Bosch PST 800 PEL manual

View a manual of the Bosch PST 800 PEL below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Bosch
  • Product: Saw
  • Model/name: PST 800 PEL
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Swedish, Portuguese, Danish, Norwegian, Finnish, Turkish

Table of Contents

Page: 0
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-pt.com
2 609 003 951 (2009.10) T / 128 WEU
0
˚
4
5
˚
4
5
˚
0
˚
4
5
˚
4
5
˚
PST 800 PEL
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
Page: 1
2 609 003 951 | (6.10.09) Bosch Power Tools
2 |
0
˚
4
5
˚
4
5
˚
0
˚
4
5
˚
4
5
˚
1 2 3
12
4
5
6
7
8
9
10
11
15
13
15
13
14
PST 800 PEL
2
1
A
Page: 15
16 | English
2 609 003 951 | (6.10.09) Bosch Power Tools
en
Safety Notes
General Power Tool Safety Warnings
Read all safety warnings and all
instructions. Failure to follow
the warnings and instructions may result in elec-
tric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radia-
tors, ranges and refrigerators. There is
an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges and moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for out-
door use reduces the risk of electric shock.
f) If operating a power tool in a damp loca-
tion is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment
of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or bat-
tery pack, picking up or carrying the tool.
Carrying power tools with your finger on
the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench be-
fore turning the power tool on. A wrench
or a key left attached to a rotating part
of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unex-
pected situations.
f) Dress properly. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the connec-
tion of dust extraction and collection fa-
cilities, ensure these are connected and
properly used. Use of dust collection can
reduce dust-related hazards.
WARNING
Page: 16
English | 17
Bosch Power Tools 2 609 003 951 | (6.10.09)
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better
and safer at the rate for which it was de-
signed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp
cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations differ-
ent from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a qual-
ified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
Safety Warnings for Jigsaws
f Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed
metal parts of the power tool “live” and
could give the operator an electric shock.
f Keep hands away from the sawing range.
Do not reach under the workpiece. Contact
with the saw blade can lead to injuries.
f Apply the machine to the workpiece only
when switched on. Otherwise there is dan-
ger of kickback when the cutting tool jams in
the workpiece.
f Pay attention that the base plate 6 rests
securely on the material while sawing.
A jammed saw blade can break or lead to
kickback.
f When the cut is completed, switch off the
machine and then pull the saw blade out of
the cut only after it has come to a standstill.
In this manner you can avoid kickback and
can place down the machine securely.
f Use only sharp, flawless saw blades. Bent or
unsharp saw blades can break or cause kick-
back.
f Do not brake the saw blade to a stop by ap-
plying side pressure after switching off. The
saw blade can be damaged, break or cause
kickback.
f Use suitable detectors to determine if utility
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
f Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held
more secure than by hand.
f Keep your workplace clean. Blends of mate-
rials are particularly dangerous. Dust from
light alloys can burn or explode.
Page: 17
18 | English
2 609 003 951 | (6.10.09) Bosch Power Tools
f Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
f Never use the machine with a damaged
cable. Do not touch the damaged cable and
pull the mains plug when the cable is dam-
aged while working. Damaged cables in-
crease the risk of an electric shock.
f Products sold in GB only: Your product is
fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to
BS 1362).
If the plug is not suitable for your socket out-
lets, it should be cut off and an appropriate
plug fitted in its place by an authorised cus-
tomer service agent. The replacement plug
should have the same fuse rating as the
original plug.
The severed plug must be disposed of to
avoid a possible shock hazard and should
never be inserted into a mains socket else-
where.
Products sold in AUS and NZ only: Use a
residual current device (RCD) with a rated
residual current of 30 mA or less.
Functional Description
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Intended Use
The machine is intended for making separating
cuts and cut-outs in wood, plastic, metal, ce-
ramic plates and rubber while resting firmly on
the workpiece. It is suitable for straight and
curved cuts with mitre angles to 45°. The saw
blade recommendations are to be observed.
Product Features
The numbering of the product features refers to
the illustration of the machine on the graphics
page.
1 Lock-off button for On/Off switch
2 On/Off switch
3 Vacuum hose*
4 Vacuum connection
5 Saw blade storage
6 Base plate
7 Adjusting lever for orbital action
8 Switch for sawdust blowing device
9 Dust cover for vacuuming
10 “Cut Control” base
11 “Cut Control” viewing window
12 Handle (insulated gripping surface)
13 Saw blade holder
14 Guide roller
15 Saw blade*
16 Splinter guard*
17 Lead for the parallel guide
18 Contact protector
19 Screw
20 Scale for mitre angle
21 Parallel guide with circle cutter*
22 Locking screw for parallel guide*
23 Centring tip of the parallel guide*
24 Cutting mark, 0°
25 Cutting mark, 45°
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
Page: 18
English | 19
Bosch Power Tools 2 609 003 951 | (6.10.09)
Technical Data
Noise/Vibration Information
Measured sound values determined according
to EN 60745.
Typically the A-weighted noise levels of the
product are: Sound pressure level 85 dB(A);
Sound power level 96 dB(A). Uncertainty
K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Cutting board: Vibration emission value
ah=13 m/s2
, Uncertainty K=3 m/s2
,
Cutting sheet metal: Vibration emission value
ah=7 m/s2
, Uncertainty K=1.5 m/s2
.
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 21.09.2009
Jigsaw PST 800 PEL
Article number 3 603 CA0 1..
“Cut Control” z
Stroke rate control z
Orbital action z
Rated power input W 530
Output power W 290
Stroke rate at no load n0 min-1
500–3000
Stroke mm 20
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
mm
mm
mm
80
12
5
Bevel cuts (left/right),
max. ° 45
Weight according to
EPTA-Procedure
01/2003 kg 1.9
Protection class /II
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific
countries, these values can vary.
Please observe the article number on the type plate of
your machine. The trade names of the individual ma-
chines may vary.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Page: 19
20 | English
2 609 003 951 | (6.10.09) Bosch Power Tools
Assembly
f Before any work on the machine itself, pull
the mains plug.
Replacing/Inserting the Saw Blade
f When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching
the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be
found at the end of these instructions. Use only
T-shank saw blades or saw blades with 1/4" uni-
versal shank (U-shank). The saw blade should not
be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
f Clean the shank of the saw blade before
inserting it. An unclean shank cannot be fas-
tened securely.
If required, remove the dust cover 9 (see “Dust
Cover”).
Push the saw blade holder 13 upward in the
direction of the arrow. Insert the saw blade 15
(teeth in cutting direction) to the stop into the
saw blade holder.
While inserting the saw blade, pay attention that
the back of the saw blade is positioned in the
groove of the guide roller 14.
f Check the tight seating of the saw blade.
A loose saw blade can fall out and lead to in-
juries.
Removing the Saw Blade (see figure A2)
Push the saw blade holder 13 upward in the di-
rection of the arrow and remove the saw blade
15.
Saw Blade Storage (see figure B)
Up to six saw blades with lengths to 110 mm
can be stored in the saw blade storage 5. Insert
the saw blades with the T-shank into the recess
of the saw blade storage intended for this. Up to
three saw blades can be placed on top of each
other.
Shut the saw blade storage and slide it to the
stop into the opening of the base plate 6.
Splinter Guard (see figure C)
The splinter guard 16 (accessory) can prevent
fraying of the surface while sawing wood. The
splinter guard can only be used for certain saw
blade types and only for cutting angles of 0°.
When sawing with the splinter guard, the base
plate 6 must not be moved back for cuts that are
close to the edge.
Press the splinter guard 16 from the bottom into
the base plate 6.
“Cut Control”
“Cut Control” enables precise guiding of the
power tool along a cutting line marked on the
workpiece. The “Cut Control” kit includes the
viewing window 11 with cutting marks and the
base 10 for attachment to the power tool.
Attaching “Cut Control” to the Base Plate
(see figure D)
Clamp the “Cut Control” 11 viewing window in-
to the holders of the base 10. Then, lightly press
the base together and allow it to engage into the
lead 17 of the base plate 6.
Dust/Chip Extraction
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
– Use dust extraction whenever possible.
– Provide for good ventilation of the work-
ing place.
– It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Page: 20
English | 21
Bosch Power Tools 2 609 003 951 | (6.10.09)
Dust Cover (see figures E–F)
Mount the dust cover 9 before connecting the
machine to the dust extraction.
Mount the dust cover 9 onto the machine in
such a manner that the centre holder engages
on the contact protector 18 and the two outer
holders engage in the openings on the casing.
Remove the dust cover 9 for applications with-
out dust extraction as well as when performing
mitre cuts. For this, push the dust cover togeth-
er at the two outer holders and pull it off toward
the front.
Connecting the Dust Extraction
Place a vacuum hose 3 (accessory) onto the vac-
uum connection 4. Connect the vacuum hose 3
with a vacuum cleaner (accessory). An overview
for the connection of various vacuum cleaners
can be found at the end of these instructions.
Switch the saw dust blower off when a dust
extraction system is connected (see “Sawdust
Blower Device”).
The vacuum cleaner must be suitable for the
material being worked.
When vacuuming dry dust that is especially det-
rimental to health or carcinogenic, use a special
vacuum cleaner.
Operation
Operating Modes
f Before any work on the machine itself, pull
the mains plug.
Orbital Action Settings
The four orbital action settings allow for optimal
adaptation of cutting speed, cutting capacity
and cutting pattern to the material being sawed.
The orbital action can be adjusted with the ad-
justing lever 7, even during operation.
The optimal orbital action setting for the respec-
tive application can be determined through
practical testing. The following recommenda-
tions apply:
– Select a lower orbital action setting (or switch
it off) for a finer and cleaner cutting edge.
– For thin materials such as sheet metal, switch
the orbital action off.
– For hard materials such as steel, work with
low orbital action.
– For soft materials and when sawing in the
direction of the grain, work with maximum
orbital action.
Adjusting the Cutting Angle (see figure G)
The base plate 6 can be swivelled by 45° to the
left or right for mitre cuts.
The dust cover 9 and the splinter guard 16 can-
not be used when performing mitre cuts.
If required, remove the dust cover 9 (see “Dust
Cover”, page 21) and take off the splinter guard
16 (see “Splinter Guard”, page 20).
Pull the saw blade storage 5 out of the base
plate 6.
Loosen the screw 19 and lightly slide the base
plate 6 toward the vacuum connection 4.
For adjustment of precise mitre angles, the base
plate has adjustment notches on the left and
right at 0°, 22.5° and 45°. Swivel the base plate
6 to the desired position according to the scale
20. Other mitre angles can be adjusted using a
protractor.
Afterwards, push the base plate 6 to the stop in
the direction of the saw blade 15.
Tighten the screw 19 again.
No orbital action
Small orbital action
Medium orbital action
Large orbital action
Page: 21
22 | English
2 609 003 951 | (6.10.09) Bosch Power Tools
Cut Control for Bevel Cuts
For cutting-line control of bevel cuts, the “Cut
Control” viewing window 11 has a mark 24 for
0° right-angle cuts and a mark 25 each for the
left- or rightward sloping 45° bevel cut accord-
ing to scale 20.
The cutting mark for bevel cuts between 0° and
45° results proportionally. It can additionally be
drawn on the “Cut Control” viewing window 11
with a non-permanent marker, and easily be re-
moved again.
For accurate working, it is best to carry out a
test cut.
Offsetting the Base Plate (see figure G)
For sawing close to edges, the base plate 6 can
be offset to the rear.
Loosen the screw 19 and slide the base plate 6
toward the vacuum connection 4 to the stop.
Tighten the screw 19 again.
Sawing with the base plate 6 offset is possible
only at a 0° bevel angle. Additionally, “Cut Con-
trol” may not be used together with the base 10,
the parallel guide with circle cutter 21 (acces-
sory), as well as the splinter guard 16.
Sawdust Blower Device
With the air jet of the sawdust blower device 8,
the cutting line can be kept free of dust and chips.
Starting Operation of the Power Tool
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 2.
To lock the On/Off switch 2, keep it depressed
and push the lock-on button 1 to the right or left.
To switch off the machine, release the On/Off
switch 2. When the On/Off switch 2 is locked,
press it first and then release it.
Controling the Stroke Rate
Increasing or reducing the pressure on the
On/Off switch 2 enables stepless stroke-rate
control of the switched-on machine.
When the On/Off switch 2 is locked, it is not
possible to reduce the stroke rate.
The required stroke rate is dependent on the
material and the working conditions and can be
determined by a practical trial.
Reducing the stroke rate is recommended when
the saw blade engages in the material as well as
when sawing plastic and aluminium.
After longer periods of work at low stroke rate,
the machine can heat up considerably. Remove
the saw blade from the machine and allow the
machine to cool down by running it for approx.
3 minutes at maximum stroke rate.
0
˚
4
5
˚
4
5
˚
0˚
22,5˚
45˚
0
˚
4
5
˚
4
5
˚
24 25
11 10 6 20
Switching on the sawdust blow-
er device: For cuts in materials
with high removal rate, such as
in wood, plastic, etc., push the
switch 8 toward the vacuum
connection.
Switching off the sawdust blow-
er device: For cuts in metal and
when a dust extraction system is
connected, push the switch 8 to-
ward the saw blade.
Page: 22
English | 23
Bosch Power Tools 2 609 003 951 | (6.10.09)
Working Advice
f Before any work on the machine itself, pull
the mains plug.
f When working small or thin workpieces,
always use a stable support or a saw station
(Bosch PLS 300).
Plunge Cutting (see figure H)
f Plunge cuts may only be applied to soft
materials, such as wood, gypsum plaster
boards, etc.!
Use only short saw blades for plunge cutting.
Plunge cutting is possible only with the mitre
angle set at 0°.
Place the machine with the front edge of the
base plate 6 on to the workpiece without the
saw blade 15 touching the workpiece and
switch on. For machines with stroke rate con-
trol, select the maximum stroke rate. Firmly
hold the machine against the workpiece and by
tilting the machine, slowly plunge the saw blade
into the workpiece.
When the base plate 6 fully lays on the work-
piece, continue sawing along the desired cutting
line.
Parallel Guide with Circle Cutter (Accessory)
For cuts using the parallel guide with circle cut-
ter 21 (accessory), the thickness of the material
must not exceed a maximum of 30 mm.
Remove the “Cut Control” base 10 from base
plate 6. For this, lightly press the base together
and remove it from the guide 17.
Parallel Cuts (see figure I): Loosen the locking
screw 22 and slide the scale of the parallel guide
through the lead 17 in the base plate. Set the
desired cutting width as the scale value on the
inside edge of the base plate. Tighten the lock-
ing screw 22.
Circular Cuts (see figure J): Drill a hole (large
enough to accomodate the saw blade) close to
the cutting line within the circle to be sawn.
Work the drill hole with a router or file to ensure
that the saw blade faces flush against the cut-
ting line. Reposition the locking screw 22 on the
other side of the parallel guide. Slide the scale
of the parallel guide throught the lead 17 in the
base plate. Drill a hole in the centre of the cut-
out to be sawn. Insert the centring tip 23
through the inside opening of the parallel guide
and into the drilled hole. Adjust the radius as
scale value at the inside edge of the base plate.
Tighten the locking screw 22.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be
applied alongside cutting line because of the
material heating up.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
Clean the saw blade holder regularly. For this,
remove the saw blade from the machine and
lightly tap out the machine on a level surface.
Heavy contamination of the machine can lead to
malfunctions. Therefore, do not saw materials
that produce a lot of dust from below or over-
head.
f In extreme conditions, always use dust ex-
traction as far as possible. Blow out ventila-
tion slots frequently and install a residual
current device (RCD). When working metals,
conductive dust can settle in the interior of
the power tool. The total insulation of the
power tool can be impaired.
Lubricate the guide roller 14 occasionally with a
drop of oil.
Check the guide roller 14 regularly. If worn, it
must be replaced through an authorised Bosch
after-sales service agent.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
Page: 23
24 | English
2 609 003 951 | (6.10.09) Bosch Power Tools
After-sales Service and Customer
Assistance
Our after-sales service responds to your ques-
tions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-pt.com
Our customer service representatives can an-
swer your questions concerning possible appli-
cations and adjustment of products and acces-
sories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
E-Mail: rbsa-hq.pts@za.bosch.com
Disposal
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools
into household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national
right, power tools that are no longer usable
must be collected separately and disposed of in
an environmentally correct manner.
Subject to change without notice.
Page: 126
| 127
Bosch Power Tools 2 609 003 951 | (6.10.09)
T ... U ...
T 144 D
U 144 D
T 244 D
T 144 DP
T 101 B
U 101 B
T 118 B
U 118 B
T 123 X
U 123 X
T 127 D
U 127 D
T 345 XF
U 345 XF

Question & answers

There are no questions about the Bosch PST 800 PEL yet.

Ask a question about the Bosch PST 800 PEL

Have a question about the Bosch PST 800 PEL but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Bosch PST 800 PEL. Please make sure that you describe your difficulty with the Bosch PST 800 PEL as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.