For example, when the player plays the disc recorded in the NTSC colour system, the image is output as an NTSC signal. Only the multi system colour TV can receive all signals output from the player. y y If you have a PAL colour system TV, you will see just distorted images when using discs or video contents recorded in NTSC. y y The multi system colour TV changes the colour system automatically according to input signals. In case that the colour system is not changed automatically, turn it off and then on to see normal images on screen. y y Even if the disc recorded in NTSC colour system are well displayed on your TV, these may not be recorded correctly on your recorder.
Table of Contents 6 Table of Contents 1 Getting Started 3 Safety Information 8 Introduction 8 – Playable Discs and symbols used in this manual 9 – About the “7” Symbol Display 9 – Compatibility Notes 10 – File requirement 11 – AVCHD (Advanced Video Codec High Definition) 12 – Certain System Requirements 12 – Regional Code 12 – System Select 13 Remote control 14 Front panel 14 Rear panel 2 Connecting 15 Connecting to Your TV 15 – HDMI Connection 16 – What is SIMPLINK? 16 – Resolution Setting 17 Connecting to an Amplifier 18 – Connecting to an Amplifier via HDMI Output 18 – Connecting to an Amplifier via Digital Audio Output 19 USB device connection 19 – Playback content in the USB device 3 System Setting 20 Settings 20 – Initial Setup 20 – Adjust the Setup Settings 21 – [DISPLAY] Menu 22 – [LANGUAGE] Menu 23 – [AUDIO] Menu 24 – [LOCK] Menu 25 – [OTHERS] Menu 4 Operating 26 General Playback 26 – Using [HOME] menu 26 – Playing a Disc 26 – Playing a file on disc/USB device 27 – Basic operations for video and audio content 27 – Basic operations for photo content 27 – Using the disc menu 28 – Resume playback 28 – Last Scene Memory 28 Advanced Playback 28 – Repeat Playback 29 – Repeating a specific portion 29 – Viewing content information 29 – Changing content list view 30 – Selecting a subtitle file 30 – Options while viewing a photo 31 – Listening to music while slide show 31 On-Screen display 31 – Displaying content information on- screen 32 – Playing from selected time 32 – Selecting a subtitle language 33 – Hearing a different audio 33 – Watching from a different angle 33 – Changing the TV Aspect Ratio 34 – Changing subtitle code page 34 – Changing the Picture Mode 35 Audio CD recording
Table of Contents 7 1 2 3 4 5 6 5 Troubleshooting 36 Troubleshooting 36 – General 37 – Picture 37 – Customer Support 37 – Open source software notice 6 Appendix 38 Controlling a TV with the Supplied Remote Control 38 – Setting up the remote to control your TV 39 Area Code List 40 Language code List 41 Trademarks and Licenses 43 Audio Output Specifications 45 Specifications 46 Maintenance 46 – Handling the Unit 46 – Notes on Discs
Getting Started 8 Getting Started 1 Introduction Playable Discs and symbols used in this manual Media/Term Logo Symbol Description Blu-ray e y y Discs such as movies that can be purchased or rented. y y BD-R/RE discs that are recorded in BDAV format. y u i y y BD-R/RE discs that contain Movie, Music or Photo files. y y ISO 9660+JOLIET, UDF and UDF Bridge format DVD-ROM DVD-R DVD-RW DVD+R DVD+RW (8 cm, 12 cm) r y y Discs such as movies that can be purchased or rented. y y Movie mode and finalized only y y Supports the dual layer disc also o Finalized AVCHD format y u i y y DVD±R/RW discs that contain Movie, Music or Photo files. y y ISO 9660+JOLIET, UDF and UDF Bridge format DVD-RW (VR) (8 cm, 12 cm) r VR mode and finalized only Audio CD (8 cm, 12 cm) t Audio CD CD-R/RW (8 cm, 12 cm) y u i y y CD-R/RW discs that contain Movie, Music or Photo files. y y ISO 9660+JOLIET, UDF and UDF Bridge format Note – , Indicates special notes and operating features. Caution – > Indicates cautions for preventing possible damages from abuse.
Getting Started 9 Getting Started 1 y y Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit. y y Depending on the recording software & the finalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable. y y BD-R/RE, DVD±R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens. y y If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.) y y This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. y y Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-existing conditions to ensure compatible playback. y y Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner. y y You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista) , , Note About the “7” Symbol Display “7”may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media. Compatibility Notes y y Because BD-ROM is a new format, certain disc, digital connection and other compatibility issues are possible. If you experience compatibility problems, please contact an authorized Customer Service Center. y y This unit allows you to enjoy functions such as picture-in-picture, secondary audio and Virtual packages, etc., with BD-ROM supporting BONUSVIEW (BD-ROM version 2 Profile 1 version 1.1). Secondary video and audio can be played from a disc compatible with the picture-in- picture function. For the playback method, refer to the instructions in the disc. y y Viewing high-definition content and up- converting standard DVD content may require a HDMI-capable input or HDCP-capable DVI input on your display device. y y Some BD-ROM and DVD discs may restrict the use of some operation commands or features. y y Dolby TrueHD, Dolby Digital Plus and DTS-HD are supported with maximum 7.1 channels if you use HDMI connection for the audio output of the unit. y y You can use a USB device to store some disc related information. The disc you are using will control how long this information is retained.
Getting Started 10 Getting Started 1 File requirement Movie files File Location File Extension Codec Format Audio Format Subtitle Disc, USB “.avi”,“.divx”, “.mpg”,“.mpeg”, “.mkv”,“.mp4”, “.asf”,“.wmv”, “.m4v”(DRM free),“.vob”, “.3gp” DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx (standard playback only), XVID, MPEG1 SS, H.264/MPEG-4 AVC, MPEG2 PS, MPEG2 TS, VC-1 SM (WMV3) Dolby Digital, DTS, MP3, AAC, AC3 SubRip (.srt / .txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), VobSub (.sub), SubViewer 1.0 (.sub), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt) Music files File Location File Extension Sampling Frequency Bitrate Note Disc, USB “mp3”,“.wav”, “.m4a”(DRM free),“.flac” within 16 - 48 kHz (MP3) within 32 - 320 kbps (MP3) Some wav files are not supported on this player. Photo files File Location File Extension Recommended Size Note Disc, USB “.jpg”,“.jpeg”, “.png”,“.gif” Less than 4,000 x 3,000 x 24 bit/pixel Less than 3,000 x 3,000 x 32 bit/pixel Progressive and lossless compression photo image files are not supported.
Getting Started 11 Getting Started 1 y y The file name is limited to 180 characters. y y Maximum files/Folder: Less than 2000 (total number of files and folders) y y Depending on the size and number of the files, it may take several minutes to read the contents on the media. y y The file requirements on page 10 are not always compatible. There may be some restrictions by file features. y y This unit cannot support the ID3 Tag embedded MP3 file. y y The total playback time of audio files indicated on the screen may not correct for VBR files. y y HD movie files contained on the CD/DVD or USB 1.0/1.1 may not played properly. Blu-ray Disc or USB 2.0 are recommended to play back HD movie files. y y This player supports H.264/MPEG-4 AVC profile Main, High at Level 4.1. For a file with higher level, the warning message will appear on the screen. y y This player does not support files that are recorded with GMC*1 or Qpel*2 . *1 GMC – Global Motion Compensation *2 Qpel – Quarter pixel , , Note y y A“avi”file which is encoded“WMV 9 codec” is not supported. y y This player supports UTF-8 files even if it contains Unicode subtitle contents. This player can not support the pure Unicode subtitle files. y y Depending on the types of file or ways of recording, it may not play back. y y A disc which was recorded by multi-session on normal PC is not supported on this player. y y To be playback a movie file, movie file name and Subtitle file name must be the same. y y If video codec is MPEG2 TS or MPEG2 PS, subtitle does not play back. , , Note AVCHD (Advanced Video Codec High Definition) y y This player can playback AVCHD format discs. These discs are normally recorded and used in camcorders. y y The AVCHD format is a high definition digital video camera format. y y The MPEG-4 AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. y y This player can playback AVCHD discs using “x.v.Colour”format. y y Some AVCHD format discs may not play depending on the recording condition. y y AVCHD format discs need to be finalized. y y “x.v.Colour”offers a wider colour range than normal DVD camcorder discs.
Getting Started 12 Getting Started 1 Certain System Requirements For high definition video playback: y y High definition display that has HDMI input jack. y y BD-ROM disc with high definition content. y y HDMI or HDCP capable DVI input on your display device is required for some content (as specified by disc authors). For Dolby® Digital Plus, Dolby TrueHD and DTS-HD multi-channel audio playback: y y An amplifier/receiver with a built-in (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD) decoder. y y Main, center, surround speakers and subwoofer as necessary for chosen format. Regional Code This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labelled same as the rear of the unit or“ALL”. System Select Open the disc tray using the B (OPEN/CLOSE) button and then, press and hold M (PAUSE) for more than five seconds to change the color system (PAL /NTSC /AUTO).
Getting Started 13 Getting Started 1 Battery Installation Remove the battery cover on the rear of the Remote Control, and insert theR03 (size AAA) battery with 4 and 5 matched correctly. • • • • • • a • • • • • • 1 (POWER): Switches the player ON or OFF. B (OPEN/CLOSE): Opens and closes the disc tray. 0-9 numerical buttons: Selects numbered options in a menu. CLEAR: Removes a mark on the search menu or a number when setting the password. TV Control Buttons: See page 38. • • • • • • b • • • • • • c/v (SCAN): Searches backward or forward. C/V (SKIP): Goes to the next or previous chapter / track / file. M (PAUSE): Pauses playback. z (PLAY): Starts playback. Z (STOP): Stops playback. • • • • • • c • • • • • • HOME (n): Displays or exits the [Home Menu]. INFO/MENU (m): Displays or exits On-Screen Display. Direction buttons: Selects an option in the menu. ENTER (b): Acknowledges menu selection. BACK (1): Exits the menu or returns to the previous screen. DISC MENU: Accesses menu on a disc. • • • • • • d • • • • • • REPEAT (h): Repeats a desired section or sequence. AUDIO ([): Selects an audio language. SUBTITLE (]): Selects a subtitle language. TITLE/POP-UP: Displays the DVD title menu or BD-ROM’s pop-up menu, if available. Colored (R, G, Y, B) buttons: Use to navigate BD-ROM menus. They are also used for [MOVIE], [PHOTO] and [MUSIC] menu. Remote control
Getting Started 14 Getting Started 1 Front panel a Disc Tray b Display Window c Remote Sensor d B (OPEN/CLOSE) e N (PLAY / PAUSE) f Z (STOP) g 1 (POWER) h USB Port Rear panel a AC power cord b HDMI OUT c DIGITAL AUDIO OUT (COAXIAL)
Connecting 15 Connecting 2 Connecting to Your TV HDMI Connection If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High Speed HDMI™ Cable). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor. Rear of the unit TV HDMI cable Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Additional Information for HDMI y y When you connect a HDMI or DVI compatible device make sure of the following: - - Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player. - - The connected device’s video input is set correctly for this unit. - - The connected device is compatible with 720x576p, 1280x720p, 1920x1080i or 1920x1080p video input. y y Not all HDCP-compatible HDMI or DVI devices will work with this player. - - The picture will not be displayed properly with non-HDCP device. y y If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output. y y When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to“Resolution Setting”on page 16) y y Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 22). y y Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again. y y When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable. y y If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m(15 ft.)). , , Note
Connecting 16 Connecting 2 What is SIMPLINK? Some functions of this unit can be controlled by the TV’s remote control when this unit and a compatible LG TV with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc. Refer to the TV owner’s manual for the details of SIMPLINK function. LG TV’s with SIMPLINK function has the logo as shown above. Depending on the disc type or playing status, some SIMPLINK operations may differ from your purpose or not work. , , Note Resolution Setting The player provides several output resolutions for HDMI OUT jack. You can change the resolution using [Setup] menu. 1. Press HOME (n). 2. Use a/d to select the [Setup] and press ENTER (b). The [Setup] menu appears. 3. Use w/s to select [DISPLAY] option then press d to move to the second level. 4. Use w/s to select the [Resolution] option then press ENTER (b) to move to the third level. 5. Use w/s to select the desired resolution then press ENTER (b) to confirm your selection.
Connecting 17 Connecting 2 y y If your TV does not accept the resolution you have set on the player, you can set resolution to 576p as follows: 1. Press B to open the disc tray. 2 Press Z (STOP) for more than 5 seconds. y y When you set the resolution to 576i with HDMI connection, actual resolution is outputted to 576p. y y If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto]. y y If you select a resolution that your TV does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution. y y The 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc. , , Note Connecting to an Amplifier Make one of the following connections, depending on the capabilities of your existing equipment. y y HDMI Audio connection (page 18) y y Digital Audio connection (page 18) Since many factors affect the type of audio output, see“Audio Output Specifications”for details (pages 43). About Digital Multi-channel sound A digital multi-channel connection provides the best sound quality. For this, you need a multi- channel Audio/Video Receiver that supports one or more of the audio formats supported by your player. Check the logos on the front of the Audio/ Video receiver and the manual. (PCM Stereo, PCM Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and/or DTS-HD)
Connecting 18 Connecting 2 Connecting to an Amplifier via HDMI Output Connect the player’s HDMI OUT jack to the corresponding in jack on your amplifier using a HDMI cable. HDMI cable HDMI cable TV Receiver/Amplifier Rear of the unit Connect the amplifier’s HDMI output jack to HDMI input jack on your TV using a HDMI cable if your amplifier has HDMI output jack. You will need to activate the player’s digital output. (See“[AUDIO] Menu”on pages 23) Connecting to an Amplifier via Digital Audio Output Connect the player’s DIGITAL AUDIO OUT jack to the corresponding in jack (COAXIAL) on your amplifier using an optional digital audio cable. Coaxial cable Receiver/Amplifier Rear of the unit You will need to activate the player’s digital output. (See“[AUDIO] Menu”on pages 23.)
Connecting 19 Connecting 2 USB device connection This player can play movie, music and photo files contained in the USB device. Playback content in the USB device 1. Insert a USB device to the USB port until it fits into place. When you connect the USB device on the HOME menu, the player plays a music file contained in the USB storage device automatically. If the USB storage device is containing various types of files, a menu for the file type selection will appear. File loading may takes few minutes depending on the number of content stored in the USB storage device. Press ENTER (b) while [Cancel] is selected to stop loading. 2. Press HOME (n). 3. Select [Movie], [Photo] or [Music] using a/d, and press ENTER (b). 4. Select the [USB] option using w/s, and press ENTER (b). 5. Select a file using w/s/a/d, and press PLAY or ENTER (b) to play the file. 6. Withdraw the USB device carefully. y y This player supports USB flash drive/external HDD formatted in FAT16, FAT32 and NTFS when accessing files (music, photo, movie). However, for Blu-ray contents, only FAT16 and FAT32 formats are supported. Use the USB flash drive/external HDD formatted in either FAT16 or FAT32 when enjoying Blu-ray contents. y y This unit can support up to 4 partitions of the USB device. y y Do not extract the USB device during operation (play, etc.). y y A USB device which requires additional program installation when you have connected it to a computer, is not supported. y y USB device: USB device that supports USB1.1 and USB2.0. y y Movie, music and photo files can be played. For details of operations on each file, refer to relevant pages. y y Regular back up is recommended to prevent data loss. y y If you use a USB extension cable, USB HUB or USB Multi-reader, the USB device may not be recognized. y y Some USB device may not work with this unit. y y Digital camera and mobile phone are not supported. y y USB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device. , , Note
System Setting 20 System Setting 3 Settings Initial Setup When you turn on the unit for the first time, the initial setup wizard appears on the screen. Set the display language on the initial setup wizard. 1. Press 1 (POWER). The initial setup wizard appears on the screen. 2. Use w/s/a/d to select a display language and press ENTER (b). 3. Check the setting that you have set in the previous step. Press ENTER (b) while [Finish] is highlighted to finish the initial setup settings. If there is any settings to be changed, use a/d to select [Previous] and press ENTER (b). Adjust the Setup Settings You can change the settings of the player in the [Setup] menu. 1. Press HOME (n). 2. Use a/d to select the [Setup] and press ENTER (b). The [Setup] menu appears. 3. Use w/s to select the first setup option, and press d to move to the second level. 4. Use w/s to select a second setup option, and press ENTER (b) to move to the third level. 5. Use w/s to select a desired setting, and press ENTER (b) to confirm your selection.
System Setting 21 System Setting 3 [DISPLAY] Menu TV Aspect Ratio Select a TV aspect ratio option according to your TV type. [4:3 Letter Box] Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture. [4:3 Pan Scan] Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both sides of the picture are cut off. [16:9 Original] Select when a 16:9 wide TV is connected. The 4:3 picture is displayed with an original 4:3 aspect ratio, with black bars appearing at the left and right sides. [16:9 Full] Select when a 16:9 wide TV is connected. The 4:3 picture is adjusted horizontally (in a linear proportion) to fill the entire screen. You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p. , , Note Resolution Sets the output resolution of the HDMI video signal. Refer to page 16 for details about the resolution setting. [Auto] If the HDMI OUT jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. [1080p] Outputs 1080 lines of progressive video. [1080i] Outputs 1080 lines of interlaced video. [720p] Outputs 720 lines of progressive video. [576p] Outputs 576 lines of progressive video. [576i] Outputs 576 lines of interlaced video. 1080p Display Mode When the resolution is set to 1080p, select [24 Hz] for smooth presentation of film material (1080p/24 Hz) with a HDMI-equipped display compatible with 1080p/24 Hz input. y y When you select [24 Hz], you may experience some picture disturbance when the video switches video and film material. In this case, select [50 Hz]. y y Even when [1080p Display Mode] is set to [24 Hz], if your TV is not compatible with 1080p/24 Hz, the actual frame frequency of the video output will be 50 Hz to match the video source format. , , Note
System Setting 22 System Setting 3 HDMI Color Setting Select the type of output from the HDMI OUT jack. For this setting, please refer to the manuals of your display device. [YCbCr] Select when connecting to a HDMI display device. [RGB] Select when connecting to a DVI display device. Home Menu Guide This function allows you to display or delete the guide bubble on the Home Menu. Set this option to [On] for displaying guide. [LANGUAGE] Menu Display Menu Select a language for the [Setup] menu and on- screen display. Disc Menu/Disc Audio/ Disc Subtitle Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. [Original] Refers to the original language in which the disc was recorded. [Other] Press ENTER (b) to select another language. Use number buttons then press ENTER (b) to enter the corresponding 4-digit number according to the language code list on page 40. [Off] (Disc Subtitle only) Turn off Subtitle. Depending on the disc, your language setting may not work. , , Note
System Setting 23 System Setting 3 [AUDIO] Menu Each disc has a variety of audio output options. Set the player’s Audio options according to the type of audio system you use. Since many factors affect the type of audio output, see“Audio Output Specifications”on page 43 for details. , , Note Digital Output [PCM Stereo] (HDMI, COAXIAL) Select if you connect this unit’s HDMI OUT or DIGITAL AUDIO OUT jack to a device with two- channel digital stereo decoder. [PCM Multi-Ch] (HDMI only) Select if you connect this unit’s HDMI OUT jack to a device with multi-channel digital decoder. [DTS Re-Encode] (HDMI, COAXIAL) Select if you connect this unit’s HDMI OUT or DIGITAL AUDIO OUT jack to a device with DTS decoder. [BitStream] (HDMI, COAXIAL) Select if you connect this unit’s DIGITAL AUDIO OUT and HDMI OUT jack to a device with LPCM, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and DTS-HD decoder. y y When [Digital Output] option is set to [PCM Multi-Ch], the audio may output as PCM Stereo if the PCM Multi-Ch information is not detected from HDMI device with EDID. y y If the [Digital Output] option is set to [DTS Re-Encode], the DTS Re-Encode audio is outputted for BD-ROM discs with secondary audio and the original audio is outputted for the other discs (like [BitStream]). , , Note Sampling Freq. (Digital Audio Output) [192 kHz] Select this if your A/V Receiver or Amplifier is capable of handling 192 kHz signals. [96 kHz] Select this if your A/V Receiver or Amplifier is not capable of handling 192 kHz signals. When this choice is made, this unit automatically converts any 192 kHz signals to 96 kHz so your system can decode them. [48 kHz] Select this if your A/V Receiver or Amplifier is not capable of handling 192 kHz and 96 kHz signal. When this choice is made, this unit automatically converts any 192 kHz and 96 kHz signals to 48 kHz so your system can decode them. Check the documentation for your A/V Receiver or Amplifier to verify its capabilities. DRC (Dynamic Range Control) This function allows you to listen to a movie at a lower volume without losing clarity of sound. [Off] Turns off this function. [On] Compress the dynamic range of the Dolby Digital, Dolby Digital Plus or Dolby TrueHD audio output. [Auto] The dynamic range of the Dolby TrueHD audio output is specified by itself. And the dynamic range of the Dolby Digital and Dolby Digital Plus are operated as same as the [On] mode. The DRC setting can only be changed when the unit is in“NO DISC”status or the unit is in complete stop mode. , , Note
System Setting 24 System Setting 3 [LOCK] Menu The [LOCK] settings affect only BD-ROM and DVD playback. To access the any features in [LOCK] settings, you must enter the 4-digit security code you have created. If you have not entered a password yet, you are prompted to do so. Enter a 4-digit password twice, and press ENTER (b) to create a new password. Password You can create or change the password. [None] Enter a 4-digit password twice, and press ENTER (b) to create a new password. [Change] Enter the current password and press ENTER (b). Enter a 4-digit password twice, and press ENTER (b) to create a new password. If you forget your password If you forget your password, you can clear it using the following steps: 1. Remove any disc that might be in the player. 2. Select [Password] option in the [Setup] menu. 3. Use Number buttons to enter“210499”. The password is cleared. If you make a mistake before pressing ENTER (b), press CLEAR. Then input the correct password. , , Note DVD Rating Blocks playback of rated DVD based on their content. (Not all discs are rated.) [Rating 1-8] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. [Unlock] If you select [Unlock], parental control is not active and the disc plays in full. Blu-ray Disc Rating Set an age limit of BD-ROM play. Use number buttons to input an age limit for BD-ROM viewing.  All BD-ROM can be played. [0-254] Prohibits play of BD-ROM with corresponding ratings recorded on them. y y The [Blu-ray Disc Rating] will be applied only for the Blu-ray disc that containing the Advanced Rating Control. , , Note Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 39.
System Setting 25 System Setting 3 [OTHERS] Menu DivX® VOD ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration. [Register] Displays the registration code of your player. [Deregister] Deactivate your player and display the deactivation code. All the downloaded videos from DivX(R) VOD with this player’s registration code can only be played on this unit. , , Note Auto Power Off The screen saver appears when you leave the player in Stop mode for about five minutes. If you set this option to [On], the unit automatically turns off within 20 minutes since the Screen Saver is displayed. Set this option to [Off] to leave the screen saver until the unit is operated by the user. Initialize [Factory Set] You can reset the player to its original factory settings. [Blu-ray Storage Clear] Initializes the Blu-ray contents from the connected USB storage. Software [Information] Displays the current software version.
4 Operating Operating 26 Operating 4 General Playback Using [HOME] menu The home menu appears when you press HOME (n). Use a/d to select a category and press ENTER (b). a [Movie] - Plays video contents. b [Photo] - Plays photo contents. c [Music] - Plays audio contents. d [Setup] - Adjusts the system settings. Playing a Disc erot 1. Press B (OPEN/CLOSE), and place a disc on the disc tray. 2. Press B (OPEN/CLOSE) to close the disc tray. For most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically. 3. Press HOME (n). 4. Select [Movie] or [Music] using a/d, and press ENTER (b). 5. Select [Blu-ray Disc], [DVD], [VR] or [Audio] option using w/s, and press ENTER (b). y y Playback functions described in this manual are not always available with every file and media. Some functions can be restricted depending on many factors. y y Depending on the BD-ROM titles, a USB device connection may be needed for the proper playback. y y Unfinalized DVD-VR format discs may not be played in this player. y y Some DVD-VR discs are made with CPRM data by DVD RECORDER. This unit cannot support these kinds of discs. , , Note Playing a file on disc/USB device yui This player can play movie, music and photo files contained in the disc or USB device. 1. Insert a data disc on the tray or connect a USB device. 2. Press HOME (n). 3. Select [Movie], [Photo] or [Music] using a/d, and press ENTER (b). 4. Select [Data] or [USB] option using w/s, and press ENTER (b). 5. Select a file using w/s/a/d, and press d(PLAY) or ENTER (b) to play the file.
Operating 27 Operating 4 Basic operations for video and audio content To stop playback Press Z (STOP) while playback. To pause playback Press M (PAUSE) while playback. Press z (PLAY) to resume playback. To play frame-by-frame (Video) Press M (PAUSE) while movie playback. Press M (PAUSE) repeatedly to play Frame-by-Frame playback. To scan forward or backward Press c or v to play fast forward or fast reverse during playback. You can change the various playback speeds by pressing c or v repeatedly. To slow down the playing speed While the playback is paused, press v repeatedly to play various speeds of slow motion. To skip to the next/previous chapter/track/file During playback, press C or V to go to the next chapter/track/file or to return to the beginning of the current chapter/track/file. Press C twice briefly to step back to the previous chapter/track/file. Basic operations for photo content To play a slide show Press z (PLAY) to start slide show. To stop a slide show Press Z (STOP) while slide show. To pause a slide show Press M (PAUSE) while slide show. Press z (PLAY) to re-start the slide show. To skip to the next/previous photo While viewing a photo in full screen, press a or d to go to the previous or next photo. Using the disc menu ero To display the disc menu The menu screen may be displayed first after loading a disc which contains a menu. If you want to display the disc menu while playback, press DISC MENU. Use w/s/a/d buttons to navigate through menu items. To display the Pop-up menu Some BD-ROM discs contain Pop-up menu that appears while playback. Press TITLE/POPUP while playback, and use w/s/ a/d buttons to navigate through menu items.
Operating 28 Operating 4 Resume playback eroyt u The unit records the point where you pressed the Z (STOP) depending on the disc. If“MZ (Resume Stop)”appears on the screen briefly, press z (PLAY) to resume playback (from the scene point). If you press Z (STOP) twice or unload the disc, “Z(Complete Stop)”appears on the screen. The unit will clear the stopped point. y y The resume point may be cleared when a button is pressed (for example; 1 (POWER), B (OPEN/CLOSE), etc). y y On BD-ROM discs with BD-J, the resume playback function does not work. y y If you press Z (STOP) once during BD-ROM interactive title playback, the unit will be in Complete Stop mode. , , Note Last Scene Memory er This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. y y Last Scene Memory function for a previous disc is erased once a different disc is played. y y This function may not work depending on the disc. y y On BD-ROM discs with BD-J, the last scene memory function does not work. y y This unit does not memorize settings of a disc if you switch off the unit before commencing to play it. , , Note Advanced Playback Repeat Playback erotu y During playback, press REPEAT (h) repeatedly to select a desired repeat mode. Blu-ray Disc / DVD / Movie files jA- – Selected portion will be repeated continually. jChapter – The current chapter will be played back repeatedly. jTitle – The current title will be played back repeatedly. jAll – All the tracks or files will be played back repeatedly. To return to normal playback, press REPEAT (h) repeatedly to select [Off]. Audio CDs/Music files ;Track– The current track or file will be played back repeatedly. :All – All the tracks or files will be played back repeatedly. l – The tracks or files will be played back in random order. l:All – All the tracks or files will be played back repeatedly in random order. kA-B – Selected portion will be repeated continually. (Audio CD only) To return to normal playback, press CLEAR. y y If you press V once during Repeat Chapter/Track playback, the repeat playback cancels. y y This function may not work on some disc or title. , , Note
Operating 29 Operating 4 Repeating a specific portion erot This player can repeat a portion you have selected. 1. While playback, press REPEAT (h) to select [A-] at the beginning of the portion you wish to repeat. 2. Press ENTER (b) at the end of the portion. Your selected portion will be repeated continually. 3. To return to normal playback, press REPEAT (h) repeatedly to select [Off]. y y You cannot select a portion less than 3 seconds. y y This function may not work on some disc or title. , , Note Viewing content information y The player can display the content information. 1. Select a file using w/s/a/d. 2. Press INFO/MENU (m) to display the option menu. 3. Select the [Information] option using w/s, and press ENTER (b). The file information appears on the screen. While movie playback, you can display the file information by pressing TITLE/POPUP. The information displayed on the screen may not correct comparing actual content information. , , Note Changing content list view yui On the [Movie], [Music] or [Photo] menu, you can change the content list view. Method 1 Press red (R) coloured button repeatedly. Method 2 1. On the content list, press INFO/MENU (m) to display the option menu. 2. Use w/s to select the [View Change] option. 3. Press ENTER (b) to change the content list view.
Operating 30 Operating 4 Selecting a subtitle file y If the subtitle file name is different from the movie file name, you need to select the subtitle file on the [Movie] menu before playing the movie. 1. Use w/s/a/d to select the subtitle file you wish to play in the [Movie] menu. 2. Press ENTER (b). Press ENTER (b) again to deselect the subtitle file. Selected subtitle file will be displayed when you play the movie file. If you press Z (STOP) while playback, the subtitle selection is cancelled. , , Note Options while viewing a photo i You can use various options during viewing a photo in full screen. 1. While viewing a photo in full screen, press INFO/ MENU (m) to display the option menu. 2. Select an option using w/s. a Current photo/Total number of photos – Use a/d to view previous/next photo. b Slide Show – Press ENTER (b) to start or pause slide show. c Music Select – Select the background music for the slide show (page 31). d Music –Press ENTER (b) to start or pause background music. e Rotate – Press ENTER (b) to rotate the photo clockwise. f Zoom – Press ENTER (b) to display the [Zoom] menu. g Effect – Use a/d to select a transition effect between photos in a slide show. h Speed – Use a/d to select a delaying speed between photos in a slide show. 3. Press BACK (1) to exit the option menu.
Operating 31 Operating 4 Listening to music while slide show i You can display photo files while listening to music files. 1. While viewing a photo in full screen, press INFO/ MENU (m) to display the option menu. 2. Use w/s to select [Music Select] option, and press ENTER (b) to display the [Music Select] menu. 3. Use w/s to select a device, and press ENTER (b). 4. Use w/s to select a file or a folder you wish to play. Select g and press ENTER (b) to display the upper directory. 5. Use d to select [OK], and press ENTER (b) to complete music selection. On-Screen display You can display and adjust various information and settings about the content. Displaying content information on-screen eroy 1. While playback, press INFO/MENU (m) to show various playback information. a Title – current title number/total number of titles b Chapter – current chapter number/total number of chapters c Time – elapsed playing time/total playback time d Audio – selected audio language or channel e Subtitle – selected subtitle. f Angle – selected angle/total number of angles g TV Aspect Ratio – selected TV aspect Ratio h Picture Mode – selected picture mode
Operating 32 Operating 4 2. Select an option using w/s. 3. Use a/d to adjust the selected option value. 4. Press BACK (1) to exit the On-Screen display. y y If no button is pressed for a few seconds, the on-screen display disappears. y y A title number cannot be selected on some discs. y y Available items may differ depending on discs or titles. y y If an interactive Blu-ray Disc is playing back, some setting information is displayed on the screen but prohibited to be changed. , , Note Playing from selected time eroy 1. Press INFO/MENU (m) during playback. The time search box shows the elapsed playing time. 2. Select the [Time] option and then input the required start time in hours, minutes, and seconds from left to right. For example, to find a scene at 2 hours, 10 minutes, and 20 seconds, enter“21020”. Press a/d to skip the playback 60 seconds forward or backward. 3. Press ENTER (b) to start playback from selected time. y y This function may not work on some disc or titles. , , Note Selecting a subtitle language eroy 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [Subtitle] option. 3. Use a/d to select desired subtitle language. 4. Press BACK (1) to exit the On-Screen display. y y Some discs allow you to change subtitle selections only via the disc menu. If this is the case, press TITLE/POPUP or DISC MENU button and choose the appropriate subtitle from the selections on the disc menu. y y You can select the [Subtitle] option on the On-Screen display directely by pressing SUBTITLE (]) button. , , Note
Operating 33 Operating 4 Hearing a different audio eroy 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [Audio] option. 3. Use a/d to select desired audio language, audio track or audio channel. y y Some discs allow you to change audio selections only via the disc menu. In this case, press TITLE/POP-UP or DISC MENU button and choose the appropriate audio from the selections on the disc menu. y y Immediately after you have switched sound, there may be a temporary discrepancy between the display and actual sound. y y On BD-ROM disc, the multi audio format (5.1CH or 7.1CH) is displayed with [MultiCH] in the on-screen display. y y You can select the [Audio] option on the On-Screen display directely by pressing AUDIO ([) button. , , Note Watching from a different angle er If the disc contains scenes recorded at different camera angles, you can change to a different camera angle during playback. 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [Angle] option. 3. Use a/d to select desired angle. 4. Press BACK (1) to exit the On-Screen display. Changing the TV Aspect Ratio eoy You can change the TV aspect ratio setting while playback. 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [TV Aspect Ratio] option. 3. Use a/d to select desired option. 4. Press BACK (1) to exit the On-Screen display. Even if you change the value of the [TV Aspect Ratio] option in On-Screen display, the [TV Aspect Ratio] option in the [Setup] menu is not changed. , , Note
Operating 34 Operating 4 Changing subtitle code page y If the subtitle is displayed in broken letter, you can change the subtitle code page to view the subtitle file properly. 1. During playback, press INFO/MENU (m) to display the playback menu. 2. Use w/s to select the [Code Page] option. 3. Use a/d to select desired code option. 4. Press BACK (1) to exit the On-Screen display. Changing the Picture Mode eroy You can change the [Picture mode] option while playback. 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [Picture Mode] option. 3. Use a/d to select desired option. 4. Press BACK (1) to exit the On-Screen display. Setting the [User setting] option 1. During playback, press INFO/MENU (m) to display the On-Screen display. 2. Use w/s to select the [Picture Mode] option. 3. Use a/d to select the [User setting] option, and press ENTER (b). 4. Use w/s/a/d to adjust the [Picture Mode] options. Select [Default] option then press ENTER (b) to reset the all video adjustments. 5. Use w/s/a/d to select the [Close] option, and press ENTER (b) to finish setting.
Operating 35 Operating 4 Audio CD recording You can record one desired track or all of the tracks in Audio CD to a USB storage device. 1. Insert a USB storage device to the USB port on the front panel. 2. Press B (OPEN/CLOSE), and place an Audio CD on the disc tray. Press B (OPEN/CLOSE) to close the disc tray. The playback starts automatically. 3. Press INFO/MENU (m) to display the option menu. 4. Use w/s to select [CD Recording] option, and press ENTER (b). 5. Use w/s to select a track you wish to copy on the menu, and press ENTER (b). Repeat this step to select tracks as many as you can. Selects all the tracks on an Audio CD. Selects an encoding option from the pop-up menu (128kbps, 192kbps or 320kbps). Cancels the recording and returns to the previous screen. 6. Use w/s/a/d to select [Start], and press ENTER (b). 7. Use w/s/a/d to select a destination folder to be copied. If you want to create a new folder, use w/s/a/d to select [New Folder] and press ENTER (b). Enter a folder name using virtual keyboard, and press ENTER (b) while [OK] is selected. 8. Use w/s/a/d to select [OK], and press ENTER (b) to start Audio CD recording. If you want to stop in progressing Audio CD recording, press ENTER (b) while [Cancel] is highlighted. 9. A message appears when Audio CD recording is completed. Press ENTER (b) to check the audio file created in the destination folder. y y The table below shows the average recording time from an audio track with 4 minutes of playback time to an audio file with 192 kbps as an example. stop mode while playback 1 min. 4 min. y y Recording times in the table above are approximate. y y Actual recording time for USB storage device varies depending on the USB storage device’s ability. y y Make sure that there is minimum of 50 MB free space is needed when recording into the USB storage device. y y The length of the audio should be longer than 20 seconds for the proper recording. y y Do not turn off this player or extract the connected USB storage device during Audio CD recording. , , Note The recording or copying features on this player are provided for your personal and non-commercial use. The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. LG expressly disclaims any responsibility for illegal distribution or use of unauthorized content in commercial purpose. Be Responsible Respect Copyrights > >Caution
5 Troubleshooting Troubleshooting 36 Troubleshooting 5 Troubleshooting General Symptom Cause & Solution The Power does not turned on. y y Plug the power cord into the wall outlet securely. The unit does not start playback. y y Insert a playable disc. (Check the disc type, colour system, and regional code.) y y Place the disc with the playback side down. y y Place the disc on the disc tray correctly inside the guide. y y Clean the disc. y y Cancel the Rating function or change the rating level. The angle cannot be changed. y y Multi-angles are not recorded on the DVD Video being played. Cannot play movie, photo or music files. y y The files are not recorded in a format that the unit can play. y y The unit does not support the codec of the movie file. The remote control does not work properly. y y The remote control is not pointed at the remote sensor of the unit. y y The remote control is too far from the unit. y y There is an obstacle in the path of the remote control and the unit. y y The battery in the remote control is exhausted. The unit is plugged in, but the power will not turn on or off. You can reset the unit as follows. y y Unplug the power cord, wait at least five seconds, and then plug it in again. The unit is not operating normally.
Troubleshooting 37 Troubleshooting 5 Picture Symptom Cause & Solution There is no picture. y y Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen. y y Connect the video connection securely. y y Check the [HDMI Color Setting] in the [Setup] menu is set to the appropriate item that conforms to your video connection. y y Your TV may not support the resolution you have set on the player. Change the resolution that your TV accepts. y y The player’s HDMI OUT jack is connected to a DVI device that does not support copyright protection. Picture noise appears. y y You are playing a disc recorded in a colour system that is different from your TV. y y Set the resolution which your TV accepts. Customer Support You can update the Player using the latest software to enhance the products operation and/or add new features. To obtain the latest software for this player (if updates have been made), please visit http://www.lg.com/global/support or contact LG Electronics customer care centre. Open source software notice To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are available to download with the source code.
Appendix 38 Appendix 6 Controlling a TV with the Supplied Remote Control You can control your TV using the buttons below. By pressing You can 1 (TV POWER) Turn the TV on or off. PR/CH +/– Scan up or down through memorized channels. VOL +/– Adjust the volume of the TV AV/INPUT Switch the TV’s input source between the TV and other input sources. VOL +/– Adjust the volume of the TV Depending on the unit being connected, you may not be able to control your TV using some of the buttons. , , Note Setting up the remote to control your TV You can operate your TV with the supplied remote control. If your TV is listed in the table below, set the appropriate manufacturer code. 1. While holding down 1 (TV POWER) button, and press the manufacturer code for your TV with the numerical buttons (see the table below). Manufacturer Code Number LG 1(Default), 2 Zenith 1, 3, 4 GoldStar 1, 2 Samsung 6, 7 Sony 8, 9 Hitachi 4 2. Release the 1 (TV POWER) button to complete setting. Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again.
Appendix 39 Appendix 6 Area Code List Choose an area code from this list. Area Code Area Code Area Code Area Code Afghanistan AF Argentina AR Australia AU Austria AT Belgium BE Bhutan BT Bolivia BO Brazil BR Cambodia KH Canada CA Chile CL China CN Colombia CO Congo CG Costa Rica CR Croatia HR Czech Republic CZ Denmark DK Ecuador EC Egypt EG El Salvador SV Ethiopia ET Fiji FJ Finland FI France FR Germany DE Great Britain GB Greece GR Greenland GL Hong Kong HK Hungary HU India IN Indonesia ID Israel IL Italy IT Jamaica JM Japan JP Kenya KE Kuwait KW Libya LY Luxembourg LU Malaysia MY Maldives MV Mexico MX Monaco MC Mongolia MN Morocco MA Nepal NP Netherlands NL Antilles AN New Zealand NZ Nigeria NG Norway NO Oman OM Pakistan PK Panama PA Paraguay PY Philippines PH Poland PL Portugal PT Romania RO Russian Federation RU Saudi Arabia SA Senegal SN Singapore SG Slovak Republic SK Slovenia SI South Africa ZA South Korea KR Spain ES Sri Lanka LK Sweden SE Switzerland CH Taiwan TW Thailand TH Turkey TR Uganda UG Ukraine UA United States US Uruguay UY Uzbekistan UZ Vietnam VN Zimbabwe ZW
Appendix 40 Appendix 6 Language code List Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu]. Language Code Language Code Language Code Language Code Afar 6565 Afrikaans 6570 Albanian 8381 Amharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Aymara 6588 Azerbaijani 6590 Bashkir 6665 Basque 6985 Bengali; Bangla 6678 Bhutani 6890 Bihari 6672 Breton 6682 Bulgarian 6671 Burmese 7789 Byelorussian 6669 Chinese 9072 Croatian 7282 Czech 6783 Danish 6865 Dutch 7876 English 6978 Esperanto 6979 Estonian 6984 Faroese 7079 Fiji 7074 Finnish 7073 French 7082 Frisian 7089 Galician 7176 Georgian 7565 German 6869 Greek 6976 Greenlandic 7576 Guarani 7178 Gujarati 7185 Hausa 7265 Hebrew 7387 Hindi 7273 Hungarian 7285 Icelandic 7383 Indonesian 7378 Interlingua 7365 Irish 7165 Italian 7384 Japanese 7465 Kannada 7578 Kashmiri 7583 Kazakh 7575 Kirghiz 7589 Korean 7579 Kurdish 7585 Laotian 7679 Latin 7665 Latvian, Lettish 7686 Lingala 7678 Lithuanian 7684 Macedonian 7775 Malagasy 7771 Malay 7783 Malayalam 7776 Maori 7773 Marathi 7782 Moldavian 7779 Mongolian 7778 Nauru 7865 Nepali 7869 Norwegian 7879 Oriya 7982 Panjabi 8065 Pashto, Pushto 8083 Persian 7065 Polish 8076 Portuguese 8084 Quechua 8185 Rhaeto-Romance 8277 Rumanian 8279 Russian 8285 Samoan 8377 Sanskrit 8365 Scots Gaelic 7168 Serbian 8382 Serbo-Croatian 8372 Shona 8378 Sindhi 8368 Singhalese 8373 Slovak 8375 Slovenian 8376 Spanish 6983 Sudanese 8385 Swahili 8387 Swedish 8386 Tagalog 8476 Tajik 8471 Tamil 8465 Telugu 8469 Thai 8472 Tonga 8479 Turkish 8482 Turkmen 8475 Twi 8487 Ukrainian 8575 Urdu 8582 Uzbek 8590 Vietnamese 8673 Volapük 8679 Welsh 6789 Wolof 8779 Xhosa 8872 Yiddish 7473 Yoruba 8979 Zulu 9085
Appendix 41 Appendix 6 Trademarks and Licenses Blu-ray Disc™, Blu-ray™, BONUSVIEW™ and the logos are trademarks of the Blu-ray Disc Association. “DVD Logo”is a trademark of DVD Format/Logo Licensing Corporation. Java is a trademark of Oracle and/or its affiliates. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. “x.v.Colour”is a trademark of Sony Corporation. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. “AVCHD”and the“AVCHD”logo are trademarks of Panasonic Corporation and Sony Corporation. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.
Appendix 42 Appendix 6 Cinavia Notice This product uses Cinavia technology to limit the use of unauthorized copies of some commercially- produced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted. More information about Cinavia technology is provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA. This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.
Appendix 43 Appendix 6 Audio Output Specifications Jack/Setting Source COAXIAL (DIGITAL AUDIO OUT) *3 PCM Stereo DTS Re-encode *4 BitStream Dolby Digital PCM 2ch DTS Dolby Digital Dolby Digital Plus PCM 2ch DTS Dolby Digital Dolby TrueHD PCM 2ch DTS Dolby Digital DTS PCM 2ch DTS DTS DTS-HD PCM 2ch DTS DTS Linear PCM 2ch PCM 2ch DTS PCM 2ch Linear PCM 5.1ch PCM 2ch DTS PCM 2ch Linear PCM 7.1ch PCM 2ch DTS PCM 2ch Jack/Setting Source HDMI OUT PCM Stereo PCM Multi-Ch DTS Re-encode *4 BitStream*1 *2 Dolby Digital PCM 2ch PCM 2ch DTS Dolby Digital Dolby Digital Plus PCM 2ch PCM 2ch DTS Dolby Digital Plus Dolby TrueHD PCM 2ch PCM 2ch DTS Dolby TrueHD DTS PCM 2ch PCM 2ch DTS DTS DTS-HD PCM 2ch PCM 2ch DTS DTS-HD Linear PCM 2ch PCM 2ch PCM 2ch DTS Linear PCM 2ch Linear PCM 5.1ch PCM 2ch PCM 5.1ch DTS Linear PCM 5.1ch Linear PCM 7.1ch PCM 2ch PCM 7.1ch DTS Linear PCM 7.1ch *1 The secondary and interactive audio may not be included in the output bitstream if [Digital Output] option is set to [BitStream]. (Except LPCM Codec : the output always include interactive and secondary audio.) *2 This player automatically selects the HDMI audio according to the decoding capability of the connected HDMI device even though [Digital Output] option is set to [BitStream]. *3 On the PCM audio output, the sampling frequency of DIGITAL AUDIO OUT is limited to 96 kHz. *4 If the [Digital Output] option is set to [DTS re- encode], the audio output is limited to 48 kHz and 5.1Ch. If the [Digital Output] option is set to [DTS re-encode], the DTS Re-encode audio is outputted for BD-ROM discs, and the original audio is outputted for the other discs (like [BitStream]). y y If the HDMI OUT jack is connected to your TV with High Speed HDMI™ Cable and Dolby Digital Plus/Dolby TrueHD is outputted from HDMI OUT jack, DIGITAL AUDIO OUT jack is limited to“PCM 2ch”(When the HDMI and DIGITAL AUDIO OUT are connected simultaneously).
Appendix 44 Appendix 6 y y The audio is outputted as PCM 48 kHz/16 bit for MP3/WMA file and PCM 44.1kHz/16 bit for Audio CD while playback. y y You must select a digital audio output and a maximum sampling frequency that your Amplifier (or AV receiver) accepts using [Digital Output] and [Sampling Freq.] options on the [Setup] menu (see page 23). y y With digital audio connection (DIGITAL AUDIO OUT or HDMI OUT), Disc Menu button sounds of BD-ROM may not be heard if the [Digital Output] option is set to [BitStream]. y y If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all. y y Multi-channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder.
Appendix 45 Appendix 6 Specifications General Power requirements Refer to main label on the rear panel. Power consumption 12 W Dimensions (W x H x D) Approx. 360 x 41 x 190 mm Net Weight (Approx.) 1.3 Kg Operating temperature 5 °C to 35 °C Operating humidity 5 % to 90 % Outputs HDMI OUT (video/audio) 19 pin (Type A, HDMI™ Connector) DIGITAL AUDIO OUT (COAXIAL) 0.5 V (p-p), 75 Ω, RCA jack x 1 System Laser Semiconductor laser wavelength 405 nm / 650 nm Signal system Standard PAL/NTSC colour TV system Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling) Harmonic distortion Less than 0.02 % Dynamic range More than 95 dB Bus Power Supply (USB) DC 5 V 0 500 mA y y Design and specifications are subject to change without notice.
Appendix 46 Appendix 6 Maintenance Handling the Unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Keeping the exterior surfaces clean y y Do not use volatile liquids such as insecticide spray near the unit. y y Wiping with strong pressure may damage the surface. y y Do not leave rubber or plastic products in contact with the unit for a long period of time. Maintaining the Unit The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service centre. Notes on Discs Handling Discs Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the centre to out. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.
Have a question about the LG BP120 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the LG BP120. Please make sure that you describe your difficulty with the LG BP120 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.