Casio Waveceptor WV200A-1AV manual

View a manual of the Casio Waveceptor WV200A-1AV below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Casio
  • Product: Sport Watch
  • Model/name: Waveceptor WV200A-1AV
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 0
Operation Guide 3140
1
MA0810-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
• This watch does not have a time zone that corresponds to the UTC offset of
–3.5 hours. Because of this, the radio-controlled timekeeping and World Time
functions will not display the correct time for Newfoundland, Canada.
Caution!
Your watch is shipped with its Auto Display feature (which continually changes the
contents of the digital display) turned on. Calibration signal reception is disabled while
Auto Display is turned on.
Press any button to turn off Auto Display and return to the Timekeeping Mode.
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need in order to perform operations in
each mode. Further details and technical information
can be found in the “Reference” section.
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Timekeeping Mode World Time Mode Countdown
Timer Mode
Alarm Mode
Stopwatch Mode
Press .
Radio-controlled Atomic Timekeeping
This watch receives a time calibration signal and updates
its time setting accordingly.
• Supported time calibration signals: United States (Fort
Collins), England (Anthorn).
• See the information under “Signal Reception
Troubleshooting” if you experience problems with time
calibration signal reception.
Current Time Setting
This watch adjusts its time setting automatically in
accordance with a time calibration signal. You can also
perform a manual procedure to set the time and date,
when necessary.
• The first thing you should do after purchasing this
watch is to specify your Home City (the city where you
normally will use the watch). For more information,
see “To specify your Home City”.
• When using the watch outside the areas covered by the time signal transmitters, you
will have to adjust the current time setting manually as required. See “Timekeeping”
for more information about manual time settings.
• The U.S. time calibration signal can be picked up by the watch while in North
America. The term “North America” in this manual refers to the area that consists of
Canada, the continental United States, and Mexico.
To specify your Home City
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press D(east) and B(west) to select the city code you
want to use as your Home City.
• Time calibration signal reception is supported when
any one of the city codes shown in the table below is
selected as your Home City.
U.S. Signal U.K. Signal
City
Code
City
Name
City
Code
City
Name
City
Code
City
Name
City
Code
City
Name
HNL Honolulu YWG Winnipeg LIS Lisbon ATH Athens
ANC Anchorage CHI Chicago LON London MOW Moscow
YVR Vancouver MIA Miami MAD Madrid
LAX Los Angeles YTO Toronto PAR Paris
YEA Edmonton NYC New York ROM Rome
DEN Denver YHZ Halifax BER Berlin
MEX Mexico City YYT St. Johns STO Stockholm
3. Press A twice to exit the setting screen.
Day of week
Year
Home Time
(Hour : Minutes Seconds)
Month – Day
PM indicator DST
indicator
Important!
• Normally, your watch should show the correct time as soon as you select your Home
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night). You can also perform manual receive or you
can set the time manually.
• The watch will receive the time calibration signal automatically from the applicable
transmitter (in the middle of the night) and update its settings accordingly. For
information about the relationship between city codes and transmitters, see “Home
City Codes and Transmitters”.
• Under factory default settings, auto receive is turned off for all of the following city
codes: HNL (Honolulu), ANC (Anchorage), ATH (Athens), and MOW (Moscow). For
details about turning on auto receive for these city codes, see “To turn auto receive
on and off”.
• You can disable time signal reception, if you want. See “To turn auto receive on and
off” for more information.
• See the maps under “Approximate Reception Ranges” for information about the
reception ranges of the watch.
• If you are in an area that does not use Daylight Saving Time (summertime), turn off
the DST setting.
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to
six times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. For more information, see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
City code
Page: 1
Operation Guide 3140
2
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side facing towards a window.
This watch is designed to receive a time calibration signal late at night. Because of
this, you should place the watch near a window as shown in the illustration when
you take it off at night. Make sure there are no metal objects nearby.
12 o’clock
or
• Make sure the watch is facing the right way.
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
construction
site, airport,
or other
sources of
electrical
noise
Near
high-tension
power lines
Among or
behind
mountains
Inside or
among
buildings
• Signal reception normally is better at night than during the day.
• Time calibration signal reception takes from two to seven minutes. Take care that
you do not perform any button operations or move the watch during this time.
• The time calibration signal the watch will attempt to pick up depends on its current
Home City code setting as shown below.
Home City Codes and Transmitters
Home City Code Transmitter Frequency
HNL*, ANC*, YVR, LAX, YEA,
DEN, MEX, YWG, CHI, MIA,
YTO, NYC, YHZ, YYT
Fort Collins, Colorado
(the United States)
60.0 kHz
LIS, LON, MAD, PAR, ROM,
BER, STO, ATH*, MOW*
Anthorn (England) 60.0 kHz
* The areas covered by the HNL, ANC, ATH, and MOW city codes are quite far
from the time calibration signal transmitters, and so certain conditions may cause
problems with signal reception.
Approximate Reception Ranges
U.S. Signal
Fort Collins
600 miles
(1,000 kilometers)
2,000 miles
(3,000 kilometers)
Anthorn
500 kilometers
1,500 kilometers
U.K. signal transmitter approximate
reception range as of April 2007
U.K. Signal
• Signal reception may not be possible at the distances noted below during certain
times of the year or day. Radio interference may also cause problems with reception.
Anthorn (England) transmitter: 500 kilometers (310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
• In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which
resulted in a slight shift in the approximate reception range of the signal. The shift is
so slight that there is virtually no change in the ability to receive the signal.
• Even when the watch is within the reception range of a transmitter, signal reception
may be impossible at times due to the effects of geographic contours, structures,
weather, the season of the year, the time of day, radio interference, etc. Note that
the signal becomes weaker at distances of approximately 500 kilometers from the
transmitter, which means that the influence of the conditions listed above becomes
even greater.
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day.
When any auto receive is successful, the remaining auto receive operations are not
performed. The reception schedule (calibration times) depends on your currently
selected Home City, and whether standard time or Daylight Saving Time is selected
for your Home City.
Your Home City
Auto Receive Start Times
1 2 3 4 5 6
HNL, ANC, YVR,
LAX, YEA, DEN,
MEX, YWG, CHI,
MIA, YTO, NYC,
YHZ, YYT
Standard Time
Daylight
Saving Time
Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
LIS, LON
Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
Daylight
Saving Time
2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
MAD, PAR, ROM,
BER, STO
Standard Time 2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
Daylight
Saving Time
3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
ATH
Standard Time 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
Daylight
Saving Time
4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
MOW
Standard Time 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
Daylight
Saving Time
5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
4:00 am
*
* Next day
Note
• When a calibration time is reached, the watch will receive the calibration signal
only if it is in either the Timekeeping Mode or World Time Mode. Reception is not
performed if a calibration time is reached while you are configuring settings.
• Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• The watch receives the calibration signal for two to seven minutes everyday when
the time in the Timekeeping Mode reaches each of the calibration times. Avoid
performing any button operation within seven minutes before or after any one of the
calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the displayed
time actually is the correct time.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received.
For best reception, be sure to keep the watch in a location where signal strength is
strongest.
Weak
(Level 0)
Strong
(Level 3)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• Following reception of the time calibration signal and calibration of the watch’s time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
• The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
• The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display when the first auto receive operation of the day
is performed.
To perform manual receive
1. Place the watch on a stable surface so its top (12
o’clock side) is facing towards a window.
2. In the Timekeeping Mode, hold down D for about two
seconds until RC! appears on the display.
• Time calibration signal reception takes from two to
seven minutes. Take care that you do not perform any
button operations or move the watch during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen.
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press D.
• If the receive operation is unsuccessful, the message ERR appears on the display for
about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or ERR screen to the normal timekeeping
screen by pressing D.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the Last
Signal screen.
2. Hold down A until the receiving indicator and current
auto receive setting ( or ) start to flash.
This is the setting screen.
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on ( ) and off
( ).
4. Press A to exit the setting screen.
• For information about city codes that support signal receive, see “To specify your
Home City”.
To display the Last Signal screen
In the Timekeeping Mode, press D to display the Last Signal screen (indicated by
GET). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
Day of week
Home Time
(Hour : Minutes Seconds)
Month – Day
Receive time
Receive date
Year
PM indicator
Current Time and Date Screen Last Signal Screen
Press .
DST indicator
Receiving indicator
Receiving indicator
On/Off Status
Page: 2
Operation Guide 3140
3
To set the alarm time
1. In the Alarm Mode, hold down A until the hour setting
of the alarm time starts to flash, which indicates the
setting screen.
• This automatically turns on the alarm.
2. Press C to move the flashing between the hour and
minute settings.
3. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds (in all modes), or until you
stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press D to cycle through the settings shown below.
Alarm Off
Signal On
Alarm On
Signal Off
Alarm Off
Signal Off
Alarm On
Signal On
Alarm On Indicator / Hourly Time Signal On Indicator
• The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Signal Reception Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem Probable Cause What you should do
Cannot perform
manual receive.
• The watch is not in the Timekeeping Mode.
• Your current Home City is not one of the
following city codes:
HNL, ANC, YVR, LAX, YEA, DEN, MEX,
YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS,
LON, MAD, PAR, ROM, BER, STO, ATH, or
MOW.
• The countdown timer is running.
• Enter the Timekeeping Mode
and try again.
• Select one of the cities to the
left as your Home City.
• Stop the countdown timer
and try again.
Auto receive is
turned on, but the
Level 3 receiving
indicator does
not appear on the
display.
• You changed the time setting manually.
• The watch was not in the Timekeeping or
World Time Mode, or you performed some
button operation during the auto receive
operation.
• Even if receive is successful, the Level 3
receiving indicator disappears every day
when the first auto receive operation of the
day is performed.
• Time data (hour, minutes, seconds) only was
received during the last receive operation.
The Level 3 receiving indicator appears only
when time data and date data (year, month,
day) are both received.
• Perform manual signal
receive or wait until the next
auto signal receive operation
is performed.
• Perform manual signal
receive or wait until the next
auto signal receive operation
is performed.
• Check to make sure the
watch is in a location where
it can receive the signal.
Time setting is
incorrect
following signal
reception.
• If the time is one hour off, the DST setting
may be incorrect.
• The Home City code setting is not correct for
the area where you are using the watch.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
• For further information, see “Important!” and “Radio-controlled Atomic Timekeeping
Precautions”.
World Time
The World Time Mode shows you the current time in 48
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check
your Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
While in the World Time Mode, press D to scroll
eastward through the city codes (time zones).
• For full information on city codes, see the “City Code
Table”.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• The DST indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
Countdown Timer
You can set the countdown timer within a range of one
to 60 minutes. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
To set the countdown start time
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the procedure under “To use the
countdown timer” to display it.
2. While a setting is flashing, use D (+) and B (–) to change it.
3. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you stop it by pressing any button. The countdown time is reset automatically to its
starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
City code
Current time in
selected city
Timekeeping Mode time
UTC offset
DST indicator
Timekeeping Mode time
(Hour : Minutes Seconds)
Minutes Seconds
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Split Time
Two Finishes
Stop Re-start Stop Clear
Start
Start Split
(SPL displayed)
Split release Stop Clear
Start Split Stop Split release Clear
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Timekeeping Mode time
(Hour : Minutes Seconds)
Minutes
Seconds
1/100 second
Alarm
After you set (and turn on) the daily alarm, the alarm tone
sounds when the alarm time is reached. You can also turn
on an Hourly Time Signal that causes the watch to beep
for about one second every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Timekeeping Mode time
(Hour : Minutes Seconds)
Alarm time
(Hour : Minutes)
Alarm on indicator
Hourly time signal on
indicator
Page: 3
Operation Guide 3140
4
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• When setting the time, you can also configure settings for the City Code, the DST
setting, the 12/24-Hour Format, Year, Month, Day, the Language setting, and the
Month/Day display format.
• Pressing D in the Timekeeping Mode will display the Last Signal screen.
Current Time and Date Screen Last Signal Screen
Day of week
Home Time
(Hour : Minutes Seconds)
Month – Day
Receive time
Receive date
Year
PM indicator DST indicator
Press .
Note
• This watch is capable of displaying text for the day of the week in any one of
nine different languages (English, Spanish, French, Portuguese, German, Italian,
Chinese, Russian, and Japanese).
Setting the Time and Date
Make sure you select your Home City code before you change the current time
and date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the time and date
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C to change the flashing contents in the
sequence shown below to select other settings.
City code
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the digital display.
To turn off Auto Display
Press any button to turn off Auto Display. This returns to the Timekeeping Mode.
To turn on Auto Display
In the Timekeeping Mode, while holding down B, hold down D for about two
seconds until the watch beeps.
Note
• Calibration signal reception is disabled while Auto Display is being performed.
• Auto Display cannot be performed while a setting screen is on the display.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on (MUTE not displayed) and off (MUTE displayed).
• Since the C button is also the mode change button, holding it down to turn the
button operation tone on or off also causes the watch’s current mode to change.
• The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Auto Return Features
• If you leave the watch with the Last Signal screen in the Timekeeping Mode for one
or two minutes without performing any operation, it returns to the Current Time and
Date screen in the Timekeeping Mode automatically.
• If you leave the watch in the Alarm Mode for two or three minutes without performing
any operation, it returns to the Timekeeping Mode automatically.
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch exits the setting screen automatically.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data. In most cases, holding down these buttons during a scroll operation
scrolls through the data at high speed.
Initial Screens
• When you enter the World Time or Alarm Mode, the data you were viewing when
you last exited the mode appears first.
Radio-controlled Atomic Timekeeping Precautions
• The display of the watch is blank while an auto receive operation is in progress.
• Strong electrostatic charge can result in the wrong time being set.
• The time calibration signal is bounced off the ionosphere. Because of this, such
factors as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
• The watch is designed to update the date and day of the week automatically for
the period January 1, 2000 to December 31, 2099. Setting of the date by a time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• Normally, the signal reception date shown by the Last Signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the Last Signal screen shows the date as kept in the Timekeeping Mode at
the time of signal reception.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time with the precision noted in “Specifications”.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code, DST (summer
time), and auto receive settings. The following are the initial factory defaults for
these settings.
Setting Initial Factory Default
City code (New York)
DST (summer time) (Auto switching)
Auto receive (Auto receive)
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
• The times for the Timekeeping Mode and all the city codes of the World Time Mode
are calculated in accordance with each city’s UTC offset.
• The UTC offset is a value that indicates the time difference between a reference
point in Greenwich, England and the time zone where a city is located.
• The letters “UTC” is the abbreviation for “Coordinated Universal Time”, which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
MUTE indicator
DST
City
Code Seconds
12/24-Hour
Format
Minutes
Day
Month/Day
Display Format Month
Language Year
Hour
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Screen: To do this: Do this:
Change the city code
Use D (east) and
B (west).
Cycle between auto DST ( ),
Standard Time ( ), and Daylight
Saving Time ( )
Press D.
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Press D.
Reset the seconds to Press D.
Change the hour, minutes, or year
Use D (+) and B (–).
Change the month or day
Change the language
ENG: English ESP: Spanish FRA: French
POR: Portuguese DEU: German
ITA: Italian CHN: Chinese : Russian
JPN: JapaneseRussian
Use D and B.
Toggle the month/day display format between
month/day (M/D) and day/month (D/M).
Press D.
• See the “City Code Table” for a complete list of available city codes.
• See the “Day of the Week List” for information on abbreviations used.
• Auto DST ( ) can be selected only while HNL, ANC, YVR, LAX, YEA,
DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, LON, MAD, PAR,
ROM, BER, STO, ATH, or MOW is selected as the Home City code. For more
information, see “Daylight Saving Time (DST)” below.
4. Press A to exit the setting screen.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signals transmitted from Fort Collins (the United States) or
Anthorn (England) includes both Standard Time and DST data. When the Auto DST
setting is turned on, the watch switches between Standard Time and DST (summer
time) automatically in accordance with the received time signal.
• The default DST setting is Auto DST ( ) whenever you select ANC, YVR,
LAX, YEA, DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, LON, MAD,
PAR, ROM, BER, STO, ATH, or MOW as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it
probably is best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
Auto DST
( )
DST on
( )
DST off
( )
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Page: 4
Operation Guide 3140
5
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• With the 12-hour format, the PM indicator (P) appears on the display for times in
the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Illumination
This watch has an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. In any mode (except when a setting screen is on the
display), press B to illuminate the display for about three seconds.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Illumination may be hard to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This
is due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
• Based on data as of June 2007.
• The rules governing global times (GMT differential and UTC offset) and summer time are determined by
each individual country.
* In December 2007, Venezuela changed its offset from –4.0 to –4.5. Note, however, that this watch
displays an offset of –4.0 (the old offset) for the CCS (Caracas, Venezuela) city code.
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Winnipeg
Chicago
Miami
Toronto
New York
Caracas
Halifax
St. Johns
Rio De Janeiro
Praia
Lisbon
London
Madrid
Paris
Rome
Berlin
Stockholm
Athens
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
–11.0
–10.0
–09.0
–08.0
–07.0
–06.0
–05.0
–04.0
–03.5
–03.0
–01.0
+00.0
+01.0
+02.0
+03.0
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
+08.0
+09.0
+09.5
+10.0
+11.0
+12.0
Papeete
Nome
San Francisco, Las Vegas,
Seattle/Tacoma, Dawson City
El Paso
Houston, Dallas/Fort Worth, New Orleans
Montreal, Detroit, Boston,
Panama City, Havana, Lima, Bogota
La Paz, Santiago, Port Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
Dublin, Casablanca, Dakar, Abidjan
Milan, Amsterdam, Algiers, Hamburg, Frankfurt, Vienna
Helsinki, Istanbul, Beirut, Damascus,
Cape Town
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata, Colombo
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Manila, Perth, Ulaanbaatar
Pyongyang
Darwin
Melbourne, Rabaul
Port Vila
Christchurch, Nadi, Nauru Island
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
YWG
CHI
MIA
YTO
NYC
CCS*
YHZ
YYT
RIO
RAI
LIS
LON
MAD
PAR
ROM
BER
STO
ATH
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
City City UTC Other major cities in same time zone
Code Differential
City Code Table
Sunday
ENG
ESP
FRA
POR
DEU
ITA
CHN
JPN
Monday Tuesday Wednesday Thursday Friday Saturday
SUN MON TUE WED THU FRI SAT
DOM LUN MAR MIE JUE VIE SAB
DIM LUN MAR MER JEU VEN SAM
DOM SEG TER QUA QUI SEX SAB
SON MON DIE MIT DON FRE SAM
DOM LUN MAR MER GIO VEN SAB
Day of the Week List

Question & answers

There are no questions about the Casio Waveceptor WV200A-1AV yet.

Ask a question about the Casio Waveceptor WV200A-1AV

Have a question about the Casio Waveceptor WV200A-1AV but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Casio Waveceptor WV200A-1AV. Please make sure that you describe your difficulty with the Casio Waveceptor WV200A-1AV as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.