View a manual of the JVC RA-P11 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
CAUTION • Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) • Do not place any naked flame sources, such as lighted candles, on the apparatus. • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. • Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. • Rating label is placed on the exterior of the bottom. Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of Victor Company of Japan, Limited is: JVC Technology Centre Europe GmbH P.O. Box 10 05 52 61145 Friedberg Germany PORTABLE AUDIO SYSTEM RA-P10 LVT1634-004A [B] ©2006 Victor Company of Japan, Limited 0906NSMCREBET Warnings, Cautions and Others Caution: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: Front: No obstructions and open spacing. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more. 15cm 15cm 15cm 15cm 15cm 10cm Front Side Getting Started Warning • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these things may cause the battery to give off heat, crack, or start a fire. • Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat, crack, or start a fire. • When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to give off heat, crack, or start a fire. • Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat, crack, or start a fire. • Dispose of battery in the proper manner, according to federal, state, and local regulations. • The batteries (battery pack or batteries installed ) shall not be exposed to excessive heat source such as sunshine, fire or the like. Operating on the Remote Control Supplied Accessories After unpacking, check to be sure that you have all the following items. • Remote control • AC adaptor • Attachments (6 types) • Rubber pads (A type×2, B type×2) • CR2025 (×2) lithium coin batteries One is loaded on the remote control at the factory. Prepare the Remote Control • When you use the remote control for the first time, pull out the insulation sheet. Replacing the Battery in the Remote Control • Insert the battery into the remote control by matching the polarity (+ and –) correctly. Insulation sheet Lithium coin battery (CR2025) Preparation of the Unit 9V 1.5A Loading batteries for the Clock Be sure to match the poles (+/-) correctly. Lithium coin battery (CR2025) (supplied) FM wire antenna (Pass through the notch in the cover) AC adaptor: AA-R9030 (supplied) To a wall outlet Plug the AC adaptor only after all connections are completed. 1 SOURCE button Switch the sound source. 2 FM MODE button Switch FM stereo/monaural. 3 MUTING button Turn off the sound. Return to original mode by pressing again. 4 PRESET +/- button Select a registered FM radio station (P01 to 20). 5 iPod 6 button Play/pause the iPod. 6 button Switch the backlight on/off. 7 4/¢ button Fast-forward/rewind the iPod song. Change frequencies to tune in to FM radio station. 8 VOLUME +/- button You can adjust the volume level from 00 to a maximum of 20. Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. In These Cases Check the following points Power does not come on. • AC adaptor is not inserted securely. Plug in securely. • The batteries are exhausted. No longer works. Press the “RESET” button (see “Resetting the unit”). Cannot set the iPod. • Is the selected attachment compatible to your iPod? Confirm the compatibility of iPod and attachments in “iPod Compatibility Chart”. • Is the attachment properly mounted on the unit? Make sure to mount the attachment properly. Cannot operate iPod. • Is the iPod firmly connected to the connector plug of the unit? • Is the iPod properly functioning? Test the iPod functions in stand alone condition. iPod cannot be charged. • Is the iPod firmly connected to the connector plug of the unit? • Is the AC adaptor connected? The iPod cannot be charged while the Unit is operated on batteries. • For iPod 3rd Generation, set the “CHARGING SWITCH” to “FIREWIRE” (see “Charging the iPod”). Hard to listen to broadcasts because of noise. The FM antenna is not properly extended and positioned. Unable to operate the System from the remote control. • The path between the remote control and the remote sensor on the System is blocked. • The batteries are exhausted. When the volume level is manually set higher than “08”, the unit automatically lowers the level to “08”. The unit’s battery runs low (The “---” (Low battery) appears on the display). Replace the batteries with new ones. Resetting the unit If “Troubleshooting” does not eliminate malfunctioning (failure to operate or display properly, etc.), press the “RESET” button on the rear of the unit with something having a sharp point, while the unit is turned on. After pressing “RESET” button, unplug the AC adaptor and wait a while before plugging it again. • When using “RESET” button, make sure the lithium coin battery is loaded. • While resetting the unit, the clock is also reset. Adjust the clock after resetting the unit. Specifications Model RA-P10 Type Portable audio system Amplifier Power Output 4W x 2 1kHz 10% THD, 6Ω (IEC268-3) Input Sensitivity/ Impedance AUX Input 250mV/47kΩ FM Tuner Tuning Range 87.50MHz - 108.00MHz Frequency Step 50kHz Preset Stations 20 Speaker 1way full range, diameter 35mm x2 Input Terminal External DC IN ( for AC adaptor) AUX IN (mini jack) Power Source DC9V 1.5A (EXTERNAL DC IN) DC9V (SIZE R6, AA BATTERY OR EQUIVALENT x6) DC3V (CR2025, for the clock) AC adaptor Input : AC 110-240V , 50/60Hz Output : DC 9V 1.5A Dimensions (W x H x D) (W) 331 mm x (H) 71 mm x (D) 98 mm Weight (Without batteries) 0.7kg Accessory See Supplied Accessories Specifications and appearance are subject to change without prior notice. 1 2 3 4 5 6 7 8 INSTRUCTIONS EN Open the battery compartment cover by pressing the small tab. Loading batteries for the Unit (The battery power supply) Close the cover in the order shown by the numbers. R6 (SUM-3)/AA (15F) (not supplied) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Connecting the AC adaptor Insert three batteries to each compartment (six batteries total). Be sure to match the poles (+/-) correctly. While the AC adaptor is connected to the wall outlet, the unit works without batteries. Press the tab to open the cover. Close the cover in the order shown by the numbers. CAUTION: To avoid risk of fire, and to prevent damage. • Do not use AC adaptors except for the supplied AC adaptor. • Do not use the supplied AC adaptor for other equipment. (Front side) (Rear side) NOTES • Point the remote control at the remote control sensor on the front panel. • The remote control sensor is designed to receive signals from up to approximately 7 m distance when the remote control is pointed directly. If the remote control is pointed with an angle, the distance may become shorter. Precautions • Install in a place which is level, dry and neither too hot nor too cold–between 5°C and 35°C. • Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System. • Leave sufficient distance between the System and the TV. • Keep the speakers away from the TV to avoid interference with TV. DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration. SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Do read the operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections. Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. Do be careful with glass panels or doors on equipment. DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way—switch off, withdraw the mains plug and consult your dealer. DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people. DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving. DON’T listen to headphones at high volume as such use can permanently damage your hearing. DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten the life of the equipment. DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions. DON’T allow electrical equipment to be exposed to rain or moisture. ABOVE ALL – NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case —this could result in a fatal electrical shock.; – NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry! 9V 1.5A RA-P10-B_EN.indd 1 RA-P10-B_EN.indd 1 10/3/2006 11:53:55 AM 10/3/2006 11:53:55 AM
Basic and Common Operations Press Functions • Light the display screen for 5 seconds when the power is turned off. • Temporarily stop the alarm sound when the alarm is ringing (SNOOZE). (see “Stopping alarm sound”) See “How to set the time and use the alarm” Turn on or off the power Press Functions Turns on or off the power When the power is turned off at volume level “15” or higher, the unit automatically sets the volume level to “14” the next time it is turned on. Adjust the volume Press Functions Adjust the volume level from 00 to a maximum of 20. –: Turn down the volume. +: Turn up the volume. Display Information Date Day of the week Temperature Current time/ alarm time Explanation of Icons Off: current time / On: alarm time Off: alarm off / On: alarm on / Blinking: alarm sounding (When “TIMER PLAY” is set) Blinks while snoozing (the alarm is paused) Sound source indicator iPod/FM/AUX (blinks while muted) When adjusting the volume 00 - 20 When FM radio is selected P01 - P20 (channel) / 87.50 - 108.00 MHz (frequency) When the source is set to iPod and the alarm is set to TIMER PLAY iPod (slow blinking) When the source is set to FM radio and the alarm is set to TIMER PLAY 87.50 - 108.00 MHz ↔ P01-P20 When battery power is low - - - When trying to set alarm to TIMER PLAY while selecting AUX How to set the time and use the alarm Switch/Press Functions Switch the alarm on/off. OFF: turn off the alarm (BUZZER/ TIMER PLAY). BUZZER: alarm on (buzzer sound) TIMER PLAY: alarm on (iPod/FM radio) • Switch between current time and alarm time. • Press and hold this button to select the current time/alarm time setting mode. Change the values for the time setting. Setting the Clock 1 Switch to current time display with the “SET” button. 2 Press and hold the “SET” button. → The year display starts flashing. 3 While flashing, set each item with the “DOWN”/“UP” buttons. 4 Press the SET button. • When the “SET” button is pressed, the flashing items will change in the following order. • The time is set when switching to time display from Minutes. NOTES • The time can be set both when the power is on and off. • To modify the setting, start again from step 1. Setting the alarm (ALARM-BUZZER) 1 Switch to alarm time display with the “SET” button. → “ALARM” icon appears on the display. 2 Press and hold the “SET” button. → The hour display starts flashing. 3 While flashing, set each item with the “DOWN”/“UP” buttons. • When the “SET” button is pressed, the flashing items will change in the following order. • It is not necessary to set the “TIMER PLAY” time at this point. 4 Switch the “ALARM” switch to “BUZZER”. • To check the set time, switch the display to alarm time by pressing the “SET” button. • The buzzer sounds for three minutes. Selecting iPod or FM radio for the alarm sound (ALARM-TIMER PLAY) 1 Set the alarm time. (See steps 1 to 3 of “To set the alarm (ALARM-BUZZER)”) • You can set the duration of time between timer-on and timer-off from 10 minutes to 30 minutes in TIMER PLAY time. 2 If the power is off, turn the unit power on. 3 Confirm that you can hear the iPod or FM radio. • Set to an appropriate volume. 4 Switch the “ALARM” switch to “TIMER PLAY”. The selected source is blinking on the display. Stopping alarm sound To pause the alarm (snooze) Press the “SNOOZE/LIGHT” button while the alarm in sounding, when the alarm is set with either “ALARM-BUZZER” or “ALARM-TIMER PLAY”. The alarm sound is temporarily stopped, and started again 5 minutes later. You can repeat this up to 10 times. To stop the alarm (BUZZER/ TIMER PLAY) • Switch the “ALARM” switch to “OFF”. Playing back from other equipment Connecting other equipment Connect an external device to the AUX jack on the rear of the unit using a stereo mini plug cord (not supplied) . NOTE • Always set volume to the minimum level when connecting or disconnecting the other equipment. Listening to external devices 1 Turn the unit power on. 2 Select “AUX” with the “SOURCE” button. 3 Start playback on the external device. 4 Adjust the volume. To audio output such as CD/ MD/digital audio player, etc. Playing back from iPod Setting the iPod on the unit 1 Select the attachment compatible to your iPod (see “iPod Compatibility Chart”). 2 Match the attachment tab to the hole in the unit, and insert the attachment to the unit. 3 Connect the iPod to the connector plug of the unit. • Always set volume to the minimum level when connecting or disconnecting iPod. • When you connect your iPod to the unit, make sure you insert it all the way. • When disconnecting the iPod, make sure that the System is turned off. Listening to the iPod 1 Connect the iPod to the unit. 2 Turn the unit power on. 3 Select “iPod” with the “SOURCE” button. When iPod is selected as sound source, it automatically starts playback. Press Functions Unit Remote control 6 Playback/Pause Press and hold this button to switch the iPod to sleep mode. ¢ Next song / fast forward (press and hold) 4 Previous song (Press this button during playback to jump back to the beginning of the track.) / fast rewind (press and hold) Charging the iPod The iPod is charged while it is set on the unit when the Unit power is on. • Connect the AC adaptor to the Unit. The iPod battery is not charged while the Unit is operated on the battery power supply. • The iPod is charged regardless of the sound source selected on the Unit. • See the iPod instruction manual about charging times. • The “CHARGING SWITCH” is located inside of battery compartment on the rear of the Unit. Set the “CHARGING SWITCH” to “FIREWIRE” for 10GB/15GB/20GB/ 30GB/40GB iPod 3rd Generation. For all other models, you can set the switch to either “FIREWIRE” or “USB” to charge the iPod. iPod Compatibility Chart iPod model 4 GB mini 1st Generation 4 GB mini 2nd Generation 6 GB mini 2nd Generation iPod nano 1GB/2GB/4GB iPod nano 2nd Generation 2GB/4GB/8GB iPod video 5th Generation 30GB iPod video 5th Generation 60GB/80GB Attachment names mini nano 2G nano VIDEO 30GB VIDEO 60GB iPod model iPod 3rd Generation 10GB/15GB/20GB iPod 4th Generation 20GB iPod photo 4th Generation 20GB/30GB iPod 3rd Generation 30GB/40GB iPod 4th Generation 40GB iPod photo 4th Generation 40GB/60GB Rubber pad A type (Large) B type(Small) Attachment name iPod Combine this attachment with the rubber pads. Select the rubber pad size which matches your iPod model. • Select the appropriate attachment for your iPod model. Listening to FM Broadcasts Press Functions Unit Remote control FM MODE/ Switch FM stereo/monaural. When there is too much static in an FM stereo broadcast, you can reduce the static by switching to monaural reception. Press again to switch back to stereo reception. If the broadcast is not FM stereo, the sound becomes monaural, even if FM stereo is selected. 6 — • Switch channel display / frequency display. Channel display is automatically switched to frequency display after approx. 3 seconds. • To register a channel, press and hold this button. (see “Presetting Stations”) ¢ 4 Select a channel from P01 to P20. (The unit button can be used when channel display is selected.) ¢ 4 Change frequencies to tune in to FM radio station. (The unit button can be used when frequency display is selected.) • Press and hold to search broadcast stations automatically. The search is finished when the signal is received. Press again while searching to quit search. Listening to FM radio Stretch out the wire antenna located on the rear of the unit before using. 1 Turn the Unit power on. 2 Select “FM” with the “SOURCE” button. 3 Select a station with the “4”/“¢” button. Presetting Stations 1 Select “FM” with the “SOURCE” button, and switch to channel display with “6” button. 2 Use the “4”/“¢” button to select the channel number (P01 to P20) to be registered. 3 Press and hold the “6” button. → The channel number starts flashing. 4 Use the “4”/“¢” button to select the frequency (87.50 MHz to 108.00 MHz) of the station that you wish to register. 5 Press the “6” button → The selected frequency will be registered. • To confirm registration, select the registered channel number (P01 to P20), and press “6” button to display frequency. Channel display Frequency display Year → Month → Day → 12/24-hour time → Hour → Min. → time display NOTES • The connector plug is protected with a cover when it is first purchased. Please remove the cover before operating the unit. • Do not carry the System with iPod connected. You might drop it down or it might cause damages to the connector part. • Do not touch or hit the iPod terminal pins or the connector pins directly. It might cause damages to the connector part. • If the iPod does not play correctly, please update your iPod software to the latest version. - For details about updating your iPod, check on the Apple web site <http://www.apple.com>. • iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. • JVC is not responsible for any loss of or damage to iPod that might result from the use of this product. • Sound distortion may occur when playing back audio sources with high recording levels. When distortion occurs, it is recommended to turn off the equalizer of the iPod. For information on operating the iPod, see the iPod instruction manual. How to combine the rubber pads with the attachment There are two types of rubber pad : “A type (Large)” and “B type (Small)”. Select the appropriate rubber pads for your iPod model. Insert the rubber pads narrow-end first. A type (Large) B type(Small) Attachment name CHARGING SWITCH Press Functions FM MODE/ • Switch on/off the backlight when the button is held down. • Switch FM stereo/monaural when FM is selected. ¢ 4 6 (see “Playing back from iPod” and “Listening to FM Broadcasts”) Select a source Press Functions Select a source iPod → FM → AUX “STEREO” is displayed when an FM stereo broadcast is received. “MONO” is displayed when the monaural is selected. (see “Listening to FM Broadcasts ”) Current time: Blinking / Other Clock Display: Lighting Hour → Min. → TIMER PLAY time (10 to 30) → time display Hour → Min. → TIMER PLAY time (10 to 30) → time display Press Functions Switch the temperature display between Celsius/ Fahrenheit. Remote control sensor iPod connector plug CAUTION: • “AUX” cannot be selected as a source. Select another source. • The “TIMER PLAY” does not work when the Unit power is turned off. RA-P10-B_EN.indd 2 RA-P10-B_EN.indd 2 10/3/2006 11:54:17 AM 10/3/2006 11:54:17 AM
Have a question about the JVC RA-P11 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC RA-P11. Please make sure that you describe your difficulty with the JVC RA-P11 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.