Black & Decker Spacemaker CO75 manual

Select a language NL 100%

View a manual of the Black & Decker Spacemaker CO75 below. All manuals on can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Black & Decker
  • Product: Tin opener
  • Model/name: Spacemaker CO75
  • Filetype: PDF
  • Available languages: , ,

Table of Contents

Page: 0
Please Read and Save this Use and Care Book
Por favor lea este instructivo antes de usar el producto
Veuillez lire et conserver ce guide d’entretien et d’utilisation
Can Openers
Accessories/Parts (USA/Canada)
Accesorios/Partes (EE.UU/Canadá)
Accessoires/Pièces (É.-U./Canada)
❑ CO75
❑ CO85
❑ CO85BM
USA/Canada 1-800-231-9786
Mexico 01-800-714-2503
CO75Pub600066R1 7/21/06 3:18 PM Page 1
Page: 1
When using electrical appliances, basic safety precautions should always be
followed, including the following:
❑ Read all instructions.
❑ To protect against electrical hazards, do not immerse appliance in water
or other liquid.
❑ Close supervision is necessary when any appliance is used by or near
❑ Unplug from outlet when not in use, before putting on or taking off parts,
and before cleaning.
❑ Avoid contact with moving parts.
❑ Do not operate any appliance with a damaged cord or plug, or after the
appliance malfunctions, or has been dropped or damaged in any manner.
Return appliance to the nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
❑ The use of attachments not recommended or sold by the appliance
manufacturer may cause fire, electric shock or injury.
❑ Do not use outdoors.
❑ Do not let cord hang over edge of table or counter or touch hot surfaces.
❑ Do not open pressurized (aerosol-type) cans.
❑ Do not open cans of flammable liquids such as lighter fluids
❑ Do not use appliance for other than intended use.
❑ To reduce the risk of fire or electric shock, do not operate any heating
appliance beneath the mounted unit.
❑ Do not mount the storage bracket/unit over or near any portion of a heating
or cooking appliance or a sink or basin.
This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to fit into a polarized outlet only one
way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
The cord of this appliance was selected to reduce the possibility of tangling in
or tripping over a longer cord. If more length is needed, use an extension cord
rated no less than 15-amperes. (For 220 volts rated products, use an extension
cord rated no less than 6-amperes). When using an extension cord, do not let
it drape over the working area or dangle where someone could accidentally trip
over it. Handle cord carefully for longer life; avoid jerking or straining it at outlet
and appliance connections.
Warning : This appliance is equipped with a tamper-resistant screw to prevent
removal of the outer cover. To reduce the risk of fire or electric shock, do not
attempt to remove the outer cover. There are no user-serviceable parts inside.
Repair should be done only by authorized service personnel.
Note: If the power supply cord is damaged, it should be replaced by qualified
personnel or in Latin America by an authorized service center.
CO75Pub600066R1 7/21/06 3:18 PM Page 2
Page: 2
Product may vary slightly from what is illustrated.
How to Use
This product is for household use only.
Important: For warranty verification, do not remove line cord sticker.
1. Remove the unit from the cardboard packaging.
2. Remove the blade assembly from cardboard insert and any stickers attached to the
blade assembly. To replace blade assembly, follow instructions under Care and
Cleaning, Replacing Blade Assembly.
3. Verify that you have received 4 mounting washers with 4 mounting screws,
(2) 1/2" and (2) 1/4" spacer mounting assemblies.
Important: Do not try to open cans or sharpen knives unless the unit is properly
When selecting a mounting location:
• Consider your normal work pattern and the possible addition of other under-the-
cabinet appliances.
• To reduce risk of fire or electric shock, do not place any heating or cooking appliance
under the unit.
• Do not mount near or over a sink.
• Do not mount the unit behind, under or in front of under-cabinet lighting appliances.
• Be sure to mount the can opener within reach of an electrical outlet.
1. First, determine if your cabinet has a flat bottom (A) —or an
overhang (lip extending down) bottom (B).
2. If your cabinet has a flat bottom, you will need to use one
1/2" spacer mounting assembly.
3. If it has an overhang, measure the overhang with a ruler to
determine how many 1/2" or 1/4"spacer mounting assemblies
you will need. For example, if the measurement is 1", then use
two 1/2" spacer mounting assemblies.
4. With the doors of the cabinet open, use the spacer mounting
assembly as a guide to mark one rear and one front hole.
5. a. If your cabinet has an overhang:
Slide the mounting assembly forward until one side of the
assembly touches the inside surface of the overhang.
b. If your cabinet has a flat bottom:
Place the mounting assembly approximately 1/4"-1/2" back
from the front edge of the cabinet. Important: Be sure the
can opener is not set too far back.
6. Close the cabinet door, hold the unit up to the cabinet floor,
and lift the lever to be sure it clears the cabinet door (C).
1. Locating post (not shown)
2. Cord storage (not shown)
3. Piercing lever
4. Knife sharpener (Models CO85 & CO85BM)
† 5. Blade assembly with magnet
White Blade (Part# CO75-01)
Black Blade (Part# CO85BM-01)
6. Bottle opener
† 7. 4 mounting washers and 4 mounting screws
(2) 1/2", (2) 1/4" spacer mounting assemblies
(Part # CO75-02)
† Consumer replaceable/removable parts


Flush Bottom
Overhang Bottom
CO75Pub600066R1 7/21/06 3:18 PM Page 4
Page: 3
7. Mark the 4 holes through the assembly onto the underside
of the cabinet with a pencil (D).
8. Remove the spacer mounting assembly.
9. Empty the contents from the bottom shelf. Be sure the
underside of the cabinet is free of grease or dirt.
10. Cover the countertop to catch wood chips from drilling.
Caution: Wear eye protection to prevent injury from shavings
when drilling.
11. Make a small starter hole by hammering a nail or using
a small drill bit.
12. Hold the 1/4" drill vertically at the hole marks and drill
up through the bottom of the cabinet.
13. Place a plastic washer on each screw with the flat side of the
washer resting on the cabinet shelf (E).
14. For a flat bottom cabinet:
a. Drop the screw through the drilled hole from inside the cabinet.
b. Repeat the procedure with the remaining screw and washer.
For cabinets with an overhang:
Push the proper number of spacer assemblies onto the screws coming through the
cabinet bottom.
15. Line up the 4 holes in the top of the can opener with the exposed screws beneath
the spacer assemblies and tightenthe screws into the top of the can opener.
16. Pull out the cord form the cord storage and plug into electric outlet.
Your unit is ready for use!
1. Lift the piercing lever.
2. Tip the can so that the rim is under the locating post, then push
down on the lever, making sure the cutter blade is inside the
rim (F).
Note: Because of the hands-free feature, it is not necessary to hold
the lever down or hold the can during cutting. However, you may
have to support very tall or heavy cans.
Tip: When the can is opened, the can opener will stop automatically.
3. To remove the can, hold it with one hand and raise the lever with the other.
Caution: Avoid contact with the cut edges of the can or lids — they are sharp. Carefully
discard the lid from the magnet.
1. For best results, sharpen the entire blade length in one
continuous stroke carefully pressing down on the blade as you
pull it through the slot (G).
2. Repeat for desired sharpness.
Important Tips:
• Use caution when washing and drying knives after sharpening.
• Do not sharpen serrated blades, as this will smooth their edges.
• Do not sharpen scissors.
1. Grasp the bottle.
2. Position the cap under the metal "hook" and pull sideways
to the right (H).
Important Tips:
• Do not use this can opener to open cans with a pull tab,
peel-off foil seal, or rolling key, rimless cans or cans with
angled corner.
• Open frozen juices or foods in cardboard cans right from the freezer. Aluminum lids
will not stick to the magnet.
Care and Cleaning
This product contains no user serviceable parts. Refer service to qualified service
Important: Unplug the cord before cleaning the unit.
1. Lift the piercing lever up as far as it will go.
2. Carefully grip the blade assembly and pull it away from the can
opener (J).
3. Wash in sudsy water by hand and dry thoroughly. Do not put
the blade assembly in the dishwasher.
4. Before replacing the blade assembly, wipe the can opener body,
knife sharpener (Models CO85 & CO85BM) and area around
the geared wheel with a slightly damp cloth or sponge.
1. Align key post on the blade assembly with key slot on the unit
2. Push in blade assembly and turn clockwise until it locks into
position (L).
CO75Pub600066R1 7/21/06 3:18 PM Page 6

Question & answers

There are no questions about the Black & Decker Spacemaker CO75 yet.

Ask a question about the Black & Decker Spacemaker CO75

Have a question about the Black & Decker Spacemaker CO75 but cannot find the answer in the user manual? Perhaps the users of can help you answer your question. By filling in the form below, your question will appear below the manual of the Black & Decker Spacemaker CO75. Please make sure that you describe your difficulty with the Black & Decker Spacemaker CO75 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.