Chief LPK1 manual

View a manual of the Chief LPK1 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Chief
  • Product: Projector accessory
  • Model/name: LPK1
  • Filetype: PDF
  • Available languages: English, German, French

Table of Contents

Page: 0
I N S T A L L A T I O N I N S T R U C T I O N S
INSTRUCTIONS D'INSTALLA TION
M O N T A G E A N L E I T U N G
Low Profile Projector Mounting Kit
Kit de montage peu encombrant pour projecteur
Projektorhalterungsset mit flachem Profil
LPK1
Page: 1
LPK1 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the LPK1 does not exceed 250 lbs
(113.4 kg).
• The weight capacity of the LPK1 may be LIMITED to
the lowest weight capacity of any other components
located between the VCM and the supporting structure!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The LPK1 mount is designed to be:
• mounted to double 2" x 4" wood stud cross bracing
between two 2" x 4" ceiling joists; or
• mounted to a concrete ceiling with a minimum
thickness of 8" and a maximum drywall covering of
5/8" using 5/16" x 2-1/2" lag bolts (not included) for
Fischer UX8 concrete anchors (not included) or
Toggler AF8 concrete anchors (not included); or
• suspended from four 3/8 in. diameter ASTM A307 or
stronger threaded rods (Threaded rods must have 16
threads per inch - not included) which are secured to a
1-5/8" x 1-5/8" 12ga metal framing strut channel
(spanning a maximum of 4 feet--not included) by ASTM
A307 or stronger 3/8" channel nuts (not included).
• used with a UL Listed Chief VCM projector mount.
--SAVE THESE INSTRUCTIONS--
Page: 3
LPK1 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/2"
7/32" (wood stud)
5/16" (concrete)
A (1)
[LPK1 bracket]
Page: 4
Installation Instructions LPK1
5
PREPARATION
1. Remove and SAVE four nuts from top of VCM mount (not
included). (See Figure 1)
2. Remove and discard top slide plate. (See Figure 1)
Figure 1
3. Place LPK1 mount (A) open side up on top of VCM, with
VCM studs fitting through LPK1 slots. (See Figure 2)
4. Tighten LPK1 (A) in place using four nuts removed in Step 1.
(See Figure 2)
Figure 2
INSTALLATION
The LPK1 mount is designed to be:
• mounted to double 2" x 4" wood stud cross bracing
between two 2" x 4" ceiling joists;
• mounted to a concrete ceiling with a minimum
thickness of 8" and a maximum drywall covering of
5/8" using 5/16" x 2-1/2" lag bolts (not included) for
Fischer UX8 concrete anchors (not included) or
Toggler AF8 concrete anchors (not included); or
• suspended from four 3/8 in. diameter ASTM A307 or
stronger threaded rods (not included) which are
secured to a 1-5/8" x 1-5/8" 12ga metal framing strut
channel (spanning a maximum of 4 feet--not included)
by 3/8" channel nuts (not included).
NOTE: Proceed to Wood Stud Installation section, Solid
Concrete Installation section, or Threaded Rod
Installation section.
Wood Installation
1. Carefully determine required mounting location.
IMPORTANT ! : This will require knowing the lens to
screen distance. See projector specifications for details
on determining this distance.
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
IMPORTANT ! : The LPK1 mounts are designed to be
mounted to double 2" x 4" wood stud cross bracing between
two ceiling joists.
2. Using the LPK1 as a guide, mark four mounting hole
locations. Hole locations must be centered on 2" x 4" cross
braces.
3. Drill four 7/32" diameter x 1-3/4" long pilot holes.
Figure 3
Top slide
plate
1 x 4
VCM
2
3 x 4
2
(A)
2 3
x 4
Page: 5
LPK1 Installation Instructions
6
4. Align four mounting holes in LPK1 with four pilot holes. (See
Figure 4)
IMPORTANT ! : Make sure mount is properly oriented
towards target before securing to structure.
5. Secure LPK1 to structure using four 5/16" flat washers and
four 5/16" x 2-1/2" hex head lag bolts (not included). (See
Figure 4)
Figure 4
Solid Concrete Installation
1. Determine mounting location.
WARNING: The LPK1 is designed to be mounted to a
concrete ceiling with a minimum thickness of 8" and a
maximum drywall covering of 5/8".
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
2. Using the LPK1 as a guide, mark four mounting hole
locations on ceiling. (See Figure 5)
3. Drill four 5/16" diameter x 3-1/4" long pilot holes. (See
Figure 5)
4. Align four mounting holes in LPK1 with four pilot holes.
Figure 5
IMPORTANT ! : Make sure mount is properly oriented
towards target before securing to structure.
WARNING: Anchors (not provided) must be installed into
structurally sound solid concrete. Installation into hollow
concrete block, mortar, or concrete that exhibits cracking,
spalling, or other defects may result in failure of anchor and
serious personal injury or damage to equipment.
5. Install four Fischer UX8 or Toggler AF8 concrete anchors
(not included) by inserting into pilot holes and pounding in
until flush with mounting surface. (See Figure 6)
6. Secure LPK1 with attached VCM (not included) to structure
using four 5/16" flat washers (not included) and four
5/16" x 2-1/2" lag bolts (not included). (See Figure 6)
Figure 6
x 4
5
x 4
3
x 4
2
x 4
6
5 x (4)
x 4
Page: 6
Installation Instructions LPK1
7
Threaded Rod Installation
The LPK1 may be suspended from four 3/8" diameter ASTM
A307 or stronger threaded rods (not included) which are
secured to a 1-5/8" x 1-5/8" 12ga metal framing strut channel
(spanning a maximum of 4 feet--not included) by ASTM A307 or
stronger 3/8" channel nuts (not included).
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
1. Carefully determine required mount position.
IMPORTANT ! : This will require knowing the lens to
screen distance. See projector specifications for
determining this distance.
2. Secure one end of the threaded rod to the structural
member.
3. Install four 3/8" jam nuts and washers on each threaded rod.
4. Install the LPK1 with VCM (not included) onto the threaded
rod. (See Figure 7)
5. Secure the LPK1 to the threaded rod using four 3/8"
washers and jam nuts. (See Figure 7)
Figure 7
INSTALLING PROJECTOR
Install projector with attached interface bracket to VCM (not
included) following instructions included with the VCM.
4
x 8
5
x 8
Page: 17
LPK1 Installation Instructions
18
Page: 18
Installation Instructions LPK1
19
Page: 19
LPK1 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002410 Rev00
2013 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
05/13
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477

Question & answers

There are no questions about the Chief LPK1 yet.

Ask a question about the Chief LPK1

Have a question about the Chief LPK1 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Chief LPK1. Please make sure that you describe your difficulty with the Chief LPK1 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.