JBL OnBeat Awake manual

Select a language NL 100%

View a manual of the JBL OnBeat Awake below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: JBL
  • Product: Clock Radio
  • Model/name: OnBeat Awake
  • Filetype: PDF
  • Available languages: , , , , , , , , , ,

Table of Contents

Page: 0
Quick Setup Guide
JBL OnBeat™
1. Plug the JBL OnBeat aWake’s power supply into the DC-In connector on the unit and
into a working AC power outlet. The JBL OnBeat aWake will automatically turn on. The
clock display screen will read “On” for 3 seconds and will then show “--:--”. When you
dock your device the OnBeat aWake’s clock display will synchronize with the device’s
clock and will display the current time.
DC-In Audio-In
DC In Aux In
2. If you are going to use your JBL OnBeat aWake with another audio source, plug one
end of a 3.5mm (1/8") stereo cable (not supplied) into the JBL OnBeat aWake’s Audio-In
connector, and plug the other end into the audio source’s audio out or headphone out
Thank you for purchasing the JBL OnBeat™
aWake iPad dock. This quick setup guide will
show you how to connect and set up your
dock. To download the free JBL AmpUp App
please go to the Apple App Store.
NOTE: Alarm functions described below are
only available through the JBL AmpUp app.
Page: 1
Docking Connector
Bass Ports
Power Button Source Button
Volume Up/Down
Display Screen
Snooze Button
Docking Groove
Bass ports: Place the OnBeat aWake so that the rear of its enclosure is at least 3" (76mm)
away from a wall or other surface to allow the bass ports to operate properly.
Docking groove and docking connector: Place your device into the OnBeat aWake’s
docking groove so that it is firmly seated on the docking connector.
Bass Ports
Docking Connector
Volume Up/Down
Power Button
Docking Groove
Source Button
Display Screen
Snooze Button
Page: 2
Volume Up/Down buttons: Press these buttons to raise and lower the OnBeat aWake’s
volume. To mute the sound, press both buttons at the same time. (The clock display will
show “00” for three seconds when the mute is on.) To restore the sound press either
Volume button.
Power button: When the OnBeat aWake is on, press the Power button to put it into the
standby mode. (The clock display will dim in the standby mode.) When the OnBeat aWake
is in standby, press the Power button to turn it on. (The clock display will illuminate at full
brightness when the unit is on.)
When the OnBeat aWake is in the standby mode it will automatically turn on when it
detects audio playing from a Bluetooth-connected device, a docked device or when it
detects wake-up alarm audio from a docked device.
When the OnBeat aWake is on, it will automatically enter the standby mode after 10
minutes of inactivity (no audio input and no user-control operation).
When the alarm is active, press the Power button to turn the alarm off.
Note: When the OnBeat aWake enters the standby mode it will also bring a docked device
into standby mode.
Source button: Each press of this button cycles the active source between a paired
Bluetooth device, a docked device and a device connected to the Audio input. An icon that
indicates the active source will appear on the display screen.
If you begin to play audio from a docked device while you’re listening to audio on a device
connected to the Audio input, the OnBeat aWake will automatically switch sources to the
docked device. If you begin streaming audio from a paired Bluetooth-enabled device while
you’re listening to any other source, the OnBeat aWake will automatically switch sources
to the Bluetooth-enabled device.
Display screen: When a device is docked in the OnBeat aWake the Display screen will
show the current time and an icon indicating the active source.
Snooze button: When you are using the JBL AmpUp App in a docked device, press the
Snooze button to stop the alarm for a predetermined amount of time. To download the
JBL AmpUp App go to the Apple App Store.
When the OnBeat aWake is in standby, you can press the Snooze button to turn it on.
To wirelessly stream audio to the OnBeat aWake from a Bluetooth-enabled device:
1.Press the OnBeat aWake’s Source button until the Bluetooth icon appears on the
2.Place the device in the pairing mode, then hold down the OnBeat aWake’s Source
button until its Bluetooth icon begins flashing. This will put OnBeat aWake in the
Bluetooth pairing mode. Use the device’s Bluetooth pairing menu to pair with OnBeat
aWake. (If the device requires a pairing code, it is 0000.)
3. When OnBeat aWake’s Bluetooth icon illuminates constantly, it is paired with the
device and you can stream audio via Bluetooth from the device to the OnBeat aWake.
To disconnect the Bluetooth device, press and hold the Source button. To pair OnBeat
aWake with a different Bluetooth-enabled device, repeat Steps 2 and 3 with the new
Page: 3
© 2012 HARMAN International Industries, Incorporated. All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated, registered in the
United States and/or other countries.
JBL OnBeat is a trademark of HARMAN International Industries, Incorporated.
The Bluetooth word mark and logo are registered trademarks and are owned by the Bluetooth SIG, Inc., and any use
of such marks by HARMAN International Industries, Incorporated, is under license.
iPhone, iPod, iPod touch and iPad are trademarks of Apple Inc., registered in the U.S. and other countries. iPod,
iPhone and iPad not included. “Made for iPod,” “Made for iPhone” and “Made for iPad” mean that an electronic
accessory has been designed to connect specifically to iPod or iPhone or iPad, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad
may affect wireless performance.
Features, specifications and appearance are subject to change without notice.
Part No. 920-0762-001 Rev. A
HARMAN International Industries, Incorporated
8500 Balboa Boulevard, Northridge, CA 91329 USA
Clock brightness: You can adjust the brightness of the clock readout to one of three
settings (Bright, Medium, Dim) by pressing the Snooze button while the OnBeat aWake is
on, but no audio is playing through it.
Clock format: Press and hold the Snooze button to cycle the clock between the 12-hour
and 24-hour format.
You can upgrade the OnBeat aWake’s firmware from within the JBL AmpUp App that is
installed on a docked device.
Visit the Apple App Store to download the JBL AmpUp App.
Hereby, [HARMAN International Industries, Incorporated], declares that this JBL ONBEAT AWAKE is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC, ErP 2009/125/EC Directive and RoHS
2011/65/EU Directive. The declaration of conformity may be consulted at the support section on our Web site, accessible
from www.jbl.com.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF exposure compliance requirements, this device must not be co-located or operating
in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications not expressly approved in writing by HARMAN International may void the user’s
authority to operate this equipment.
Page: 41
조작 및 표시
Docking Connector
Bass Ports
Power Button Source Button
Volume Up/Down
Display Screen
Snooze Button
Docking Groove
저음 포트: OnBeat aWake를 배치할 때는 OnBeat aWake의 외함 후면이 벽이나 다른
표면에서 최소 3"(76mm) 떨어지도록 하여 저음 포트가 제대로 작동할 수 있게 합니다.
독 그루브 및 독 커넥터: 장치를 OnBeat aWake의 독 그루브에 배치하여 독 커넥터에
단단하게 고정되도록 합니다.
저음 포트
독 커넥터
볼륨 위로/
아래로 버튼
전원 버튼
독 그루브
장치 선택 버튼
디스플레이 화면

Question & answers

There are no questions about the JBL OnBeat Awake yet.

Ask a question about the JBL OnBeat Awake

Have a question about the JBL OnBeat Awake but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the JBL OnBeat Awake. Please make sure that you describe your difficulty with the JBL OnBeat Awake as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.