Casio Privia PX-350M manual

View a manual of the Casio Privia PX-350M below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Casio
  • Product: Digital piano
  • Model/name: Privia PX-350M
  • Filetype: PDF
  • Available languages: Dutch, German, English

Table of Contents

Page: 1
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important!
Please note the following important information before using this product.
• Before using the AD-A12150LW Adaptor to power the product, be sure to check the AC Adaptor for any damage first. Carefully check the power
cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged.
• The product is not intended for children under 3 years.
• Use only the CASIO AD-A12150LW adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.
When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For that purpose, locate
the apparatus in a way that secures easy access to the power cord.
Declaration of Conformity
Model Number: PX-3
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Manufacturer:
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
This mark applies in EU countries only.
Page: 2
E-1
English
Contents
General Guide...........................E-2
Installing the Music Stand........................................... E-3
PX-3 Configuration ..................................................... E-4
Modes......................................................................... E-6
Saving Settings and Using Panel Lock....................... E-7
Returning the Digital Piano to Its
Factory Default Settings ............................................. E-7
Power Outlet .............................E-8
Using an AC Adaptor.................................................. E-8
Connections..............................E-9
Connecting Headphones ............................................ E-9
Connecting a Pedal .................................................... E-9
Connecting Audio Equipment or an Amplifier ........... E-10
Bundled and Optional Accessories........................... E-10
Selecting and
Playing a Tone........................E-11
To turn on Digital Piano Power................................. E-11
Listening to Demo Tunes.......................................... E-11
Selecting a Tone....................................................... E-11
Layering and Splitting Tones .................................... E-12
Applying Effects to a Tone....E-17
Reverb and Chorus................................................... E-17
Pitch Bend Wheel ..................................................... E-17
Confirming Common
Parameter Settings.................E-18
Common Parameters Operations ............................. E-18
Common Parameter Settings ................................... E-20
Using the Assignable
Buttons....................................E-24
Applying Modulation to Notes (ASSIGNABLE 1)...... E-24
Applying Portamento to Notes (ASSIGNABLE 1/2) ... E-24
Changing the Rotary Effect Speed
(ASSIGNABLE 2)...................................................... E-24
By-passing the DSP (ASSIGNABLE 2) .................... E-25
Sending Control Changes (ASSIGNABLE 1/2) ........ E-25
Using the Digital Piano as a
MIDI Master Keyboard............E-26
External MIDI Device Connection............................. E-26
Specifying the Zone Configuration............................ E-26
Specifying What Each Zone Controls ....................... E-27
Zone Setups ............................................................. E-27
Editing Zone Parameters.......E-28
Zone Parameter Operations ..................................... E-28
Zone Parameter Settings.......................................... E-30
Using Registration Memory...E-34
Registration Data ......................................................E-34
Registration Memory Operations ..............................E-34
Saving Registration Memory Bank Data to a File .....E-36
Using the Function Menu ......E-38
Function Menu Operations........................................E-38
Function Menu Settings ............................................E-39
Playing Back a MIDI File ........E-41
MIDI File Playback Operations..................................E-41
Supported Operations During MIDI File Playback ....E-42
Creating a New Card Music Folder...........................E-44
Using a Memory Card ............E-46
Memory Card Operations..........................................E-46
Error Messages.........................................................E-48
Connecting to a Computer ....E-49
Minimum Computer System Requirements ..............E-49
Connecting the Digital Piano to Your Computer .......E-49
Transferring Data between the
Digital Piano and a Computer ...................................E-50
Reference................................E-52
Troubleshooting ........................................................E-52
Product Specifications...............................................E-54
Operating Precautions ..............................................E-55
Appendix.................................E-57
Tone List ...................................................................E-57
Drum Assignment List...............................................E-59
DSP Effect List..........................................................E-60
DSP Algorithm List....................................................E-61
MIDI Implementation Chart
Company and product names used in this
manual may be registered trademarks of others.
Page: 4
General Guide
E-3
English
• This manual uses the numbers and names below to refer to buttons and controllers.
Insert the bottom of the music stand into the
groove on the top of the Digital Piano’s
console.
* Installing the Music Stand
 VOLUME knob
 ZONE SELECTOR (LOWER 1), REPEAT button
 ZONE SELECTOR (LOWER 2), sREW button
 ZONE SELECTOR (UPPER 1), dFF button
 ZONE SELECTOR (UPPER 2), PAUSE button
 INT/EXT, PLAY/STOP button
 ZONE EDIT, PAGE, PART button
 ASSIGNABLE 1 button
 ASSIGNABLE 2 button
 EDIT, TEMPO button
 MASTER CONTROL, CARD PLAYER, LOAD/SAVE
button
 PARAMETER SELECTOR (TRANSPOSE, A) button
 PARAMETER SELECTOR (BEND RANGE, B)
button
 PARAMETER SELECTOR (BRILLIANCE, C) button
 PARAMETER SELECTOR (EQ ON/OFF, D) button
 Display
 TONE, REGISTRATION button
 FUNCTION button
 w/NO, q/YES button
 PIANO, 1 button
 ELEC PIANO 1, 2 button
 ELEC PIANO 2, 3 button
 CLAVI/VIBES, 4 button
 ORGAN, 5 button
 STRINGS/ENSEMBLE, 6 button
 GUITAR/BASS, 7 button
 OTHERS/GM, 8 button
 LAYER, EXIT button
 SPLIT, u button
 REVERB, i button
 CHORUS, ENTER button
 STORE, USB DEVICE MODE button
 SD CARD SLOT
 PITCH BEND wheel
 USB port
 MIDI OUT/IN terminals
 DAMPER, SOFT/SOSTENUTO PEDAL jacks
 DC 12V terminal
 LINE OUT R, L/MONO jacks
 LINE IN R, L/MONO jacks
 POWER button
 PHONES jacks
 Pedal connector
Page: 5
E-4
General Guide
Master Control Configuration
The PX-3 Digital Piano is a MIDI master keyboard that uses four zones (UPPER 1, UPPER 2, LOWER 1, LOWER 2)
to control the internal sound source (INT) and external MIDI devices (EXT). Each zone performs simultaneous
control over one internal sound source part and one external MIDI device channel (when both INT and EXT are
ON).
The target (INT/EXT) of each zone control can be turned on or off as desired using the  (INT/EXT) button. Zone
editing (page E-28) lets you configure detailed settings related to how each individual zone controls an internal
sound source and/or external MIDI device.
In the case of an internal sound source, zone editing can be performed to create sounds by selecting a DSP,
configuring DSP settings, editing tones, etc. Following sound creation, signals are output via an equalizer that
allows adjustment of centralized common parameter settings (page E-18).
NOTE
• Which of the four zones are available for use depends on the LAYER and SPLIT on/off status. For details, see
“Layering and Splitting Tones” (page E-12) and “Specifying the Zone Configuration” (page E-26).
PX-3 Configuration
CHORUS
REVERB
ACOUSTIC
RESONANCE
WAVE
GENERATOR
EFFECT
3
EFFECT
2
EFFECT
1
X 36
DSP
X 2
EQUALIZER
DSP Acoustic Resonance Send
DSP Reverb Send
DSP Bypass
Thru
Part
DSP
DSP Chorus Send
Chorus Send
Reverb Send
Acoustic Resonance Send
Output
Page: 6
General Guide
E-5
English
Sound Source Configuration
The sound source is configured with a total of 36 parts: four parts that correspond to each of the zones, 16 parts for
MIDI file playback, and 16 parts that operate as the multi-timbre sound source during receipt of MIDI input.
The following shows the relationships between parts, ports, and MIDI channels.
Port 0 (Parts played by hand)
*1 MIDI OUT channel depends on zone editing (page E-28).
Port 1 (MIDI file playback parts)
Port 2 (MIDI IN parts)
NOTE
• MIDI messages output from the above Port 0 and Port 1 are grouped and sent from a single MIDI port. Port-
specific send is not supported.
Part Number MIDI Channel Part Name
1 IN:- - / OUT:01-16*1 Upper1
2 IN:- - / OUT:01-16*1 Upper2
3 IN:- - / OUT:01-16*1 Lower1
4 IN:- - / OUT:01-16*1 Lower2
Part Number MIDI Channel Part Name
17 IN:- - / OUT:01 Song01
...
...
...
32 IN:- - / OUT:16 Song16
Part Number MIDI Channel Part Name
33 IN:01 / OUT:- - Ext.01
...
...
...
48 IN:16 / OUT:- - Ext.16
Page: 7
E-6
General Guide
This Digital Piano has two main modes: a MASTER CONTROL mode and a CARD PLAYER mode. Each of these
modes has two sub-modes: a TONE mode and a REGISTRATION mode.
Use the MASTER CONTROL mode when playing the Digital Piano in a stand-alone configuration or when using it
as a MIDI master keyboard.
The setup of the MASTER CONTROL mode can be changed using common parameters (page E-18) and zone
parameters (page E-28).
Use the CARD PLAYER mode to play back a MIDI file. In the CARD PLAYER mode, you can play on the keyboard
along with MIDI file playback. Though the CARD PLAYER mode also supports control of an external MIDI device,
parameter settings cannot be configured.
Note that you should be aware of the Digital Piano’s current mode whenever performing an operation. Note the
following important points.
• The Digital Piano’s initial power on default mode is the MASTER CONTROL
mode’s TONE mode.
• Each press of the  (MASTER CONTROL/CARD PLAYER) button toggles
between the MASTER CONTROL and CARD PLAYER modes. You can
determine the current mode by noting which  (MASTER CONTROL/CARD
PLAYER) lamp is lit.
• Each press of the  (TONE/REGISTRATION) button toggles between the
TONE and REGISTRATION modes. You can determine the current mode by
noting which  (TONE/REGISTRATION) lamp is lit.
IMPORTANT!
• All of the operations in this user’s guide start from the initial power on default
state (MASTER CONTROL, TONE mode). If you start experiencing operation
problems, first try returning the Digital Piano to the MASTER CONTROL, TONE
mode. If you do not mind losing currently unsaved settings and data, simply
turn power off and then back on again.
NOTE
• The section title bars in this user’s guide also show the mode (MASTER CONTROL or CARD PLAYER, or both)
where the operations described in each section can be performed.
Modes
TONE mode
REGISTRATION mode
MASTER CONTROL mode
TONE mode
REGISTRATION mode
CARD PLAYER mode
Lit in the MASTER CONTROL mode.
Lit in the CARD PLAYER mode.
Lit in the TONE mode.
Lit in the REGISTRATION mode.
Page: 8
English
General Guide
E-7
Your Digital Piano lets you save its current settings,
and lock its buttons to protect against operation errors.
For details, see “Backup” and “Panel Lock” (page
E-40).
Perform the following procedure when you want to
return the Digital Piano’s stored data and settings to
their initial factory defaults.
1. Turn off the Digital Piano.
2. While holding down both the  (TONE) and
 (FUNCTION) buttons, press the
 (POWER) button.
• The Digital Piano will turn on and initialize its
internal system. You will be able to use the Digital
Piano in a short while.
NOTE
• See “To turn on Digital Piano Power” (page E-11) for
information about turning Digital Piano power on
and off.
Saving Settings and Using
Panel Lock
Returning the Digital Piano to
Its Factory Default Settings
Page: 9
E-8
Power Outlet
Your Digital Piano runs on standard household power.
Be sure to turn off power whenever you are not using
the Digital Piano.
Use only the AC adaptor (JEITA Standard, with unified
polarity plug) that comes with this Digital Piano. Use of
a different type of AC adaptor can cause malfunction.
Specified AC Adaptor: AD-A12150LW
• Use the supplied power cord to connect the AC
adaptor as shown in the illustration below.
Back
Note the following important precautions to avoid
damage to the power cord.
During Use
• Never pull on the cord with excessive force.
• Never repeatedly pull on the cord.
• Never twist the cord at the base of the plug or
connector.
• The power cord should not be stretched tight while
it is in use.
During Movement
• Before moving the Digital Piano, be sure to unplug
the AC adaptor from the power outlet.
During Storage
• Loop and bundle the power cord, but never wind it
around the AC adaptor.
IMPORTANT!
• Never connect the AC adaptor (JEITA Standard,
with unified polarity plug) that comes with this Digital
Piano to any other device besides this piano. Doing
so creates the risk of malfunction.
• Make sure the Digital Piano is turned off before
plugging in or unplugging the AC adaptor.
• The AC adaptor will become warm to the touch after
very long use. This is normal and does not indicate
malfunction.
Using an AC Adaptor
AC adaptor
Household power
DC 12V terminal
Power cord
Page: 10
E-9
English
Connections
IMPORTANT!
• Before connecting headphones, be sure to use the
Digital Piano’s  (VOLUME) knob to turn the
volume down to a low level. After connecting, you
can adjust the volume to the level you want.
Connect commercially available headphones to the
PHONES jacks. To protect your hearing, make sure
that you do not set the volume level too high when
using headphones.
The back of the Digital Piano has two pedal jacks, one
for a damper pedal and one for a soft/sostenuto pedal.
To connect to the pedal jack
Depending on the type of operation you want the
pedal (SP-3) to perform, connect the pedal’s cable
either to the Digital Piano’s DAMPER PEDAL jack or
SOFT/SOSTENUTO PEDAL jack. If you want to use
both operations (jacks) at the same time, you need to
purchase another optionally available pedal.
NOTE
• You can connect a pedal to the SOFT/SOSTENUTO
PEDAL jack and apply either a soft or sostenuto
effect to the notes you play. For details, see “Pedal
Assign” (page E-39).
Pedal Functions
 Damper Pedal
Pressing the damper pedal while playing will cause the
notes you play to reverberate for a very long time.
• Whenever a piano tone is selected, pressing this
pedal will activate the Digital Piano’s Acoustic
Resonance effect, which causes notes to resonate in
the same way they do when the damper pedal on an
acoustic piano is pressed. You can adjust the
acoustic resonance effect for each individual tone,
and you can apply it to other non-piano tones, if you
want. For details, see “Acoustic Resonance” (page
E-39) and “Acoustic Resonance Send” (page E-32).
 Soft Pedal
Pressing this pedal suppresses notes played on the
keyboard after the pedal was pressed, and makes them
sound softer.
 Sostenuto Pedal
Only the notes that are played while this pedal are
depressed are sustained until the pedal is released.
Pedal Connector
You can connect the optionally available 3-Pedal Unit
(SP-32) to the pedal connector on the bottom of the
Digital Piano. You can then use the pedals for
expression that is similar to that available on an
acoustic piano.
NOTE
• The SP-32 Pedal Unit supports half-pedal operation
(pressing the pedal part way). You can adjust the
amount of the effect is applied when the damper
pedal is pressed part way. For details, see “Half
Pedal Effect” (page E-39).
• The optionally available CS-67P special stand is
required in order to use the SP-32 Pedal Unit.
Connecting Headphones
Connecting a Pedal
PHONES jacks
Commercially available
headphones
Mini plug
Left Side
PEDAL jacks
SP-3
Back
Pedal connector
Bottom
Page: 11
E-10
Connections
This Digital Piano outputs notes from its LINE OUT R
(right channel output) and LINE OUT L/MONO (left
channel output). Connect a keyboard amplifier or other
device to direct output to speakers. You can adjust the
LINE OUT volume level with the Digital Piano’s
 (VOLUME) knob.
IMPORTANT!
• Whenever connecting something to the Digital
Piano, first use the  (VOLUME) knob to set the
volume to a low level. After connecting, you can
adjust the volume to the level you want.
• Whenever you connect any device to the Digital
Piano, be sure to read the user documentation that
comes with the device.
To output to a musical instrument
amplifier (Figure )
Use a commercially available connecting cord to
connect the amplifier to the Digital Piano’s LINE OUT
L/MONO jack as shown in Figure . Connecting a
cord to LINE OUT L/MONO only will cause the left
and right channels to be mixed and output as mono.
To output to audio equipment (Figure )
Use commercially available connection cords to
connect as shown in Figure . Normally, you should
set the input selector of the audio equipment to the
terminal where the Digital Piano is connected (AUX
IN, etc.).
To input from audio equipment (Figure )
LINE IN R jack input is output from the LINE OUT R
jack, and LINE IN L/MONO input is output from
LINE OUT L/MONO. Use commercially available
connection cords that match the equipment being
connected to. Connecting a cord to LINE IN L/MONO
only will cause the left and right channels to be mixed
and output from both LINE OUT R and LINE OUT L/
MONO.
NOTE
• Input from LINE IN R and LINE IN L/MONO is
output as-is from LINE OUT R and LINE OUT L/
MONO. The Digital Piano’s  (VOLUME) knob
setting does not affect this output.
Use only accessories that are specified for use with this
Digital Piano.
Use of unauthorized accessories creates the risk of fire,
electric shock, and personal injury.
NOTE
• You can get information about accessories that are
sold separately for this product from the CASIO
catalog available from your retailer, and from the
CASIO website at the following URL.
http://world.casio.com/
Connecting Audio Equipment
or an Amplifier
INPUT 1
INPUT 2
Guitar amplifier
Keyboard amplifier, etc.
Standard plug
Standard jack
LEFT (White)
RIGHT (Red)
Tape recorder,
MIDI sound source, etc.
Audio amplifier AUX IN jack, etc.
Pin plug
Bundled and Optional
Accessories
Page: 12
E-11
English
Selecting and Playing a Tone
1. After ensuring that the  (POWER) button is
in the off position, connect the AC adaptor to
the Digital Piano.
• For information about connecting the AC adaptor,
see “Power Outlet” (page E-8).
2. Rotate the  (VOLUME) knob towards MIN
to set the volume to a low level.
3. Connect headphones or other devices to the
Digital Piano as necessary (see
“Connections” on page E-9).
4. Press the  (POWER) button to turn on the
Digital Piano.
• The Digital Piano display screen will appear as
shown below, which indicates that it is ready to play
(using initial power on default settings).
• To turn off the Digital Piano, press the  (POWER)
button again.
IMPORTANT!
• Normally, turning power off and then back on again
will return the Digital Piano to its initial power on
default settings. If you perform the backup operation
(page E-40), turning power back on again will restore
the backed up settings. Perform a backup (page
E-40) or registration operation (page E-34) to save
the keyboard setup if you need to restore it later.
1. While holding down the  (PART) button,
press the  (PLAY/STOP) button.
• This starts demo tune play.
• The Digital Piano has a total of four demo tunes. You
can use the  buttons to jump the beginning of the
previous (q) or next (w) demo tune. You can use
the Tone Group buttons ( to ) to select a specific
demo tune.
• You can play along on the keyboard with demo tune
play. Note, however, that you cannot change the tone
assigned to the keyboard. Only the key operations
described above are supported.
2. To stop demo tune playback, press the 
(PLAY/STOP) button again.
Your Digital Piano comes with 250 tones (which
include 10 drum sets) built in. Tones are divided into
the eight tone groups shown below.
Use the following procedure to select a single tone that
is applied across the entire keyboard.
To select a tone
1. Use the “Tone List” (page E-57) to look up the
group and the number of the tone you want to
select.
2. Check to make sure that the lamp above the
 (MASTER CONTROL) button is lit.
• If it is unlit, press the  (MASTER CONTROL)
button to light it.
3. Check to make sure that the both the 
(LAYER) and  (SPLIT) button lamps are
unlit.
• If they are lit, press the  (LAYER) and/or 
(SPLIT) buttons to turn off both lamps.
4. If the  (UPPER 1) button lamp is unlit,
press the  (UPPER 1) button so its lamp is
lit.
To turn on Digital Piano Power
 button
Off position On position
Left Side
Listening to Demo Tunes
Selecting a Tone
MASTER CONTROL
Page: 13
E-12
Selecting and Playing a Tone
5. Check to make sure that the lamp above the
 (TONE) button is lit.
• If it is unlit, press the  (TONE) button to light the
upper lamp.
6. Use the  to  (Tone Group) buttons to
select the group you want.
• The lamp of the button you press will light.
7. Use the  (w, q) buttons to select the
tone you want. Now you can play on the
keyboard using the tone you selected.
Example: To select the “Jazz Organ 2” tone in the
“ORGAN” group
NOTE
• Pressing w and q at the same time selects tone
001 in the currently selected group.
• Holding down w or q will scroll through tones at
high speed.
• Holding down the  (FUNCTION) button as you
press w or q will jump 10 tones.
You can configure the keyboard so it plays two
different tones at the same time (Layer) or to play
different tones in the left and right ranges (Split). You
can even use Layer and Split in combination with each
other.
The following describes the various possible Layer and
Split combinations.
 One tone across the entire keyboard (page E-11)
Use zone UPPER 1.
 Two layered tones across the entire keyboard (page
E-13)
Use zones UPPER 1 and UPPER 2 at the same time.
 Two tones, one for the left range and one for the
right range of the keyboard (page E-14)
Use zones UPPER 1 and LOWER 1 at the same time.
 Four tones, two layered for the left range and two
layered for the right range of the keyboard (page
E-15)
Use zones UPPER 1, UPPER 2, LOWER 1, and
LOWER 2 at the same time.
 Three tones, one for one range and two layered for
the other range of the keyboard (page E-16)
Use all four zones at the same time, but with one
zone’s sound turned off by configuring one of the
zones with INT OFF to disconnect the internal sound
source. The example below shows INT OFF
configured for LOWER 2.
Lit
Tone number Tone name
Layering and Splitting Tones
UPPER 1
UPPER 1 INT ON
LAYER OFF
SPLIT OFF
UPPER 1
UPPER 2
UPPER 1/2 INT ON
LAYER ON
SPLIT OFF
LOWER 1 UPPER 1
UPPER 1/LOWER 1 INT ON
LAYER OFF
SPLIT ON
LOWER 1 UPPER 1
LOWER 2 UPPER 2
UPPER 1/2 INT ON
LOWER 1/2 INT ON
LAYER ON, SPLIT ON
LOWER 1
UPPER 1
UPPER 2
UPPER 1/2, LOWER 1 INT ON
LOWER 2 INT OFF
LAYER ON, SPLIT ON
Page: 14
English
Selecting and Playing a Tone
E-13
IMPORTANT!
• You can select a tone for each zone in both the
MASTER CONTROL and CARD PLAYER modes.
Note however that some procedures and operations
(lamp lighting status) when a tone is selected for
each zone in the CARD PLAYER mode are different
from those in the case of the MASTER CONTROL
mode.
Here, explanations are based on selecting a tone for
each zone in the MASTER CONTROL mode. For
information about selecting tones in the CARD
PLAYER mode, see “To select a tone for each zone
in the CARD PLAYER mode” (page E-44).
NOTE
• When using Layer and/or Split to play more than
one tone at the same time, you can adjust the volume
balance of each zone, perform octave shift for each
zone, and configure detailed settings for the effects
applied to zones. For details about parameters that
can be configured and setting procedures, see
“Editing Zone Parameters” (page E-28).
Layering Two Tones
1. Use the “Tone List” (page E-57) to look up the
group(s) and numbers of the two tones
(UPPER 1 zone tone and UPPER 2 zone
tone) you want to use.
2. Check to make sure that the both the 
(LAYER) and  (SPLIT) button lamps are
unlit.
• If one or both lamps are lit, press the  (LAYER) and
 (SPLIT) buttons to turn them off.
3. Press the  (UPPER 1) button so its lamp is
lit.
• This indicates you can select the UPPER 1 zone tone.
4. Select the UPPER 1 zone tone.
• For details about selecting tones, see “To select a
tone” (page E-11).
5. Press the  (LAYER) button so its lamp is lit.
• At this time the  (UPPER 1) button lamp will go out
and the  (UPPER 2) button lamp will light in its
place. This indicates you can select the UPPER 2 zone
tone.
6. Select the UPPER 2 zone tone.
7. Play something on the keyboard to check
how the tones sound layered together.
• At any time you can press the  (UPPER 1) button to
change the UPPER 1 zone tone or the  (UPPER 2)
button to change the UPPER 2 zone tone.
8. To cancel tone layering, press the 
(LAYER) button again so its lamp goes out.
UPPER 1
UPPER 2
Lit
Lit
Lit
Unlit
Page: 15
E-14
Selecting and Playing a Tone
Splitting the Keyboard between Two
Tones
1. Use the “Tone List” (page E-57) to look up the
group(s) and numbers of the two tones
(UPPER 1 zone tone and LOWER 1 zone
tone) you want to use.
2. Check to make sure that the both the 
(LAYER) and  (SPLIT) button lamps are
unlit.
• If one or both lamps are lit, press the  (LAYER) and
 (SPLIT) buttons to turn them off.
3. Press the  (UPPER 1) button so its lamp is
lit.
• This indicates you can select the UPPER 1 zone tone.
4. Select the UPPER 1 zone tone.
• For details about selecting tones, see “To select a
tone” (page E-11).
5. Press the  (SPLIT) button so its lamp is lit.
• At this time the  (UPPER 1) button lamp will go out
and the  (LOWER 1) button lamp will light in its
place. This indicates you can select the LOWER 1
zone tone.
6. Select the LOWER 1 zone tone.
7. Play something on the left and right sides of
the keyboard to confirm that the tones are
assigned properly.
• At any time you can press the  (UPPER 1) button to
change the UPPER 1 zone tone or the  (LOWER 1)
button to change the LOWER 1 zone tone.
8. To cancel the keyboard split, press the 
(SPLIT) button again so its lamp goes out.
NOTE
• You also can specify the keyboard split point, which
the location where the keyboard splits between the
left range and right range. In initial default split
point is at key F#3.
For details, see “To specify the keyboard split point”
(page E-14).
To specify the keyboard split point
1. Hold down the  (SPLIT) button until the
screen shown below appears.
2. Press the keyboard key that you want to be
the leftmost key in the right side (UPPER 1
zone) range.
• The name of the key you press will appear on the
display as the new split point key name.
• You also can use the  (w, q) buttons to change
the split point key name.
3. When you are finished, press the  (SPLIT)
button.
LOWER 1 UPPER 1
Lit
Unlit
Lit
Lit
LOWER 1 zone
Split point
UPPER 1 zone
Current split point key name
Page: 16
English
Selecting and Playing a Tone
E-15
To use layer and split together
1. Use the “Tone List” (page E-57) to look up the
group(s) and numbers of the tones (UPPER 1,
UPPER 2, LOWER 1, and LOWER 2 zone
tones) you want to use.
2. Check to make sure that the both the 
(LAYER) and  (SPLIT) button lamps are
unlit.
• If one or both lamps are lit, press the  (LAYER) and
 (SPLIT) buttons to turn them off.
3. Press the  (UPPER 1) button so its lamp is
lit.
• This indicates you can select the UPPER 1 zone tone.
4. Select the UPPER 1 zone tone.
• For details about selecting tones, see “To select a
tone” (page E-11).
5. Press the  (LAYER) button so its lamp is lit.
• This will cause the  (UPPER 2) button lamp to
light. This indicates you can select the UPPER 2 zone
tone.
6. Select the UPPER 2 zone tone.
7. Press the  (LAYER) button so its lamp is
unlit.
8. Press the  (SPLIT) button so its lamp is lit.
• This will cause the  (LOWER 1) button lamp to
light. This indicates you can select the LOWER 1 zone
tone.
9. Select the LOWER 1 zone tone.
10. Press the  (LAYER) button so its lamp is lit.
• This will cause the  (LOWER 2) button lamp to
light. This indicates you can select the LOWER 2 zone
tone.
11. Select the LOWER 2 zone tone.
12. Play something on the left and right sides of
the keyboard to confirm that the tones are
assigned and layered properly.
• You can change any of the zone tones at any time by
performing one of the operations shown below.
LOWER 1 UPPER 1
LOWER 2 UPPER 2
Lit
Lit
Lit
Unlit
To change this
zone’s tone:
Do this:
UPPER 1 zone Press the  (UPPER 1) button and
then select a tone.
UPPER 2 zone Press the  (UPPER 2) button and
then select a tone.
LOWER 1 zone Press the  (LOWER 1) button and
then select a tone.
LOWER 2 zone Press the  (LOWER 2) button and
then select a tone.
Lit
Lit
Lit
Lit
Page: 17
E-16
Selecting and Playing a Tone
13. To cancel layer and split, press  (LAYER)
and  (SPLIT) buttons again so their lamps
go out.
NOTE
• When using Layer and Split at the same time, you
can switch to only a single tone in either of the
keyboard ranges by configuring INT OFF for the
zone whose tone you do not want to sound. For
example, you could perform the steps below to
sound zones UPPER 1, UPPER 2, and LOWER 1,
without sounding the LOWER 2 zone.
• Pressing the  (UPPER 1),  (UPPER 2),
 (LOWER 1) or  (LOWER 2) button causes the
lamp of the pressed button to light, and the lamps of
the other buttons to go out. At this time, the tone
name of the zone whose button you press will
appear on the display, and you can change the tone,
if you want. However, the tones that sound when a
keyboard keys are pressed depend on the current
Layer and Split on/off settings.
• The  (INT/EXT) button is for specifying what each
zone controls (INT = internal sound source, EXT =
external MIDI device). The INT (left) side lamp
indicates internal sound source control on/off, while
the EXT (right) side indicates external MIDI device
control on/off. For details about this button, see
“Using the Digital Piano as a MIDI Master
Keyboard” (page E-26).
1. Press the  (LOWER 2) button so its lamp is lit.
2. Press the  (INT/EXT) button twice so the INT
side (left side) lamp goes out.
LOWER 1
UPPER 1
UPPER 2
Lit
Unlit
Page: 18
E-17
English
Applying Effects to a Tone
Your Digital Piano provides four types of reverb and
four types of chorus. The reverb and chorus functions
have their own dedicated keys for easy on/off
operation.
• Each press of the  (REVERB) button toggles
reverb on and off. The lamp above the button is lit
when reverb is on, and unlit when it is off.
• Each press of the  (CHORUS) button toggles
chorus on and off. The lamp above the button is lit
when chorus is on, and unlit when it is off.
IMPORTANT!
• Under initial default settings of certain tones, chorus
is not applied simply by turning chorus on. This is
because the initial default value of the chorus send
setting is 0. To apply chorus, change the chorus
send value of the zone where you want to use it. For
details, see “Effect Settings” (page E-32).
NOTE
• The reverb and chorus on/off setting is applied to all
zones, but reverb send and chorus send settings can
be configured for individual zones. For details, see
“Effect Settings” (page E-32).
To change the reverb type
1. Hold down the  (REVERB) button until the
screen shown below appears.
2. Use the  (w, q) buttons to select the
reverb type you want.
• You can select one of the following reverb types:
 Room,  Hall,  Large Hall,  Stadium.
3. When you are finished, press the 
(REVERB) button.
To change the chorus type
1. Hold down the  (CHORUS) button until the
screen shown below appears.
2. Use the  (w, q) buttons to select the
chorus type you want.
• You can select one of the following chorus types:
 Light Chorus,  Chorus,  Deep Chorus,
 Flanger.
3. When you are finished, press the 
(CHORUS) button.
The  (PITCH BEND) wheel lets you
change the pitch of notes you are playing
by rotating the wheel forward or back.
Rotating the wheel away from you raises
the pitch, while rotating it towards you
lowers it. Releasing the wheel causes the
pitch of the notes to return to normal
automatically.
IMPORTANT!
• Do not have the pitch bend wheel rotated as you turn
on the Digital Piano.
NOTE
• You also can change the range of the pitch bend
wheel. See “Bend Range” (page E-20).
Reverb and Chorus
Pitch Bend Wheel
MASTER CONTROL CARD PLAYER
Page: 19
E-18
Confirming Common Parameter Settings
Common parameters include transpose, bend range, equalizer, and other global parameters. Common parameters
also include the settings of the function assigned to the ASSIGNABLE buttons.
The common parameter settings appear on the common menu that appears first whenever you turn on the Digital
Piano.
• The common menu has five pages. Press the  (PAGE) button to scroll through the pages.
• Each common menu page includes up to four parameters, each of which corresponds one of the PARAMETER
SELECTOR buttons ( (A) through  (D)).
• The “COMMON PARAMETER” list in the upper left of the Digital Piano’s control panel shows the parameters
assigned to each of the PARAMETER SELECTOR buttons.
Common Parameters Operations
Common menu
Page
Parameter Name
Settings
MASTER CONTROL
Page: 20
English
Confirming Common Parameter Settings
E-19
To change common parameter settings
1. Check to make sure that the lamp above the
 (MASTER CONTROL) button is lit.
• If it is unlit, press the  (MASTER CONTROL)
button to light it.
2. Check to make sure that the lamp above the
 (ZONE EDIT) button is unlit.
• If the lamp is lit, hold down the  (ZONE EDIT)
button until it goes out.
3. Use the  (PAGE) button to display the
common menu page that contains the
parameter whose setting you want to change.
Example: Common menu page 2
• Each press of the  (PAGE) button advances to the
next page.
4. Press the PARAMETER SELECTOR button
( (A) through  (D)) to select the
parameter whose setting you want to change.
• The brackets around the setting of parameter you
select will change from [ ] to %. This indicates
that editing of the setting is enabled.
Example: After the  (C) button is pressed
• Holding down one of the PARAMETER SELECTOR
buttons will display its full name. For example,
“LoMdG” will change to “LowMid Gain”.
5. Use the  (EDIT w, q) buttons to change
the setting.
• Pressing w and q at the same time returns the
setting to its initial default.
• Holding down w or q will scroll through the
settings at high speed.
• For details about the meaning and range of each
parameter setting, see “Common Parameter Settings”
(page E-20).
6. If you want to change the settings of other
parameters, repeat steps 3 through 5 of this
procedure.
IMPORTANT!
Turning off the Digital Piano causes all common
parameters to return to their initial default settings. If
you need to save a common parameter setup, perform
one of the operations described below.
• If you want to restore the current setup the next time
you turn on the Digital Piano, perform the backup
operation. For details, see “Backup” (page E-40).
• If you don’t need to restore the current setup the next
time you turn on the Digital Piano but want to have it
on hand for recall when you need it, save the setup
to registration memory. For details, see “Using
Registration Memory” (page E-34).
Lit
Page: 21
E-20
Confirming Common Parameter Settings
This section explains the meaning of each common parameter, and provides information about their setting ranges
and initial default values.
• In this section, each parameter is preceded by a number and a letter, like “1-A”. This indicates the common menu
page number (1) and the PARAMETER SELECTOR button you need to press to select it (A).
• The values following the description of a parameter are its setting range. The initial default setting is indicated by
an asterisk (*).
General Settings
Adjusts overall keyboard tuning by semitone units
–12 to 0* to 12 semitones
Specifies the range of pitch change that occurs when the pitch bend wheel is rotated.
0 to 2* to 12 semitones
Controls the brilliance of the tone. A greater value produces a brighter, harder sound, while a lower value produces
a mellower, softer sound.
–3 to 0* to 3
Equalizer Settings
These settings constitute a four-band equalizer for sound compensation.
Specifies whether sound output by the Digital Piano passes (ON) or does not pass (Off) through the equalizer.
OFF, ON*
Common Parameter Settings
■ 1-A Transpose (Trnsp)
■ 1-B Bend Range (BendR)
■ 1-C Brilliance (Brila)
■ 1-D EQ ON/OFF (EQ)
Page: 22
Confirming Common Parameter Settings
E-21
English
Assignable Button Settings
These settings specify the functions assigned to the  (ASSIGNABLE 1) and  (ASSIGNABLE 2) buttons.
Functions that can be assigned to each button are shown in the “ASSIGNABLE 1 TYPE” and “ASSIGNABLE 2
TYPE” lists on the control panel to the left of the ASSIGNABLE buttons.
NOTE
• Regardless of the settings you configure for the  (ASSIGNABLE 1) and  (ASSIGNABLE 2) buttons here, you
can use the zone editing procedure (page E-28) to enable or disable each individual zone. For details, see “Control
Settings” (page E-33).
■ 2-A to 3-D Band Gain and Frequency Settings
Parameter Name Location Description Settings (* indicates default)
Low Gain (LoG) 2-A Adjusts the low-range gain. –12 to 0* to 12
Low Freq. (LoF) 2-B Specifies the frequency of the low-range
adjusted by Low Gain.
0.2*, 0.4, 0.8 kHz
LowMid Gain
(LoMdG)
2-C Adjusts the low mid-range gain. –12 to 0* to 12
LowMid Freq.
(LoMdF)
2-D Specifies the frequency of the low mid-
range adjusted by LowMid Gain.
1.0*, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 kHz
HighMid Gain
(HiMdG)
3-A Adjusts the high mid-range gain. –12 to 0* to 12
HighMid Freq.
(HiMdF)
3-B Specifies the frequency of the high mid-
range adjusted by HighMid Gain.
1.0, 1.3, 1.6, 2.0, 2.5*, 3.2, 4.0, 5.0 kHz
High Gain (HiG) 3-C Adjusts the high gain. –12 to 0* to 12
High Freq. (HiF) 3-D Specifies the frequency of the high-range
adjusted by High Gain.
6.0, 8.0, 10* kHz
Page: 23
E-22
Confirming Common Parameter Settings
Specifies the function assigned to the  (ASSIGNABLE 1) button.
The following describes the functions that can be assigned by each setting.
Specifies the function assigned to the  (ASSIGNABLE 2) button.
The following describes the functions that can be assigned by each setting.
■ 4-A Assignable Button 1 Type (Asgn1)
Setting Assigned Functions
Modulation (Mod) This setting assigns modulation to the button.*1 The depth of the modulation is specified using the 
(B) and  (C) buttons.
Portamento (Por) This setting assigns portamento the button. When this function is assigned, portamento is applied
while the  (ASSIGNABLE 1) button is depressed and not applied while the button is released.*2
Control Change
Number 0 to 127
(CC# 000 to 127)
This setting assigns a control change number to the button. The MIDI channel for sending a control
change or the value sent when the  (ASSIGNABLE 1) button is pressed or released is specified
using the  (B),  (C), and  (D) buttons.
*1 To apply modulation only to a particular zone, select “001” (CC#1 = Modulation) as the Asgn1 instead of “Mod”.
Also, specify a control change send MIDI channel that matches the MIDI channel of the zone where you want to
apply modulation. For more information, see “Settings when Asgn1/Asgn2 = Control Change Number 0 to 127”
(page E-23).
*2 Portamento can be turned on or off for each zone. For details, see “Editing Tones” (page E-31).
■ 5-A Assignable Button 2 Type (Asgn2)
Settings Assigned Functions
Rotary (Rot) This function, which switches rotation speed, can be assigned for the rotary effect used by the DSP
(see “DSP Type” on page E-30). The speed is “Fast” when the  (ASSIGNABLE 2) button is on
(lamp lit) and “Slow” when it is off (lamp unlit).
Portamento (Por) This setting assigns portamento to the button. Portamento is applied when the  (ASSIGNABLE 2)
button is on, and not applied when it is off.*1
DSP Bypass (Dbp) This setting assigns a function that turns off the DSP of a particular zone. The zone whose DSP is
being turned off is specified with the  (B) button.
Control Change
Number 0 to 127
(CC# 000 to 127)
This setting assigns a control change number to the button. The MIDI channel for sending a control
change or the value sent when the  (ASSIGNABLE 2) button is on or off is specified using the 
(B),  (C), and  (D) buttons.
*1 Portamento can be turned on or off for each zone. For details, see “Editing Tones” (page E-31).
■ 4-B, 4-C Settings when Asgn1 = Modulation (Mod)
Parameter Name Location Description Settings (* indicates default)
Depth (Button OFF)
(OfDep)
4-B Specifies the modulation depth while the
button is not pressed.
0* to 127
Depth (Button ON)
(OnDep)
4-C Specifies the modulation depth while the
button is pressed.
0 to 127*
Page: 24
Confirming Common Parameter Settings
E-23
English
■ 4-B, 4-C, 4-D, 5-B, 5-C, 5-D Settings when Asgn1/Asgn2 = Control Change Number 0 to 127
Parameter Name Location Description Settings (* indicates default)
Channel (Ch) 4-B, 5-B Specifies the MIDI channel*1 for sending
control changes.
1* to 16
Value (Button OFF)
(OfVal)
4-C, 5-C Specifies the value sent when the button is
released (turned off).
0* to 127
Value (Button ON)
(OnVal)
4-D, 5-D Specifies the value sent when the button is
pressed (turned on).
0* to 127
*1 Control change information in principle is sent from the Digital Piano to an external destination over the MIDI
channel specified here. However, when a MIDI send channel of one of the Digital Piano’s zones matches the
channel specified here and that zone is configured as INT ON, control change information is sent for the internal
sound source that corresponds to that zone.
■ 5-B Settings when Asgn2 = DSP Bypass (Dbp)
Parameter Name Location Description Settings (* indicates default)
Zone 5-B This setting can be used to select the zone
(Up1: UPPER 1, Up2: UPPER 2,
Lo1: LOWER 1, Lo2: LOWER 2) that
bypasses the DSP (DSP off) when the 
(ASSIGNABLE 2) button is on (lamp lit).
Up1*, Up2, Lo1, Lo2
Page: 25
E-24
Using the Assignable Buttons
There are two assignable buttons named 
(ASSIGNABLE 1) and  (ASSIGNABLE 2). The 
(ASSIGNABLE 1) button is designed so it is on while
pressed and off while released. The 
(ASSIGNABLE 2) button toggles on (lamp lit) and off
(lamp unlit) each time it is pressed.
The main use of the assignable buttons is to perform
real-time operations, mainly for effects. You can
configure settings for the assignable button with the
common menu (page E-18).
NOTE
• For information about how to configure settings, see
“To change common parameter settings” (page
E-19).
• The “Common Parameter Information” and “Zone
Parameter Information” items in the explanations in
this section show where you need to go for
information about the parameters that come under
an assignable function.
Fixed-depth modulation is applied to notes while the
 (ASSIGNABLE 1) button is pressed or released.
Common Parameter Information:
Applying portamento causes the pitch to slide between
two notes played in succession. It is an effect that is
used with strings and woodwind instruments. With
the  (ASSIGNABLE 1) button, portamento is applied
while the button is pressed. With the 
(ASSIGNABLE 2) button, portamento is applied while
the button is on.
Common Parameter Information:
Zone Parameter Information:
When the rotary effect is being selected by DSP (page
E-30), each press of the  (ASSIGNABLE 2) button
toggles the rotation speed between fast and slow.
Common Parameter Information:
Zone Parameter Information:
Applying Modulation to Notes
(ASSIGNABLE 1)
4-A Assignable Button 1 Type (Asgn1) (page E-22)
4-B, 4-C Settings when Asgn1 = Modulation (Mod)
(page E-22)
Applying Portamento to Notes
(ASSIGNABLE 1/2)
4-A Assignable Button 1 Type (Asgn1) (page E-22)
5-A Assignable Button 2 Type (Asgn2) (page E-22)
4-C Portamento ON/OFF (Porta) (page E-31)
4-D Portamento Time (PTime) (page E-31)
Changing the Rotary Effect
Speed (ASSIGNABLE 2)
5-A Assignable Button 2 Type (Asgn2) (page E-22)
DSP Settings (page E-30)
MASTER CONTROL CARD PLAYER
Page: 26
English
Using the Assignable Buttons
E-25
While the  (ASSIGNABLE 2) button is on, only the
sound of a specified zone is output without passing
through the DSP.
Common Parameter Information:
NOTE
• For more information about DSP bypass, see the
flowchart under “Master Control Configuration”
(page E-4).
Since control change is a MIDI message, the target of a
send operation generally is an external MIDI device.*
With the  (ASSIGNABLE 1) button, different control
change values can be specified for sending at the points
the button is pressed and when it is released.
With the  (ASSIGNABLE 2) button, different control
change values can be specified for sending at the points
the button is turned on and when it is turned off.
Common Parameter Information:
* You also can configure control change send for the
internal sound source that corresponds to a
particular zone. See the note under “4-B, 4-C, 4-D,
5-B, 5-C, 5-D Settings when Asgn1/Asgn2 = Control
Change Number 0 to 127” (page E-23).
By-passing the DSP
(ASSIGNABLE 2)
5-A Assignable Button 2 Type (Asgn2) (page E-22)
5-B Settings when Asgn2 = DSP Bypass (Dbp) (page
E-23)
Sending Control Changes
(ASSIGNABLE 1/2)
4-A Assignable Button 1 Type (Asgn1) (page E-22)
5-A Assignable Button 2 Type (Asgn2) (page E-22)
4-B, 4-C, 4-D, 5-B, 5-C, 5-D Settings when Asgn1/
Asgn2 = Control Change Number 0 to 127 (page
E-23)
Page: 27
E-26
Using the Digital Piano as a MIDI Master
Keyboard
A unique MIDI channel can be assigned to each of the Digital Piano’s four zones (UPPER 1, UPPER 2, LOWER 1,
LOWER 2) to provide simultaneous control of up to four external MIDI devices.
IMPORTANT!
• This section provides only basic information about how to use the Digital Piano as a MIDI master keyboard. For
details about the MIDI specifications of this Digital Piano, see the “MIDI Implementation” document at the website
located at the URL below.
http://world.casio.com/
Your Digital Piano is equipped with standard 5-pin DIN connector type MIDI OUT and MIDI IN terminals. It is up
to you to purchase optionally available or commercially available MIDI cables when connecting to an external MIDI
device.
IMPORTANT!
• The MIDI terminals are disabled while the Digital Piano is connected to a computer via the USB port.
Press the  (LAYER) and  (SPLIT) buttons so their lamps are lit in one of the combinations shown below to
achieve the zone configuration you want.
NOTE
• You can change the ranges of the UPPER and LOWER zones using the procedure described under “To specify the
keyboard split point” (page E-14).
External MIDI Device Connection
Specifying the Zone Configuration
UPPER 1
LAYER unlit, SPLIT unlit
UPPER 1
UPPER 2
LAYER lit, SPLIT unlit
LOWER 1 UPPER 1
LAYER unlit, SPLIT lit
LOWER 1 UPPER 1
LOWER 2 UPPER 2
LAYER lit, SPLIT lit
MASTER CONTROL
Page: 28
Using the Digital Piano as a MIDI Master Keyboard
E-27
English
After you use the  (LAYER) and  (SPLIT) buttons to select a zone configuration, you can turn internal sound
source control (INT) and external MIDI device control (EXT) on or off as required for each zone. Use the  (INT/
EXT) button to specify what a zone controls.
To specify what a zone controls
1. Press the button that corresponds to the zone whose settings you want to change:  (UPPER 1)
button,  (UPPER 2) button,  (LOWER 1) button,  (LOWER 2) button.
• The lamp of the button you press will light.
2. Use the  (INT/EXT) button to specify what you want the zone you selected in step 1 to control.
• Pressing the  (INT/EXT) button cycles through the available settings, which are indicated by two lamps above the
button as illustrated below.
• The INT side lamp indicates the internal sound source, while the EXT side lamp indicates an external MIDI device. Keep
pressing the button until the lamp(s) of the device(s) you want the zone to control are lit.
3. If you want to configure other zones, repeat steps 1 and 2 of this procedure as required.
NOTE
• If you want to use the Digital Piano exclusively as an external MIDI device controller, you can turn off the local
control setting (page E-39), which severs the actual connection between its keyboard and the internal sound
source.
In addition to the MIDI channel, you can configure external MIDI device control settings and internal sound source
settings (tone selection, DSP settings) for each individual zone.
• For the procedure to use to select a tone for each zone, see “Layering and Splitting Tones” (page E-12).
• For information about configuring MIDI channel, mixer, DSP, and other detailed settings for each zone, see
“Editing Zone Parameters” (page E-28).
Specifying What Each Zone Controls
Zone Setups
Lit
Lit
Unlit
Lit
Lit
Unlit
Unlit
Unlit
Page: 29
E-28
Editing Zone Parameters
Your Digital Piano is a four-zone MIDI master keyboard (“Master Control Configuration”, page E-4). A zone is a
unit that controls the internal sound source and/or external MIDI device. Just as you can select a different internal
sound source tone for each zone, you also can specify a mixer, DSP and other settings for an internal sound source,
and you can specify a MIDI channel and other control settings for an external MIDI device.
The parameters whose settings can be configured for each zone are called “zone parameters.” To configure zone
parameter settings, enter the MASTER CONTROL mode and then hold down the  (ZONE EDIT) button until the
zone menu appears on the display.
• The zone menu has eight pages. Press the  (ZONE EDIT) button to scroll through the pages.
• Each zone menu page includes up to four parameters, each of which corresponds one of the PARAMETER
SELECTOR buttons ( (A) through  (D)).
• The format of the DPS settings on page 3 of the zone menu is a bit different from the other pages, as shown below.
• The “ZONE PARAMETER” list in the upper left of the Digital Piano’s control panel shows the zone parameters
assigned to each of the PARAMETER SELECTOR buttons.
Zone Parameter Operations
Zone Menu
Page
Parameter Name
Settings
MASTER CONTROL
Page: 30
English
Editing Zone Parameters
E-29
To change zone parameter settings
1. Check to make sure that the lamp above the
 (MASTER CONTROL) button is lit.
• If it is unlit, press the  (MASTER CONTROL)
button to light it.
2. Hold down the  (ZONE EDIT) button until
the zone menu screen shown below appears.
• This will cause the  (ZONE EDIT) button lamp to
light.
3. Use the  (ZONE EDIT) button to display the
zone menu page that contains the parameter
whose setting you want to change.
Example: Zone menu page 2
• Each press of the  (ZONE EDIT) button advances
to the next page.
4. Press the PARAMETER SELECTOR button
( (A) through  (D)) to select the
parameter whose setting you want to change.
• The brackets around the setting of parameter you
select will change from [ ] to %. This indicates that
editing of the setting is enabled.
Example: After the  (C) button is pressed
• Holding down one of the PARAMETER SELECTOR
buttons will display its full name. For example,
“MidCh” will change to “MIDI Out Ch”.
5. Press the button that corresponds to the zone
whose settings you want to change:
 (UPPER 1) button,  (UPPER 2) button,
 (LOWER 1) button,  (LOWER 2) button.
• The lamp of the button you press will light, which
indicates its zone is selected.
6. Use the  (EDIT w, q) buttons to change
the setting.
• Pressing w and q at the same time returns the
setting to its initial default.
• Holding down w or q will scroll through the
settings at high speed.
• For details about the meaning and range of each
parameter setting, see “Zone Parameter Settings”
(page E-30).
7. If you want to change the setting of the same
parameter in other zones, perform steps 5
and 6 again.
8. If you want to change the setting of another
parameter, perform steps 3 through 7 again
as required.
9. After all of the zone parameters are the way
you want, hold down the  (ZONE EDIT)
button until the button lamp goes out.
• This will return the menu along the bottom of the
display to the common menu.
IMPORTANT!
Turning off the Digital Piano causes all zone
parameters to return to their initial default settings. If
you need to save a zone parameter setup, perform one
of the operations described below.
• If you want to restore the current setup the next time
you turn on the Digital Piano, perform the backup
operation. For details, see “Backup” (page E-40).
• If you don’t need to restore the current setup the next
time you turn on the Digital Piano but want to have it
on hand for recall when you need it, save the setup
to registration memory. For details, see “Using
Registration Memory” (page E-34).
Lit
Page: 31
E-30
Editing Zone Parameters
This section explains the meaning of each zone
parameter, and provides information about their
setting ranges and initial default values.
• In this section, each parameter is preceded by a
number and a letter, like “1-A”. This indicates the
common menu page number (1) and the
PARAMETER SELECTOR button you need to press
to select it (A).
• In this section, the name of each zone parameter is
followed by and/or .
• The values following the description of a parameter
are its setting range. The initial default setting is
indicated by an asterisk (*).
Mixer Settings
Adjusts the volume level. 0 is mute, 127
is maximum volume.
0 to 127*
Adjusts the pan position. 0 specifies a
center pan position, a negative value
shifts it to the left, and a positive value shifts it to the
right.
–64 to 0* to +63
Shifts the pitch upwards or downwards
in octave steps. Changing this setting
also shifts the note number sent to an external MIDI
device.
–2 to 0* to +2
MIDI Settings
Specifies the MIDI channel used by each zone
when sending MIDI data.
1 to 16 (*UPPER 1: 1, UPPER 2: 2, LOWER 1: 3,
LOWER 2: 4)
Specifies the value of the bank MSB that is
appended when sending a program change
to an external destination with operation 2-D.
0* to 127
Specifies the value of the bank LSB that is
appended when sending a program change
to an external destination with operation 2-D.
0* to 127
Specifies the program change number sent to
an external destination. Any time this value
is changed, the corresponding numbered program
change is sent to an external destination (without
affecting the internal sound source).
0* to 127
DSP Settings
Selects tremolo, rotary, or some other DSP
type. The DSP type is indicated by “ton”
(which is the initial default for each tone) or a number
from 1 to 64. Any time the  (EDIT w, q) buttons
are used to switch the number, the DSP type name that
corresponds to the current number will appear on the
display.
The parameters displayed in 3-B depend on the DSP
type selected here.
In accordance with the DSP type selected in
3-A, displays the name of the parameters
whose settings can be configured. When there are
multiple parameters, you can use the  (EDIT w,
q) buttons to scroll through them. Perform the
operation under 3-C to change the setting of a
parameter.
Zone Parameter Settings
indicates a setting that applies to internal
sound source control.
indicates a setting that applies to external
MIDI device control.
■ 1-A Volume (Vol)
■ 1-B Pan
■ 1-C Octave Shift (Oct)
INT EXT
INT
EXT
INT / EXT
INT / EXT
INT / EXT
■ 2-A MIDI Out Channel (MidCh)
■ 2-B Bank MSB (BnkMS)
■ 2-C Bank LSB (BnkLS)
■ 2-D Program Change (Prog)
■ 3-A DSP Type (DSP)
■ 3-B DSP Parameter (Parameter)
EXT
EXT
EXT
EXT
INT
INT
INT
INT
Page: 32
English
Editing Zone Parameters
E-31
This item is used to change the setting
of the parameter displayed in 3-B.
IMPORTANT!
• For details on information about parameter names
and the settings and initial defaults for each
parameter under each DSP type number and type
name, see “DSP Effect List” (page E-60) and “DSP
Algorithm List” (page E-61).
Editing Tones
Changes the pitch in semitone steps.
–12 to 0* to +12 semitones
Use this item to adjust the pitch in cent
steps (1 cent = 1/100 semitone).
–99 to 0* to +99 cents
Specifies whether or not portamento
should be applied to each zone when
the assignable button to which portamento is assigned
is pressed.
OFF*, ON
Specifies the pitch change time when
portamento is turned on in 4-C. A
smaller number specifies a shorter time, while a larger
number specifies a longer time. Portamento is not
applied when this setting is 0.
0* to 127
Attack time is the time it takes for the
sound to reach full volume when a note
is played. This item makes relative adjustments to the
default attack time (0) of each tone. A larger positive
value lengthens the attack time, which produces a
slower attack. A larger negative absolute value
shortens the attack time, which produces a faster
attack.
–64 to 0* to +63
Release time is the time it takes for the
sound to fade when a note ends.
Adjustment is relative from the initial default setting
(0) of each tone. A larger negative absolute value
shortens the release time, while a larger positive value
lengthens the release time.
–64 to 0* to +63
This item is for adjusting how the cut-
off filter application is applied to a tone.
The cut-off filter is a tone adjustment filter that
eliminates (cuts off) all components over a given
frequency from within a tone’s overtone components.
Adjustment is relative from the initial default setting
(0) of each tone.
A larger negative absolute value produces a softer
sound, while a larger positive absolute value produces
a harder, brighter sound.
–64 to 0* to +63
This item is for adjusting how much the
sound volume and timbre changes, and how
it changes in accordance with keyboard pressure.
Setting a larger absolute value causes relatively large
change in sound volume and timbre in response to
changes in key pressure. If this setting is 0, sound
volume and timbre remain constant regardless of key
pressure.
If the setting is positive, a larger value results in harder
notes when stronger pressure is applied, and softer
notes when lighter pressure is applied. If the setting is
negative, a larger value results in softer notes when
stronger pressure is applied, and harder notes when
lighter pressure is applied. The change in sound
volume and timbre depends on the tone.
–64 to 0 to +63*
This item is for adjusting the speed of
vibrato applied to notes. A larger
negative absolute value decreases the speed, while a
larger positive value increases the speed.
–64 to 0* to +63
■ 3-C Parameter Value (Value)
■ 4-A Coarse Tune (CrsTu)
■ 4-B Fine Tune (FinTu)
■ 4-C Portamento ON/OFF (Porta)
■ 4-D Portamento Time (PTime)
■ 5-A Attack Time (Atack)
INT / EXT
INT / EXT
INT / EXT
INT / EXT
INT / EXT
INT / EXT
■ 5-B Release Time (Relas)
■ 5-C Filter Cutoff (Flter)
■ 5-D Touch Sense (Sense)
■ 6-A Vibrato Rate (VbRat)
INT / EXT
INT / EXT
INT
INT / EXT
Page: 33
E-32
Editing Zone Parameters
This item is for adjusting the depth
(strength) of vibrato applied to notes. A
larger negative absolute value makes vibrato
shallower, while a larger positive value makes it
deeper.
–64 to 0* to +63
This item is for adjusting the time until
vibrato starts to be applied to a note. A
larger negative absolute value makes the time it takes
before vibrato is applied after a note is played shorter,
while a larger positive value makes it longer.
–64 to 0* to +63
This item is for selecting the waveform when
applying vibrato to notes. You can select
from among the following waveforms.
* “Org” is the initial default setting for all tones. The
actual default waveform type depends on the tone.
Effect Settings
For details on the meanings of the settings in this
section, see the flowchart under “Master Control
Configuration” (page E-4).
Specifies how much of the signal from
the sound source is sent to reverb.
0 to 127 (*default setting depends on the tone)
Specifies how much of the signal from
the sound source is sent to chorus.
0 to 127 (*default setting depends on the tone)
Specifies how much of the signal from the
sound source is sent to acoustic resonance.
0 to 127 (*default setting depends on the tone)
Switches DSP for each zone on or off.
Selecting OFF disables DSP for that particular
zone.
OFF, ON*
The DSP of this Digital Piano can be used
simultaneously for up to two parts. Each part (“Sound
Source Configuration”, page E-5) has a DSP priority,
which determines which of the two parts that have
DSP turned on should have the DSP effect applied. The
following shows the priorities assigned to each part.
To apply a DSP to one or two lower priority parts
(Lower2, for example), turn off DSP ON/OFF for the
higher priority parts (Upper1, Lower1, Upper2).
■ 6-B Vibrato Depth (VbDpt)
■ 6-C Vibrato Delay (VbDly)
■ 6-D Vibrato Waveform (WvFrm)
Original (Org*) –– Saw Down (SDw)
Sine (Sin) Pulse 1:3 (P13)
Triangle (Tri) Pulse 2:2 (P22)
Saw Up (SUp) Pulse 3:1 (P31)
INT / EXT
INT / EXT
INT
■ 7-A Reverb Send (RvbSd)
■ 7-B Chorus Send (ChoSd)
■ 7-C Acoustic Resonance Send (AReso)
■ 7-D DSP ON/OFF (DSP)
Priority Part Number Part Name
1 Part 1 Upper1
2 Part 3 Lower1
3 Part 2 Upper2
4 Part 4 Lower2
5 Part 17 to 48
Song01 to Song16,
Ext01 to Ext16
INT / EXT
INT / EXT
INT
INT
Page: 34
English
Editing Zone Parameters
E-33
Control Settings
If you are using multiple zones for keyboard play and
you want to disable pedal and other controller
operations for a particular zone, turn off the settings
described in this section for that zone.
Enables and disables pedal operations.
OFF, ON*
Enables and disables the  (PITCH
BEND) wheel operations.
OFF, ON*
Enables and disables the 
(ASSIGNABLE 1) button operations.
OFF, ON*
Enables and disables the 
(ASSIGNABLE 2) button operations.
OFF, ON*
■ 8-A Pedal
■ 8-B Bender (Bend)
■ 8-C Assignable 1 (Asgn1)
■ 8-D Assignable 2 (Asgn2)
INT / EXT
INT / EXT
INT / EXT
INT / EXT
Page: 35
E-34
Using Registration Memory
Normally, before playing something you need to set up
the Digital Piano by configuring a number of different
settings, including layer and split on/off, a tone
selection for each zone, equalizer settings, and DSP
settings. You can save up to 64 Digital Piano setups
(which include control panel and internal settings) to
registration memory for later recall when you need
them. Each setup is saved as “registration data.”
The following are the settings that are stored as
registration data when you save a Digital Piano setup.
• Layer ON/OFF
• Split ON/OFF
• Split point
• Reverb ON/OFF
• Reverb type
• Chorus ON/OFF
• Chorus type
• Each zone tone number
• Each zone INT/EXT ON/OFF
• All common parameters (page E-18)
• All zone parameters (page E-28)
• Following function menu items (page E-38)
NOTE
• The Digital Piano’s current mode (MASTER
CONTROL, CARD PLAYER, ZONE EDIT) is not
included in registration data. This means that the
Digital Piano’s mode does not change when you
recall registration data.
• The following function menu settings are not
included in registration data. You can, however,
perform the backup operation (page E-40) to retain
these settings when the Digital Piano is turned off.
• The backup operation (page E-40) saves all of the
above function menu settings, as well as all of the
settings that are included in registration data.
During registration data save and recall operations, the
location of the data in registration memory is specified
using a bank number and an area number. Registration
memory has eight banks, each of which is divided into
eight areas.
To save a setup as registration data
1. Configure the Digital Piano with the settings
you want to save.
2. Press the  (REGISTRATION) button so the
lamp below it is lit. This is the
REGISTRATION mode.
3. Use the  (w, q) buttons to scroll through
the banks (1 to 8) until the bank where you
want to save the registration data is
displayed.
Registration Data
• Touch Response
• Pedal Assign
• Temperament type
• Temperament key note
• Stretch Tuning
• Acoustic Resonance ON/OFF
• Half Pedal Effect
• Tuning
• EQ Hold
• Display Contrast
• Song MIDI Out
• Song Volume
• Song Pre-count
• Song Repeat
Registration Memory
Operations
Bank number
Lit
MASTER CONTROL CARD PLAYER
Page: 36
English
Using Registration Memory
E-35
4. While holding down the  (STORE) button,
press one of the number buttons ( (1)
through  (8)) to specify the number of the
area (1 to 8) where you want to save the
registration data.
• Pressing a number button immediately executes the
registration data save operation.
• The following shows how the display would appear
if you select Bank 1, Area 3.
To recall a setup saved as registration
data
1. Press the  (REGISTRATION) button so the
lamp below it is lit. This is the
REGISTRATION mode.
2. Use the  (w, q) buttons to scroll through
the banks (1 to 8) until the one where the
registration data you want to recall is
displayed.
3. Press one of the number buttons ( (1)
through  (8)) to specify the number of the
area (1 to 8) where the registration data you
want to recall is located.
• Pressing a number button immediately recalls and
applies the setup in accordance with the registration
data being recalled.
• The following shows how the display would appear
if you select Bank 3, Area 7.
To rename a registration memory bank
1. While holding down the  (FUNCTION)
button, press the  (REGISTRATION)
button.
2. Use the  (w, q) buttons to scroll through
the banks (1 to 8) until the one you want to
rename is displayed.
• This displays a screen for editing the name.
3. Edit the name.
• The initial default name of all the banks is
“REGIBANKNAME”.
• Use the  (u) and  (i) buttons to move the
cursor left and right, and the  (w, q) buttons to
scroll through characters at the current cursor
position. The following shows the characters that can
be used in a name.
• You can specify up to 12 characters for a bank name.
4. After the name is the way you want, press the
 (ENTER) button.
5. In response to the confirmation message
(“Sure?”) that appears, press the  (YES)
button to apply the change or the  (NO)
button to return to the screen in step 3 of this
procedure without changing anything.
NOTE
• To display a bank name, hold down the 
(REGISTRATION) button on the registration mode
screen.
ck cl cm cn co cp cq cr dm
Area number
Bank number
9
J
T
'
8
I
S
_
`
7
H
R
&
~
6
G
Q
S
@
5
F
P
Z
}
4
E
O
Y
{
3
D
N
X
^
2
C
M
W
-
1
B
L
V
)
0
A
K
U
(
Page: 37
E-36
Using Registration Memory
Registration data can be stored to a file in the Digital
Piano’s internal memory area or on an SD card. You
can store the registration data in a single registration
memory bank (eight areas) or the data in all of the
registration memory banks (64 areas) to a file.
NOTE
• When you save registration memory bank data to a
file, a file name is assigned automatically in
accordance with the following rules.
• Before saving registration memory bank data to an
SD card, be sure to first read the important
information contained in the following sections of
this user’s guide.
To save registration memory bank data to
a file
1. Depending on where you want to save the
data file, perform one of the steps shown
below.
2. While holding down the  (FUNCTION)
button, press the  (LOAD/SAVE) button.
• This enters the LOAD/SAVE mode.
3. Depending on the type of operation you want
to perform, use the  (u) and  (i)
buttons to display one of the screens shown
below.
To save the data in a single bank
To save the data in all banks
4. Use the  (w, q) buttons to specify the
two-digit number you want to append to the
name of the file.
5. Press the  (ENTER) button.
• This saves the file.
• The message “Replace?” will appear if a file with the
same name already exists. If you want to replace the
existing file with the one you are saving, press 
(YES). Press  (NO) to return to the screen in step 4
of this procedure without saving.
6. To exit the LOAD/SAVE mode, press the 
(EXIT) button.
NOTE
• A registration memory bank data file saved to an SD
card will be placed in the MUSICDAT folder. The
MUSICDAT folder is created automatically when
you format the memory card on the Digital Piano
(page E-46). Note that load, delete, and rename
operations cannot be performed on files that are not
inside the MUSICDAT folder, or on files in folders
that are inside the MUSICDAT folder. Keep this
restriction in mind whenever handling SD card files
with your computer.
Saving Registration Memory
Bank Data to a File
• If you save the data in a single bank, the file name
will be in the format: <first 6 characters of bank
name><2-digit number specified by you>.CB6.
• If you save the data in all the banks, the file name
will be in the format: <REGIST><2-digit number
specified by you>.CR6.
• “Card and Card Slot Precautions” (page E-46)
• “To load and remove a memory card” (page E-46)
• “To format a memory card” (page E-46)
If you are saving the file
here:
Perform this operation:
Internal area Remove the SD card from the
Digital Piano’s card slot.
SD card Insert the SD card into the
Digital Piano’s card slot.
Page: 38
English
Using Registration Memory
E-37
To recall registration memory bank data
from a file
1. Depending on where the file is located,
perform one of the steps shown below.
2. Press the  (REGISTRATION) button so the
lamp below it is lit. This is the
REGISTRATION mode.
3. If you are recalling a file that contains data for
a single bank, use the  (w, q) buttons to
scroll through the bank numbers (1 through 8)
until the one to which you want to recall the
data is displayed.
• If you are recalling a file that contains data for all
banks, you can skip this step.
4. While holding down the  (FUNCTION)
button, press the  (LOAD/SAVE) button.
• This enters the LOAD/SAVE mode.
5. Depending on the type of operation you want
to perform, use the  (u) and  (i)
buttons to display one of the screens shown
below.
To recall a file that contains data for a single bank
To recall a file that contains data for all banks
6. Use the  (w, q) buttons to display the
file that contains the data you want to recall,
and then press the  (ENTER) button.
• This will cause the message “Replace?” to appear.
• To cancel the recall operation and exit the LOAD/
SAVE mode, press the  (EXIT) button.
7. To replace the registration data currently in
the bank(s) you selected with the registration
data in the file, press the  (YES) button. To
return to the screen in step 6 of this
procedure without recalling anything, press
the  (NO) button.
• Pressing the  (YES) button recalls the data from the
file into the bank(s) and exits the LOAD/SAVE
mode.
If the file is located
here:
Perform this operation:
Internal area Remove the SD card from the
Digital Piano’s card slot.
SD card Insert the SD card into the Digital
Piano’s card slot.
Page: 39
E-38
Using the Function Menu
The function menu contains global settings (overall
tuning and touch adjustment, local control ON/OFF,
etc.) that need to be changed by you relatively
infrequently. It also includes some SD card operations
(format, etc.)
This section explains operations involving function
menu settings. For details about specific function menu
items, see “Function Menu Settings” (page E-39).
To change the setting of a function menu
item
1. Press the  (FUNCTION) button.
• The button’s lamp will light, and the display will
change as shown below.
2. You can use a number button ( (1) through
 (8)) to select another item to change its
setting.
• Each number button corresponds to the numbers of
the items under “Function Menu Settings” (page
E-39).
• You also can scroll sequentially through settings with
the  (u) and  (i) buttons.
• “>ENT” to the right of an item indicates a setting
group. In this case, press the  (ENTER) button to
enter the setting group. Next, use the  (u) and 
(i) buttons to scroll through the items in the group.
• To exit a setting group, press the  (EXIT) button.
3. Use the  (w, q) buttons to change the
currently displayed setting.
• Holding down the  (FUNCTION) button as you
press w or q will change the setting by a factor of
10.
4. To exit the function menu, press the 
(EXIT) button or the  (FUNCTION) button.
IMPORTANT!
• Turning off the Digital Piano causes all function
menu settings to return to their initial defaults. If you
need to save a function menu setup, perform the
backup operation. For details, see “Backup” (page
E-40).
• Some function menu settings also can be saved to
registration memory. For details, see “Using
Registration Memory” (page E-34).
Function Menu Operations
Item name “%” indicates the setting.“>ENT”
indicates a setting group.
ENTER EXIT
MASTER CONTROL CARD PLAYER
Page: 40
English
Using the Function Menu
E-39
This section explains the meaning of each function
menu parameter, and provides information about their
setting ranges and initial default values.
• For each item, the initial default setting is indicated
by an asterisk (*).
Use this item to adjust the pitch in cent steps (1 cent =
1/100 semitone).
–99 to 0* to +99 cents
Select OFF* to overwrite existing equalizer settings
when recalling registration data (page E-34). Select ON
to retain existing equalizer settings.
Select one of the settings below to specify the
relationship between key pressure and note volume.
Specifies whether the pedal unit connected to the
SOFT/SOSTENUTO PEDAL jack is a soft pedal (SFT*)
or a sostenuto pedal (SOS).
Select OFF to disconnect the Digital Piano’s keyboard
from the internal sound source.
OFF, ON*
Function Menu Settings
1 Tuning (Tune)
2 EQ Hold
3 Touch Response (Touch)
OFF: Constant note volume regardless of keyboard pressure
1 : Strong sound even with light pressure
2* : Normal
3 : Normal sound even with strong pressure
4 Pedal Assign (PedAssign)
5 Local Control (LocalCtl.)
6 Temperament/Effect (Tmpr/Effect)
Temperament (Temper.)
Use this setting to select one of the temperaments
(tunings) shown below for the internal sound
source. Pressing a keyboard key while this item is
displayed will set that key’s note name (C* to B) as
the temperament key note.
NOTE
• Equal temperament is always used for MIDI file
playback in the CARD PLAYER mode.
Stretch Tuning (Stretch)
Stretch tuning is a standard piano tuning method
that tunes high notes slightly higher and low notes
slightly lower. Select ON* for this item to enable
stretch tuning or OFF for plain tuning.
Acoustic Resonance (AcoReson.)
Acoustic resonance occurs when the damper pedal
is depressed on a grand piano. Select ON* for this
item to enable acoustic resonance or OFF to disable
it.
Half Pedal Effect (HalfPedal)
Use this item to adjust how much a half-pedal
operation (pressing the pedal part way) when using
the damper pedal of the optional pedal unit (SP-32).
A setting of 00 disables the half pedal effect. Setting
42 applies a full-press effect, even when the pedal is
pressed part way.
00 to 24* to 42
00* : Equal
01 : Pure Major
02 : Pure Minor
03 : Pythagorean
04 : Kirnberger 3
05 : Werckmeister
06 : Mean-Tone
07 : Rast
08 : Bayati
09 : Hijaz
10 : Saba
11 : Dashti
12 : Chahargah
13 : Segah
14 : Gurjari Todi
15 : Chandrakauns
16 : Charukeshi
Page: 41
E-40
Using the Function Menu
7 Playback/Card (Play/CARD)
Song MIDI Out (MIDI Out)
Select ON* for this item to send MIDI data to an
external destination when a Format0 or Format1
SMF file is played back on the Digital Piano. Select
OFF to disable send. MIDI data is never sent during
playback of a CM2 format file, regardless of what is
selected for this setting.
Song Volume (SongVol.)
Use this item to adjust the volume level for
playback of MIDI files on the Digital Piano. This
item can be used to balance the volume level of
MIDI file playback with keyboard play volume. A
setting of 00 mutes MIDI file playback.
00 to 42*
Song Pre-count (PreCount)
Select ON for this item to sound a pre-count at the
beginning of a song when starting playback of a
MIDI file on the Digital Piano. Select OFF* to
disable the pre-count.
Song Repeat (SngRepeat)
Select ON for this item to repeat a single song when
playing back a MIDI file on the Digital Piano. Select
OFF* to disable song repeat.
Card Folder Setting (CardFolder)
See “Creating a New Card Music Folder” (page
E-44).
Card Format (CardFORMAT)
See “To format a memory card” (page E-46).
File Delete (FileDELETE)
See “To delete a file” (page E-47).
File Rename (FileRENAME)
See “To rename a file on a memory card” (page
E-47).
8 Other (General)
Panel Lock (PanelLock)
Turning on panel lock locks all of the Digital
Piano’s buttons (except for the power button and
unlock button operations*). Turn on panel lock
when you want to protect against unintentional
button operations. Turning off the Digital Piano
automatically unlocks panel lock.
* To unlock the panel, perform the same operation
you perform to turn on panel lock.
Display Contrast (Contrast)
Use this item to adjust display contrast.
00 to 08* to 16
Backup (BackUp)
Changing this item from OFF* to ON, creates a
backup data file that contains information about all
of the Digital Piano’s current settings. If this item is
left ON, the Digital Piano’s setup is configured in
accordance with the contents of the currently saved
backup data file. For details about the backup data
file contents, see the note at the end of “Registration
Data” (page E-34).
NOTE
• Changing the backup setting from ON to OFF
deletes the current backup data file. Turning the
Digital Piano off and then back on again while
the backup setting is OFF will cause all settings
to return to their initial power on defaults.
Registration memory data and internal memory
area data is not affected.
• To update the contents of the backup data file
with your current Digital Piano setup, change
the backup setting from ON to OFF and then
back to ON again.
Page: 42
E-41
English
Playing Back a MIDI File
You can use the Digital Piano to directly playback a
MIDI file stored on an SD card. You also can copy
MIDI files to the Digital Piano’s built-in memory
(internal memory area) and play it back from there.
IMPORTANT!
• Your Digital Piano supports playback of Format0 and
Format1 SMF files and CM2 (CASIO proprietary)
format file. Playback of up to 17 tracks of a Format1
SMF file is supported.
• Playback of audio files (WAV, MP3, etc.) is not
supported.
To play back a MIDI file from an SD card
1. Format the SD card on the Digital Piano
(page E-46).
• This will cause folders with the names MUSICDAT,
MUSIC__B, MUSIC__C, and MUSIC__D to be
automatically created in the SD card’s root directory.
2. Use your computer to copy the MIDI files you
want to play on the Digital Piano into the
folders that were created on the SD card in
step 1 of this procedure.
3. Insert the SD card into the Digital Piano’s
card slot.
4. Press the  (CARD PLAYER) button so the
lamp below it is lit. This is the CARD PLAYER
mode.
• The  (A) button will light, and the name of the first
MIDI file in the MUSICDAT folder will appear on the
Digital Piano’s display.
5. You can use the letter buttons ( (A) through
 (D)) to specify an SD card folder.
• A: MUSICDAT, B: MUSIC__B, C: MUSIC__C,
D: MUSIC__D.
6. Use the  (w, q) buttons to select the
MIDI file you want.
7. To start playback, press the  (PLAY/
STOP) button.
• Press the  (FF) button to perform a fast forward
operation or the  (REW) button for rewind.
Pressing and releasing either button moves one
measure, while holding down a button scrolls at high
speed.
• Pressing the  (PAUSE) button pauses playback.
Press again to resume song playback.
• For information about other operations that are
supported during playback, see “Supported
Operations During MIDI File Playback” (page E-42).
• Playback will stop when the end of the file is reached
(under initial default settings). To stop playback part
way through, press the  (PLAY/STOP) button.
8. To exit the CARD PLAYER mode, press the
 (CARD PLAYER) button.
• The lamp above the button will light, and the Digital
Piano will return to the MASTER CONTROL mode.
To play back a MIDI file from the Digital
Piano’s internal memory area
1. Copy the MIDI file you want to play to the
Digital Piano’s internal memory area.
• For information about how to copy the file, see
“Transferring Data between the Digital Piano and a
Computer” (page E-50).
2. If there is an SD card in the Digital Piano’s
card slot, remove it.
MIDI File Playback Operations
CARD PLAYER
Page: 43
E-42
Playing Back a MIDI File
3. Press the  (CARD PLAYER) button so the
lamp below it is lit. This is the CARD PLAYER
mode.
• This displays the name of the first MIDI file in the
internal memory area.
• The remaining steps of this procedure are the same as
those starting with step 6 under “To play back a MIDI
file from an SD card” (page E-41).
To change the playback tempo
There are two different methods you can use to change
the tempo setting: by pressing q (faster) and w
(slower) buttons or by tapping a beat with a button.
■ To adjust the tempo using the  (TEMPO
w, q) buttons
Each press of a button increases or decreases the beats
per minute value by one.
• Holding down either button changes the value at
high speed.
• Pressing both of the  (TEMPO w, q) buttons at
the same time will return the song to its default
tempo.
• You can specify a tempo value in the range of 20 to
255.
■ To adjust the tempo by tapping a beat
1. While holding down the  (FUNCTION)
button, tap the q  (TEMPO) button four
times in time with the beat you want to
specify.
• The tempo setting will change in accordance with the
timing of your tapping.
• After you use this method to specify the approximate
tempo, you can then use the procedure under “To
adjust the tempo using the  (TEMPO w, q)
buttons” to adjust the setting to a more exact value.
• The setting will be canceled if you release the 
(FUNCTION) button before tapping the q 
(TEMPO) button four times.
To adjust playback volume in accordance
with keyboard play volume
See “Song Volume” (page E-40). For information about
how to change the setting, see “To change the setting of
a function menu item” (page E-38).
To sound a pre-count at the start of
playback
See “Song Pre-count” (page E-40). For information
about how to change the setting, see “To change the
setting of a function menu item” (page E-38).
Supported Operations During
MIDI File Playback
Tempo value
Tap four times
Page: 44
English
Playing Back a MIDI File
E-43
To practice with either hand (Part Off)
NOTE
• To perform the procedure below, use a MIDI file that
has the left-hand part recorded in Channel 3 and the
right-hand part recorded in Channel 4.
1. Enter the CARD PLAYER mode and select
the MIDI file you want to play.
2. Press the  (PART) button.
• This will display the part on/off screen (L-[ON]
R-[ON]) to appear on the display.
3. Use the  (w, q) buttons to toggle the
parts on and off.
• w toggles the left-hand part and q toggles the
right-hand part.
4. Press the  (PART) button to exit the part
on/off screen.
5. To start playback, press the  (PLAY/STOP)
button.
• This starts playback of the part you turned on in
step 2. You can play the part you turned off on the
keyboard along with the playback.
To repeat play a specific section of a
song
1. Press the  (PLAY/STOP) button to start
song playback.
2. When playback reaches the first beat of the
section you want to select for repeat, press
the  (REPEAT) button.
• This will cause the  (REPEAT) button lamp to
flash.
3. When playback reaches the last beat of the
section, press the  (REPEAT) button again.
• The  (REPEAT) button lamp will remain lit, which
indicates that repeat playback is being performed.
After a one-measure (four beats in the cast of a 4/4
time song) rest, the Digital Piano will start playing
the section you selected. Playback of the selected
section continues, with a one-measure rest before
each playback.
• You can use the  (PLAY/STOP) button to stop and
re-start playback of the section.
4. To exit repeat playback, press the 
(REPEAT) button again so its lamp goes out.
• Using the  (w, q) buttons to switch to another
song also will exit repeat playback.
To play on the keyboard along with
playback
1. In the MASTER CONTROL mode, select the
tones you want to use for each zone you will
play on the keyboard.
• See “Selecting a Tone” (page E-11) and “Layering and
Splitting Tones” (page E-12).
2. Enter the CARD PLAYER mode and start
MIDI file playback.
• See “MIDI File Playback Operations” (page E-41).
3. Play on the keyboard along with playback.
NOTE
• The parts used for MIDI file playback (Song01
through Song16) are independent of the parts used
for Digital Piano keyboard play (Upper1, Upper2,
Lower1, Lower2). For more information, see “Sound
Source Configuration” (page E-5). This means that
playing on the keyboard does not interfere with
proper MIDI file playback.
• You can select the tones for each zone you will play
on the keyboard after entering the CARD PLAYER
mode. For more information, see “To select a tone
for each zone in the CARD PLAYER mode” (page
E-44).
Page: 45
E-44
Playing Back a MIDI File
To select a tone for each zone in the
CARD PLAYER mode
1. Press the  (LAYER) and  (SPLIT)
buttons so their lamps are lit in the
combinations shown below and select the
tones you want.
2. Press the  (TONE) button so the lamp
above it is lit.
3. Use the  to  (Tone Group) buttons to
select the group you want.
• The lamp of the button you press will light.
4. Use the  (w, q) buttons to select the
tone you want.
5. Repeat steps 1 through 4 for all of the zones
you want to use for keyboard play.
When you insert an SD card, the Digital Piano searches
for MIDI files inside of specific folders on the card.
Under initial default settings, the folders that are
searched are named “MUSICDAT” (which is assigned
to Digital Piano button  (A)), “MUSIC__B” (button
 (B)), “MUSIC__C” (button  (C)), and
“MUSIC__D” (button  (D)). Pressing a button
accesses the contents of the corresponding folder.
You can use the procedure below to assign different
folders to buttons  (B),  (C), and  (D).
• The procedure below creates a new folder and
assigns it to button  (B),  (C), or  (D). Button
assignments are stored on the SD card, so if you
remove it, the last button assignments you used will
be restored the next time you insert the card.
• If you create more than one folder for a button, the
last one you create will be assigned to the button.
• Performing the procedure below does not delete or
affect the content of the folder currently assigned to
a button.
To create a new card music folder
1. Insert the SD card into the Digital Piano’s
memory card slot.
2. Press the  (FUNCTION) button.
3. Press the  (7) button.
4. Use the  (u) and  (i) buttons to
display “CardFolder” and then press the 
(ENTER) button.
• This causes the CARD Folder screen to appear.
5. Use the  (w, q) buttons to scroll through
the button names (B, C, D) until the one for
which you want to create a new folder is
displayed within the brackets (%).
To change this
zone’s tone:
Configure the  (LAYER) and
 (SPLIT) button lamps like this:
UPPER 1 zone  (LAYER): unlit,  (SPLIT): unlit
UPPER 2 zone  (LAYER): lit,  (SPLIT): unlit
LOWER 1 zone  (LAYER): unlit,  (SPLIT): lit
LOWER 2 zone  (LAYER): lit,  (SPLIT): lit
Creating a New Card Music
Folder
Page: 46
English
Playing Back a MIDI File
E-45
6. Enter a name for the folder you want to
create.
• Use the  (u) and  (i) buttons to move the
cursor left and right, and the  (w, q) buttons to
scroll through characters at the current cursor
position. The following shows the characters that can
be used in a name.
• If you know the name of an existing folder on the SD
card, you can input the name in the above step. This
will assign the existing folder to the applicable button
without creating a new folder.
7. After the name is the way you want, press the
 (ENTER) button.
8. In response to the confirmation message
(“Sure?”) that appears, press the  (YES)
button to create the new folder or the  (NO)
button to return to the screen in step 6 of this
procedure without creating anything.
• The message “Please Wait” will remain on the
display while the operation is being performed. Do
not perform any Digital Piano operation while this
message is on the display. “Complete” appears on the
display after the operation is complete.
9
J
T
'
8
I
S
_
`
7
H
R
&
~
6
G
Q
S
@
5
F
P
Z
}
4
E
O
Y
{
3
D
N
X
^
2
C
M
W
-
1
B
L
V
)
0
A
K
U
(
Page: 47
E-46
Using a Memory Card
You can save Digital Piano registration data to a
commercially available SD memory card, if you want.
 Use a memory card with a capacity of 2GB or less.
Use of a card with a capacity that is greater than
2GB or other types of memory cards is not
supported.
 In this manual, mentions of a “memory card” refer
to an SD memory card.
■ Types of Data
Card and Card Slot Precautions
IMPORTANT!
• Be sure to observe the precautions provided in the
documentation that comes with the memory card.
• Memory cards have a write-protect switch. Use it
when you want to protect the data on the card from
accidental deletion.
• Avoid using a memory card under the following
conditions. Such conditions can corrupt data stored
on the memory card.
• Never touch the contacts of a memory card when
loading it or removing it from the Digital Piano.
• Never eject the memory card while data is being
written to or loaded from it. Doing so can corrupt the
data on the memory card and damage the memory
card slot.
• Never insert anything besides a memory card into
the card slot. Doing so creates the risk of
malfunction.
• Electrostatic charge from your fingers or the memory
card to the card slot can cause malfunction of the
Digital Piano. If this happens, turn the Digital Piano
off and then back on again.
• A memory card can become quite warm after very
long use in the memory card slot. This is normal and
does not indicate malfunction.
To load and remove a memory card
IMPORTANT!
• A memory card must be positioned correctly when
being loaded into the Digital Piano. Trying to force
an improperly oriented memory card into the slot can
damage the memory card and the slot.
1. With the top of the memory card facing
upwards (so you can see it), carefully insert it
into the Digital Piano’s memory card slot ()
until stops with a click.
2. To remove the memory card first press it into
the slot further.
This will cause the memory card to disengage and eject
partially. Pull the memory card the rest of the way out
of the slot.
To format a memory card
IMPORTANT!
• Format a memory card before using it for the first
time.
• Before formatting a memory card, make sure it does
not have any valuable data stored on it.
• The memory card format operation performed by this
Digital Piano is a “quick format”. If you want to
completely delete all of the data on the memory
card, format it on your computer or some other
device.
1. Insert the memory card you want to format
into the Digital Piano’s memory card slot.
Make sure the write-protect switch of the memory card
is not in the write-protect position so writing is enabled.
2. Press the  (FUNCTION) button.
3. Press the  (7) button.
Data Type
Description
(File Name Extension)
Supported
Operations
Save to
Memory
Card
Loadfrom
Memory
Card
Registration
(page E-34)
Digital Piano setups
(CB6, CR6)
O O
• Areas subjected to high temperature, high
humidity, or corrosive gas
• Areas subjected to strong electrostatic charge and
digital noise
Memory Card Operations
Top
MASTER CONTROL CARD PLAYER
Page: 48
English
Using a Memory Card
E-47
4. Use the  (u) and  (i) buttons to
display “CardFORMAT” and then press the
 (ENTER) button.
This will display a confirmation message (SURE?).
• If you want to cancel the format operation, press the
 (NO) or  (EXIT) button.
5. Press the  (YES) button.
• The message “Please Wait” will remain on the
display while the format operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after formatting
is complete.
• Formatting a memory card will cause folders with the
names MUSICDAT, MUSIC__B, MUSIC__C, and
MUSIC__D to be automatically created in the card’s
root directory.
To delete a file
1. Insert the SD card into the Digital Piano’s
card slot.
• This step is not necessary if you are deleting a file for
the internal memory area.
2. Press the  (FUNCTION) button.
3. Press the  (7) button.
4. Use the  (u) and  (i) buttons to
display “FileDELETE” and then press the 
(ENTER) button.
This displays a screen for selecting a file for deletion.
5. Use the  (w, q) buttons to select the file
you want to delete.
6. Press the  (ENTER) button.
This will display a confirmation message (SURE?).
• If you want to cancel the delete operation, press the
 (NO) or  (EXIT) button.
7. Press the  (YES) button.
• The message “Please Wait” will remain on the
display while the delete operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after deletion is
complete.
To rename a file on a memory card
1. Insert the SD card into the Digital Piano’s
card slot.
• This step is not necessary if you are renaming a file
for the internal memory area.
2. Press the  (FUNCTION) button.
3. Press the  (7) button.
4. Use the  (u) and  (i) buttons to
display “FileRENAME” and then press the 
(ENTER) button.
This displays a screen for changing the file name.
5. Use the  (w, q) buttons to select the file
you want to rename.
6. Use the  (u) and  (i) buttons to move
the flashing cursor to the character you want
to change, and then use the  (w, q)
buttons to change the character.
• The characters you can select are shown below.
7. After the file name is the way you want, press
the  (ENTER) button.
This will display a confirmation message (SURE?).
• If you want to cancel the renaming operation, press
the  (NO) or  (EXIT) button.
8. Press the  (YES) button.
• The message “Please Wait” will remain on the
display while the rename operation is being
performed. Do not perform any Digital Piano
operation while this message is on the display.
“Complete” appears on the display after renaming is
complete.
9
J
T
'
8
I
S
_
`
7
H
R
&
~
6
G
Q
S
@
5
F
P
Z
}
4
E
O
Y
{
3
D
N
X
^
2
C
M
W
-
1
B
L
V
)
0
A
K
U
(
Page: 49
E-48
Using a Memory Card
One of the error messages below appears on the display when a problem occurs.
• All mentions of “memory card” in the following table refer to an SD memory card.
Error Messages
Display
Message
Cause Required Action
Format 1. The current memory card format is not compatible
with this Digital Piano.
1. Format the memory card on the Digital Piano (page E-46).
2. The memory card capacity is greater than 2GB. 2. Use a memory card with a capacity of 2GB or less.
3. There is something wrong with the memory card. 3. Use a different memory card.
MediaFull 1. There is not enough room available on the memory
card.
1. Delete some of the files on the memory card to make room for
new data (page E-47), or use a different card.
2. There is not enough room available in Digital Piano
memory.
2. Delete some or all user data from Digital Piano memory to make
room for new data.
Media R/W 1. Memory card data is corrupted. 1. Use a different memory card.
2. Digital Piano memory is corrupted. 2. Backup Digital Piano memory data by copying it to your
computer, and then turn the Digital Piano off and then back on
again.
• Note that you may not be able to backup Digital Piano data in
certain cases.
No Card 1. The memory card is not loaded correctly in the Digital
Piano’s memory card slot.
1. Correctly load the memory card into the memory card slot.
2. The memory card was removed while some operation
was in progress.
2. Do not remove the memory card while any operation is in
progress.
No File 1. There is no MUSICDAT folder (page E-41) on the
memory card.
1. Create a MUSICDAT folder on the memory card or format the
memory card on the Digital Piano (page E-46).
2. There is no loadable or playable data in the
MUSICDAT folder, or there is no playable data in a
song playback folder (MUSIC__B, etc.)
2. Move the file you want to load or play into the memory card’s
MUSICDAT folder. For song playback, you can place the song
data into any one of the following folders: MUSIC__B,
MUSIC__C, or MUSIC__D.
Not SMF01 You are attempting to play back SMF Format 2 song data. This Digital Piano supports playback of SMF Format0 or Format1
only.
Protect The memory card is write-protected. Use the memory card’s write protect switch to enable writing.
ReadOnly A read-only file with the same name you are trying to use
is already stored on the memory card.
• Use a different name to save the new file.
• Remove the read-only attribute from the existing file and
overwrite it with the new file.
• Use a different memory card.
SizeOver The data on the memory card is too big to play. This Digital Piano supports playback of song data files with a
maximum size of 320 KB.
WrongDat 1. The memory card data is corrupted. —
2. The memory card contains data that is not supported
by this Digital Piano.
Page: 50
E-49
English
Connecting to a Computer
You can connect the Digital Piano to a computer and
exchange MIDI data between them. You can send play
data from the Digital Piano to music software running
on your computer, or you can send MIDI data from
your computer to the Digital Piano for playback.
The following shows the minimum computer system
requirements for sending and receiving MIDI data.
Check to make sure that your computer complies with
these requirements before connecting the Digital Piano
to it.
 Operating System
Windows® XP (SP2 or later)*1
Windows Vista® *2
Windows® 7 *3
Mac OS® X (10.3.9, 10.4.11 or later, 10.5.6 or later, 10.6.2
or later)
 USB port
IMPORTANT!
• Never connect to a computer that does not conform
to the above requirements. Doing so can cause
problems with your computer.
IMPORTANT!
• Make sure you follow the steps of the procedure
below exactly. Connecting incorrectly can make data
send and receive impossible.
1. Turn off the Digital Piano and then start up
your computer.
• Do not start up the music software on your computer
yet!
2. After starting up your computer, use a
commercially available USB cable to connect
it to the Digital Piano.
3. Turn on the Digital Piano.
• If this is the first time you are connecting the Digital
Piano to your computer, the driver software required
to send and receive data will be installed on your
computer automatically.
4. Start up your computer’s music software.
5. Configure the music software settings to
select one of the following as the MIDI device.
• For information about how to select the MIDI device,
see the user documentation that comes with the
music software you are using.
IMPORTANT!
• Be sure to turn on the Digital Piano first before
starting up your computer’s music software.
NOTE
• Once you are able to connect successfully, there is no
problem with leaving the USB cable connected when
you turn off your computer and/or Digital Piano.
• This Digital Piano conforms to General MIDI Level 1
(GM).
• For detailed specifications and connections that
apply to MIDI data send and receive by this Digital
Piano, see the latest support information provided
by the website at the following URL.
http://world.casio.com/
Minimum Computer System
Requirements
*1Windows XP Home Edition
Windows XP Professional (32-bit)
*2Windows Vista (32-bit)
*3Windows 7 (32-bit, 64-bit)
Connecting the Digital Piano
to Your Computer
CASIO USB-MIDI : (For Windows Vista, Windows 7,
Mac OS X)
USB Audio Device: (For Windows XP)
Computer USB port
A connector
B connector
Digital Piano USB port
USB cable
(A-B type)
MASTER CONTROL CARD PLAYER
Page: 51
E-50
Connecting to a Computer
You can use the procedure below to transfer
registration data from the Digital Piano to a computer
for storage. You also can transfer standard MIDI files
(SMF) from your computer to Digital Piano memory.
■ Data Types Supported for Data Transfer
IMPORTANT!
• Turning off the Digital Piano while data is being
transferred can cause all data currently stored in
Digital Piano memory to be deleted. Take care so
power is not turned off accidentally during data
transfer operations. If data is deleted, it will take
longer than normal for the Digital Piano to power up
the next time you turn it on (page E-11).
1. Remove the memory card from the Digital
Piano’s memory card slot (page E-46).
• You will not be able to transfer data between the
Digital Piano and a computer if a card is in the
memory card slot.
2. Perform steps 1 through 3 under “Connecting
the Digital Piano to Your Computer” to
connect the piano to your computer (page
E-49).
3. While holding down the  (FUNCTION)
button, press the  (USB DEVICE MODE)
button.
This will enter the storage mode, which enables data
transfer with the connected computer. The 
(FUNCTION) button lamp will flash and the display
will appear as shown below.
• To exit the storage mode at any time, press the 
(FUNCTION) button. This is the only button
operation that is supported while the Digital Piano is
in the storage mode.
• You will not be able to enter the storage mode while
any one of the following operations is in progress.
MIDI file playback, data transfer between the Digital
Piano and card
4. If your computer is running Windows XP,
double-click “My Computer”.*
Under “Devices with Removable Storage”, you should
be able to see an icon representing Digital Piano
memory or the memory card loaded in the Digital
Piano (see below).
5. Double-click “PIANO”.
You now should see the folders below.
Transferring Data between the
Digital Piano and a Computer
Data Type Description (File Name Extension)
MIDI files
(page E-41)
One of the following two types of music data
• CASIO format data (CM2)
• Standard MIDI files (MID),
SMF Format0 or Format1
Registration
(page E-34)
Digital Piano setups (CB6, CR6)
* Windows Vista, Windows 7: Double-click “Computer”.
Mac OS: Skip step 4 and double-click “PIANO” on
your Mac desktop.
PIANO drive (Digital Piano memory)
This folder is not a data folder. You should not try to use it for normal
Digital Piano operation.

Question & answers

There are no questions about the Casio Privia PX-350M yet.

Ask a question about the Casio Privia PX-350M

Have a question about the Casio Privia PX-350M but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Casio Privia PX-350M. Please make sure that you describe your difficulty with the Casio Privia PX-350M as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.