JVC UX-N1 manual

View a manual of the JVC UX-N1 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: JVC
  • Product: Hi-Fi system
  • Model/name: UX-N1
  • Filetype: PDF
  • Available languages: Dutch, English, German

Table of Contents

Page: 0
SPEAKERS
PHONES
RIGHT
IMPEDANCE
MIN
LEFT
ANTENNA
COAXIAL
AM EXT
LOOP
MICRO COMPONENT SYSTEM
UX-N1S
—Consists of CA-UXN1S and SP-UXN1S
UX-N1W
—Consists of CA-UXN1W and SP-UXN1W
INSTRUCTIONS
GNT0065-001B[B]
0106MOCMDWJSC
©2006 Victor Company of Japan, Limited
1 3
2 4
Connections
Do not connect the AC power cord until all other connections have been made.
Basic and Common Operations
This System can play back the following discs—regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3 format).
• When playing back the MP3 track, MP3 indicator appears on the display.
To Set a Disc
1 On the System
2 3 On the System
The disc cover on the
System opens.
Place a disc correctly with its label side up, then
press down on the portions around the disc’s
center hole until you hear a click.
• When removing the disc, take out the disc
by holding it at the edge with pressing the
System’s pivot lightly.
The disc cover on the
System closes.
• Do not close forcibly
the disc cover with
the hand.
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue: Neutral
Brown: Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Warnings, Cautions and Others
Caution — button!
Disconnect the mains plug to shut the power off completely.
When installing the apparatus, ensure that the plug is easily
accessible.
The button in any position does not disconnect the
mains line. The power can be remote controlled.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Information for Users on Disposal of Old Equipment
[European Union only]
This symbol indicates that the product with this symbol should not be disposed as general household waste. If
you want to dispose of this equipment, please do not use the ordinary dust bin! There is a separate collection
System for these products.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
Front view Side view
15 cm
15 cm
10 cm
15 cm
1 cm
15 cm
15 cm
1 cm
SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W
About the cooling fan
A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring
normal operation of the unit.
Supplied Accessories
After unpacking, check to be sure that you have all the
following items. The number in parentheses indicates the
quantity of each piece supplied.
• Remote control (x 1)
• Lithium coin battery CR2025 (x 1) (The battery has been
installed when shipped from the factory.)
• AM loop antenna (x 1)
• FM antenna (x 1)
If anything is missing, consult your dealer immediately.
To a wall outlet
Plug the AC power cord only after
all connections are complete.
AM loop antenna
(supplied)
Turn it until the best
reception is obtained.
To assemble the AM loop antenna
To connect the AM loop antenna
To connect the speaker cords
Make sure the both speakers are connected correctly and
firmly.
When connecting the speaker cords, match the polarity of
the speaker terminals: white cord to (+) and white cord with
black stripe to (–).
NOTES
• DO NOT connect more than one speaker
to each terminal.
• DO NOT allow the conductor of the
speaker cords to be in touch with the
metallic parts of the System.
NOTES
• Make sure the antenna conductors do not touch any other terminals,
connecting cords and power cord. Also, keep the antennas away from
metallic parts of the System, connecting cords, and the AC power cord.
This could cause poor reception.
• If the cords are covered with vinyl, remove the vinyl to expose the tip
of the cord by twisting the vinyl.
Programming the Playing Order—Program
Play (except for MP3)
1 Press repeatedly until the PRGM (program) indicator
appears on the display before you start playback.
2 or Select the track number to program.
3 Press to program the selected track.
4
Repeat step 2 and 3 to program other tracks you want.
• If you try to program a 33rd track,“FULL”will appear on the
display.
5 The tracks are played in the order you have
programmed.
Operations on the Program Play Mode
To Press
Check the
programmed
contents
or Press while playback is stopped.
To erase the
last step
To erase
the entire
program
Press while playback is stopped.
To exit from
program play
Press twice while playback is
stopped to exit from the program
play.
• The stored program is erased.
Playing at Random—Random Play
1 Press until the RND (random) indicator appears on
the display before you start playback.
2
Playback starts in random order.
Random Play ends when all tracks are played.
Operations on the Random Play Mode
To Press
To skip a track • 4 does not work.
To exit from
random play
Press once while playback is
stopped to exit from the random
play.
Playing Repeatedly—Repeat Play
1
Press repeatedly before you start playback to specify
the repeat mode as follows:
REP 1 REP GRP
(MP3 only)
REP OFF REP ALL
REP 1
Repeats the current (or specified)
track.
REP GRP
Repeats all tracks in the current
group. (MP3 only)
REP ALL Repeats all tracks.
REP OFF Normal playback
2
Basic Disc Operations
To
Press
On the
System
On the
remote
Playback the disc
Current track number and elapsed playing
time appear on the main display.
• During playback, press again to stop
playing for a moment.
Stop playback
• While playback is stopped, total track
number and total playing time (for MP3
disc, group number and track number)
appear on the main display.
Select a track
Increases the track numbers.
Decreases the track numbers.
Select a group (MP3
only)
—
Increases the group numbers while playback
is stopped.
—
Decreases the group numbers while playback
is stopped.
Forward search /
Reverse search
—
Fast-forwards the track by pressing briefly.
To stop searching, press 6.
—
Fast-reverses the track by pressing briefly.
To stop searching, press 6.
NOTES
• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or
CD-RW is loaded, playback will not start.
• If no disc is inserted, “NO DISC” appears on the main display.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small
amount of power (3.6 W) is always consumed while the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring.
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult
your dealer.
1 Hold
2 Insert
3 Release
Outdoor FM antenna
(not supplied)
For better FM/AM reception
FM antenna (supplied)
Extend it so that you can obtain the best reception.
Getting Started
NOTE
DO NOT turn off (standby)
the System with the volume
set to an extremely high level;
Otherwise, the sudden blast
of sound can damage your
hearing, speakers and/or
headphones when you turn
on the System or start
playback.
Using Headphones
Be sure to turn down the volume before connecting or wearing
the headphones.
• Connecting the headphones will deactivate the speakers.
Operating on the System
To Press
Turn on or off (standby) the
power
The standby lamp on the System turns off/on.
Select a source*
See“Playing Back Discs”on page 4.
See“Listening to FM and AM Broadcasts”on
page 5.
See“Connecting a Portable Audio Device”on
page 6.
Adjust the volume
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
Operating on the Remote Control
To Press
Turn on or off
(standby) the power
The standby lamp on the System turns off/on.
Select a source
See“Playing Back Discs”on page 4.
See“Listening to FM and AM Broadcasts”on
page 5.
See“Connecting a Portable Audio Device”on
page 6.
Adjust the volume
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
Drop the volume in a
moment
To restore the volume, press again, or adjust
the volume level.
Reinforce the bass
sound
AHB PRO indicator appears on the display.
To cancel this function, press again.
Adjust the tone (Bass/
Treble)
Press once to adjust the bass level or press
twice to adjust the treble level.
Then press VOLUME + to increase the level or
press VOLUME – to decrease it.
• You can adjust the bass and treble level from
–3 to +3.
Changing the display
brightness
Press when the System is turned on.
To cancel this function, press again.
Set the SAVE mode
Press and hold for more than 2 seconds when
the System is on standby.
To cancel this function, press and hold for
more than 2 seconds again.
• Setting the SAVE mode allows you to reduce
power consumption by turning the display
off while on standby.
Changing the display
information (Clock
and Source)
Press briefly (except for FM mode).
For setting the clock, see page 7.
Turn off the System
automatically after CD
playback is over
(AUTO STANDBY
function)
Press and hold until A.STBY indicator appears
on the display.
To cancel this function, press and hold again.
• If no operation is done for about 3 minutes
after CD playback stops, the System turns off.
Turn off the System by
using the sleep timer
Press briefly and repeatedly to specify the time
(in minutes) as follows:
10 20 30 60 90 120 150
Canceled
• To check the time remaining until the shut-off time after
setting the sleep timer, press SLEEP once.
Point it at the remote sensor on
the front panel. (The operating
range is approx. 7 m.)
Playing Back Discs
1 Hold
2 Insert
3 Release
Disconnect the supplied FM antenna,
and connect to an outdoor FM antenna
using a 75 Ω wire with coaxial type
connector (IEC or DIN45325).
AM loop antenna
Keep it connected.
Vynile-covered wire (not supplied)
Extend it horizontally.
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Display Information
Disc play mode indicators (See page 4.)
Tuner mode indicators
(See page 5.)
Timer mode indicators
(See the right column and page 7.)
QP Link indicator
(See page 6.)
Main Display
AHB PRO and A.STBY indicator (See the right column.)
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the System; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
The model information is located on the bottom.
Prepare the Remote Control
When you use the remote control
for the first time, pull out the
insulation sheet.
Insulation sheet
Replacing the Battery in the Remote Control
Insert the battery into the
remote control by matching the
polarity (+ and –) correctly.
Lithium coin battery
(product number: CR2025)
STANDBY lamp
* You can operate the source select
buttons on the System only touch
lightly, because these buttons are
“touch sensor panel.”
If you touch any one of these
buttons, they lights in blue briefly.
NOTES
• Store the battery in a place where children cannot reach. If a child accidentally swallows the
battery, consult a doctor immediately.
• Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of
these things may cause the battery to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic materials. Doing this may cause the battery to
give off heat, crack, or start a fire.
• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to
give off heat, crack, or start a fire.
• Dispose of battery in the proper manner, according to federal, state, and local regulations.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Page: 1
This System has LINE IN/OUT jacks to connect a portable audio device.
Connect between the device and the System by using the stereo mini plug cord (not supplied).
IMPORTANT:
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or
artistic embodied therein.
5 7
6 8
Setting the Clock and Daily Timer
Troubleshooting Maintenance
SpecificationsSpecifications and appearance are subject to change without prior notice.
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before
you finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
Disc Operations
The disc does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ MP3 disc is recorded with the“packet writing (UDF file).”
It cannot be played.
Check the files you want to play back.
ID3 Tag on an MP3 disc cannot be shown.
\ There are two types of ID3 Tag—Version 1 and Version 2.
This System can only show ID3 Tag Version 1.
MP3 groups and tracks are not played back as you
expect.
\ The playing order is determined when the disc was
recorded. It depends on the writing application.
The disc sound is discontinuous.
\ The disc is scratched or dirty.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
To get the best performance of the System, keep your discs
and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strong.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
Amplifier section
OUTPUT POWER:
10 W (5 W + 5 W) at 4 Ω (10% THD)
Speakers/Impedance: 4 Ω – 16 Ω
Audio Input LINE IN: 500 mV/47 kΩ (at“LINE IN LVL1”)
250 mV/47 kΩ (at“LINE IN LVL2”)
125 mV/47 kΩ (at“LINE IN LVL3”)
Audio Output LINE OUT: 1.0 Vrms (10 kΩ) (at“LINE OUT LVL1”)
2.0 Vrms (10 kΩ) (at“LINE OUT LVL2”)
Tuner section
FM Tuning range: 87.50 MHz - 108.00 MHz
AM (MW) Tuning range: 522 kHz - 1 629 kHz
CD player section
Dynamic range: 88 dB
Signal-to-noise ratio: 93 dB
Wow and flutter: Immeasurable
Speakers
Speaker units: 8 cm cone x 1
Impedance: 4 Ω
Dimensions (approx.): 130 mm x 171 mm x 136 mm (W/H/D)
Mass (approx.): 0.75 kg each
Supplied Accessories
See page 2.
General
Power requirements: AC 230 V ~ , 50 Hz
Power consumption:
20.0 W (POWER ON), 3.6 W (STANDBY mode)
3.0 W or less (SAVE mode)
Mass: 1.8 kg
Dimensions (W x H x D): 270 mm x 68.5 mm x 203 mm
Changing the Radio Data System
Information
Each time you press the button, the main display
changes as follows:
PS PTY
Frequency
(Non-Radio Data System signal)
RT
NOTE
If no Radio Data System signals are sent by a station,“NO PS,”
“NO PTY,”or“NO RT”appears on the main display.
Searching for Programs by PTY Codes
(PTY Search)
You can locate a particular kind of program from the preset
stations (see the left column) by specifying the PTY codes.
1
Press to enter the PTY code setting
mode.
“PTY”and“SELECT”appear on the main
display.
2 or Select a PTY code.
3
The System searches 30 preset FM
stations, stops when it finds the one
you have selected, and tunes in to that
station.
NOTES
• To stop searching any time during search, press PTY SEARCH.
• To continue searching after it stops on an unwanted station,
press PTY SEARCH while the indications on the display are
flashing.
• If no program is found,“NOTFOUND”appears on the main
display.
Receiving FM Stations with Radio Data System
Radio Data System allows FM stations to send an additional signal along with their regular program signals.
With the System, you can receive the following types of Radio Data System signals.
PS (Program Service): Shows commonly known station names.
PTY (Program Type): Shows types of broadcast programs.
RT (Radio Text): Shows text messages the station sends.
Enhanced Other Networks: Provides the information about the types of the programs broadcast by the Radio Data System
stations of the different networks.
NOTE
If you want to know more about Radio Data System, visit <http://www.rds.org.uk>.
Switching Temporarily to a Program
of Your Choice Automatically
The Enhanced Other Networks function allows the System
to switch temporarily to a preset FM station broadcasting a
program of your choice (TA, NEWS, or INFO).
• This function works while listening to an FM station
providing the required signals.
Press repeatedly to select the program type as
follows:
TA NEWS
OFF INFO
TA Traffic announcement in your area.
NEWS News
INFO
Program the purpose of which is
impart advice in the widest sense.
How the Enhanced Other Networks function actually
works:
When a station starts broadcasting the program of your
choice, the System automatically switches to the station.
The PTY code indicator starts flashing.
After the program is over, the System goes back to the
previously tuned station, but the function still remains
active (the indicator stops flashing and remains lit).
Basic Tuner Operations
To
Press
On the System On the remote
Select FM or AM
Each time you press the button, the band
alternates between FM and AM.
• “FM” or “AM” and selected frequency
appear on the main display.
• If an FM program is broadcast in stereo,
the ST (stereo) indicator lights up on the
display (only when the reception is good).
Select a frequency or or
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.
Tune in to a preset station — or
Press to select a preset number for the
station you store.
• For presetting stations, see below.
Change the FM reception mode
(When an FM stereo broadcast
is hard to receive or noisy)
—
Press to improve reception.
The MONO indicator appears on the display.
Reception will improve though the stereo
effect is lost.
To restore the stereo effect, press again.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
1
Tune in to a station you want to preset.
• You can also store the monaural reception mode for FM preset stations if
selected.
2
Press to activate the preset number entry mode.
• Finish the following process while the indication on the display
is flashing.
3 or Press to select a preset number for the station you store.
4 Press to store the station.
NOTE
When you unplug the AC power cord or if a power failure occurs, the preset stations
will be erased in two days.
Setting the Clock
Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
1
Press to activate the clock setting mode.
• If you have already adjusted the clock before, press the
button repeatedly until the clock setting mode is selected.
2 or Adjust the hour, then the minute.
• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of Daily Timers at the same time.
1
Press repeatedly to select one of the timer setting modes you want to set—Daily 1 ON time, Daily
2 ON time, or Daily 3 ON time—as follows:
Daily 1 Timer Daily 2 Timer
Daily 1 ON (Time) Daily 2 ON (Time)
Canceled Clock setting ON (Time) Daily 3
(See above.) Daily 3 Timer
2 or
1Adjust the hour then the minute for on-time.
2Adjust the hour then the minute for off-time.
3Select the playback source—“FM/AM,”“CD,”or “LINE.”
4For“FM/AM”: Select a preset channel.
For“LINE”: Make the external device ready for playback.
5Select the volume level.
• You can select the volume level (“VOLUME 0”to“VOLUME 31”and“VOLUME – –”). If you select
“VOLUME – –,”the volume is set to the last level when the System is turned off.
3 Turn off the System (on standby).
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
To turn off the Daily Timer
1 Press repeatedly to select“Daily 1,”“Daily 2,”or“Daily 3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
Connecting a Portable Audio Device
1 “LINE”appears on the main display.
2 Start playing the device connected.
3 Adjust the volume level to the level
you want to listen to.
To Adjust the Audio Input Level
If the sound from the device connected to the LINE IN
jack is too loud or too quiet, you can change the audio
input level through the LINE IN jack (without changing
the volume level).
On the remote Press and hold for more than 2 seconds
while“LINE”is selected as a source.
You can select one of three levels
alternately.
To Play Back a Portable Audio Device
Easily
By using QP Link (Quick Portable Link), you can easily start
playing back a portable audio device connected to the
LINE IN jack.
On the remote Press and hold for more than 2 seconds
to activate QP Link.
QP Link indicator appears on the display.
To cancel this function, press and hold
for more than 2 seconds again.
When QP Link is activated, connecting a portable device
to the LINE IN jack and starting playback performs the
following:
• While listening to another source...
Changes the source to“LINE”automatically. (If you
change from“LINE”to another source, QP Link will be
canceled.)
• While the System is on standby...
Turns on the System and changes the source to“LINE”
automatically (except when the display is turned off).
NOTE
See“Learning More about This System”on page 7.
1 Start recording or standby recording on the device.
2 or
Start playing the CD or tune into the station you want to
recording.
To Select the Audio Output Level
If the recorded sound on the device connected to the LINE OUT jack is too loud or
too quiet, you can change the audio output level through the LINE OUT jack (without
changing the volume level).
On the System
Press to change the audio output level.
You can select one of two levels alternately as follows:
OUT_LVL1 OUT_LVL2
Learning More about This System
Basic and Common Operations (see page 3)
• Sound adjustments also affect the sound through the
headphones.
• Sound adjustments do not affect recording to the external
device.
• You can set the clock and daily timer while the SAVE mode
is turned on. While setting the clock or daily timer, the
display is turning on.
Playing Back Discs (see pages 4)
• This System cannot play“packet write”discs.
• For MP3 playback...
– MP3 discs are required a longer readout time than regular
CDs. (It depends on the complexity of the group/file
configuration.)
– Some MP3 files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3 discs, use ISO 9660 Level 1 or Level 2
for the disc format.
– This System can play back MP3 files with the extension
code <.mp3> (regardless of the letter case—upper/
lower).
– It is recommended that you make each MP3 file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at bit rate of less than
64 kbps.
– Playback order of MP3 tracks may be different from the
one you have intended while recording. If a folder does
not include MP3 tracks, they are ignored.
• This System can recognize up to 511 tracks in a disc. Also,
the System can recognize up to 150 tracks per group and
up to 99 groups in a disc. (for MP3)
– If there are any unplayable files in a folder, those files are
also counted in the total file number.
– Playable files which do not belong to any groups are
handled as Group 1.
MP3 groups/tracks configuration
This System plays back MP3 tracks as follows.
Hierarchy
Level 1 Level 2 Level 3 Level 4 Level 5
Group with its play order
MP3 track with its play order
Listening to FM and AM Broadcasts (see page 5)
• If the System takes time to show the Radio Data System
information—PS, PTY, RT signals,“PS,”“PTY,”or“RT”will
appear while searching.
Connecting a Portable Audio Device (see page 6)
Playing back a portable audio device:
• If a component connected to the LINE IN jack is not loud
enough, QP Link may not work properly.
In such cases, adjust the volume level of the component
louder so that the System can detect the sound signal
properly.
• Changing from“LINE”to another source while QP Link
works will deactivate QP Link temporarily.
In this case, the following reactivates QP Link:
– Pressing QP LINK on the remote control.
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off
• If you press button to turn the System off or if preset
Timer turns the System off while QP Link works, the System
deactivates QP Link temporarily.
In such cases, the following reactivates QP Link:
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off
– When you turn on the power again
Setting the Clock and Daily Timer (see left)
• “0:00”will flash on the display until you set the clock.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, readjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
• If you do not specify the preset station correctly while
setting a timer, the currently selected station will be played
when the timer is activated.
• When the on-time of the daily timer comes, the System
sets the volume level gradually to the preset level after
about 5 seconds.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing
the selected source, Daily Timer is canceled.
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
– NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.;
– NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
Listening to FM and AM Broadcasts
NOTE
If an external device is not equipped with a stereo mini plug audio output, use a plug adaptor to convert the stereo mini plug
to the corresponding plug of the audio output.
Playing back a portable audio device
Portable audio device
(Digital Audio Player, etc.)
To audio output
(or headphone out, etc.)
Recording to a portable audio device
Portable audio device equipped with the audio input
(Digital Audio Player, etc.) To audio input

Question & answers

There are no questions about the JVC UX-N1 yet.

Ask a question about the JVC UX-N1

Have a question about the JVC UX-N1 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC UX-N1. Please make sure that you describe your difficulty with the JVC UX-N1 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.