Bosch PAM 19000 manual

View a manual of the Bosch PAM 19000 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Bosch
  • Product: Air-conditioning
  • Model/name: PAM 19000
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Swedish, Portuguese, Norwegian, Hungarian

Table of Contents

Page: 18
Table of contents
Environmental protection
Recommendations for the disposal
of packaging ....................................................................20
Recommendations for the disposal
of your old appliance........................................................20
Recommendations for saving energy ..............................20
Important Information
Before connecting your appliance....................................21
Your new appliance
Description of the appliance ............................................22
Control panel....................................................................23
Description of accessories................................................24
Requirements for use
Requirements for use ......................................................24
Transportation requirements ............................................25
Instructions for Use
Cooling..............................................................................25
Ways of releasing air outdoors ........................................26
Dehumidification ..............................................................28
Air purification ..................................................................29
Heating ............................................................................29
Cleaning and Maintenance
Cleaning the appliance ....................................................30
Cleaning and changing the purifying filters......................30
Storage requirements ......................................................31
Prior to use at change of season ....................................31
Things to check before calling the Technical
Service
General operation ............................................................31
Noise ................................................................................31
Technical service / Warranty /
Technical Information ..............................................32
19
Page: 19
20
20
Environmental protection
Recommendations for the disposal
of packaging
❏ Respect the environment when disposing of
the packaging your appliance comes
packed in.
❏ Our products are carefully packed for
transportation. All of the material used in
our packaging is environmentally friendly
(the cardboard is manufactured from used
paper) and may be recycled.
❏ Recycling packaging helps conserve raw
materials and reduces the amount of waste
produced in the world.
❏ Actively help protect the environment by
disposing of packaging properly. Take it to
your nearest local council disposal point or
it may be possible to return it to your
supplier.
Recommendations for the disposal
of your old appliance
❏ Unplug your appliance from the mains
electricity supply and cut the power cable.
❏ Appliances of this kind include both
recyclable material, which may be used
again, and hazardous products (such as
heavy metals and liquid refrigerants), which
may pollute the soil or the atmosphere.
Actively help protect the environment by
ensuring that your old appliance is disposed
of in accordance with environmentally
friendly practices. Dispose of your appliance
at an official disposal or recycling point (ask
your local council where the nearest
disposal point is). Appliances of this kind
contain refrigerants which must be disposed
of in accordance with current regulations.
❏ This appliance is labelled in accordance
with European Directive 2002/96/EG
concerning used electrical and electronic
appliances (waste electrical and electronic
equipment - WEEE).
The guideline determines the framework for
the return and recycling of used appliances
as applicable throughout the EU.
Recommendations for saving energy
Your appliance consumes energy when in use.
The consumption of energy produces an
environmental impact. Energy consumption
can be reduced enhancing the efficiency of
your appliance.
❏ Turn your air appliance off when it is not
needed.
❏ Select an ideal temperature; excessively
low temperatures result in high energy
consumption.
❏ Locate your appliance away from possible
heat sources (sunlight, etc.) and in a
position with good air circulation.
❏ Ensure that your appliance is installed
properly. The energy consumed can be cut
by up to 30% by reducing the entry of heat
into the room with awnings, blinds or
curtains on glazed surfaces.
❏ Use the accessories supplied with your
appliance and the specific accessories
described in “Description of accessories” in
order to minimise the entry of air from
outdoors. When using accessories which
require holes to be drilled in walls or
windows, the hole should be as precise as
possible and sealed with silicon, plaster or
similar material to prevent air from flowing
through any gaps.
Page: 20
Important Information
21
21
Before connecting your appliance
❏ Read the instructions book before using the
appliance for the first time. It contains
important information concerning not only
how to use the appliance, but also
maintenance and personal safety.
❏ Keep this instructions book. It may be
needed by another user at a later date.
❏ Do not use the appliance when damaged.
❏ Your appliance should be assembled and
connected to the mains electricity supply in
accordance with the assembly instructions
and current regulations. You may lose your
warranty if you fail to observe these
instructions.
❏ Our appliances are manufactured in
accordance with current safety regulations.
Only technicians instructed in these matters
are authorised to repair them. Your safety is
at stake.
❏ It is recommended that you follow the
manufacturer’s instructions concerning the
air expulsion tube (see “Ways of releasing
air outdoors”) in order to prevent efficiency
loss and unnecessary energy consumption.
❏ Avoid sharp bends on the air expulsion tube
and do not lengthen it more than necessary.
❏ When expelling hot air through sliding
windows, install the accessory which
prevents hot air entering the room from
outdoors and enhances efficiency.
❏ Make sure that the diffusion duct is
positioned in such a way that the window
can be closed as far as possible in order to
prevent air from outdoors entering the room.
❏ Check that the sleeves (collection and
diffusion) are correctly joined to the air
expulsion tube. See “Ways of releasing air
outdoors”
❏ Make sure that the air intakes and outlets
are not obstructed. Keep them clean and
free of dirt, dust and foreign objects.
❏ Make sure that the filters fitted on your
appliance are clean and installed properly
(see “Cleaning and Maintenance”).
❏ In the summer, ventilate the building when
the air outdoors is at its coolest (early
morning, night).
❏ Make sure that the drainage plug is fully
inserted. It may have come loose during
transportation, Fig. 1.
Fig. 1
Page: 21
22
Your new appliance
Description of the appliance
Diffusion duct
Basic filter
Hot air outlet
Air intake
Air intake
Cold air outlet
Front flap
Hot-air expulsion
tube
Cable housing
Characteristics plate
Handles
Air conditioning unit
Wheels
Purification filter
Condensed water
drainage pipe plug
Air expulsion tube
parking hook
Water drainage pipe
Flow director
Air expulsion tube parking
hook, only PAM17000
Fig. 2
Page: 22
23
Your new appliance
Control panel
20º 30º
ºC
0
Air outlet grille
Thermostat
Control knob
Full water tank
indicator light
0
Appliance off
Maximum cooling
Silent cooling
Dehumidification
Air purification
Heating
Fig. 3
Fig. 5
Model PAM18100
0 Appliance off
Maximum cooling
Silent cooling
Dehumidification
Silent air purification
Maximum air purification
Fig. 4
Model PAM17000 / PAM19000
Page: 23
24
Your new appliance
Description of accessories
Suction Base Purifying Double Wall grommet Sliding
pad filter Filter active Window balcony
filter grommet accessory
Art. Nr.: Art. Nr.: Art. Nr.:
PAZ10000 PAZ11000 475075
PAM17000
• • *
PAM19000
• • *
PAM18100
• • *
Approx.
measurement ø wall
min / max 10,5 70x10/
(length x 205x10
width) cm.
Standard accessories: These accessories are supplied with the appliance.
•Optional accessories: These accessories are available for purchase from the
manufacturer's official technical service and authorised distributors.
*Optional accessories: These accessories are only available for purchase from the
manufacturer's official technical service.
Requirements for use
Condiciones de utilización
❏ This home appliance should be connected
to a 220/240 V, 50 Hz mains electricity
supply via an earthed socket.
❏ It must be protected with a 10 A slow-action
fuse.
❏ Should an extension lead be required, then
this lead should be at least 1.5 mm2
thick
per terminal, less than 25 m long and
earthed.
❏ There is a cavity at the back of the
appliance to house the mains electricity
supply cable. See Fig. 2.
❏ Do not allow water to enter your appliance
and do not cover the air intakes/outlets.
❏ For safety reasons, the appliance must be
at least 20 cm away from any nearby
surface before it is turned on, Fig. 6.
mín.
20 cm. mín.
20 cm.
Fig. 6
Warning!
The mains electricity supply connection
cable must only be replaced by authorised
members of the manufacturer’s Official
Technical Service.
Page: 24
25
Requirements for use
When the appliance is turned off and then
turned back on, it takes the compressor 3
minutes to start up again. This period of
time is required in order to ensure correct
operation.
Avoid direct contact with the air expelled
through the expulsion tube.
Transportation requirements
The appliance is fitted with wheels to make it
easier to move around. If necessary, you can
tilt the appliance in order to move it. You
should not turn the appliance back on again
for a minimum period of one hour after
performing this procedure.
❏ Before tilting it, empty the condensed water
from the internal tank by extracting the
water drainage pipe from its housing and
removing the plug, Fig. 7. Do not forget to
replace the plug and reinsert the pipe in its
housing when the tank is empty.
Instructions for Use
Cooling
The appliance cools and dehumidifies the air
in the room at the same time in order to create
a pleasant atmosphere.
❏ Plug the appliance into the mains electricity
supply.
❏ Lead the hot air expulsion tube outside. In
order to avoid excessive noise and
efficiency loss, the air expulsion tube should
be positioned as shown in Fig. 14. See
“Ways of releasing air outdoors”.
❏ Check that the plug, Fig. 1, is fitted on the
drainage pipe to prevent water from leaking
onto the support surface.
❏ Lift the air director on the top of the
appliance. This air director is not installed
on the appliance on PAM18100 models.
See figures 25 and 26 in “Heating”.
❏ Select the maximum or silent
cooling function, Fig. 8. (The silent cooling
function reduces the air flow on the
appliance).
❏ Set the thermostat to the desired
temperature, Fig. 9. If the appliance turns
itself off automatically because the
thermostat trips, it is necessary to wait for
ambient temperature to rise 2-3°C before it
comes back on again.
Fig. 7
0
Fig. 8
20° 30°
°C
Fig. 9
Page: 25
In order to fit the expulsion tube assembly
properly in its housing, it is necessary to slide
the sleeve into the positioning slot (as shown
by the arrows on Fig. 12).
The diffusion duct, Fig. 10, is added when the
tube assembly has been fitted onto the
appliance.
Press the “Push” tab (Fig. 13, 1) and slide out
(Fig, 13, 2) to remove the assembly from the
appliance.
Temporary installation
❏ Open the window slightly and position the
diffusion duct between the jamb and the
glaze frame.
❏ Close the window as far as possible and
secure it with the suction pad supplied,
Fig. 14.
Fig. 12
Fig. 13
Fig. 14
26
Instructions for Use
During air conditioning, some of the
condensed water produced evaporates
automatically and is expelled outdoors
together with the expelled air through the hot
air expulsion tube.
In conditions of extreme humidity, the
appliance accumulates condensed water in an
internal tank. When a certain level is reached
an indicator light, Fig. 3, comes on indicating
that the condensed water tank is full and
needs to be emptied. When this happens, the
appliance stops cooling the air in the room
until the water is drained, as explained in
“Transportation requirements”, Fig. 7.
❏ It is recommended that you turn the
appliance off while draining the water.
Warning!
Remember that when the appliance is
turned off and turned back on, it is
necessary to wait for approximately 3
minutes before the compressor starts up
again. This period of time is required in
order to ensure correct appliance
operation.
Ways of releasing air outdoors
Fitting the air expulsion tube and
accessories onto the appliance
Fit the air expulsion tube assembly into the
housing on the top of the appliance at the
back, Fig. 11.
Housing for the
air expulsion
assembly
Fig. 10 Fig. 11
Page: 26
27
Instructions for Use
❏ Remove the diffusion sleeve and connect
the air expulsion tube to the accessory.
❏ If permanent installation is to be performed
through the window, then it is only
necessary to use the transparent end piece
on the accessory. A 10.5-cm diameter hole
needs to be cut in the glass, Fig. 18.
• The sliding window/balcony installation
accessory can also be used (See
“Description of accessories”). Fig. 15: a, b,
c, d. This accessory can be used for both
horizontal and vertical windows / balconies.
a
b
c
d
Fig. 15
• The accessory has two holes on the side to
fit it to the window / balcony with. The user
can secure it to the frame or wall with two
screws (not included with the accessory) to
prevent it from moving or falling out of place,
Fig. 16.
Notes
Do not extend the hot air expulsion tube
more than necessary (maximum length;
140 cm).
Fig. 16
Permanent installation
Permanent installation is performed using the
wall grommet / window grommet. See
"Description of accessories".
❏ To expel hot air through the wall, it is
necessary to make a hole in the wall and fit
the wall grommet, Fig. 17.
24 - 38 cm. Fig. 17
Fig. 18
Page: 27
Dehumidification
In position , the appliance reduces the
humidity in the atmosphere.
❏ Set the thermostat to its minimum
temperature setting, Fig. 20.
❏ Place a bowl at the drainage pipe outlet and
remove the plug to collect the condensed
water, Fig. 21
Warning!
The amount of dehumidified water may
reach a maximum of 36 litres in 24 hours,
depending on ambient conditions. See
“Technical Information”.
❏ Remove the diffusion duct and set the air
expulsion tube to the position shown in
figure 22.
❏ The expulsion tube may also be totally
dismantled if desired.
❏ Lift the air director on the top of the
appliance. This air director is not installed
on the appliance on PAM18100 models.
See figures 25 and 26 in “Heating”.
❏ Select the dehumidification function on
the control knob, Fig. 23.
0
28
Instructions for Use
Do not form sharp bends when positioning
the tube, otherwise the correct expulsion
of hot air may be impeded. This may cause
a reduction in the cooling power and
performance of the appliance.
In order to achieve maximum cooling
efficiency and minimum noise levels, the
expulsion tube should be fitted above the
total height of the appliance, Fig. 19.
Fig. 19
20° 30°
°C
Fig. 20
Fig. 23
Fig. 21
Fig. 22
Page: 28
29
Instructions for Use
❏ Select the heating function, Fig. 27.
❏ Set the thermostat to the desired
temperature. When this temperature is
reached, the appliance turns itself off
automatically. It comes back on again when
the temperature drops 2-3ºC.
Warning!
Do not cover the air intakes or outlets on
your appliance!
❏ When the appliance or the model is fitted
with optional filters, we recommend that
these be left on regardless of the function
selected (cooling, dehumidification, air
purification) in order to purify the air more
effectively.
Note:
Due to the internal configuration of the
PAM17000 models, air is also expelled
outdoors when the appliance is set to the
ventilation function. In order to reduce the
noise produced, it is recommended that you
remove the air expulsion tube.
Heating (only on PAM18100)
When set to position , the appliance heats
the air in the room until the temperature set by
the user is reached. The air in the room is
purified at the same time.
❏ Plug the appliance into the mains electricity
supply.
❏ Put the air expulsion tube in the same position
as for dehumidification.
❏ This air director is not installed on the
appliance on PAM18100 models. The
manufacturer recommends that an air
director be previously installed in order to
distribute the air flow better. The director is
fitted as shown in the following figures.
Do not forget to replace the plug onto the
water drainage pipe when you change
function, otherwise the appliance will shed
water when operated.
Remember that ambient temperature must
be 18ºC or higher in order for the appliance
to work.
Air purification
The air entering the room (ventilation) is
circulated through a purifying filter when the
appliance is set to this function.
The appliance is fitted with a basic filter and a
purifying filter for:
- Pollen, bacteria and dust.
❏ Put the air expulsion tube in the same
position as for dehumidification.
❏ Lift the air director on the top of the
appliance. This air director is not installed
on the appliance on PAM18100 models.
See figures 25 and 26 in “Heating”.
❏ Select the purifying speed: maximum or
silent , Fig. 24.
0
Fig. 24
Fig. 25
Fig. 26
0
Fig. 27
Page: 29
Apurifying filter is also fitted inside the basic filter
on some models.
This purifying filter needs to be changed every
year in order to remain operational.
(These accessories are available for purchase
from the Manufacturer's Official Technical
Service and authorised distributors). See
“Description of accessories”.
Installing the purifying filter:
❏ Remove the basic filter from the appliance,
Fig. 30.
❏ Fit the purifying filter inside the basic filter
as shown in Fig. 31.
❏ Install the assembly onto the appliance by
lining the lower studs up with the slots on
the front casing of the appliance and
pressing the top clip in until it clicks into
position. The assembly is fitted properly
when it clicks into position.
❏ Close the front flap.
❏ In order to maintain cooling power, only fit
one set of filters onto the support.
Note
The front flap can also be removed in order
to clean the appliance or change the filters
more easily.
30
Cleaning and Maintenance
Cleaning the appliance
❏ For safety reasons, you should unplug the
appliance from the mains electricity supply
before cleaning.
❏ The appliance can be cleaned with a cloth
or sponge, slightly warm water and a mild
detergent.
❏ Never use hot water (more than 40ºC),
bleach, benzene, petrol, acid, scouring
pads, brushes or strong detergents. Prevent
water from entering the appliance.
❏ Do not clean the appliance with a hose.
Cleaning and changing the purifying
filters
Press the side tabs, (Fig. 28, 1.), on the front
flap of the appliance and pull it open (it is not
necessary to remove it), (Fig. 28, 2.). The flap
is fitted with a stop and can be opened up to
this point without risk of falling.
All models are fitted with a basic filter which
needs to be cleaned regularly, Fig. 29. The
filter is accessed by pressing the tab at the top
and removing it from its housing, Fig. 30. The
filter is cleaned under a cold tap, dried and
replaced.
Washable
basic filter
Purifyng
filter
Fig. 28
Fig. 29
Fig. 30
Fig. 31
Page: 30
31
Cleaning and Maintenance
To do this, open the flap up to the safety stop
(the flap opens to a slight angle, Fig. 28) and
pull outwards. In order to refit it, line the
lower studs on the flap up with the holes on
the casing until the studs meet the clips on
the casing.
Storage requirements
When the appliance is out of use for a long
period, set the expulsion tube to parking
position so that the appliance takes up as little
space as possible.
❏ To do this, bend the tube towards the back
of the appliance and secure it with the
diffusion hook. Figs. 32 and 33.
Prior to use at change of season
❏ Clean the air filter.
❏ Clean the casing and the grilles if
necessary.
Fig. 32
Fig. 33
Things to check before calling the Technical Service
General requirements for operation
What to do if...
... the appliance does not work ...
❏ Check that it is plugged in properly.
❏ Make sure that the control knob is not set to
off .
❏ Check that the mains electricity supply is
working. Check the fuse box.
❏ Set the thermostat to a lower temperature.
... the appliance does not work and the light
indicating that the condensed water tank is
full is on ...
❏ Set the appliance on a flat surface. If the
light does not go out, empty the internal
water tank. (See instructions in “cooling”).
... the appliance does not reduce room
temperature sufficiently ...
❏ Check the joins on the hot air expulsion tube.
❏ Make sure that the expulsion tube is not too
bent and that it is not extended to more
than 140 cm.
❏ Make sure that the plug is fitted on the
drainage water pipe.
❏ Fit the suction pad to close the window as
far as possible.
❏ Lower blinds to reduce direct sunlight.
... there is water on the control panel grille
or on the basic filter housing ...
❏ There is no cause for concern. This is
normal.
Noise
... the appliance makes a lot of noise ...
Some noise is normal and other types of noise
can be solved easily. You need to be able to
distinguish between these types of noise:
Page: 31
Technical service / Warranty / Technical Information
Technical service
Should your appliance fail to work properly and
all the instructions for use and installation
(especially the section headed
"Requirements....") have been carefully
observed, then remember that our Technical
Service Network is at your full disposal.
When contacting the Technical Service, quote
the model code (E-NR) and the appliance’s
factory number (FD). This information can be
found on characteristics plate, Fig. 2.
Warranty
The conditions of warranty depend on the
relevant Supplier in a particular country. Contact
the establishment where you purchased your
appliance for more information and quote the
appliance model and factory number. The receipt
of purchase for the appliance must be produced
prior to any work carried out under warranty.
Technical Information
32
Things to check before calling the Technical Service
Perfectly normal noise
❏ The sound of water flowing in cycles is due to
the pump, which circulates the water to
enhance the power of the appliance.
❏ A dull, humming sound is inevitable due to the
compressor.
❏ A faint, whistling sound is due to the
refrigerant passing through the thinner pipes
on the appliance when the compressor starts
up.
❏ A short clicking sound is produced when the
pump connects and disconnects or when the
regulator connects or disconnects the
electronics system.
Easy-to-solve noises
❏ Make sure that the air expulsion tube and the
diffusion and collection sleeves are fitted
properly onto the appliance.
❏ Make sure that the air intakes and outlets on
the appliance are free of obstacles.
❏ Make sure that the appliance is not in direct
contact with furniture or other appliances. The
air output may be flowing directly onto these
and thereby increasing the noise level.
Any other type of fault or repair work should be
dealt with by a specialised Technician. Get in
touch with your authorised dealer, customer
service or the Technical Service Network.
Model PAM17000 PAM19000 PAM18100
Consumption at maximum power (W)* 800 975 975
Cooling capacity (W)* 1700 1900 1800
Dehumidification capacity (l./day) 31 36 36
Power in heating mode (W) – – 1800
Fuse (A) 10 10 10
Energy efficiency (letter) D D D
Working range
- Cooling (min./max. °C) 20 – 35 20 – 35 20 – 35
- Dehumidification (min./max. °C) 18 – 35 18 – 35 18 – 35
(*) per EN14511

Question & answers

There are no questions about the Bosch PAM 19000 yet.

Ask a question about the Bosch PAM 19000

Have a question about the Bosch PAM 19000 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Bosch PAM 19000. Please make sure that you describe your difficulty with the Bosch PAM 19000 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.