Beko DV 7110 manual

View a manual of the Beko DV 7110 below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Beko
  • Product: Dryer
  • Model/name: DV 7110
  • Filetype: PDF
  • Available languages: Dutch, German, French, English, Danish

Table of Contents

Page: 30
31 EN
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed
through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for
future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
A	 Important safety information. Warning for hazardous situations with regard to life and
property.
B	 Caution; Warning for supply voltage.
	 Caution; Warning for fire hazard.
	 Caution; Warning for hot surfaces.
	 Read the instructions.
C	 Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment by
dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains
a great amount of recyclable material. It is marked with this label to indicate the used appliances
that should not be mixed with other waste. This way, the appliance recycling organised by your
manufacturer will be done under the best possible conditions, in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or
your retailer for the used appliance collection points closest to your home. We thank you doing
your part to protect the environment.
Page: 31
32 EN
1 Important safety information
This section includes safety information that
will help protection from risks of personal
injuries or materialistic damages. Failure
to follow these instructions shall cause
any warranty and reliability commitment to
become void.
General safety
•	 Never place the machine on a carpet-
covered floor, otherwise, lack of airflow
beneath the machine may cause electrical
parts to overheat. This will cause problems
with your machine.
•	 If the power cable or mains plug is
damaged, you must call Authorised Service
Agent for repair.
•	 The product should not be plugged in
during installation, maintenance and repair
works. Such works should always be made
by the technical service. Manufacturer
shall not be held responsible for damages
arising from processes carried out by
unauthorised persons.
•	 Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
•	 Operate your product at temperatures
between +5°C and +35°C.
•	 Do not use electrical devices in the
product.
•	 Do not connect the air exit of the product
to the chimney holes which are used for
the exhaust fumes of the devices operating
with gas or other types of fuel.
•	 You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
•	 Always clean the lint filter before or after
each loading.
•	 Never operate your dryer without the lint
filter installed.
•	 Do not allow fibre, dust and dirt
accumulation around the exhaust exit and
at adjacent areas.
•	 Power cable plug must be within easy
reach after installation.
•	 Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of
electric shock.
•	 Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket with
a suitable one.
•	 Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
•	 Do not dry items cleaned with industrial
chemicals in the dryer.
•	 Do not dry unwashed items in the dryer.
•	 Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
•	 Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
•	 Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
•	 This product must be grounded.
Grounding installation decreases the risk of
electric shock by opening a path with low
resistance for the electricity flow in case of
a malfunction or failure. Power cable of this
product is equipped with a conductor and
a grounding plug that allows for grounding
the product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with the
local laws and regulations.
•	 Do not install the product behind a door
with a lock, sliding door or a door that has
a hinge against the hinge of the dryer.
•	 Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
•	 Do not tamper with the controls.
•	 Do not perform any repair or part replacing
procedures on the product even if you
know or have the ability to perform unless
it is clearly suggested in the operating
instructions or the published service
manual.
•	 Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
•	 Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
Page: 32
33 EN
personnel.
•	 Do not reach into the machine when the
drum is spinning.
•	 Unplug the machine when it is not in use.
•	 Never wash down the appliance with
water! There is the risk of electric shock!
Always disconnect by unplugging from the
mains before cleaning.
•	 Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug only.
Do not operate the machine if the power
cable or plug is damaged!
•	 Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
•	 For malfunctions that cannot be solved by
following the information given in the safety
instructions:
	 Turn off the machine, turn off and contact
an authorised service agent.
•	 Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast in
order to lay them and dissipate the heat.
•	 Remove the door of the drying
compartment before decommissioning or
disposing of the product.
•	 The final step of the drying cycle (cool-
down cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
•	 Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
•	 Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
•	 Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
•	 At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Intended use
•	 This product has been designed for
domestic use. It should not be used for
other purposes.
•	 Use the product only for drying laundry that
are marked accordingly.
•	 Dry only those articles in your product that
are stated in this manual.
•	 This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
Children’s safety
•	 Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
•	 Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
•	 Do not allow children sit/climb on or enter
in the product.
•	 Children should be supervised to ensure
that they do not play with the product.
•	 Close the loading door when you leave the
area where the product is located.
Page: 33
34 EN
2 Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections must
be carried out by a qualified personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
•	 Install the product in an environment which
has no risk of freezing and is in a stable
and level position.
•	 Operate your product in a well ventilated,
dust-free environment.
•	 Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
•	 Do not place your product on a long pile
rug or on similar surfaces.
•	 Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
•	 Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
BDo not place the product on top of the
power cable.
•	 Keep at least 1.5 cm distance to walls of
other furniture.
Under counter installation
•	 A special part (Part no: 295 970 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under a
counter or in a cupboard. It should never
be operated without the top trim.
•	 Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or
in a cupboard.
Mounting over a washing machine
•	 A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no.
296 280 0100 white/296 280 0200 grey)
must be installed by the Authorised Service
Agent.
•	 Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Ventilation hose and connection (for
products equipped with an outlet
vent)
Ventilation hose allows exhaust air from inside
the machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can
be used instead of a hose. The pipe diameter
should be minimum 10 cm.
Maximum hose and pipe lengths are given in
the table below.
Hose Pipe
Maximum length 4 m 5 m
1 elbow 45° -1.0 m -0.3 m
1 elbow 90° -1.8 m -0.6 m
1 elbow 90° short -2.7 m
1 wall passage -2.0 m -2.0 m
CEach elbow and other passages should be
subtracted from the maximum length stated
above.
To connect a ventilation hose;
1.	 Connect the air outlet hose to the hose
spacer piece by turning it counterclockwise.
2.	 Make the hose passages as shown below.
CExhaust of humid air from the dryer into the
room is inconvenient. It may damage the
walls and furniture in the room.
CThe ventilation hose can be routed outdoors
via a window or it can be connected to the
air outlet in the bathroom.
CAir outlet hose must be routed directly to the
outdoors. There must be a limited number
of elbows as not to hinder ventilation.
CTo prevent water accumulation in the hose,
make sure that it is not folded on the floor.
Page: 34
35 EN
BThe ventilation hose should not be
connected to the chimney of a stove or a
fireplace.
BDo not operate your product at the same
time with heaters such as a coal or gas
stove. Airflow may cause the chimney to
flare up.
Adjusting feet
In order to ensure that your product operates
more silently and vibration-free, it must stand
level and balanced on its feet. Front feet of your
product can be adjusted. Balance the machine
by adjusting the feet.
1. Loosen the feet by hand.
2. Adjust the feet until the product stands level
and firmly on the floor.
C	Do not use any tools to loosen the
adjustable feet, otherwise, they can be
damaged.
C	Never remove the adjustable feet from their
housings.
C	You may supply 2 plastic pieces from an
Authorized Service with 2951620100 part
number. These parts prevent your machine
from slipping when the machine locates
on wet and slippery surfaces. You may
assemble mentioned parts to the front
adjustable feet by fitting and pressing them
to snap into ground of feet.
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table. Our
company shall not be liable for any damages
that will arise when the machine is used on a
circuit without grounding.
•	 Connection must comply with national
regulations.
•	 If the current value of the fuse or breaker
in the house is less than 16 Amps, have a
qualified electrician install a 16 Amp fuse.
•	 Power cable plug must be within easy
reach after installation.
•	 The voltage and allowed fuse or breaker
protection are specified in the “Technical
Specifications” section.
•	 The specified voltage must be equal to
your mains voltage.
•	 Do not make connections via extension
cables or multi-plugs.
• 	 The main fuse and switches must have a
contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is the
risk of electric shock!
First use
•	 To have the product ready for operation
before calling the authorised service agent,
make sure that its location and power
supply installations are appropriate. If they
are not, call a qualified electrician to have
any necessary arrangements carried out.
•	 Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of
this manual.
Disposing of packaging material
Packaging materials are dangerous to
children. Keep packaging materials in a safe
place out of reach of children. Packaging
materials of your product are manufactured
from recyclable materials. Sort and dispose
of them in accordance with recycled waste
instructions. Do not dispose of them with
normal domestic waste.
Transportation of the machine
1.	 Unplug the machine from the mains.
2.	 Remove the water drain (if any) and
chimney connections.
3.	 Drain water remained in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.
Page: 35
36 EN
EN 2
Height (adjustable) 85.0 cm
Width 59.5 cm
Depth 54 cm
Capacity (max.) 7 kg
Weight (net) 31 kg
Voltage
See type label
Rated power input
Model code
Type label is located behind the loading door.
Technical specification
Page: 36
37 EN
A B C
l m
n
o p q
D
Low
Laundry unsuitable for drying in
the machine
•	 Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
•	 Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
•	 Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
•	 Do not dry items made of hermetic
fibres such as pillows and quilts in the
dryer.
•	 Laundry made of foam or rubber will be
deformed.
•	 Do not dry laundry containing rubber in
the dryer.
•	 Do not dry laundry exposed to
petroleum, oil, combustible or explosive
agents in the dryer even if they are
washed beforehand.
•	 Overly wet laundry or laundry with
dripping water must not be put into the
dryer.
•	 Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should
not be dried in the product since they
emit flammable or explosive vapor.
Things to be done for energy
saving:
•	 Make sure that you operate the product
at its full capacity but pay attention to
not exceeding it.
•	 Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
•	 Pay attention to dry same types of
laundry together.
•	 Follow the instructions in the user
manual for programme selection.
•	 Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the
grill at the front side of the product.
•	 Do not open the door of the machine
during drying unless necessary. If you
must certainly open the door, pay
attention not to keep it open for a long
time.
•	 Do not add new (wet) laundry during
drying.
•	 Lint and fibres released from the laundry
to the air during the drying cycle are
collected in the “Lint Filter”. Make sure
that you clean the filters before or after
each drying.
•	 In models with condenser, make sure
that you clean the condenser regularly
at least once every month or after every
30 drying cycles.
•	 In vented models, follow the chimney
connection rules in the user manual and
pay attention to the chimney cleaning.
•	 Ventilate the room, where the dryer is
located, well during drying.
•	 For power saving in models with lamps, at
times when your dryer is not in use, keep
the door closed if the On/Off button is
pressed (if the dryer is energized).
Laundry suitable for drying in the
machine
C	 Always follow the suggestions on the
laundry labels. Dry only the laundry
having a label stating that they are
suitable for drying in a dryer and make
sure that you select the appropriate
programme.
3 Initial preparations for drying
Page: 37
38 EN
•	 Do not dry items cleaned with industrial
chemicals in the dryer.
•	 Do not dry your unwashed laundry in the
dryer.
•	 Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
•	 Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads should
not be dried in the dryer.
•	 Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
•	 Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Preparing laundry for drying
•	 Check all laundry items before loading
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on
any part of them.
•	 Fabric softeners and similar products
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
•	 All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
•	 Laundry may be tangled after washing.
Separate your laundry before placing
them into your dryer.
•	 Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
Correct load capacity
A	Consider the information in the
"Programme Selection Table". Always
start the programme in accordance with
the maximum load capacity.
C	 Adding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance
will degrade when the machine is
overloaded. Furthermore, your dryer
and your laundry can be damaged.
C	 Place your laundry into the drum loosely
so that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt
covers, large tablecloths) may bunch-
up. Stop the dryer 1-2 times during
drying process to separate bunched-up
laundry.
Following weights are given as examples.
Home articles
Approximate
weights (g)
Cotton quit covers (double) 1500
Cotton quit covers (single) 1000
Bed sheets (double) 500
Bed sheets (single) 350
Large tablecloths 700
Small tablecloths 250
Tea napkins 100
Bath towels 700
Hand towels 350
Garments Approximate
weights (g)
Blouses 150
Cotton shirts 300
Shirts 200
Cotton dresses 500
Dresses 350
Jeans 700
Handkerchiefs (10 pieces) 100
T-Shirts 125
Loading
•	 Open the loading door.
•	 Place laundry items loosely into the dryer.
•	 Push the loading door to close. Ensure
that no items are caught in the door.
Page: 38
39 EN
4 Selecting a Program and OperatingYour Machine
Control panel
1. Filter cleaning warning light
	 Warning light turns on when the filter is full.
2. Program follow-up indicator
	 Used to follow-up the progress of the
current programme.
3. Low temperature
	 Used to dry in low temperatures.
4. On/Off button
	 Used to turn on and off the machine.
5. Programme selection knob
	 Used to select a programme.
6. Start/Pause/Cancel button
	 Used to start, pause or cancel the
programme.
5
6
1 2 3 4
Cottons Synthetics Ventilation Ready
to iron
Ready to
wear
On/Off Start
pause
cancel
Filter
cleaning
Child-proof
lock
Tank
full
Spin
Low
temparature Timer
follow-up
indicator
Page: 39
40 EN
Preparing the machine
1.	 Plug in your machine.
2.	 Place the laundry in the machine.
3.	 Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme has
started. Press “Start/Pause/Cancel” button
of the machine to start the programme.
Timer program selection
Decide the appropriate time from the table
below which includes drying temperature in
degrees. Select the desired time with the timer
program selection button.
Extra dry Dry at high temperature
only for cotton laundry.
Thick and multi layered
laundry (E.g.: towels,
linens, jeans) are dried in
a way that they do not
require ironing before
placing in the wardrobe.
Ready to
Wear
Normal laundry (E.g.:
tablecloths, underwear)
are dried in a way that
they do not require
ironing before placing in
the drawers.
Ready to Iron Normal laundry (E.g.,
Shirts, dresses) are dried
ready to be ironed.
C For further program details, see, “Program/
Time Selection Table”
Main programs
•Anti-creasing
A 2-hour anti creasing program to prevent
laundry from creasing will be activated if you
do not take the laundry out after the program
has come to an end. This program rotates
the laundry in 60-second intervals to prevent
creasing.
•Ventilation
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your clothes
that have been kept at closed environments for
a long time thanks to this program to deodorize
unpleasant odors.
•Timer programs
You can select one of the 10 min...60 min...80
min... timer programs to achieve the final
drying level. Dry the cotton laundry at high
temperatures and synthetic and easy-care
laundry at low temperatures depending on the
type of the laundry.
C You must press the “Low temperature”
button for synthetics
Page: 40
41 EN
Program selection and consumption table
* : Energy Label standard program (EN 61121:2012)
All values given in the table have been fixed according to EN 61121:2012 Standard. These
values may deviate from the table according to the laundry type, laundry spin speed,
environmental conditions and voltage fluctuations.
EN 2
Program table
Programs
Capacity
(kg)
Spin speed in
washing machine
(rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
Cottons / Coloreds
A Ready to Wear
7
1000 % 60 130
800 % 70 150
3.5
1000 % 60 80-100
800 % 70 100-130
A Ready to Iron
7
1000 % 60 100
800 % 70 100-130
3.5
1000 % 60 60-80
800 % 70 80
Synthetics
B Ready to Wear
3.5
800 % 40 60
600 % 50 60-80
1.75
800 % 40 30-60
600 % 50 30-60
Delicates
B Ready to Wear 1.75 800 % 40 30
Energy consumption values
Programs
Capacity
(kg)
Spin speed in
washing machine
(rpm)
Approximate
amount of
remaining
humidity
Energy
consumption
value kWh
Cottons linen Ready to wear* 7 1000 % 60 4.20
Cottons Ready to iron 7 1000 % 60 3.10
Synthetics Ready to wear 3.5 800 % 40 1.30
Page: 41
42 EN
to switch the machine to “Pause” mode.
Drying process will stop.
2. Open the door at Pause position and close
it again after adding or taking out laundry.
3. Press “Start/Pause/Cancel” button to start
the program.
C Any laundry added after the drying process
was started may cause the already dried
clothes in the machine intermingle with wet
clothes and the result will be wet laundry
after the drying process is over.
C Laundry may be added or taken out as
much as desired during a drying process,
but as this process will interrupt drying
continuously, it will extend the program
duration and increase energy consumption.
Therefore, it is recommended to add
laundry before the drying program is
started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of
keys while the program is on. The loading
door and all keys except the “On/Off” key on
the panel are deactivated when the child-proof
lock is active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Low
temperature” buttons simultaneously for 3
seconds.
To start a new program after the program is
over or to interrupt the program, the childproof
lock should be deactivated. To deactivate the
childproof lock, press the same buttons for 3
sec.
C One of the LEDs on the program follow-up
indicator starts flashing when the child-
proof lock is activated.
CChild-proof lock is deactivated when the
machine is restarted by pressing the On/
Off button.
Ending the program through
canceling
The program which is selected first will keep
on going even if the position of the program
selection button is changed. A new program
can be selected and started after “Program
cancel” is activated in order to change the
drying program.
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
Warning LED will light up when you select the
function.
C You must use this function when you dry
your synthetic or delicate laundry.
Warning indicators
C Warning indicators may differ according to
the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C If the filter cleaning warning LED lights up
continuously, please refer to, “Solution
suggestions for problems”.
Starting the Program
1.	 Press “Start/Pause/Cancel” button to start
the program.
2.	 “Start/Pause/Cancel” button will light up to
indicate that the program has started.
Timer follow-up indicator
One of the lamps is on as far as program runs
and shows the approximate remaining time.
C LEDs on the timer follow-up indicator will
also flash when the child-proof lock is
activated.
A If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the program after the program
has started
You can use this feature to dry your laundry
in a different program after your machine has
started to run.
For example;
Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to select “80”
minutes program instead of “60” minutes
program.
Select the “80” minutes program by rotating
the program knob.
Press “Start/Pause/Cancel” button to start the
program.
C The program which is selected first will go
on even if the program selection button
is moved and another program mode is
selected while the machine is operating.
You must cancel the ongoing program in
order to change the drying program. (See,
Ending the program through canceling)
Adding/removing laundry in standby mode
In order to add or take out laundry after the
start-up of the program;
1. Press the “Start/Pause/Cancel” button
Page: 42
43 EN
To cancel any selected program;
•	 Press “Start/Pause/Cancel” button for about
a duration of 3 seconds. The “Filter cleaning”
and “Water tank” warning LEDs as well as
the “0” warning LED on the program follow-
up indicator will light up at the end of this
period for reminding purposes.
A As the inside of the machine will be
excessively hot when you cancel the
program while the machine is running,
activate the ventilation program to cool it
down.
A If the machine is stopped during any drying
program, and if the position of the program
selection knob is changed, an audio signal
will be heard (if the “Cancel audio warning”
function is not selected).
The machine will not start even if the “Start/
Pause/Cancel” button is pressed, unless the
program selection knob is returned to the
initial program. The paused program must
be cancelled in order to change the drying
program.
End of program
The “Filter cleaning” and “Water tank” warning
LEDs as well as the “0” warning LED on the
program follow-up indicator will light up at the
end of the program. The door can be opened
and the machine becomes ready for a second
cycle.
Press the “On/Off” button to shut down the
machine.
C A 2-hour anti creasing program to prevent
laundry from creasing will be activated if you
do not take the laundry out after the program
has come to an end.
C Clean the filter after each drying (please see,
Filter cleaning).
C Drain the water tank after each drying (please
see, Water tank)
Page: 43
44 EN
5 Maintenance and cleaning
Cover filter
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Cover Filter”.
CSuch fibre and lint are generally formed during
wearing and washing.
CAlways clean the filter after each drying
process.
CYou can clean the filter and filter area by
vacuum cleaner.
Figure 1
Figure 2
To clean the filter:
1.Take out the cover.
2.a) If the product’s cover filter can be opened
as shown in Figure 1, remove the filter by
pulling it up and open the filter.
2.b) If the product’s cover filter is as shown in
Figure 2, remove the filter by pulling it up.
3. Clean lint, fibre, and cotton raveling on the
filter and in the filter housing by hand or with
a soft piece of cloth.
4. Close the filter and place it back into its seat.
CClogging may arise on the filter surface after
using your machine for some time; if this
occurs, wash the filter with water and dry it
before using again.
Page: 44
45 EN
6 Solution suggestions for problems
Problem Cause Explanation / Suggestion
Drying process
takes too much
time.
Cover filter and filter drawer might
have not been cleaned.
* Meshes of the filter may be clogged.Wash
with water.
Laundry come out
wet at the end of
drying.
* Cover filter and filter drawer might
have not been cleaned.
* Excessive laundry might have been
loaded in.
* Meshes of the filter may be clogged.Wash
with water.
* Do not overload the machine.
Machine does not
switch on or the
programme does
not start. Machine
is not activated
when set.
* It might have not been plugged in.
* The loading door may be ajar.
* Programme might have not been set
or the «Start/Pause/Cancel» button
might have not been pressed.
* «Childproof lock» might have been
activated.
* The condenser cover on the models
with a condenser might not be closed
securely.
* Make sure that the machine is plugged in.
* Make sure that the loading door is
properly closed.
* Make sure that the programme has been
set and it is not in “Pause” mode.
* Deactivate the childproof lock.
* Make sure that the condenser cover and
the red lock is closed securely.
Programme has
been interrupted
without any cause.
* The loading door may be ajar.
* Electricity may be cut off.
* Make sure that the loading door is
properly closed.
* Press «Start/Pause/Cancel» button to
start the programme.
Laundry has
shrunk, become
felted or
deteriorated.
* A programme suitable for the laundry
type might have not been used.
* Dry only the laundry which is suitable for
drying in your machine after checking the
labels on your clothes.
* Select a programme with suitable low
temperature for the laundry type to dry your
clothes.
Drum lightning
does not come on.
(for models
equipped with a
lamp)
* The machine might have not been
started by using the On/Off button.
* Bulb may have blown.
* Make sure that the machine is On.
* Call the authorized service to replace the
bulb.
“Final / Anti-
creasing” LED
flashes.
* The 2-hour anti creasing programme
to prevent laundry from creasing might
have been activated.
* Turn off the machine and take out the
laundry.
“Final / Anti-
creasing” LED is
on.
* Program has come to an end.
* Turn off the machine and take out the
laundry.
The “Drying” LED
flashes.
* A heat sensor failure has occurred.
Machine ends the programme without
heating.
* Turn off the machine and take out the
laundry. Call your authorized service.
“Filter cleaning”
LED flashes.
* Filter might have not been cleaned. * Clean the cover filter.
Also for products equipped with a condenser
“Water tank”
warning LED is on.
* Water may be full.
* Anti-creasing programme might be
running.
* Drain the water in the water tank.
“Condenser
cleaning” LED is
on.
* Filter drawer/Condenser might have
not been cleaned.
* Clean the filters in the condenser/filter
drawer under the kick plate.
A Call an authorized service agent if the problem persists.

Question & answers

There are no questions about the Beko DV 7110 yet.

Ask a question about the Beko DV 7110

Have a question about the Beko DV 7110 but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Beko DV 7110. Please make sure that you describe your difficulty with the Beko DV 7110 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.