JVC UX-GN6 manual

View a manual of the JVC UX-GN6 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: JVC
  • Product: Hi-Fi system
  • Model/name: UX-GN6
  • Filetype: PDF
  • Available languages: English, German

Table of Contents

Page: 0
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the
areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate
air path for ventilation by placing on a stand with a height
of 10 cm or more.
ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou
d’incendie et éviter toute détérioration, installez l’appareil de
la manière suivante:
1. Avant: Bien dégagé de tout objet.
2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque
les espaces indiqués sur le schéma ci-dessous.
3. Dessous: Posez l’appareil sur une surface plane et
horizontale. Veillez à ce que sa ventilation correcte puisse
se faire en le plaçant sur un support d’au moins dix
centimètres de hauteur.
Connections For iPod
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not work.
INSTRUCTIONS
LVT1989-001B[J/C]
0209RYMMDWDAT
©2009 Victor Company of Japan, Limited
1
2 4
Basic and Common Operations
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN6J (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
• Video cord (× 1)
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
When you use the remote control for the first time, pull out
the insulation sheet.
To Replace the Battery in the Remote Control
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Basic Disc/USB Mass Storage Class Device Operations
To Press Indication/Result
Play back the disc • During playback, press again to pause.
Play back the USB
mass storage class
device
Stop playback • While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group
(MP3/WMA only)
Select the next groups.
Select the previous groups.
Forward search/
Reverse search
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
Change
the display
information
(only for USB)
Press repeatedly.
NOTES:
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
Playing Repeatedly—Repeat Play
1 Press repeatedly to specify the repeat mode as follows:
RPT TRK: Repeats the current (or specified) track. [ 1]
RPT GRP: Repeats all tracks in the current group (MP3/WMA
only). [ ]
RPT ALL: Repeats all tracks. [ ALL]
RPT OFF: Normal playback
2 or
Getting Started Playing Back a Disc/USB Mass Storage Class Device
MICRO COMPONENT SYSTEM
UX-GN6
—Consists of CA-UXGN6 and SP-UXGN5
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Loading a Disc
1 Touch to open the disc tray.
2 • When using an 8 cm (3 3/16 inch) disc, place it on
the inner circle of the disc tray.
3 Touch to close the disc tray.
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
NOTES:
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m (3.3 ft).
• USB mass storage class device is charged through the USB terminal when the System
is turned on and the source is “USB.”
• You cannot connect a computer to the USB terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB terminal may
not be fully inserted into the USB terminal on the System. In such a case, use a USB
extension cable (not supplied) to connect.
Prohibiting Disc Ejection (on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same
procedure.
3
Programming the Playing Order—Program Play
(only for Disc)
1 Select disc as the source.
2 Activate the Program Play.
3
or
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
4 Press to store the selected track.
5 Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
6 The program is completed and the tracks are
played back in the programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or ¢.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from Program Play, press 7.
– The stored program is kept.
Playing at Random—Random Play (only for Disc)
1 Select disc as the source.
2 Press repeatedly to select the desired Random Mode.
RND ALL: Plays all tracks in random order. [ALL RND]
RND GRP: Plays tracks in the current group in random
order. (MP3/WMA only). [RND]
RND OFF: Normal playback
3 Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
Thank you for purchasing a JVC product.
To
Press
Indication/Result
Main
unit
Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
See “Listening to an iPod/Viewing Images on the iPod”
on page 5.
Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as
the source.
• See “Listening to FM and AM Broadcasts” or “Listening
to Other Equipment” on page 5.
Adjust the volume
—
Drop the volume in
a moment —
To restore the volume, press again, or adjust the
volume level.
Select the Sound
Mode
—
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
Emphasize the
sound (Sound
Turbo)
The S.TURBO indicator lights up.
To cancel this function, press again.
Reinforce the bass
sound (Hyper Bass
Sound) —
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Change the display
brightness
Press repeatedly when the System is turned on.
Turn off the display
while on standby
Press repeatedly while the System is on standby.
Clock
DISP OFF:
ECO ON:
Turns off the display with the motion sensor
on.
Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
Rear view
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
NOTES:
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
Do not connect the AC power cord until all other connections have been made.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector.
Press and hold
Insert
Release
Red
Black
From left
speaker
From right
speaker
LVT1989-001B EN_UX-GN6[JC]
USB cable (not
supplied)
or
USB memory
(not supplied)
STANDBY lamp
Stereo mini plug cord
PHONES jack
Touch to turn on the System.
To use 4/¢ To use VOL +/–
To a wall outlet
Plug the AC power cord only after all
connections are complete.
CA-UXGN6 CA-UXGN6
Turn the AM loop antenna until
the best reception is obtained.
To connect the AM loop antenna
To assemble the AM loop antenna (supplied)
Red
Black
To connect the speaker cords
For customer use:
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
Warnings, Cautions and Others
Mises en garde, précautions et indications
diverses
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Le symbole de l’éclair à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur
la présence d’une “tension dangereuse” non
isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution
de personnes.
Le point d’exclamation à l’intérieur d’un
triangle équilatéral est destiné à alerter
l’utilisateur sur la présence d’opérations
d’entretien importantes au sujet desquelles
des renseignements se trouvent dans le
manuel d’instructions.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni
le coffret de l’appareil. Il n’y a aucune pièce réparable
par l’utilisateur à l’intérieur de l’appareil; confiez toute
réparation à un personnel qualifié.
3. ATTENTION: Rayonnement laser visible et/ou invisible
de classe 1M une fois ouvert. Ne pas regarder directement
dans le faisceau avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.
CAUTION:
Changes or modifications not approved by JVC could void
the user’s authority to operate the equipment.
[European Union only]
[Union européenne seulement]
CAUTION
The button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION
La touche , quelle que soit sa position, ne coupe pas la
ligne principale.
Débrancher la fiche principale pour couper complètement
l’alimentation du secteur (le témoin STANDBY s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif
de déconnexion de l’appareil, et l’appareil déconnecté doit
être prêt à être utilisé.
• Quand l’appareil est en mode d’attente, le témoin STANDBY
est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être commandée à distance.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which
contains Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Remote sensor
CAUTION: Excessive sound pressure from earphones or
headphones can cause hearing loss.
ATTENTION: Une pression acoustique excessive des écouteurs
ou du casque d’écoute peut entraîner une perte auditive.
Lithium coin battery
(product number: CR2025)
Insulation sheet
To connect the monitor
(not supplied)
—To view video/picture
from the iPod
SP-UXGN5
CAUTION: Battery shall not be exposed to excessive heat
such as sunshine, fire, or the like.
ATTENTION: Les piles ne doivent en aucun cas être
exposées à une chaleur excessive (lumière du solei, feu,
etc.).
SP-UXGN5
Point at the remote sensor on the front panel.
Headphones
(not supplied)
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Monitor
Video cord
(supplied)
The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
(canceled)
AM loop antenna
(supplied)
(canceled)
ATTENTION:
• Ne bloquez pas les orifices ou les trous de ventilation. (Si
les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une
bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut
des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un
égouttement ou à des éclaboussures et ne placez pas des
objets remplis de liquide, tels qu’un vase, sur l’appareil.
Front/Face Side/Côté
Page: 1
Connecting an iPod
To detach the dock adapter from the dock:
Pull up the dock adapter with your fingernail or sharp
pointed tool using the slot.
• Be careful not to injure your fingertips or damage the
terminal of the dock.
• Be sure to reduce the volume on the System to the minimum level before
connecting an iPod. Adjust the volume after starting playback.
• DO NOT connect or disconnect the iPod when the System is turned on.
• You cannot send any data to your iPod from the System.
• Do not carry the System with iPod connected. You might drop the iPod or it
might cause damages to the iPod dock.
• Do not touch or hit the iPod terminal pins or connector pins in the iPod dock
directly. It might cause damages to the connector part.
• Before viewing a video/picture from your iPod on your monitor, make the
appropriate video setting on the iPod. For details of the setting, refer to the
instruction manual for the iPod.
Basic iPod Operations
To Press Indication/Result
Play back an iPod The System detects the iPod and starts
playback.
Select a track Select the next tracks.
To go back to the beginning of the current
or previous tracks.
Forward search/
Reverse search
Press and hold to fast-forward the track
during playback.
Press and hold to fast-reverse the track
during playback.
5 7
6 8
Troubleshooting
Maintenance
To get the best performance of the System, keep your discs and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge while pressing the center
hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe
it with a cloth soaked in water-diluted neutral detergent and wrung well, then
wipe clean with a dry cloth.
• Since the System may deteriorate in quality, become damaged or get its paint
peeled off, be careful about the following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact for a long time.
Specifications
Listening to Other Equipment
Learning More about This System
Listening to an iPod/Viewing Images on the iPod (see
page 5)
• Compatible iPod:
iPod model Audio Video
iPod nano 1GB/2GB/4GB –
iPod nano (2nd Generation)
2GB/4GB/8GB
–
iPod nano (3rd Generation) 4GB/8GB
iPod nano (4th Generation) 8GB/16GB
iPod mini 4GB/6GB –
iPod mini (2nd Generation) 4GB/6GB –
iPod (4th Generation) 20GB/40GB –
iPod classic 80GB/160GB
iPod photo (4th Generation)
20GB/30GB/40GB/60GB
iPod video (5th Generation)
30GB/60GB/80GB
iPod touch 8GB/16GB
iPod touch (2nd Generation) 8GB/16GB
• If incompatible iPod is connected, the iPod may not be
operated from the System.
• When an iPod is connected to the System, the battery in
the iPod is charged through the iPod terminal (except when
the ECO Mode is activated).
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion occurs,
it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction
manual.
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Listening to FM and AM Broadcasts
Amplifier section
OUTPUT POWER:
60 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no
more than 10% total harmonic distortion
Speakers/Impedance: 8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/50 kΩ (at“NORMAL”)
250 mV/50 kΩ (at“HIGH”)
Digital input: USB
Tuner section
FM tuning range: 87.5 MHz - 108.0 MHz
AM tuning range: 530 kHz - 1 710 kHz
Disc player section
Dynamic range: 80 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
USB storage
USB specification: Compatible with USB 2.0 Full Speed
Compatible device: Mass storage class
Compatible file system: FAT16, FAT32
Bus power supply: DC 5 V 500 mA
iPod section
iPod output power: DC 5 V 500 mA
VIDEO OUT: Composite
General
Power requirements: AC 120 V , 60 Hz
Power consumption: 36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
Dimensions (W x H x D): 165 mm x 250 mm x 272 mm
(6 1/2 inches x 9 7/8 inches x
10 3/4 inches)
Mass: 3.5 kg (7.8 lbs)
Speakers
Speaker units: 4 cm (1-5/8 inches) cone x 1
12 cm (4-3/4 inches) cone x 1
Impedance: 8 Ω
Dimensions (approx.): 140 mm x 250 mm x 183 mm
(W x H x D) (5 9/16 inches x 9 7/8 inches x
7 1/4 inches)
Mass (approx.): 1.8 kg (4.0 lbs) each
Specifications and appearance are subject to change without
prior notice.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
iPod Operations
The iPod does not play, but “CONNECT” appears on the
display.
\ The iPod battery is low or exhausted. Charge the iPod
battery.
The video/picture from the iPod is not displayed on the
monitor.
\ The video settings on the iPod is incorrect. Refer to the
instruction manual for the iPod.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
Playing Back a Disc/USB Mass Storage Class Device
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from the
one you have intended while recording. If a folder (group)
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management)
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
• Prohibiting disc ejection (or canceling it) is not available
when the display is turned off (“DISP OFF”) or the ECO Mode
is activated (“ECO ON”) (see page 3).
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Listening to an iPod/Viewing Images
on the iPod
Connector pins
Apple iPod (separately purchased)
Direct dock
for iPod
BT-51018-5
(0306)
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time,
remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the
power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may
cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a
new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the
wall outlet, then consult your dealer. Using the System in this state may cause a
fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C
(41˚F) and 35˚C (95˚F).
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the
System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug
the power cord and consult your dealer.
LVT1989-001B EN_UX-GN6[JC]
To Press Indication/Result
Display the menu/
Go back to the
previous menu
—
Select an item on
the menu
or
• The UP/DOWN buttons work
in the same way as operating
the click wheel of iPod
counterclockwise/clockwise.
(Refer to the instruction manual
for the iPod for details.)
Play back at
random
• Refer to the instruction manual for
the iPod for details.
Play back
repeatedly
• Refer to the instruction manual for
the iPod for details.
Change the display
information
Press repeatedly.
Display Information
Play mode indicators
(See page 4.)
Main display A.STBY (Auto Standby)
indicator (See page 6.)
HBS indicator
(See page 3.)
Timer mode indicators
(See page 6.)
SLEEP indicator (See page 6.)
File type indicators (See page 4.)
FM reception indicators
(See page 5.)
Source indicators
S.TURBO (Sound Turbo)
indicator (See page 3.) Source indicators
Setting the Clock
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press MENU/CANCEL.
1 Press to activate the clock setting mode.
AM 12:00
2 or
Adjust the hour, then the minute.
Setting the Sleep Timer
Press repeatedly to specify the time (in minutes) as follows:
The SLEEP indicator lights up and the display dims.
To check the remaining time until the System shuts off, press SLEEP once.
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB/iPod)
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System turns off.
To cancel this function, press the button again.
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of
the Daily Timers.
• To correct a misentry during the process, press MENU/CANCEL. You can return to
the previous step.
1 Press repeatedly to select one of the timer you want to
set—TIMER-1, TIMER-2, or TIMER-3.
2
3
or
1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“DISC,” “USB HOST,”
“TUNER FM,” “TUNER AM,” “AUDIO IN,” or “IPOD.”
4 For “TUNER FM” or “TUNER AM”: Select a preset
channel.*
For “DISC” or “USB HOST”: Select a track. (For MP3/
WMA: Select the group, then the track number.)
5 Select the volume.
4 Turn off the System (on standby).
• When the on-time comes, the System starts playing
the specified source and sets the volume gradually
to the preset level.
* If no preset channel is stored, “NOMEMORY” appears. When the on time comes, the
System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
To Turn Off the Daily Timer
1 Press repeatedly to select “TIMER-1,” “TIMER-2,” or “TIMER-3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing
TIMER, then press SET.
Setting the Clock and Using Timers
Canceled
(canceled)
Basic Tuner Operations
To Press Indication/Result
Select FM or AM Press repeatedly to select “FM” or “AM.”
• The selected frequency band appears.
Select a frequency
or
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.
Tune in to a preset
station
• For presetting
stations, see the
right column.
or
Press repeatedly to select its preset number.
Change the FM
reception mode
(When an FM
stereo broadcast is
hard to receive)
Press to improve reception.
The (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again.
The (stereo) indicator lights up.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
1 Tune in to a station you want to preset.
• You can also store the FM reception mode.
2 Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display
is flashing.
3 Press to select a preset number for the station you want to
store.
4 Press to store the station.
or
Digital Audio Player, etc.
Stereo mini plug cord
(not supplied)
1 Turn the volume to minimum.
2 Press repeatedly to select “AUDIO IN.”
3 Start playing the connected equipment.
4 Adjust the volume.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO IN jack is too loud or too
quiet, you can change the audio input level through the AUDIO IN jack (without
changing the volume level).
Press repeatedly to select the level as follows:
NORMAL: Ordinary input level.
HIGH: Increases the input level.
Front view
To audio output (or
headphone out, etc.)
Insert the iPod directly to the connector pins.
SOUND indicator
(See page 3.)
Protective cap
Dock adapter
(supplied with
the iPod or sold
separately)

Question & answers

There are no questions about the JVC UX-GN6 yet.

Ask a question about the JVC UX-GN6

Have a question about the JVC UX-GN6 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC UX-GN6. Please make sure that you describe your difficulty with the JVC UX-GN6 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.