JVC TH-C50 manual

View a manual of the JVC TH-C50 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: JVC
  • Product: Home cinema set
  • Model/name: TH-C50
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 0
TH-C60
LVT1504-003B
[J]
TH-C40
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
TH-C50
INSTRUCTIONS
Consists of XV-THC60, SP-PWC60,
SP-THC60F, SP-THC60C and SP-THC60S
Consists of XV-THC50, SP-PWC50,
SP-THC60F, SP-THC60C and SP-THC50S
Consists of XV-THC40, SP-PWC40,
SP-THC40F, SP-THC40C and SP-THC40S
DVD DIGITAL THEATER SYSTEM
TH-C60-40[J]rev-4.book Page 1 Tuesday, April 18, 2006 2:16 PM
Page: 1
G-1
Warnings, Cautions and Others/Mises en garde, précautions et
indications diverses
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Section 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CAUTION
Changes or modifications not approved by JVC
could void the user’s authority to operate the
equipment.
ATTENTION
Des changements ou modifications non approuvés
par JVC pourront invalider l’autorité de l’utilisateur
à opérer cet appareil.
For Canada
THIS DIGITAL APPARATUS DOES NOT
EXCEED THE CLASS B LIMITS FOR RADIO
NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE
INTERFERENCE-CAUSING EQUIPMENT
STANDARD ENTITLED “DIGITAL
APPARATUS,” ICES-003 OF THE
DEPARTMENT OF COMMUNICATIONS.
Pour le Canada
CET APPAREIL NUMERIQUE RESPECTE LES
LIMITES DE BRUITS RADIOELECTRIQUES
APPLICABLES AUX APPAREILS NUMIRIQUES
DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR:
“APPAREILS NUMERIQUES”, NMB-003
EDICTEE PAR LE MINISTRE DES
COMMUNICATIONS.
CAUTION!
To avoid personal injury or
accidentally dropping the unit, have
two persons unpack, carry, and install
the unit.
ATTENTION!
Pour éviter toute blessure personnelle
ou toute chute accidentelle de
l’appareil, celui-ci doit être déballé,
transporté et installé par deux
personnes.
TH-C60: 39 kg/86 lbs
TH-C50: 33 kg/73 lbs
TH-C40: 24 kg/53 lbs
TH-C60: 39 kg/86 lbs
TH-C50: 33 kg/73 lbs
TH-C40: 24 kg/53 lbs
TH-C60-40[J]rev-4.book Page 1 Tuesday, April 18, 2006 2:16 PM
Page: 3
1
Introduction ....................................................2
Notes on handling ..................................................................... 2
Supplied accessories .................................................................. 2
About discs ......................................................3
Playable disc types ..................................................................... 3
Playable file types ....................................................................... 4
Description of parts and controls ..................5
Connections .....................................................8
Connecting the FM and AM antennas ................................... 8
Connecting the satellite (front, center, surround) speakers ......9
Speaker layout .......................................................................... 12
Connecting a TV ...................................................................... 12
Connecting the powered subwoofer ..................................... 13
Connecting to an analog component ................................... 13
Connecting to a digital component ...................................... 13
Connecting a USB mass storage class device ....................... 13
Connecting the power cord .................................................... 13
Operating external components with the
remote control ..............................................14
Operating the TV ..................................................................... 14
Operating the DBS tuner or CATV converter .................... 15
Operating the VCR .................................................................. 15
Basic operations ............................................16
Turning the system on/off ...................................................... 16
Selecting the source to play .................................................... 17
Adjusting the volume [VOLUME] ....................................... 17
Listening with headphones (not supplied) .......................... 17
Turning off the sound temporarily [MUTING] ................. 17
Adjusting the brightness of the indications [DIMMER] ... 17
Sleep Timer [SLEEP] ............................................................... 18
Adjusting the output level of the subwoofer and speakers ......18
Adjusting the sound ................................................................ 18
Changing the scan mode ........................................................ 18
Playback ........................................................ 19
Basic playback ...........................................................................19
One Touch Replay ...................................................................21
Fast-forward/fast-reverse search ............................................21
Skip to the beginning of a desired selection .........................22
Skipping at about 5-minute intervals ....................................22
Locating a desired title/group using number buttons ........22
Advanced operations ................................... 23
Using the surround mode .......................................................23
Using the on-screen bar ..........................................................25
Playing from a specified position on a disc ..........................26
Using the file control display ..................................................27
Resume Playback ......................................................................28
Selecting a view angle ..............................................................28
Selecting the subtitle ................................................................28
Selecting the audio ...................................................................29
Special picture playback ..........................................................29
Program Playback ....................................................................30
Random Playback ....................................................................31
Repeat Playback ........................................................................31
Tray lock ....................................................................................32
Sound and other settings .........................................................32
Setting DVD preferences ............................. 33
Using the setup menus ............................................................33
Menu description .....................................................................33
Tuner operations .......................................... 36
Manual tuning ..........................................................................36
Preset tuning .............................................................................37
Selecting the FM reception mode ..........................................37
Reducing the noise of AM broadcast ....................................37
AV COMPU LINK remote control system .... 38
References .................................................... 39
Maintenance .............................................................................39
Troubleshooting .......................................................................39
Specifications ............................................................................40
Table of contents
TH-C60-40[J]rev-4.book Page 1 Tuesday, April 18, 2006 2:16 PM
Page: 4
2
7 Important cautions
Installation of the system
• Select a place which is level, dry and neither too hot nor too cold;
between 5°C and 35°C (23°F and 95°F).
• Leave sufficient distance between the system and the TV.
• Do not use the system in a place subject to vibration.
Power cord
• Do not handle the power cord with wet hands.
• A small amount of power is always consumed while the power
cord is connected to the wall outlet (center unit only).
• When unplugging the power cord from the wall outlet, always
pull on the plug, not the power cord.
To prevent malfunctions of the system
• There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the system.
• Do not use any non-standard shape disc (like a heart, flower or
credit card, etc.) available on the market, because it may damage
the system.
• Do not use a disc with tape, stickers, or paste on it, because it may
damage the system.
Note about copyright laws
Check the copyright laws in your country before recording from the
discs. Recording of copyrighted material may infringe copyright
laws.
Note about copyguard system
The discs are protected by copyguard system. When you connect
the system to your VCR directly, the copyguard system activates and
the picture may not be played back correctly.
7 Safety precautions
Avoid moisture, water and dust
Do not place the system in moist or dusty places.
Avoid high temperatures
Do not expose the system to direct sunlight and do not place it near
a heating device.
When you are away
When away on travel or for other reasons for an extended period of
time, disconnect the power cord plugs from the wall outlet.
Do not block the vents
Blocking the vents may damage the system.
Care of the cabinet
When cleaning the system, use a soft cloth and follow the relevant
instructions on the use of chemically-coated cloths. Do not use
benzene, thinner or other organic solvents including disinfectants.
These may cause deformation or discoloring.
If water gets inside the system
Turn the system off and disconnect the power cord plug from the
wall outlet, then call the store where you made your purchase. Using
the system in this condition may cause a fire or electrical shock.
Check to be sure you have all of the supplied accessories.
The number in parentheses is the quantity of the pieces supplied.
If anything is missing, contact your dealer immediately.
• Remote control (1)
• Batteries (2)
• FM antenna (1)
• AM loop antenna (1)
• Power cord (1)
• System cord (1)
• Composite video cord (1)
• Speaker cords (for TH-C60/TH-C50)
4 m (13.2 ft): For satellite (front left/right) and center speakers (3)
10 m (32.8 ft): For satellite speakers (surround left/right) (2)
• Screws
TH-C60:
M5 x 40 mm (M5 x 1-5/8 inches) (4)
M4 x 20 mm (M4 x 13/16 inches) (8)
TH-C50:
M5 x 40 mm (M5 x 1-5/8 inches) (2)
M4 x 20 mm (M4 x 13/16 inches) (4)
• Speaker cord clamps
TH-C60 (4)
TH-C50 (2)
Notes on handling
Paste
Sticker
Label sticker
Supplied accessories
Introduction
TH-C60-40[J]rev-4.book Page 2 Tuesday, April 18, 2006 2:16 PM
Page: 5
3
This system has been designed to play back the following discs:
The √ in the list below shows available disc types and recording
formats.
*1
This system can play finalized discs only.
*2
Recorded with UDF Bridge format.
*3
This system may not be able to play back a file if the file size is
too large.
• It is possible to play back finalized +R/+RW (DVD Video Format
only) discs. “DVD” lights on the display panel when a +R/+RW
disc is loaded.
• This system accommodates the NTSC system, and also can play
discs recorded with PAL system. Note that an PAL video signal on
a disc is converted to the NTSC signal and output.
• The Non-DVD side of a “DualDisc” does not comply with the
“Compact Disc Digital Audio” standard. Therefore, the use of
Non-DVD side of a DualDisc on this product may not be
recommended.
• On some DVD VIDEOs, VCDs or SVCDs, their actual
operation may be different from what is explained in this
manual. This is due to the disc programming and disc
structure, not a malfunction of this system.
DVD Logo is a trademark of DVD Format/Logo Licensing
Corporation.
Notes on DVD-R and DVD-RW
• This system does not support “multi-border” disc.
• This system does not support a disc recorded with DVD VR
format.
Notes on CD-R and CD-RW
• This system can play CD-Rs or CD-RWs recorded with ISO 9660
format.
• This system supports “multi-session” discs (up to 12 sessions).
• This system cannot play “packet write” discs.
Region code of DVD VIDEO
DVD VIDEO players and DVD VIDEO discs have their own
Region Code numbers. This system can play back DVD VIDEO
discs whose Region Code numbers include the system's Region
Code, which is indicated on the rear panel.
If a DVD with an improper Region Code number is loaded,
“REGION CODE ERROR!” appears on the TV screen and playback
cannot start.
Some discs may not be played back because of their disc
characteristics, recording conditions, or damage or stain on them.
Playable disc types
DVD VIDEO Audio CD
VCD SVCD
Disc type
CD-R/-RW*1 DVD-R*1 DVD-RW*1
Recording
format
DVD Video — √ √
VCD/SVCD √ — —
Audio CD √ — —
MP3 √ √*2 √*2
WMA √ √*2
√*2
JPEG √*3
√*2
√*2
ASF √ √*2
√*2
MPEG-2 √*3
√*2
√*2
MPEG-1 √*3
√*2
√*2
DivX √ √*2
√*2
Unplayable discs
DVD-ROM, DVD-RAM, CD-I (CD-I Ready), Photo CD, SACD,
etc.
Playing back these discs will generate noise and damage the
speakers.
Example of playable DVD:
About discs
TH-C60-40[J]rev-4.book Page 3 Tuesday, April 18, 2006 2:16 PM
Page: 6
4
For all playable files
• The system can only recognize and play files with one of the
following extensions, which can be in any combination of upper
and lower case;
MP3: “.MP3”, “.mp3”
WMA: “.WMA”, “.wma”
JPEG: “.JPG”, “.JPEG”, “.jpg”, “.jpeg”
ASF: “.ASF”, “.asf”
MPEG-2/MPEG-1: “.MPG”, “.MPEG”, “.mpg”, “.mpeg”
DivX: “.DIVX”, “.DIV”, “.divx”, “.div”, and “.AVI”, “.avi”
• The system recognizes up to 150 tracks (files) per group, 99
groups per disc/device, and the total number of the tracks (files)
that the system can play is 4000.
• Some files may not be played back normally because of their disc
characteristics or recording conditions.
• MP3/WMA/JPEG/ASF/MPEG-2/MPEG-1/DivX files require a
longer readout time. (It differs due to the complexity of the
directory/file configuration.)
• If different kinds of files are mixed, set the FILE TYPE setting in
the PICTURE menu to the appropriate setting for the data to be
read (“AUDIO”, “STILL PICTURE” or “VIDEO”). (See page 34.)
For MP3/WMA files
• The system supports MP3/WMA files recorded with a bit rate of
32 – 320 kbps and a sampling frequency of 16 kHz, 22.05 kHz,
24 kHz*, 32 kHz, 44.1 kHz, or 48 kHz.
• If the track information (track title, artist, and album name, etc.)
is recorded, it appears in the file control display on the TV screen.
(See page 27.)
• We recommend to record each piece of material (song) at a
sample rate of 44.1 kHz and at a data transfer rate of
128 (96*) kbps.
* For WMA only
For JPEG files
• We recommend to record a file at 640 x 480 resolution. (If a file
has been recorded at a resolution of more than 640 x 480, it will
take a longer time to be displayed.)
• This system can only play baseline JPEG files.
For ASF files
• The system supports the types of the advanced simple profile as
MPEG-4 files (MPEG-4 ASF).
• The system supports MPEG-4 files with the following conditions:
File format: ASF
Visual profile: MPEG-4 SP (Simple Profile)
Audio CODEC: G.726
Max. picture size: 352 x 288 (CIF)
Max. bit rate: 384 kbps
For MPEG-2/MPEG-1 files
• The stream format should conform to MPEG system/program
stream.
• 720 x 576 pixels (25 fps)/720 x 480 pixels (30 fps) is
recommended for the highest resolution.
• This system also supports the resolutions of 352 x 576/480 x 576/
352 x 288 pixels (25 fps) and 352 x 480/480 x 480/352 x 240 pixels
(30 fps).
• The file format should be MP@ML (Main Profile at Main Level)/
SP@ML (Simple Profile at Main Level)/MP@LL (Main Profile at
Low Level).
• Audio streams should conform to MPEG1 Audio Layer-2 or
MPEG2 Audio Layer-2.
For DivX files
• The system supports DivX 6.x, 5.x, 4.x and 3.11.
• The system supports DivX files whose resolution is 720 x 480
pixels or less (30 fps), and 720 x 576 pixels or less (25 fps).
• Audio stream should conform to Dolby Digital (including multi
channel) or MPEG1 Audio Layer-3 (MP3).
• The system does not support GMC (Global Motion
Compression).
• The file encoded in the interlaced scanning mode may not be
played back correctly.
• The system has its own Registration Code for DivX playback.
• If necessary, you can confirm the Registration Code of your
system using the OTHERS menu. (See page 35.)
Playable file types
• This product incorporates copyright protection technology that
is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized
by Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
• USE OF THIS PRODUCT IN ANY MANNER THAT
COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS
PROHIBITED, EXCEPT FOR USE BY A CONSUMER
ENGAGING IN PERSONAL AND NON-COMMERCIAL
ACTIVITIES.
• DivX, DivX Ultra Certified, and associated logos are trademarks
of DivX, Inc. and are used under license.
• Official DivX® Ultra Certified product
• Plays all versions of DivX®
video (including DivX®
6) with
enhanced playback of DivX® media files and the DivX® Media
Format
About discs
TH-C60-40[J]rev-4.book Page 4 Tuesday, April 18, 2006 2:16 PM
Page: 7
5
Front panel (center unit)
The numbers in the figures indicate the pages where the details of the parts are described.
Rear panel (center unit)
Display window
24 37 20 24
18
28
20
37 31, 32
Disc tray (inside): 19
20
20
21
19 19 19 21, 36 17
17
17
19
16 16
36
31
30
36
Remote sensor: 7
13
12
18
13
38
13
13 8
13
12 13
12 12
Description of parts and controls
TH-C60-40[J]rev-4.book Page 5 Tuesday, April 18, 2006 2:16 PM
Page: 8
6
Powered subwoofer
SP-PWC60/SP-PWC50
SP-PWC40
NOTE
• For safety reasons, always ensure that there is sufficient space behind
the powered subwoofer.
* Do not block the ventilation openings to allow proper air
circulation by the cooling fan.
Front Rear
POWER ON
lamp: 16
11
Power cord: 13
13
Front Rear
POWER ON
lamp: 16
11
Power cord: 13
13
Description of parts and controls
TH-C60-40[J]rev-4.book Page 6 Tuesday, April 18, 2006 2:16 PM
Page: 9
7
Remote control Putting batteries in the remote control
If the range or effectiveness of the remote control decreases, replace
both batteries.
CAUTION
• Do not expose batteries to heat or flame.
Operating the system from the remote control
Aim the remote control directly to the front panel of the center unit.
• Do not block the remote sensor.
14, 17
14, 15
19, 37
18 - 37
22
29
33
28
32
17
25 - 32
Number
buttons: 22
18
28, 29
24
18
26
17
19
31
20
14
22, 36
16
15
19
14 - 36
21, 29
19, 37
26
14
26
15, 21
18
18, 30
30, 31
30
17
18
19, 29
R03 (UM-4)/AAA (24F) type dry-cell
batteries (supplied)
Description of parts and controls
TH-C60-40[J]rev-4.book Page 7 Tuesday, April 18, 2006 2:16 PM
Page: 10
8
7 AM loop antenna
Setting up supplied AM loop antenna
Connecting AM loop antenna
• Turn the loop antenna until you have the best reception during
AM broadcast program reception.
NOTE
• Make sure the antenna conductors do not touch any other terminals,
connecting cords or power cords. This could cause poor reception.
If reception is poor
7 FM antenna
If reception is poor
NOTE
• We recommend that you use coaxial cable for the FM antenna as it is
well-shielded against interference.
Connecting the FM and AM
antennas
If the antenna cord is covered with the insulation
coat, twist and pull the insulation coat off and
remove.
1
Center unit
2
3
Antenna cord
Outdoor single vinyl-covered wire antenna
(not supplied)
AM loop antenna
Center unit
Extend the supplied FM antenna
horizontally.
Center unit
FM antenna (supplied)
Outdoor FM antenna (not
supplied)
Outdoor FM antenna cord (not
supplied)
Center unit
Standard type (75 Ω
coaxial) connector
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]rev-4.book Page 8 Tuesday, April 18, 2006 2:16 PM
Page: 11
9
7 Assembling the speakers — TH-C60/TH-C50
7 For TH-C60: Assemble front speakers and surround speakers.
7 For TH-C50: Assemble front speakers.
For the surround speakers of TH-C50, see “Connecting the
surround speakers — TH-C50”. (See page 10.)
For TH-C60
• Check the model name of each speaker from the label on the
rear to locate each speaker correctly.
For TH-C50
Before assembling —
• Prepare a Phillips screwdriver (not supplied).
• Take care not to drop any component part while assembling;
otherwise, it may cause damage to the floor or injury.
Connecting the satellite (front,
center, surround) speakers
Assembled speakers
With stand: Refer to steps 1 to
3.
Without stand: Refer to steps
2 and 3.
Front speaker
(SP-THC60F) (2)
Base plate (4)
Surround
speaker
(SP-THC60S) (2)
Stand (4)
Front speaker
(SP-THC60F)(2)
Base plate (2)
Stand (2)
or
Speaker
Screw M5 x 40 mm/M5 x 1-5/8
inches (supplied)
1
Stand
2 When assembling a speaker without stand:
Speaker
Stand (or speaker
directly)*
Base plate
ScrewM4x20mm/M4
x 13/16 inches
(supplied)*
A: Use these screws (M4 x
45 mm/M4 x 1-13/16 inches)
when assembling the speaker
with the base plate.
* When assembling the speaker with the base plate, use the
screws A.
Black
Red White
Black
3
You can route the speaker cord
by using speaker cord clamp
(supplied).
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]rev-4.book Page 9 Tuesday, April 18, 2006 2:16 PM
Page: 12
10
7 Connecting the surround speakers — TH-C50 7 Connecting the center speaker — TH-C60/TH-C50
Surround speaker (SP-THC50S) (2)
Speaker
(bottom)
1
Red White
Black Black
2
For TH-C40, the front, surround and center speakers are
equipped with their speaker cords attached directly to their
speaker unit instead of having speaker terminals on their cabinet.
Center speaker (SP-THC60C) (1)
Red White
Black Black
Center speaker
(SP-THC40C)
Surround speaker
(SP-THC40S)
Front speaker
(SP-THC40F)
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]rev-4.book Page 10 Tuesday, April 18, 2006 2:16 PM
Page: 13
11
7 Connecting the satellite speakers to the subwoofer
Note that the illustration below is for SP-PWC60.
CAUTION
• If you connect speakers other than the supplied ones, use speakers of
the same speaker impedance (SPEAKER IMPEDANCE) indicated
near the speaker terminals on the rear of the powered subwoofer.
• DO NOT connect more than one speaker to one speaker terminal.
• When installing the satellite speakers on the wall;
– Be sure to have them installed on the wall by qualified personnel.
DO NOT install the satellite speakers on the wall by yourself to
avoid unexpected damage from falling off the wall due to incorrect
installation or weakness in wall structure.
– Care must be taken in selecting a location for speaker installation
on a wall. Injury to personnel or damage to equipment may result
if the speakers installed interfere with daily activities.
Precautions for daily use
• When moving the speakers, do not pull the speaker cords;
otherwise, the speakers may fall over, causing damage or injury.
• Do not reproduce sounds at so high a volume that the sound is
distorted; otherwise, the speakers may be damaged by internal
heat buildup.
For TH-C60/TH-C50:
• When holding a speaker, always grasp the lower portion.
• Do not lean against the speakers, as the speakers could fall down
or break, possibly causing an injury. Especially be careful that
children do not lean against them.
• Connect the black cords to the black (r) terminals.
• Connect the white cords to the (q) terminals
referring to the table below:
Speaker cord
FRONT SPEAKERS (LEFT) White
FRONT SPEAKERS (RIGHT) Red
CENTER SPEAKER Green
SURROUND SPEAKERS (LEFT) Blue
SURROUND SPEAKERS (RIGHT) Gray
Before connecting the speaker cords;
Twist and pull the insulation coat off and remove.
Powered subwoofer
TH-C60: SP-PWC60
TH-C50: SP-PWC50
TH-C40: SP-PWC40
Front speakers
TH-C60: SP-THC60F
TH-C50: SP-THC60F
TH-C40: SP-THC40F
Surround speakers
TH-C60: SP-THC60S
TH-C50: SP-THC50S
TH-C40: SP-THC40S
Center speaker
TH-C60: SP-THC60C
TH-C50: SP-THC60C
TH-C40: SP-THC40C
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]rev-4.book Page 11 Tuesday, April 18, 2006 2:16 PM
Page: 14
12
To obtain the best possible sound from this system, you need to
place all the speakers except the subwoofer at the same distance
from the listening position.
If your speakers cannot be placed at the same distance from the
listening position
You can adjust the delay time of the speakers. See “Delay menu
(DELAY)” on page 35.
NOTE
• Place the satellite speakers on a flat and level surface.
• The front and center speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, they may cause
color distortions. So, pay attention to the following when installing
the speakers.
– When placing the speakers near a TV set, turn off the TV’s main
power switch or unplug it before installing the speakers. Then wait
at least 30 minutes before turning on the TV’s main power switch
again.
Some TVs may still be affected even though you have followed the
above. If this happens, move the speakers away from the TV.
• The surround speakers are not magnetically shielded.
If they are located nearby the TV or monitor, it will probably cause
color distortion on the screen. To avoid this, do not place the speakers
nearby the TV or monitor.
• Be sure to place the powered subwoofer to the TV’s right. If you place
the powered subwoofer to the TV’s left, keep sufficient distance
between them to prevent the TV screen from appearing mottled.
• Distortion of picture may occur when connecting to the TV via a
VCR, or to a TV with a built-in VCR.
• You need to set “MONITOR TYPE” in the PICTURE menu
correctly according to the aspect ratio of your TV. (See page 34.)
7 To connect a TV equipped with the HDMI terminal
HDMI connection allows you to enjoy high quality picture on your
HDMI equipped TV with high-definition digital video signals.
• You can select the type of video signal from 480p, 1080i, or 720p.
(See page 18.)
NOTE
• This system outputs the signal to HDMI MONITOR OUT terminal
only when the source is DVD or USB MEMORY.
• This system outputs the audio signal of 48 kHz, 44.1 kHz, or 32 kHz
Linear PCM from HDMI MONITOR OUT terminal. To activate or
deactivate the audio signal output from HDMI MONITOR OUT
terminal, see page 34.
• HDMI indicator lights on the display window when the system and
the TV recognize each other and are ready to send and receive signals.
• When you enjoy HDCP contents, sound and picture may not be
transmitted to the speakers and TV for a few seconds in the beginning
for confirmation.
7 To connect a TV equipped with the component video input
jacks
• With analog video connection, you can get better picture quality
in the order — Component video > S-video > Composite video.
• If your TV supports progressive video input, you can enjoy a high
quality picture by setting the progressive scan mode to active.
(See page 18.)
NOTE
• While playing back DivX/ASF files, this system outputs only
progressive signals from the component video jacks. When your TV
does not support progressive video input, connect the TV through S-
video or composite video jack.
• If the component video input jacks of your TV are of the BNC type,
use a plug adapter (not supplied) to convert the pin plugs to BNC
plugs.
• The component video signals can be output only when you select
DVD or USB MEMORY as the source to play. (See page 17.)
7 ToconnectaTVequippedwiththecompositeorS-videojacks
Speaker layout
Connecting a TV
Front right
speaker
Center speaker
Powered
subwoofer
Surround left
speaker
Surround right
speaker
Front left
speaker
HDMI cable (not supplied)
To HDMI input
TV
Center unit
What is HDMI?
The HDMI (High Definition Multimedia Interface) is the
standard interface for the next-generation TV. By connecting this
system and a TV with the HDMI cable, digital video signals and
audio signals are transmitted through the cable. You can enjoy
digital video and sound without AD/DA conversion with easy
connection.
In addition, this system is compatible with HDCP (High-
Bandwidth Digital Content Protection), and HDCP contents can
be viewed if you connect a HDCP compatible TV to this system.
Center unit
To component
video input
TV
Component video cord (not supplied)
Composite video cord (supplied)
To composite
video input
S-video cord
(not supplied)
TV
To S-video input
Center unit
or
Align the 5 marks.
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]-03Body.fm Page 12 Wednesday, April 19, 2006 7:02 PM
Page: 15
13
You can enjoy the sound of an analog component.
NOTE
• The signals input to the VIDEO jack of the VCR IN jacks will be
output only from the VIDEO jack of the VIDEO OUT jacks, not from
the S-VIDEO jack of the VIDEO OUT jacks.
You can enjoy the sound of a digital component.
* DBS = Direct Broadcasting Satellite
NOTE
• Only digital audio signals can be input when selecting “DBS” as the
source to play. (See page 17.) When connecting a video component
such as a DBS tuner, operate this system to listen to the sound.
You can connect a USB mass storage class device such as a USB
flash memory device, hard disc drive, multimedia card reader,
digital camera, etc. to this system.
• After connecting a USB mass storage class device to this system
and selecting USB MEMORY as the source, the file control
display appears on the TV screen. (See page 27.)
NOTE
• When connecting a USB mass storage class device, refer also to its
manual.
• Connect one USB mass storage class device to the system at a time. Do
not use a USB hub.
• You cannot charge the USB mass storage class device while
connecting it to the USB MEMORY jack.
• While playing back a file in a USB mass storage class device, do not
disconnect the device. It may cause a malfunction of both the system
and the device.
• JVC bears no responsibility for any loss of data in the USB mass
storage class device while using this system.
• When connecting with a USB cable, use a cable less than 1 m (3.3 ft)
in length.
• This system is compatible with the USB 2.0 Full-Speed (not
compatible with the USB 1.1).
• You can play back the following types of files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps):
– Music: MP3, WMA
– Picture: JPEG
– Movie: MPEG-4 (ASF), DivX (maximum frame rate of 30 fps for
progressive)
• You cannot play back a file larger than 2 GB.
• When playing a file which has a large transfer rate, frames or sounds
may be dropped during playback.
• This system cannot recognize a USB mass storage class device whose
rating exceeds 5 V/500 mA.
• Some USB mass storage class devices may not be recognized or may
not work properly.
• This system may not play back some files even though their formats
are listed above.
.
Make sure that all other connections have been completed.
CAUTION
• Disconnect the power cord before cleaning or moving the system.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp and pull the plug so as not to damage the cord.
Connecting the powered
subwoofer
Connecting to an analog
component
Connecting to a digital
component
Powered
subwoofer
System cord
(supplied)
Center unit
Align the 5 marks. Align the 5 marks.
RCA pin plug
cord
(not supplied)
1 To composite video output
2 To S-video output
3 To audio output
1 2 3
Center unit
VCR (1 3 or 2 3)
TV (3)
Cassette recorder (3)
Composite video
cord
(not supplied)
S-video cord
(not supplied)
or
Digital optical cord (not supplied)
To digital optical output
DBS* tuner
MD player
Center unit
Connecting a USB mass storage
class device
Connecting the power cord
Center unit (on the
front panel
USB cable (not supplied)
Center unit Powered
subwoofer
Power cord
(Supplied) Power cord
Plug into AC outlets.
Connections Do not connect the power cord until all other connections have been made.
TH-C60-40[J]rev-4.book Page 13 Tuesday, April 18, 2006 2:16 PM
Page: 16
14
NOTE
• Manufacturers’ codes are subject to change without notice.
• Set the codes again after replacing the batteries of the remote control.
7 To set the manufacturer’s code
1 Slide the remote control mode selector
to TV.
2 Press and hold F TV.
Keep the button pressed until step 4 is finished.
3 Press ENTER.
4 Press number buttons (1-9, 0) to enter
the manufacturer’s code (2 digits).
Examples:
For a Hitachi TV: Press 1, then 0.
For a Toshiba TV: Press 0, then 8.
* “01” is the initial setting.
5 Release F TV.
If there is more than one code listed for corresponding brand,
try each one until you enter the correct one.
7 Operation
Aim the remote control at the TV.
IMPORTANT
Before using the remote control to operate a TV;
• Set the remote control mode selector to TV.
The following buttons are available:
F TV: Turns TV on and off.
TV VOL +/–: Adjusts the volume.
TV/VIDEO: Selects the input mode (either TV or
VIDEO).
CH +/–: Changes the channels.
1-10, 0, h10 (100+): Selects the channel.
TV RETURN: Alternates between the previously selected
channel and the current channel.
NOTE
• The operating buttons may differ depending on manufacturers.
The buttons described below are used on pages 14 and 15.
Remote
control mode
selector
Number
buttons
(play button)
Operating the TV
Manufacturer Code Manufacturer Code
JVC 01* Samsung 12
Hitachi 10 Sanyo 13, 14
Magnavox 02 Sharp 06
Mitsubishi 03 Sony 07
Panasonic 04, 11 Toshiba 08
Philips 15 Zenith 09
RCA 05
Operating external components with the remote control
TH-C60-40[J]rev-4.book Page 14 Tuesday, April 18, 2006 2:16 PM
Page: 17
15
7 To set the manufacturer’s code
1 Slide the remote control mode selector
to VCR/DBS.
2 Press DBS.
3 Press and hold F VCR/DBS.
Keep the button pressed until step 5 is finished.
4 Press ENTER.
5 Press number buttons (1-9, 0) to enter
the manufacturer’s code (2 digits).
Examples:
For a GI Jerrold product: Press 0, then 1.
For a Sony product: Press 2, then 0.
* “01” is the initial setting.
6 Release F VCR/DBS.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
7 Operation
Aim the remote control at the DBS tuner or CATV converter.
IMPORTANT
Before using the remote control to
operate a DBS tuner or CATV converter;
1 Set the remote control mode selector
to VCR/DBS.
2 Press DBS.
The following buttons are available:
F VCR/DBS: Turns DBS tuner or CATV converter on and
off.
CH +/–: Changes the channels.
1-10, 0, h10 (100+): Selects the channel.
7 To set the manufacturer’s code
1 Slide the remote control mode selector
to VCR/DBS.
2 Press VCR.
3 Press and hold F VCR/DBS.
Keep the button pressed until step 5 is finished.
4 Press ENTER.
5 Press number buttons (1-9, 0) to enter
the manufacturer’s code (2 digits).
Examples:
For a Philips VCR: Press 0, then 9.
For an NEC VCR: Press 2, then 5.
* “01” is the initial setting.
6 Release F VCR/DBS.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
7 Operation
Aim the remote control at the VCR.
IMPORTANT
Before using the remote control to
operate a VCR;
1 Set the remote control mode selector
to VCR/DBS.
2 Press VCR.
The following buttons are available:
F VCR/DBS: Turns VCR on and off.
3 (play button): Starts playback.
7: Stops operation.
8: Pauses playback.
y: Fast forwards video tape.
1: Rewinds video tape.
REC: Press this button together with 3 (play
button) to start recording or together with 8
to pause recording.
CH +/–: Changes the TV channels on the VCR.
NOTE
• When operating a VCR or DBS tuner/CATV converter;
– The source setting of VCR or DBS remains after you have changed
the remote control mode selector to AUDIO or TV. When operating
VCR or DBS tuner/CATV converter again, it is not necessary to
press VCR or DBS after setting the remote control mode selector.
Operating the DBS tuner or
CATV converter
Manufacturer Code
Echostar 21
GI Jerrold 01*, 02, 03, 04, 05, 06, 07, 08
Hamlin 15, 16, 17, 18
Pioneer 13, 14
RCA 19
Scientific Atlanta 09, 10
Sony 20
Zenith 11, 12
Operating the VCR
Manufacturer Code Manufacturer Code
JVC 01*, 02, 03 Philips 09
Emerson 11, 26 RCA 05, 06
Fisher 29 Samsung 24
Funai 10, 14, 15, 16 Sanyo 21, 22, 23
Gold Star 12 Sharp 27, 28
Hitachi 04 Shintom 30
Mitsubishi 13 Sony 18, 19, 20
NEC 25 Zenith 08
Panasonic 07, 17
Operating external components with the remote control See page 14 for button locations.
TH-C60-40[J]rev-4.book Page 15 Tuesday, April 18, 2006 2:16 PM
Page: 18
16
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
On the remote control:
Press FAUDIO.
On the center unit:
Press F.
When DVD or USB MEMORY is selected as the source (see page
17), the following messages will appear on the TV screen.
NOTE
• The STANDBY lamp on the center unit lights red when the power is
turned off. The lamp goes off when the power is turned on.
• The power supply to the subwoofer is linked to the center unit. The
POWER ON lamp on the subwoofer lights green when the power is
turned on.
• A small amount of power is consumed even when the power is turned
off (center unit only). This is called standby mode and the STANDBY
lamp lights in this mode. Unplug the power cord from the AC outlet
to turn the power off completely.
• You can also turn on the system by pressing the following buttons;
– One of the DISC (1-5) buttons (with SHIFT pressed) on the remote
control
– One of the DISC (1-5) 0 buttons on the center unit
– One of the source selecting buttons or 3 (play button) on the
remote control
– One of the DISC (1-5) 3 buttons or 3 on the center unit.
• When connecting your TV through HDMI MONITOR OUT
terminal, turn on the TV before turning on the system; otherwise, the
following phenomena may happen depending on the TV.
– The scan mode setting (see page 18) is changed.
– The sound comes out from the speakers on TV even though
“HDMI AUDIO OUT” in the AUDIO menu (see page 34) is set to
“OFF”.
If the above phenomena happen, turn off the system and turn it back
on, then set the scan mode again.
The buttons on the remote control are used to explain most of the
operations in this manual. You can use the buttons on the center
unit same as on the remote control for operations unless
otherwise noted.
The buttons described below are used on pages 16 to 18.
Source
selecting
buttons
Remote
control mode
selector
Cursor
(3/2)/
ENTER
(play button)
STANDBY lamp
Turning the system on/off
• “OPEN”/“CLOSE”:
Appears when opening or closing the disc tray.
• “NOW READING”
Appears when the system is reading the disc/file information.
• “REGION CODE ERROR!”:
Appears when the Region Code of the DVD VIDEO does not
match the code the system supports. The disc cannot be
played back.
• “NO DISC”:
Appears when no disc is loaded.
• “NO USB DEVICE”:
Appears when no USB mass storage class device is connected.
• “CANNOT PLAY THIS DISC”:
Appears when unplayable disc is loaded.
• “CANNOT PLAY THIS DEVICE”:
Appears when unplayable USB mass storage class device is
connected.
Basic operations
TH-C60-40[J]rev-4.book Page 16 Tuesday, April 18, 2006 2:16 PM
Page: 19
17
On the remote control:
Press one of the source selecting buttons
(DVD, USBMEMORY, FM/AM, VCR or DBS).
DVD:
To play back a disc (DVD VIDEO, VCD etc.). (See page 19.)
USB MEMORY:
To select a file in a USB mass storage class device. (See “To play a file
in a USB mass storage class device” on page 19.)
FM/AM:
To tune in an FM or AM station. (See page 36.) Each time you press
the button, the band alternates between FM and AM.
VCR:
To select the source from a component connected to the VCR IN
jacks and AUX IN (VCR) jacks. (See page 13.)
DBS:
To select the source from a component connected to the DIGITAL
IN (DBS) jack. (See page 13.)
On the center unit:
Press SOURCE repeatedly until the source
name you want appears on the display
window.
NOTE
• When AM, FM or DBS is selected, this system does not output video
signals.
• It may take time to change the source.
CAUTION
• Always set the volume to minimum level before starting any source.
If the volume is set at a high level, the sudden blast of sound could
permanently damage your hearing and/or blow out the speakers.
On the remote control:
Press VOL +/–.
On the center unit:
Turn VOLUME.
• To increase the volume, turn VOLUME clockwise.
• To decrease the volume, turn VOLUME counterclockwise.
CAUTION
Be sure to turn down the volume;
• Before connecting or putting on headphones as high volume may
damage both the headphones and your hearing.
• Before disconnecting headphones as high volume may be suddenly
output from the speakers.
While connecting a pair of headphones to the PHONES jack on the
center unit, the system automatically cancels the surround mode
(see page 23) currently selected, deactivates the speakers, turns the
subwoofer’s power off, and activates the headphone mode.
“H. PHONE” appears on the display window.
Headphone mode
When using the headphones, the following signals are output
regardless of your speaker setting;
• For 2 channel sources, the front left and right channel signals are
output from the headphones.
• Multi-channel signals are down-mixed and output from the
headphones.
Press MUTING.
To restore the sound
Perform one of the following:
• Press MUTING again.
• Press VOL +/– (or turn VOLUME on the center unit).
Press DIMMER.
Each time you press the button, you can change the brightness level
in 3 steps.
Selecting the source to play
Adjusting the volume
[VOLUME]
Listening with headphones
(not supplied)
Turning off the sound
temporarily [MUTING]
Adjusting the brightness of the
indications [DIMMER]
Basic operations See page 16 for button locations.
TH-C60-40[J]rev-4.book Page 17 Tuesday, April 18, 2006 2:16 PM
Page: 20
18
The system turns off automatically when the specified period of
time has passed.
Press SLEEP.
Each time you press the button, the shut-off time changes as
follows:
Example:
To check the remaining time
Press SLEEP once.
To change the remaining time
Press SLEEP repeatedly.
To cancel
Press SLEEP repeatedly until “SLEEP – –” appears.
• Turning off the power also cancels the Sleep Timer.
1 Press SPK LEVEL to show the target
speaker indication on the display
window.
Each time you press the button, the indication of the speakers
changes as follows:
2 Press LEVEL +/– to adjust the output
level from –6 to +6.
NOTE
• You can also make adjustments by using the setup menu shown on
the TV screen. (See page 35.)
• The adjustments take effect for all sources other than FM/AM. For
FM/AM, adjust the level separately by repeating the procedure above.
1 Press TREBLE/BASS to show “TRE” or
“BASS” on the display window.
Each time you press the button, the indication alternates
between “TRE” and “BASS”.
• TRE: Select this to adjust treble sound.
• BASS: Select this to adjust bass sound.
2 Press LEVEL +/– to adjust the level from
– 10 to +10 (in 2 steps).
NOTE
• The adjustments take effect for all sources.
The system can be accommodated to your TV’s scan mode.
NOTE
• To use the system in the progressive mode, it is required that the
center unit is connected to the TV by using an HDMI cable or a
component video cord (not supplied). (See page 12.)
7 While DVD or USB MEMORY is selected as the source and
stopped
1 Press and hold SCAN MODE for
2 seconds.
Currently selected scan mode appears on the display window.
2 Press Cursor 3/2 to select the desired
mode.
Each time you press the button, the scan mode changes as
follows:
7When connecting the TV with the component video cord:
7When connecting the TV with the HDMI cable:
• When selecting “AUTO”, the system outputs the video
signal to get the best picture quality on your TV according
to the High-Definition video signal compatibility of the
TV.
• When selecting “AUTO”, “1080i”, or “720p”, the system
up-convert the 480i or 480p signal to 1080i or 720p.
• When “1080i” or “720p” is selected, the HD indicator lights
on the display window.
• When selecting “1080i” or “720p”, this system does not
output video signals from component video, S-video, and
composite video jacks.
* 480i, 480p, 1080i, and 720p indicate the number of scanning
lines and scanning format of a video signal.
–480i/1080i indicates 480/1080 scanning lines with
interlaced format.
–480p/720p indicates 480/720 scanning lines with
progressive format.
• Generally, you can get better picture quality by selecting the
larger the number of scanning lines.
• You can get better picture quality in the progressive mode
than in the interlace mode.
3 Press ENTER while the selected mode is
displayed.
When the progressive mode is selected, the PROGRESSIVE
indicator lights on the display window.
NOTE
• When selecting “1080i”, the picture shrinks vertically.
• Changing the scan mode does not take effect when connecting the TV
with the S-video or the composite video cord.
• Although the picture may be distorted when you press ENTER, this is
not a malfunction of the system.
Sleep Timer [SLEEP]
– – (off) Z 10 Z 20 Z 30 Z 60 Z 90 Z 120 Z 150 Z
(back to the beginning) (Unit: min.)
Adjusting the output level of
the subwoofer and speakers
FRNT L (Front Left speaker) Z FRNT R (Front Right
speaker) Z CENTER (Center speaker) Z SURR L
(Surround Left speaker) Z SURR R (Surround Right
speaker) Z SUBWFR (Subwoofer) Z (back to the
beginning)
Adjusting the sound
minutes
Changing the scan mode
480i* mZ480p*
AUTO Z 480p* Z 1080i* Z 720p* Z (back to the
beginning)
• There are some progressive TVs and High-Definition TVs that are
not fully compatible with this system, resulting in an unnatural
picture when playing back a DVD VIDEO in the progressive scan
mode. In such a case, change the scan mode to the interlace mode.
• All JVC progressive TVs and High-Definition TVs are fully
compatible with this system.
Basic operations See page 16 for button locations.
TH-C60-40[J]rev-4.book Page 18 Tuesday, April 18, 2006 2:16 PM
Page: 21
19
• The icon such as shows the disc formats or file types the
operation is available for.
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector
to AUDIO.
2 Press DVD or USB MEMORY.
7 To play a disc
1 Press the desired DISC (1-5)
0 on the center unit.
• The system turns on and the disc tray comes
out.
2 Place a disc.
3 Press DISC (1-5), with SHIFT pressed.
NOTE
• Up to 5 discs can be loaded.
• You can also start playback by pressing the following buttons;
– DVD or 3 (play button) on the remote control
– DISC(1-5) 3 or 3 on the center unit.
• The system plays back available discs sequentially until you stop
playback or until the disc loaded on the DISC 5 tray reaches to the
end. However, when DVD VIDEO is loaded in the system, playback
of the disc next to the DVD VIDEO will not start.
7 To play a file in a USB mass storage class device
Press USB MEMORY, then 3 (play button).
The operations of the files in a USB mass storage class device
depend on the file types stored in the device.
• For details on connecting a USB mass storage class device, see
“Connecting a USB mass storage class device”. (See page 13.)
7 When playing the following files...
• For MP3/WMA files
The file control display (see page 27) appears on the TV screen.
• For JPEG files
Each file (still pictures) is shown on the TV screen for about 3
seconds (slide-show). When stopping playback, the file control
display (see page 27) appears on the TV screen.
• For ASF/MPEG-2/MPEG-1 files
When stopping playback, the file control display (see page 27)
appears on the TV screen.
• For DivX files
During the readout time, “Reading Index...” may appear on the
TV screen. When stopping playback, the file control display (see
page 27) appears on the TV screen.
NOTE
• When several types of files are recorded on a disc/device, select
appropriate file type on the setup menu. (See page 34.)
• (For JPEG) The system cannot accept operations even though you
press any buttons before the entire picture appears on the TV screen.
7 To pause playback
Press 8.
To continue playback, press 3 (play button).
7 To stop
Press 7.
The buttons described below are used on pages 19 to 22.
Remote
control mode
selector
(play button)
Number
buttons
Cursor
(3/2)/
ENTER
Basic playback
When placing an 8 cm disc
Label side up
Playback
TH-C60-40[J]rev-4.book Page 19 Tuesday, April 18, 2006 2:16 PM
Page: 22
20
7 On-screen guide icons
During DVD VIDEO playback, the following guide icons may
appear for a while on the TV screen;
• : appears at the beginning of a scene containing multi-subtitle
languages.
• : appears at the beginning of a scene containing multi-audio
languages.
• : appears at the beginning of a scene containing multi-angle
views.
• (Play), (Pause), / (Fast forward/
fast-reverse), / (Slow-motion forward/
reverse): appears when you perform each operation.
• : the disc cannot accept an operation you have tried to do.
NOTE
• If you do not want the on-screen guide icons to appear, see page 35.
7 Playback information on the display window
DVD VIDEO
Example: When a DVD VIDEO encoded with Dolby Digital 5.1 ch
is played.
VCD/SVCD/CD
Example: When a CD is played back.
NOTE
• When a VCD or SVCD with PBC function is played, the elapsed
playing time does not appear, but “PBC” appears.
MP3/WMA file
Example: When an MP3 file is played back.
JPEG file
Example: When slide-show is played back.
ASF/MPEG-2/MPEG-1/DivX file
Example: When an ASF file is played.
NOTE
• You can change the time information mode (except for MP3/WMA/
ASF/MPEG-2/MPEG-1/DivX). (See page 25.)
• You can also check the playback information on the TV screen. (See
page 25.)
Signal and speaker indicators (See page 24.)
Chapter number
Elapsed playing time
(hour:minute:second)
Surround mode and digital signal format (See page 24.)
Title number
Pressing FL DISPLAY
Chapter number
Track number
Elapsed playing time (hour:minute:second)
Signal and speaker
indicators
Track number
Elapsed playing time (hour:minute:second)
(during playback only)
Group number
Track number
Pressing FL DISPLAY
Signal and speaker
indicators
MP3 indicator*
* WMA indicator lights for WMA file.
Group number File number
Pressing FL DISPLAY
File number
Track number
Elapsed playing time (hour:minute:second)
(during playback only)
Group number Track number
Signal and speaker
indicators
Pressing FL DISPLAY
Playback See page 19 for button locations.
TH-C60-40[J]rev-4.book Page 20 Tuesday, April 18, 2006 2:16 PM
Page: 23
21
7 Disc information on the display window
The disc indicators on the display window show the current status
of the corresponding disc tray.
Example: When the discs are loaded to disc trays 1, 2 and 5, and the
disc in the disc tray 5 is selected.
7 Screen saver
An image may burn in on a TV screen if a static picture is displayed
for a long time. To prevent this, the system automatically dims the
screen if a static picture is displayed for over 5 minutes while
playing back a DVD, SVCD, or VCD (the screen saver function).
• Pressing any button will cancel the screen saver function.
• This function does not work when this system outputs the video
signal from HDMI MONITOR OUT terminal.
• If you do not want to use the screen saver function, see page 34.
You can move back the playback position by 10 seconds
from the current position.
7 During playback
Press .
NOTE
• This function works in the same title.
• This feature may not work for some discs.
7 During playback
On the remote control:
Press y or 1.
Each time you press the button, the search
speed changes.
To return to normal speed playback
Press 3 (play button).
On the center unit:
Press and hold x or 4.
Continuously pressing x or 4 increases the fast-forward/
reverse search speed.
NOTE
• When a DVD VIDEO, VCD, SVCD, or ASF/MPEG-2/MPEG-1/
DivX is played back, no sound comes out during fast-forward/reverse
search.
• When a CD or MP3/WMA is played back, sound is intermittent
during fast-forward/reverse search.
• This feature may not work for some discs/files.
• For MP3/WMA:
– The fast-forward/reverse search speed is not shown.
– The fast-forward/reverse search works within a same track.
One Touch Replay
Currently loaded disc number
Currently selected disc
number
Fast-forward/fast-reverse
search
Playback See page 19 for button locations.
TH-C60-40[J]rev-4.book Page 21 Tuesday, April 18, 2006 2:16 PM
Page: 24
22
7 Using x/4 buttons
7 For DVD VIDEO (chapter): During playback
7 For VCD/SVCD (track): During playback
without PBC function
7 For CD/MP3/WMA/JPEG/ASF/MPEG-2/
MPEG-1/DivX (track/file): During playback or while stopped
Press x or 4 repeatedly.
NOTE
• When playing back an MP3/WMA/JPEG/ASF/MPEG-2/MPEG-1/
DivX file, you can make operations using the file control display. (See
page 27.)
• This feature may not work for some discs/files.
7 Using number buttons on the remote control
7 For DVD VIDEO (title, chapter):
While stopped, the title number is selected.
During playback, the chapter number is selected.
7 For VCD/SVCD (track):
During playback or while stopped without PBC function
7 For CD/MP3/WMA/JPEG/ASF/MPEG-2/MPEG-1/DivX
(track/file):
During playback or while stopped
Press number buttons (0-10, h10) to
select the desired number.
• For details on using the number buttons, see “How to use the
number buttons” below.
You can skip within the file at about 5-minute intervals.
This is useful especially when you want to skip within a
long file.
7 During playback
Press Cursor 3/2.
Each time you press the button, the playback position skips to the
beginning of the previous or next interval. Each interval is about
5 minutes.
NOTE
• Intervals are automatically assigned from the beginning of a file.
• This feature is available only within the same file.
• This feature may not work for some discs/files.
7 During playback or while stopped
1 Press TITLE/GROUP.
“– –” is shown in the title/group display area
in the display window.
Example: During DVD VIDEO playback
2 While the display window shows “– –”
,
use number buttons (0-10, h10) to
enter the desired title or group
number.
The system starts playback from the first chapter/track/file of
the selected title/group.
• For details on using the number buttons, see “How to use the
number buttons” on the left column.
NOTE
• This feature may not work for some discs/files.
Skip to the beginning of a
desired selection
How to use the number buttons
To select 3: Press 3.
To select 10: Press 10.
To select 14: Press h10, 1, then 4.
To select 24: Press h10, 2, then 4.
To select 40: Press h10, 4, then 0.
To select 114: Press h10, h10, 1, 1, then 4.
Skipping at about 5-minute
intervals
Locating a desired title/group
using number buttons
Playback See page 19 for button locations.
TH-C60-40[J]rev-4.book Page 22 Tuesday, April 18, 2006 2:16 PM
Page: 25
23
• The icon such as shows the disc formats or file types the
operation is available for.
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
• There are exceptions in the operation mentioned
above. In such a case, follow each instruction.
You can enjoy more realistic sound field than a stereo sound by
using the surround mode.
7 Auto Surround (AUTO SUR)
Used to reproduce the sound as it is recorded without any
conversion (downmixing or simulation, etc.). For example, a
multichannel source is automatically reproduced in multichannel
audio.
7 Dolby Surround
Dolby Pro Logic II*1
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources — stereo source and Dolby
Surround encoded source — into a 5.1 channel.
Dolby Pro Logic II has two modes — Movie mode and Music mode:
• Pro Logic II Movie (MOVIE)
Suitable for reproduction of Dolby Surround encoded sources
bearing the mark .
• Pro Logic II Music (MUSIC)
Suitable for reproduction of any 2 channel stereo music sources.
Dolby Digital*1
Used to reproduce multichannel soundtracks of the software
encoded with Dolby Digital ( ).
• There are other encoding formats of digital surround introduced
by Dolby Laboratories, such as Dolby Digital EX.
7 DTS Digital Surround*2
Used to reproduce multichannel soundtracks of the software
encoded with DTS Digital Surround ( ).
DTS Digital Surround (DTS) is another discrete multichannel
digital audio format available on CD and DVD software.
• There are other encoding formats of multi-channel digital
surround introduced by Digital Theater Systems, Inc., such as
DTS-ES, DTS 96/24.
The buttons described below are used on pages 23 to 32.
Cursor
(3/2/Y/5)/
ENTER
Number
buttons
(play button)
Remote
controlmode
selector
Using the surround mode
Available Surround modes for each input signal
The √ marks show available surround modes.
*1
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories.
*2
“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.
*3 You can select these modes by pressing SURROUND. (See page 24.)
Mode Surround
off
Auto
Surround
Dolby Surround
DTS Digital
Surround
DSP
Signal OFF AUTO SUR MOVIE*3
MUSIC*3
DOLBY D DTS STADIUM*3
ALL ST*3
Dolby D
(Multichannel)
√ √ — — √ — — —
Dolby D
(2 channel)
√ √ √ √ — — √ √
DTS Digital Surround
(Multichannel)
√ √ — — — √ — —
DTS Digital Surround
(2 channel)
√ √ √ √ — — √ √
Analog (VCR) or Linear PCM √ √ √ √ — — √ √
Advanced operations
TH-C60-40[J]rev-4.book Page 23 Tuesday, April 18, 2006 2:16 PM
Page: 26
24
7 DSP
STADIUM
STADIUM mode adds clarity and spreads the sound, like in an
outdoor stadium.
All Channel Stereo
All Channel Stereo (ALL ST) mode can reproduce a larger stereo
sound field using all the connected (and activated) speakers.
All Channel Stereo can be used while reproducing 2 channel stereo
source.
7 Indicators on the display window
Digital signal format indicators
LPCM: Lights when Linear PCM signal comes in.
GD: Lights when Dolby Digital signals come in.
C: Lights when DTS Digital (Surround) signals come
in.
No indication: No digital signal indicator lights when analog
signals come in.
Dolby Surround mode indicator
GPLII: Lights when Dolby Pro Logic II mode is activated.
Surround indicator
SURR: Lights when the surround mode is activated.
Source signal indicators, etc.
Light to indicate the incoming signals.
a: Lights when the left channel signal comes
in.
b: Lights when the center channel signal comes in.
c: Lights when the right channel signal comes in.
d: Lights when the LFE channel signal comes in.
g: Lights when the surround left channel signal comes in.
i: Lights when the surround right channel signal comes in.
h: Lights when the monaural surround channel signal or 2
channel Dolby Surround signal comes in.
SW (Subwoofer): Always lights.
The channel with “ ” shows that the corresponding speakers are
reproducing the channels’ sound.
If the channels’ sound decoded into 5.1 channel is reproduced, only
“ ” lights.
Selecting the surround mode
The system is set up to automatically select the optimal surround
mode for input signal from digital multichannel software.
When playing back a 2 channel source, you can select the desired
surround mode manually.
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
7 When playing back digital multichannel
software (except while OFF is selected)
The appropriate multichannel surround mode (Dolby Digital or
DTS Digital Surround) is automatically selected.
7 When playing back a 2 channel source
You can select either Dolby Pro Logic II (MOVIE/MUSIC) or the
DSP mode.
Press SURROUND repeatedly to select the
desired mode.
The surround mode is turned on and the current surround mode
appears on the display window.
Each time you press the button, the surround mode changes.
For details on each mode, see “Available Surround modes for each
input signal”. (See page 23.)
To turn off the surround mode
Press SURROUND repeatedly until “OFF”
appears on the display window.
Storing adjustments — auto memory
When you turn the power off, the system memorizes the current
surround mode. The memorized mode is automatically recalled
when you turn the power on.
NOTE
• For ASF, MPEG-2, MPEG-1 and DivX (except DivX version 6), the
surround mode takes no effects.
Normal stereo sound All Channel Stereo
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 24 Tuesday, April 18, 2006 2:16 PM
Page: 27
25
You can check disc information and you can use some functions
using the on-screen bar.
Showing the on-screen bar
7 Whenever a disc is loaded
Press ON SCREEN.
Each time you press the button, the on-
screen bar changes as follows on the TV screen.
Example: During DVD VIDEO playback
• The currently selected item shows as green with an arrow.
7 Contents of the on-screen bar during playback
DVD VIDEO
VCD
SVCD
CD
ASF/MPEG-2/MPEG-1/DivX
1 Shows disc type.
2 Shows audio information.
3 Shows disc number.
4 Shows current title number.
5 For DVD VIDEO: Shows current chapter number.
For other type of discs: Shows current track number.
6 Shows time information. See “Changing the time information”
below.
7 Shows playback status.
: appears during playback.
/ : appears during fast forward/reverse.
/ : appears during playback in forward slow-motion/
reverse slow-motion.
: appears when paused.
: appears when stopped.
8 Select this to change time information (F). See “Changing the
time information” below.
9 Select this for Repeat Playback. (See page 31.)
0 Select this for time search function. (See page 27.)
K Select this for chapter search function. (See page 26.)
L Select this to change audio language or channel. (See page 29.)
M Select this to change subtitle language and subpicture. (See page
28.)
N Select this to change view angle. (See page 28.)
O Shows Playback mode status.
PROGRAM: appears during Program Playback. (See page 30.)
RANDOM: appears during Random Playback. (See page 31.)
P Shows Repeat mode status. (See page 31.)
Changing the time information
You can change the time information in the
on-screen bar on the TV screen and the
display window of the center unit.
7 During playback
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER repeatedly to select the
desired information.
Example: When elapsed playing time of disc is selected.
7DVD VIDEO
• Time: Elapsed playing time of current chapter
• REM: Remaining time of current chapter
• TOTAL: Elapsed time of title
• T. REM: Remaining time of title
7VCD/SVCD/CD
• Time: Elapsed playing time of current track
• REM: Remaining time of current track
• TOTAL: Elapsed time of disc
• T. REM: Remaining time of disc
4 Press ON SCREEN.
The on-screen bar disappears.
Using the on-screen bar
OFF
(The on-screen bar disappears)
(back to the beginning)
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 25 Tuesday, April 18, 2006 2:16 PM
Page: 28
26
You can start playing a title, chapter or track you specify. You can
also play a disc from specified time.
Locating a desired scene from the DVD menu
DVD VIDEOs generally have their own menus which show
disc contents and you can display them on the TV screen.
You can locate a desired scene by using these menus.
7 Whenever a DVD VIDEO is loaded
1 Press TOP MENU or MENU.
The menu appears on the TV screen.
Normally, a DVD VIDEO which contains more than one title
will have a “top” menu which lists the titles. Press TOP MENU
to show the title menu.
Some discs may also have a different menu which is shown by
pressing MENU.
See the instructions for each discs regarding its particular
menu.
2 Use Cursor 3/2/Y/5 to select a
desired item.
3 Press ENTER.
• With some discs, you can also select items by entering the
corresponding number using number buttons.
NOTE
• This feature may not work for some discs.
Locating a desired scene using a VCD/SVCD menu
with PBC
A VCD or SVCD recorded with PBC has its own menus
such as a list of contained songs. You can locate a
specific scene by using these menus.
7 During playback with PBC function
1 Press RETURN repeatedly until the
menu appears on the TV screen.
2 Press number buttons (0-10, h10) to
select the number of the desired item.
• For details on using the number buttons, see “How to use the
number buttons”. (See page 22.)
To return to the menu
Press RETURN repeatedly until the menu screen appears.
When “NEXT” or “PREVIOUS” is shown on the TV screen:
• To go to the next page, press x.
• To return to the previous page, press 4.
NOTE
• If you want to play a PBC-compatible VCD/SVCD without using the
PBC function, perform any of the following:
– Start playback by pressing number buttons while stopped.
– Press x repeatedly until the desired track number is displayed,
then start playback by pressing 3 (play button). The track number
appears on the display window instead of “PBC”.
• To activate the PBC function when playing a PBC-compatible VCD/
SVCD without using the PBC function, perform any of the following:
– Press TOP MENU or MENU.
– Press 7 twice to stop playback, then press 3 (play button).
Locatingadesiredchapterusingtheon-screen bar
7 During playback
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press number buttons (0-9, h10) to
enter the desired chapter number.
Example:
To select 8: Press 8.
To select 10: Press h10, 1, then 0.
To select 20: Press h10, 2, then 0.
To select 37: Press h10, 3, then 7.
To correct a misentry
Repeat step 4.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
NOTE
• You can select up to the 99th chapter.
Playing from a specified
position on a disc
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 26 Tuesday, April 18, 2006 2:16 PM
Page: 29
27
Locating a desired position by specifying the time
7 For DVD VIDEO: During playback
7 For VCD/SVCD: While stopped or during
playback without PBC function
7 For CD: During playback or while stopped
7 When specifying the elapsed playing time from the
beginning of the disc
Perform the following procedure while stopped.
7 When specifying the elapsed playing time from the
beginning of the current title/track
Perform the following procedure during playback.
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Use number buttons (0-9) to enter the
time.
Example: To play back from a point 2 (hours): 34 (minutes): 08
(seconds) elapsed
To correct a misentry
Press Cursor 2 repeatedly.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
You can search and play desired groups and tracks/
files using the file control display on the TV
screen.
Example: When the source is DVD.
* When the source is USB MEMORY, “USB” appears.
The file control display appears automatically during playback
(MP3/WMA) or while stopped.
7 For MP3/WMA: During playback or while stopped
7 For JPEG/ASF/MPEG-2/MPEG-1/DivX: While stopped
1 Press Cursor 3/2/Y/5 to select the
desired group/track/file.
• For MP3/WMA, playback starts from the selected track.
2 Press 3 (play button) or ENTER.
• Track playback/slide-show starts from the selected track/file.
• When you press ENTER for JPEG, only the selected file is
played back.
NOTE
• (For MP3/WMA) During playback, you can locate the desired track/
file by pressing x/4 or Cursor 5/Y.
• You can also check playback information on the display window. (See
page 20.)
• Some group, track and file names may not be displayed correctly
depending on recording conditions.
• The order of groups, tracks, and files may be displayed differently
from the order displayed on your personal computer.
• The extension of the file may not be displayed if the file name is too
long.
Press 2 Press 3
Press 4
Press 8
Press 0
Using the file control display
Current group/total group
number
Current track (file)
Track information (for MP3/
WMA only)
Repeat mode
Elapsed playing time of current
track (except for JPEG)
Playback status
Current track (file) / total track (file)
number on current group
Current group
Total track (file)
number on disc
*
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 27 Tuesday, April 18, 2006 2:16 PM
Page: 30
28
When Resume Playback is set to “ON” (see page
35) and you stop playback by the following
operations, the position where playback has been
stopped is stored. (RESUME indicator lights on
the display window.)
• Turning off the power* (See page 16.)
• Pressing 7 once
* Only when playing back a DVD.
To start playback from the stored position
Press 3 (play button) or DVD.
• There may be a case when 3 (play button) does not work after
changing the source. In this case, select DVD as a source.
• Pressing DISC (1-5) (with SHIFT pressed) on the remote control or
DISC (1-5) 3 on the center unit also resumes disc playback.
To clear the stored position
Press 7 again.
• Opening the disc tray with the playback disc also clears the stored
position.
NOTE
• When USB MEMORY is selected as the source, the beginning of a file
where playback has been stopped is stored.
• (For DivX) The beginning of a scene where playback has been
stopped may be stored.
7 During playback of a disc containing multi-view angles
When using the ANGLE button:
1 Press ANGLE.
Example: The first view angle is selected out of 3 view angles
recorded.
2 Press ANGLE repeatedly, or press
Cursor Y/5 to select the desired view
angle.
When using the on-screen bar:
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press Cursor Y/5 to select the desired
view angle.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
7 During playback of a disc/file containing
subtitles in several languages
When using the SUBTITLE button:
1 Press SUBTITLE.
Example (DVD VIDEO): “ENGLISH” is selected out of 3
subtitle languages recorded.
2 Press SUBTITLE repeatedly, or press
Cursor Y/5 to select the desired
subtitle.
For SVCD
• An SVCD can contain up to four subtitles. Pressing SUBTITLE
changes the subtitles regardless of whether the subtitles are
recorded or not. (Subtitles will not change if no subtitle is
recorded.)
To clear the subtitle
Select “OFF” in step 2.
When using the on-screen bar:
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press Cursor Y/5 repeatedly to select
the desired subtitle.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
To clear the subtitle
Select “OFF” in step 4.
NOTE
• Some subtitle or audio languages are abbreviated in the pop-up
window. See “The language codes list”. (See page 33.)
• For DivX, you cannot operate this procedure using the on-screen bar.
Resume Playback
Selecting a view angle
Selecting the subtitle
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 28 Tuesday, April 18, 2006 2:16 PM
Page: 31
29
7 During playback of a disc/file containing
audio in several languages
When using the AUDIO button:
1 Press AUDIO.
Example (DVD VIDEO): “ENGLISH” is selected out of 3 audio
languages recorded.
2 Press AUDIOrepeatedly or press Cursor
Y/5 to select the desired audio.
When using the on-screen bar:
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press Cursor Y/5 to select the desired
audio.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
NOTE
• Some subtitle or audio languages are abbreviated in the pop-up
window. See “The language codes list”. (See page 33.)
• “ST”, “L”, or “R” is displayed when playing a VCD respectively
representing “stereo”, “left sound” and “right sound”.
When playing a SVCD, “ST1”, “ST2”, “L1”, “R1”, “L2”, or “R2” is
displayed.
• For DivX, you cannot operate this procedure using the on-screen bar.
Frame-by-frame playback
7 During playback
Press 8 repeatedly.
Each time you press the button, the still picture
advances by one frame.
To return to normal playback
Press 3 (play button).
Playing back in slow-motion
7 During playback
1 Press 8 at the point where
you want to start playback in slow-
motion from.
The system pauses playback.
2 Press SLOW 9.
Playback in forward slow-motion starts.
For DVD VIDEO only:
• To play back in reverse slow-motion, press SLOW (.
Each time you press the button, the playback speed becomes
faster.
Example: On the TV
To return to normal playback
Press 3 (play button).
NOTE
• Sound cannot be heard during slow-motion playback.
Zooming in
7 During playback or while paused
1 Press ZOOM with SHIFT
pressed.
Each time you press ZOOM with SHIFT pressed, scene
magnification changes.
2 While zoomed in, press Cursor 3/2/
Y/5 to move zoom-in area.
To return to normal playback
Press ZOOM repeatedly with SHIFT pressed, to select ZOOM M 1.
NOTE
• The number of the magnification steps varies depending on the disc
type.
• During playback, there may be a case where Cursor (3/2/Y/5)
does not work in step 2 above.
Selecting the audio Special picture playback
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 29 Tuesday, April 18, 2006 2:16 PM
Page: 32
30
Changing the VFP setting
The VFP (Video Fine Processor) function enables
you to adjust the picture character according to
the type of programming, picture tone or
personal preference (except when connecting the TV through
HDMI MONITOR OUT terminal).
7 During playback
1 Press VFP.
The current VFP settings appear on the TV screen.
Example:
2 Press Cursor 3/2 repeatedly to select
the VFP mode.
• NORMAL: Normally select this.
• CINEMA: Suitable for movies.
When you select “NORMAL” or “CINEMA”, press VFP to
complete the setting.
• USER 1 and USER 2: You can adjust parameters that affect
picture appearance.
Only when selecting “USER 1” or “USER 2” in step 2, proceed
to perform the following operation;
3 Press Cursor Y/5 repeatedly to select
a parameter you want to adjust.
Adjust gradually and confirm picture appearance results are as
preferred.
• GAMMA: Controls brightness of neutral tints while
maintaining brightness of dark and bright portions.
• BRIGHTNESS: Controls screen brightness.
• CONTRAST: Controls screen contrast.
• SATURATION: Controls screen color depth.
• TINT: Controls screen tint.
• SHARPNESS: Controls screen sharpness.
4 Press ENTER.
Example:
5 Press Cursor Y/5 to change the
setting.
6 Press ENTER.
The current VFP settings appear again.
7 Repeat steps 3 to 6 to adjust other
parameters.
8 Press VFP.
NOTE
• Although the setting display disappears in the middle of the
procedure, the setting at that time will be stored.
• The VFP function is not available when connecting the TV through
HDMI MONITOR OUT terminal.
7 While stopped
1 Press PLAY MODE repeatedly until
program window appears on the TV
screen.
PRG indicator lights on the display window.
2 Follow the instructions that appear on
the TV screen to program the desired
tracks.
• For details on using the number buttons, see “How to use the
number buttons”. (See page 22.)
• You can specify the tracks whose number is up to 99.
• Normally the system automatically skips to the Track/
Chapter column after entering the disc number. However,
there may be a case that the number can be entered in the
Title/Group column. In such a case, press 1 (number button)
to proceed to the Track/Chapter column.
• When you press ENTER instead of the number buttons in the
Track/Chapter column, “ALL” appears and all the tracks on
the selected disc are programmed as a step.
To clear the programs one by one from the last entered
number
Press CANCEL repeatedly.
To clear all programs
Press 7.
You can also clear the program by turning off the system.
3 Press 3 (play button).
If all of the programmed tracks have been played back,
playback stops and the program window appears again. Note
that program setting remains.
To check the program contents
During playback, press 7. Playback stops and the program window
appears.
To quit the Program mode
While stopped, press PLAY MODE repeatedly until both program
window and disappear from the TV screen.
NOTE
• The Resume function cannot be used with Program Playback.
• DISC (1-5) on the remote control and DISC (1-5) 3 on the center unit
do not work during Program Playback.
• Program Playback may not work for some discs.
Program Playback
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 30 Tuesday, April 18, 2006 2:16 PM
Page: 33
31
You can play tracks on a disc in random order.
7 While stopped
1 Press PLAY MODE repeatedly until
appears on the TV screen.
RND indicator lights on the display window.
2 Press 3 (play button).
• When more than one discs are loaded, the system starts
Random Playback of the next disc after completing current
disc playback.
To quit Random mode
While stopped, press PLAY MODE repeatedly until both program
window and disappear from the TV screen.
You can also clear the Random mode by turning off the system.
Repeating the current selection or all discs
7 For DVD VIDEO: During playback
7 For VCD/SVCD: During playback without PBC
function or while stopped
7 For CD/MP3/JPEG/ASF/MPEG-2/MPEG-1/
DivX: During playback or while stopped
When using the REPEAT button:
Press REPEAT.
Each time you press REPEAT, the Repeat mode changes.
NOTE
• When DVD VIDEO is loaded in the system, playback of the disc next
to the DVD VIDEO will not start, although /REPEAT ALL
on the TV screen or ALL in the display window is shown.
• For DVD VIDEO, REPEAT ALL and REPEAT DISC may not be
available depending on the disc.
When using the on-screen bar (except for MP3/WMA/JPEG/
ASF/MPEG-2/MPEG-1/DivX):
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press Cursor Y/5 repeatedly to select
the Repeat mode.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
To cancel Repeat Playback
Select “OFF” in step 4.
Random Playback
Repeat Playback
Repeat mode indicator
Display
window
TV screen Meanings
Repeats the current group for
MP3/WMA/JPEG/ASF/
MPEG-2/MPEG-1/DivX.
REPEAT GROUP
Repeats the current title for
DVD VIDEO.
DISC
Repeats all titles and tracks on
the current disc for VCD/
SVCD/CD/MP3/WMA/JPEG/
ASF/MPEG-2/MPEG-1/DivX.
REPEAT DISC
ALL
Repeats all the available discs/
files.
REPEAT ALL
1
, Repeats the current track for
VCD/SVCD/CD/MP3/WMA/
ASF/MPEG-2/MPEG-1/DivX.
REPEAT TRACK,
REPEAT STEP
,
Repeats the current chapter for
DVD VIDEO.
No
indication
Repeat mode is off.
The system plays back the disc/
file normally.
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 31 Tuesday, April 18, 2006 2:16 PM
Page: 34
32
Repeating a desired part [A-B Repeat]
You can repeat playback of a desired part by
specifying the beginning (point A) and
ending (point B).
7 During playback
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight .
3 Press ENTER.
4 Press Cursor Y/5 repeatedly to select
“A-B”.
5 Press ENTER at the beginning of the
part you want to repeat (point A).
The repeat mode indicator “ ” appears on the display
window.
6 Press ENTER at the end of the part you
want to repeat (point B).
The repeat mode indicator on the display window changes to
“ ” and A-B Repeat Playback starts.
7 Press ON SCREEN.
The on-screen bar disappears.
To cancel
Select “OFF” in step 4, then press ENTER.
NOTE
• When playing back a DVD VIDEO, A-B Repeat Playback is possible
only within the same title.
• When playing back a VCD, SVCD, or CD, A-B Repeat Playback is
possible only within the same track.
• “A-B” cannot be selected during Program and Random Playback.
• “A-B” cannot be selected during playback with PBC function.
You can lock the tray and prohibit unwanted disc ejection.
On the center unit ONLY:
While the system is turned off
• “LOCKED” appears on the display window.
• If you try to eject the disc, “LOCKED” appears to indicate that
the tray is locked.
To cancel
Carry out the same operation again.
• “UNLOCKED” appears on the display window.
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
NOTE
• Before you start operation; There is a time limit when
doing the following steps. If the setting is canceled before you finish,
start from step 1 again.
1 Press SETTING.
Example:
2 Press Cursor Y/5 to select the item
you want to set.
• BAL. (Balance):
You can adjust the balance of the sound between “R (right) –
21” and “L (left) –21”. To set the balance to normal, select
“CNTR (center)”.
• MON. (Monitor Out):
Select the video output jack type by which you watch DVD
playback after connecting your TV. (See page 12.) Set the
video output to use AV COMPU LINK remote control
system. (See page 38.)
VIDEO: To watch DVD playback via the VIDEO jack.
S: To watch DVD playback via the S-VIDEO jack.
COMP (Component):
To watch DVD playback via the COMPONENT
VIDEO OUT jacks.
HDMI: To watch DVD playback via the HDMI
MONITOR OUT terminal.
When selecting this setting, AV COMPU LINK
remote control system for the built-in DVD
player does not work.
3 Press Cursor 3/2 to make an
adjustment or selection.
Example:
The adjustment is set and the display automatically disappears
a few seconds later.
Tray lock
Press and hold
Sound and other settings
Advanced operations See page 23 for button locations.
TH-C60-40[J]rev-4.book Page 32 Tuesday, April 18, 2006 2:16 PM
Page: 35
33
• You can change the language used in the setup menus. See “Menu
description” below.
Basic operation on the setup menus
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector
to AUDIO.
2 Press DVD or USB MEMORY.
7 While stopped
1 Press SET UP.
2 Follow the instructions that appear on
the TV screen.
: Language menu (LANGUAGE)
7 MENU LANGUAGE
Some DVDs have their own menus in multiple languages.
• Select the initial language*.
7 AUDIO LANGUAGE
Some DVDs have multiple audio languages.
• Select the initial audio language*.
7 SUBTITLE
Some DVDs have multiple subtitle languages.
• Select the initial subtitle language*.
7 ON SCREEN LANGUAGE
• Select the language shown on the TV screen when operating this
system.
* When the language you have selected is not recorded to a disc,
the original language is automatically used as the initial language.
NOTE
• See the following “The language codes list” for the code of each
language, such as “AA”, etc.
The language codes list
Using the setup menus
Menu description
Cursor
(3/2/Y/5)/
ENTER
AA Afar IK Inupiak RN Kirundi
AB Abkhazian IN Indonesian RO Rumanian
AF Afrikaans IS Icelandic RW Kinyarwanda
AM Ameharic IW Hebrew SA Sanskrit
AR Arabic JI Yiddish SD Sindhi
AS Assamese JW Javanese SG Sangho
AY Aymara KA Georgian SH Serbo-Croatian
AZ Azerbaijani KK Kazakh SI Singhalese
BA Bashkir KL Greenlandic SK Slovak
BE Byelorussian KM Cambodian SL Slovenian
BG Bulgarian KN Kannada SM Samoan
BH Bihari KO Korean (KOR) SN Shona
BI Bislama KS Kashmiri SO Somali
BN Bengali, Bangla KU Kurdish SQ Albanian
BO Tibetan KY Kirghiz SR Serbian
BR Breton LA Latin SS Siswati
CA Catalan LN Lingala ST Sesotho
CO Corsican LO Laothian SU Sundanese
CS Czech LT Lithuanian SV Swedish
CY Welsh LV Latvian, Lettish SW Swahili
DA Danish MG Malagasy TA Tamil
DZ Bhutani MI Maori TE Telugu
EL Greek MK Macedonian TG Tajik
EO Esperanto ML Malayalam TH Thai
ET Estonian MN Mongolian TI Tigrinya
EU Basque MO Moldavian TK Turkmen
FA Persian MR Marathi TL Tagalog
FI Finnish MS Malay (MAY) TN Setswana
FJ Fiji MT Maltese TO Tonga
FO Faroese MY Burmese TR Turkish
FY Frisian NA Nauru TS Tsonga
GA Irish NE Nepali TT Tatar
GD Scots Gaelic NL Dutch TW Twi
GL Galician NO Norwegian UK Ukrainian
GN Guarani OC Occitan UR Urdu
GU Gujarati OM (Afan) Oromo UZ Uzbek
HA Hausa OR Oriya VI Vietnamese
HI Hindi PA Panjabi VO Volapuk
HR Croatian PL Polish WO Wolof
HU Hungarian PS Pashto, Pushto XH Xhosa
HY Armenian PT Portuguese YO Yoruba
IA Interlingua QU Quechua ZU Zulu
IE Interlingue RM Rhaeto-Romance
Setting DVD preferences
TH-C60-40[J]rev-4.book Page 33 Tuesday, April 18, 2006 2:16 PM
Page: 36
34
: Picture menu (PICTURE)
7 MONITOR TYPE
You can select the monitor type to match your TV when you play
DVDs recorded in the picture’s height/width ratio of 16:9.
• 4:3 PS (Pan Scan conversion)
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars do not
appear, however, the left and right edges of the pictures will not
be shown on the screen.
• 4:3 LB (Letter Box conversion)
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars appear
on the top and the bottom of the screen.
• 16:9 (Wide television conversion)
Select this when the aspect ratio of your TV is fixed on 16:9 (wide
TV).
When you play DVDs recorded in the picture’s height/width ratio
of 4:3, the system adjust the ratio of output signal automatically.
NOTE
• Even if “4:3 PS” is selected, the screen size may become “4:3 LB” with
some DVDs. This depends on how DVDs are recorded.
• When the scan mode is set to “1080i” or “720p” (see page 18), “16:9”
is automatically selected.
7 PICTURE SOURCE
When you set the scan mode to “480p” or “720p” (see page 18), you
can obtain optimal picture quality by selecting whether the content
on the disc/file is processed by frame (film source) or by field (video
source).
Normally set to “AUTO”.
• AUTO
Used to play a disc/file containing both video and film source
materials.
This system recognizes the source type (video or film) of the
current disc/file according to the disc/file information.
If the playback picture is unclear or noisy, or the oblique lines of
the picture are rough, try to change to other modes.
• FILM
Suitable for playing back a film source disc/file.
• VIDEO (NORMAL)
Suitable for playing back a video source disc/file with relatively a
few movements.
• VIDEO (ACTIVE)
Suitable for playing back a video source disc/file with relatively a
lot of movements.
7 SCREEN SAVER (See page 21.)
You can activate or deactivate screen saver function.
7 FILE TYPE
When several types of files are recorded on a disc/device, you can
select which files to play.
• AUDIO
Select this to play MP3/WMA files.
• STILL PICTURE
Select this to play JPEG files.
• VIDEO
Select this to play ASF/MPEG-2/MPEG-1/DivX files.
7 HDMI DVI COLOR
When connecting the TV by using HDMI cable, you can adjust the
picture appearance, such as image quality, color intensity, and black
fading.
• STANDARD
Select this when you need no picture adjustment.
• ENHANCE
This system automatically makes picture adjustment suitable for
the picture.
7 HDMI OUT
When connecting the TV by using HDMI cable, you can select the
type of video signal output from HDMI MONITOR OUT terminal.
Normally set to “AUTO”.
• AUTO
This system automatically select the video signal type and outputs
according to the type of TV connected with HDMI cable.
• RGB
Select this when no picture appears on the TV with “AUTO”
setting. The video signal output is fixed to RGB.
: Audio menu (AUDIO)
7 D. RANGE CONTROL
(Dynamic range control)
You can enjoy low level recorded sound clearly at night even at a low
volume when listening to the sound with Dolby Digital.
• WIDE RANGE
Select this when you want to enjoy surround sound with its full
dynamic range (no effect applied).
• NORMAL
Normally select this to activate this function.
• TV MODE
Select this when you want to fully apply the compression effect
(useful at midnight).
NOTE
• When you play a multichannel Dolby Digital source with the
surround mode is off, the setting of D. RANGE CONTROL is set to
NORMAL automatically.
7 HDMI AUDIO OUT
You can select whether the system outputs the audio signal with the
video signal from HDMI MONITOR OUT terminal or not.
Ex.: 16:9
Ex.: 4:3 LB
Ex.: 4:3 PS
Setting DVD preferences
TH-C60-40[J]rev-4.book Page 34 Tuesday, April 18, 2006 2:16 PM
Page: 37
35
: Speaker setting menu (SPK. SETTING)
7 Level menu (LEVEL)
FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/CENTER
SPEAKER/SURROUND RIGHT SPEAKER/SURROUND LEFT
SPEAKER
While monitoring the test tone, adjust the center and surround
speakers volume as much as that of the front speakers.
You can adjust the output level in the -6 dB to +6 dB range.
TEST TONE*
Outputs the test tone.
* The test tone comes out of all of the activated speakers in the
following sequence:
s Front left speaker s Center speaker s Front right
speaker s Surround right speaker s Surround left speaker
s (back to the beginning)
NOTE
• Adjustment of subwoofer output level is not available.
7 Delay menu (DELAY)
Example:
Set to “0 ms” for the furthest speaker from your position as the basis
for the delay time setting.
In this case, set the delay time of each speaker as follows;
• Delay time of front speakers: 0 ms
• Delay time of center speaker: 1 ms
• Delay time of surround speakers: 2 ms
FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/CENTER
SPEAKER/SURROUND RIGHT SPEAKER/SURROUND LEFT
SPEAKER
Adjust the distance from the listening position to the speakers.
Within the range from 0 ms to 15 ms (by 1 ms).
7 Subwoofer menu (SUBWOOFER)
LEVEL
You can set the output level of the subwoofer in the -6 dB to +6 dB
range.
CROSS OVER
The signals below the preset frequency level will be sent to and be
reproduced by the subwoofer.
Select one of the crossover frequency levels according to the size of
the small speaker connected.
• 120Hz: Select when the cone speaker unit built in the speaker is
about 8 cm (3-3/16 inches).
• 150Hz: Select when the cone speaker unit built in the speaker is
about 6 cm (2-3/8 inches).
• 200Hz: Select when the cone speaker unit built in the speaker is
about 5 cm (2 inches).
: Other setting menu (OTHERS)
7 RESUME
You can activate or deactivate Resume Playback function. (See page
28.)
7 ON SCREEN GUIDE
You can activate or deactivate the on-screen guide icons. (See page
20.)
7 DivX registration menu (DivX REGISTRATION)
The system has its own Registration Code for DivX playback.
You can confirm the code of your system.
• Once you play back a disc created by using the Registration Code,
the system’s code is overwritten by a totally different new one for
copyright protection purpose.
Subwoofer
Front left
0 ms
Center speaker
1 ms
Front right
0 ms
Surround left
2 ms
Surround right
2 ms
1 ms increase (or decrease) in delay time corresponds to about
30 cm (1 ft) decrease (or increase) in distance.
3.0 m
(10 ft)
2.7 m
(9 ft)
2.4 m
(8 ft)
2.1 m
(7 ft)
Setting DVD preferences
TH-C60-40[J]rev-4.book Page 35 Tuesday, April 18, 2006 2:16 PM
Page: 38
36
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector to
AUDIO.
2 Press FM/AM.
On the remote control:
1 Press FM/AM repeatedly to select the
band.
Example:
When the system is tuned in to 810 kHz.
2 Press TUNING 9/( repeatedly until
you find the frequency you want.
When you hold down the button until the system starts
searching for stations and then release it, the system stops
searching automatically when a station of sufficient signal
strength is tuned in to.
On the center unit:
1 Press SOURCE repeatedly to select the
band (FM or AM).
2 Press TUNING +/– repeatedly until you
find the frequency you want.
NOTE
• When an FM stereo program is received, the ST indicator lights on
the display window.
The buttons described below are used on pages 36 and 37.
Number
buttons
Remote
control mode
selector
Cursor
(3/2)
Manual tuning
Tuner operations
TH-C60-40[J]rev-4.book Page 36 Tuesday, April 18, 2006 2:16 PM
Page: 39
37
Once a station is assigned to a channel number, the station can be
quickly tuned in. You can preset 30 FM and 15 AM stations.
7 To preset the stations
1 Tune in the station you want to preset.
• If you want to store the FM reception mode for an FM
station, select the reception mode you want. See “Selecting
the FM reception mode” on the right column.
Example: When the system is tuned in to 103.5 MHz.
2 Press MEMORY.
While “CH” and “_ _” are flashing:
3 Press number button(s) (1-10, h10) to
select a preset number you want.
• For details on using the number buttons, see “How to use the
number buttons”. (See page 22.)
Example: When the preset channel 1 is selected.
If the setting is canceled before you finish, start from step 2
again.
While the selected number is flashing:
4 Press MEMORY.
“STORED” appears on the display window.
The station is assigned to the selected preset number.
If the setting is canceled before you finish, start from step 2
again.
5 Repeat steps 1 to 4.
• Storing a new station to a used number erases the previously
stored one.
7 To tune in to a preset station
1 Press FM/AM repeatedly to select FM or
AM.
2 Press number button(s) (1-10, h10) to
select a preset number.
• For details on using the number buttons, see “How to use the
number buttons”. (See page 22.)
NOTE
• You can also select a preset number by pressing Cursor 3/2.
When the stereo FM program currently tuned in is noisy, you can
change the FM reception mode to improve the reception.
7 While listening to an FM station
Press FM MODE.
The FM reception mode appears on the display window.
Each time you press the button, the FM reception mode changes.
• AUTO:
When a program is broadcast in stereo, you will hear stereo
sound. (The ST indicator lights on the display window.) When in
monaural, you will hear monaural sound. This mode is also
useful to suppress static noise between stations.
• MONO:
Reception will be improved although you will lose the stereo
effect. (The MONO indicator lights on the display window.) In
this mode, you will hear noise until you are tuned in to a station.
When listening to an AM broadcast with a lot of noise interference,
you can change the Beat Cut mode to reduce the noise.
7 While listening to an AM station
Press FM MODE.
The current Beat Cut mode appears on the display window.
Each time you press the button, the Beat Cut mode changes.
• Choose “BEATCUT1” or “BEATCUT2” according to which gives
clearer sound.
Preset tuning Selecting the FM reception
mode
Reducing the noise of AM
broadcast
Tuner operations See page 36 for button locations.
TH-C60-40[J]rev-4.book Page 37 Tuesday, April 18, 2006 2:16 PM
Page: 40
38
The AV COMPU LINK remote
control system allows you to operate
JVC TVs and VCRs through the center unit. This system is
equipped with the AV COMPU LINK-III, which adds a function to
operate JVC’s video components via the video components
terminals. To use this remote control system, you need to connect
the video components you want to operate as follows.
• Refer also to the manuals supplied with your TV and video
components.
Connecting a TV and VCR
CAUTION
Before connecting;
• If you have already plugged your VCR, TV and the center unit into
the AC outlets, unplug their AC power cords first.
1 Connect the center unit to a TV and
VCR.
• For details, see pages 12 and 13.
2 Connect the center unit to a TV and
VCR using the optional AV COMPU
LINK cords.
3 Plug the AC power cords of the VCR, TV
and the center unit into the AC outlets.
4 Turn on the connected components
first, then turn on the center unit.
• When turning on the TV for the first time after the AV
COMPU LINK connection, turn the TV volume to minimum
using the TV volume control on the TV.
• When turning on the VCR, use the remote control supplied
with this system. (Press F VCR/DBS.)
NOTE
• To correctly use the automatic selection of TV input mode, select the
correct “MON.” (Monitor Out) setting. (See page 32.)
Available functions
The AV COMPU LINK remote control system allows you to use the
functions listed following.
One-touch video play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy video playback without manually setting other
switches. This system automatically turns on and changes the
source to VCR.
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab in place, press
the play (3) button on the VCR or on the remote control to get the
same result.
One-touch DVD play
Simply by starting playback on the built-in DVD player, you can
enjoy playback without manually setting other switches. The TV
automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
Automatic selection of TV input mode
When you select DVD or VCR as the source to play on the system,
the TV automatically changes the input mode to the appropriate
position so that you can view the playback picture.
Automatic Power On/Off
The TV and VCR turn on and off along with the system.
When you turn on the system;
• If the previously selected source is “DVD”, only the TV will turn
on automatically.
• If the previously selected source is “VCR”, the TV and VCR will
turn on automatically.
When you turn off the system, the TV and VCR will turn off.
NOTE
• If you turn off the system while recording on the VCR, the VCR will
not turn off and will continue recording.
• When starting playback on the VCR with “HDMI” selected for
“MON.” (Monitor Out) setting (see page 32), the system
automatically turns on and changes the source to VCR, while the TV
does not automatically turn on nor change the input mode. In this
case, turn the TV on and change the input mode of the TV manually.
TV
AV COMPU LINK cord
(not supplied)
VCR
Center unit
AV COMPU LINK remote control system
TH-C60-40[J]rev-4.book Page 38 Tuesday, April 18, 2006 2:16 PM
Page: 41
39
7 Handling Discs
• Remove the disc from its case by holding it at
the edge while pressing the center hole lightly.
• Do not touch the shiny surface of the disc or
bend the disc.
• Put the disc back in its case after use to
prevent warping.
• Be careful not to scratch the surface of the disc
when placing it back in its case.
• Avoid exposure to direct sunlight, extreme
temperature and moisture.
To clean the disc
Wipe the disc with a soft cloth in a straight line
from center to edge.
• DO NOT use any solvent — such as
conventional record cleaner, spray,
thinner or benzine — to clean the disc.
7 Cleaning the system
• Stains on the system should be wiped off with a soft cloth. If the
system is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the system may deteriorate in quality, become damaged or
get its paint peeled off, be careful about the following.
–DO NOT wipe it with a hard cloth.
–DO NOT wipe it forcefully.
–DO NOT wipe it with thinner or benzine.
–DO NOT apply any volatile substance such as insecticides to it.
–DO NOT allow any rubber or plastic to remain in contact with
it for a long time.
If there are any other cases than the noted above or if this system does not seem to work properly, turn off the system and turn it back on.
Maintenance
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Power does not come on. The power cord and/or system cord is not connected. Connect the power cord and system cord correctly. (See
page 13.)
The remote control does
not work.
The batteries are exhausted. Replace the batteries. (See page 7.)
Sunlight is shining directly on the remote sensor. Hide the remote sensor from direct sunlight.
The disc reading time is
too long.
The disc is dirty. Clean the disc by referring to “Maintenance” above.
No sound. The system cord and/or speaker cord is not connected. Check the connection.
The audio cord is not connected to AUX IN (VCR) and/
or DIGITAL IN (DBS) correctly.
Connect the cord correctly. (See page 13.)
An incorrect source has been selected. Select the correct source. (See page 17.)
No picture is displayed
on the TV screen.
The video cord is not connected correctly. Connect the cord correctly. (See page 12.)
The disc or file is not playable. Use a playable disc or file. (See pages 3 and 4.)
No picture is displayed
on the TV screen, the
picture is blurred, or the
picture is divided into
two parts.
The scan mode is set to “480p” though the center unit is
connected to the TV which does not support the
progressive video input such as a conventional TV.
Change the scan mode to “480i”. (See page 18.)
Video and audio are
distorted.
The disc is scratched or dirty. Replace or clean the disc.
A VCR is connected between the center unit and the
TV.
Connect the center unit and TV directly. (See page 12.)
The picture does not fit
the TV screen.
The monitor type is not set correctly. Set “MONITOR TYPE” properly. (See page 34.)
No picture is displayed
on the TV or no sound
come out through
HDMI connection.
A video or audio format not compatible with this
system and/or TV is played.
Check the video or audio format of the signal to see if it
is compatible with this system and/or TV.
A HDCP-compatible TV is not connected. Connect a HDCP-compatible TV. (See page 12.)
The system failed to recognize the TV connected with
the HDMI cable.
Disconnect the HDMI cable and connect it again.
A HDMI cable longer than 5 m (15 ft) is used. Use a HDMI cable shorter than 5 m (15 ft) to assure
stable operation and picture quality.
The picture is distorted
when the TV is
connected through
HDMI terminal.
Proportion of the picture may not be shown correctly
depending on a disc/file when the TV is connected
through HDMI terminal.
Connect the TV through component video, S-video, or
composite video jacks (see page 12), then set the scan
mode to “480p” (see page 18).
The broadcast is hard to
hear because of noise.
Antennas are disconnected. Reconnect the antennas correctly and securely. (See
page 8.)
References
TH-C60-40[J]-03Body.fm Page 39 Wednesday, April 19, 2006 7:04 PM
Page: 42
40
7 Center unit (XV-THC60/XV-THC50/XV-THC40)
Audio section
Digital input*1
:
DIGITAL IN (DBS): –21 dBm to –15 dBm
(OPTICAL) (660 nm E30 nm)
*1 Corresponding to Linear PCM, Dolby Digital, and DTS Digital
Surround (with sampling frequency — 32 kHz, 44.1 kHz,
48 kHz)
Video section
Video System: NTSC
Horizontal Resolution: 500 lines
Signal-to-Noise Ratio: 64 dB
Video output level
Composite: 1.0 V(p-p)/75 Ω
S-video-Y: 1.0 V(p-p)/75 Ω
S-video-C: 0.286 V(p-p)/75 Ω
Component-Y: 1.0 V(p-p)/75 Ω
Component-PB/PR: 0.7 V(p-p)/75 Ω
Video input sensitivity/Impedance (VCR IN)
Composite: 1.0 V(p-p)/75 Ω
S-video-Y: 1.0 V(p-p)/75 Ω
S-video-C: 0.286 V(p-p)/75 Ω
HDMI
HDMI Output (Ver. 1.0): MONITOR OUT
USB storage
USB specification: Compatible with the USB 2.0 Full-
Speed
Compatible device: Mass Storage Class
Compatible file system: FAT16, FAT32
Bus power supply: Max. 500 mA
Tuner section
Tuning Range
FM: 87.5 MHz to 108.0 MHz
AM: 530 kHz to 1 710 kHz
General
Power Requirements: AC 120 V , 60 Hz
Power Consumption: 25 W (at operation)
0.6 W (in standby mode)
Dimensions (W M H M D):
400 mm M 85 mm M 316 mm
(15-3/4 inches M 3-3/8 inches M
12-1/2 inches)
Mass: 3.8 kg (8.4 lbs)
7 Subwoofer (SP-PWC60/SP-PWC50)
Amplifier section
Front/Center/Surround: 200 W per channel, RMS at 3 Ω at
1 kHz, with 10 % total harmonic
distortion.
Subwoofer: 200 W, RMS at 3 Ω at 100 Hz, with
10 % total harmonic distortion.
Speaker section
Speaker unit: 16 cm (6-5/16 inches) Bass-reflex
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 30 Hz to 200 Hz
Sound Pressure Level: 74 dB/W·m
General
Power Requirements: AC 120 V , 60 Hz
Power Consumption: 180 W (at operation)
0 W (in standby mode)
Dimensions (W M H M D):
171 mm M 411 mm M 458 mm
(6-3/4 inches M 16-3/16 inches M 18-
1/16 inches)
Mass: 12.3 kg (27.2 lbs)
Specifications
References
TH-C60-40[J]rev-4.book Page 40 Tuesday, April 18, 2006 2:16 PM
Page: 43
41
7 Subwoofer (SP-PWC40)
Amplifier section
Front/Center/Surround: 167 W per channel, RMS at 3 Ω at
1 kHz, with 10 % total harmonic
distortion.
Subwoofer: 167 W, RMS at 3 Ω at 100 Hz, with
10 % total harmonic distortion.
Speaker section
Speaker unit: 16 cm (6-5/16 inches) Bass-reflex
Power Handling Capacity: 170 W
Impedance: 3 Ω
Frequency Range: 30 Hz to 200 Hz
Sound Pressure Level: 73 dB/W·m
General
Power Requirements: AC 120 V , 60 Hz
Power Consumption: 160 W (at operation)
0 W (in standby mode)
Dimensions (W M H M D):
170 mm M 411 mm M 458 mm
(6-3/4 inches M 16-3/16 inches M 18-
1/16 inches)
Mass: 11.5 kg (25.4 lbs)
7 Satellite Speakers — SP-XTHC60
Front speakers (SP-THC60F)
Type: 1-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 5.5 cm (2-3/16 inches) cone M 2
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 100 Hz to 20 000 Hz
Sound Pressure Level: 78 dB/W·m
Dimensions (W M H M D):
280 mm M 1 106 mm M 280 mm
(11-1/16 inches M 43-9/16 inches M
11-1/16 inches)
Mass: 3.3 kg (7.3 lbs) each
Center speaker (SP-THC60C)
Type: 1-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 6.5 cm (2-9/16 inches) cone M 2
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 90 Hz to 20 000 Hz
Sound Pressure Level: 81 dB/W·m
Dimensions (W M H M D):
250 mm M 85 mm M 91 mm
(9-7/8 inches M 3-3/8 inches M 3-5/
8 inches)
Mass: 0.8 kg (1.8 lbs)
Surround speakers (SP-THC60S)
Type: 2-way 3-speaker Bass reflex type
Speaker: 5.5 cm (2-3/16 inches) cone M 2
3.0 cm (1-3/16 inches) dome M 1
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 100 Hz to 20 000 Hz
Sound Pressure Level: 78 dB/W·m
Dimensions (W M H M D):
280 mm M 1 114 mm M 280 mm
(11-1/16 inches M 43-7/8 inches M
11-1/16 inches)
Mass: 3.4 kg (7.5 lbs) each
References
TH-C60-40[J]rev-4.book Page 41 Tuesday, April 18, 2006 2:16 PM
Page: 44
42
7 Satellite Speakers— SP-XTHC50
Front speakers (SP-THC60F)
Type: 1-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 5.5 cm (2-3/16 inches) cone M 2
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 100 Hz to 20 000 Hz
Sound Pressure Level: 78 dB/W·m
Dimensions (W M H M D):
280 mm M 1 106 mm M 280 mm
(11-1/16 inches M 43-9/16 inches M
11-1/16 inches)
Mass: 3.3 kg (7.3 lbs) each
Center speaker (SP-THC60C)
Type: 1-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 6.5 cm (2-9/16 inches) cone M 2
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 90 Hz to 20 000 Hz
Sound Pressure Level: 81 dB/W·m
Dimensions (W M H M D):
250 mm M 85 mm M 91 mm
(9-7/8 inches M 3-3/8 inches M 3-5/
8 inches)
Mass: 0.8 kg (1.8 lbs)
Surround speakers (SP-THC50S)
Type: 1-way Bass reflex type
Speaker: 8.0 cm (3-3/16 inches) cone M 1
Power Handling Capacity: 200 W
Impedance: 3 Ω
Frequency Range: 80 Hz to 20 000 Hz
Sound Pressure Level: 70 dB/W·m
Dimensions (W M H M D):
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M 4-1/
4 inches)
Mass: 0.44 kg (0.98 lbs) each
7 Satellite Speakers — SP-XTHC40
Front speakers (SP-THC40F)
Type: 2-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 8.0 cm (3-3/16 inches) cone M 1
1.5 cm (5/8 inches) dome M 1
Power Handling Capacity: 170 W
Impedance: 3 Ω
Frequency Range: 80 Hz to 20 000 Hz
Sound Pressure Level: 77 dB/W·m
Dimensions (W M H M D):
104.5 mm M 139 mm M 101 mm
(4-1/8 inches M 5-1/2 inches M
4 inches)
Mass: 0.56 kg (1.3 lbs) each
Center speaker (SP-THC40C)
Type: 2-way 2-speaker Bass reflex type
(Magnetically shielded Type)
Speaker: 8.0 cm (3-3/16 inches) cone M 1
1.5 cm (5/8 inches) dome M 1
Power Handling Capacity: 170 W
Impedance: 3 Ω
Frequency Range: 80 Hz to 20 000 Hz
Sound Pressure Level: 77 dB/W·m
Dimensions (W M H M D):
137 mm M 105 mm M 104.5 mm
(5-7/16 inches M 4-3/16 inches M 4-
1/8 inches)
Mass: 0.57 kg (1.3 lbs)
Surround speakers (SP-THC40S)
Type: 1-way Bass reflex type
Speaker: 8.0 cm (3-3/16 inches) cone M 1
Power Handling Capacity: 170 W
Impedance: 3 Ω
Frequency Range: 80 Hz to 20 000 Hz
Sound Pressure Level: 70 dB/W·m
Dimensions (W M H M D):
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M 4-1/
4 inches)
Mass: 0.56 kg (1.3 lbs) each
Designs & specifications are subject to change without notice.
• HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
• HDCP is the abbreviation of “High-Bandwidth Digital Content
Protection,” and is the high-reliable copy control technology
licensed by Digital Content Protection, LLC.
References
TH-C60-40[J]rev-4.book Page 42 Tuesday, April 18, 2006 2:16 PM
Page: 45
43
TH-C60-40[J]rev-4.book Page 43 Tuesday, April 18, 2006 2:16 PM
Page: 46
44
TH-C60-40[J]rev-4.book Page 44 Tuesday, April 18, 2006 2:16 PM
Page: 47
EN
0206RYMMDWJSC
© 2006 Victor Company of Japan, Limited
TH-C60/TH-C50/TH-C40
DVD
DIGITAL
THEATER
SYSTEM
TH-C60-40[J]rev-4.book Page 45 Tuesday, April 18, 2006 2:16 PM

Question & answers

There are no questions about the JVC TH-C50 yet.

Ask a question about the JVC TH-C50

Have a question about the JVC TH-C50 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC TH-C50. Please make sure that you describe your difficulty with the JVC TH-C50 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.