Casio KL-60 manual

View a manual of the Casio KL-60 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Casio
  • Product: Label Printer
  • Model/name: KL-60
  • Filetype: PDF
  • Available languages: English

Table of Contents

Page: 1
E-1
Batteries
• Never charge batteries, try to take batteries apart, or allow batteries
to become shorted. Never expose batteries to direct heat or dispose
of them by incineration.
Tape Cutter
• Never touch the tape cutter while a tape cut operation is being per-
formed. Doing so can result in cuts and other personal injury.
Microwave oven containers
• Never affix labels to containers used for heating food in a microwave
oven. The label material contains metal, which creates the risk of
sparking and burn injury when heated in a microwave oven. Heating
in a microwave oven can also cause deformation of the container to
which the label is affixed.
Caution
Avoid unstable areas
• Never place the unit on a wobbly table or a high shelf. Doing so can
cause it to fall, resulting in personal injury.
Water and other foreign matter
• Never allow coffee, juice, or other drinks, or flower vases to spill on
the unit. Liquid spilled on the unit creates the danger of fire and elec-
trical shock. Should liquid ever spill onto the unit, immediately turn off
power. Request servicing from your original dealer.
• Never allow metal objects or combustible materials to get into the air
vents of the unit. Doing so creates the danger of fire and electrical
shock.
Location
• Avoid leaving the unit in areas subjected to high humidity and large
amounts of dust. Such conditions create the danger of fire and elec-
trical shock.
• Avoid leaving the unit on a kitchen table, next to a humidifier, or in
any other area where it might come into contact with oil vapors or
steam. Such conditions create the danger of fire and electrical shock.
• Never place heavy objects on the unit. Doing so creates the danger
of the unit falling, resulting in personal injury.
Important Safety Precautions
Note of the following safety precautions before using the label printer for the
first time. Keep these safety precautions and operating instructions on hand for
future reference.
About safety precaution symbols
The following symbols are used in this manual and on the product itself to alert
you and others to the risk of personal and material injury.
Warning
This symbol indicates an item that can result in death or serious per-
sonal injury if ignored.
Caution
This symbol indicates an item that can result in serious personal injury
or material damage if ignored.
Examples
A circle indicates something you should not do. This symbol indicates
you should not try to take something apart.
A black circle indicates something you must do. This symbol indicates
you should unplug something.
Warning
Serious malfunction
• Continued use of the unit when smoke or a strange odor is coming
from it creates the danger of electrical shock. Immediately turn power
off. Request servicing from your original dealer.
Never try to take the unit apart
• Never try to take the unit apart or modify it in any way.Doing so creates
the danger of electrical shock, burn injury, or other personal injury.
Packaging
• Keep the plastic bag that the unit comes in out of the reach of small
children. Plastic bags create the danger of suffocation for small chil-
dren.
English
Page: 2
E-2
Batteries
• Misuse of batteries can cause them to leak acid that can cause dam-
age to nearby items and creates the possibility of personal injury.
• Be sure that the plus (+) and minus (–) sides of each battery are
facing correctly.
• Never mix batteries of different types.
• Never mix new batteries and dead batteries.
• Remove the batteries if you do not plan to use KL-60 for a long time.
• Use only the battery type specified for this label printer in this manual.
Memory
• Always keep separate written copies of any information you store in
the memory of this label printer. Data stored in memory can be unex-
pectedly lost due to malfunction, repair, dead battery, etc.
Loading and replacing batteries
• Do not touch the springs inside the battery compartment cover with
your fingers while loading or replacing batteries. The springs have
sharp areas and can cut your fingers.
Introduction
Congratulations on your selection of the CASIO KL-60 Label Printer.This CASIO
Label Printer makes it possible for you to print adhesive labels for a wide variety
of applications, such as: name tags, cassette tape labels, floppy disks, binders,
and other applications.
You can produce attractive, original labels thanks to such features as:
• Variable tape sizes (6mm, 9mm, 12mm)
• Attractive sans-serif font
• Font effects (shading, underline, box)
• Built-in symbols
• Text memory
All of this makes the CASIO label Printer the perfect tool for just about all of your
labeling needs!
Important!
• Contact a nearby dealer whenever you require servicing.
• Note that the manufacturer shall not be held liable for any loss or
claims by third parties which may arise out of the use of this product.
• Note that the manufacturer shall not be held liable for any damages
incurred as a result of data loss caused by malfunctions, repairs, or
interruption of power supply.
• It is up to the user to keep backup records of important data.
• Keep this manual on hand for future reference.
Page: 3
E-3
Contents
Important Safety Precautions .................................................... E-1
Part 1 Getting Acquainted ......................................................... E-4
Important Precautions ................................................................................. E-4
General Guide ............................................................................................. E-4
Label Printer Menus .................................................................................... E-4
Part 2 Getting Ready .................................................................. E-5
Power Supply .............................................................................................. E-5
Replacing Batteries ..................................................................................... E-5
To load the batteries ........................................................................... E-5
Turning Power On and Off .......................................................................... E-6
Resetting the Memory ................................................................................. E-6
To reset the memory ........................................................................... E-6
Auto Power Off Function ............................................................................. E-6
Tape Cartridges ........................................................................................... E-6
To load a tape cartridge ...................................................................... E-6
Tape Width Specification ............................................................................. E-7
To specify 6mm tape width ................................................................. E-7
Part 3 Inputting Characters and Symbols ................................ E-7
Display Symbols and Indicators .................................................................. E-7
Basic Alpha-Numeric Input .......................................................................... E-8
To input alpha-numeric characters ...................................................... E-8
About the CODE key… ............................................................................... E-9
Special Symbols ......................................................................................... E-9
To input special symbols ..................................................................... E-9
Part 4 Deleting and Inserting Characters ................................. E-9
Moving the Cursor ....................................................................................... E-9
To move the cursor ............................................................................. E-9
Deleting Individual Characters .................................................................... E-9
To delete characters using the BS key ............................................... E-9
To delete characters using the DEL key ........................................... E-10
Clearing the Display .................................................................................. E-10
To clear the display ........................................................................... E-10
Text Editing ............................................................................................... E-10
To insert new characters ................................................................... E-10
To change existing characters to different ones................................ E-10
Part 5 Character Size and Text Effects ................................... E-10
Character Size .......................................................................................... E-10
To change the character size ............................................................ E-11
Text Effects ............................................................................................... E-11
To specify a text effect ...................................................................... E-11
Part 6 Printing ........................................................................... E-12
Printing a Tape .......................................................................................... E-12
To print a tape ................................................................................... E-12
Mirror Image Printing ................................................................................ E-12
To turn mirror image printing on and off ............................................ E-12
Other Printing Features and Operations ................................................... E-12
Print Density .............................................................................................. E-12
To adjust the print density ................................................................. E-13
Manual Feed ............................................................................................. E-13
To manually feed tape ....................................................................... E-13
Part 7 Memory .......................................................................... E-13
To store text into memory ................................................................. E-13
To recall text from memory ............................................................... E-13
Part 8 Reference ....................................................................... E-14
Cleaning the Printer Head and Roller ....................................................... E-14
To clean the printer head and roller .................................................. E-14
Initial Power On Settings ........................................................................... E-14
Initializing the Label Printer ....................................................................... E-14
To initialize the Label Printer ............................................................. E-14
Troubleshooting ........................................................................................ E-15
Error Messages ......................................................................................... E-16
Alpha Characters ...................................................................................... E-17
Symbols .................................................................................................... E-17
Specifications ............................................................................................ E-18
Page: 4
E-4
Part 1 Getting Acquainted
This part of the manual provides you with important information you need to
know in order to use the Label Printer to its full potential. Be sure to read it
carefully before using the Label Printer for the first time.
Important Precautions
• Keep your Label Printer out of areas subject to temperature extremes, mois-
ture and direct sunlight.The recommended temperature range is 10° to 35°C
(50° to 95°F).
• Don’t let coffee, juice or other liquids splash onto the Label Printer.
• Never let paper clips, pins or other foreign objects get into the tape outlet slot
or printer of the Label Printer.
• Do not pile heavy objects on top of the Label Printer.
• Never try to take the Label Printer apart or attempt your own maintenance.
• Do not drop your Label Printer and avoid strong impact.
• Do not pull on the tape or try to force it back into the Label Printer.
• Do not use benzine, thinner, or other volatile chemicals to clean the exterior
of the Label Printer. Use a soft, dry cloth or a cloth dampened in a weak
solution of a mild, neutral detergent and water. Wring the cloth out until all
excess moisture is removed.
• A dirty printer head can cause printing to become smudged. When this hap-
pens, clean off the printer head by wiping it with a cotton swab moistened
with alcohol (page E-14).
• Use of the Label Printer next to a television or radio may interfere with recep-
tion.
General Guide
Label Printer Menus
Label Printer operation is designed to be as simple as possible, thanks to on-
screen menus that you can use to select the settings you need. Each menu is
described in detail in the sections that follow in this manual, but note the follow-
ing general points when using them.
• The item that is underlined in a menu is the one that is currently selected.
.: ;
,
• Use H and J to move the underlining left and right and change the selected
item.
• Press SET to execute the underlined item, or ESC to exit the displayed menu
(and return to the previous menu or screen) without selecting anything.
• When you press SET to execute a menu item, the Label Printer either moves
on to the next menu, or it executes the selected function and returns to the
text input screen that you started from.
5
1
2
3
4
6
1 Power ON/OFF Key
Turn power on and off.
2 Function key
3 Letter keys
4 Tape cutter button
5 Liquid crystal display (LCD)
6 Tape outlet
Currently selected item
Page: 5
E-5
Part 2 Getting Ready
This part of the manual tells you how to load batteries and the tape cartridge,
and how to perform other basic setups for the Label Printer.
Important!
• Be sure to read this section before attempting to use the Label Printer.
Power Supply
The Label Printer can be powered by six AA-size alkaline batteries.
Replacing Batteries
A handy low battery power indicator lets you know when battery power is get-
ting too low for proper operation. The message “BATT” appears on the display
if battery power is low when you perform any of the following operations.
• Turn power on
• Execute a print operation
Whenever the “BATT” message appears, press SET to clear it from the display.
You should still be able to perform some Label Printer operations, but some
power intensive operations (like printing) may become impossible if battery power
is too low. In any case, you should replace batteries as soon as possible after
the “BATT” message appears.
Important!
• All data stored in memory is deleted whenever batteries go dead and when
you replace batteries. Be sure to keep written backup copies of all important
data (text and documents).
• Batteries can burst or leak and damage your unit if you do not use them
correctly. Note the following important points.
• Be sure that the plus (+) and minus (–) sides of each battery are facing cor-
rectly.
• Never mix batteries of different types
• Never leave dead batteries in the Label Printer.
• Remove the batteries if you do not plan to use the Label Printer for a long
time.
• Replace the batteries in accordance with the battery life marked on the side
of the battery.
Warning!
• Never use recharged batteries with the unit.
• Do not expose batteries to direct heat, do not short circuit them, and do not
try to take them apart.
• Keep batteries out of the reach of small children. If swallowed, consult
with a physician immediately.
• Be sure to replace the batteries in accordance with the battery life printed on
the side of the battery itself.
To load the batteries
Caution
• Do not touch the springs inside the battery
compartment cover with your fingers while
loading or replacing batteries. The springs
have sharp areas and can cut your fingers.
1. Turn power off.
2. Turn over the label printer. While pressing
down on the back cover lock remove the
back cover as shown in the illustration.
3. Load batteries into the battery compartment.
• Be sure to use alkaline batteries.
• Make sure the positive (+) and negative (–)
ends of the batteries are facing correctly when
you load them.
4. Replace the back cover.
• Make sure the back cover is positioned as
shown in the illustration when replacing it.
Trying to force the cover into place while it is
in the wrong position can cause damage to
the cover or label printer.
• Make sure that the tape cartridge is securely
in place and that the back cover is closed se-
curely before using the label printer. A loose
tape cartridge can cause print quality problems.
Page: 6
E-6
Turning Power On and Off
Press ON/OFF to turn power on and off.
Important!
• If you are using the Label Printer for the first time, you should reset it first.
Resetting the Memory
You should reset the memory of the Label Printer before using it for the first
time, after you have not used it for a long time, or if nothing happens when you
turn power on, even after you change the batteries.
Important!
• Resetting Label Printer memory clears its memory of all input data.
To reset the memory
1. Make sure that Label Printer power is off.
2. While holding down the PRINT and ESC keys,
press ON/OFF to turn power on.
3. Keeping PRINT and ESC held down, release
the ON/OFF key only.
4. Release PRINT and ESC keys.
5. Press SET to initialize the Label Printer or ESC to abort the reset operation
without initializing anything.
• See “Initializing the Label Printer” on page E-14 for information on the initial
default settings of the Label Printer following the reset operation.
Auto Power Off Function
If you do not perform any key operation for about six minutes, the Label Printer
automatically turns power off. To restore power, press ON/OFF.
Tape Cartridges
Use the procedures described below to load a tape cartridge into the Label
Printer. After you load the tape cartridge, be sure to use the procedure de-
scribed under “Tape Width Specification” on page E-7 to tell the Label Printer
what is the width of the tape you are using.
Important!
• Never try to push the tape back into the cassette. Once tape is out of the
cassette, there is no way to wind it back in. Trying to do so can cause opera-
tional problems with the Label Printer.
• The following are the tape widths that can be used with this printer: 6mm,
9mm, 12mm.
To load a tape cartridge
1. Make sure that the Label Printer is turned off.
2. Open the back cover while pressing down on
its look.
3. Remove the stopper from a new tape cartridge
and check to see that the tape is ready to use.
• Make sure that the tape is under the tape guide
and that it is not bent or twisted.
• Make sure that the tape does not extend too far
past the tape guide. If it does, cut off the end
with a pair of scissors.
INT?
OK!
Tape guide
NO!
Page: 7
E-7
4. Use a pencil or some other thin object to take
up slack in the ink ribbon as shown in the illus-
tration. Note that the tape does not move at this
time.
• If the ink ribbon is slack when you load it into the
Label Printer, it can break or cause some other
problem.
• Be sure to turn the ink ribbon take up spool only
in the direction indicated by the arrow (a).
• Turn the spool until the other spool (b) starts turn-
ing in the direction noted by the arrow. This indi-
cates there is no slack in the ribbon.
5. Slide the printer head release in the direction
indicated by the arrow.
• If there is a cartridge already in the Label Printer,
remove it by grasping the cartridge on both sides
with your thumb and forefinger, and lift straight up.
6. Load the tape cartridge into the Label Printer,
making sure that the tape and ink ribbon pass
between the head and roller.
7. Return the printer head release to its original position by sliding in the direction
opposite to that indicated by the arrow in the illustration in step 5.
8. Close the back cover.
9. Turn on Label Printer power and press FUNC and then PRINT (FEED) two or
three times to make sure that the tape comes out without any problem.
• If the tape does not come out normally, turn off power and start again from
step 1 above.
Tape Width Specification
Important!
• When using 6mm tape, using certain character sizes can cause characters to
run off the top or bottom of the tape. Be sure to use the following procedure to
tell the Label Printer when you are using 6mm tape.
(a)
To specify 6mm tape width
1. Turn power on.
2. Press FUNC and then EFFECT (6mm).
3. Press H and J to change the setting shown on the display between ON
(6mm tape) and OFF (other tape width).
4. When the tape width setting is the way you want it, press SET to register it.
• The tape width you set remains in effect until you change it, press ON/OFF or
reset the Label Printer’s memory.
Part 3 Inputting Characters and Symbols
This part of the manual tells you how to input characters.To make things easier
to understand, we call everything you input a character, regardless of whether it
is actually a letter, number, or symbol. Explanations here all use the default
settings that are in effect from the initial power-on screen.
For information on using other character effects and sizes, see page E-10.
Important!
• You can input up to 63 characters per label. Further input becomes impossi-
ble after you input the 63rd character.
Display Symbols and Indicators
Before getting into actual input, you should first become acquainted with the
symbols and indicators used on the Label Printer display.
Roller
Head
(b)
A
KL-60
CAS
A
CAPS
MIRROR
6mm
TAPE:6~12mm
A
FUNCTION
SHIFT
CODE
Shift
indicator
Mirror image
printing
indicator
Cursor
Caps indicator
Effect indicators
Function indicator
Code
indicator
Character position marks
6mm tape indicator
Page: 8
E-8
• Function indicator
This indicator appears when you press the FUNC key. Pressing a key while this
indicator is on the display causes the function marked above that key to be
executed.
• Shift indicator
This indicator appears when you press the SHIFT key.While this indicator is on
the display, the keyboard is shifted, so the letter keys input upper-case alpha
characters. The number keys input the punctuation symbols marked in the up-
per right corners of the keys.
If both the caps mode indicator and the shift indicator are shown on the display,
the keyboard is shifted to lower-case input.
The keyboard automatically unshifts (and the shift indicator disappears) as soon
as you input a character.
• Code indicator
This indicator appears when you press the CODE key.While this indicator is on
the display, number keys 1 through 0 input the accents marked above them and
the U, O, P, A, S, J, K, L, Z, C and N keys input the special characters marked
in their lower right corners.
The keyboard automatically returns to normal (and the code indicator disap-
pears) as soon as you input an accent.
• Caps indicator
This indicator appears when the Label Printer is in the caps (upper-case) mode.
All letters you input in the caps mode are upper-case. When the caps mode
indicator is not shown on the display, all letters are input as lower-case.
Note that the Label Printer stays in the caps mode until you press the CAPS
key again.
If both the caps mode indicator and the shift indicator are shown on the display,
the keyboard is shifted to lower-case input.
• Effect indicators
These indicators point to the character effect that is currently in use. You can
select between shading, underline, and box.
• Mirror image printing indicator
This indicator appears when the Label Printer is set up for mirror image printing.
Normal (non mirror image) printing is performed when this indicator is not shown.
• 6mm tape indicator
This indicator appears when you use the procedure on page E-7 to specify you
are using 6mm tape. No indicator is shown when you are using other (9mm,
12mm) tape.
• Cursor
The cursor shows the next input position. Any character you input appears at
the point where the cursor is located.
• Character position marks
These marks show where characters will appear as you input them.This part of
the display is always blank when you turn power on.
Basic Alpha-Numeric Input
The following operation shows you the basic procedures for inputting letters
and numbers. We will explain the procedure by inputting the following charac-
ters using the default initial power-on screen.
Note
• If you hold down any key, it will repeat its operation or input at high speed until
you release it.
To input alpha-numeric characters
1. Turn power on.
2. Input the first line of characters.
• To input the upper-case letters, you can use either SHIFT or CAPS. With
SHIFT you must shift the keyboard for each character. With CAPS the key-
board stays in upper-case until you press CAPS again.
• Press SPACE to input spaces.
• If you input a wrong character, press BS to delete it and input again. See
page E-9 for other details on editing text.
3. When you reach the end of a line of text, press B (the SET key) to input a
newline mark.
• A newline operation is indicated on the display by the B symbol.This shows
where you changed lines.
• You cannot input a newline mark when using 6mm tape.
4. Input the characters in the second line.
5. To print the text that you input, press PRINT. For details on printing, see
page E-12.
Page: 9
E-9
About the CODE key…
The CODE key makes it possible to input punctuation needed for a number of
different languages. The following shows the key operations you should use for
each of the characters formed using the CODE key.
* Lower case only.
Example: To input á.
CODE 1 A
Special Symbols
You can also access a menu of special symbols by pressing SYMBOL.
To input special symbols
Example: To input the special symbol #.
1. With the cursor at the location where you want
to input a special symbol, press SYMBOL.
• The symbol that is underlined on the display is
the one that is currently selected.
2. Use the H and J cursor keys to move the underlining to the symbol you
want.
• Not all of the available symbols fit on the display. The menu will scroll when
you press the cursor keys.
• In this example, underline #.
3. After you underline the symbol you want, press
SET.
• This returns to the input screen, with the symbol
you selected input at the location where the cur-
sor was located when you displayed the symbol
list.
Part 4 Deleting and Inserting Characters
This section describes everything you need to know about deleting and editing
characters you have already input.
Moving the Cursor
Use the cursor keys to move the cursor around the display and position it for
deleting and editing characters.
To move the cursor
• Press H to move the cursor to the left, and J to move the cursor to the right.
• Press FUNC and then H to make the cursor jump to the beginning (far left) of
the characters on the display.
• Press FUNC and then J to make the cursor jump to the end (far right) of the
characters on the display.
• Holding down the H or J cursor key moves the cursor at high speed.
Deleting Individual Characters
You can delete individual characters with either the BS key or the DEL key.The
only difference between the operation of these two keys is the location of the
cursor.
To delete characters using the BS key
Example: To change the word “commmputer” to “computer”.
1. Use H and J to move the cursor under “p”.
2. Press BS twice to delete the two m’s to the left of the cursor, shifting “puter”
to the left as you do.
3. Press FUNC and then J to jump back to the end of the characters for more
input.
.: ;
,
Key Operation Input Key Operation Input Key Operation Input
CODE U Ü
CODE O Œ
CODE P Å
CODE A Æ
CODE S* ß
CODE J Ö
CODE K Ä
CODE L J
CODE Z W
CODE C Ç
CODE N Ñ
CODE 1 ´
CODE 2 `
CODE 3 ¨
CODE 4 ˜
CODE 5 ˆ
CODE 6 ˇ
CODE 7 °
CODE 8 /
CODE 9 ˝
CODE 0 ˛
IO#
pute
Page: 10
E-10
To delete characters using the DEL key
Example: To change the word “commmputer” to “computer”.
1. Use H and J to move the cursor under the first (far left) “m”.
2. Press DEL twice to delete the two m’s at the cursor’s position, shifting “mputer”
to the left as you do.
3. Press FUNC and then J to jump back to the end of the characters for more
input.
Clearing the Display
Use the following procedure to clear all input text from the display.
To clear the display
Press FUNC and then DEL (CLS).
At this time the message CLS? appears on the display to confirm that you want
to clear the display. Press SET to clear or ESC to abort the operation without
clearing anything.
Text Editing
You can use the following procedures to edit text on the display.
To insert new characters
Example: To change the text “ABCDEF” to “ABCXYZDEF”.
1. With the original text on the display, move the cursor under the letter “D”.
2. Input the new characters (XYZ).
• Inputting the new characters causes them to be inserted at the cursor posi-
tion. The existing characters are opened up to make room for the new char-
acters.
To change existing characters to different ones
Example: To change the text “ABCDEF” to “XYZDEF”.
1. With the original text on the display, use either the BS key or DEL key to
delete the characters to be changed (ABC).
• Remember to use the correct cursor location for the key you plan to use to
delete the characters. See page E-9 for details.
2. Input the new characters (XYZ).
Part 5 Character Size and Text Effects
This part of the manual explains how to change the size of characters. It also
tells you how to assign text effects like underlining, shading, and box printing.
Character Size
The following table shows the six character sizes that are available.
*These sizes are not supported when using 6mm tape.
They are automatically converted as shown below.
2 × 1 → 1 × 1
2 × 2 → 1 × 2
2 × 3 → 1 × 3
Character size changes are applied to printed text only. The size of the dis-
played text does not change.
Important!
• Any character size specification you make is applied to all the characters on
the display. You cannot make multiple specifications for specific characters.
• The Label Printer automatically adjusts the character size whenever you in-
put a B symbol to create a 2-line label as shown below.
Deleting the B symbol with a backspace or delete operation reverts to the
initial (unadjusted) character size.
Character Size Indicator Actual Size (mm)
1×1 2.5×2.5
1×2 2.5×5
1×3 2.5×7.5
2×1* 5×2.5
2×2* 5×5
2×3* 5×7.5
Initial Size Size After B
B
B
B
B Operation
AUTO 1×1
2×1 1×1
2×2 1×2
2×3 1×3
Page: 11
E-11
Text Effects
There are three text effects that you can assign: shading, underlining, and boxed
text. The following shows examples of each.
Shading:
Underlining:
Boxed Text:
Text effect changes are applied to printed text only. The appearance of the
displayed text does not change, but the text effect indicators will show you when
a text effect is being used.
Important!
• Any text effect specification you make is applied to all the characters on the
display. You cannot make multiple specifications for specific characters.
• Underlining and boxed text may overlap with some characters.
• Due to overlapping of the two effects, underlining is not visible if you use it in
the same line as boxed text.
To specify a text effect
1. Input the text.
2. Press EFFECT to display a menu of text effects.
—
3. Use H and J to move the cursor to the effect you want to use.
4. When the cursor is located under the effect you
want to specify, press SET to select it and re-
turn to the text display.
Note
• You could also perform the above procedure in reverse, specifying the text
effect first and then inputting the text.
Note that you cannot input a B symbol if you are using 6mm wide tape.
• The Label Printer automatically adjusts the character size whenever you de-
lete a B symbol to change a two-line label to a 1-line label.
To change the character size
Example: To input “ABXYZ” as 2×2 characters.
1. Input the text.
2. Press SIZE to display the current character size
setting.
3. Use H and J to change the displayed size in the following sequence.
1×1 1×2 1×3 2×1 2×2 2×3
2×3 2×2 2×1 1×3 1×2 1×1
AUTO
AUTO
4. When the character size you want to specify is
on the display, press SET to select it and return
to the text display.
Note
• You could also perform the above procedure in reverse, specifying the char-
acter size first and then inputting the text.
AUTO
Initial Size Size After Delete of B
B
B
B
B
AUTO 2×2
XYZ
Box
Underline
Normal (no effects)
Shading
Cursor
XYZ
Page: 12
E-12
• An easy way to remove the backing from a tape
and expose the adhesive surface is to bend the
tape near one of its ends. This should cause the
tape and its backing to separate, allowing you to
pull them apart.
Mirror Image Printing
When you specify mirror image for text, it is printed in reverse image. Use mir-
ror image when you plan to print on transparent tape, with the printing on the
inside. When viewed through the transparent tape, the text will appear normal.
Normal
Mirror Image
To turn mirror image printing on and off
1. Press FUNC and then MEMO (MIRROR).
2. Press H and J to change the setting shown on the display between ON
(mirror printing) and OFF (normal).
3. When the mirror image printing setting is the way you want it, press SET to
register it.
• A mark appears next to the MIRROR indicator on the display when mirror
printing is turned on.
• After you turn printing on, input text and perform the print operation as you
normally do to produce mirror image tapes.
Other Printing Features and Operations
The following are other operations and settings that you may need to use when
printing.
Print Density
The print density setting controls how darkly figures are printed on your tapes.
Part 6 Printing
This part of the manual includes all the information you need to print tapes.
Printing Precautions
• Never turn power off while printing is being performed.
• Make sure that the tape outlet is not blocked before you start printing.
• Never operate the tape cutter while printing is being performed (indicated by
the message “PRNT” on the display).
• During printing at very high density, printing of very long text, or repeat print-
ing of the same text a number of times, the Label Printer may stop printing for
about five seconds. This is not a malfunction, and normal printing should
resume shortly (indicated by the message “P R N T” on the display).
• Maximum printing width is 5mm.
Important!
• Never touch the tape cutter while a tape cut operation is being performed.
Doing so can result in cuts and other personal injury.
Printing a Tape
Printing a tape is as easy as pressing the PRINT key.
To print a tape
1. Press the PRINT key to print a tape of the text you have input and laid out.
• To stop a print operation that is in progress, press ESC.
2. After the print operation is complete, press down on the tape cutter button to
cut the tape.
• Do not use excessive force when pressing the cutter button. Doing so can
damage the button or the cutter.
3. Use scissors to trim the tape to the size you want, if necessary.
• After you print a tape, you can peel off its paper
backing and stick the tape onto the object you
want. Note that the tape will not stick on coarse,
wet, oily, or soiled surfaces. Also, you should not
try to use the tape where it is exposed to direct
sunlight or rain. Do not stick the tape onto hu-
man skin.
Tape
Backing
OFF
Page: 13
E-13
4. Press SET to store the text in memory or ESC to abort the store procedure
without storing anything.
• You can have only one block of text stored in memory.
• If you perform the data store operation while there is already a block of text in
memory, the message “OVR?” (“OK to overwrite the existing text?”) appears
when you press SET in step 4. When this happens, press SET again to replace
the existing data with the new data, or ESC to abort the store procedure
without storing anything.
To recall text from memory
1. While the input screen is on the display, press MEMO.
• Note that text recalled from memory will replace any text currently on the
display.
2. Press H or J a number of times to change to
the text recall prompt.
3. Press SET.
• If all of the text does not fit on the display, you can use H and J to scroll it to
the left and right.
4. Press SET to recall the text from the area that is currently on the display.
• Note that recalling text from memory replaces anything that is currently on
the input display. Memory text cannot be appended.
.
To adjust the print density
1. Press FUNC and then SIZE (DENSITY).
2. Use H and J to move the underlining to the density setting that you want.
• The lightest setting is 1, while the darkest setting is 5.The standard setting is 3.
• Only four of the five settings that are available can appear on the display. The
display scrolls left and right when necessary to show all of the available settings.
3. When the density setting is the way you want it, press SET to register it.
Manual Feed
To manually feed tape
Press FUNC and then PRINT (FEED) to feed the tape 19mm.
Part 7 Memory
This part of the manual tells you how to store text in memory for instant recall
when you need it.You can have one block of text (containing up 63 characters)
stored in memory.
Important!
• Text stored in memory is deleted whenever batteries go dead and when you
replace batteries. Be sure to keep written backup copies of all important text.
To store text into memory
1. Input the text you want to store.
2. Press MEMO.
3. Press H or J a number of times to change to
the text store prompt.
1234
STR?
CAL?
Page: 14
E-14
Initial Power On Settings
The following are the initial settings of the Label Printer whenever you turn it
power on.
Initializing the Label Printer
If you experience serious malfunction of the Label Printer or if operation fails
completely, try performing the following operation to initialize the printer.
Important!
• Initializing the Label Printer deletes all memory contents. Make sure you have
a back-up copy of text stored in memory if you need it.
To initialize the Label Printer
1. Turn power off.
2. While holding down the PRINT and ESC keys,
press ON/OFF to turn power on.
3. Keeping PRINT and ESC held down, release
the ON/OFF key only.
4. Release PRINT and ESC keys.
• This prompt confirms whether or not you want to
initialize the Label Printer.
5. Press SET to initialize the Label Printer or ESC to abort the reset operation.
• The following table shows the initial settings.
Part 8 Reference
This section contains information about the Label Printer that you can use as
reference when you need it.
Cleaning the Printer Head and Roller
A dirty printer head and roller can result in poor printing quality. If you have
problems with print quality, use the following procedure to clean the printer head
and roller.
To clean the printer head and roller
1. Make sure the Label Printer is turned off.
2. Turn over the Label Printer, and open the back cover while pressing down
on its lock.
3. Slide the printer head release in the direction
indicated by the arrow, and remove the tape
cartridge.
4. Use a cotton swab dipped in alcohol to clean the printer head and roller as
shown in the illustration.
5. Replace the tape cartridge and close the back cover.
Item Power On
Display Cleared
SIZE AUTO (2×2)
EFFECT CANCEL
MIRROR OFF
6mm OFF
Printer head
Roller
INT?
Item
Display
Memory
SYMBOL
SIZE
EFFECT
MIRROR
MEMO
DENSITY
6mm
Reset
Cleared
Cleared
,
AUTO (2×2)
CANCEL
OFF
STR?
3
OFF
Page: 15
E-15
Troubleshooting
• Power Supply
• Text Input
Nothing appears on the display.
Possible Cause Action
Low batteries
Batteries loaded
incorrectly
Replace batteries.
Remove batteries and reload them correctly.
Cannot input text.
Possible Cause Action
FUNC key has been
pressed.
Press ESC to clear FUNC key operation.
Back cover is not closed
completely.
No more tape left in the
cartridge.
Tape jam
Securely close the back cover.
Replace the tape cartridge with a new one.
Remove the tape cartridge and pull out the
jammed tape by hand. Cut off excess tape
with scissors, and carefully replace the
cartridge into the label printer.
Important!
Never allow the tape outlet to become
blocked and never touch tape as it is being
fed during printing.
Tape comes out when PRINT is pressed, but nothing is printed on it.
Possible Cause Action
Only blank spaces were
input.
Input the text you want to print.
Tape does not come out when PRINT is pressed.
Possible Causes Action
Printing is blurred, blotched, broken, etc.
Possible Causes Action
Improper print density
setting
Improper loading of the
cartridge
Dirty print head or rubber
roller
Adjust the print density setting.
Remove the tape cartridge and reload it
correctly.
Clean the printer head and roller.
Remove the tape cartridge and check to
make sure the ink ribbon is not broken. Next,
take up any slack in the ink ribbon and then
reload the tape cartridge.
Important!
• Before loading a tape cartridge into the
label printer, always make sure you take
up any slack in the ink ribbon first.
• If the ink ribbon is broken, you must
change to another tape cartridge.
Tape cartridge loaded
while the ink ribbon is
slack.
Ink ribbon is being fed from the tape outlet along with the tape.
Possible Cause Action
Page: 16
E-16
• Tape Cutting
• Using Labels
Cannot cut tape.
Possible Cause Action
Tape cutter blade is dull. Take the label printer to the dealer from whom
you purchased it to have the tape cutter blade
replaced.
Printed text is cut off by tape cut operation.
Possible Causes Action
Out of tape Replace the tape cartridge with a new one.
Label will not adhere to a surface.
Possible Causes Action
Peel the backing paper from the back of the
tape to expose the adhesive.
Labels do not adhere well to surfaces that are
rough, wet, oily, or dirty.
The backing paper is still
on the back of the tape.
Surface is unsuitable for
affixing a tape.
Error Messages
Message
BATT
ERR!
* This message
appears on the
screen for about
one second.
ERR!
Perr
(Printer Error)
Possible Causes
• Battery power is too low.
• Attempt to input two B
marks within the same
text.
• Attempt to input B mark
while 6mm is specified as
the tape width.
• Label text containing a
B mark was input and
then tape width specifica-
tion was changed to
6mm. (ERR! message
appears when you try to
perform a print operation.)
• Attempt to recall call text
from memory when
memory is empty.
• Attempt to store text into
memory when there is no
text on the input display.
• Memory data has become
corrupted for some
reason.
• Tape jam during printing.
Action
• Replace batteries.
• Use only one B mark.
Only two lines of text can
be input, so text can
contain only one B
mark.
• Do not use B marks.
6mm tape can have only
one line of text, so text
cannot contain any B
marks.
• Delete the B mark to
print on 6mm tape or
switch back to a wider
tape.
• Initialize the Label
Printer.
• Turn off power, remove
the tape cartridge, and
clear the tape jam. If the
printer error message
reappears after you clear
the tape jam, request
servicing from your
original dealer.
Page: 17
E-17
Alpha Characters Symbols
Page: 18
E-18
Specifications
Model: KL-60
Input
Keyboard Layout: Typewriter (QWERTY)
Character Types
Alpha (English and other languages): 151
Numbers: 10
Symbols: 46
Display
Type: Liquid crystal display
Columns: 4
Character matrix: 5×7-dot
Printing
Type: Thermal transfer
Width: 5mm
Character Matrix: 16×16-dot
Character font: Sans-serif
Character effects: Shade, underline, box
Character sizes: 1×1, 1×2, 1×3 (6mm tape);
1×1, 1×2, 1×3, 2×1, 2×2, 2×3 (other tapes)
Number of lines: 1 (6mm tape); 1 or 2 (other tapes)
Memory
Text: One block (up to 63 characters)
General
Power supply: Six AA-size alkaline batteries
Battery life: Approximately 10 tape cartridges (normal characters printing at
nomal temperature)
Power consumption: 9W
Auto Power Off: Approximately six minutes after last key operation.
Dimensions: 49 (H) × 168 (W) × 114 (D)mm (1 15/16"H × 6 5/8"W × 4 1/2"D)
Weight: 300g (excluding batteries)
Ambient Temperature: 10°C~35°C (50°F~95°F)
Page: 19
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
MO0105-A Printed in China/Imprimé en Chine
A344043-1

Question & answers

There are no questions about the Casio KL-60 yet.

Ask a question about the Casio KL-60

Have a question about the Casio KL-60 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Casio KL-60. Please make sure that you describe your difficulty with the Casio KL-60 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.