ANT MIM 30manual

U H F I N E A R M O N I T O R S Y S T E M S S I S T E M I I N E A R M O N I T O R U H F U H F I N E A R M O N I T O R S Y S T E M E EN USER MANUAL | Section 1 IT MANUALE D’USO | Sezione 1 DE BEDIENUNGSANLEITUNG | KAPITEL 1

ENGLISH MiM Series | User manual 2 3 Series User manual | MiM Series CONTENTS 1 | Introduction 4 2 | Description 4 2.1 | MiM 20T/MiM 30T transmitter 4 2.2 | MiM 20R/ MiM 30R beltpack receiver 6 3 | System setup 8 3.1 | Transmitter setup 8 3.2 | Beltpack receiver setup 9 4 | Troubleshooting 11 5 | Technical specifications 12 6 | Notes 37 The warnings in this manual must be observed together with the “User manual - Section 2”. PACKAGE CONTENT • 1x MiM 20T or MiM 30T transmitter - A • 1x PE-40 Earphones with accessories - B • 1x MiM 20R or MiM 30R receiver - C •  1x External power supply - D •  1x Antenna with BNC connector - E • 2x 1.5 Volts AA batteries - F • 2x 19” standard rack mounting kit - G •  1x User manual - Section 1 • 1x User manual - Section 2 A C B D F E G Note: for both models are available two versions - the standard one (PE-40) and that with Beyerdynamic FIRE ONE earphones, including its accessory kit and case cod. 150105021 (MiM 20) - cod. 150105024 (MiM 30).

ENGLISH MiM Series | User manual 4 5 Series User manual | MiM Series 1 | INTRODUCTION Thank you for choosing a A.N.T - Advanced Native Technologies - product! In our MiM series IEM systems we have put our passion and our technological background gained over the years, to offer products that suit your needs, maintaining the quality over time. Please,dedicatesomeminutestoreadthisinstructionmanualinordertoquicklyachieve the best performances from this product. For safety precautions, warranty and disposal, please refer to attached Section 2. For further information about all A.N.T products catalog, please visit our website: www.ant-intomusic.com 2 | DESCRIPTION 1 2 4 5 6 7 2 3 4 5 6 7 1 FRONT PANEL 2.1 MiM 20T/MiM 30T TRANSMITTER 1  PHONES  To monitor singer/musician listening, please connect headphones/earphones to this output. 2  HEADPHONE LEVEL  Use this control to adjust PHONES output level. Since high volume listening may permanentlydamageyourhearing,beforeeachsessionsetthevolumetoaminimum, then turn it up slowly. 3  INPUT LEVEL (MiM 30T only)  Adjusts the sensitivity of AF1 and AF2 transmitter inputs signals. Turn the knob clockwise to increase the volume, and counterclockwise to decrease it. 4 SET  Press this button to select functions, and to set transmitter parameters values. 5 LCD  The display shows indicators of audio levels (AF1 and AF2), the number of Group and Channel, the STEREO / MONO mode and lock. 6  UP/DOWN  Use these buttons to select higher or lower values/functions for each parameter. 7 POWER  Press it for 2 seconds to turn ON and OFF the unit. 1 2 3 6 4 4 5 1 REAR PANEL 2 1  “DC 12-18V” POWER SOCKET  Connect to this socket only the supplied power supply. 2  “AF1 INPUT” & “AF2 INPUT” CONNECTORS  Balanced audio inputs with “COMBO” (XLR-F/JACK da 6,35mm) connectors for signals to be transmitted. For MONO signal, use AF2 Input only.

ENGLISH MiM Series | User manual 6 7 Series User manual | MiM Series 3  ”AF LEVEL” AF 1 & AF2 INPUT LEVELS (MiM 20T only)  These controls allows you to adjust the signal levels of inputs AF1 e AF2. 4 ANTENNA SOCKET Connect the supplied antenna to this BNC socket. 5 PAD (MiM 30T only)  This selector allows to reduce the input signal by 12dB. 6  MONO/STEREO (MiM 20T only)  This selector allows to choose between Mono or Stereo listening. In the latter case the signals of AF1 and AF2 inputs are independent, while in the mono mode both earphones have the same signal (s). 4 4 3 3 2 2 1 1 5 5 6 8 6 7 9 9 MiM 20R MiM 30R 2.2 | MiM 20R/MiM 30R BELTPACK RECEIVER 1  VOLUME CONTROL WITH POWER SWITCH  To turn on the receiver, turn the knob to the right until you hear a click, to turn it off completely rotated to the left until it clicks. Turn the knob to the right to increase the volume, and to the left to decrease it. CAUTION: High listening volume may permanently damage your hearing. 2  RF/LOW BATT LED  With correct reception this indicator is lit green, it blinks red when the battery is low. 3  PHONES  3.5mm stereo mini-jack connector for earphones/headphones. 4 FIXED ANTENNA For signal receiving. 5 LCD Thedisplayshowsthelevelsofaudio,signalreception,andbatterycharge, numeric data for GROUP and CHANNEL and the lock. The STEREO mode indicator is active only when this mode is selected in the transmitter.  MiM 30R receiver has also status indicators of TONE, LIMITER and MIX functions, which are described later. 6  SET  Press this button to select functions, and to set receiver parameters values. 7  ESC (MiM 30R only)  Press this button to return to the main menu. 8 UP/DOWN  Use these buttons to select higher or lower values/ functions for each parameter. 9 BATTERY COMPARTMENT  To replace the batteries, lightly press on the sides of the compartment cover and lift forward.  Take out the discharged batteries, and insert two new batteries (respecting the figure in the compartment) thenclosethelid.Removethebatteriesfromthereceiver when not in use for extended periods. WEARING THE BELTPACK RECEIVER: Clip the receiver to a belt or to the shoulder strap of your guitar. For better fastening reliability it’s preferable to secure it as shown in the figure, then fasten it in a way that the belt is tight from the clip. 8 8

ENGLISH MiM Series | User manual 8 9 Series User manual | MiM Series 3 | SYSTEM SETUP For optimal transmission, the transmitter height must be at least 1 m (3ft) and put the antenna vertically, upward. Avoid placing the transmitter close to metal objects or to digital devices (CD players, computers, console, and so on). The transmitter and receiver must be placed to have a straight “visual contact”. 3.1 | TRANSMITTER SETUP The main screen of the display shows radio frequency, the selected operating mode (MONO/STEREO), the transmission level of the AF1 and AF2 signals and the lock, if it’s activated. 1 GROUP SELECTION  Press the SET button until when “GROUP” appears in the display.  Use the up and down buttons to select the desired group of frequency, then press again SET to confirm the choice. 2 CHANNEL SELECTION  Press the SET button until when “CHANNEL” appears in the display.  Use the up and down buttons to select the desired channel, then press again SET to confirm the choice. Simultaneously using more systems, it’s better to have them on the same group but on different channels. 3 STEREO OR MONO OPERATING MODE (MiM 30T only) PresstheSETbuttonuntilwhen“STEREO”or“MONOappearsinthedisplay.Usethe up and down buttons to select the desired mode, then press again SET to confirm the choice. In Mono mode you will listen to AF2 signal, while in STEREO you listen to both AF1 and AF2 signals. ATTENTION: for MiM 20T the selection for MONO/STEREO mode is mechanically achieved by a switch on transmitter rear panel. 4 LOCK ACTIVATION AND DEACTIVATION  Press the SET button until when the icon “LOCK” start flashing in the display, then press the up and down buttons to confirm the choice.  To deactivate LOCK and edit the settings, you need to press the button “SET” for 2 seconds.  ATTENTION: when LOCK icon is displayed, you can see the unit settings, but these settings are not editable. 3.2 | BELTPACK RECEIVER SETUP The main screen of the display shows radio frequency, the selected operating mode (MONO/STEREO), the transmission level of the AF1 and AF2 signals, batteries status, and the lock, if it’s activated. MiM 30R display shows also information about TONE, LIMITER, and MIX features. To do your settings, use the SET button and the up and down buttons. In MiM 30R there is also an ESC button, useful to immediately go back to main menu. Press on the sides of the lid to lift the lid, and to access to the hidden buttons: ESC and SET (MiM 30R) o up and down (MiM 20R). 1 AF1 AND AF2 CHANNELS VOLUME BALANCE (MiM 30R only)  Press the up/down buttons to adjust volume balance between AF1 and AF2 of a Stereo signal If the transmitter is in Mono mode, using the up/ down buttons you set the position of the signal in the Stereo field. 2 GROUP SELECTION Press the SET button for 2 seconds until when “GROUP” starts flashing in the display. Use the up and down buttons to select the desired frequency group, then press again ESC (MiM 30R) or SET (MiM 20R) to exit the menu. 3 CHANNEL SELECTION  Press the SET button for 2 seconds to access the settings menu, then press again SET until when “CHANNEL” starts flashing in the display.  Use the up and down buttons to select the desired frequency group, then 1 4 2 3 1 2 4 5 7 6 3 8

ENGLISH MiM Series | User manual 10 11 Series User manual | MiM Series press again ESC (MiM 30R) or SET (MiM 20R) to exit the menu.  Simultaneously using more systems, it’s better to have them on the same group but on different channels.  If the transmitter is in Mono mode, using the up/down buttons you set the position of the signal in the Stereo field. 4 TONE SELECTION (MiM 30R only)  Press the SET button for 2 seconds to access the settings menu, then press again SET until when “TONE” starts flashing in the display. Use the up and down buttons to activate (ON) or deactivate (OFF) TONE feature. TONE ON boosts high frequencies. 5 LIMITER SELECTION (MiM 30R only)  Press the SET button for 2 seconds to access the settings menu, then press again SETuntilwhen“LIMITER”startsflashinginthedisplay.Usetheupanddownbuttons to activate (ON) or deactivate (OFF) LIMITER feature. LIMITER ON reduces sudden peaks, thus protecting your hearing. 6 LOCK (MiM 30R only)  Press the SET button for 2 seconds to access the settings menu, then press again SETuntilwhenthelockiconstartsflashing.Usetheupanddownbuttonstoactivate (ON) or deactivate (OFF) the lock. ATTENTION: when LOCK icon is displayed, you can see the unit settings, which are not editable. 7 MIX (MiM 30R only)  Press the SET button for 2 seconds to access the settings menu, then press again SET until when “MIX” starts flashing in the display. Use the up and down buttons to activate (ON) or deactivate (OFF) MIX feature.  MIX ON allows to listen both transmitter input signals - AF1 and AF2 - using the supplied earphones. To balance the signal between AF1 and AF2 inputs, press the up and down buttons. You can choose among 31 available positions: In MIX -0- position, AF1 and AF2 input signals are balanced.  Press the (button arrow up) to increase AF1 signal versus AF2 signal: 1-, 2-, 3-, 4-, 5-, 6-, 7-,8-, 9-, A-, b-, C-, d-, E-, and F- (max)  Press the (button arrow down) to increase AF2 signal versus AF1 signal: -1, -2, -3, -4, -5, -6, -7, -8, -9, -A, -b, -C, -d, -E, and -F (max) 8 BATTERIES LEVEL INDICATOR This icondisplays in 4 steps thebattery chargelevel. Wheninside theiconthere’s no bars present and LOW BATT LED flashes, please immediately replace the batteries. 4 | TROUBLESHOOTING PROBLEM LEDS SOLUTION No sound or very low sound level. Power LED turned off. Make sure the batteries are not discharged and that the receiver is turned on. Transmitter LCD turned off. Check the connection between power supply and the transmitter. Turn on the transmitter. Receiver RF indicator is off. Make sure that transmitter and receiver are set to the same frequency. Reduce the distance between transmitter and receiver, and verify that the two devices are in direct visual contact. Make sure that the transmitter antenna is mounted correctly. Receiver turned on and RF light on. Raise the volume of the receiver and check earphones connection. Check the input level of the transmitter and, possibly, increase it. Distortions or unwanted interferences. Receiver RF antenna lit. Increase the distance from possible causes of interference (digital control devices, such as CD player, console ...). Use a different frequency. Distorted sound. Receiver LOW BATT LED flashes. Too high level indicator of the transmitter. Replace the batteries. Turn down the volume control of the transmitter or the volume of the source device. Listening to a Mono signal only from one hearphones side. Transmitter is in Stereo mode. Set the transmitter in Mono mode. Mode Stereo and MIX activated: you want to hear only the right input signal transmitter, even if the transmitter is in Stereo mode and both the transmitter inputs are used. (MiM 30 only). Transmitter is in Mono mode. Set the transmitter in Stereo mode. Listening to two independent mono signals in left and right earphones, but you want to hear the signals in both earphones (MiM 30 only). Activate MIX in the transmitter.

ITALIANO Serie MiM | Manuale d’uso 13 12 Series User manual | MiM Series 5 | TECHNICAL SPECIFICATIONS BELTPACK RECEIVER MiM 20R MiM 30R Modulation FM stereo FM stereo Range of frequencies 823-832MHz + 863-865MHz 823-832MHz + 863-865MHz Channels available 96 (8 groups with 12 channels each) 96 (8 groups with 12 channels each) Frequency response 50Hz - 15.000Hz（±3dB） 50Hz - 15.000Hz（±3dB） Signal-to-noise ratio ≥80dB ≥80dB Audio outputs 3,5mm stereo mini-jack 3,5mm stereo mini-jack Max output level 50mW x 2 50mW x 2 Controls Volume, up, down, SET Volume, up, down, ESC, SET Indicators Multi-function LCD, LOW battery, RF Multi-function LCD, LOW battery, RF Power supply 2 AA 1.5V batteries 2 AA 1.5V batteries Operating time > 12h, battery-dependent > 12h, battery-dependent Dimensions (W x H x D) 64 x 90 x 23 mm 2.51” x 3.54” x 0.9” 64 x 90 x 23 mm 2.51" x 3.54" x 0.9" Weight 95 g - 0.09 oz 95 g - 0.09 oz TRANSMITTER MiM 20T MiM 30T Modulation FM stereo FM stereo Range of frequencies 823-832MHz + 863-865MHz 823-832MHz + 863-865MHz Channels available 96 (8 groups with 12 channels each) 96 (8 groups with 12 channels each) Output power 10mW 10mW Frequency response 50Hz - 15.000Hz（±3dB） 50Hz - 15.000Hz（±3dB） Signal-to-noise ratio ≥80dB ≥80dB Inputs 2 x balanced XLR 2 x balanced COMBO - XLR and 6,35mm. (1/4”) jack Input impedance 10K Ohm 10K Ohm Antenna connectors BNC socket BNC socket Front panel controls Headphones volume, SET and up/down buttons, power button Headphones volume, input level, SET and up/down buttons, power button Rear panel controls 2 x AF LEVEL, MONO/STEREO switch 0/-12dB PAD switch Indicators Multi-function LCD Multi-function LCD Dimensions (W x H x D) 212 x 44 x 96 mm 8.34” x 1.73” x 3.77” 212 x 44 x 96 mm 8.34” x 1.73” x 3.77” Weight 560 g - 19.7 oz 560 g - 19.7 oz Le avvertenze nel presente manuale devono essere osservate congiuntamente al “Manuale d’uso - Sezione 2”. INDICE 1 | Introduzione 15 2 | Descrizione 15 2.1 | Trasmettitore MiM 20T/ MiM 30T 16 2.2 | Ricevitore Beltpack MiM 20R/ MiM 30R 18 3 | Impostazione del sistema 20 3.1 | Impostazione del trasmettitore 20 3.2 | Impostazione del ricevitore beltpack 21 4 | Soluzione dei problemi 24 5 | Caratteristiche tecniche 25 6 | Note 37