View a manual of the JVC DT-E21L4U below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
LCT2673-001A For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. Serial No. : DT-E21L4 / DT-E17L4G : MULTI FORMAT LCD MONITOR INSTRUCTIONS The illustration of the monitor is of DT-E21L4. DT-E21L4 DT-E17L4G ®
2 Safety Precautions WARNING:TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. IMPORTANT SAFEGUARDS Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use, and service. Please read these “IMPORTANT SAFEGUARDS” carefully before use. All the safety and operating instructions should be read before the • product is operated. The safety and operating instructions should be retained for future • reference. All warnings on the product and in the operating instructions • should be adhered to. All operating instructions should be followed. • POWER CONNECTION The power supply voltage rating of this product is AC 120 V. The power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure safety and EMC regulations of each country. Not all types of power cords are supplied to this product. For U.S.A. and Canada: AC 120 V This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug. This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply of your home, consult your product dealer or local electric power company. Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Before connecting other products such as VCR’s and personal • computers, you should turn off the power of this product for protection against electric shock. Do not use attachments not recommended by the • manufacturer as they may be hazardous. When replacement parts are required, • be sure the service technician has used replacement parts specified by the manufacturer or equivalents. Unauthorized substitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repairs to this product, • ask the service technician to perform safety checks to determine that the product is in proper operating condition. Under the following conditions, 1. Turn off the power. 2. Unplug this product from the wall outlet. 3. Refer service to qualified service personnel. a) When the product emits smoke or unusual smell. b) When the product exhibits a distinct change in performance —for example, no picture or no sound. c) If liquid has been spilled, or objects have fallen on the product. d) If the product has been exposed to rain or water. e) If the product has been dropped or damaged in any way. f) When the power supply cord or plug is damaged. Do not install this product in the following places: • in a damp or dusty room – where the product is exposed to soot or steam, such as – near the cooking counter or a humidifier near heat sources – where condensation easily occurs, such as near the window – in a location exposed to direct sunlight or strong light – Do not place this product on an unstable cart, stand, or table. • The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer. Do not use this product near water. • Be sure to install the product in the place where proper • temperature and humidity are kept (☞ “Operating conditions” on page 27). This product becomes hot during its use. Take enough care when handling the product. CAUTION: To reduce the risk of electric shock. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. RISK OF ELECTRICAL SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION
3 Do not use the product for a long time if the sound is distorted. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel. Use only the power source specified on the unit. AC power: 120 V, 50 Hz/60 Hz • DC power: 12 V — 17 V • The AC power supply is controlled by turning on/off the POWER • switch on the rear panel. If the product is installed in a place where you cannot easily turn on/off the POWER switch, control the AC power supply by plugging/unplugging the power cord into/from the AC outlet. In this case, install the product as close to the AC outlet as possible, and leave enough space for plugging/unplugging the power cord. If the product is installed in a place where you cannot easily plug/unplug the power cord, equip an easily accessible device to the wiring of the building for turning on/off the power. When the product is left unattended and unused for a long • period of time, unplug it from the wall outlet and disconnect the cable system. Do not overload wall outlets, extension cords, or convenience • receptacles on other equipment as this can result in a risk of fire or electric shock. Use only the accessory cord designed for this product to • prevent shock. Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from • overheating. These openings must not be blocked or covered. Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts, • which could result in a fire or electric shock. Never spill liquid of any kind on the product. • Never place anything on the product. (Placing liquids, naked flames, cloths, paper, etc. on the product may cause a fire.) • Do not apply any strong shock to the LCD panel. (Do not hit any object against it or push it with a sharp-pointed tool.) • Do not put heavy objects on the product. • Do not step on or hang on the product. • FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. WARNING To prevent injury by accidental falll Fix the monitor to a wall by using strings. Fixing the monitor Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a wall or a pillar using durable string. Hook and screw (M4 x 10 mm) (not provided) Hook (not provided) VESA mounting holes The illustration of the monitor is of DT-E21L4.
4 Caution for use of the product for many hours In the case that you use the monitor for many hours, we recommend that you set “No Sync Action” in “Sync Function” to “Power Save” in Main Menu. This will reduce power consumption and relieve strain on the monitor. To reduce damage to the LCD panel, using the LCD Saver function is recommended. Caution for use of the product in the high temperature Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may be damaged. This product is equipped with a temperature sensor to give warning if the temperature becomes too high. If the temperature exceeds the range of normal use, “Temp. Over” is displayed, and the power is turned off automatically if the temperature becomes any higher. In this case, move the product to a place of low temperature to let it cool down. Maintenance Unplug this product from the wall outlet before cleaning. Screen To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be careful about the following: ● Do not paste or stick anything using any glues or adhesive tapes. ● Do not write anything on the screen. ● Do not strike the screen with a hard object. ● Avoid condensation on the screen. ● Do not wipe the screen with any liquid such as water. In addition, wiping the screen with water-diluted neutral detergent or solvent such as alcohol, thinner, or benzine may affect the anti-reflection treatment of the screen. ● Do not wipe the screen forcefully. Wipe stains off the screen with a soft cloth. If the screen gets heavily stained, wipe it with a soft cloth soaked in water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth. Cabinet To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the following: ● Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine. ● Do not expose the cabinet to any volatile substance such as insecticides. ● Do not allow any rubber or plastic in contact for a long time. ● Do not wipe the cabinet forcefully. Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth. Ventilation openings Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control and cause damage to the product. Safety Precautions (cont.) The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display may occur. It is recommended that you change images occasionally, activate the power saving function, or often turn off the power to reduce the load on the LCD panel. Continuous operations of the LCD panel may accelerate the deterioration. Operating Precautions IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.
5 Table of Contents Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT SAFEGUARDS 2 Operating Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caution for use of the product for many hours 4 Caution for use of the product in the high temperature 4 Maintenance 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Rear panel 8 Daily Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Front panel 10 Menu Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 The operation procedure 12 Menu Transition Diagram 13 Main Menu 14 Set-Up Menu 17 External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 About the external control 22 Using the Make/Trigger system 22 Using the serial communication 23 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Self-check program 26 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 General 27 LCD panel 27 Input/output terminals 27 Dimensions 28 Available signals 29
6 Installation ● To install the monitor on a shelf or any other suitable surface using screws You can install the monitor without protruding the stand bottom plate by moving the stand bottom plate to the rear position. CAUTION ● Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged. ● After moving the stand bottom plate to the rear position, be sure to attach the stand with commercially available screws. 1 Loosen the stand screws on the stand support and remove the bottom plate. Bottom plate Stand support 2 Temporarily set the stand screws to screw holes “3” on the right and left sides of the stand support. ● Tighten the temporarily set stand screws so that they protrude from the screw holes by about 4 mm. Screw holes “3” 3 Hook right and left recesses “A” onto the temporarily set screws in the stand support. Recesses “A” 4 Adjust the position so that the screw holes on the stand support align with right and left screw holes “C” and “E” on the bottom plate, tighten the two stand screws on one side (four screws on both sides), and finally retighten the temporarily set screws to lock the stand support and the bottom plate. Screw holes “C” and “E” 5 Use no less than two commercially available screws (no less than four screws on both sides) for the screw holes (10 – φ8) on the stand bottom plate, to anchor the monitor. (Use screws having enough holding strength and resistance against external force of expected vibrations.) 10 – φ8 CAUTION ● It is very dangerous not to anchor the stand with screws as this may cause not only breakage due to the monitor falling or dropping, but also injury or electrical shock. ● To detach the stand CAUTION ● Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged. Screw holes for stand attachment Attachment screws Monitor Stand body ● To install the stand When attaching the stand to the monitor, insert the guides of the stand into the guide holes on the monitor to place the stand in the correct position. Then fix the stand firmly with the attachment screws. Screw holes for stand attachment Stand body Guides Guide holes Stand support Monitor ● Do not rest your arm on the monitor or lean against the monitor. ● Do not touch the LCD panel when installing the monitor. ● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. The illustration of the monitor is of DT-E21L4.
7 ● To install the monitor on a wall You can install the monitor on a wall by changing how the stand bottom plate is attached. Installation Only for Authorized Service Personnel Consult authorized service personnel for the installation of this unit. Installation instructions must be followed precisely in order to prevent accidents. We are selling this product with the understanding that it will be assembled and installed by properly trained and qualified service personnel. About Accidents/Damages We are not liable for any damage caused by faulty assembly, faulty wall mounting, insecure wall mounting, misuse, alterations, or natural disasters. ● Please be aware that screw holes and anchor bolts will remain in the wall surface if the monitor is removed after having been mounted to the wall. Long-term use of the LCD display monitor may result in discoloration of the wall surface due to heat/air emitted by the display. Danger ● Consult authorized service personnel for the installation and attachment of this unit to the wall. Do not attempt to mount the unit by yourself. Improper assembly or installation may cause the unit to fall when it is mounted, which may result in fatal accidents. To prevent this happening, check the strength of the materials in the mounting surface. Check the material strength again after mounting as well. Warning ● Using a monitor other than this product may result in damage or bodily injury due to the LCD display monitor toppling over. ● Assemble all screws securely. Failure to do so may result in the LCD monitor and stand falling down, potentially causing damage or bodily injury. ● This unit does not come with anchor bolts for securing it to walls, etc. Be sure you have materials on hand as appropriate for the mounting location. ● The monitor should be mounted to a wall that can adequately hold the total weight of the monitor and stand over a long period of time and which can adequately withstand earthquakes, conceivable vibrations, and other external forces. ● Mounting On Wooden Walls The weight of the unit should be borne by the wall posts or studs, and these should be reinforced if insufficiently strong. Do not install the Wall Mounting Unit on walls made of plasterboard or thin plywood. Use the commercially sold screws best suited for the wall structure and material. ● Mounting On Concrete Walls Use commercially sold wall anchors capable of supporting the weight of the LCD monitor. ● Do not install the Wall Mounting Unit near the blower or air inlet of an air conditioner. ● Do not install the Wall Mounting Unit in a location subject to frequent vibration, impact or other external forces. ● Do not install the unit in a location where people may hang on it or lean against it. ● Do not block the ventilation holes. ● Do not install the monitor on a non-vertical wall. Caution ● Consult authorized service personnel for electrical work. Using power cords damaged during installation (i.e., exposed or severed wiring) may result in fire or electric shock. ● Conduct the work with adequate working space. Damage or bodily injury may result from working under unsuitable conditions. ● Avoid mounting this unit in areas where there is electrical wiring or water pipes, as fire or electric shock may result. 1 Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged. Loosen the stand screws on the stand support and remove the bottom plate. 2 Temporarily set the stand screws in screw holes “2” and “4” on the right and left sides of the stand support. ● Tighten the temporarily set stand screws so that they protrude from the screw holes by about 4 mm. 3 Tighten commercially available screws in the 6 holes shown in the figure below to install the monitor on the wall. 4 Hook the temporarily set screws on the stand support in right and left recesses “A” and “B” on the bottom plate, tighten the two stand screws in right and left screw holes “D” and finally retighten the temporarily set screws to lock the stand support and bottom plate. Bottom plate Stand support Stand screws “2” and “4” Recesses “A” and “B” Screw holes “D”
8 1 POWER switch Turns AC power on or off. ● You need to press button (☞ u on page 10) to use the monitor after turning on the POWER switch. 2 AC IN terminal AC power input connector. Connect the provided AC power cord to an AC outlet. ● Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞ “Attaching the power cord holder” on page 9). CAUTION Do not connect the power cord until all other connections are completed. 3 REMOTE terminal Terminal for controlling the monitor by an external control (☞ “External Control” on page 22). 4 VIDEO terminals (BNC) Input (IN) and output (OUT) terminals for the composite signals. 5 AUDIO (IN) terminals (pin jack, stereo minijack) Input terminals for the analog audio signals. ● Use this terminal for the analog audio connection of the SDI. When a superimposed signal (EMBEDDED AUDIO signal on an SDI signal) is input, analog audio signals cannot be input. ● Use these terminals when inputting HDMI analog audio signals. ● If there is no audio signal for HDMI (e.g. DVI signals have been changed to HDMI signals), input audio signals into this terminal. When inputting audio into this terminal, set “Audio1 Assign” or “Audio2 Assign” of the menu to “HDMI-Analog”. (☞ page 16) 6 AUDIO (MONITOR OUT) terminals (pin jack) Output terminals for the analog audio signal. ● The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI (IN 1 or IN 2) input terminal. ● The signal is output from this terminal only when the monitor is on or in “Power Save” (power save) mode (☞ “No Sync Action” on page 17). ● The EMBEDDED AUDIO signal... is decoded into an analog signal, then emitted. – is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI (IN 1 or IN 2) – terminal. ● Audio signals are only output from the HDMI terminal when the signals are not protected by HDCP. Even when the signals are protected by HDCP, sound is emitted from the speakers. – 7 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC) Input terminals for the HD/SD SDI signals. ● The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz. Rear panel Connections Security slot Attach a security wire to this slot. The illustration of the monitor is of DT-E21L4. Carry handle Use this handle when carrying the monitor.
9 8 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC) Output terminal for the HD/SD SDI signals. ● The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted. ● When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal. ● The signals are emitted from this terminal only when the monitor is on or in “Power Save” (power save) mode. 9 HDMI terminal Input terminal compatible with HDCP for the HDMI signal. (☞ page 29) p COMPO./RGB terminal (mini D-sub 15pin) Input terminal for the analog component signal or analog RGB signal. ● Set “Component/RGB Select” appropriately for input signals. (☞ page 15) q DC switch Turns the DC 12 V power on or off. ● You need to press button (☞ u on page 10) on the front panel to turn on the monitor after turning on the DC switch. ● The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off the DC switch. w DC IN 12 V terminal DC 12 V (maximum DC 17 V) power input connector. ● While using both the AC and DC 12 V power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example, when turning off the POWER switch), the power supply automatically switches to the DC 12 V power supply. ● Use a DC power supply with the LPS (Limited Power Sources) function. e Screw holes for external battery attachment Attach external battery for DC 12 V power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2 or 3 according to the type of external battery. (Depending on the battery type.) Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery. CAUTION ● Do not use the external battery for DC 24 V power supply. ● Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used. Cover 2 AC IN terminal Case 1 CAUTION ● Use only the provided screws. ● Make sure the plug will not be pulled out after the cover is attached to the case. Attaching the power cord holder The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. ● The power cord holder consists of two parts, a case and a cover. To detach the cover 3 Note for connections Before making any connections, turn off all the equipment. • Use a cord whose plugs correctly match the terminals on this monitor and the equipment. • Plugs should be firmly inserted; poor connections could cause noise. • When unplugging a cord, be sure to grasp its plug and pull it out. • DO NOT connect the power cord until all connections are complete. • Refer also to the user manual of each piece of equipment. • When using DC 12 V power (maximum DC 17 V), check the DC IN 12V terminal pin signal, and use the correct polarity. If the polarity is reversed, this could cause a fire or personal injury.
10 Front panel 1 Speakers (stereo) The speakers emit the same audio signal emitted from the AUDIO (MONITOR OUT) terminals. (☞ “ 6 AUDIO terminals” on page 8) 2 Picture adjustment knob PHASE: Adjusts the picture hue. CHROMA: Adjusts the picture color density. BRIGHT: Adjusts the picture brightness. CONTRAST: Adjusts the picture contrast. ● PHASE and CHROMA cannot be adjusted for certain signal formats. ● When “Component Phase” is set to “Disable” and an NTSC signal is input, PHASE can be adjusted (☞ page 18). 3 VOLUME adjustment button/EMBEDDED AUDIO setting button Adjusts the volume when no menu screen is displayed. Selects an audio channel when EMBEDDED AUDIO signals are contained in SDI input. (☞ “Volume Adjustment/Audio Channel Selection” on page 11) 4 MUTING button Turns off the sound when no menu screen is displayed. ● To cancel the function, press the button again. ● Muting function is also canceled when “Balance” of “Audio Setting” in the Main Menu is changed (☞ page 16). 5 / / / buttons When a menu screen is displayed selects or adjusts menu items. (☞ “The operation procedure” on page 12) 6 FUNCTION button Assign functions to the F1 and F2 buttons when the menu is not displayed. (☞ page 21) 7 MENU button Activates/deactivates the display of the Main Menu. (☞ “The operation procedure” on page 12) 8 COLOR OFF button/lamp Displays only the luminance signal. ● This function does not work for RGB input signals. 9 1:1 button/lamp Displays the picture in the original resolution of the input signal. ● The aspect ratio of the picture may change depending on the input signal. p AREA MARKER button/lamp Displays/hides the area marker. ● Select the style of the area marker in “Marker” of the Main Menu (☞ page 15). ● This function works only when displaying the picture in 16:9 aspect ratio. Daily Operations “No Effect” is displayed when you press a button which is not • available for the current input or signal format (the lamp lights even when the function does not actually work). The items controlled by the MAKE system cannot be controlled • by the buttons on the front panel (“Remote On” is displayed and the lamps do not light). Tally lamp This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. You can select the color of the tally lamp from “Green” or “Red.” • You can also select whether the whole lamp is turned on at once, or whether it is turned on one half at a time. (☞ “Tally Setting” in “Set-Up Menu” on page 17 and “External Control” on page 22) The illustration of the monitor is of DT-E21L4. ● This function does not work when “Area Marker” or “R-Area Marker” is set to “Off” in “Marker.” q SAFETY MARKER button/lamp Displays/hides the safety marker. ● Adjust the area of the safety marker in “Marker” of Main Menu (☞ page 15). ● This function will not work when the picture is displayed in 1:1 aspect ratio and “SD 4:3 Size” on the menu is set to “H Full”. ● This function does not work when “Safety Marker” or “R-Safety Marker” is set to “Off” in “Marker.” w SCREENS CHECK button/lamp Displays only the selected element (R, G, or B) of the video signal. ● Each time you press this button, the picture changes in the following order. e T.C. (time code) button/lamp Activates/deactivates the display of the time data (time code) contained in the SDI signal. (☞ “On the Information Display” on page 11) ● Select the time code type in “Information” of Set-Up Menu (☞ page 19). r INPUT SELECT buttons/lamps Selects an input. SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal HDMI: HDMI terminal COMPO./RGB: COMPO./RGB terminal VIDEO: VIDEO terminal ● The lamp for the selected input lights. t F1/F2 buttons/lamps You can use the functions assigned to this button. y Power lamp Unlit: The monitor is completely off (the power switch on the rear panel is turned off). In Low Power Mode (☞ page 20) Lights in Green: The monitor is on. Lights in orange: The monitor is off (on standby). Flashes in orange: The monitor is in the Power Save (power save) mode. (☞ “No Sync Action” in “Sync Function” on page 17) u button Turns on and off (on standby) the monitor. ● The power switch is equipped on the rear panel of the monitor (☞ 1 on page 8). RGB (Normal screen) Red screen Blue screen Green screen
11 i DC lamp When the DC 12 V power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the voltage becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red. ● Make sure to turn off the POWER switch and DC switch on the rear panel before replacing the battery. ● The length of time that the lamp lights in orange differs depending on the type of battery or the battery condition. It is recommended to replace the battery when the lamp turns to orange. Volume Adjustment/Audio Channel Selection Volume Adjustment 1 When no menu screen is not displayed, press (volume adjustment button). For SDI input the “Volume/Embedded Audio” screen appears. For any input other than SDI the “Volume” screen appears. 2 Press to move the cursor to “Volume”. (This step is skipped when the ”Volume/Embedded Audio” screen is not displayed.) 3 Press to adjust the volume. 4 Press the MENU button to finish. (The “Volume” screen disappears automatically if no operations are made for 5 seconds.) Audio Channel Selection Select the audio channel output from the Speaker (L/R) and AUDIO (MONITOR OUT) (OUT1(L)/OUT2(R)) terminals when an EMBEDDED AUDIO signal is input during SDI input. ● It is necessary to set the audio channel group in advance. (☞ ”Embedded Audio Group” of “Audio Setting” on page 16) ● Store the setting for each input of SDI 1 and SDI 2. 1 When the menu is not displayed, use the buttons The “Volume/Embedded Audio” screen appears. ● The “Volume/Embedded Audio” screen disappears automatically is no operations are made for about 30 seconds. 2 Use the buttons to select the left and right channels (L ch/R ch) 3 Use the buttons to select the audio channel ● Each time you press a button the audio channel changes according to the “Embedded Audio Group” setting. (☞ on page 16) 4 Press the MENU button ● The “Volume/Embedded Audio” screen disappears. On the Information Display The monitor displays the information below. ● Make the setting to display/hide each information using the MENU with the exception of 5, controlled with T.C. button (☞ e on page 10). 1 Audio level meter ● You can check the conditions of the EMBEDDED AUDIO signals when “Level Meter Display” is set to “Horizontal” or “Vertical.” ● Not displayed when “Level Meter Display” is set to “Off.” (☞ “Audio Setting” on page 16) 2 Signal format ● Displayed when “Status Display” is set to “On.” (☞ “Information” on page 19) ● For the contents displayed, see “Available signals” on page 29 and “On the signal format” on page 12. 3 Source name assigned in “Character Setting” ● Displayed when “Source ID” is set to “On” or “Auto.” ● Displayed in large letters when “Status Display” is set to “Off” or “Auto.” (☞ “Information” on page 19) 4 CRC error indication ● Displayed when “CRC Error” is set to “On.” (☞ “Information” on page 19) ● A red square is displayed when an error occurs. 5 Time code ● When the input signal includes no time code, “TC – –:– –:– –:– –” is displayed (☞ e on page 10). 9ROXPH Volume screen 9ROXPH(PEHGGHG$XGLR * (PEHGGHG$XGLR/FK (PEHGGHG$XGLR5FK 9ROXPH Volume/Embedded Audio screen
12 The operation procedure 1 Press the MENU button to display the Main Menu To display the Main Menu ➡ Press the MENU button. To display the Set-Up Menu ➡ Press the button while holding the button. 0DLQ0HQX 3LFWXUH)XQFWLRQ 6L]H3RVLWLRQ$GMXVW $VSHFW 6LJQDO6HWWLQJ 0DUNHU $XGLR6HWWLQJ 6\QF)XQFWLRQ 1R2SHUDWLRQ$FWLRQ 2II 6HW8S0HQX )XQFWLRQ6HWWLQJ $OO/RFN (QJOLVK 3LFWXUH6XE$GMXVW :KLWH%DODQFH6HWWLQJ 5HPRWH6HWWLQJ ,QIRUPDWLRQ &RQWURO/RFN /DQJXDJH ,0' DOOUHVHW 2 Use the buttons to select an item and press the button to proceed to the next screen BV^cBZcj E^XijgZ;jcXi^dc H^oZ$Edh^i^dc6Y_jhi 6heZXi H^\cVaHZii^c\ BVg`Zg 6jY^dHZii^c\ HncX;jcXi^dc CdDeZgVi^dc6Xi^dc /D[[ E^XijgZ;jcXi^dc /"'% /D[[ /%, /CdgbVa /=VgY /'#' /.(%%@ 7VX`a^\]i 6eZgijgZ 6eZgijgZAZkZa 8I> AI> <VbbV 8dadgIZbeZgVijgZ hjWbZcj gZhZi 3 Use the buttons to select an item and press the button to proceed to the next screen ● For some items, pressing the buttons adjusts the setting. 4 Use the buttons to select an item and use the buttons to adjust the setting 5 Press the MENU button to finish operations ● Press the MENU button repeatedly until the menu screen disappears. On the Status Display If you press the INPUT SELECT button (☞ r on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about 3 seconds. ● Make the setting to display/hide the status in “Status Display” of the “Information” (☞ page 19). ● When “Status Display” is set to “Auto” or “On,” the status below is also displayed in the following cases: – When you change the input – When the signal condition of the current input changes – When you turn on the monitor ● When “Status Display” is set to “On,” the signal format will remain displayed 3 seconds after the status is displayed. 1 Signal format ● For the contents displayed, see “Available signals” on page 29 and “On the signal format” below. On the signal format The following messages appear depending on the type of input signals and their conditions. When a HDMI signal protected with HDCP is input When no video signal comes in When a noncompliant video signal comes in “*” (at the end of the indication) ➔ “No Sync” ➔ “Out of range” ➔ 2 Signal format of HDMI and COMPO./RGB input 3 Setting of “MUTING” • Only appears when in mute mode. (☞ 4 on page 10). Daily Operations (cont.) Main Menu Selected item Operation guide Set-Up Menu Ex.: When “Picture Function” in the Main Menu is selected Menu Configuration ● The menu screen disappears automatically if no operations are made for about 30 seconds. ● Inoperable menus will be grayed out. ● Some items will not be displayed on the menu depending on the selected input and signal format.
13 Menu Transition Diagram Main Menu Picture Function Audio Setting Sync Function No Operation Action Signal Setting Marker Aspect Backlight Aperture Aperture Level CTI LTI Gamma Color Temperature sub menu reset Level Meter Display Horizontal Channel Arrange Vertical Position Horizontal Position Meter Type Color Reference Level Over Level Bar Brightness Transparent Peak Hold Auto Adjust H Size H Position V Size V Postion Dot Cock Clock Phase sub menu reset Component/RGB Select Sampling Mode Wide XGA SXGA/SXGA+ I/P Mode Color System sub menu reset Area Marker Marker Aspect Safety Marker Safety Area Frame Center Marker Line Brightness R-Area Marker R-Marker Aspect R-Safety Marker R-Safety Area Auto Aspect Manual Aspect SD4 3 Size Balance Audio1 Assign Audio2 Assign Embedded Audio Group Level Meter Setting No Sync Action Delay Time Low Latency Size/Position Adjust Set-Up Menu Contrast Bright Chroma Phase NTSC Setup Component Level sub menu reset Color Temperature* R Drive G Drive B Drive R Cut Off G Cut Off B Cut Off sub menu reset Function Setting Picture Sub Adjust White Balance Setting Remote Setting Information Control Lock Language IMD all reset sub menu Position Sync Term Tally Setting Dimmer Illumination Component Phase Remote Active On Standby LCD Saver Setting Execute Cancel Status Start After Tally Type Tally Color 1st Start Work Time Contrast Backlight OSD Contrast Side Mask reset Serial Type Parallel Type Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 Source ID Character Setting Status Display Time Code CRC Error Sub Hour Meter Model Version Hour Meter IMD Display IMD Protocol Address IMD Size Text Color Tally 1 Color Tally 2 Color Background Color reset * : "Color Temperature" is only displayed, and cannot be set/changed.
14 Menu Configuration (cont.) Main Menu Picture Function Setting for the picture quality. Item To do Setting value Backlight Adjusts the brightness of the display. –20 to +20 Aperture*1 Activates/deactivates the function at the level set in “Aperture Level”. Off, On Aperture Level*1 Compensate the frequency response of the luminance signal of the video signal. 01 – 10 CTI Adjust the clearness of the outlines of the chrominance signal. Off, Normal, Hard LTI Adjust the clearness of the outlines of the luminance signal. Off, Normal, Hard Gamma Select the Gamma correction value. 2.2 (equivalent to Υ 2.2), 2.35 (equivalent to Υ 2.35), 2.45 (equivalent to Υ 2.45), 2.6 (equivalent to Υ 2.6) Color Temperature Select the color temperature. 9300K, 6500K, User sub menu Display the sub menu which enables you to adjust the items in “Picture Function” while viewing the actual picture. reset Restore the default settings for all the items in “Picture Function”. *1 Memorized for each input. Size/Position Adjust Adjusts the size and position of the picture. Item To do Setting value Auto Adjust Activate/deactivate the function to adjust the optimized position for each input signal. Setting value varies depending on the signals. H Size*1 Adjust the horizontal picture size. H Position*1 Adjust the horizontal picture position. V Size*1 Adjust the vertical picture size. V Position*1 Adjust the vertical picture position. Dot Clock*1 Adjust “Dot Clock” and “Clock Phase” alternately when the displayed picture becomes unstable or streaked. Clock Phase*1 –32 to +32 sub menu Display the sub menu which enables you to adjust the items in “Size/Position Adjust” while viewing the actual picture. reset Restore the default settings for all the items in “Size/Position Adjust”. *1 Memorized for each signal format. Aspect Sets the aspect ratio of the screen for displaying videos. Item To do Setting value Auto Aspect Select whether to adjust the aspect ratio (horizontal to vertical ratio of the screen) of the SD signal automatically or manually (Manual Aspect). Off, On Manual Aspect*1 Sets the aspect ratio (horizontal to vertical ratio of the screen) of the SD signal. 16:9, 4:3 SD4:3 Size*1 Selects the picture size when the input signal format is 4:3. Normal, H Full Normal : Matches the vertical picture size to the number of pixels. H Full : Matches the horizontal picture size to the horizontal size of the screen. At this time, the top and bottom of the picture are overscanned. *1 Not activate when picture is displayed in the 1:1 mode.
15 Signal Setting Settings for input signals. Item To do Setting value Component/RGB Select Selects the signal type you want to use for COMPO./RGB terminals. Component, RGB Sampling Mode Analog RGB input Standard: When the input signal is VGA60 or XGA60 Wide: When the input signal is WVGA60 or WXGA60 When the input signal is other than the above, the setting value does not affect the displayed image. Standard, Wide Wide XGA Select the analog WIDE XGA signal format. 1280*768, 1360*768 SXGA/SXGA+ Select the format when the analog SXGA60 signal comes in. SXGA: Select this when the SXGA60 signal comes in. SXGA+A: Select this when the SXGA+60/SXGA+60* signal comes in. When the input signal is other than the above, the setting value does not affect the displayed image. SXGA, SXGA+A I/P Mode*1 Selects a proper mode corresponding to the input picture. Normal, Cinema, Field Color System Select the color system. Auto, NTSC, PAL, SECAM, NTSC 4.43, PAL M, PAL N, PAL60 • If the picture is unstable with “AUTO,” select the color system according to the input signal. sub menu Display the sub menu which enables you to adjust the items in “Signal Setting” while viewing the actual picture. reset Restore the default settings for all the items in “Signal Setting”. *1 When “Low Latency” on the menu is set to “On”, forcefully perform I/P conversion using “Field” processing. Marker*1 Settings for marker functions. Item To do Setting value 1/2 Area Marker Activate/deactivate the area marker and select the style of it. The setting values and features are as follows. Off, Line, Half, Half+Line Off Line Half Half+Line : : : : Deactivate the marker. Displays the area with an outline. The area outside the specified aspect ratio of the screen is displayed at 50% transparency. The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside of that is displayed at 50% transparency. Marker Aspect Select the aspect ratio of the area marker. 4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1 Safety Marker Activate/deactivate the safety marker and select the style of it.*2 Off, Line, Half, Half+Line Safety Area Adjust the area of the safety marker. 80% – 100% Frame*3 Displays/Hides the video area. Off, On Center Marker*3 Displays/hides the marker indicating the center position of the picture. Off, On Line Brightness Adjust the brightness of the marker. High, Low 2/2 R-Area Marker Activate/deactivate the area marker and select the style of it.*2 Off, Line, Half, Half+Line R-Marker Aspect Select the aspect ratio of the area marker. 4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1 R-Safety Marker Activate/deactivate the safety marker and select the style of it.*2 Off, Line, Half, Half+Line R-Safety Area Adjust the area of the safety marker. 80% – 100% ● The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or external control. ● Select either non-“R-” items or “R-” items to activate by using external control. (☞ “External Control” on page 22) ● When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed. ● To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, set Area Marker to "Off". *1 Memorized for each signal format. *2 The setting values are the same as that of “Area Marker”. *3 In 1:1 mode, this display is grayed out and cannot be operated.
16 Menu Configuration (cont.) Audio Setting Settings for the audio output balance, EMBEDDED AUDIO signals and audio level meter signal. Item To do Setting value Balance Adjust the balance between the right and left speakers. L5 – L1, 0, R1 – R5 Audio1 Assign Select the video input through which audio is output. Analog audio is input through the AUDIO ASSIGN (IN 1) terminal. SDI-1, SDI-2, HDMI-Digital, HDMI-Analog, Component/ RGB, Video Audio2 Assign Select the video input through which audio is output. Analog audio is input through the AUDIO ASSIGN (IN 2) terminal. SDI-1, SDI-2, HDMI-Digital, HDMI-Analog, Component/ RGB, Video Embedded Audio Group*1 Select the audio channel group of the EMBEDDED AUDIO signals. The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows. (G means GROUP) 1G, 2G, 3G, 4G, 1-2G, 1-3G, 1-4G 1G 2G 1-2G 3G 1-3G 4G 1-4G : : : : : : : channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G) channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G) channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/ 1 – 8 (1G+2G) channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G) channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/ 3+4/5+6/7+8/9+10/11+12/1–4(1G)/5–8(2G)/ 9–12(3G)/1–8(1G+2G)/1–12(-3G) channel(s) 13/14/15/16/13+14/15+16/13–16(4G) channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/1+2/3+4/ 5+6/7+8/9+10/11+12/13+14/15+16/1–4(1G)/5–8(2G)/9–12(3G)/13-16(4G)/ 1–8(1G+2G)/1–12(1-3G)/1-16(1-4G) Level Meter Setting*1 Specify the audio level meter display for EMBEDDED AUDIO signal. Example of audio level meter display - Connection between the level meter position and channel Ex: When “Horizontal” is selected for “Level Meter Display”: Ex: When “Vertical” is selected for “Level Meter Display”: -10dB -20dB -20dB -10dB -20dB -10dB • The number of audio channels displayed on the level meter varies depending on the setting value of “Embedded Audio Group”. • The level meter with no audio signal input is displayed in white for “3COLORS”, and in gray for “White”. • Display position When “Horizontal” is selected for “Level Meter Display”, the display position will be the top or bottom of the screen. When “Vertical” is selected for “Level Meter Display”, the display position will be the lower right, lower left, upper left, or upper right of the screen. • When “On” is selected for “Peak Hold”, the maximum value is retained a certain period when the signal level becomes maximum. Level Meter Display Select the status of the level meter (display vertically, horizontally, or not displayed). Off, Vertical, Horizontal Horizontal Channel Arrange Select how the audio channels are displayed on the level meter. Line, Divide Vertical Position Adjust the vertical level meter position. 1, 2, 3, 4 Horizontal Position Adjust the horizontal level meter position. Upper, Lower Meter Type Specify the design of the level meter. Bar, Block Color Select the color of the level meter display. 3Colors (colored depending on the level), White (white only) Reference Level Select the standard input level indicated on the level meter. –20dB, –18dB Over Level Select the input level’s lower limit indicated in red for the “3Colors” display. –10dB, –8dB, –6dB, –4dB, –2dB Bar Brightness Select the brightness of the level meter. Low, High Transparent Adjust the transparency of the level meter display against the image. Off, Background, All Peak Hold Activates/deactivates the peak hold function of the level meter. Off, On *1 Memorized for each input. Green REFERENCE LEVEL OVER LEVEL Red Yellow OVER LEVEL REFERENCE LEVEL
17 Sync Function Settings for the synchronization with signals. Item To do Setting value No Sync Action Select the screen status when no signal is coming in. Off, Standby, Power Save (power save mode), Gray Back (gray screen) Delay Time Select the period until the screen status changes as selected in “No Sync Action” after signals stop coming in. 30s, 5min, 15min Low Latency Activates/deactivates the function to shorten the time taken to display the picture (low latency function). Off, On • If the picture is not displayed steadily while “On” is selected, select “Off.” • While “On” is selected, the displayed picture may become unstable when an operation using buttons on the front panel or the menu is performed, or when the signal format changes. ● When setting “No Sync Action” to “Gray Back,” the screen color changes to gray and the power consumption of the backlight is saved by half. Selecting “Power Save” (power save mode) saves more power consumption by turning off the backlight. No Operation Action Setting values: Off, On Setting of the function for turning the unit off (standby) automatically when no operations are made for more than 4 hours. Off: Does not turn off automatically On: Turns off automatically ● When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically. When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30 seconds. Set-Up Menu Function Setting Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps. Item To do Setting value sub menu Position Select the contents and displaying position of “sub menu.” The setting values and features are as follows. Lower1, Upper1, Lower2, Upper2 Lower1 : Displays the current setting and adjustment bar at the lower part of the screen. Upper1 : Displays the current setting and adjustment bar at the upper part of the screen. Lower2 : Displays the current setting at the lower part of the screen. Upper2 : Displays the current setting at the upper part of the screen. • The adjustment bar is not displayed for some items. Sync Term Specify the terminal resistant value of the RGB input synchronized signal from the COMPO./RGB terminal. • Normally, select “High”. Select “Low” when the display becomes unstable due to the length of a connection cable. Low, High Tally Setting Set the color and mode of the tally lamp using external control. Tally Type Normal Half : : Light up the entire tally. Light up the left and right halves of the tally individually. Normal, Half Tally Color Set the tally color when “Tally Type” is set to “Normal”. Green, Red Dimmer Select the intensity of the button lamps. Normal, Dark Illumination Select whether illumination is activated/deactivated. Off, On Component Phase Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub Adjust” in Set-Up Menu) except when an NTSC signal comes in (☞ on page 18). Enable, Disable Remote Active On Standby Set the conditions for the power switch by external control (serial). Off, On On Off : : Can power on by external control after powered OFF. Cannot power on by external control after powered OFF. LCD Saver Configure the setting for reducing damage to the LCD panel for long-time use. (☞ on page 20) Setting 1st Start Set the standby time. 00h-24h Work Time Set the time for performing the function. 01h-06h Contrast Set the contrast reduction. Save, Normal Backlight Reduce the backlight brightness. Save, Normal OSD Contrast Set the contrast reduction of the OSD display. Save, Normal Side Mask Select whether to use the side panel. * The Side Mask function works no matter whether the LCD Saver is active or stopped. Off, On reset Restore the default settings for all the items in “LCD Saver”. Execute Execute the LCD Saver function. Cancel Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.) Status Display the LCD Saver status. Off, Ready Start After Stop the LCD Saver function. **h **min
18 Menu Configuration (cont.) Picture Sub Adjust Configure the standard level of image adjustment. Item To do Setting value Contrast*1 Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front panel. –20 to +20 Bright*1 Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front panel. –20 to +20 Chroma*1 Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel. –20 to +20 Phase*1,*2 Adjust the standard level for the phase adjusted with the PHASE knob on the front panel. –20 to +20 NTSC Setup Select the set-up level of the input NTSC signal. 00 (compliant with 0 % set-up signal), 7.5 (compliant with 7.5 % set-up signal) Component Level Select the level of the analog component signal (480i and 576i only). B75 (compliant with BetacamVTR 7.5 % set-up signal), B00 (compliant with BetacamVTR 0 % set-up signal), SMPTE (compliant with M2VTR signals) sub menu Display the sub menu which enables you to adjust the items in “Picture Sub Adjust” while viewing the actual picture. reset Restore the default settings for all the items in “Picture Sub Adjust”. *1 Memorized for each input. *2 When “Component Phase” is set to “Disable,” “Phase” cannot be adjusted if no NTSC signal is input. White Balance Setting Display the color temperature, and adjusts the drive level and cutoff point of each color (R/G/B). Item To do Setting value Color Temperature Select the color temperature. (Cannot be set/changed) 9300K, 6500K, User R Drive *1 G Drive B Drive Adjust the drive level of each color (red, green, and blue). ● The maximum (Max) and minimum (Min) values vary depending on the input signal or other settings. Min – 000 – Max (in 1024 grades) R Cut Off *1 G Cut Off B Cut Off Adjust the cutoff point of each color (red, green, and blue). ● The maximum (Max) and minimum (Min) values vary depending on the input signal or other settings. Min – 000 – Max (in 1024 grades) sub menu Display the sub menu which enables you to adjust the items in “White Balance Setting” while viewing the actual picture. reset Restore the default settings for all the items in “White Balance Setting”. *1 Memorized for each color temperature. Remote Setting Settings for the external control. Item To do Setting value Serial Type Select a terminal for external control in serial mode. RS232C, RS485 Parallel Type Select a control method of the MAKE/TRIGGER terminal. Make, Trigger, Set Pin1 Assign the control functions to the pins of the MAKE/TRIGGER terminal. • Assign a function to each pin terminal by selecting “Set” in “Parallel Type” mentioned above. ☞ "Display" in "Functions controlled by the Make/ Trigger system" on page 23 Pin2 Pin3 Pin4 Pin5 Pin6 The functions are assigned for “Pin6” – “Pin8” and you cannot change the assignment of these functions. Tally Pin7 Enable Pin8 GND
19 Information Settings for the information display of the monitor. Item To do Setting value Source ID Select whether the name assigned in “Character Setting” is displayed on the screen (☞ “On the Information Display” on page 11). • When “Auto” is selected, the display color synchronizes with the color of the tally lamp while the tally lamp is lit. Off, On, Auto Character Setting Assign a name to each video source as you like (10 characters at maximum). You can also enter a name using the RS-232C system. (☞ Page 20) Status Display Display/Hide the status of the current input and the setting of MUTING. (☞ "On the Status Display" on page 12) Auto, Off, On Time Code Select the type of the TIME CODE display. VITC*1, LTC*1, D-VITC CRC Error Display/Hide the CRC error when the HD SDI signal is input. (☞ "On the Information Display" on page 11) Off, On Sub Hour Meter Display the hours of use (unit: hour). The usage time can be reset to 0. Model Display the model name of the monitor. Version Display the version of the monitor. Hour Meter*2 Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You cannot reset this item. *1 Ancillary time code *2 ”Hour Meter” and settings specified using the front knob are not reset. Control Lock*3 Setting values: Off, Volume Lock, All Lock Settings for disabling the buttons on the front panel. *3 • The following operations are not available when “Volume Lock” is selected. - Picture adjustment knob • The “All Lock” function disables to control the buttons on the front panel. But following operations are available. - Turning on/off (on standby) the monitor - Displaying the Set-Up Menu by pressing button while holding button and turning “Control Lock” to “Off” - Operating the monitor by an external control If you try other operations, “Control lock on!” appears on the screen. Language Setting values: English, Deutsch, Français, Español, Italiano, Pуccкий Select the displayed language for the menu, etc. IMD Settings for IMD (In-monitor Display). (☞ Page 20) Item To do Setting value IMD Display Display setting On: Displayed, Off: Not displayed On, Off IMD Protocol Serial communication protocol setting Off: Supports JVC protocol, TSL V4.0: Supports TSL UMD Protocol V4.0 Off, TSL V4.0 Address Address setting 000 to 126: Set a particular address 000 to 126 IMD Size Text size setting Small: Small size, Middle: Standard size, Large: Large size Small, Middle, Large Text Color Text color setting Command: Same color as that set for communication (Command) Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings Command, Red, Green, Amber, Blue, Cyan, Magenta, White Tally 1 Color Tally 1 color setting Command: Same color as that set for communication (Command) Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings Command, Red, Green, Amber, Blue, Cyan, Magenta, White Tally 2 Color Tally 2 color setting Command: Same color as that set for communication (Command) Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings Command, Red, Green, Amber, Blue, Cyan, Magenta, White Background Color Display background color setting Black: Set the background of the IMD display to black Translucent: The picture on the monitor shows through the IMD display. Transparent: Set the background of the IMD display transparent. Black, Translucent, Transparent reset Return the “IMD” settings to their default values all reset Restores all the settings and adjustments of the monitor to the default.
20 ● Setting of “Character Setting” 1 Change the input to one that you want to assign a video source name for. 2 Select “Character Setting”. 3 Press buttons to select the first character. ● Each time you press button, the character changes as follows. Press button to reverse the order. Space 4 Press button to move the arrow to the next space. ● The characters entered before moving the arrow are memorized. 5 Repeat steps 3 and 4 (10 characters at maximum). 6 Press MENU button to store the name. ● How to use the LCD Saver 1. Set reduced function to perform. 2. Set both time for starting the function and time for letting it work. 3. Activate the STANDBY MODE by Execute. ■ Aborting the ongoing function operation Operating this apparatus may lead to aborting the OPERATION MODE. ■ Stopping the operation Executing “Cancel”. Turn off the power. ● Once operating the function, unless turned off the power or executed “Cancel”, reduced function is automatically performed every 24 hours. ■ Example of setting up “1st Start” and “Work Time” ● IMD (In-monitor Display) This unit supports “TSL UMD Protocol – V4.0” from Television Systems Ltd. 16 character text display and one tally on each side can be controlled. The color of both the text and the tally can be set. Using the address setting, up to 127 units can be controlled individually. To use, set the external control terminals of this unit to serial format. For details of control commands, refer to the homepage of Television Systems Ltd. ● Low Power Mode Puts the unit into Low Power Mode 30 seconds after the monitor is switched off (standby) to further reduce power consumption. • Low Power Mode will not activate when “Remote Active On Standby” on the Set-up Menu is set to “On”. • The power lamp will be turned off during Low Power Mode. LCD Saver in standby Time to set in the 1st Start Timing to run "Execute" LCD Saver in standby LCD Saver in operation Time to set in Work Time CAM-01 Text display area * Example of lower screen IMD display Tally 2 Tally 1 Menu Configuration (cont.)
21 Function Key Setting Specify the function assigned to the F1/F2 button. ● To display “Function Key Setting” Menu Press the button when the menu is not displayed. Press the MENU button to exit from "Function Key Setting” Menu. Item To do Setting value Function1 Specify the function assigned to the F1 button. - - -, Aperture, I/P Mode, Frame, Center Marker, Level Meter Display, Gamma, Color Temperature, CRC Error Function2 Specify the function assigned to the F2 button. Function Display Select whether to display the status of the assigned function when you press the F1/F2 button. Off, Mode-1, Mode-2 Off Mode-1 Mode-2 : : : No status display. Perform the registration function. Display the status. Perform the registration function. Display the status. Do not perform the registration function. Perform the registration function when the status is displayed and the button is pressed again. * See pages 13 to 20 for details of the functions assigned to Function 1 and Function 2. ● About the operations of F1/F2 button Each time you press the button, the setting value for the assigned function changes in order. Ex: When “Color Temperature” is assigned Each time you press the button, three setting values alternate.
22 About the external control This monitor has three external control terminals. ● Make/Trigger terminal (RJ-45): The following external control systems are available. (1) Make (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. (2) Trigger (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal. ☞ “Using the Make/Trigger system” below ● RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system (☞ “Using the serial communication” on page 23). ● RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system (☞ “Using the serial communication” on page 23). Set the following items of “Remote Setting” in Set-Up Menu according to the external control terminal and control system (☞ “Serial Type,” “Parallel Type” on page 18). Control terminal Control system The settings of this unit “Serial Type” setting “Parallel Type” setting Make/ Trigger terminal Parallel Type Make — Make Trigger — Trigger RS-485 terminal Serial communication RS-485 RS485*1 — RS-232C terminal RS-232C RS232C*1 — *1 For a monitor connected to a personal computer etc, select the terminal the equipment is actually connected to. For other monitors, select “RS485.” Control priority is as follows. Make > Trigger = serial communication = buttons and menu on the monitor ● You can use external control even when “Control Lock” is set to “Volume Lock” or “All Lock” (☞ page 19). ● When the monitor is off (on standby), external control is not available. But certain external controls (starting/terminating communication, turning on the monitor) are available through the serial communication (☞ page 24). <Make/Trigger system> You can control the monitor by a personal computer or dedicated controller*2. ● “Using the Make/Trigger system” below. *2 The controller is not commercially available. Consult your dealer if you need it. <Serial communication> RS-485 IN or RS-232C RS-485 OUT RS-485 IN RS-485 OUT RS-485 IN RS-485 OUT ● For the details, see page 23. PC, etc. External Control Using the Make/Trigger system The Make/Trigger terminal is configured as follows. You can assign a function to each pin terminal in “Remote Setting” (☞ “Pin1, Pin2, Pin3, Pin4, Pin5” in “Parallel Type” on page 18). ● You cannot change the functions assigned to the pin terminals from 6th to 8th. Pin No. Pin name 1 Pin1 2 Pin2 3 Pin3 4 Pin4 5 Pin5 This is a female terminal. 6 Tally*1 7 Enable*2 8 GND *1 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is invalid). *2 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the Make system. To assign the functions to the pin terminals For the operation procedure, see page 12. 1 Select “Remote Setting” on the Set-Up Menu. 2 Set “Parallel Type” to “Set.” 3 Select a pin name (“Pin1” – “Pin5”) for which you want to assign a function, then select the function you want to assign. For the selectable functions, see the table on page 23. Operation of the external control 1 Set “Parallel Type” of “Remote Setting” to “Make” or “Trigger” in the Set-Up Menu. 2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled by the external control. 3 When the “Make” system is selected: Operate each function by short- circuiting the corresponding pin terminal to the 8th pin terminal (GND) or opening it. When the “Trigger” system is selected: Operate each function by pulse control, that is short-circuiting the corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it. ● When changing the input with Make system, activate the pin you want after deactivating the currently used pin. ● When selecting the “Trigger” system, you can operate only one function at a time. Operate the functions one by one.
23 <Functions controlled by the Make/Trigger system> Display Functions to be controlled Opening Short-circuiting – – – No function. — — Tally Color Tally lamp color selection.*1 Green Red Tally Type Tally lamp lighting method selection. Whole One half at a time Tally-L(R) Light the left half of the tally lamp in red.*2 On Off Tally-R(G) Light the right half of the tally lamp in green.*2 On Off SDI 1 Changes the input to “SDI 1.” Invalid Valid SDI 2 Changes the input to “SDI 2.” Invalid Valid HDMI Changes the input to “HDMI.” Invalid Valid Component/RGB Changes the input to “COMPO./RGB.” Invalid Valid Video Changes the input to “VIDEO.” Invalid Valid Area Marker The area marker indication. Off On Safety Marker The safety marker indication. Off On Center Marker The center marker indication. Off On Frame Indication of the area of the specified aspect ratio. Off On Marker Select Selects the items of “Marker”.*3 Non-“R-” items “R-” items Manual Aspect Changes the aspect ratio. 4:3 16:9 1:1 Displays in 1:1 mode. Off On Status Status display.*4 ☞ “On the Status Display” on page 12 Level Meter Audio level meter display. *5 Time Code Time code display. Off On Source ID ☞ “Source ID” in “Information” on page 19. *6 Color Off Color off. Color Monochrome Screens Check Screens check. *7 I/P Mode Change a mode according to a input picture. *8 Muting Muting on/off. Off On Dimmer Change the intensity of the button lamps. Normal Dark *1 Can be controlled when “Tally Type” (“Set-Up Menu” → “Function Setting” → “Tally Setting”) is set to “Normal”. *2 Can be controlled when “Tally Type” (“Set-Up Menu” → “Function Setting” → “Tally Setting”) is set to “Half”. *3 Selects which functions in “Marker” are activated, non-“R-” items or “R-” items (☞ “Marker” on page 15). *4 Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “On the Status Display” on page 12). While controlling with the Make system, the information is displayed only at the moment of short-circuiting. *5 While controlling with the Make system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When “Level Meter Display” is set to “Off,” the level meter is not displayed (“No Effect” appears). While controlling with the Trigger system, the pattern of the audio channel display is switched. *6 While controlling with the Make system, the available set-up options will be the setting value currently selected in “Source ID” (“On” or “Auto” [short- circuiting]) and “Off” (opening). While controlling with the Trigger system, uses the same set-up option as those in the Set-Up Menu (☞ “Source ID” in “Information” on page 19). *7 While controlling with the Make system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While controlling with the Trigger system, the screen changes in the same way as when pressing SCREENS CHECK button (☞ w on page 10). *8 Must be controlled with the Trigger system. The mode changes in the order of “Normal” → “Cinema” → “Field.” (This function cannot be controlled with the Make system.) ● You cannot assign the same function to different pin terminals. ● The Trigger system switches each function by short-circuiting the pin terminal for about 1 second and opening it. Using the serial communication You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal. * Consult your dealer for the details of the external control specification. <Communication specifications> Input terminal Cable Terminal specification Communication specifications RS-485 A straight LAN cable ☞ See below Baud Rate: 4800 bps Data Bits: 8 bits Parity: No parity Stop Bits: 1 bit Flow Control: No control Communication Code: ASCII Code RS-232C A straight cable with a D-sub 9-pin connector (male for the monitor, female for the personal computer etc.) <Specifications of the RS-485 terminal> Pin No. IN terminal signal OUT terminal signal 1 TXD + TXD + 2 TXD – TXD – 3 RXD + RXD + 4 NC NC 5 NC NC This is a female terminal. 6 RXD – RXD – 7 NC NC 8 GND GND <Specifications of the RS-232C terminal> Pin No. Signal 1 NC 2 RXD 3 TXD 4 NC 5 GND This is a female terminal. 6 NC 7 RTS 8 CTS 9 NC ● The 7th terminal and the 8th terminal are connected.
24 <Command outline> All commands consist of the following segments. Header Monitor ID Function Data Cr (0Dh) On Header “!” : Operation commands from the personal computer, etc. (☞ <Basic command list> below table). “?” : Reference commands from the personal computer, etc. “@” : Status returns from the monitor To start communication, send the connection command from the personal computer etc. To terminate the communication, send the termination command from the personal computer etc. Example of communication procedures <Basic command list> No. Commands Functions Data 1 ! *1 B C N 1 Cr Starts communication (connection) No data 2 ! *1 B C N 0 Cr Terminates communication (termination) No data 3 ! *1 B I D S E T x x*2 Cr Assigns the control ID 01 – 99 4 ! *1 B I D R E T Cr Initializes the control ID No data 5 ! *1 B I D D S P x x*2 Cr Displays/hides the ID 00: Hide, 01: Display 6 ! *1 B M E N U Cr Displays the Main Menu/Quits the menu operation No data 7 ! *1 B U P Cr Moves the cursor upward ( ) No data 8 ! *1 B D O W N Cr Moves the cursor downward ( ) No data 9 ! *1 B A D J R Cr Makes setting/adjustment ( ) No data 10 ! *1 B A D J L Cr Makes setting/adjustment ( ) No data 11 ! *1 B S E T U P Cr Displays the Set-Up Menu No data 12 ! *1 B P W 1 Cr Turns on the monitor No data 13 ! *1 B P W 0 Cr Turns off the monitor (on standby) No data 14 ! *1 B I N A Cr Selects “SDI 1” input No data 15 ! *1 B I N B Cr Selects “SDI 2” input No data 16 ! *1 B I N C Cr Selects “HDMI” input No data 17 ! *1 B I N D Cr Selects “COMPO./RGB” input No data 18 ! *1 B I N E Cr Selects “VIDEO” input No data 19 ! *1 B D I S P Cr Displays the status*3 No data 20 ! *1 B A M U T E x x*2 Cr Turns muting on/off 00: Off, 01: On 21 ! *1 B A S P x x*2 Cr Changes the aspect ratio 00: 4:3, 01: 16:9 22 ! *1 B V P L S Cr Increases the volume No data 23 ! *1 B V M N S Cr Reduces the volume No data 24 ! *1 B V O L x x*2 Cr Sets the volume 00-30 ● “Cr” is 0Dh. ● The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the monitor (No. 13) can be used while the monitor is off (on standby). *1 Enter the monitor’s ID for “ **.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for controlling all monitors at once. *2 Enter the appropriate data to “xx.” *3 Displays the information shown when the INPUT SELECT button currently lit is pressed (☞ “On the Status Display” on page 12). 1 Starting the communication: connection command (!00BCN1Cr) 3 Selecting “SDI 1” input (!00BINACr) 5 Terminating the communication: termination command (!00BCN0Cr) 6 Monitor’s status (@00BOKCr) 4 Monitor’s status (@00BOKCr) 2 Monitor’s status (@00BOKCr) PC, etc. Monitor External Control (cont.)
25 Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page No power supply. ● Press the button. ● Firmly insert the AC power plug. ● Turn on the POWER switch on the rear panel. 10 9 8 No picture with the power on. ● Select the correct input using the INPUT SELECT buttons. ● Connect the signal cable firmly. ● Turn on the power of the connected component and set the output correctly. ● Check whether the input signal format is acceptable on the monitor. 10 8 — 29, 30 No sound. ● Adjust the volume level. ● Deactivate the muting function. ● Connect the signal cable firmly. ● Turn on the power of the connected component and set the output correctly. 10 10 8 — “Out of Range” appears. ● Check whether the input signal format is acceptable on the monitor. 12, 29, 30 “No Sync” appears. ● Select the correct input using the INPUT SELECT buttons. ● Connect the signal cable firmly. ● Turn on the power of the connected component and output video signals. Or, check whether the video output of the component (video output setting of the VCR or graphic board of the computer) is set correctly. 10 8 — Wrong color, no color. ● Adjust each picture adjustment knob on the front panel or adjust the items of “Picture Sub Adjust” in the Set-Up Menu. Or, perform “reset” in “Picture Sub Adjust.” ● Check whether the setting of COLOR Off or SCREENS CHECK buttons are appropriate. ● Select the proper color system (“Color System”) in “Signal Setting”. ● Adjust the items of “White Balance Setting” in the Set-Up Menu. Or, perform “reset” in “White Balance Setting”. 10, 18 10 15 18 The picture becomes blurred. ● Adjust the picture contrast or brightness by using the adjustment knobs on the front panel. Or, adjust “Contrast” or “Bright” of “Picture Sub Adjust” in the Set-Up Menu. 10, 18 Wrong picture position, wrong picture size. The picture may sometimes not be able to fill the whole screen depending on the signal. In this case, nothing can be done to solve the problem. Please be aware of this beforehand. ● Check whether the setting of 1:1 is appropriate. ● Check “Manual Aspect” and “SD4:3 Size” settings in Aspect menu. ● Check whether the input signal format is acceptable on the monitor. ● Adjust the picture size (H Size/V Size) or position (H Position/V Position) of “Size/ Position Adjust” menu. 10 14 29, 30 14 Buttons on the monitor do not work. ● Set “Control Lock” in the Set-Up Menu to “Off.” ● You cannot use the buttons for the items controlled by the Make system. Disable the external control. 19 18, 22 The following are not malfunctions. ● When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed. Though the remaining picture will disappear after a while, there may be a case that it remains for a long period depending on the length of time the still image was displayed for. This is due to the characteristics of the LCD display and is not a malfunction. ● Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be missing or constantly lit. ● The following symptoms are problems only when pictures or sounds are not played back normally. ● A slight electric shock occurs when you touch the monitor. ● The top and/or rear panel of the monitor becomes hot. ● The monitor emits a cracking noise. ● The monitor emits a mechanical noise.
26 Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. When the screen goes blank, and one or some of the INPUT SELECT lamps (COMPO./RGB, VIDEO) on the front control panel start flashing... 1 Check which lamps are flashing. 2 Press button to turn off (on standby) the monitor. 3 Turn off the power switch on the rear panel. 4 Disconnect the AC power cord from the AC outlet. 5 Contact your dealer with the information about which lamps were flashing. ● If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT lamps may flash and no image may be displayed. When this happens, turn off power and wait at least 10 seconds before turning on the monitor again. If the INPUT SELECT lamps do not flash, you can use the monitor as normal. ● The self-check function does not work when the setup menu “Remote Active On Standby” is set to “Off” and you turn off the monitor (put the monitor in standby). The illustration of the monitor is of DT-E21L4. Troubleshooting (cont.)
27 Specifications General Model name DT-E21L4 DT-E17L4G Type Multi format LCD monitor Screen size Type 21 wide format Type 17 wide format Aspect ratio 16:9 Horizontal/vertical frequency (computer signal) H: 31.469 kHz – 75.000 kHz V: 49.990 Hz – 75.062 Hz * Some signals within this frequency range may not be displayed (“Out of range” is displayed). Compliant video signal format ☞ “Available signals” on page 29 Format HD SDI: BTA S-004C, SMPTE292M SD SDI: ITU-R BT.656: 525/625 SMPTE259M: 525 EMBEDDED AUDIO: SMPTE299M, SMPTE272M Audio output Internal speaker: 1.0 W + 1.0 W Operating conditions Operating temperature: 5°C – 35°C (41°F – 95°F) Operating humidity: 20% – 80% (non-condensing) (Slightly variable depending on ambient conditions for installation.) Power requirements AC 120 V, 50 Hz/60 Hz or DC 12 V – 17 V Rated current 0.6 A (AC 120 V) 3.5 A (DC 12 V - 17 V) 0.5 A (AC 120 V) 3.0 A (DC 12 V - 17 V) External dimensions (excluding protruding parts) Width: 515 mm (20 3/8˝) 515 mm (20 3/8˝) Width: 430 mm (17˝) 430 mm (17˝) Height: 352.1 mm (13 7/8˝) 347 mm (13 3/4˝) Height: 314.1 mm (12 3/8˝) 309 mm (12 1/4˝) Depth: 181 mm (7 1/4˝) 99.8 mm (4˝) Depth: 181 mm (7 1/4˝) 102 mm (4˝) (with the stand) (without the stand) (with the stand) (without the stand) Weight 7.7 kg (16.9 lbs) (with the stand) 6.2 kg (13.6 lbs) (without the stand) 7.1 kg (15.6 lbs) (with the stand) 5.6 kg (12.3 lbs) (without the stand) Accessories AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder) LCD panel Type 21˝ wide, active matrix TFT 17˝ wide, active matrix TFT Effective screen size Width: 477 mm (20 1/2˝) Height: 268 mm (12 7/8˝) Diagonal: 547 mm (21 9/16˝) Width: 382 mm (14 3/4˝) Height: 215 mm (8 3/8˝) Diagonal: 438 mm (17 1/4˝) Number of pixels displayed 1920 x 1080 Number of colors displayed 16.70 million Viewing angle (TYP.) 170° (Horizontally), 160° (Vertically) 160° (Horizontally), 60° (Upward), 80° (Downward) Brightness (TYP.) 250 cd/m2 300 cd/m2 Contrast ratio (TYP.) 1000:1 600:1 Input/output terminals Video VIDEO Input/output of composite signal: 1 line, BNC connector x 2, 1 V (p-p), 75 Ω * The input (IN) and output (OUT) terminals are bridge-connected (auto termination). HDMI HDMI signal input (compatible with HDCP): HDMI connector x 1 COMPO./RGB (R, G, B, HS, VS or Y, Pb/B-Y, Pr/R-Y) Analog Component signal input/Analog RGB signal input: 1 Line, mini D-SUB 15pin x1 Y: 1 V(p-p), 75 Ω(with sync) G, B/PB/B-Y, R/PR/R-Y: 0.7 V (p-p), 75 Ω HS, VS: 0.3 V (p-p) to 5 V (p-p) * For HS and VS, change the Low/High terminals manually. E. AUDIO HD/SD SDI (IN 1) Digital signal input (compatible with EMBEDDED AUDIO signals): auto detection, 2 line, BNC connector x 2 E. AUDIO HD/SD SDI (IN 2) E. AUDIO HD/SD SDI (SWITCHED OUT) Digital signal output (compatible with EMBEDDED AUDIO signals): 1 line switched out, BNC connector x 1 Audio AUDIO (IN) Analog audio signal input: 2 line, RCA connector x 2, Stereo mini Jack x1, 500 mV (rms), high impedance AUDIO (MONITOR OUT) Analog audio signal output: 1 line, RCA connector x 2, 500 mV (rms) External control REMOTE (MAKE/TRIGGER) ☞ “Using the Make/Trigger system” on page 22 REMOTE (RS-485) ☞ “Using the serial communication” on page 23 REMOTE (RS-232C)
28 To install the monitor on a shelf To install the monitor on a wall <Top view> <Side view> <Rear view> <Side view> Dimensions Unit: mm (inch) DT-E21L4 <Front view> <Side view> <Rear view> DT-E17L4G <Front view> <Side view> <Rear view> To install the monitor on a shelf To install the monitor on a wall <Top view> <Side view> <Rear view> <Side view> 270 (10 3/4) 114.3 (4 5/8) 210 (8 3/8) 160 (6 3/8) 30.3 (1 1/4) 36.7(11/2) 1 0 - φ 8 17.3 (3/4) 179 (7 1/8) 23.5 (1) 160 (6 3/8) 165 (6 1/2) 14.5 (5/8) 6-φ8 70 (2 7/8) 70 (2 7/8) 88.2 (3 1/2) VESA mounting holes (Size: M4, depth: 10 mm) 100 100 115 (4 5/8) 430 (17) 309 (12 1/4) 314.1 (12 3/8) 300 (11 7/8) 270 (10 3/4) 112.1 (4 1/2) 210 (8 3/8) 160 (6 3/8) 30.3 (1 1/4) 36.7(11/2) 1 0 - φ 8 15.1 (5/8) 179 (7 1/8) 88.2 (3 1/2) VESA mounting holes (Size: M4, depth: 10 mm) 100 100 115 (4 5/8) 515 (20 3/8) 347 (13 3/4) 352.1 (13 7/8) 300 (11 7/8) 18 (3/4) 102(41/8) 56 (2 1/4) 1.3 (1/16) 181 (7 1/4) 3 (1/8) 23.5 (1) 15 (5/8) 160 (6 3/8) 173.5 (6 7/8) 60 (2 3/8) 23 (1) 67 (2 3/4) 6-φ8 70 (2 7/8) 70 (2 7/8) 20.2 (7/8) 99.8 (4) 53 (2 1/8) 1.3 (1/16) 181 (7 1/4) 3 (1/8) Specifications (cont.) 15 (5/8) 60 (2 3/8) 67 (2 3/4)
29 Available signals The following signals are available for this monitor. Video signals No. Signal name Signal format shown in the status display (☞ page 12)*5 Input terminal VIDEO analog COMPO. analog RGB E.AUDIO *1 HD/SD SDI HDMI 1 NTSC NTSC √ — — — — 2 NTSC 4.43 N 4.43 √ — — — — 3 PAL-M PAL-M √ — — — — 4 PAL60 PAL60 √ — — — — 5 PAL PAL √ — — — — 6 PAL-N PAL-N √ — — — — 7 SECAM SECAM √ — — — — 8 B/W50 B/W50 √ — — — — 9 B/W60 B/W60 √ — — — — 10 480/60i 480/60i — √ — — √ 11 480/59.94i 480/59.94i — √ — √ √ 12 576/50i 576/50i — √ — √ √ 13 480/60p 480/60p — √ — — √ 14 480/59.94p 480/60p — √ — — √ 15 576/50p 576/50p — √ — — √ 16 640*480/60p 640*480/60p — — √ — √ 17 640*480/59.94p 640*480/60p — — √ — √ 18 720/60p 720/60p — √ — √ √ 19 720/59.94p 720/59.94p — √ — √ √ 20 720/50p 720/50p — √ — √ √ 21 720/30p 720/30p — — — √ — 22 720/29.97p 720/29.97p — — — √ — 23 720/25p 720/25p — — — √ — 24 720/24p 720/24p — — — √ — 25 720/23.98p 720/23.98p — — — √ — 26 1080/60i 1080/60i — √ — √ √ 27 1080/59.94i 1080/59.94i — √ — √ √ 28 1035/60i 1035/60i — — — √ √ 29 1035/59.94i 1035/59.94i — — — √ √ 30 1080/50i 1080/50i — √ — √ √ 31 1080/60p 1080/60p — √ √ — √ 32 1080/59.94p 1080/60p — √ √ — √ 33 1080/50p 1080/50p — √ √ — √ 34 1080/30p 1080/30p — — — √ √ 35 1080/29.97p 1080/29.97p — — — √ √ 36 1080/25p 1080/25p — — — √ √ 37 1080/24p 1080/24p — — — √ √ 38 1080/23.98p 1080/23.98p — — — √ √ 39 1080/30PsF 1080/30psf — — — √*2 — 40 1080/29.97PsF 1080/29.97psf — — — √*3 — 41 1080/25PsF 1080/25psf — — — √*4 — 42 1080/24PsF 1080/24psf — — — √ — 43 1080/23.98PsF 1080/23.98psf — — — √ — √: Acceptable —: Not acceptable *1 Compatible with EMBEDDED AUDIO signals. *2 The signal is recognized as 1080/60i, and the status is displayed as “1080/60i.” *3 The signal is recognized as 1080/59.94i, and the status is displayed as “1080/59.94i.” *4 The signal is recognized as 1080/50i, and the status is displayed as “1080/50i.” *5 For signal formats other than E.Audio HD/SD SDI input, **/59.94, **/29.97, and **/23.98 will be displayed as **/60, **/30, and **/24 respectively. ● HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. ● HDCP stands for High-bandwidth Digital Content Protection, a copy protection technology of high reliability licensed by Digital Content Protection, LLC.
30 Computer signals (preset) Analog RGB input (COMP./RGB terminals) and DVI input (HDMI terminal): No. Signal name Resolution Frequency Scan system Horizontal Vertical Horizontal (kHz) Vertical (Hz) 1 VGA60 640 480 31.5 59.9 Non-interlace 2 WVGA60 852 480 31.5 59.9 Non-interlace 3 SVGA60 800 600 37.9 60.3 Non-interlace 4 XGA60 1024 768 48.4 60.0 Non-interlace 5 WXGA (1280) 1280 768 47.8 60.0 Non-interlace 6 WXGA+60 1440 900 55.9 60.0 Non-interlace 7 SXGA60 1280 1024 64.0 60.0 Non-interlace 8 UXGA60 *1 1600 1200 75.0 60.0 Non-interlace 9 WUXGA60 *1 1920 1200 74.0 60.0 Non-interlace 10 1080/60p 1920 1080 67.5 60.0 Non-interlace 11 1080/50p 1920 1080 56.3 50.0 Non-interlace 12 US TEXT *2, *5 720 400 31.5 70.1 Non-interlace 13 WXGA(1360) 1360 768 47.7 60.0 Non-interlace 14 SXGA+/60A *3 1400 1050 64.0 60.0 Non-interlace 15 SXGA+/60B *4 1400 1050 65.2 60.0 Non-interlace 16 MAC13*5 640 480 35.0 66.7 Non-interlace 17 MAC16*5 832 624 49.7 74.5 Non-interlace 18 MAC19*5 1024 768 60.2 74.9 Non-interlace 19 MAC21*5 1152 870 68.7 75.1 Non-interlace *1 No. 8 and No. 9 signals come in, thin lines will become obscured because their signal resolution is higher than the screen resolution. *2 The signal is recognized as VGA400/70, and the status is displayed as “VGA400/70”. *3 The signal is recognized as SXGA+60, and the status is displayed as “SXGA+60”. *4 The signal is recognized as SXGA+60*, and the status is displayed as “SXGA+60*”. *5 Only supports analog RGB input. ● Non-preset signals may not be displayed normally even if the frequency is within the acceptable range. ● When a preset signal comes in, the signal format is shown on the status display. When a non-preset signal comes in, “Out Of Range” appears. Specification of the HDMI terminal Connect it to the HDMI output terminal of a video device. Pin No. Input signal Pin No. Input signal Pin No. Input signal 1 T.M.D.S Data 2+ 8 T.M.D.S Data 0 shield 15 SCL 2 T.M.D.S Data 2 shield 9 T.M.D.S Data 0– 16 SDA 3 T.M.D.S Data 2– 10 T.M.D.S Clock+ 17 DDC/CEC GND 4 T.M.D.S Data 1+ 11 T.M.D.S Clock shield 18 +5 V Power 5 T.M.D.S Data 1 shield 12 T.M.D.S Clock– 19 Hot Plug Detect 6 T.M.D.S Data 1– 13 CEC 7 T.M.D.S Data 0+ 14 Spare (not connected) Specification of the mini D-SUB15pin terminal Connect it to the mini D-SUB15pin output terminal of a video device. Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers. ● For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be slightly different from actual products. ● Design and specifications are subject to change without notice. ● All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or registered trademarks of their respective companies. Pin No. Input signal 1 Red video signal 2 Green video signal or Sync on Green signal 3 Blue video signal 4 Not connected 5 Ground Pin No. Input signal 6 Red video signal return 7 Green video signal return 8 Blue video signal return 9 Not connected 10 Ground 11 Not connected Pin No. Input signal 12 I2C data 13 Horizontal or Composite synchronization signal 14 Vertical synchronization signal 15 I2C clock Specifications (cont.)
© 2012 JVC KENWOOD Corporation 0212TMH-MW-MT MULTI FORMAT LCD MONITOR DT-E21L4/DT-E17L4G
Have a question about the JVC DT-E21L4U but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JVC DT-E21L4U. Please make sure that you describe your difficulty with the JVC DT-E21L4U as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.
There are no questions about the JVC DT-E21L4U yet.