Ariston Thermo ASL70C manual

View a manual of the Ariston Thermo ASL70C below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: Ariston Thermo
  • Product: Dryer
  • Model/name: ASL70C
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Portuguese

Table of Contents

Page: 0
Contents
TUMBLE DRYER
ASL70C
Instruction booklet
Installation, 2-3
Door reversal instructions
Where to put your dryer
Ventilation
Water drain
Electrical connection
Before you start using your dryer
Dryer description, 4
To open the door
The features
Control panel
Start and programmes, 5-6
Choosing a programme
Table of programmes
The controls
Laundry, 7-8
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 9
General safety
Disposal
Saving energy and respecting the environment
Maintenance and Care, 10
Switching off the electricity
Cleaning the filter after each cycle
Empty the water container after each cycle
Check the drum after each cycle
Cleaning the condenser unit
Cleaning the dryer
Troubleshooting, 11
Service, 12
Spare parts
GB
English, 1
I
Italiano, 13
F
Français, 25
D
Deutsch, 37
E
Español, 49
NL
Nederlands, 73
P
Português, 61
GB
1
Page: 1
Installation
2
GB
! Keep this instruction booklet on hand in order to refer to
it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another
party, make sure that this booklet is supplied along
with the dryer so that the new owner may be informed
about warnings and suggestions on how the dryer
works.
! Read these instructions carefully; the following
pages contain important information on installation
and suggestions on how the appliance works.
Door Reversal Instructions
The door of your dryer is reversible and can easily be
changed. Exchange diagonally hinge brackets and
blanking screws. Exchange door latch and catch with
their opposite blanking plates (see diagram above).
Where to put your dryer
● Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
● If you are going to install the appliance under a
work counter, be sure to leave a 10mm space
between the top and any other objects on or
above the machine and a 15mm space between the
sides and lateral furnishings or walls. This is to ensure
proper air circulation. Make sure that the back vents
are not obstructed.
Ventilation
When the dryer is in use, there has to be adequate
ventilation. Make sure you put your dryer in an
environment that is not damp and has proper air
circulation throughout. Airflow around the dryer is
essential to condense the water produced during the
washing, the dryer will not operate efficiently in an
enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation could be experienced.
Door catch
Door latch
Hinge
Hinge
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. Simply remove the top hose
from its top fitting at the rear of the dryer and plumb the
hose provided to the drain.
Electrical connections
Make sure of the following before you insert the plug
into the the electrical socket:
● The socket must be grounded.
● The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
● Power voltage must be within the values indicated
on the rating label (see Dryer Description).
● The socket must be compatible with the dryers plug.
Should this not be the case, replace the plug or the
socket.
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied should be checked
periodically and replaced by a cord specially prepared
for this dryer and fitted only be authorised technicians
(see Service). New or longer power cords are supplied
at an extra charge by authorised dealers.
! The manufacturer denies any responsibility should any
of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
Page: 2
Installation
Description
Start
and
Programmes
Laundry
Warnings
and
Suggestions
Maintenance
and
Care
Troubleshooting
Service
GB
3
replacing the empty water container, the dryer must be
running for this to happen (see The Controls).
The On/Off indicator light signals that your dryer
is in use or ready to select a programme. If this light
flashes it indicates there is a fault (see Troubleshooting).
The ON/OFF button : If the dryer is running and
this button is pressed, the dryer stops. Press again,
the dryer restarts.
The Progress or Delay lights show you the status of
the programme, or the delay time when they flash.
During a delayed start the lights flash to show the
delay selected. When (not flashing) they show each
stage of the programme by the corresponding light
turning on (see Start and Programmes).
The PROGRAMMES knob sets the programme:
rotate it until the indicator is pointing to the programme
you want to select (see Start and Programmes).
The START/CANCEL button starts a selected
programme. When you press this button there will be
one beep and the progress lights will flash to confirm
the action. If you have not set a programme, the buzzer
will beep four times. When a programme is running,
holding this button cancels the programme and stops
the dryer (see Start and Programmes).
The OPTION buttons select available options for your
selected programme (see Start and Programmes).
The Option lights indicate that the option has been
selected by the button to the left of the appropriate
light.
The Drying Guide allows you to consult a user friendly
table of fabric types and load capacities.
The Empty Water indicator light signals that the
water container should be emptied. When it is flashing
it indicates that the container is full.
The light will take a few seconds to go out after
Control panel
Dryer Description
Empty Water
Light
Drying Guide
PROGRAMMES
Knob
START/CANCEL
Button
Indicator
Progress or Delay
Lights
OPTION
Buttons
Option
Lights
On/Off
Light
ON/OFF
Button
To open the door The features
Press and release the front
panel in position shown
Water container
Air intake
grille
Rating plate
Door catch
Filter
Door latch Model &
Serial
numbers
Condenser cover handle
(Pull to open)
Condenser cover
Page: 3
4
GB
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place and the water container is empty
and in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the On/Off light is not lit: Press the ON/OFF
button .
6. Choose a programme by checking the Programmes
Guide (see Programmes) as well as the indications
for each type of fabric (see Laundry).
- Select a programme by rotating the
PROGRAMMES knob.
7. Set a delay time and other options if necessary.
8. If you wish to select the buzzer sound, at the end
of the progamme, press the ALARM Option button.
9. Press the START button to begin.
During the drying programme, you can check on
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START button in order
to resume drying.
10. During the last few minutes of Drying
Programmes, before the programme is
completed, the final COOL TUMBLE phase is
entered (fabrics are cooled), this phase should
always be allowed to complete.
11. When the programme is complete. The buzzer
will sound if Alarm option was selected.
Open the door, take the laundry out, clean the filter
and replace it. Empty the water container and
replace it (see Maintenance).
If the Post Creasecare option has been selected
and you do not remove the laundry immediately,
the dryer will tumble occasionally for 10 hours or
until you open the door.
12. Unplug the dryer.
Start and Programmes
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The
cycle relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric Maximum load
Cotton and Cotton mixtures 2.5kg
Synthetics 2kg
Denim 2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton
mix, and less well on acrylic fibres and on materials such as Tencel®.
Page: 4
Installation
Description
Start
and
Programmes
Laundry
Warnings
and
Suggestions
Maintenance
and
Care
Troubleshooting
Service
GB
5
Programmes
Programme What it does... How to set it... Note:
Easy
Iron
Brief programme (approximately
10 minutes) that softens fibres of
clothing that is ready for ironing.
! This is not a drying
programme (see previous
page).
Options available:
Alarm
1. Position the PROGRAMMES knob
on .
2. Select any options if required.
3. Press the START button.
Options available:
Alarm
1. Position the PROGRAMMES knob
on .
2. Select any options if required.
3. Press the START button.
Options available:
Alarm, Delayed Start,
Pre-Creasecare,
Post Creasecare.
1. Position the PROGRAMMES knob
on .
2. Select any options if required.
3. Press the START button.
Options available:
Alarm, Delayed Start,
Pre-Creasecare,
Post Creasecare.
1. Position the PROGRAMMES knob
on .
2. Select any options if required.
3. Press the START button.
Options available:
Alarm, High Heat, Delayed
Start, Pre-Creasecare,
Post Creasecare.
Consult ‘suggested drying
times’ (see Laundry).
The last 10 minutes of these
programmes is the Cool
Tumble phase, see below.
1. Position the PROGRAMMES knob
on the desired time: 160, 140, 120,
100, 80, 70, 60, 50, 40, 30 or 20.
2. Select any options if required.
3. Press the START button.
Cottons
Cupboard
dry
Dries your clothes on High Heat
setting, ready for putting away.
Timed Drying
(160, 140, 120,
100, 80, 70, 60,
50, 40, 30 or 20
minutes)
Dries wet clothing that you wish
to dry on Low Heat or small
loads (less than 1kg).
Can be used with High Heat
option if you prefer to use a
timed programme.
Brief programme (approximately
10 minutes) that cools fibres of
clothing.
Synthetics
Cupboard
dry
Cool Tumble
Dries your clothes on Low Heat
setting, ready for putting away.
Start and Programmes
! If the On/Off light is not lit; Press the ON/OFF button and then select programme.
Page: 5
6
GB
Alarm
Available on all programmes and allows the buzzer to
give a signal at the end of the drying cycle, to remind
you that the clothes are ready to be removed.
Press the button and the light will show that the option
is selected.
Post Creasecare
The clothes are occasionally tumbled after the end of
the drying and cool tumble cycles, to help prevent
creases developing should you not be available to
remove the load immediately the programme is complete.
Empty Water Light / Container
(If you have plumbed your dryer to a drain this light
can be ignored, as there is no need to empty the water
container).
When this light is on (not flashing) it reminds you to
empty the water container.
If the water container fills during a programme, the
heater turns off and the dryer does a period of Cool
Tumble then the light flashes and the buzzer sounds.
After this it stops and all 3 progress lights and the 3hr
delay light come on and the empty water light flashes.
You must empty the water container and restart the
dryer or the clothes will not dry. After re-starting the
dryer, the light will take a few seconds to go out.
To avoid this always empty the water container each
time you use the dryer (see Maintenance).
● Door Opening
Opening the door during a programme will stop the
dryer and have the following effects:
● All 3 progress lights and the 3hr delay light come on.
● During a delay phase the delay will continue to
count down. The start button must be pressed to
resume the delay programme.
One of the delay lights will flash to show the
current delay setting.
● The start button must be pressed to resume the
programme. The progress lights will change to
show the current status.
● During the cool tumble or post creasecare phase
of a drying programme and anytime during an
Airing or Cool Tumble programme, the
programme will finish. Pressing the start button
will re-start a new programme at the beginning.
● Changing the programmes knob will select a new
programme, after you press the start button. You
can use this to select the Cool Tumble
programme to cool the clothes, if you find them
dry enough.
● Note
If you have a power cut, switch off the power or
remove the plug, press the START button and the
programme will resume.
● PROGRAMMES knob
! Warning, if after pressing the start button, the
programmes knob position has changed, the new
position will NOT change the programme selected.
! Position 0, turning the knob to position 0 resets and
cancels a programme.
● OPTION buttons / lights
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected on the programmes knob before
an option can be selected. Not all options are available
for all programmes (see Start and Programmes). If an
option is not available and you press the button, the
buzzer will beep four times. If the option is available
there will be one beep and the option light next to the
button lights to confirm the selection.
Progress ( Drying, Cool Tumble, Post
Creasecare) / Delay (3hr, 6hr, 9hr, 12hr) Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time is selected. During other
programmes they indicate the progress of the dryer,
each one comes on as the corresponding phase starts.
Time Delay
The start of some programmes (see Start and
Programmes) can be delayed for up to 12 hours in 3hr
steps. Ensure the water bottle is emptied before setting
a delayed start.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period
light will flash (after the start button has been pressed).
To set a delayed start, press the Time Delay button,
and the light next to the button will come on together
with the 3hr delay light. Pressing the button again will
advance the delay setting to 6hr, the 3hr light goes
out and the 6hr light is on. Each time you press the
button the delay setting advances 3 hours, as indicated
by the corresponding light. If the 12hr light is on,
pressing the button again will cancel the delay.
You can also cancel the delay by turning the programmes
knob to 0, wait for the buzzer to beep and then turn
back to your selected programme.
Pre Creasecare
When a delayed start has been selected the clothes
are tumbled occasionally during the delayed period to
help prevent creases developing.
High Heat
When available this button selects high heat. Press this
button and a high heat setting is selected and the light
alongside the button comes on. Timed programmes
have a default of low heat, if the light alongside the
button is on then pressing the button selects a low heat
setting and the light goes out.
The Controls
Start and Programmes
Page: 6
Laundry
Installation
Description
Start
and
Programmes
Laundry
Warnings
and
Suggestions
Maintenance
and
Care
Troubleshooting
Service
GB
7
Sorting your laundry
● Check symbols on clothing labels to make sure
that the articles can be tumble dried.
● Sort laundry by fabric type.
● Empty pockets and check buttons.
● Close zippers and hooks and tie loose belts and
strings.
● Wring out each item in order to eliminate as much
excess water as possible.
! Do not load dripping wet clothes into the dryer.
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 7kg max (15lb)
Synthetic fibres: 3kg max (6.6lb)
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical load
Clothes
Blouse Cotton 150g 5oz
Other 100g 3oz
Dress Cotton 500g 1lb 2oz
Other 350g 12oz
Jeans 700g 1lb 6oz
10 nappies 1000g 2lb 3oz
Shirt Cotton 300g 10oz
Other 200g 7oz
T-Shirt 125g 4oz
Household Items
Duvet cover Cotton 1500g 3lb 5oz
(Double) Other 1000g 2lb3oz
Large Tablecloth 700g 1lb 6oz
Small Tablecloth 250g 9oz
Tea Towel 100g 3oz
Bath Towel 700g 1lb 6oz
Hand Towel 350g 12oz
Double Sheet 500g 1lb 2oz
Single Sheet 350g 12oz
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
Wash Care Labels
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
May be tumble dried
Do not tumble dry
Tumble dry at high heat setting
Tumble dry at low heat setting
Items not suitable for tumble drying
● Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
● Glass fibres (certain types of draperies)
● Items which have been dry cleaned
● Items with the ITCL Code (see Special
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
● Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Page: 7
8
GB
Laundry
Special clothing items
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Drying times
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
Cottons
High (full) Heat
Drying times 800-1000rpm in washing machine
Half Load Full Load
1kg 2kg 3kg 4kg 5kg 6kg 7kg
30-40 40-55 55-70 70-80 80-90 95-120120-140
Synthetics
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load Full Load
1kg 2kg 3kg
40-50 50-70 70-90
Acrylics
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load Full Load
1kg 2kg
40-60 55-75
Times are approximate and can vary depending
upon:
● Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
● Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
● Quantity of laundry: single items or small loads
may take longer to dry.
● Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
● Heat setting.
● Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
● Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Page: 8
! The appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons and
must be read carefully.
This appliance conforms to the following
EEC Directives:
- 72/23/EEC and 93/68/EEC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC
(Electromagnetic Compatibility)
General safety
● This tumble dryer has been designed for home,
and not professional use.
● This dryer must be used by adults, and the
instructions in this booklet should be followed carefully.
● Do not touch the appliance while barefoot or with
wet hands or feet.
● Unplug the machine by pulling on the plug, not
the cord.
● Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
● The appliance must be installed correctly and
have proper ventilation. The air intake at the front
of the dryer and rear vent behind the dryer should
never be obstructed (see Installation).
● Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
● Check to see if the dryer is empty before loading it.
● The back of the dryer could become very
hot. Never touch it while in use.
● Do not use the dryer unless the filter, water
container and condenser are securely in place
(see Maintenance).
● Do not use fabric softeners or dryer sheets in the
dryer.
● Do not overload the dryer (see Laundry for
maximum loads).
● Do not load items that are dripping wet.
● Tumble dry items only if they have been washed
with detergent and water, rinsed and been through
the spin cycle. It is a fire hazard to dry items that
HAVE NOT been washed with water.
● Carefully check all instructions on clothing labels
(see Laundry).
● Do not dry garments that have been treated with
chemical products.
Installation
Description
Start
and
Programmes
Laundry
Warnings
and
Suggestions
Maintenance
and
Care
Troubleshooting
Service
GB
9
● Never dry articles that are contaminated with
flammable substances (petrol, oil, paint, hair
spray, creams, cooking fat or oils).
● Do not tumble dry rubber, foam rubber, plastic,
plastic foam, nappy pants or liners, polythene or
paper.
● Do not tumble dry large, very bulky items.
● Do not tumble dry acrylic fibres at high
temperatures.
● Complete each programme with its Cool Tumble
Phase.
● Do not turn off the dryer when there are still
warm items inside.
● Clean the filter after each use (see Maintenance).
● Empty the water container after each use (see
Maintenance).
● Clean the condenser unit after regular intervals
(see Maintenance).
● Do not allow lint to collect around the dryer.
● Never climb on top of the dryer. It could result in
damage.
● Always follow electrical standards and
requirements (see Installation).
● Always buy original spare parts and accessories
(see Service).
Disposal
● Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
● Disposal of your old dryer: cut the power cord and
remove the door before disposing of an old dryer.
Saving energy and respecting the
environment
● Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
● Always dry full loads - you save energy: single
items or small loads take longer to dry.
● Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings and Suggestions
Page: 9
Maintenance and Care
10
GB
Cleaning the condenser unit
Periodically (every month) remove the condenser unit
and clean any build up of fluff from between the plates
by rinsing it under the tap with cold water.
This should be done with cold water from the rear of
the condenser.
Removing the condenser:
1. Unplug the dryer and open the door.
2. Pull open the condenser cover (see diagram).
Release the three catches by turning 90˚ counter-
clockwise then pull on the grip and remove from
the dryer.
3. Clean the surface of the seals and replace, making
sure that the catches have been secured.
Cleaning the dryer
● External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
● Periodically clean the surface of the stainless
steel sensor inside the drum with vinegar to
remove water contaminates. Apply carefully with
a cloth, this will maintain the drying performance
of the dryer. The sensor is located on the plastic
vane inside the drum towards the front of the
dryer. Rotate the drum if necessary to locate it.
● Periodically (every 6 months) vacuum the front air
intake grille and vents at the rear of the dryer, to
remove any build up of fluff, lint or dust. Also to
remove accumulation of fluff from the front of the
condenser and filter areas, clean occassionally with
a vacuum cleaner.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
Switching off the electricity
! Unplug your dryer when not using it, when cleaning
it and during all maintenance operations.
Clean the filter after each cycle
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
When finished drying, clean the filter by rinsing it
under running water or with your vacuum cleaner.
Should the filter become clogged up, the airflow inside
the dryer will be seriously compromised: drying times
lengthen and you will consume more energy. It may
also damage your dryer.
The filter is found in front of the dryer trim (see diagram).
Removing the filter:
1. Pull the plastic grip of the filter upwards (see diagram).
2. Clean the filter and replace it correctly.
Ensure the filter is fully located flush into the tumble
dryer trim.
! Do not use the dryer without replacing the filter.
Empty the water container after each
cycle
Pull the container out of the dryer and empty it into a
sink or other suitable drain. Replace the water
container securely.
Always check and empty the container before you
start a new drying programme.
Check the drum after each cycle
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Water container
Handle
Condenser cover
Catches
Air intake
Filter
Tap
Rear
Front
Condenser unit
Page: 10
Troubleshooting
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water light is flashing
but the dryer has only been
running for a short period.
Empty water light is on and
the water container is not full.
The ON/OFF light flashes to
indicate a fault.
Programme finishes and
clothes are damper than
expected.
Possible causes / Solution:
● The plug is not plugged into the socket, or not making contact.
● There has been a power failure.
● The fuse has blown. Try to plug another appliance into the socket.
● You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
● The door is not closed securely?
● The PROGRAMMES knob has not been set properly (see Start and
Programmes).
● The START button has not been pressed (see Start and Programmes).
● You have set a delayed time (see Start and Programmes).
● The filter has not been cleaned (see Maintenance).
● The temperature setting is not ideal for the type of fabric you are drying
(see Start and Programmes, and see Laundry).
● The water container needs emptying? The empty water light is flashing?
(see Maintenance).
● The condenser needs cleaning? (see Maintenance).
● The correct drying time has not been selected for the load (see Laundry).
● The air intake grille or rear vents are obstructed (see Installation, and see
Maintenance).
● The items were too wet (see Laundry).
● The dryer was overloaded (see Laundry).
● The water container was probably not emptied at the start of the
programme. Do not wait for the empty water signal, always check and
empty the container before starting a new drying programme (see
Maintenance).
● This is normal, the light flashes when the container is full. If the light is on
but not flashing it is just a reminder to empty the container (see Start and
Programmes).
● Note down the other lights that are on and contact the Service Centre
(see Service).
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
Installation
Description
Start
and
Programmes
Laundry
Warnings
and
Suggestions
Maintenance
and
Care
Troubleshooting
Service
GB
11
Page: 11
Service
Spare Parts
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
Call an authorised technician if you experience problems
while using the machine.
The spare parts have been designed exclusively for
this appliance and not for other uses.
Service
12
GB
Before calling the Service Centre:
● Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
● If not, turn off the dryer and call the Service Centre
closest to you.
What to tell the Service Centre:
● name, address and post code.
● telephone number.
● the type of problem.
● the date of purchase.
● the appliance model (Mod.).
● the serial number (S/N).
This information can be found on the data label inside
the door of the machine.

Question & answers

There are no questions about the Ariston Thermo ASL70C yet.

Ask a question about the Ariston Thermo ASL70C

Have a question about the Ariston Thermo ASL70C but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Ariston Thermo ASL70C. Please make sure that you describe your difficulty with the Ariston Thermo ASL70C as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.