Beko BITA 60 I manual

View a manual of the Beko BITA 60 I below. All manuals on can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Beko
  • Product: Exhaust hood
  • Model/name: BITA 60 I
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Portuguese

Table of Contents

Page: 17
- 18 -
as the cooker hood removes the air from the environment
which a burner or fireplace need for combustion.The negative
Provide adequate ventilation in the environment for a safe
operation of the cooker hood. Follow the local laws applicable
for external air evacuation.
Before connecting the model to the electricity network:
Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to the
network and the socket is suitable. If in doubt ask a qualified
-	Ifthepowersupplycableisdamaged,itmustbereplacedwith
another cable or a special assembly, which may be obtained
direct from the manufacturer or from theTechnical Assistance
-	Thisdevicemustbeconnectedtothesupplynetworkthrough
either a plug fused 3A or hardwired to a 2 fase spur protected
by 3A fuse.
2.		Warning!
In certain circumstances electrical appliances may be a
danger hazard.
A)		Do not check the status of the filters while the cooker
hood is operating.
B)		Donottouchbulbsoradjacentareas,duringorstraight
after prolonged use of the lighting installation.
C)		Flambè cooking is prohibited underneath the cooker
D)		Avoid free flame, as it is damaging for the filters and a
fire hazard.
E)		Constantly check food frying to avoid that the
overheated oil may become a fire hazard.
F)		Disconnecttheelectricalplugpriortoanymaintenance.
G)		Thisapplianceisnotintendedforusebyyoungchildren
or infirm persons without supervision.
H)		Youngchildrenshouldbesupervisedtoensuretheydo
not play with the appliance.
I)			There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels.
L)		There is a risk of fire if cleaning is not carried out in
accordance with the instructions.
Waste Electrical and Electronic Equipment (WEEE). By making
sure that this appliance is disposed of in a suitable manner,
the user is helping to prevent potential damage to the
environment or to public health.
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not be
treated as domestic waste, but should be delivered to
point. Follow local guidelines when disposing of waste. For
more information on the treatment, re-use and recycling of
this product, please contact your local authority, domestic
waste collection service or the shop where the appliance was
•		Assemblyandelectricalconnectionsmustbecarriedout
by specialised personnel.
•		Wear protective gloves before proceeding with the
•		Electric Connection:
Note! Verify the data label placed inside the appliance:
-	If the symbol appears on the plate, it means that no earth
connection must be made on the appliance, therefore follow
the instructions concerning insulation class II.
-	If the symbol DOES NOT appear on the plate, follow the
instructions concerning insulation class I.
Insulation class II
-	The appliance has been manufactured as a class II, therefore
no earth cable is necessary.The plug must be easily accessible
after the installation of the appliance. If the appliance
is equipped with power cord without plug, a suitably
dimensioned omnipolar switch with 3 mm minimum opening
between contacts must be fitted between the appliance and
the electricity supply in compliance with the load and current
-	The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral.
Insulation class I
This is a class I, appliance and must therefore be connected to
an effiecient earthing system.
-	The appliance must be connected to the electricity supply as
BROWN = L line
BLUE = N neutral
The neutral wire must be connected to the terminal with the
to the terminal by the earth symbol .
the ducted cooker hood, make sure that the electrical plug is
in a position where it can be accessed easily. If the appliance
is connected directly to the electricity supply, an omnipolar
switch with a minimum contact opening of 3 mm must be
placed in between the two; its size must be suitable for the
load required and it must comply with current legislation.
•		Ifthehobiselectric,gas,orinduction,theminimumdistance
between the same and the lower part of the hood must be at
least 65 cm. If a connection tube composed of two parts is
not connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from other
proceeding with the assembly operations, remove the anti-
grease filter(s) (Fig.7A) so that the unit is easier to handle.
-		Inthecaseofassemblyoftheapplianceinthesuctionversion
prepare the hole for evacuation of the air.
•		We recommend the use of an air exhaust tube which has the
same diameter as the air exhaust outlet hole. If a pipe with a
smaller diameter is used, the efficiency of the product may be
reduced and its operation may become noisier.
•		Fixing to the wall:
-	Drill the holes A respecting the distances indicated (Fig.2).
-	Fix the appliance to the wall and align it in horizontal position
to the wall units.
-	Whentheappliancehasbeenadjusted,definitelyfixthehood
using the screws A (Fig.5).
For the various installations use screws and screw anchors
etc.). If the screws and screw anchors are provided with the
Page: 18
- 19 -
product, check that they are suitable for the type of wall on
which the hood is to be fixed.
•		Fixing the decorative telescopic flue:
-	Arrange the electrical power supply within the dimensions
of the decorative flue. If your appliance is to be installed in the
ducting version or in the version with external motor, prepare
the air exhaust opening.
Adjust the width of the support bracket of the upper flue
-	Then fix it to the ceiling using the screws A (Fig.3) in such a
from the ceiling indicated in Fig.2.
Connect the flange C to the air exhaust hole using a
connection pipe (Fig.5).
-	Insert the upper flue into the lower flue.
-	Fix the lower flue to the hood using the screws B provided
(Fig.5), extract the upper flue up to the bracket and fix it with
the screws B (Fig.3).
-	If your appliance has the lower connections indicated as in
Fig.4A, the fixing to be carried out is that shown in Fig.6A.
To transform the hood from a ducting version into a filtering
version, ask your dealer for the charcoal filters and follow the
installation instructions.
•		Filter hood:
Please note:
-	In order to transform the hood from EXTRACTORHOOD into
distributor as accessory.
We have two different types of Kit, one with non-regenerable
active carbon filters (Fig.7B) and the other one with
regenerable active charcoal filters (washable) (Fig.7C).
-	To replace the non-regenerable active carbon filters X, pull
lever outwards as shown in Fig.7B.
•		We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air. The effective
performance of the cooker hood depends on constant
maintenance; the anti-grease filter and the active carbon filter
both require special attention.
•		The anti-grease filter is responsible retaining the grease
with variable frequency according to the use of the appliance.
-		To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
-		After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
•		The active carbon filters are used to purify the air that is
sent back into the room and its function is to mitigate the
unpleasant odours produced by cooking.
-		The non-regenerable active carbon filters must be replaced
at least every 4 months. The saturation of the active charcoal
depends on the more or less prolonged use of the appliance,
on the type of kitchen and on the frequency with which anti-
grease filter is cleaned.
-		Regenerable active charcoal filters must be washed by hand,
with non abrasive neutral detergents, or in the dishwasher at
a maximum temperature of 65°C (the washing cycle must be
complete without dishware). Remove excess water without
damaging the filter, remove the plastic parts, and let the
mat dry in the oven for at least 15 minutes approximately at
a maximum temperature of 100°C. To keep the regenerable
charcoal filter functioning efficient this operation must be
repeated every 2 months. These must be replaced at least
every 3 years or when the mat is damaged.
•		Before remounting the anti-grease filters and the
are completely dry.
•		Cleanthehoodfrequently,bothinternallyandexternally,
liquid detergents that are non abrasive.
•		The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room. The
prolonged use of the lighting system significantly decreases
the average duration of the bulbs.
•		If the appliance is equipped with courtesy lights it is possible
to use them for general room lighting for a prolonged amount
of time.
•		Attention: the non compliance with the hood cleaning
warnings and with the replacement and cleaning of the filters
entails risk of fires. One therefore recommends keeping to the
suggested instructions.
•		Replacing halogen light bulbs (Fig.8):
In order to replace the dichroic lamps, carefully remove
the lamp from the lamp holder with the help of a small flat
screwdriver or a similar tool. PLEASE NOTE! In doing this
the bulbs with new ones of the same type.
•		Replacing halogen light bulbs (Fig.9):
To replace the halogen light bulbs B, remove the glass pane
with new ones of the same type. Caution: do not touch the
light bulb with bare hands.
•		Replacing LED lamps (Fig.10):
If the appliance version is with LED lamps, the intervention of
a specialised technician is necessary to replace them.
•		Replacing the halogen/incandescent lamps (Fig.11):
Only use lamps of the same type and Wattage installed on
the device.
•		Commands luminous (Fig.12.A.B.) the key symbols are
explained below:
F		= AUTOMATIC STOP TIMER - 15 minutes (*)
If your appliance has the INTENSIVE speed function, from
speedTHREE, press key E for 2 seconds and it will be activated
for 10 minutes after which it will return to the previously
set speed. When the function is active the LED flashes. To
interrupt it before the 10 minutes have elapsed, press key E
again. Some models allow activating this function even with
speed one and two.
the“cleanair”function is activated.This function switches the
appliance on for ten minutes every hour at the first speed. As
soon as this function is activated the motor starts up at the
first speed for ten minutes. During this time key F and key
C must flash at the same time. After ten minutes the motor
switches off and the LED of key F remains switched on with
a fixed light until the motor starts up again at the first speed
Page: 19
- 20 -
after fifty minutes and keys F and C start to flash again for ten
minutes and so on. By pressing any key for the exclusion of
the hood light the hood will return immediately to its normal
functioning (e.g. if key D is pressed the“clean air”function is
deactivated and the motor moves to the 2nd speed straight
away. By pressing key B the function is deactivated).
(*) The “automatic stop timer” delays stopping of the
hood, which will continue functioning for 15 minutes at the
operating speed set at the time this function is activated.
•		Anti-grease/active charcoal filters saturation:
-	When the A key flashes with a 2 second frequency the anti-
grease filters must be washed.
-	When the A key flashes with a 0.5 second frequency the
active carbon filters must be replaced or washed depending
on the type of filter.
Once the clean filter has been put back one must reset the
electronic memory by pressing the A key for approximately 5
seconds until it stops flashing.
•		Commands mechanical (Fig.13.A.B.C.) the key symbols are
explained below:
G	= MOTOR WORKING indicator.
•		Commands (Fig.14):
Push-button A = On/off lights switch.
Push-button B = On/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off.
Decreases the motor speed.
Display C = Indicates the motor speed level selected and
activates the timer.
Push-button D = Switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10’, then the appliance go back to work at
the original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer is
deactivated by re-pressing Key E.
When the Timer is activated the decimal point must flash on
the display. The Timer cannot be activated if the intensive
speed is functioning.
The “clean air” function is activated by pressing key E for 2
seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter“C”must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning. Press key
E to deactivate the function.
•		Anti-grease/active charcoal filters saturation:
-	When display item C flashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the anti-grease filters must be
-	When display item C flashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the active carbon filters must
be replaced or washed depending on the type of filter.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops flashing.
•		Mechanical controls (Fig.15) the symbols are as follows:
If the hood is shut off at first, second or third speed, when
it is turned back on, it will start at the same speed it was in
when switched off.
belangrijke aanwijzingen voor een veilige installatie, gebruik
en onderhoud. Bewaar de handleiding om die later te kunnen
raadplegen. Het toestel werd ontworpen in een versie voor
afzuiging (evacuatie van de lucht naar buiten - Afb.1B) en
voor filtering (recirculatie van de lucht binnen - Afb.1A) of met
externe motor (Afb.1C).
1.	Opletten indien tegelijkertijd een afzuigkap en een
brander of haard functioneren die afhankelijk zijn van
de omgevingslucht en gevoed worden door een andere
energiebron dan de elektrische energie. De afzuigkap kan de
aan de omgeving onttrekken. De negatieve druk in de
omgeving mag niet boven de 4 Pa (4x10-5 bar) liggen. Voor
van de ruimte.Voor de afvoer naar buiten moet u zich houden
aan de geldende voorschriften die van toepassing zijn in uw
Voordat u het model op het elektriciteitsnet aansluit:
-	Controleer op het gegevensplaatje (aan de binnenkant van
met die van het net, en of de stekker geschikt is voor de
aansluiting. Neem in geval van twijfel contact op met een
gekwalificeerde elektricien.
Als de voedingskabel beschadigd is dient deze te
worden vervangen door een andere kabel of een speciale
-	Verbind het mechanisme aan de voeding m.b.v. en stekker
met zekering 3A of aan de twee draden van de tweefase
beschermd met een 3A zekering.
2.		Attentie!
In bepaalde omstandigheden kunnen huishoudelijke
apparaten gevaarlijk zijn.
A)		Probeer niet om de filters te controleren terwijl de
afzuigkap werkt.
Raak de lampen en de zones vlakbij niet aan als de

Question & answers

There are no questions about the Beko BITA 60 I yet.

Ask a question about the Beko BITA 60 I

Have a question about the Beko BITA 60 I but cannot find the answer in the user manual? Perhaps the users of can help you answer your question. By filling in the form below, your question will appear below the manual of the Beko BITA 60 I. Please make sure that you describe your difficulty with the Beko BITA 60 I as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.