JVC UX-S10 manual

View a manual of the JVC UX-S10 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: JVC
  • Product: Hi-Fi system
  • Model/name: UX-S10
  • Filetype: PDF
  • Available languages: English, Dutch, German, French, Italian

Table of Contents

Page: 0
LVT1563-001A
[B]
INSTRUCTIONS
MICRO COMPONENT SYSTEM
UX-S10—Consists of CA-UXS10 and SP-UXS10
UX-S10[B]_C_01cover_f.p65 06.3.10, 5:17 PM
1
Page: 1
Warnings, Cautions and Others
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appro-
priate safety approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical approved
type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the fuse
and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow
the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue : Neutral
Brown : Live
As these colours may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
CAUTION— STANDBY/ON button!
Disconnect the mains plug to shut the power off completely (all lamps
and indications go off). When installing the apparatus, ensure that the
plug is easily accessible. The STANDBY/ON button in any position
does not disconnect the mains line.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to qualified
service personnel.
3. CAUTION: Visible and invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Front view
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Side view
G-1
UX-S10
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEI.
GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT
IST. NICHT DEM STRAHL AUSSETZEN!
VARNING - OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.
ADVARSEL -USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
CA-UXS10
10 cm
15 cm
1 cm
15 cm
15 cm 1 cm
15 cm
15 cm
UX-S10[B]_C_02safety_f.p65 06.3.10, 5:17 PM
1
Page: 2
G-2
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment)
are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or
changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off,
withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation
or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is
illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result
in a fatal electrical shock.;
— NEVER guess or take chances with electrical equipment of any kind
— it is better to be safe than sorry!
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be disposed as general household
waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with
your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential
negative effects on the environment and human health which could otherwise be caused by inappropriate waste
handling of this product. For more information about collection point and recycling of this product, please contact
your local municipal office, your household waste disposal service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about
the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other
rules in your country for the treatment of old electrical and electronic equipment.
Attention:
This symbol is only
valid in the European
Union.
UX-S10[B]_C_02safety_f.p65 06.3.10, 5:17 PM
2
Page: 3
1
Power sources
• When unplugging the unit from the wall outlet, always pull
on the plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lenses inside the unit in the
following cases:
• After starting to heat the room.
• In a damp room.
• If the unit is brought directly from a cold to a warm place.
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, then plug it in again.
Others
• Should any metallic object or liquid fall into the unit,
unplug the AC power cord and consult your dealer before
operating any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
About This Manual
This manual is organized as follows:
• This manual mainly explains operations using the
buttons on the remote control.
You can use the buttons both on the remote control and
on the unit for the same operations if they have the
same or similar names (or marks), unless mentioned
otherwise.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated for
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Basic and Common Operations”
on pages 8 and 9.
• The following symbols are used in this manual:
Gives you warning and caution to prevent
damage or risk of fire/electric shock.
In addition, we put information here about
conditions which will prevent getting the best
possible performance from the unit.
Gives you information and hints you need to
know.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
• Install the unit in a location with adequate ventilation to
prevent internal heat buildup.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
UX-S10[B]_C_03name_f.p65 06.3.10, 5:17 PM
1
Page: 4
2
Contents
Location of the Buttons and Controls ............................. 3
Main unit ................................................................................... 3
Remote Control ......................................................................... 5
Getting Started .................................................................. 6
Unpacking ................................................................................. 6
Putting the Batteries into the Remote Control .......................... 6
Connections ............................................................................... 6
Basic and Common Operations ....................................... 8
Setting the Clock ....................................................................... 8
Turning On the Power ............................................................... 8
Selecting the Source .................................................................. 9
Adjusting the Volume ................................................................ 9
Selecting the Sound Modes ....................................................... 9
Reinforcing the Bass Sound ...................................................... 9
Listening to FM and AM (MW) Broadcasts ................. 10
Tuning in to a Station .............................................................. 10
Presetting Stations ................................................................... 11
Tuning in to a Preset Station ................................................... 11
Receiving FM Stations with Radio Data System .......... 12
Changing the Radio Data System Information........................ 12
Searching for Programs by PTY Codes (PTY Search) ........... 12
Playing Back Discs .......................................................... 14
Playing Back the Entire Disc—Normal Play .......................... 14
Basic Disc Operations ............................................................. 15
Programing the Track Playing Order—Program Play............. 15
Playing at Random—Random Play......................................... 16
Repeating Tracks —Repeat Play ............................................. 16
Displaying various information ............................................... 16
Playing Back Tapes.......................................................... 17
Playing Back a Tape ................................................................ 17
Recording ......................................................................... 18
Recording from the Radio ....................................................... 18
Recording Discs—Disc Synchronized Recording .................. 19
Using the Timers.............................................................. 20
Using the Daily Timer ............................................................. 20
Using the Sleep Timer ............................................................. 21
Maintenance..................................................................... 22
Troubleshooting ............................................................... 23
Specifications ................................................................... 24
UX-S10[B]_C_03name_f.p65 06.3.10, 5:17 PM
2
Page: 5
3
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Main Unit
TIMER ON/OFF
PHONES
SOUND
/BASS
BAND
OPEN
MULTI
CONTROL
CD
CONTROL
TAPE TUNER CD
1
2
3
4
5
6
7
8
STANDBY/ON
OPEN
VOLUME
CD SYNCHRO RECORDING
MICRO COMPONENT SYSTEM UX-S10
STANDBY
9
p
q
w
e
r
t
y
Top view
Front view
Inside the front cover
UX-S10[B]_C_03name_f.p65 06.3.10, 5:17 PM
3
Page: 6
4
ON OFF
1ALL
MP3 PRGM RAND TOTAL REMAIN
MHz
kHz
SYNC
SLEEP ST MONO SOUND BASS
GR.
1 2 3 4 5 6
t
e
w
p
9 q r
8
7
Display window on the front panel
Display window
1 (timer) indicator
2 ON/OFF (timer on-time/off-time) indicators
3 SLEEP indicator
4 FM mode indicators
• ST (stereo), MONO
5 SOUND indicator
6 BASS indicator
7 SYNC (synchro) indicator
8 Main display
• Shows the source name and other information.
9 MP3 indicator
p (group/folder) indicator
q Repeat indicators
• , 1, ALL, GR.
w PRGM (program) indicator
e RAND (random) indicator
r Time indicators
• TOTAL, REMAIN
t Frequency indicators
• MHz, kHz
Continued
See pages in parentheses for details.
Main unit
1 Disc cover (14)
2 PHONES jack (9)
3 TIMER ON/OFF button (20)
4 SOUND/BASS button (9)
5 0 OPEN (disc cover open) (14, 15)
6 Source buttons
• TAPE, TUNER/BAND, CD
Pressing one of these buttons also turns on the unit.
7 CD CONTROL buttons (14, 15)
• #¥8, 7
8 MULTI CONTROL buttons
• ¡¥¢, 4¥1
9 Display window
p STANDBY/ON button (8, 20)
q Standby lamp (8)
w Cassette holder (17)
e VOLUME + / – buttons (9)
r Remote sensor (5)
t Front cover (17)
y Tape operation buttons (17 – 19)
• ‡ (recording), # (play), ! (fast backward),
⁄ (fast forward), &/) (stop/cassette holder open),
* (pause)
To open the front cover
UX-S10[B]_C_03name_f.p65 06.3.10, 5:17 PM
4
Page: 7
5
SET
RANDOM SLEEP
REPEAT/
PTY SEARCH
STANDBY/ON
ON/OFF
REMAIN/
PS/PTY/RT
BEAT CUT
DISPLAY/
CLOCK SET
MUTING
SOUND/
BASS
CD
TAPE CD
VOLUME
TUNER/
BAND
FM MODE
PROGRAM
REMOTE CONTROL
TIMER
1
2
3
4
5
6
7
8
u
y
t
r
e
w
q
p
9
Remote Control
See pages in parentheses for details.
STANDBY/ON
STANDBY
VOLUME
CD SYNCHRO RECORDING
MICRO COMPONENT SYSTEM
When using the remote control, point it at the
remote sensor on the front panel.
1 TIMER SET button (20)
2 REPEAT/PTY SEARCH button (12, 16)
3 RANDOM button (16)
4 REMAIN/PS/PTY/RT button (12, 16)
5 BEAT CUT button (10, 18)
6 DISPLAY/CLOCK SET button (8)
7 MUTING button (9)
8 SOUND/BASS button (9)
9 STANDBY/ON button (8, 20)
p TIMER ON/OFF button (20, 21)
q SLEEP button (21)
w PROGRAM button (11, 15, 16, 20)
e FM MODE button (10)
r Source buttons
• TAPE, TUNER/BAND, CD
Pressing one of these buttons also turns on the unit.
t CD 3/8 button (14, 15)
y Multi control buttons
• ,
• 4, 7, ¢
u VOLUME + / – buttons (9)
UX-S10[B]_C_03name_f.p65 06.3.10, 5:17 PM
5
Page: 8
6
Getting Started
Unpacking
After unpacking, check to be sure that you have all the
following items.
The number in parentheses indicates the quantity of each
piece supplied.
• FM antenna (1)
• AM (MW) loop antenna (1)
• Remote control (1)
• Batteries (2)
If any item is missing, consult your dealer immediately.
Putting the Batteries into the Remote Control
Insert the batteries—R03(UM-4)/AAA(24F)—into the
remote control by matching the polarity (+ and –) on the
batteries with the + and – marking on the battery
compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
Continued
• DO NOT use an old battery together with a new
one.
• DO NOT use different types of batteries together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time.
Otherwise, the remote control will be damaged
from battery leakage.
Connections
To connect speakers
You can connect the speakers using the speaker cords.
1 Hold the clamp of the speaker terminal.
2 Insert the end of the speaker cord into the
terminal.
Match the polarity of the speaker terminals: red (ª) to
red (ª) and black (·) to black (·).
3 Release your finger from the clamp.
IMPORTANT:
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the unit.
• DO NOT connect more than one speaker to one
speaker terminal.
SPEAKER
IMPEDANCE
4-16 Ω
1 2,3
L
R
1
2
3
R03(UM-4)/
AAA(24F)
Black
Red
Black
Red
Speaker
cord
Speaker
cord
Left speaker
Right speaker
UX-S10[B]_C_04connect_f.p65 06.3.10, 5:17 PM
6
Page: 9
7
To connect AM (MW) and FM antennas
1 Attach the FM antenna to the FM COAXIAL
75 Ω terminal.
Fasten it up in the position which gives you the best
reception, then fix it on the wall, etc.
2 Connect the supplied AM (MW) loop
antenna to the AM LOOP terminal.
Place the antenna away from the unit and adjust its
position for the best reception.
For better reception of both FM and AM (MW)
• Make sure the antenna conductors do not touch any other
terminals or connecting cords.
• Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
AM (MW) loop antenna
(supplied)
IMPORTANT:
Be sure to check that all connections have been made
before plugging in the power cord.
FM antenna
NOW you are ready to plug in the unit.
2
1
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
To connect an outdoor FM antenna
Before connecting the antenna, disconnect the supplied FM
antenna.
Outdoor FM antenna
(not supplied)
A 75 Ω antenna with coaxial type connector
(IEC or DIN 45325) should be used.
Coaxial cable (not supplied)
AM
LOOP
FM 75 Ω
COAXIAL
AM
LOOP
FM 75 Ω
COAXIAL
UX-S10[B]_C_04connect_f.p65 06.3.10, 5:17 PM
7
Page: 10
8
Setting the Clock
Before operating the unit any further, first set the unit’s clock.
When you plug in the power cord, “0:00” starts flashing on
the display.
You can set the clock when the unit is either turned on or in
standby mode.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step 1.
On the remote control ONLY:
1 When the unit is in standby mode,
press and hold DISPLAY/CLOCK
SET until the hour indication starts
flashing.
• When the unit is on, press DISPLAY/CLOCK SET to
enter clock mode, then press and hold DISPLAY/
CLOCK SET.
2 Press 4 or ¢ to adjust
the hour, then press
DISPLAY/CLOCK SET.
• When you press and hold 4 or
¢, the hour indication changes
continuously.
The minute indication starts flashing.
3 Press 4 or ¢ to adjust
the minute, then press
DISPLAY/CLOCK SET.
• When you press and hold 4 or
¢, the minute indication changes
continuously.
“CLOCK OK” appears on the display for a
while and the built-in clock starts.
Basic and Common Operations
DISPLAY/
CLOCK SET
Turning On the Power
To turn on the unit, press STANDBY/ON.
The standby lamp on the unit goes off.
• When you press the source button—TAPE,
TUNER/BAND and CD, the unit automatically
turns on.
To turn off the unit (standby), press STANDBY/ON
again.
The standby lamp on the unit lights red.
• “0:00” flashes on the display until you set the built-in
clock. After setting the clock, the clock time will appear on
the display while the unit is on standby.
• A little power is always consumed even while the unit is in
standby mode.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “0:00” right away. If this happens, set the clock
again.
STANDBY/ON
• When you unplug the AC power cord or if a power failure
occurs
The clock is reset to “0:00” right away. If this happens, set the
clock again.
• The clock may gain or lose 1 to 2 minutes per month
If this happens, reset the clock.
To show the clock when the unit is turned on
On the remote control ONLY:
Press DISPLAY/CLOCK SET.
• Each time you press the button, the display
changes the clock indication and the normal
indication alternately.
To change the clock
Repeat steps 1 to 3 of the procedure “Setting the Clock.”
Continued
DISPLAY/
CLOCK SET
DISPLAY/
CLOCK SET
DISPLAY/
CLOCK SET
UX-S10[B]_C_05basic_f.p65 06.3.10, 5:17 PM
8
Page: 11
9
Selecting the Sound Modes
You can select one of the 4 sound modes.
• This function also affects the sound from headphones.
• This function only affects the playback sound, and does not
affect your recording.
To select the sound modes, press SOUND/BASS
repeatedly.
• Each time you press the button, the sound mode
changes as follows:
POP: More presence in the vocals and midrange.
CLASSIC: Enriched sound with fine treble and ample bass.
ROCK: Powerful sound emphasizing treble and bass.
JAZZ: Accented lower frequencies for jazz-type music.
FLAT: Equalizer effect is canceled.
When the sound mode is activated, the SOUND indicator
lights up on the display.
Reinforcing the Bass Sound
The richness and fullness of the bass sound is clearly
maintained regardless of how low you set the volume—Hyper
Bass Sound.
• This function also affects the sound from headphones.
• This function only affects the playback sound, and does not
affect your recording.
To get the effect, press and hold SOUND/BASS
until “HBS ON” appears and the BASS indicator
lights up on the display.
To cancel the effect, press and hold SOUND/BASS again
until “HBS OFF” appears and the BASS indicator goes off.
Adjusting the Volume
You can adjust the volume level only while the unit is turned
on. The volume level can be adjusted between “VOL MIN,”
“VOL 1” – “VOL 39,” and “VOL MAX.”
• The volume level has no effect on recording.
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
• When you press and hold either button, you
can change the volume level continuously.
To turn off the sound temporarily
On the remote control ONLY:
Press MUTING.
The volume level turn down and “MUTING”
starts flashing on the display.
To restore the sound, press MUTING again.
• Adjusting the volume level also cancels the muting.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume before
connecting or putting on the headphones.
DO NOT turn off (standby) the unit with the volume
set to an extremely high level; Otherwise, the
sudden blast of sound can damage your hearing,
speakers and/or headphones when you turn on the
unit or start playing any source.
REMEMBER you cannot adjust the volume level
while the unit is in standby mode.
SOUND/
BASS
VOLUME
SOUND/
BASS
MUTING
Selecting the Source
To select the source, press TAPE,
TUNER/BAND, or CD.
• When you select TAPE or CD as
the source, playback does not start
automatically.
To operate the tuner (FM or AM (MW)), see pages 10 – 13.
To operate the CD player, see pages 14 – 16.
To operate the tape deck, see page 17.
To record on a tape, see pages 18 and 19.
TAPE CD
TUNER/
BAND
JAZZ
FLAT
(Canceled)
CLASSIC
POP ROCK
(Initial)
UX-S10[B]_C_05basic_f.p65 06.3.10, 5:17 PM
9
Page: 12
10
Tuning in to a Station
1 Press TUNER/BAND to select either
“FM” or “AM.”
The unit automatically turns on and tunes in to
the previously received station—either FM or
AM (MW).
• Each time you press the button, the band alternates
between FM and AM (MW).
2 Press and hold ¢ or 4
(or ¡/¢ or 4/1 on
the unit) for more than 1
second.
• ¢ (¡/¢):
Increases the frequencies.
• 4 (4/1):
Decreases the frequencies.
The unit starts searching for stations and stops when a
station of sufficient signal strength is tuned in.
• If an FM program is broadcast in stereo, the ST (stereo)
indicator lights up on the display (only when the
reception is good).
To stop during searching, press ¢ or 4 (or ¡/¢ or
4/1 on the unit).
When you repeatedly press ¢ or 4 (or ¡/¢ or
4/1 on the unit)
The frequency changes step by step.
Listening to FM and AM (MW) Broadcasts
TUNER/
BAND
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE so that the MONO
indicator lights up on the display. Reception will
improve.
To restore the stereo effect, press FM MODE again so that
the MONO indicator goes off. In stereo mode, you can hear
stereo sound when a stereo program is broadcast.
To reduce the beat when listening to an AM (MW)
station—Beat Cut
On the remote control ONLY:
While recording an AM (MW) broadcast, beats
may be heard (which are never heard when
listening to the broadcast without recording it).
If this occurs, press BEAT CUT repeatedly, while
recording, until the beats are reduced.
• Each time you press the button, the display alternates
between “CUT–1” and “CUT–2.”
FM MODE
BEAT CUT
Continued
UX-S10[B]_C_06tuner_f.p65 06.3.10, 5:17 PM
10
Page: 13
11
Presetting Stations
You can preset 30 FM and 10 AM (MW) stations manually.
In some cases, test frequencies have been already stored
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You
can preset the stations you want into memory by following
the presetting method.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step 2.
On the remote control ONLY:
1 Tune in to the station you want to preset.
• See “Tuning in to a Station” on page 10.
2 Press PROGRAM.
“01” starts flashing on the display.
3 Press or to select a preset
number.
4 Press PROGRAM again.
“STATION STORED” appears on the display.
5 To preset more stations, repeat steps 1 to 4
above, allocating a different preset number to
each station.
PROGRAM
• Storing a new station on an already assigned number erases
the previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The preset stations will remain in the unit.
PROGRAM
Tuning in to a Preset Station
On the remote control ONLY:
1 Press TUNER/BAND to select either
“FM” or “AM.”
The unit automatically turns on and tunes in to
the previously received station—either FM or
AM (MW).
• Each time you press the button, the band alternates
between FM and AM (MW).
2 Press or to select a preset
number.
TUNER/
BAND
UX-S10[B]_C_06tuner_f.p65 06.3.10, 5:17 PM
11
Page: 14
12
Radio Data System allows FM stations to send an additional
signal along with their regular program signals. For example,
the stations send their station names, as well as information
about what type of program they broadcast, such as sports or
music, etc.
With the unit, you can receive the following types of Radio
Data System signals.
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
TEXT (Radio Text):
Shows text messages the station sends.
More about Radio Data System
• Some FM and AM (MW) stations do not provide Radio Data
System signals.
• Radio Data System services vary among FM Radio Data System
stations. For details on Radio Data System services in your area,
check with local radio stations.
• Radio Data System may not work correctly if the received station
is not transmitting the signals properly or if the signal strength is
weak.
Changing the Radio Data System Information
You can see Radio Data System information on the display
while listening to an FM station.
On the remote control ONLY:
Press REMAIN/PS/PTY/RT.
• Each time you press the button, the display
changes to show the following information:
• If no PS, PTY, or TEXT signals are sent by a station
“NO PS,” “NO PTY,” or “NO TEXT” appears on the display.
• On the characters displayed
When the display shows PS, PTY or TEXT signals:
–The display shows upper case letters only.
–The display cannot show accented letters; for example, “A” may
represent accented “A’s” like “Á, Â, Ã, À, Ä and Å.”
Searching for Programs by PTY Codes
(PTY Search)
One of the advantages of Radio Data System is that you can
locate a particular kind of program by specifying the PTY codes.
• For details on the PTY codes, see below.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step 1.
On the remote control ONLY:
1 Press REPEAT/PTY SEARCH
until the PTY code you want
appears on the display.
• Each time you press the button, the PTY
codes change as follows:
NEWS = AFFAIRS = INFO = SPORT =
EDUCATE = DRAMA = CULTURE =
SCIENCE = VARIED = POP M = ROCK M =
EASY M = LIGHT M = CLASSICS =
OTHER M = WEATHER = FINANCE =
CHILDREN = SOCIAL = RELIGION =
PHONE IN = TRAVEL = LEISURE = JAZZ =
COUNTRY = NATION M = OLDIES =
FOLK M = DOCUMENT = TEST = ALARM
=(back to the beginning)
2 Press ¢ or 4.
The unit searches FM stations,
stops when it finds the one you
have selected, and tunes in that
station.
• If no program is found, “NO MATCH” appears on the
display and the unit returns to the last received station.
To stop searching any time during the process, press
REPEAT/PTY SEARCH while searching.
Receiving FM Stations with Radio Data System
REMAIN/
PS/PTY/RT
REPEAT/
PTY SEARCH
PS
(Program Service)
PTY
(Program Type)
TEXT
(Radio Text)
Station frequency
(or preset channel no.)
Continued
UX-S10[B]_C_07RDS_f.p65 06.3.10, 5:17 PM
12
Page: 15
13
Description of the PTY codes:
NEWS: News.
AFFAIRS: Topical program expanding or enlarging
upon the news—debate, or analysis.
INFO: Program the purpose of which is to impart
advice in the widest sense.
SPORT: Program concerned with any aspect of
sports.
EDUCATE: Educational programs.
DRAMA: All radio plays and serials.
CULTURE: Programs concerning any aspect of national
or regional culture, including language,
theater, etc.
SCIENCE: Programs about natural sciences and
technology.
VARIED: Used for mainly speech-based programs
such as quizzes, panel games and
personality interviews.
POP M: Commercial music of current popular
appeal.
ROCK M: Rock music.
EASY M: Current contemporary music considered to
be “easy-listening.”
LIGHT M: Instrumental music, and vocal or choral
works.
CLASSICS: Performances of major orchestral works,
symphonies, chamber music, etc.
OTHER M: Music not fitting into any of the other
categories.
Classification of the PTY codes for some FM stations may be different from the above list on this page.
WEATHER: Weather reports and forecasts.
FINANCE: Stock Market reports, commerce, trading
etc.
CHILDREN: Programs targeted at a young audience.
SOCIAL: Programs about sociology, history,
geography, psychology and society.
RELIGION: Religious programs.
PHONE IN: Involving members of the public expressing
their views either by phone or at a public
forum.
TRAVEL: Travel information.
LEISURE: Programs about recreational activities.
JAZZ: Jazz music.
COUNTRY: Songs which originate from, or continue the
musical tradition of the American Southern
States.
NATION M: Current popular music of the nation or
region in that country’s language.
OLDIES: Music from the so-called “golden age” of
popular music.
FOLK M: Music which has its roots in the musical
culture of a particular nation.
DOCUMENT: Program concerning factual matters,
presented in an investigative style.
TEST: Broadcasts for testing emergency broadcast
equipment or receiver.
ALARM: Emergency announcement.
UX-S10[B]_C_07RDS_f.p65 06.3.10, 5:17 PM
13
Page: 16
14
Playing Back the Entire Disc—Normal Play
1 Press 0 OPEN on the unit.
The disc cover opens.
• You can insert a disc while listening to another source.
2 Place a disc correctly with its label side up.
3 Close the disc cover gently.
4 Press CD.
The unit automatically turns on and the
source changes to the CD player.
After loading the disc, the information below
appears on the display.
• “TOTAL GROUP XX” and “TOTAL TRACK XX”
(XX: group/track number) are shown on the display
after loading an MP3 disc.
• Total playing time does not appear when an MP3 disc is
loaded.
5 Press CD 3/8.
The first track of the disc starts playing.
• The disc automatically stops when the last track has
finished playing.
Playing Back Discs
This unit has been designed to play back the following
discs—CD, CD-R, and CD-RW.
When playing a CD-R or CD-RW
User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-
ReWritable) can be played only if they are already
“finalized.”
• Usually you can play back your original CD-Rs or CD-
RWs recorded in music CD format. However, sometimes
they may not play depending on their characteristics or
recording conditions.
• Before playing CD-Rs or CD-RWs, read their instructions
or cautions carefully.
• Some CD-Rs or CD-RWs may not play on this unit because
of their disc characteristics, damage or stain on them, or if
the player’s lens is dirty.
• CD-RWs may require a longer readout time. This is
because the reflectance of CD-RWs is lower than for
regular discs.
Notes for MP3 files
• The player can only recognize files with “MP3” or “mp3”
as the extensions, which can be in any combination of
upper and lower case. The file name needs to be up to 30
characters.
• This unit recognizes files (tracks) and folders (groups) on a
disc in the following conditions (including the root folder):
– up to 99 folders and 999 files.
– up to 8th layers.
• It is recommended that you record your material at a 44.1
kHz sampling rate, using the 128 kbps data transfer rate.
• Some MP3 files or discs may not be played back because
of their characteristics or recording conditions.
• MP3 discs requires a longer readout time than normal discs
because of the complexity of the folder/file configuration.
• MP3i and MP3 Pro are not available.
General notes
In general, you will have the best performance by keeping
your discs and the mechanism clean.
• Store discs in their cases, and keep them in cabinets or on
shelves.
• Keep the unit’s disc trays closed when not in use.
Continued use of irregular shape discs (heart-shape,
octagonal, etc.) can damage the unit.
Caution for DualDisc playback:
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard. Therefore, the
use of Non-DVD side of a DualDisc on this product may not
be recommended.
CD
CD
Good Not good
Continued
When playing
audio CD:
Elapsed
playing time
MP3 indicator
Elapsed
playing time
When playing MP3 disc:
Current track
number
Current track
number
Total track
number
Total playing
time
Total track
number
When stop playing
MP3 disc:
When stop playing
audio CD:
Total group
number
Group folder indicator
UX-S10[B]_C_08CD_f.p65 06.3.10, 5:18 PM
14
Page: 17
15
Programming the Track Playing Order—Program Play
You can arrange the order in which tracks play before you
start playing. You can program up to 60 tracks.
On the remote control ONLY:
1 Place a disc.
• If the current source is not the CD player, press CD.
2 Press PROGRAM.
The PRGM (program) indicator starts flashing
on the display.
3 Select the track you want to
program.
1) (MP3 disc only)
Press or repeatedly to
select the group.
2) Press ¢ or 4 repeatedly to
select the track, then press PROGRAM.
“P XX OK” (XX: the program step number)
appears on the display for a while.
4 Repeat step 3 to program other tracks you
want.
5 Press CD 3/8.
The tracks are played in the order you have programed.
If you try to program a 61st track
“PRG FULL” will appear on the display.
To stop playing, press 7.
Basic Disc Operations
While playing a disc, you can do the following operations.
To stop playing for a moment
During play, press CD 3/8.
While pausing, the elapsed playing time flashes on
the display.
To resume playing, press CD 3/8 again.
To go to another track
Before or during play, press ¢ or
4 repeatedly.
• ¢ : Skips to the beginning of the
next or succeeding tracks.
• 4 : Goes back to the beginning of the current or previous
tracks.
When playing back MP3 disc:
• : Skips to the first track of the next group.
• : Skips to the first track of previous group.
To locate a particular point in a track
During play, press and hold ¢ or
4.
• ¢ : Fast-forwards the tracks.
• 4 : Fast-reverses the tracks.
• You cannot use this function when playing back an MP3
disc.
CD
PROGRAM
PROGRAM
CD
While playing back an MP3 disc
ID3 Tag information (the name of the title, artist, and album up to 30
characters) will be shown on the display. When the name is too long
to be displayed at once, it is scrolled.
This unit supports ID3 Tag ver. 1.1 and 2.0.
To stop playing, press 7.
To remove the disc, press 0 OPEN on the unit.
• If the disc cannot be read correctly (because it is scratched,
for example) or an unreadable CD-R or CD-RW is inserted
Playback will not start.
• If no disc is inserted
“NO DISC” appears on the display.
DO NOT try to open the disc cover by hand as it
will be damaged.
MP3 disc:
audio CD:
Track number
Program step
number Group number Track number
To check the program contents
Press ¢ or 4 repeatedly in stop
mode.
The program number and track number
are displayed in succession.
UX-S10[B]_C_08CD_f.p65 06.3.10, 5:18 PM
15
Page: 18
16
REMAIN
TOTAL REMAIN
TOTAL
When playing back an MP3 disc:
1: Repeats one track.
In Random Play, this function is not available.
ALL: In Normal Play, repeats all the tracks.
In Program Play, repeats all the tracks in the
program.
GR.: In Normal Play, repeats all the tracks in a
group.
In Program Play and Random Play, this
function is not available.
Playing at Random—Random Play
You can play the tracks at random.
On the remote control ONLY:
Press RANDOM when CD is the source.
The RAND indicator lights up on the display. The
random playback starts and continues until you stop
the playback.
RANDOM
To exit from Random Play, press RANDOM again.
The RAND indicator goes off, and playback
continues in the normal order.
To stop playing, press 7. The random play function
is automatically deactivated.
• It is not possible to active the random play function
during Program Play.
RANDOM
ALL
1
1: Repeats one track.
ALL: In Normal Play, repeats all the tracks.
In Program Play, repeats all the tracks in the
program.
Repeat indicators
Displaying various information
You can display the playback information of the audio CD
and various information of MP3 tracks.
On the remote control ONLY:
Press REMAIN/PS/PTY/RT repeatedly.
When playing back an audio CD:
• Each time you press the button, the display
changes as follows, and the following indicators
light up on the display:
REMAIN: Shows the remaining time of the current
track.
TOTAL: Shows the elapsed time of the disc.
TOTAL REMAIN: Shows the remaining time of the disc.
No indication: Shows the elapsed time of the current
track.
When playing back an MP3 disc:
• Each time you press the button, the information below is
shown for a while on the display and returns to the normal
indication:
* Displayed only while playing back.
Some characters may not be shown correctly.
REMAIN/
PS/PTY/RT
Repeating Tracks—Repeat Play
You can play tracks repeatedly in various ways.
On the remote control ONLY:
Press REPEAT/PTY SEARCH
repeatedly when CD is the source.
• Each time you press the button, Repeat Play
changes as follows, and the following repeat
indicator lights up on the display:
ALL
GR.
1
Canceled
Canceled
REPEAT/
PTY SEARCH
To cancel Repeat Play, press REPEAT/PTY
SEARCH repeatedly until the repeat indicator goes
off.
• Repeat Play and Random Play cannot be used at the same
time.
No indication
To modify the last programmed track
Press PROGRAM in stop mode, then repeat step 3
above. To finish modifying and start playback,
press CD 3/8.
• You cannot modify the program after programming the
60th track.
To clear the program and exit the program play
mode
Press 7 in stop mode.
“PRG CLR” appears and the PRGM indicator disappears on the
display.
PROGRAM
• Changing the source and turning the power off also clear
the program.
ID3 tag
information*
Group name/
Track (file) name
REPEAT/
PTY SEARCH
UX-S10[B]_C_08CD_f.p65 06.3.10, 5:18 PM
16
Page: 19
17
For Tape operations, use buttons inside the front cover on the
unit.
Playing Back a Tape
You can play back type I tapes only.
On the unit ONLY:
1 Open the front cover.
2 Press &/) (stop/cassette holder open).
The cassette holder opens.
3 Put a cassette in with the exposed part of the
tape down.
Playing Back Tapes
5 Press TAPE.
The unit automatically turns on and the
source changes to the tape deck.
• You can select to the tape by pressing TAPE
on the remote control.
6 Press # (play).
The tape starts playing.
• When the end of the tape is reached, playing
stops.
To stop playing, press &/).
To stop playing for a moment, press * (pause).
To resume playing, press * again.
To fast forward or rewind the tape, press
⁄ or !.
• The tape stops at the end of the fast
forwarding or rewinding. To release the
locked button, press &/).
To remove the cassette, press &/) while
playback is stopped.
TAPE
• DO NOT turn off the unit while playing back or
recording a tape. The cassette deck or tapes
may be damaged.
• The use of C-120 or longer tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinch
rollers and the capstans.
• This unit is not compatible with type II and type
IV tapes.
4 Close the cassette holder gently.
UX-S10[B]_C_09tape_f.p65 06.3.10, 5:18 PM
17
Page: 20
18
IMPORTANT:
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast or cable program and in any
literary, dramatic, musical, or artistic embodied
therein.
• The recording level is automatically set correctly, so it is
not affected by the other sound settings. Thus, during
recording you can adjust the sound you are actually
listening to without affecting the recording level.
• If recordings you have made have excessive noise or static,
the unit may be too close to a TV. Increase the distance
between the TV and the unit.
• You can only use type I tape for recording.
• DO NOT turn off the unit while playing back or
recording a tape. The cassette deck or tapes
may be damaged.
• DO NOT use type II and type IV tapes since the
unit is not compatible with such tapes.
• The use of C-120 or longer tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinch
rollers and the capstans.
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus, when
recording from discs, FM/AM broadcasts, or external equipment,
wind the leader tape first to ensure that the recording will be made
without losing any music.
To protect your recordings
Cassettes have two small tabs on the back to protect against
unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
Recording
Adhesive tape
Recording from the Radio
On the unit ONLY:
1 Put a recordable cassette in with the exposed
part of the tape down.
• See also page 17.
2 Close the cassette holder gently.
3 Press TUNER/BAND to select either
“FM” or “AM.”
• When recording from discs, see “Recording
Discs—Disc Synchronized Recording” on page
19.
4 Tune in to the station you
want to record.
5 Press ‡ (recording).
‡ and # lock down, and the recording starts.
You cannot press ‡ in the following cases:
• If no cassette is inserted.
• If a protected tape is inserted.
To stop recording for a moment, press *
(pause).
To resume recording, press * again.
To stop recording, press &/).
To remove the cassette, press &/) while
recording is stopped.
To record an AM (MW) station—Beat Cut
On the remote control ONLY:
While recording an AM (MW) broadcast, beats
may be heard (which are never heard when
listening to the broadcast without recording it).
If this occurs, press BEAT CUT repeatedly, while
recording, until the beats are reduced.
• Each time you press the button, the display alternates
between “CUT–1” and “CUT–2.”
BEAT CUT
TUNER
BAND
Continued
UX-S10[B]_C_10rec_f.p65 06.3.10, 5:18 PM
18
Page: 21
19
Recording Discs
—Disc Synchronized Recording
You can start disc play and recording at the same time.
On the unit ONLY:
1 Put a recordable cassette in with the exposed
part of the tape down.
• See also page 17.
2 Close the cassette holder gently.
3 Press CD to select the CD player as
the source.
4 Press ‡ (recording).
The SYNC indicator appears on the display
and the CD starts playback automatically and
the recording starts.
• When the end of the tape is reached, recording stops and
the CD player is paused.
• If you press ‡ while playing back a track, the unit starts
playback and recording from the beginning of the track.
CD
You cannot press ‡ in the following cases:
• If no cassette is inserted.
• If a protected tape is inserted.
To stop recording for a moment, press *.
The recording is paused, but the CD playback
does not stop.
To resume recording, press * again.
To stop recording, press &/).
The recording stops and the CD playback is
paused.
To remove the cassette, press &/) while
recording is stopped.
Pressing DISPLAY/CLOCK SET does not show the time indication
while recording (“REC ON” appears on the display).
UX-S10[B]_C_10rec_f.p65 06.3.10, 5:18 PM
19
Page: 22
20
3 Press ¢ or 4
repeatedly to adjust the
timer-playback volume.
Press PROGRAM after adjusting
the volume.
The ON (on-time) indicator appears
and the hour indication starts flashing.
4 Set the on-time you want the unit to turn on.
1) Press ¢ or 4 to set the
hour, then press PROGRAM.
2) Press ¢ or 4 to set the
minute, then press
PROGRAM.
The OFF (off-time) indicator appears and the
hour indication starts flashing.
5 Set the off-time you want the unit to turn off.
1) Press ¢ or 4 to set the
hour, then press PROGRAM.
2) Press ¢ or 4 to set the
minute, then press
PROGRAM.
“TIMER OK” appears on the display for a
while.
6 Press TIMER ON/OFF to activate
the daily timer mode.
Each time you press the button, the Daily
Timer alternates on and off.
While activating the Daily Timer, the (timer) indicator
lights up on the display.
• You can active the Daily Timer by pressing
TIMER ON/OFF on the unit.
7 Press STANDBY/ON to turn off the unit
if the unit is on.
Using the Timers
On the remote control ONLY:
1 Press TIMER SET, then press
PROGRAM.
The (timer) indicator appears and the source
indication starts flashing on the display.
2 Select the source to play.
1) Press ¢ or 4 to select
CD, FM, or AM, then press
PROGRAM.
2) (For FM and AM only)
Press ¢ or 4 to select the preset
station you want, then press PROGRAM.
The volume indication starts flashing on
the display.
Daily Timer and Sleep Timer are available.
• Before using these timers, make sure the built-in clock is
set correctly (see page 8).
Using the Daily Timer
You can set the Daily Timer when the unit is either turned on
or in standby mode.
How the Daily Timer actually works
When the on-time comes, the unit automatically turns on and
then the off-time comes, the unit automatically turns off
(standby).
• Once the timer has been set, it will be activated at the same
time everyday until the timer is turned off and the timer
setting remains in memory until you change it.
Before you start...
You can select CD, FM, or AM as the source of the Daily
Timer playback.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step 1.
PROGRAM
PROGRAM
Continued
SET
TIMER
PROGRAM
PROGRAM
PROGRAM
ON/OFF
TIMER
UX-S10[B]_C_11timer_f.p65 06.3.10, 5:18 PM
20
Page: 23
21
To deactivate the timer temporarily, press
TIMER ON/OFF until the (timer) indicator
goes off.
To activate and change the timer, repeat steps 1 to 7 on
page 20.
• To activate the timer again without changing
the setting, press TIMER ON/OFF until the
(timer) indicator lights up on the display.
If the unit is already turned on when the timer on-time
comes
The timer does not work.
When no disc is set for the Daily Timer playback
The source will automatically change from CD to the last station
you tuned in to, and start playing when the on-time comes.
When you unplug the AC power cord or if a power
failure occurs
The timer will be canceled. You need to set the clock first, then set
the timer again.
Using the Sleep Timer
With the Sleep Timer, you can fall asleep to your favorite
music or radio program.
• You can set the Sleep Timer only when the unit is turned
on.
How the Sleep Timer actually works
The unit automatically turns off after the specified length of
time passes.
On the remote control ONLY:
1 Press SLEEP.
The SLEEP indicator lights up on the display.
• Each time you press the button, the length of time
changes as follows:
2 Wait for about 5 seconds after specifying the
length of time.
To check the remaining time until shut-off time, press
SLEEP once. The remaining time until shut-off time appears
for about 5 seconds.
To change the shut-off time, press SLEEP repeatedly until
the length of time you want appears.
To cancel the setting, press SLEEP repeatedly until “OFF”
appears and the SLEEP indicator goes off on the display.
• Turning off the unit also cancels the Sleep Timer.
When you set the Sleep Timer after the Daily Timer
starts playing the selected source
The unit turns off with either timer having an earlier shut-off time.
If you set the Sleep Timer while playing back or
recording a tape
Do not shut the unit off with the Sleep Timer while a tape is running.
If the unit turns off while playing back or recording a tape, the
cassette deck or tapes may be damaged.
90
OFF
80
10
70 60 50
20 30 40
SLEEP
ON/OFF
TIMER
ON/OFF
TIMER
UX-S10[B]_C_11timer_f.p65 06.3.10, 5:18 PM
21
Page: 24
22
Maintenance
To get the best performance of the unit, keep your discs, tapes and mechanism clean.
General Notes
In general, you will have the best performance by keeping
your discs, tapes and the mechanism clean.
• Store discs and tapes in their cases, and keep them in
cabinets or on shelves.
Cleaning the unit
• Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or have its paint peel off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as an
insecticide to it.
– DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
Handling discs
• Remove the disc from its case by
holding it at the edge while pressing
the center hole lightly.
• Do not touch the shiny surface of the
disc, or bend the disc.
• Put the disc back in its case after use
to prevent warping.
• Be careful not to scratch the surface
of the disc when placing it back in
its case.
• Avoid exposure to direct sunlight,
temperature extremes, and moisture.
To clean the disc
Wipe the disc with a soft cloth in a
straight line from center to edge.
DO NOT use any solvent—such as conventional
record cleaner, spray, thinner, or benzine—to clean
the disc.
Handling cassette tapes
• If the tape is loose in its cassette, take up the
slack by inserting a pencil in one of the reels
and rotating.
• If the tape is loose, it may get stretched, cut,
or caught in the cassette.
• Be careful not to touch the tape surface.
• Avoid storing tapes in any of the following
places:
– In dusty places
– In direct sunlight or heat
– In moist areas
– On a TV or speaker
– Near a magnet
To keep the best recording and playback sound quality
You need to clean the heads.
• Clean the heads after every 10 hours of use with
a wet-type head cleaning tape (available at electronic and
audio shops).
When the head becomes dirty, the following symptoms will
occur:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any metallic or
magnetic tools.
To demagnetize the head
Turn off the unit, and use a head demagnetizer (available at
electronic and audio shops).
Pinch Roller
Capstan
Head
UX-S10[B]_C_12ext_f.p65 06.3.10, 5:18 PM
22
Page: 25
23
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,
such as your dealer, for service.
Troubleshooting
Symptom
Power does not come on.
No sound is heard.
Hard to hear broadcasts because of
noise.
The disc does not play.
Impossible to record.
Operations are disabled.
Unable to operate the unit by the remote
control.
Possible Cause
The power cord is not connected to an
AC outlet.
• Connections are incorrect or loose.
• A pair of headphones is connected.
• MP3 disc is recorded with “packet
writing.”
• Antennas are disconnected.
• The AM (MW) loop antenna is too
close to the unit.
• The FM antenna is not properly
extended and positioned.
The disc is upside down.
Small tabs on the back of the cassette are
removed.
The built-in microprocessor has
malfunctioned due to external electrical
interference.
• The path between the remote control
and the remote sensor on the unit is
blocked.
• The batteries are exhausted.
• You are using the remote control too
far from the unit.
Action
Insert the plug into the socket.
• Check all connections and make
corrections. (See pages 6 and 7.)
• Unplug the headphones from the
PHONES jack.
• It cannot be played. Replace the disc.
• Reconnect the antenna correctly and
securely.
• Change the position and direction of
the AM (MW) loop antenna.
• Extend FM antenna and orient to the
best reception position.
Put the disc in with the label side up.
Cover the holes with adhesive tape.
Unplug the AC power cord then plug it
back in.
• Remove the obstruction.
• Replace the batteries. (See page 6.)
• Signals cannot reach the remote
sensor. Move closer to the unit.
UX-S10[B]_C_12ext_f.p65 06.3.10, 5:18 PM
23
Page: 26
24
Amplifier Section—CA-UXS10
Output Power (IEC 268-3): 10 W (5 W + 5 W) at 4 Ω (10% THD)
Speakers/Impedance: 4 Ω – 16 Ω
Tuner
FM tuning range: 87.50 MHz—108.00 MHz
AM (MW) tuning range: 522 kHz—1 629 kHz
CD player
Dynamic range: 85 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
Cassette deck
Frequency response:
Normal (type I): 100 Hz—10 000 Hz
Wow and flutter: 0.35 % (WRMS)
General
Power requirement: AC 230 V , 50 Hz
Power consumption: 22 W (at operation)
3.0 W (on standby)
Dimensions (W/H/D) (approx.): 145 mm x 209 mm x 226 mm
Mass (approx.): 2.8 kg
Supplied accessories
See page 6.
Speaker Section—SP-UXS10
Type: Full range Bass-reflex type
Speakers: 10 cm cone x1
Power handling capacity: 5 W
Impedance: 4 Ω
Frequency range: 100 Hz to 15 kHz
Dimensions (W/H/D) (approx.): 135 mm x 209 mm x 152 mm
Mass (approx.): 1.3 kg each
Specifications Design and specifications are subject to change without notice.
UX-S10[B]_C_12ext_f.p65 06.3.10, 5:18 PM
24
Page: 27
EN
0306NYMMDWORI
© 2006 Victor Company of Japan, Limited
UX-S10
MICRO
COMPONENT
SYSTEM
UX-S10[B]_C_01cover_f.p65 06.3.10, 5:17 PM
2

Question & answers

There are no questions about the JVC UX-S10 yet.

Ask a question about the JVC UX-S10

Have a question about the JVC UX-S10 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC UX-S10. Please make sure that you describe your difficulty with the JVC UX-S10 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.