Krüger&Matz KM 1808 manual

View a manual of the Krüger&Matz KM 1808 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Krüger&Matz
  • Product: Hi-Fi system
  • Model/name: KM 1808
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Polish, Romanian

Table of Contents

Page: 0
RO
PL
NL
FR
EN
DE
BEDIENUNGSANLEITUNG
OWNER’S MANUAL
Mode d’emploi
Gebruiksaanwijzing
INSTRUKCJA OBSŁUGI
MANUAL DE UTILIZARE
Micro system with DVD, HDMI,
USB, BT, NFC, DAB+, FM
KM1808
Page: 26
27
Owner’s manual
EN
Before Use
Thank you for purchasing this system. Please read these operating instructions
before operating the unit. The operating instructions should be retained for future
reference.
For your safety
Before operating this system, check the
voltage of this system to see if it is identical
with the voltage of your local power supply.
When you disconnect the power cord,
always pull the plug, never the cable.
Protect the power cord from being walked
on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the device.
Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
To avoid electric shock, do not open the
cabinet. Refer all servicing to qualified
service personnel.
Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the
product.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
Don’t obstruct the ventilation openings of
the equipment with items such as newspa-
per, table-cloths,curtains, etc.. Overheating
will cause damage and shorten the life of
the equipment.
NEVER let anyone especially children
push anything into holes, slots or any
other opening in the case - this could
result in a fatal electrical shock;
Never hitting the product use the sharp
objects.
Laser Product
This product is equipped with low power
laser equipment. For your own safety do
not remove any covers or take the product
apart. Repair work must be carried out by
qualified personnel.
CLASS 1
LASER PRODUCT
Caution:
This product is equipped with low
power laser equipment inside, for
your safety, don’t open the laser ra-
diation protective equipment. Don’t
look at the laser radiation district
when the equipment is operating.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO
DRIPPING OR SPLASHING.
CAUTION:
TO REDUCE THIS RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER
(OR BACK), NO USER SERVICEABLE PARTS
INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Page: 27
28
Owner’s manual
EN
Hearing safety
Listen at a moderate volume.
* Sound can be deceiving. Over time your hearing “comfort level”adapts to higher
volumes of sound. So after prolonged listening, what sounds “normal”can actually
be loud and harmful to your hearing. To guard against this, set your volume to a
safe level before your hearing adapts and leave it there.
To establish a safe volume level:
* Set your volume control at a low setting.
* Slowly increase the sound until you can hear it comfortably and clearly, without
distortion.
Listen for reasonable periods of time:
* Prolonged exposure to sound, even at normally “safe”levels, can also cause
hearing lose.
* Be sure to use your equipment reasonably and take appropriate breaks.
1. Clean with soft, slightly damp cloth only.
2. Use only original accesories.
3. Unplug the device during lightning storms or when unused for long periods of
time.
4. Different types of batteries or new and used batteries are not to be mixed.
5. When inserting batteries, please note the correct polarity.
6. This appliance may be used by children who are above 8 years old and by persons
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised and guided by a person who is responsible for
their safety in a cautious manner, and all the safety precautions are understood
and followed. Children should not play with this device. Children should not
perform cleaning and servicing of the device unsupervised.
7. Fixed power cable may only be replaced in an authorized service point.
8. Do not move the unit during playback
9. To avoid danger of suffocation, keep the bag away from babies and children.
This bag is not a toy.
Page: 28
29
Owner’s manual
EN
PRODUCT DESCRIPTION
Page: 29
30
Owner’s manual
EN
1. Standby Button
2. Power indicator
3. Disc Tray
4. Next Button / Previous Button
5. Remote Sensor
6. Open/Close Button
7. Play/Pause Button
8. Holder
9. USB port
10.Select a play function
11.HDMI ARC output
12.Coaxial input
13. Display
14. Volume Control Knob
15. Optical input
16. Audio output sockets (L&R)
17. Video output socket
18. AUX Input Sockets (L&R)
19. Speaker Output Sockets (L&R)
20. DAB/FM Antenna Socket
21. AC Power Socket
22. NFC Sensor area
1. Standby Button
2. SOURCE (Select source)
3. PAIR (Play/pause/resume playback; Activate
the pairing function in Bluetooth mode and
disconnect the existing paired Bluetooth device)
4. REPEAT (Select repeat play modes) / SHUFFLE
(Select shuffle play mode) / A-B (Repeat a
specific section within a track/chapter)
5. TITLE (Access title menu)
6. SUBTITLE (Select a subtitle language during
video play)
7. SLEEP (Set the sleep timer) / TIMER (In
standby mode, press and hold to set the
alarm timer)
8. CLOCK (In standby mode, press and hold to
activate clock setup / Display current clock)
9. MENU (Return to upper-level menu / Enable/
disable the playback control menu for VCD)
10. PRESET UP/DOWN (Navigate up/down; Select
previous/next preset station; Rotate a picture)
11. STOP button (Press to stop playback; In FM
mode, press and hold this button to erase
radio stations memory)
12. Skip to previous/next title, chapter or track.
13. Numeric keypad (0~9)
14. GOTO (During disc play, specify a position to
start playback)
15. Open / close (disc compartment)
Remote control overview 1
2
3
7
9
11
12
13
14
15
16
17
18
19
20
21
23
24
25
26
27
28
29
10
8
6
22
4
5
16. SLOW (During video play, select a slow
backward/forward speed)
17. OSD (Display the information about the
currently playing disc)
18. AUDIO (For VCD: select stereo mono-left
or mono-right channel; For DVD video:
select an audio language)
19. ZOOM in / out
20. ANGLE (Select a camera angle to view
video play)
21. DIMMER (Adjust display brightness)
22. EQ (Select preset equaliser)
23. SETUP (Access or exist system setup menu)
24. Search backward/forward within a track/
disc; Navigate left/right; Tune radio
station; Rotate picture
25. ENTER (Confirm selection)
26. Mute / resume sound
27. VOL+/VOL- (Increase/decrease volume
level)
28. Play/pause/resume playback
29. PROG (Program sound tracks; Presets
radio stations; Press and hold to scan for
radio stations)
Page: 30
31
Owner’s manual
EN
Handling the Remote Control
• Remove the batteries if the remote control is not going to be used for an
extended period of time.
• To avoid possible failure, read the following instructions and handle the remote
control properly.
• Do not drop or cause impact to the remote control.
• Do not spill water or any liquid on the remote control.
• Do not place the remote control on a wet object.
• Do not place the remote control under the direct sunlight or near sources of
excessive heat.
• Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner
etc.) on the remote, as it may suffer damage.
Note:
Remove the battery from remote control handset when it is not to be used for a long
period. Otherwise it can be damaged due to leakage of battery.
Installation of batteries
1. Open the battery cover.
2. Insert 2 AAA batteries with correct polarity
(+/-) as indicated.
3. Close the battery cover.
Remote Control Operation
Range
Point the remote control to the unit
no more than 6 meters from the
remote control sensor and within 30°
horizontally and 30° vertically of the front of the unit. The
operating distance may vary according to the brightness of
the room.
Note:
• Make sure that there is no obstacle between the infrared
remote sensor of the unit and remote control, as the
remote controllable range may decrease
• Do not expose the infrared remote sensor to direct sunlight
or other strong light, such as inverter fluorescent light.
Max. 6 m
30° 30°
Page: 31
32
Owner’s manual
EN
CONNECTIONS
Caution: Make all connections before plugging the unit into the AC Power outlet.
Connecting the FM/DAB Antenna
Connect the supplied FM/DAB Antenna to the ANT socket on the rear of the unit by
turning the Antenna screw cap (as indicated).
Note: Do not overtighten, this could damage the Antenna.
Caution: To avoid noise, keep Antenna away from the unit, the connecting cable
and the AC power cable.
Connecting the Speakers
Connect the speaker cords between the terminals as shown below.
Connect the cable with a sliver head to the (-) terminals and cable with a gold head
to the (+) terminals.
Note:
• For optimal sound, use the supplied speakers only.
• Connect only speakers with impedance that is the same or higher than the
supplied speakers
How to connect:
1. Turn the terminal cap counterclockwise to loosen it. The speaker terminal caps
cannot be fully removed from the base.
2. Insert the wire into the terminal fully.
3. Turn the terminal cap clockwise
to securely connect it.
Page: 32
33
Owner’s manual
EN
Connecting to the composite video socket
• Connect the composite video (YELLOW) cable to the VIDEO socket on this unit
and the video input socket on the TV.
• Then Connect audio cables (RED/WHITE) to the AUDIO OUT R / L sockets on this
unit and the audio input sockets on TV.
AUDIO IN
R L
VIDEO
Connecting HDMI
Use a HDMI cable (not included) to connect the HDMI ARC socket on the unit and
to the HDMI ARC socket on the TV.
Tips:
• Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and ARC must
be set to On.
OPTICAL Socket
OPTICAL
Connect an OPTICAL cable (not included) to the TV’s OPTICAL OUT socket and the
OPTICAL socket on the unit.
Page: 33
34
Owner’s manual
EN
COAXIAL Socket
Use the COAXIAL (not included) cable to connect the TV's COAXIAL OUT socket and
COAXIAL socket on the unit.
AUX Socket
Use a RCA to RCA audio cable (not included) to connect the TV’s audio output
sockets to the AUX (R L) socket on the unit.
L
R
Use a RCA to 3.5mm audio cable (included) to connect the audio player’s
headphone socket to the AUX (R L) socket on the unit.
Page: 34
35
Owner’s manual
EN
GENERAL OPERATION
Powering ON/OFF
When you insert the AC power cable into a wall outlet, the unit will be in standby mode.
• Press the STANDBY button to switch the unit on.
• Press the STANDBY button to switch the unit back to standby mode.
Disconnect the mains plug from the mains socket if you want to switch the unit off
completely.
If there is no signal input under the DISC, USB, BT (Bluetooth), ARC, COAXIAL,
OPTICAL or AUX mode, the unit will automatically switch off within 15 minutes.
Connecting the AC Power Cable
Insert the AC Power cable into a wall outlet, then your unit is ready to use.
Caution:
• Be sure to unplug the power plug from the outlet when the unit is not in use for
an extended period of time.
• Ensure that the power supply voltage corresponds to the voltage printed on the
back or the underside of the unit.
Setting the clock
Synchronization of the Clock
Note: by default, time is synchronized with RDS.
1. When in STANDBY mode, press and hold the MENU button on the remote
control to synchronise the clock.
2. Press the / buttons on the remote to switch the clock synchronization modes:
• RDS Only synchronize with the RDS radio station.
• OFF Turn off the clock synchronization function, only adjust the clock
manually.
3. Then press the ENTER button on the remote control to confirm.
Page: 35
36
Owner’s manual
EN
Manual setting of the clock
1. In STANDBY mode, press and hold CLOCK until “CLOCK SET” scrolls on the
display.
2. Press the / buttons on the remote control to adjust the hour digits while
flashing, then press the CLOCK or ENTER button on the remote control to
confirm, then the minute digits will flash.
3. Press the / buttons on the remote control to adjust the minute digits while
flashing, then press the CLOCK or ENTER button on the remote control to
confirm.
Note:
• Press the button on the unit or the button on the remote control to select
12/24 hour format.
• Each activated state will be cleared if any buttons are not pressed within 15
seconds.
Select the Correct TV System
Change this setting if the video is not displayed correctly. By default, this setting
matches the most common setting for TVs.
1. Press the SETUP button to access or exit system setup menu.
Press the / , / buttons and press the ENTER button to confirm selection.
2. Select [ video ] -> [TV SYSTEM].
3. Select setting:
• [PAL] - For TV with PAL color system.
• [AUTO] - For TV that is compatible with both PAL and NTSC.
• [NTSC] - For TV with NTSC color system.
Select Modes
Press the button on the unit or the SOURCE button on the remote control
repeatedly to select DISC, USB, OPTICAL, FM, DAB, Bluetooth, AUX, COAXIAL, ARC
mode. The selected mode will show on the display.
Adjusting the Volume
To increase or decrease the volume, rotate the VOLUME control knob on the unit or
press the VOL+/VOL- buttons on the remote control.
Mute sound
During play, press the MUTE button to mute. Press the MUTE button again or
rotate the volume knob to unmute.
Page: 36
37
Owner’s manual
EN
Presetting Equalizer
You can adjust the sound reproduced simply by choosing from 5 preset equalizers.
Press the EQ button repeatedly to scroll through the following options:
FLAT > POP > CLASSIC > ROCK > JAZZ (looped)
Changing the Front Panel Darkness
To dim or brighten the display, press the DIMMER button repeatedly on the remote
control to the desired brightness.
Play for External Audio Devices
1. Ensure that the unit is connected to the TV or audio device.
2. While in ON mode, press the button on the unit or the SOURCE button on
the remote control repeatedly to select the OPTICAL, AUX, COAXIAL / HDMI ARC
mode.
3. Operate your audio device directly for playback features.
4. Press the VOL +/– buttons to adjust the volume to your desired level.
In the OPTICAL, AUX, COAXIAL / ARC mode, if there is no sound output,
ensure the audio setting of the input source is set to PCM mode.
DAB radio operation
Caution:
• Make sure that you have correctly connected and fully extended the antenna.
• You can program a maximum of 20 DAB radio stations.
To listen to the tuned stations press the / buttons. Each time you press the /
buttons, you will skip to the previous or next stored station (including primary and
secondary station). The unit will display the station name.
1. Press the button on the unit or the SOURCE button on the remote control
repeatedly to select DAB radio.
2. Press the MENU button on the remote control to display the DAB menu. Press the /
buttons to select Full scan. Press the ENTER button to confirm.
Auto Scan
The auto scan will search for all DAB Band III channels. After the scan has finished,
the first alphanumerically found station will be automatically selected.
1. Press the MENU button on the remote control to enter the DAB menu. Then
press the / buttons to select the “FULL SCAN”. Press the button on
the remote control to confirm. The display will show “SCAN…”that indicates the
progress of the scan and the amount of stations that have been found so far.
• Alternatively directly press the SCAN button on the remote control to
Page: 37
38
Owner’s manual
EN
perform a full scan.
2. Once the scan has finished, the unit will display the total number of stations
have been found and a list of the found stations. All the stations that have been
found will be stored automatically.
To explore the found stations, press the / buttons to the selected station.
• Full auto scan will not replace the DAB stations in memory. If you want to
remove all the previously scanned stations, system reset is required.
Presetting Stations Manually
You can store up to 20 of your favourite DAB stations to the memory. This will enable
you to access your favourite stations quickly and easily.
1. To store a preset, you must first be listening to the station that you would like
to save.
2. Press the PROG button on the remote control. The display will show “## Empty”,
and the preset number will flash.
3. Press the / buttons on the remote control to select your desired station
preset number.
4. Press the PROG button to confirm your station, the display will show “STORE”.
Recalling a Preset Station
1. Once you have saved a station to one of the preset buttons, you can recall it by
pressing the / buttons on the remote control to select your desired preset
number.
2. Preset number and station name will show on the display to indicate the preset
station you are listening to.
• The stored stations will be saved into the memory and power off will not
erase it. Storing a new station in a preset location will erase the previously
stored station in that location.
DAB Information Display
You can view the DAB service information in the following modes. Depending on the
DAB radio station you are tuning to, some information modes may be unavailable.
Repeatedly press the INFO button on the remote control to view the following
information.
• DLS
Dynamic label segment is a scrolling message that the broadcaster may include
with their transmissions. The message usually includes information, such as
programme details etc.
Note: DAB – unlike normal radio, groups together several radio stations and
transmits them on one frequency.
• Singal strength
The display will show a slide bar to indicate the signal strength, the stronger the
signal, the longer the bar will be from left to right.
• Programme type
• Ensemble name
A multiplex is a collection of radio stations that are bundled and transmitted
Page: 38
39
Owner’s manual
EN
on one frequency. There are national and local multiplexes. Local ones contain
stations that are specific to that area.
• Channel number
• Frequency
• Error in signal
A number showing the error rate. If the number is 0, it means the signal
received is error free and the signal strength is strong. If the error rate is high, it
is recommended to reorient the radio aerial or reposition the unit.
• Audio mode
Stereo/Mono
• Clock (if not available, the display will show incorrect time)
• Date (if not available, the display will show incorrect date)
FM RADIO OPERATION
Note:
• Before operating the radio, please check that the antenna is correctly connected
and adjusted for length and direction.
• You can program a maximum of 20 FM radio stations
Auto Scan and Save Preset Station
1.Press the button on the unit or the SOURCE button on the remote control
repeatedly to select TUNER mode.
2.Press and hold the PROG button on the remote control to activate automatic
programming. All available stations are programmed in the order of waveband
reception strength.
• The first programmed radio station is played automatically.
• Tune to a Preset Radio Station
• Press the PRESET / buttons to select a preset number that you want.
Tuning in a Station
• Tune in radio stations automatically
• Press and hold the , buttons on the unit, the frequency changes down
or up automatically until a station is found.
• The search may not stop at a station with a very weak signal.
• Tune in radio stations manually
• Press the , buttons repeatedly until you find the station you want.
• If reception is still poor, try to adjust the position of the aerial or try to move
the radio to another location.
Presetting Stations Manually
You can preset up to 20 FM stations.
1.Tune in the desired station, then press the PROG button.
Page: 39
40
Owner’s manual
EN
2.Press the / or number (0~9) buttons to select the preset number.
3.Press the PROG button to store the station.
4.Repeat above steps 1 to 3 for each station you want to store in memory with a
preset number.
RDS RECEPTION
FM Display Modes
Every time you press the OSD button, the display will cycle through the following
display modes: Station Name, Programme Type, Radio Text, Frequency , CLOCK
INFO.
Note:
• RDS information will be displayed only if available
• When automatic programming is used, RDS stations are
• programmed first.
Disc Operation
1. While in ON mode, press the button on the unit or the SOURCE button on
the remote control repeatedly to select DISC mode.
2.Press the button to open the disc door and place the disc on the disc tray (with
the printed side up).
3.Press the button to close the disc door, the unit will read the disc and play it
automatically.
Note: If the playback does not start automatically, select a title/chapter/track and
then press the button.
USB operation
1.Insert the USB device’s USB plug into the USB socket.
2.Press the USB button on remote control or button on the unit to select the
USB source.
3.Playback starts automatically. If the playback does not start automatically, select
a title/chapter/track and then press the button
Page: 40
41
Owner’s manual
EN
USB Storage Device Data Protection
• Always insert the USB device in the correct direction. Failure to do so may result
in damage to the USB device and this unit.
• Do not remove the USB device while it is being accessed.
• Electrical interference and electrostatic discharges may cause the USB device to
malfunction and suffer damage, resulting in data loss.
It is strongly recommended that any important data is backed up on a PC to protect
against corruption, data loss or device malfunction. Please note that our company
shall not accept any liability for damage or loss of stored data.
Note: USB connection may not compatible with all hard drive models.
Play Control
• To stop play, press the button on the remote control.
• To pause or resume play, press the button on the unit or the , button on
the remote control.
• To skip to the previous/next track, press the / buttons on the unit or /
buttons on the remote control.
• Press and hold the , buttons on the remote control to perform fast
forward/ reverse playback. Press the button to resume normal playback.
• Press the OSD button on the remote control to display the current play
information.
Slow backward/forward play
1. During video play, press SLOW button to select a slow backward speed.
• The sound is muted.
2. To resume play at normal speed, press the or button.
Random Playback
During play, press the SHUFFLE button, unit will randomly play the song.
Select Repeat Play Options
During play, press the REPEAT button repeatedly to select a repeat option play
Page: 41
42
Owner’s manual
EN
mode. The selected mode will show on the display:
RPT ONE - Repeat current track.
RPT ALL - Repeat all tracks.
RPT OFF - Repeat turned off.
Repeat A-B (DVD/VCD/CD/MP3/WMA)
1. During music or video play, press the A-B button at the start point.
2. Press the A-B button at the end point.
• The selected section starts to play repeatedly.
• To cancel repeat play, press the A-B button again.
Note: The section A and B can be set only within the same track/title.
Select an Audio Language
During disc play, press the AUDIO button to select an audio language on video DVDs.
• The language options appear. If the selected audio channels is unavailable, the
default audio channel is used.
• For some DVDs, the language can only be changed from the disc menu. Press
the MENU button to access that menu.
Display Menu
In DVD play mode, press the TITLE button to go back to the title menu during PBC
playback.
Select a Subtitle Language
• During playing, press the SUBTITLE button to select a subtitle language on DVDs.
• For some DVDs, the language can only be changed from the disc menu. Press
the MENU button to access that menu.
Select a Camera Angle
During play, press ANGLE button repeatedly to select a camera angle.
• This feature is only available for DVDs recorded with multiple camera angles.
Zoom in/out image
During video/picture play, press the ZOOM button to zoom in/out the image.
• When the image is zoomed in, press , , , buttons to go across the image.
Use the Disc Menu
When you load a DVD/(S)VCD disc, a menu may be displayed on the TV screen.
• To access or exit the menu:
Press the MENU button.
• For VCD with PlayBack Control (PBC) feature (version 2.0 only):
The PBC feature allows you to play VCD interactively according to the menu screen.
Page: 42
43
Owner’s manual
EN
During playing, press the MENU button to enable/disable PBC.
• When PBC is enabled, the menu screen is displayed.
• When PBC is disabled, normal play is resumed.
Search by Time or Chapter/Track Number
1. During the DVD/VCD playback, press the GOTO button to access quick menu:
• For the Track/Title/Chapter field, enter the track/title/chapter number.
• For the Disc time/Track time/Title time/ Chapter time, enter the play position
in hours, minutes and seconds.
2. Use numerical (0~9) buttons to input title/chapter/ track number and disc/track time.
3. Press ENTER button to confirm a selection. Play starts automatically at your
selected point.
Programme Play
You can programme up to 20 tracks to play in any desired order. The player must be
in STOP mode only with a Disc inserted.
1.Insert a disc and press the Stop button when it starts playing.
2.Press the PROG button.
3.Press the number buttons (0-9) or / buttons on the remote control to select
the desired track number.
4.Press the PROG button to confirm the track number to be stored.
5.Repeat steps 3-4 to select and store all desired tracks.
6.Press the button to start programme play.
7.Press the button twice or open the disc compartment to clear programme.
The display shows "PRG CLR".
Play from Bluetooth device
Pairing bluetooth-enabled devices
To connect your Bluetooth device to the unit, you need to pair the device to the unit.
Pairing needs to be done only once.
1.Press the button on the unit or the SOURCE button on the remote control
repeatedly to select BT (Bluetooth) mode. “NO BT” will show on the display if the
unit is not paired to any Bluetooth device.
2.The system has entered pairing mode.
• press the "PAIR" button on the remote control or press and hold the button
on the unit to be searchable. The display will show “PAIR”.
3.Turn on the Bluetooth function on your device.
4.Search for other Bluetooth device with your device.
5.Select “KM1808” in the pairing list.
6.Enter default password “0000” if necessary.
7.Start music play on your Bluetooth device, you can use this unit’s remote to
control the function to your Bluetooth device.
Page: 43
44
Owner’s manual
EN
Note:
• The device will also be disconnected when the device is moved beyond the
operation range.
• If you want to reconnect the device to the unit, place it within the operational range.
• The operational range between this unit and a Bluetooth device is up to 8 meters.
• Compatibility with all Bluetooth devices is not guaranteed.
• AnyobstaclebetweenthisunitandaBluetoothdevicecanreducetheoperationalrange.
• Keep this unit away from any other electronic device that may cause interference
• If a connection exist, press the "PAIR" button on the remote control or press and
hold the button on the unit to re-activate the pairing mode, the connection
will be interrupted.
• If no other Bluetooth device pairs with this player within two minutes, the player
will recover its previous connection.
• When connected to an external device, the display shows "BT".
• If the connected Bluetooth device supports Advanced Audio Distribution Profile
(A2DP), you can listen to the music stored on the device through the player.
• If the external device supports Audio Video Remote Control Profile (AVRCP), you
can use the player’s remote control to play music stored on the device.
Set sleep timer
This unit can switch to standby mode automatically after a set period.
When the unit is turned on, press SLEEP button repeatedly to select a preset period
(in minutes):
120 > 90 > 60 > 45 > 30 > 15 > 00
• Press the SLEEP button to view the remaing time before switch off.
• To deactivate the sleep timer, press SLEEP button repeatedly until [SLEEP 00] is
displayed.
SET THE ALARM TIMER
This unit can be used as an alarm clock. You can select DISC, USB, DAB or TUNER
as alarm source.
1.In standby mode, press and hold the TIMER button until [TIMER SET] scrolls on
the display. Then the hour digits flash.
2.Press / button on the remote control to adjust the hour digits, and then press
the TIMER button on the remote control to confirm, the minute digits will flash
on the display.
3.Press the / buttons on the remote control to adjust the minute digits, and
then press the TIMER button on the remote control to confirm.
4.Press the / buttons on the remote control to select:
• TUNER (to wake to your selected FM Radio Station)
• DAB (to wake to your selected DAB Radio Station)
Page: 44
45
Owner’s manual
EN
• DISC (to wake to your Disc music)
• USB (to wake to your USB music)
Press the TIMER button on the remote control to confirm, the display will show the
volume level.
5.Press the / buttons on the remote control to adjust the volume, and then
press the TIMER/SLEEP button on the remote control to confirm. “TMR ON / TMR
OFF” will flash on the display.
6.Press the / buttons to select “TMR ON” or “TMR OFF” to enable the timer or to
disable the time, and then press the TIMER/SLEEP button on the remote control
to confirm.
Press the TIMER/SLEEP button on the remote control to view the alarm settings or
activate the alarm.
Note:
• Each enabled state will be cleared if a button is not pressed within 15 seconds.
• When the alarm rings, press the button on the remote control or on the unit.
The alarm stops but the alarm settings remain.
SETTING ADJUSTMENTS
Most settings and adjustments are required to be set when you first use the unit.
Settings adjustment is available after connecting this device to TV set via HDMI cable.
Press the SETUP button to access or exit system setup menu.
Press the / , / buttons and press the ENTER button confirm selection
TV SYSTEM AUTO: For TV that is compatible with both PAL and NTSC.
NTSC: For TV with NTSC color system.
PAL: For TV with PAL color system.
POWER
RESUME
ON: Select this to make last memory function available for DISC.
OFF: Select this to make last memory function invalid.
POWER RESUME
SCREEN SAVER
HD Resolution
Aspect Ratio
PASSWORD
RATING
DEFAULT
Osd Language
Audio
Subtitle
DVD Menu
HDMI CEC
HDMI AUDIO
Page: 45
46
Owner’s manual
EN
SCREEN SAVER ON: The screen saver starts up if nothing is played back and no
operations are performed for 4 minutes.
OFF: The screen saver does not start up.
HD Resolution The resolution options include AUTO, 480i/576i, 480p/576p,720p, 1080i,
1080p.
Note: If no display appears on the TV screen due to unsupported
resolution, reconnect any available interlace video output to your
isplay and re-adjust the resolution settings to 480p/576p.
Aspect Ratio To avoid distortion on older televisions, you may need to change the
way in which the image is displayed. Televisions use a 4:3 aspect ratio;
high-definition televisions use 16:9 aspect ratio (as do movies).
• Some discs do not allow the aspect ratio to be changed and you will
therefore have to change the aspect ratio on the TV.
[4:3PS]: This mode is used with 4:3 televisions. 4:3 images are displayed
normally. When showing 16:9 programmes, the full height of the
screen is displayed, and the left and right part of the image are cut
off.
[4:3LB]: This mode is used with 4:3 televisions. 4:3 images are displayed
normally. 16:9 images are visible at their full width, but there are
blank area at the top and bottom of the screen.
[16:9]: Use with a 16:9 wide television.
• Some wide-screen discs that do not permit the Pan Scan mode
playback are automatically played in Letter Box mode.
• Depending on the DVD, 4:3 Letter Box may be selected
automatically instead of 4:3 Pan Scan and vice versa.
• If 16:9 (Wide) is selected and a normal TV is connected, 16:9
content will appear distorted during playback (objects look thin).
PASSWORD You can set a new password for parental control.
RATING Playback of some DVD discs can be limited depending on the age of the
users. The parental control system allows the playback limitation level to
be set by the parent.
• The lower the level, the stricter the limitation.
• If the rating of the loaded DVD disc is higher than the level you set,
the system will require a password. Enter your password and press
the ENTER button to start playback.
DEFAULT All the items in the Setup menu (except for the password and parental
control) will be reset to the default settings.
OSD Language Select the desired language for on screen menus of the unit.
Audio
Subtitle
DVD Menu
You can select a preferred language for audio, subtitle and disc menu.
• When you select a preferred language that is not recorded on the
DVD, one of the recorded languages is automatically selected.
• You can override the Audio setting in the Setup menu by pressing the
AUDIO button on the remote control unit while a DVD disc is playing.
• You can override the Subtitle setting in the Setup menu by pressing the
SUBTITLE button on the remote control while a DVD disc is playing.
Page: 46
47
Owner’s manual
EN
HDMI CEC You can use one single remote control to control all HDMI CEC devices
that connected via HDMIconnection.
ON: Enable HDMI-CEC feature. OFF: Disable HDMI-CEC feature.
HDMI AUDIO AUTO: Detect and select the best supported audio format automatically.
PCM: Multi-channel audio format will be down-mixed to two channel
sound.
• To keep the disc clean, please don’t touch the disc’s surface when you
are holding it. You should hold the edge.
• If the disc is dirty, it will affect the sound quality. Please use the clean and
soft cloth to wipe the disc from inside to outside. Don’t wipe the disc in
circular motion.
• Don’t stick paper on the disc.
• After you have finished with the disc, please place it back in its original
case. To avoid warping or damage, do not stack discs.
• Don’t play the disc which has flaw or deformation, in case of damaging this
player.
• Clean your discs using only a soft dry cloth. Do not use any chemicals such
as benzine, thinner, antistatic or record sprays as these can damage the disc
surface.
Protect the Disc
Page: 47
48
Owner’s manual
EN
If you are having a problem with your system, check this list for a possible solution
before calling for service.
If you can not solve the problem from the hints give here, or the system has been
physically damaged, call a qualified person, such as your dealer, for service.
Troubleshooting
No power No disc detected
• Ensure that the AC adaptor plug of
the unit is connected properly.
• Ensure that there is power at the AC
outlet.
• Insert a disc.
• Check if the disc is inserted with the
print side facing inward.
• Wait until the moisture condensation
at the lens has cleared.
• Replace or clean the disc.
• Use a finalized Disc or correct format
disc.
Poor radio reception
• Increase the distance between the
unit and your TV or VCR.
• Fully extend and adjust the FM
antenna.
USB device not supported
The USB device is incompatible with
the unit. Try another one.
No sound
Adjust the volume.
Cannot display some file in USB
device
• The number of folders or files in the
USB device has exceeded a certain
limit. This phenomenon is not a
malfunction.
• The formats of these files are not
supported.
Timer does not work
• Set the clock correctly.
• Switch on the timer.
Remote control does not
work
• Before pressing any function button,
first select the correct source with
the remote control instead of the
main unit.
• Reduce the distance between the
remote control and the unit.
• Insert the battery with its polarities
(+/– signs) aligned as indicated.
• Replace the batteries.
• Aim the remote control directly at
the sensor on the front of the unit.
Page: 48
49
Owner’s manual
EN
DVD player
Bluetooth 3.0
NFC
FM radio
DAB+ digital radio
Max. output power: 2x 50 W
Frequency response: 45 Hz – 20 kHz
Impedance: 6 Ω
I/O:
HDMI ARC output
USB port
Coaxial input
Optical input
AUX input (2x RCA)
Audio output (2x RCA)
video output (1x RCA)
Remote Control
Power consumption: 40 W
Power consumption in standby mode: < 0,5 W
Power supply: 220-240 V; 50/60 Hz
Specifications
English
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or Its literature, indicates that It should not be disposed with other
household wastes at the end of its working life. To prevent possible harm lo the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government office, for details of where and
how they can take this item for environmentally safe recycling. Business users should contact their supplier
and check the terms and conditions of the purchase contract This product should not be mixed with other
commercial wastes for disposal.
Made in China for LECHPOL, Miętne, 1 Garwolińska Street, 08-400 Garwolin.
Specifications are subject to change without prior notice.
“The Lechpol company declares that product KM1808 is consistent with the essential requirements and other
relevant provisions of directive 2014/53/UE. The proper declaration for download from www.lechpol.eu”
LEARN MORE
For more information on this product, go to www.krugermatz.com.
Visit www.krugermatz.com website for more products and accessories.
In case of any doubts or questions reach out to our Frequently Asked Questions section.

Question & answers

There are no questions about the Krüger&Matz KM 1808 yet.

Ask a question about the Krüger&Matz KM 1808

Have a question about the Krüger&Matz KM 1808 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Krüger&Matz KM 1808. Please make sure that you describe your difficulty with the Krüger&Matz KM 1808 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.