Bosch GSA 18 V-LI Professional manual

View a manual of the Bosch GSA 18 V-LI Professional below. All manuals on can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Bosch
  • Product: Saw
  • Model/name: GSA 18 V-LI Professional
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Swedish, Portuguese, Danish, Polish, Russian, Norwegian, Finnish, Czech, Romanian, Turkish, Slovak, Greek, Hungarian, Slovene, Croatian, Ukrainian,

Table of Contents

Page: 2
3 |
1 609 92A 01E | (21.11.12) Bosch Power Tools Page 3 Wednesday, November 21, 2012 10:31 AM
Page: 3
1 609 92A 01E | (21.11.12) Bosch Power Tools
4 |
9 8
7 Page 4 Wednesday, November 21, 2012 10:31 AM
Page: 4
5 |
1 609 92A 01E | (21.11.12) Bosch Power Tools
A Page 5 Wednesday, November 21, 2012 10:31 AM
Page: 11
12 | English
1 609 92A 01E | (21.11.12) Bosch Power Tools
Elektrowerkzeuge, Akkus, Zubehör und Verpackun-
gen sollen einer umweltgerechten Wiederverwertung
zugeführt werden.
Werfen Sie Elektrowerkzeuge und Akkus/Batterien nicht in
den Hausmüll!
Nur für EU-Länder:
Gemäß der europäischen Richtlinie
2002/96/EG müssen nicht mehr ge-
brauchsfähige Elektrowerkzeuge und ge-
mäß der europäischen Richtlinie
2006/66/EG müssen defekte oder ver-
brauchte Akkus/Batterien getrennt gesam-
melt und einer umweltgerechten Wieder-
verwendung zugeführt werden.
Nicht mehr gebrauchsfähige Akkus/Batterien können direkt
abgegeben werden bei:
Recyclingzentrum Elektrowerkzeuge
Osteroder Landstraße 3
37589 Kalefeld
Batrec AG
3752 Wimmis BE
Bitte beachten Sie die Hinweise im Ab-
schnitt „Transport“, Seite 11.
Änderungen vorbehalten.
Safety Notes
General Power Tool Safety Warnings
Read all safety warnings and all in-
and instructions may result in electric shock, fire and/or seri-
ous injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
Work area safety
 Keepworkareacleanandwelllit.Clutteredordarkareas
invite accidents.
 Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
 Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Electrical safety
 Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
 Avoidbodycontactwithearthedorgroundedsurfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
 Do not expose power tools to rain or wet conditions.
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges and moving parts. Damaged
or entangled cords increase the risk of electric shock.
 When operating a power tool outdoors, use an exten-
for outdoor use reduces the risk of electric shock.
 If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
Personal safety
 Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
alcohol or medication. A moment of inattention while op-
erating power tools may result in serious personal injury.
 Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal inju-
 Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or en-
ergising power tools that have the switch on invites acci-
 Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
 Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
 Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelleryor long hair can be
caught in moving parts.
 If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
WARNING Page 12 Wednesday, November 21, 2012 10:31 AM
Page: 12
English | 13
Bosch Power Tools 1 609 92A 01E | (21.11.12)
Power tool use and care
 Donotforcethepowertool.Usethecorrectpowertool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
 Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
 Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
 Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
 Keepcuttingtoolssharpandclean.Properlymaintained
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
 Recharge only with the charger specified by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another bat-
tery pack.
 Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create a
risk of injury and fire.
 When battery pack is not in use, keep it away from oth-
er metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
 Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addition-
ally seek medical help. Liquid ejected from the battery
may cause irritation or burns.
 Haveyourpowertoolservicedbyaqualifiedrepairper-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
Safety Warnings for Sabre Saws
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
 Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can
lead to injuries.
 Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
 When sawing, the adjustable footplate 2 must always
faces against the workpiece. The saw blade can become
wedged and lead to loss of control over the machine.
 When the cut is completed, switch off the machine and
then pull the saw blade out of the cut only after it has
come to a standstill. In this manner you can avoid kick-
back and can place down the machine securely.
 Useonlyundamagedsawbladesthatareinperfectcon-
dition. Bent or dull saw blades can break, negatively influ-
ence the cut, or lead to kickback.
 Do not brake the saw blade to a stop by applying side
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
 Clamp material well. Do not support the workpiece
with the the saw running. Danger of kickback.
 Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
 In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
 Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
 Use only original Bosch batteries with the voltage list-
edonthenameplateofyourpowertool. Whenusingoth-
er batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries. Page 13 Wednesday, November 21, 2012 10:31 AM
Page: 13
14 | English
1 609 92A 01E | (21.11.12) Bosch Power Tools
Product Description and
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for sawing wood, plastic, metal and
building materials while resting firmly on the workpiece. It is
suitable for straight and curved cuts. When using the appro-
priate bimetal saw blades, it is possible to cut flush to the
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Saw blade*
2 Adjustable footplate
3 Saw blade holder
4 Locking sleeve for saw blade
5 Stroke rod
6 Stroke speed selector switch
7 On/Off switch
8 Battery unlocking button
9 Battery pack*
10 Handle (insulated gripping surface)
11 Button for charge-control indicator*
12 Battery charge-control indicator*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 77 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K
determined according to EN 60745:
Cutting board: ah=24 m/s2
, K=1.5 m/s2
Cutting wooden beam: ah=24.5 m/s2
, K=1.5 m/s2
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 andmay be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
Identify additional safety measures to protect the operator
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 25.10.2012
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
Sabre saw GSA 18 V-LI
Article number 3 601 F4J 0..
Rated voltage V= 18
Stroke rate at no load n0
– 1st gear
– 2nd gear
0 –2400
0 –2700
Tool holder SDS
Stroke rate control 
Stroke mm 28
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to
EPTA-Procedure 01/2003 kg 3.2/3.4*
* dependent of the battery pack being used
Dr. Egbert Schneider
Senior Vice President
Helmut Heinzelmann
Head of Product Certification
PT/ETM9 Page 14 Wednesday, November 21, 2012 10:31 AM
Page: 14
English | 15
Bosch Power Tools 1 609 92A 01E | (21.11.12)
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the battery
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 8 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
12 indicate the charge condition of the battery 9. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 11 to indicate the charge condition. This is also
possible when the battery 9 is removed.
When no LED lights up after pushing button 11, then the bat-
tery is defective and must be replaced.
Replacing/Inserting the Saw Blade
 Beforeanyworkonthepowertool,removethebattery.
 Whenmountingthesawblade,wearprotectivegloves.
Danger of injury when touching the saw blade.
 When changing the saw blade, take care that the saw
blade holder is free of material residue, e. g. wood or
metal shavings.
Selecting a Saw Blade
Use only saw blades suitable for the material being worked.
An overview of recommended saw blades can be found at the
beginning of these instructions. Use only ½" universal shank
for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure B)
Press the saw blade 1 firmly into the saw blade holder 3 until
it can clearly be heard to engage. This causes the locking
sleeve 4 to turn by approx. 90° and locks the saw blade.
If the saw blade 1 is not locked, turn the locking sleeve 4 ap-
prox.90° inthedirectionofthearrowuntilitlocksintheopen
position and a “click” can be heard. Then press the saw blade
1 into the saw blade holder 3 again.
 Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
For certain work, the saw blade 1 can also be turned through
180° (withtheteethpointedupwards)andre-insertedagain.
Ejecting the Saw Blade (see figure C)
 When ejecting the saw blade, hold the machine in such
a manner that no persons or animals can be injured by
the ejected saw blade.
Turn the locking sleeve 4 approx. 90° in the direction of the
arrow. The saw blade 1 is ejected.
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Starting Operation
Inserting the battery
 Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool. Us-
ing other batteries can lead to injuries and pose a fire haz-
To protect the machine against unintentional starting, set the
stroke speed selector switch 6 to the centre position. Insert
the charged battery 9 from the front into the handle of the
power tool. Push the battery completely into the handle until
the red stripe can no longer be seen and the battery is secure-
ly locked.
Changing the Stroke Speed Setting
The stroke speed setting of the power tool can be changed
with the stroke speed selector switch 6. However, this is not
possible when the On/Off switch 7 is pressed.
LED Capacity
Continuous lighting 3 x green 2/3
Continuous lighting 2 x green 1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green Reserve Page 15 Wednesday, November 21, 2012 10:31 AM
Page: 15
16 | English
1 609 92A 01E | (21.11.12) Bosch Power Tools
Stroke speed selector switch 6 – central position:
The safety lock is activated.
The On/Off switch 7 is blocked and the machine
is secured against being switched on uninten-
Stroke speed selector switch 6 – left:
1. Gear, low stroke speed.
The low stroke speed is suitable for sawing hard
materials such as steel, non-ferrous metal, hard
plastics or for precision cuts in wood and plunge
The low stroke speed enables sawing with less
Stroke speed selector switch 6 – right:
2. Gear, high stroke speed.
The high stroke speed is suitable for sawing soft
The high stroke speed enables quicker opera-
tional progress, e. g., for coarse cuts in wood.
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it
To switch off the machine, release the On/Off switch 7.
To save energy, only switch the power tool on when using it.
Controlling the Stroke Rate
Increasing or reducing the pressure on the On/Off switch 7
enables stepless stroke-rate control of the switched-on ma-
Reducing the stroke rate is recommended when the saw
blade engages in the material as well as when sawing plastic
and aluminium.
Protection Against Deep Discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Working Advice
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Pivoting Footplate (see figure D)
Due to its movability, the adjustable footplate 2 adapts to the
required angular position of the surface.
 When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.
objects such as nails, screws or similar, and remove them, if
sition the footplate 2 onto the surface of the work and saw
through the material applying uniform contact pressure and
feed. After completing the working procedure, switch the ma-
chine off.
If the saw blade should jam, switch the machine off immedi-
ately. Widen the gap somewhat with a suitable tool and pull
out the machine.
Plunge Cutting (see figure E)
 The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!
Use only short saw blades for plunge cutting.
Place the machine with the edge of the footplate 2 onto the
workpiece and switch on. For power tools with stroke speed
control, set the maximum stroke speed. Press the power tool
plunge into the workpiece.
piece, continue sawing alongside the desired cutting line.
For certain work, the saw blade 1 can also be inserted turned
throughby180° andthesabresawcanbeguidedaccordingly
in a reversed manner.
Flush Cuts (see figure F)
Using elastic bimetal saw blades, items still attached to a wall
(e. g. projecting building elements such as water pipes, etc.)
can be sawn off flush at the wall.
 Pay attention that the saw blade always extends be-
yond the diameter of the material being worked. There
is danger of kickback.
Position the saw blade directly against the wall and apply
some lateral pressure via the tool until the footplate faces
against the wall. Switch the power tool on and saw through
the workpiece, applying constant lateral pressure.
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
0 °Cand50 °C.Asanexample,donotleavethebatteryinthe
car in summer.
clean and dry brush.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal. Page 16 Wednesday, November 21, 2012 10:31 AM
Page: 16
English | 17
Bosch Power Tools 1 609 92A 01E | (21.11.12)
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 For safe and proper working, always keep the machine
and ventilation slots clean.
a soft brush. Remove the saw blade from the power tool for
this. Ensure proper operation of the saw blade holder by ap-
plying a suitable lubricant.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
If the machine should fail despite the care taken in manufac-
an after-sales service centre for Bosch power tools.
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Tel.: (011) 4939375
Fax: (011) 4930126
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Tel.: (031) 7012120
Fax: (031) 7012446
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Tel.: (021) 5512577
Fax: (021) 5513223
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: Page 17 Wednesday, November 21, 2012 10:31 AM
Page: 17
18 | English
1 609 92A 01E | (21.11.12) Bosch Power Tools
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Tel.: (021) 46832522
Fax: (021) 46828645/6823
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio Global City,
1634 Taguig City, Philippines
Tel.: (02) 8703871
Fax: (02) 8703870
Bosch Service Center:
9725-27 Kamagong Street
San Antonio Village
Makati City, Philippines
Tel.: (02) 8999091
Fax: (02) 8976432
Robert Bosch (S.E.A.) Sdn. Bhd.
No. 8A, Jalan 13/6
G.P.O. Box 10818
46200 Petaling Jaya
Selangor, Malaysia
Tel.: (03) 79663194
Fax: (03) 79583838
Toll-Free: 1800 880188
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: 02 6311879 – 1888 (10 lines)
Fax: 02 2384783
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501, Thailand
Bosch Service – Training Centre
2869-2869/1 Soi Ban Kluay
Rama IV Road (near old Paknam Railway)
Prakanong District
10110 Bangkok
Tel.: 02 6717800 – 4
Fax: 02 2494296
Fax: 02 2495299
Robert Bosch (SEA) Pte. Ltd.
11 Bishan Street 21
Singapore 573943
Tel.: 6571 2772
Fax: 6350 5315
Toll-Free: 1800 3338333
Robert Bosch Vietnam Co. Ltd
10/F, 194 Golden Building
473 Dien Bien Phu Street
Ward 25, Binh Thanh District
84 Ho Chi Minh City
Tel.: (08) 6258 3690 ext. 413
Fax: (08) 6258 3692
The contained lithium-ion batteries are subject to the Danger-
ous Goods Legislation requirements. The user can transport
the batteries by road without further requirements.
forwarding agency), special requirements on packaging and
labelling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery in
such a manner that it cannot move around in the packaging.
Please also observe possibly more detailed national regula-
The machine, rechargeable batteries, accessories
and packaging should be sorted for environmental-
friendly recycling.
Do not dispose of power tools and batteries/rechargeable
batteries into household waste! Page 18 Wednesday, November 21, 2012 10:31 AM
Page: 188
1 609 92A 01E | (21.11.12) Bosch Power Tools
189 |
AL 1860 CV (14,4 / 18 V)
2 607 225 322 (EU)
2 607 225 324 (UK)
2 607 225 326 (AUS)
2 607 225 334 (KOR)
AL 1820 CV (14,4 / 18 V)
2 607 225 424 (EU)
2 607 225 426 (UK)
2 607 225 428 (AUS)
2 608 438 694
(L-BOXX 374)
18 V (Li-Ion) Page 189 Wednesday, November 21, 2012 10:31 AM

Question & answers

There are no questions about the Bosch GSA 18 V-LI Professional yet.

Ask a question about the Bosch GSA 18 V-LI Professional

Have a question about the Bosch GSA 18 V-LI Professional but cannot find the answer in the user manual? Perhaps the users of can help you answer your question. By filling in the form below, your question will appear below the manual of the Bosch GSA 18 V-LI Professional. Please make sure that you describe your difficulty with the Bosch GSA 18 V-LI Professional as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.