Dell Latitude E7240 manual

View a manual of the Dell Latitude E7240 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Dell
  • Product: Laptop
  • Model/name: Latitude E7240
  • Filetype: PDF
  • Available languages: English, German, Dutch, Italian, Swedish, French, Polish, Finnish, Russian, Spanish, Portuguese

Table of Contents

Page: 0
Dell Latitude E7240
Owner's Manual
Regulatory Model: P22S
Regulatory Type: P22S001
Page: 1
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property
laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names
mentioned herein may be trademarks of their respective companies.
2014 -05
Rev. A03
Page: 2
Contents
1 Working on Your Computer....................................................................................................... 5
Before Working Inside Your Computer.....................................................................................................................5
Turning Off Your Computer....................................................................................................................................... 6
After Working Inside Your Computer........................................................................................................................7
2 Docking Your Computer............................................................................................................. 9
3 Removing and Installing Components................................................................................... 11
Recommended Tools.............................................................................................................................................. 11
System Overview....................................................................................................................................................11
Removing the SD Card............................................................................................................................................12
Installing the SD Card.............................................................................................................................................13
Removing the Battery............................................................................................................................................. 13
Installing the Battery.............................................................................................................................................. 14
Removing the Base Cover.......................................................................................................................................14
Installing the Base Cover........................................................................................................................................16
Removing the mSATA SSD Card.............................................................................................................................16
Installing the mSATA SSD Card..............................................................................................................................16
Removing the Keyboard Trim..................................................................................................................................16
Installing the Keyboard Trim...................................................................................................................................17
Removing the Keyboard..........................................................................................................................................17
Installing the Keyboard...........................................................................................................................................18
Removing the Palmrest...........................................................................................................................................18
Installing the Palmrest............................................................................................................................................19
Removing the Wi‐Fi Switch Board..........................................................................................................................20
Installing the Wi‐Fi Switch Board...........................................................................................................................20
Removing the Memory Module.............................................................................................................................. 20
Installing the Memory Module................................................................................................................................21
Removing the WLAN Card......................................................................................................................................21
Installing the WLAN Card....................................................................................................................................... 21
Removing the WWAN Card.................................................................................................................................... 22
Installing the WWAN Card..................................................................................................................................... 22
Removing the Display Bezel................................................................................................................................... 22
Installing the Display Bezel.....................................................................................................................................23
Removing the Display Panel................................................................................................................................... 23
Installing the Display Panel.................................................................................................................................... 24
Removing the Coin-Cell Battery..............................................................................................................................24
Installing the Coin-Cell Battery...............................................................................................................................25
Page: 3
Removing the Speakers..........................................................................................................................................25
Installing the Speakers...........................................................................................................................................26
Removing the Display-Hinge Cover........................................................................................................................ 26
Installing the Display-Hinge Cover......................................................................................................................... 27
Removing the Heatsink...........................................................................................................................................27
Installing the Heatsink............................................................................................................................................ 27
Removing the Display Assembly.............................................................................................................................28
Installing the Display Assembly..............................................................................................................................29
Removing the System Fan.......................................................................................................................................30
Installing the System Fan........................................................................................................................................30
Removing the System Board...................................................................................................................................31
Installing the System Board....................................................................................................................................32
Removing the Power Connector ............................................................................................................................32
Installing the Power Connector..............................................................................................................................33
4 Docking Port Information.........................................................................................................35
5 System Setup.............................................................................................................................37
Boot Sequence....................................................................................................................................................... 37
Navigation Keys......................................................................................................................................................37
System Setup Options.............................................................................................................................................38
Updating the BIOS ................................................................................................................................................. 47
System and Setup Password..................................................................................................................................48
Assigning a System Password and Setup Password...................................................................................... 48
Deleting or Changing an Existing System and/or Setup Password..................................................................49
6 Diagnostics.................................................................................................................................51
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...............................................................................51
Device Status Lights...............................................................................................................................................51
Battery Status Lights.............................................................................................................................................. 52
7 Specifications............................................................................................................................53
8 Contacting Dell.......................................................................................................................... 59
Page: 4
1
Working on Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your
personal safety. Unless otherwise noted, each procedure included in this document assumes that the following
conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or--if purchased separately--installed by performing the removal procedure in
reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you finish working
inside the computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For
additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/
regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a
card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its
pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some
cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs
before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any
connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning off Your Computer).
3. If the computer is connected to a docking device (docked), undock it.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
4. Disconnect all network cables from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets.
5
Page: 5
6. Close the display and turn the computer upside-down on a flat work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the
computer.
7. Remove the main battery.
8. Turn the computer top-side up.
9. Open the display.
10. Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before
opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted
metal surface to dissipate static electricity, which could harm internal components.
11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your
computer.
1. Shut down the operating system:
• In Windows 8:
– Using a touch-enabled device:
a. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.
b. Select the and then select Shut down
– Using a mouse:
a. Point to upper-right corner of the screen and click Settings.
b. Click the and select Shut down.
• In Windows 7:
1. Click Start .
2. Click Shut Down.
or
1. Click Start .
2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down..
2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not
automatically turn off when you shut down your operating system, press and hold the power button for about 4
seconds to turn them off.
6
Page: 6
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before
turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do
not use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as an
ExpressCard.
2. Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the
computer.
3. Replace the battery.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
7
Page: 8
2
Docking Your Computer
Follow the steps to dock your computer:
a. Place the docking spacer until the docking spacer clicks on its place in the docking station.
b. Place the computer on the docking spacer to dock your computer.
NOTE: This docking spacer can be used to dock only the Latitude E7240 / Latitude E7440 computers. You
cannot dock any other Dell computers using this docking station.
9
Page: 10
3
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your computer.
Recommended Tools
The procedures in this document may require the following tools:
• Small flat-blade screwdriver
• Phillips screwdriver
• Small plastic scribe
System Overview
Figure 1. Inside View — Back
1. system fan
2. mSATA card
3. battery bay
4. SD card
11
Page: 11
5. WLAN card
6. WWAN card
7. memory module
8. heatsink
Figure 2. Inside view — Front
1. coin-cell battery 2. SIM card board
3. speaker 4. system board
5. wi-fi switch board 6. system fan
7. display assembly
Removing the SD Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Press in on the SD card to release it from the computer.
3. Slide the SD card out of the computer.
12
Page: 12
Installing the SD Card
1. Slide the SD card into its slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
Removing the Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Slide the release latch to unlock the battery.
13
Page: 13
3. Lift the battery from the computer.
Installing the Battery
1. Slide the battery into its slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
Removing the Base Cover
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove battery.
14
Page: 14
3. Remove the screws that secure the base cover to the computer.
4. Lift the base cover to remove it from the computer.
15
Page: 15
Installing the Base Cover
1. Place the base cover to align with the screw holes correctly on the computer.
2. Tighten the screws to secure the base cover to the computer.
3. Install battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the mSATA SSD Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. SD card
c. base cover
3. Remove the screw that secures the mSATA SSD card and remove the mSATA SSD card from the computer.
Installing the mSATA SSD Card
1. Place the mSATA SSD card in its slot in the computer.
2. Tighten the screw to secure the mSATA SSD card to the computer.
3. Install:
a. base cover
b. SD card
c. battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard Trim
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove battery.
16
Page: 16
3. Using a plastic scribe, pry the keyboard trim to release it from the computer. Lift up to remove the keyboard trim
from the computer.
Installing the Keyboard Trim
1. Align the keyboard trim to its slot.
2. Press along the sides of the keyboard trim until it clicks in place.
3. Install battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
c. keyboard trim
3. Lift the battery bay and remove the screw that secures the keyboard to the computer.
4. Perform the following steps as shown in the illustration:
a. Lift the latch that secure the keyboard cable to the computer [1].
b. Disconnect the keyboard cable the computer [2].
5. Flip the computer and remove the screws that secure the keyboard to the computer.
17
Page: 17
6. Perform the following steps as shown in the illustration:
a. Slide the keyboard from the computer [1].
b. Lift the keyboard from the computer [2].
Installing the Keyboard
1. Connect the keyboard cable and tighten the screw that secures the keyboard to the computer.
2. Slide the keyboard into its compartment and ensure that it clicks into place.
3. Flip the computer, place the keyboard, and tighten the screws that secure the keyboard to the computer.
4. Install:
a. keyboard trim
b. base cover
c. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Palmrest
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
3. Remove the screws that secure the palmrest assembly and flip the computer.
18
Page: 18
4. Perform the following steps as shown in the illustration:
a. Disconnect the cable from the computer.
b. Lift the latch that secures the keyboard cable to the computer [1].
c. Disconnect the keyboard cable [2].
d. Disconnect the touch cable from the computer [3].
e. Unroute the cables from the slot [4].
5. Remove the screws that secure the palmrest assembly to the front of the computer. Pry the edges and lift the
palmrest assembly from the computer.
Installing the Palmrest
1. Align the palm rest assembly to its original position in the computer and snap it into place.
2. Tighten the screws to secure the palmrest assembly to the front of the computer.
3. Route the touch cable and connect to the system board.
4. Tighten the screws that secure the palmrest assembly to the base of the computer.
5. Install:
a. keyboard
b. keyboard trim
c. base cover
d. battery
e. SD card
6. Follow the procedures in After Working Inside Your Computer.
19
Page: 19
Removing the Wi‐Fi Switch Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
f. palmrest
3. Disconnect the wi-fi switch board cable from the system board and remove the screw that secures the wi-fi swtich
board to the computer. Remove the wi-fi switch board.
Installing the Wi‐Fi Switch Board
1. Insert the wi-fi switch board in its slot.
2. Connect the wi-fi switch board to the system board.
3. Tighten the screw that secures the wi-fi switch board to the system board.
4. Install:
a. palmrest
b. keyboard
c. keyboard trim
d. base cover
e. battery
f. SD card
5. Follow the procedures in After Working Inside Your Computer.
Removing the Memory Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
20
Page: 20
3. Pry the securing clips away from the memory module until it pops up. Remove the memory module from its
connector on the system board.
Installing the Memory Module
1. Insert the memory module into the socket.
2. Press the retention clips to secure the memory module to the system board.
3. Install:
a. base cover
b. battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the WLAN Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN card to the
computer. Remove the WLAN card from the computer.
Installing the WLAN Card
1. Insert the WLAN card into its connector at a 45–degree angle into its slot.
2. Tighten the screw to secure the WLAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WLAN card.
4. Install:
a. base cover
b. battery
21
Page: 21
5. Follow the procedures in After Working Inside Your Computer.
Removing the WWAN Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. SD card
c. base cover
3. Disconnect the antenna cables from the WWAN card.
4. Remove the screw that secures the WWAN card to the computer.
5. Disconnect the antenna cables from the WWAN card. Remove the screw that secures the WWAN card to the
computer and remove it.
Installing the WWAN Card
1. Place the WWAN card in its slot in the system board.
2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WWAN card.
4. Install:
a. base cover
b. SD card
c. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Display Bezel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
22
Page: 22
3. Pry the edges of the display bezel. Remove the display bezel from the display assembly.
Installing the Display Bezel
1. Align the display bezel in place and snap it in place.
2. Align the hinge covers on display assembly and snap it in place.
3. Install the battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Display Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. display bezel
3. Remove the screws that secure the display panel to the display assembly. Lift the display panel over.
23
Page: 23
4. Perform the following steps as shown in the illustration:
a. Peel the LVDS cable connector tape [1].
b. Disconnect the LVDS cable from the display panel [2].
c. Remove the display panel from the display assembly [3].
Installing the Display Panel
1. Connect the display cable (LVDS cable) to its connector on the display panel.
2. Place the display panel to its original position on the display assembly.
3. Tighten the screws to secure the display panel to the display assembly.
4. Install:
a. display bezel
b. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Coin-Cell Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
f. palmrest
3. Remove the screw that secures the coin-cell battery to the system board.
4. Perform the following steps as shown in the illustration:
a. Lift the latch that secures I/O cable to the computer [1].
b. Disconnect the I/O cable from the system board [2].
24
Page: 24
5. Disconnect the coin-cell battery cable from the system board. Unroute the cables from the slot and remove the
coin-cell battery from the computer.
Installing the Coin-Cell Battery
1. Place the coin-cell battery in its slot.
2. Route the cables and connect the coin-cell battery cable to the system board.
3. Connect the I/O cable to the system board.
4. Tighten the screw that secures the coin-cell battery to the system board.
5. Install:
a. palmrest
b. keyboard
c. keyboard trim
d. base cover
e. battery
f. SD card
6. Follow the procedures in After Working Inside Your Computer.
Removing the Speakers
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
f. palmrest
25
Page: 25
3. Perform the following steps as shown in the illustration:
a. Disconnect the speaker cable [1].
b. Remove the screws that secure the speakers to the computer.
c. Unroute the speaker cable from the system board [2].
d. Remove the speakers from the computer.
Installing the Speakers
1. Align the speakers to their original position and tighten the screws to secure the speakers to the computer.
2. Route the speaker cable on the computer and connect it to the system board.
3. Install:
a. palmrest
b. keyboard
c. keyboard trim
d. base cover
e. battery
f. SD card
4. Follow the procedures in After Working Inside Your Computer.
Removing the Display-Hinge Cover
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove battery.
3. Remove the screws that secure the display-hinge cover to the computer. Lift the display-hinge cover.
26
Page: 26
Installing the Display-Hinge Cover
1. Place the display-hinge cover and tighten the screws to secure the display-hinge cover to the computer.
2. Install battery.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Heatsink
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. mSATA
e. keyboard trim
f. keyboard
g. palmrest
h. display-hinge cover
i. display assembly
3. Remove the screws that secure the heatsink to the computer.
4. Perform the following steps as shown in the illustration:
a. Lift the heatsink from the computer [1].
b. Remove the heatsink from the computer [2].
Installing the Heatsink
1. Place the heatsink into its original position on the computer.
2. Tighten the screws to secure the heatsink to the computer.
27
Page: 27
3. Install:
a. display assembly
b. display-hinge cover
c. palmrest
d. keyboard
e. keyboard trim
f. mSATA
g. base cover
h. battery
i. SD card
4. Follow the procedures in After Working Inside Your Computer.
Removing the Display Assembly
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. SD card
c. base cover
d. keyboard
e. palmrest
3. Perform the following steps as shown in the illustration:
a. Disconnect the WLAN cable from the system board [1].
b. Unroute the WLAN cables from the slot [2].
c. Remove the screw that secures the heatsink to the computer.
28
Page: 28
4. Perform the following steps as shown in the illustration: Disconnect the antenna cables from the wireless solution.
a. Disconnect the LVDS cable from the system board [1].
b. Unroute the cable from the slot [2].
c. Remove the screws and pull the antenna cables from the holes on the base chassis that secure the display
assembly to the computer.
5. Remove the screws that secure the display assembly to the computer and lift the display assembly from the
computer.
Installing the Display Assembly
1. Insert the LVDS and wireless antenna cables through the holes on the base chassis and connect them.
2. Place the display assembly onto the computer.
3. Tighten the screws on both sides to secure the display assembly.
4. Tighten the screw that secures heatsink to the computer.
5. Route and connect the LVDS cables through the routing channel.
6. Connect the WLAN cable to the computer.
7. Install:
a. palmrest
b. keyboard
c. base cover
d. SD card
e. battery
8. Follow the procedures in After Working Inside Your Computer.
29
Page: 29
Removing the System Fan
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. SD card
c. base cover
d. keyboard trim
e. keyboard
f. palmrest
g. display-hinge cover
3. Remove the screws that secure the system fan to the computer and lift the system fan. Disconnect the system fan
cable and lift the fan from the computer.
Installing the System Fan
1. Connect the system-fan cable to the system board.
2. Tighten the screws that secure the system fan to the computer.
3. Align the system fan in its place on the system board.
4. Install:
a. display-hinge cover
b. palmrest
c. keyboard
d. keyboard trim
e. base cover
f. SD card
g. battery
5. Follow the procedures in After Working Inside Your Computer.
30
Page: 30
Removing the System Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. mSATA
e. keyboard trim
f. keyboard
g. palmrest
h. speaker
i. display-hinge cover
j. display assembly
k. system fan
l. heat sink
m. I/O cable
3. Perform the following steps as shown in the illustration:
a. Lift the I/O latch [1].
b. Remove the I/O cable from the system board [2].
c. Disconnect the I/O cable from system board[3].
d. Disconnect the speaker cable from the system board.
e. Remove the screws that secure the system board to the computer.
31
Page: 31
4. Perform the following steps as shown in the illustration:
a. Lift the left edge of system board partially to a 45-degree angle [1].
b. Remove the system board from the computer [2].
Installing the System Board
1. Align the system board in its place on the computer.
2. Tighten the screws to secure the system board.
3. Connect the following cables to the system board:
a. speaker
b. I/O cable
4. Install:
a. system fan
b. heat sink
c. display assembly
d. display-hinge cover
e. speaker
f. palmrest
g. keyboard
h. keyboard trim
i. mSATA
j. base cover
k. battery
l. SD card
5. Follow the procedures in After Working Inside Your Computer.
Removing the Power Connector
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard
e. palmrest
f. system fan
32
Page: 32
3. Disconnect the power-connector cable from the system board and remove the screw that secures the power
connector to the computer. Remove the power connector from the computer.
Installing the Power Connector
1. Insert the power connector in its slot.
2. Connect the power connector to the system board.
3. Tighten the screw that secures the power connector to the system board.
4. Install:
a. system fan
b. palmrest
c. keyboard
d. base cover
e. battery
f. SD card
5. Follow the procedures in After Working Inside Your Computer.
33
Page: 34
4
Docking Port Information
The docking port is used for connecting the laptop to a docking station (optional).
1. Docking Port
35
Page: 36
5
System Setup
Boot Sequence
Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a specific device
(for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
• Access System Setup by pressing <F2> key
• Bring up the one-time boot menu by pressing <F12> key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot-menu
options are:
• Removable Drive (if available)
• STXXXX Drive
NOTE: XXX denotes the SATA drive number.
• Optical Drive
• Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Navigation Keys
The following table displays the system setup navigation keys.
NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you
re-start the system.
Table 1. Navigation Keys
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.
Spacebar Expands or collapses a drop‐down list, if applicable.
<Tab> Moves to the next focus area.
NOTE: For the standard graphics browser only.
<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main screen
displays a message that prompts you to save any unsaved changes and restarts the system.
37
Page: 37
Keys Navigation
<F1> Displays the System Setup help file.
System Setup Options
NOTE: Depending on your computer and its installed devices, the items listed in this section may or may not
appear.
Table 2. General
Option Description
System Information This section lists the primary hardware
features of your computer.
• System Information: Displays BIOS
Version, Service Tag, Asset Tag,
Ownership Tag, Ownership Date,
Manufacture Date, and the Express
Service Code.
• Memory Information: Displays Memory
Installed, Memory Available, Memory
Speed, Memory Channels Mode, Memory
Technology, DIMM ASize, DIMM B Size,
• Processor Information: Displays
Processor Type, Core Count, Processor
ID, Current Clock Speed, Minimum Clock
Speed, Maximum Clock Speed, Processor
L2 Cache, Processor L3 Cache, HT
Capable, and 64-Bit Technology.
• Device Information: Displays Primary Hard
Drive, Fixed bay Device, System eSATA
Device, Dock eSATA Device, LOM MAC
Address, Video Controller, Video BIOS
Version, Video Memory, Panel Type,
Native Resolution, Audio Controller,
Modem Controller, Wi-Fi Device, WiGig
Device, Cellular Device, Bluetooth Device.
Battery Information Displays the battery status and the type of AC
adapter connected to the computer
Boot Sequence Allows you to change the order in which the
computer attempts to find an operating
system.
• Diskette Drive
• Internal HDD
• USB Storage Device
• CD/DVD/CD-RW Drive
• Onboard NIC
Advance Boot Option This option is required for Legacy boot mode.
This option is not allowed if Secure Boot is
enabled.
• Enable Legacy Option ROMs — This
option is disabled by default.
38
Page: 38
Option Description
Date/Time Allows you to set the date and time.
Table 3. System Configuration
Option Description
Integrated NIC Allows you to configure the integrated
network controller. The options are:
• Disabled
• Enabled
• Enabled w/PXE: This option is enabled by
default.
• Enable UEFI Network Stack: This allows
you to enable UEFI Networking Protocols
in pre-OS and early OS networking
environment.
Parallel Port Allows you to define and set how the parallel
port on the docking station operates. You can
set the parallel port to:
• Disabled
• AT
• PS2
• ECP (Latitude 7440)
Serial Port Identifies and defines the serial port settings.
You can set the serial port to:
• Disabled
• COM1 (Default Setting)
• COM2
• COM3
• COM4
NOTE: The operating system may
allocate resources even if the setting is
disabled.
SATA Operation Allows you to configure the internal SATA
hard-drive controller. The options are:
• Disabled
• AHCI
• RAID On (Default Setting)
NOTE: SATA is configured to support
RAID mode.
Drives Allows you to configure the SATA drives on
board. The options are:
• SATA-0
• SATA-1
39
Page: 39
Option Description
• SATA-2
• SATA-3
Default Setting: All drives are enabled.
SMART Reporting This field controls if the hard drive errors for
the integrated drives are reported during
system startup. This technology is part of the
SMART (Self Monitoring Analysis and
Reporting Technology) specification.
• Enable SMART Reporting - This option is
disabled by default.
USB Configuration Allows you to define the USB configuration.
The options are:
• Enable Boot Support
• Enable External USB Port
• Enable USB3.0 Controller
Default Setting: all the options are enabled.
USB PowerShare Allows you to configure the behavior of the
USB PowerShare feature. The option is
disabled by default.
• Enable USB PowerShare
Audio Allows you to enables or disables the
integrated audio controller.
• Enable AudioThis option is enabled by
default.
Keyboard Illumination Allows you to choose the operating mode of
the keyboard illumination feature. The options
are:
• Disabled (Default Setting)
• Level is 25%
• Level is 50%
• Level is 75%
• Level is 100%
Unobtrusive Mode Allows you to set the mode that will turn off all
light and sound emissions from the system.
The option is disabled by default.
• Enable Unobtrusive Mode
Miscellaneous Devices Allows you enable or disable the various on
board devices. The options are:
• Enable Microphone
• Enable Hard Drive Free Fall Protection
40
Page: 40
Option Description
• Enable Camera
• Enable Media Card
• Disable Media Card
Default Setting: All devices are enabled
Table 4. Video
Option Description
LCD Brightness Allows you to set the display brightness depending up on the power source (On
Battery and On AC).
Table 5. Security
Option Description
Admin Password This field lets you set, change, or delete the administrator (admin) password
(sometimes called the setup password). The admin password enables several
security features.
• Enter the old password
• Enter the new password
• Confirm the new password
Default Setting: Not set
System Password Allows you to set, change or delete the system password.
• Enter the old password
• Enter the new password
• Confirm the new password
Default Setting: Not set
Internal HDD-1 Password Allows you to set, change or delete the administrator password.
The drive does not have a password set by default.
• Enter the old password
• Enter the new password
• Confirm the new password
Default Setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
Password Configuration You can define the length of your password. Min = 4 , Max = 32
Password Bypass Allows you to enable or disable the permission to bypass the System and the
Internal HDD password, when they are set. The options are:
• Disabled (Default Setting)
• Reboot bypass
Password Change Allows you to enable the disable permission to the System and Hard Drive
passwords when the admin password is set.
41
Page: 41
Option Description
Default Setting: Allow Non-Admin Password Changes is not selected
Non-Admin Setup Changes Allows you to determine whether changes to setup option are permitted when an
administrator password is set. The option is disabled.
• Allows Wireless Switch Changes
TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST.
Default Setting: The option is disabled.
Computrace Allows you to activate or disable the optional Computrace software The options
are:
• Deactivate (Default Setting)
• Disable
• Activate
NOTE: The Activate and Disable options will permanently activate or disable
the feature and no further changes will be allowed
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Default Setting: Enable CPU XD Support
OROM Keyboard Access Allows you to set access to enter the Option ROM Configuration screens using
hotkeys during boot process. The options are:
• Enable (Default Setting)
• One Time Enable
• Disable
Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator password
is set.
Default Setting: Disabled
Table 6. Secure Boot
Secure Boot Enable Allows you to enable or disable Secure Boot feature
• Disabled
• Enabled(Default Setting)
NOTE: For enable system needs to be UEFI boot mode and enable legacy
option ROMs to be turned off.
Expert key Management Allows you to manipulate the security key databases only if the system is in
Custom Mode. The Enable Custom Mode option is disabled by default. The options
are:
• PK
• KEK
• db
• dbx
42
Page: 42
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx
appear. The options are:
• Save to File- Saves the key to a user-selected file
• Replace from File- Replaces the current key with a key from a user-selected
file
• Append from File- Adds a key to the current database from a user-selected
file
• Delete- Deletes the selected key
• Reset All Keys- Resets to default setting
• Delete All Keys- Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made will be erased
and the keys will restore to default settings.
Table 7. Performance
Option Description
Multi Core Support This field specifies whether the process will
have one or all cores enabled. The
performance of some applications will
improve with the additional cores. This option
is enabled by default. Allows you to enable or
disable multi-core support for the processor.
The options are:
• All (Default Setting)
• 1
• 2
Intel SpeedStep Allows you to enable or disable the Intel
SpeedStep feature.
Default Setting: Enable Intel SpeedStep
C States Control Allows you to enable or disable the additional
processor sleep states.
Default Setting: The option C states is
enabled.
Intel TurboBoost Allows you to enable or disable the Intel
TurboBoost mode of the processor.
Default Setting: Enable Intel TurboBoost
Hyper-Thread Control Allows you to enable or disable the
HyperThreading in the processor.
Default Setting: Enabled
Rapid Start Technology The Intel Rapid Start feature might improve
the battery life by automatically putting the
system into a low power state during sleep
after a user specified time. The options are
enabled by default:
• Intel Rapid Start Feature
• Transition to Rapid Start when using Timer
43
Page: 43
Option Description
The Rapid Start Timer value can be configure
to put the system into Rapid State as per
requirement.
Table 8. Power Management
Option Description
AC Behavior Allows the computer to power-on automatically, when AC adapter is plugged. The
option is disabled.
• Wake on AC
Auto On Time Allows you to set the time at which the computer must turn on automatically. The
options are:
• Disabled (Default Setting)
• Every Day
• Weekdays
• Select Days
USB Wake Support Allows you to enable the USB devices to wake the computer from standby mode.
The option is disabled
• Enable USB Wake Support
Wireless Radio Control Allows you to control the WLAN and WWAN radio. The options are:
• Control WLAN radio
• Control WWAN radio
Default Setting: both the options are disabled.
Wake on LAN/WLAN This option allows the computer to power up from the off state when triggered by a
special LAN signal. Wake-up from the Standby state is unaffected by this setting
and must be enabled in the operating system. This feature only works when the
computer is connected to AC power supply.
• Disabled - Does not allow the system to power on by special LAN signals when
it receives a wake-up signal from the LAN or wireless LAN. (Default Setting)
• LAN Only - Allows the system to be powered on by special LAN signals.
• WLAN Only
• LAN or WLAN
• LAN with PXE Boot
Block Sleep Allows you to block the computer from entering into the sleep state. Option is
disabled by default.
• Block Sleep (S3)
Peak Shift Peak Shift can be used to minimize AC consumption during peak powers times of
day. Set the start and end time to run in Peak Shift mode.
• Enable Peak Shift (Disabled)
44
Page: 44
Option Description
Advanced Battery Charge
Configuration
Allows batteries in the system in Advanced Battery Charge Mode to maximize
battery health. This uses standard charging algorithm and other techniques during
non-work hours to maximize battery health
• Enable Advanced Battery Charge Mode(Disabled)
Primary Battery Configuration Allows you to define how to use the battery charge, when AC is plugged in. The
options are:
• Adaptive(Enabled)
• Standard Charge
• Express Charge
• Primary AC Use
• Custom Charge — you can set the percentage to which the battery must
charge.
Intel Smart Connect Technology The option is disabled by default. If option enables will periodically sense nearby
wireless connection while the system is asleep. It will synchronize emails or social
media application that were open when system entered the sleep state.
• Smart Connection(Disabled)
Table 9. POST Behavior
Option Description
Adapter Warnings Allows you to activate the adapter warning messages when certain power
adapters are used. The option is enabled by default.
• Enable Adapter Warnings
Keypad (Embedded) Allows you to choose one of two mode it enable the keypad that us embedded in
the internal keyboard.
• Fn Key Only
• By Numlock
NOTE: When setup is running, this option has no effect, Setup works in the
“Fn Key Only” mode.
Mouse/Touchpad Allows you to define how the computer handles the mouse and touchpad input. The
options are:
• Serial Mouse
• PS2 Mouse
• Touchpad/PS-2 Mouse (Default Setting)
Numlock Enable Specifies if the NumLock function can be enabled when the computer boots. This
option is enabled by default.
• Enable Numlock
Fn Key Emulation Allows you to match the <Scroll Lock> key feature of PS-2 keyboard with the <Fn>
key feature in an internal keyboard. The option is enabled by default.
45
Page: 45
Option Description
• Enable Fn Key Emulation
Fastboot Allows you to speed up the boot process by bypassing some compatibility steps.
• Minimal
• Thorough
• Auto
Extended BIOS POST Time Allows to creates an additional pre-boot delay and allows the user to see POST
status message.
• 0 seconds
• 5 seconds
• 10 seconds
Table 10. Virtualization Support
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
Default Setting: Enable Intel Virtualization Technology
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional
hardware capabilities provided by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O — This option is enabled by default.
Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM) can
utilize the additional hardware capabilities provided by Intel Trusted Execution
Technology. The TPM virtualization Technology, and Virtualization technology for
direct I/O must be enabled to use this feature.
Trusted Execution — disabled by default.
Table 11. Wireless
Option Description
Wireless Switch Allows you to determine which wireless device can be controlled by the wireless
switch. The options are:
• WWAN
• WLAN
• Bluetooth
• WiGig
All options are enabled by default.
Wireless Device Enable Allows you to enable or disable the wireless devices. The options are:
• WWAN
• Bluetooth
• WLAN/WiGig
All options are enabled by default.
46
Page: 46
Table 12. Maintenance
Option Description
Service Tag Displays the service tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This
option is not set by default.
Table 13. System Logs
Option Description
BIOS events Displays the system event log and allows you to clear the log.
• Clear Log
Thermal Events Displays the thermal event log and allows you to clear the log.
• Clear Log
Power Events Displays the power event log and allows you to clear the log.
• Clear Log
Updating the BIOS
It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For
laptops, ensure that your computer battery is fully charged and connected to a power outlet
1. Re-start the computer.
2. Go to dell.com/support.
3. Enter the Service Tag or Express Service Code and click Submit.
NOTE: To locate the Service Tag, click Where is my Service Tag?
NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the instructions on screen.
4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.
5. Choose the Product Type from the list.
6. Select your computer model and the Product Support page of your computer appears.
7. Click Get drivers and click View All Drivers.
The Drivers and Downloads page opens.
8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.
9. Identify the latest BIOS file and click Download File.
You can also analyze which drivers need an update. To do this for your product, click Analyze System for Updates
and follow the instructions on the screen.
10. Select your preferred download method in the Please select your download method below window; click Download
File.
The File Download window appears.
11. Click Save to save the file on your computer.
12. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
47
Page: 47
System and Setup Password
You can create a system password and a setup password to secure your computer.
Password Type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the BIOS settings of your
computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
NOTE: Your computer is shipped with the system and setup password feature disabled.
Assigning a System Password and Setup Password
You can assign a new System Password and/or Setup Password or change an existing System Password and/or Setup
Password only when Password Status is Unlocked. If the Password Status is Locked, you cannot change the System
Password.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you
need not provide the system password to log on to the computer.
To enter a system setup, press <F2> immediately after a power-on or re-boot.
1. In the System BIOS or System Setup screen, select System Security and press <Enter>.
The System Security screen appears.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password , enter your system password, and press <Enter> or <Tab>.
Use the following guidelines to assign the system password:
• A password can have up to 32 characters.
• The password can contain the numbers 0 through 9.
• Only lower case letters are valid, upper case letters are not allowed.
• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
Re-enter the system password when prompted.
4. Type the system password that you entered earlier and click OK.
5. Select Setup Password, type your system password and press <Enter> or <Tab>.
A message prompts you to re-type the setup password.
6. Type the setup password that you entered earlier and click OK.
7. Press <Esc> and a message prompts you to save the changes.
8. Press <Y> to save the changes.
The computer reboots.
48
Page: 48
Deleting or Changing an Existing System and/or Setup Password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing
System and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password
Status is Locked.
To enter the System Setup, press <F2> immediately after a power-on or reboot.
1. In the System BIOS or System Setup screen, select System Security and press <Enter>.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.
4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.
NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you
delete the System and/or Setup password, confirm the deletion when promoted.
5. Press <Esc> and a message prompts you to save the changes.
6. Press <Y> to save the changes and exit from the System Setup.
The computer reboots.
49
Page: 50
6
Diagnostics
If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical
assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional
equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the
diagnostics results to help you solve the problem.
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is
embedded with the BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of
options for particular devices or device groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may
cause invalid results or error messages.
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the
computer terminal when the diagnostic tests are performed.
1. Power-on the computer.
2. As the computer boots, press the <F12> key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the computer. The
diagnostics starts running the tests on all the detected devices.
4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the diagnostic test.
5. Select the device from the left pane and click Run Tests.
6. If there are any issues, error codes are displayed.
Note the error code and contact Dell.
Device Status Lights
Table 14. Device Status Lights
Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Turns on when the computer reads or writes data.
51
Page: 51
Turns on steadily or blinks to indicate battery charge status.
Turns on when wireless networking is enabled.
The device status LEDs are usually located either on the top or left side of the keyboard. They are used to display the
storage, battery and wireless devices connectivity and activity. Apart from that they can be useful as a diagnostic tool
when there's a possible failure to the system.
The following table lists how to read the LED codes when possible errors occur.
Table 15. LED Lights
Storage LED Power LED Wireless LED Fault Description
Blinking Solid Solid A possible processor failure has occurred.
Solid Blinking Solid The memory modules are detected but has encountered an
error.
Blinking Blinking Blinking A system board failure has occurred.
Blinking Blinking Solid A possible graphics card/video failure has occurred.
Blinking Blinking Off System failed on hard drive initialization OR System failed in
Option ROM initialization.
Blinking Off Blinking The USB controller encountered a problem during
initialization.
Solid Blinking Blinking No memory modules are installed/detected.
Blinking Solid Blinking The display encountered a problem during initialization.
Off Blinking Blinking The modem is preventing the system from completing POST
Off Blinking Off Memory failed to initialize or memory is unsupported.
Battery Status Lights
If the computer is connected to an electrical outlet, the battery light operates as follows:
Alternately
blinking amber
light and white
light
An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop.
Alternately
blinking amber
light with steady
white light
Temporary battery failure with AC adapter present.
Constantly
blinking amber
light
Fatal battery failure with AC adapter present.
Light off Battery in full charge mode with AC adapter present.
White light on Battery in charge mode with AC adapter present.
52
Page: 52
7
Specifications
NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your
computer. For more information about the configuration of your computer, go to Help and Support in your
Windows operating system and select the option to view information about your computer.
Table 16. System Information
Feature Specification
Chipset Lynx Point-LP (Latitude 7240)
Intel QM87 Express Chipset (Latitude 7440)
DRAM bus width 64-bit
Flash EPROM SPI 32 Mbits, 64 Mbits
PCIe bus 100 MHz
External Bus Frequency DMI (5GT/s)
Table 17. Processor
Feature Specification
Types Intel Core i3 / i5 / i7series
L3 cache 3 MB, 4MB, 6 MB, and 8 MB
Table 18. Memory
Feature Specification
Memory connector Two SODIMM slots
Memory capacity 2GB, 4GB, or 8GB
Memory type DDR3L SDRAM (1600 MHz)
Minimum memory 2 GB
Maximum memory 16 GB
Table 19. Audio
Feature Specification
Type four-channel high-definition audio
Controller Realtek ALC3226
Stereo conversion 24-bit (analog-to-digital and digital-to-analog)
Interface:
53
Page: 53
Feature Specification
Internal high-definition audio
External microphone-in, stereo headphones, and headset combo
connector
Speakers two
Internal speaker amplifier 1 W (RMS) per channel
Volume controls hot keys
Table 20. Video
Feature Specification
Type integrated on system board
Controller:
UMA Intel HD Graphics 4600
Discrete AMD Radeon HD 8690M Graphics
Data bus PCI-E Gen3 x8
External display support
• one HDMI
NOTE: Support two DP/DVI ports through Docking station.
Table 21. Camera
Features Specification
Camera Resolution 1280 x 720 pixels
Video Resolution (maximum) 1280 x 720 pixels
Diagonal viewing angle 74 °
Table 22. Communications
Features Specification
Network adapter 10/100/1000 Mb/s Ethernet (RJ-45)
Wireless internal wireless local area network (WLAN) and wireless wide
area network (WWAN)
Table 23. Ports and Connectors
Features Specification
Audio one microphone/stereo headphone/speakers connector
Video Mini DisplayPort connector
Network adapter RJ-45 connector
USB 3.0 two USB 3.0 compliant connectors
54
Page: 54
Features Specification
Memory card reader Support upto SD4.0
Micro Subscriber Identity Module (uSIM) card one
Docking port one
Table 24. Display
Feature Specification
Latitude 7240 Latitude 7440
Type HD Anti-Glare HD Anti-Glare
Dimensions:
Height 180.0 mm (7.08 inches) 205.6 mm (8.09 inches)
Width 300.90 mm (11.84 inches) 320.9 mm (12.63 inches)
Diagonal 3.6 mm (0.14 inch) 3.6 mm (0.14 inch)
Maximum resolution 1366 x 768 1366 x 768
Refresh rate 60 Hz 60 Hz
Minimum Viewing Angles:
Horizontal +/-40° +/-40°
Vertical +15°/-30° +15°/-30°
Pixel pitch 1.05 1.05
Table 25. Keyboard
Feature Specification
Number of keys United States: 86 keys, United Kingdom: 87 keys, Brazil: 87 keys,
and Japan: 90 keys
Table 26. Touchpad
Feature Specification
Latitude 7240 Latitude 7440
Active Area:
X-axis 98.8 mm 100 mm
Y-axis 60.8 mm 47 mm
Table 27. Battery
Feature Specification
Type
• 3-cell “smart” Lithium ion
55

Question & answers

There are no questions about the Dell Latitude E7240 yet.

Ask a question about the Dell Latitude E7240

Have a question about the Dell Latitude E7240 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Dell Latitude E7240. Please make sure that you describe your difficulty with the Dell Latitude E7240 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.