View a manual of the AEG MC 4445 DVD below. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.
English 35 1 CD/DVD tray 2 Reverse button / Radio chan- nel down ( /CH-) 3 Reverse search button / Chan- nel scan down ( /TUNING-) 4 IR receiver 5 LCD display 6 Play/Pause / Auto scan button ( ) 7 Power button (STANDBY) 8 Fast forward search button / Channel scan up ( /TUNING+) 9 Forward button / Radio chan- nel up ( /CH+) 10 Speakers 11 FM Antenna input (FM ANT) 12 S-Video output 13 Composite video output 14 MR/ML audio output 15 Digital audio output (Coaxial) 16 HDMI Output 17 Tone button (AUDIO/ST/MO) 18 USB interface 19 VOL+/- volume control 20 Stop button (STOP) 21 Feature selection button (FUNCTION) to select between DVD, USB and RADIO. 22 Menu button (MENU/PBC) 23 Power supply 24 POWER ON/OFF button (Power ON/OFF) 25 SCART output Components (Fig. 1)
English 36 Remote control (Fig. 3) 1 EQ: Adjust the sound options. 2 OSD: Shows the playback status on the screen. 3 LANGUAGE: Changes the audio settings. 4 FUNCTION: Allows you to choose between DVD, USB and RADIO. 5 TITLE: Shows the title menu of the DVD/VCD. 6 MENU: Shows the main menu of the DVD/VCD. 7 PBC: To show the Playback- Control for VCD. 8 PROGRAM: Shows the play list. 9 A-B: To select the section to be repeated. 10 CLEAR: Deletes titles from a play list. 11 REPEAT: To repeat title, Chap- ter, etc. 12 SLOW: Slow motion. Use the “PLAY “ button to continue playing the film. 13 RETURN: Returning to the previous menu. 14 STOP: Stops the playback. 15 P/N: AUTO/NTSC/PAL Changes the TV type. 16 ENTER: Confirms a choice. 17 SEARCH: Allows you to go to a certain section of the CD/DVD directly. Starts the automatic channel scan in the radio mode. 18 : Fast forward. Allows to search and save stations in the radio mode. : Fast backward. Allows to search and save stations in the radio mode. 19 VOL+: Increases the volume. VOL -: Decreases the volume. 20 MO/ST: Allows you to change between stereo and mono in the radio mode. 21 “MUTE“: Turns sound off. Keep the button pressed for around. 3 sec to turn the internal speaker off and on. 22 : Shifts to the next chapter or title. In radio mode this button can be used to skip through the saved stations. : Shifts to the previous chapter or title. In radio mode this button can be used to skip through the saved stations. 23 MEM: Stores radio stations in the radio mode. 24 Cursor buttons: To navigate through the screen menus. 25 SETUP: Starts the setup menu. 26 “PLAY “: Starts the playback. 27 “PAUSE “: Freezes the pic- ture. Continue to play the film using the “PLAY “ button 28 ZOOM: Zooms in or out. 29 STEP: Freezes the picture. Press again to show the next image. Continue to play the film using the “PLAY “ but- ton. 30 10+: To select chapters/tracks above 9. Press this button again to increase by 10 at a time. 31 Numerical buttons: For direct selection of chapter or song number. 32 SUBTITLE: Enables/disables the subtitles. 33 “ “ POWER: Enables the standby mode. 34 ANGLE: To select the viewing angle.
English 37 Technical data Device parts ........................................................................................................35 Remote control ..................................................................................................36 Technical data ....................................................................................................37 Safety instructions. ............................................................................................39 Setting up and connecting . ............................................................................ 41 Starting up . .........................................................................................................42 About the DVD-Player .....................................................................................45 Playing media . ....................................................................................................46 Working in file mode .......................................................................................50 Change settings . ................................................................................................53 Radio Station Set-up. ........................................................................................58 Troubleshooting . ................................................................................................59 Disposal . ...............................................................................................................60 Declaration of conformity. ...............................................................................60 OSD Menu Overview. ......................................................................................... 61 Table of Contents Device type Music Center with DVD Model MC 4445 DVD Power supply 100-240 V, 50/60 Hz Power consumption 20 W Dimensions with stand (W x H x D) 401 x 236 x 113 mm Weight 1.2 kg Laser Semiconductor laser Signal PAL Signal-to-noise ratio >=95 dB Video output 1.0 V (P-P) 75 Ω Analog audio output 2.0 V (P-P) Digital audio output 0.5 V (P-P) 75 Ω S-Video Output (Y) 1.0 V (P-P), 75 Ω (C) 300 mV (P-P), 75 Ω Radio frequency range FM 87.5 ~ 108 MHz Operating environment 5°C to 35°C, level base Compatible media DVD-Video (DVD Disc, DVD ±R/RW) MPEG-4 Video (from CD/DVD Disc, DVD±R/RW, CD-R/RW) Audio CD (from CD Disc, CD-R/RW) Video CD (from CD Disc, CD-R/RW) MP3 files (from CD/DVD Disc, DVD±R/RW, CD-R/RW) Regional 2 (= Europe, Greenland, South Africa, Egypt and Middle East, Japan) Music power 30 W (PMPO)
English 38 Many thanks! Symbols in this operating manual Manufacturer address Thank you for choosing the “MC 4445 DVD” Music Center with DVD! We would like to wish you much joy with your machine and thank you for your purchase! Important instructions for your safety are especially marked. You must follow these instructions to avoid accidents and damage to the machine: WARNING: Warns against dangers to your health and indicates potential risks of injury. CAUTION: Indicates potential hazards for the player or other objects. NOTE: Highlights tips and information for you. Clatronic International GmbH Industriering Ost 40 47906 Kempen We reserve the right to make technical and design-related changes in the course of ongoing product improvements.
English 39 Operating manual Children Power supply Safety instructions Read the complete operating manual before using the player. Keep the manual in a safe place. If you pass the player on to a third party, pass on the operating manual as well. Non-compliance with this manual can lead to severe injuries or damage to the machine. We assume no liability for damage caused as a result of non-compliance with this operating manual. The player may only be used in households for private use. It is not suit- able for commercial use. Do not leave the machine unattended, and do not use it if children or persons who cannot assess the risk are nearby. Children or persons who cannot assess the risks are not allowed to use the player. Keep the player out of reach. Packaging material must not be used to play with. There is a risk of suffocation. The machine is operated with electrical current, which means there is in principle a risk of electric shock. For this reason, pay particular caution to the following: Never touch the plug with wet hands. If you want to pull the plug out of the plug socket, always pull directly on the plug. Never pull on the cable as it could tear. Make sure that the power cable is not bent, caught or run over and that it does not come into contact with heat sources. Make sure that the power cable is not wound around the device while in operation. Never place the machine on the power cable while it is being oper- ated. Only use extension cables that are designed for the power consump- tion level of the machine. Keep the appliance away from rain and any moisture. Only operate the machine if the electrical voltage stated on the type plate agrees with the voltage on your plug socket. The wrong voltage can destroy the machine. Do not stand vases etc. on the appliance. Water could seep into the appliance. Do not open the appliance. Pull out the mains plug if the appliance is not to be used over a longer period of time. Take care that nobody can trip over the power supply cable.
English 40 Laser Transport Where to position the appliance Operation Intended use This appliance is classified as laser appliance of class 1 (CLASS 1 LASER). The associated label is attached to the outside of the appliance. Laser beams can damage the eyes. Therefore observe the following: Do not open the appliance. Do not attempt to dismantle the appli- ance. In order to avoid any danger: Have service work only carried out by the manufacturer or an authorized service workshop. In order to avoid damage to the DVD, you should remove it before transporting the appliance. Never move the machine when it is in operation. Safe operation of the appliance presupposes that it is positioned in an appropriate place. Therefore observe the following: Protect the appliance against the influence of weather. Never use it in the open-air. Protect the appliance against moisture. Do not place liquid filled vessels, e.g. vases, on the device. Do not place the device on or in close proximity to heat sources such as heaters, ovens, etc. Do not expose the appliance to direct sunlight. Place the appliance so that a sufficient air supply is assured. This is to avoid a build up of heat inside the appliance. Make sure that the ventilation slots are not blocked. Protect the appliance against the mechanical vibrations. Always place the device on a firm, even base. Protect the remote control against weather influences, moisture and high temperatures (e.g. by direct sunlight). The player is able to show a still image on the TV-screen/monitor over an unlimited period of time. This can cause damage to the screen. It is therefore advisable to activate the screen saver Page 54, “System settings“. Do not increase the volume when the player is just playing very quiet sections. This could damage the speaker if very loud passages start all of a sudden after the quiet section. Do not move the player with a DVD inserted. This could damage the DVD. Do not put your hands into the DVD-slot. You could be injured. Place only DVDs or CDs on the DVD-tray, as otherwise the player may be damaged. Switch the player off by the On/Off-switch if it is not going to be used for a longer period of time. Please disconnect the mains plug during thunderstorms. The DVD-Player is solely intended for the following tasks: Playing of Video DVD/Video CD. Playing of Audio-CD.
English 41 Defect Unpacking Setting up Wall mounting Playback of files via USB. Reception of radio programmes. Any other use is considered non-intended use and is prohibited. If the machine should become defective at some point: If the power supply cable for this appliance is damaged, it must be replaced by the manufacturer or his customer services, in order to avoid hazards. Should fluid have seeped into the player or if the player has been dropped down or damaged in any other way, the player must be examined by an authorized dealer. Disconnect the player from the power supply and consult an authorized dealer. Setting up and connecting Unpack the appliance and all accessories and check that the contents are complete. CAUTION: Always transport/send the player in its original packaging to prevent it from being damaged. Keep the packaging for this purpose. Dispose of unnecessary packaging material in accordance with the regulations applicable in your country. NOTE: Get in touch with your dealer immediately if you notice damage caused by transport. 1. Put the stand on the base plate. Ensure that the guiding rail has been aligned with the notch. 2. Mount the stand as shown. 3. Put the device on a stable, horizontal and flat surface. Keep a dis- tance of at least 10 cm from walls and other objects. 4. Connect the mains cable to the mains connection socket (Fig. 1/23). 5. Connect the device to a properly installed power socket. You can also mount the device to a wall (mounting accessories not included). CAUTION: Make sure that there are no hidden cables in the wall that could be damaged!
English 42 Remote control battery installation NOTE: Note the cable range! In order to mount the device, ensure a power outlet is within range of the input lead. Furthermore, ensure that the device can be connected to your TV set by an AV cable. The distance between the wall mounting fixtures is 94 mm. 1. Drill two horizontal holes whilst minding this distance. 2. Equip the holes with dowels and screws. 3. Mount the device onto the screws and check if it has been securely positioned. 4. Connect the mains cable to the mains connection socket (Fig. 1/23). 5. Connect the device to a properly installed power outlet. Starting up WARNING: Leaking out battery acid can damage your health. Remove the battery from the battery compartment as soon as it is exhausted or if the remote control is not going to be used for a longer period of time. Wipe up leaked out battery acid with a cloth. In case of skin contact immediately wash the affected area. Seek medical advice if battery acid has been swallowed.In case of contact with your eyes wash out the eyes and seek medical advice. CAUTION: Mismatching battery types or new and used batteries must never be used together. Different battery types have different properties. Do not use old and new batteries together. The mutual use of old and new batteries can shorten the lifetime of the new batteries and possibly result in leakage of the old batteries. When disposing of old batteries you should strictly comply with the legal and environmental regula- tions applicable in your country. Do not throw batteries into fire! NOTE: The lifetime of the enclosed batteries may be shortened because of storage. 1. Open and remove the battery compartment cover. 2. Insert two batteries of type AAA/R03 (1.5 V), ensure correct polarity (+ and -). Start with the negative pole (-). 3. Attach and close the battery compartment cover. NOTE: The signals from the remote control are transmitted to the DVD-Player by infrared light. You should therefore take care that the DVD-Player is not exposed to the direct sunlight. This could make the transmission of signals from the remote control to the DVD-Player impossible.
English 43 Audio-/video cables Connecting the Video cable Fig. 1/25 Fig. 1/16 FIg. 1/13 Effective range of the remote control If you want to use the remote control it has to be pointed at the remote control sensor on the front of the device. The distance between remote control and sensor should not exceed 7m. The angle of the remote con- trol to the remote control sensor to right, left, top and bottom should not exceed 30°. NOTE: An undisturbed operation can be guaranteed only with Audio/Video lines up to 1.5 m length. The video cable transmits the video data from your DVD-Player to the TV or the Video-Projector. There are four different options to connect the DVD player to your TV/ video projector. Choose a suitable option in reference to your playback device. NOTE: In case you are not using a SCART or HDMI connection, you have to set up an additional audio connection in order to transmit audio data (sound). SCART SCART is used to transmit both Video and Audio data. 1. Insert the SCART plug firmly into the jack on the left side of the device. 2. Plug the SCART jack into the corresponding socket on your playback device. HDMI Connection Connecting using the HDMI cable guarantees very good playback quality. Use HDMI to transmit video as well as audio data. 1. Plug the HDMI connector into the jack on the right side of the device. 2. Plug the HDMI connector into the corresponding jack on your play- back unit. NOTE: Select the submenu “HD output“ in the “System Setup“ menu. Set the resolution to match your playback unit. Composite video Composite video only submits video data. 1. Insert the composite video plug into the jack on the right side of the device. 2. Insert the composite plug into the related jack on your playback device.
English 44 Fig. 1/12 Connecting an audio cable Fig. 1/14 Fig. 1/15 Antenna connection Fig. 1/11 S-Video Connecting using the S-Video cable guarantees very good playback quality. Only video signals are transmitted using S-Video. 1. Plug the S-Video connector into the jack on the right side of the device. 2. Plug the S-Video connector into the corresponding jack on your playback unit. NOTE: In DVD or USB mode you can turn off the internal speaker sound. To do so, keep the MUTE button (Fig. 2/21) pressed for around 3 sec during playback. Keep the button pressed again to turn on the sound back on. You can choose between two submission methods for sound signals. You must generally choose first whether you would like to have the sound coming from your TV, or through a Stereo Amplifier. The Audio cable must then be connected to the TV or an amplifier accordingly. NOTE: If your amplifier is equipped with a digital output, you should use the amplifier. You will experience a much better audio quality, and the installation is much easier. Stereo Connect the two audio cables for the right and left-hand audio channel to your playback device or your amplifier. 1. Insert the audio plug into the jack on the right side of the device. 2. Plug the Audio jacks into the corresponding sockets on your play- back device or your amplifier. NOTE: Use the VOLUME +/- buttons (Fig. 2/19) to adjust the volume to a comfortable and safe level. If the volume has been reduced to “00“ no sound will be broadcast. Digital Connect the Coaxial cable for transmission of digital Audio signals to your playback device or your amplifier. 1. Insert the audio plug into the jack on the right side of the device. 2. Plug the Audio jack into the corresponding socket on your playback device or your amplifier. Antenna input This device has an integrated FM radio receiver. FM/UKW Reception: Connect the cable of your antenna unit to the FM jack on the right side of the device.
English 45 Inputs on the side of the device Fig. 1/18 Turning on the device Fig. 1/25 Terminology USB Input Insert a USB storage medium directly into the corresponding socket of the device. Turn on the DVD player by pressing the main “POWER ON/OFF“ switch on the left side of the device so that it indicates the position “ON”. If the device remains in standby mode, press the STANDBY button on the device (Fig. 1/7) or on the remote control (Fig. 2/33) to switch the player on. About the DVD-Player With this DVD-Player you can play a vast variety of DVD-formats Page 37, “Technical data“. However, you must be aware that in many cases DVDs are encrypted with a so-called “Regional Code”. This specifies for which region in the world the DVD is intended. As an example, the DVDs marked with regi- onal code “1” are intended for the USA and Canada. DVDs with regional code “2” are for use in Europe. NOTE: With your DVD-Player you can only play DVDs with regional code “2”. There are both lots of burning and compressing methods as well as high quality differences in (burned) CDs/DVDs. Moreover, the music industry has not yet agreed on a fixed standard for copy protection. This may, in very isolated cases, result in problems when relaying CDs, DVDs and MP3 CDs. This is no malfunction of the player. Furthermore, there may be isolated problems when playing CDs or DVDs which were created on a PC (e.g. holiday photographs). In case of pro- blems check the settings of the DVD writing program on your computer. You should in particular make sure that the DVD has been finalized. For further information on this matter please refer to the operating manual of your recorder. Input Not Possible If you select an invalid function or entry, the message “INVALID KEY“ will appear on the screen. Track: ”Track” is the designation for sections on an Audio-CD. This may be a song, the set of a symphony, etc. Title/Chapter: Video-DVDs are divided into “Title” and “Chapters“. A “Title“ may be e.g. a particular film, the “Chapters“ may be subsections of this film. HDMI: High Definition Multimedia Interface is an interface for transmitting high definition digital video data as well as digital audio data. MPEG4: Your DVD player is also suitable for playing back files that have been compressed using the MPEG-4 system (short for Moving Picture Experts Group-4). MPEG-4 is a compression method by
English 46 Using the remote control Loading a CD/DVD Understanding the onscreen CD-menu Understanding the onscreen DVD-menu means of which large quantities of data can be reduced without any noticeable loss of picture and sound quality. NOTE: It is not possible to guarantee full compatibility with all of the com- pression methods used worldwide, particularly when more than one soundtrack or subtitles are involved. Also MPEG 4 files with integrated special functions such as a menu, subtitles etc. are not always sup- ported. This is no malfunction of the player. Playing media You transmit commands to the DVD-Player via remote control. It is thus important to point the end of the remote control towards the DVD- Player. NOTE: If the device is not yet in DVD Mode, press the FUNCTION (Fig. 2/4) button on the remote control. 1. Open the CD/DVD compartment by opening the cover at the flap at the front. 2. Place a CD/DVD with its label facing to the front onto the center until it mechanically clicks into place. 3. Close the CD/DVD cover. 4. The display (Fig. 1/5) first shows “LOAd”. When playing CDs the following status information is displayed on screen: Media type (1) Current track/total number of tracks (2). Audio output (3): If the MUTE button (Fig. 2/21) on the remote control has been pressed, the audio output is interrupted. Repeat (4): - „x“: No repeat. - „1“: The current track is repeated. - „A“: All tracks are repeated. Set the repeat using the REPEAT button. Time (5): This provides information about the duration and the remaining play time. By standard the play time expired of the current track is displayed. The display is in hours, minutes and seconds. Press the OSD-button (Fig. 2/2) once or several times to have further times displayed. The following possibilities are available for selection - time remaining to the end of the track, - playback time of the CD so far, - time remaining to the end of the CD. - Display is hidden. When playing DVDs you can view the on-screen menu by pressing the OSD-button (Fig. 2/2).
English 47 Starting the replay Interrupting the replay Changing Audio-Language/ Audio-Mode Showing subtitles DVD-menu Page 1 Media type (1) Current title/total number of titles (2). Current chapter/total number of chapters (3). Time (4): This provides information about the duration and the remaining play time. By standard the play time expired of the current chapter is displayed. The display is in hours, minutes and seconds. Press the OSD button again to display the DVD menu page 2. DVD menu page 2 Output language (1) Type of audio output (2). Subtitles (3): Shows if and in what language subtitles are displayed. Viewing Angle (4): If the DVD offers the option of selecting different viewing angles the number of viewing angles as well as the current selected viewing angle is displayed. Press the OSD-button (Fig. 2/2) once or several times to have further times displayed. The following possibilities are available for selection. - time remaining to the end of the chapter, - expired playing time of the titles, - time remaining to the end of the title. 1. Place the CD/DVD on the CD/DVD-tray Page 46, “Loading a CD/ DVD“. 2. Press the “PLAY “ -button (Fig. 2/26) on the remote control. NOTE: If the replay does not start or the replay is of poor quality, you should check the default settings of the DVD-Player. 1. Press the “PAUSE “ -button (Fig. 2/27) on the remote control. The replay is interrupted, the currently visible image is “frozen“. 2. Press the “PLAY “ -button (Fig. 2/26) on the remote control to restart the “normal“ replay. Press the LANGUAGE-button (Fig. 2/3) several times to change the Audio language. The available audio languages depend on the DVD. Audio-/MP3-CDs only: By repeatedly pressing the ST/MO (Fig. 2/20) button you can set the audio mode to “Mono” or “Stereo”. Press the SUBTITLE-button (Fig. 2/32) to display the current subtitle status. Press the button several times if you would like to activate or deactivate the subtitle function or if you want to choose a different subtitle language. The available subtitle languages depend on the DVD.
English 48 Stopping the replay Selecting previous chapter/track Selecting next chapter/track Selecting track directly Access a sequence by menu Repeat DVD titles/chapters Repeat a CD track Repeat DVD/CD Stop repeating Press the STOP-button (Fig. 2/14) during replay. The replay stops. Press the “PLAY “ button (Fig. 2/26) again, to continue the replay from the last position. Press the STOP -button (Fig. 2/14), twice to stop the replay completely. Press the “PLAY “-button (Fig. 2/26) again, to replay the CD/DVD from the beginning. Press the “ “ button (Fig. 2/22) to jump to the start of the previous chapter or track. Press the “ “ (Fig. 2/22) to jump to the start of the next chapter or track. Enter the number of the desired chapter/track with the Numerical Buttons on the remote control (Fig. 2/31). After a short time the playback of these tracks will start. Using the On-Screen menu, you can easily navigate to any sequence of a media. Proceed as follows: 1. Press the SEARCH button (Fig. 2/17). The media-specific menu will be displayed. 2. You will see an entry mark (1) in the menu. Move it into the desired area (e.g. “chapter”) using the Cursor Buttons (Fig. 2/24). 3. Now enter the point where playback shall start from. Depending on the media type, this can be a track number, a chapter or a time point. This is entered by the Numerical Buttons (Fig. 2/31). 4. Press the ENTER button (Fig. 2/16) to start playback from this point. 1. Select the chapter or title to be repeated. 2. Press the REPEAT button (Fig. 2/11). “REP: [OFF]” will be displayed on-screen. 3. Press the REPEAT button again till “REP: [CHAPTER]” or “REP: [TITLE]” appears on the display respectively. 1. Select the track to be repeated. 2. Press the REPEAT button (Fig. 2/11). “REP [REP 1]” appears on- screen. Press the REPEAT button (Fig. 2/11) repeatedly till “REP: [REP ALL] appears on-screen. Press the REPEAT button (Fig. 2/11) repeatedly till “REP: [OFF]” appears on-screen.
English 49 Selecting a section to be repeated Using the DVD-menu Using fast forward or reverse Enlarging a screen section Changing the viewing angle You can define a freely selected section to be automatically repeated. To do this, proceed as follows: 1. Mark the beginning of the section to be repeated. During repetition press the button A-B (Fig. 2/9) on the remote control once. The message “REPEAT A-“ appears on the screen. 2. Mark the end of the section to be repeated by pressing the A-B button on the remote control once again. The message “REPEAT A-B “ appears on the screen. The previously marked section is now repeated. Press the A-B-button again to stop the repetition. NOTE: The section of an audio/MP3 CD to be repeated has to be part of one track. Normally each DVD has its own menu. Here you can choose chapters, make settings, etc. This menu is specific for the DVD and can thus not be explained in detail. Press the MENU-button (Fig. 2/6) to access the DVD-menu. Use the Cur- sor Buttons (Fig. 2/24) to navigate in the Menu. Press the ENTER-button (Fig. 2/16) to confirm. If you are in a menu area for direct chapter selection, you can enter the number of this chapter with the Numerical Buttons (Fig. 2/31) on the remote control. The DVD-Player has a fast forward and a fast reverse feature. 1. Press the (Fig. 2/18) or button (Fig. 2/18) to start fast forward or fast reverse. The current replay direction and the speed, e.g. “FOR- WARD X2“ is now displayed on screen. 2. Press the or. button several times in order to change the speed. The speed can be accelerated by factor 2, 4, 8 or 20. 3. Press the “PLAY “-button (Fig. 2/26) to restart the “normal” replay when the desired section is reached. You can change the screen section when viewing DVDs, VCDs or images. Press the ZOOM-button (Fig. 2/28) to change the screen section. Press the button several times to select the suitable zoom factor or to return to the original zoom factor. NOTE: Use the Cursor Buttons (Fig. 2/24) to navigate in the picture you have zoomed into. Some DVDs offer the possibility to select the viewing angle. Press the ANGLE-button (Fig. 2/34) to change the viewing angle. NOTE: If changing the Viewing Angle is not possible, the message “INVALID KEY“ will be displayed. Repeat pressing the button to choose a different viewing angle, or to return to the original viewing angle.
English 50 Adjusting the volume Creating a playlist (CD/DVD/MP3) CD: DVD/MP3: Deleting a playlist (CD/DVD/MP3) Press the VOLUME + button (Fig. 2/19) to increase the volume. Press the VOLUME - button (Fig. 2/19) to reduce the volume. NOTE: Please remember, that this will only change the output volume of the DVD-Player. In order to adjust the volume to your requirements you may also have to change the volume of the playback device. You may want to replay the titles, e.g. on a CD, in a different order to the order determined by the producer. The function “Create Playlist“ you can create your own playing order. To do this, proceed as follows: 1. Press the PROGRAM button (Fig. 2/8). A table is displayed. Here you can enter the desired sequence of tracks (on CDs), the folder/tracks (on MP3 CDs) or chapter/title (on DVDs). NOTE: However, your playlist will be lost when switching off the DVD- Players or when inserting a new CD/DVD. 2. Use the Cursor Buttons (Fig. 2/24) to navigate in the table. 3. Enter the desired track (in the case of CDs) or the desired title and chapter (for DVDs) at the appropriate position in the table. Use the Numerical Buttons (Fig. 2/31) for this purpose. For entries above 9 you firstly need to press the button 10+ (Fig. 2/30). 4. Use the Cursor Buttons (Fig. 2/24) to select the command “ PLAY” at the bottom of the screen to save the input. 5. Press the ENTER-button (Fig. 2/16) on the remote control to confirm this command. 1. Press the PROGRAM-button. You will now see a table (Fig. CD or Fig. DVD/MP3). 2. Use the Cursor Buttons (Fig. 2/24) to manoeuvre to the command “CLEAR” at the bottom of the table. 3. Press the ENTER-button (Fig. 2/16) on the remote control to confirm this command. 4. Press the PROGRAM button to terminate this procedure. Working in file mode As well as being able to play back “normal“ films or music from CDs/ DVDs, this DVD player is also able to play back video or audio files from CDs or DVDs which are stored in the file system. Such media are fre- quently available if you create CDs of digital photographs or MP3 music on your computer. NOTE: If the device is not yet in DVD mode, press the FUNCTION button again (Fig. 2/4) on the remote control.
English 51 Using CD/DVD Using a USB medium Selecting file/directory and starting replay 1. Place the CD or DVD on the tray Page 46, “Loading a CD/DVD“. 2. Select the desired file(s) and start the replay Page 51, “Selecting file/directory and starting replay. By means of the USB connection you can connect numerous devices to the DVD Player. Examples of such devices are USB memory sticks or digital cameras. This device has been developed in accordance with the latest technical developments in the USB field. Unfortunately the large number of dif- ferent types of USB storage media on offer today makes it impossible to guarantee full compatibility with all USB storage media. For this reason there may be problems in rare cases with playing back from USB storage media. This is not a malfunction of the device. 1. Plug a USB memory device directly into the corresponding port of the DVD player (Fig. 1/18). 2. Press the FUNCTION button (Fig. 2/4) on the remote control repea- tedly until USB is displayed on the screen. Playback begins automati- cally. NOTE: In order to find out which files can be played back the DVD player now reads the contents of the storage medium. In the case of large storage media this procedure may take a long time. During this time you will see the words “ READ USB“ on the screen. 3. Select the desired file(s) and start playback Page 51, “Selecting file/directory and starting replay“. Media can contain various data/files and directories. Hence, you have to define beforehand which files shall be reproduced. 1. If still not done: insert the CD or DVD into the drive. Or connect a USB storage device. The file selection dialog is displayed now. This is structured as follows: - directory view (1) - file view (2) - currently selected directory and, if applicable, selected file (3): The directory name will be displayed in square brackets. Example: “[directory1] file name2.jpg”. - ”Select Audio Files” button (4): Music files are displayed. - “Select Photo Files“ button (5): Photo files are displayed. - “Select Video Files” button (6): Movie files are displayed. NOTE: In this menu, you can navigate the directory view, file view and selection buttons using the Cursor Buttons ( , ) on the remote control. Note: Numerous reproduction and compression procedures as well as diffe- rences in quality of CDs/DVDs and burned CDs and DVDs are available.
English 52 Stopping the replay Viewing pictures Because of this reason problems with the play of files, (i.e. files may be displayed but cannot be played), may occur in isolated cases. This is not a malfunction of tyhe unit. 2. If the storage media contains different file types (e.g. audio and video files) potentially you might get wrong file type information. Example: You are viewing audio files in the file selection dialog but you’d like to play video files. In this case, select the desired file type using either of the selection buttons, e.g. “Select Audio Files”. For this purpose, navigate to the selection buttons using the Cursor Buttons ( , ) (Fig. 2/24) on the remote control. Confirm your entry by ENTER (Fig. 2/16). NOTE: Selection buttons can be navigated only if corresponding files are present. Hence, if there are no video files on a media the “Select Video Files” button is not enabled. 3. Select the directory to be played. To do so, select the directory over-view using the Cursor Buttons ( , ) (Fig. 2/24) on the remote control. The currently selected directory will be highlighted orange. If desired change the directory using the Cursor Buttons ( , ). 4. Start playback by PLAY (Fig. 2/26). All files of the selected directo- ry will be played back. Select file If you want to play back only one file or if you want to start playback with a certain file proceed as follows: 1. Select as described above, the file type and the directory containing the desired file. Page 51, “Selecting file/directory and starting replay“, item 1-3. 2. Switch to file view using the Cursor Buttons ( , ) (Fig. 2/24) of the remote control. 3. Select the desired file. The currently selected file will be highlighted orange. Change the file if desired using the Cursor Buttons ( , ). Press the STOP-button (Fig. 2/14) on the remote control to stop the replay. The DVD player is suitable for displaying your digital photographs. These photos may be stored only any medium (DVD, CD, etc.) supported by the DVD player. NOTE: Please ensure a suitable size of the photos. Large size photos may take some time to be displayed or may not be displayed at all. It is of advantage if the size of the photo corresponds with the screen size of the playback device. For TVs this is normally 1024x576 pixel (TV-aspect 16:9) or 768x576 (TV-aspect 4:3). Please note that any conversion generally involves a loss of data with respect to the original format. Start the replay of photos by selecting the file from which the replay shall start Page 52, “Selecting file/directory and starting replay“. The pictures change automatically.
English 53 Understand Menu Structure Use the menu Scrolling Manual: Press the (Fig. 2/22) or button (Fig. 2/22) on the remote control to scroll forward or back. Interrupt scrolling: Press the PAUSE button (Fig. 2/27) in order to interrupt the automatic picture change. Press the PAUSE button again in order to resume picture playback. Rotating a photo NOTE: Cannot be done if automatic picture shift is interrupted. You can use the Cursor buttons to rotate a photo during replay: Mirror vertically: Cursor Button “ “ Mirror horizontally: Cursor Button “ “ Rotate clockwise for 90°: Cursor Button “ “ Rotate counter-clockwise for 90°: Cursor Button “ “ Change settings A large number of default settings can be comfortably changed via the screen menu. Press the SETUP button (Fig. 2/25) on remote control to start the menu for changing the default settings. NOTE: Many of this default settings can be changed using the remote control as well as the menu. The difference is: If you change the default set- tings with the remote control, the changes will reset upon turning off the DVD Player or removal of the DVD. Changes made using the menu are permanent. Within the menu setup you will find two menu levels: Main menu: The main menu is displayed by graphic symbols. Sub-menu: Within every main menu entry you will find the corresponding sub-menu entries. Navigation and selection Navigate the main menu by the Cursor Buttons ( / ) (Fig. 2/24) on the remote control. Whereas inside a submenu, you navigate using the Cursor Buttons ( / ). Select a menu item by pressing the ENTER button (Fig. 2/16). An option is also selected by pressing ENTER. The selected option is now highlighted.
English 54 Overview of the main menu System settings Slide control Some menus contain sliders, e.g. to adjust the volume or brightness. Use the sliders as follows: 1. Select it by pressing the ENTER button. 2. Move the control by the Cursor Buttons ( / ). 3. Confirm your input by ENTER. System settings (1) Language settings (2) Audio settings (3) Video settings (4) Speaker settings (5) Digital settings (6) NOTE: Some menu settings are available only in stop mode (depending on the DVD). TV-System Adjust the output of the DVD player to the color transmission system of your reproducer. The following options are available: NTSC: System prevalent mainly in Northern America. PAL: System prevalent in Europe. AUTO: Select this setting if the reproducer is a multi-system device. NOTE: You can switch between the options also by the P/N button (Fig. 2/15). Screen saver The device can display a still image on screen indefinitely. This can cause damage to the screen. Hence, it is useful to enable the screen saver. The following options are available: ON: The screen saver is enabled (standard setting). OFF: The screen saver is disabled.
English 55 HD Output (Resolution) Select the HDMI resolution for the connected reproducer to be used. The selection of the correct signal format depends on the connection in use and the reproducer. (Please refer to the user manual of the reproducer.) Video-Output NOTE: The “Video” menu is only available when the option “HD OFF” in the menu “HD Output” is enabled. You can define the signal format transmitted to your reproducer by the option “Video”. TV-RGB: Select this option if your playback device is connected to the DVD Player with a Scart cable or a composite video cable. S-VIDEO: Select this option, if your playback unit is connected to the DVD Player with an S-Video cable. TV Type Here you can adjust the output of the DVD player to the aspect ratio of your reproducer. Background: If you don’t have a Wide-Screen TV your screen features an aspect ratio of 4:3. Most movies, though, feature an aspect ratio of 16:9 so their image is too wide for the TV set. Here you can set how the image of the movie is adjusted to your reproducer: 4:3 PS: Only the central area of the picture is visible. The edges are cropped (“Pan-Scan”). 4:3 LB: The entire picture is visible but scaled down, thus being framed by black bars on top and bottom (“Letter-Box”). 16:9: Select this option when you have a wide-screen TV set. Please mind that movies taken with an aspect ratio of 4:3 still are displayed in this ratio. Hence, not the full area of the wide-screen TV set is used for the picture. NOTE: The setting “4:3 PS” is not supported by all DVDs.
English 56 Password If you’d like to secure your DVD-Player with a child lock you have to attribute a password first. The password protection saves your child lock settings so they can be modified only by you. To change the password, you have to enter the current password. The default password is “0000“. NOTE: Remember your password. Without this password you can no longer change the child protection function. To change the password, proceed as follows: 1. Enter the current password using the Numerical Buttons (Fig. 2/31) on the remote control. To avoid the password being read by unauthorized persons, only the characters “XXXX” appear on screen. 2. Confirm your entry by pressing ENTER (Fig. 2/16). 3. Now enter your new password with the Numerical Buttons (Fig. 2/31) on the remote control. Rating (child protection) Some DVDs contain information concerning the target group. At this, the procedure is similar to the release of cinema films. (e.g. “released for age 12“). If the child protection option is enabled the respective information (if existing) will be read from the DVD and compared to the value preset by you. If a DVD is intended for a higher age group than the one preset by you the DVD cannot be played back. The following child protection options can be chosen: 1 G: Suitable for children. 2: Suitable for all age groups. 3 PG: Parental supervision is recommended. Some passages might be inappropriate for children. 4 PG 13: Parental supervision is strongly recommended. Some passages can be inappropriate for children under the age of 13. 5: Parental supervision is necessary. 6 R: Youths under 17 may watch the movie only under supervision of an adult. 7 NC17: Children and adolescents under 17 must not watch the movie. 8: The film is to be watched only by adults. Factory Settings Select “Default/ Reset” if you want to reset the device to the factory settings. All of your own settings will be lost.
English 57 Language Setup Audio Setup Video Setup Here, you can choose various language settings. OSD Language: The language of the On-Screen Display. Audio Language: The language for the Audio output. Subtitle Language: The language used for the supportive subtitles of the film. Menu Language: The language of the DVD menu. Audio Output Here, you can set your preferences for the digital audio output. SPDIF/OFF: The output signal will be only analog but not digital. SPDIF/RAW: The output will be digital. Use this setting if your amplifier is not a stereo two-channel amplifier. SPDIF/PCM: The output will be a digital audio signal converted into a 2 channel signal. Use this setting if your amplifier is a stereo two-channel amplifier. NOTE: If there’s no audio output although the DVD-Player is connected to an amplifier you might have selected the wrong setting in this section. Sound (Key) Here you can adjust the speed of the audio output. Here you can choose various settings to adjust the video signal. All settings are adjusted by slide controls. Brightness Contrast Hue Saturation (color saturation) Sharpness
English 58 Downmix Modify the characteristics of the speaker output: LT/RT: Select this setting when you want to play a DVD in Dolby Pro Logic Stereo effect. This produces a 2-channel effect close to reality. Stereo: Select this setting if you want to play a DVD recorded in 5.1 audio format in 2 channel stereo. VSS: Perhaps you don’t have a 5.1 audio unit. In this case, you can emulate a comparable sound by selecting the “VSS” setting. Op Mode (Night mode) Enable the night mode to activate special audio characteristics making the sound less disturbing. Line Out: Night mode is enabled. RF Remod: Night mode is disabled. Dynamic (Dynamic Range) The term “Dynamic Range” defines the ratio of the lowest tone and the loudest. If this Dynamic Range is very high then there is very low volume as well as very loud passages. This might cause some problems for the reproduction. Assume you want to play a DVD in a very noisy environment. You can increase the volume to be able to hear the low-volume passages but this entails that the loud passages become inappropriately noisy. Hence, it is useful to compress the dynamic range (i.e. decrease) and increase the volume at the same time. FULL -2/8: The dynamic range is compressed slightly (2/8) to maxi- mum (FULL). OFF: The dynamic range is uncompressed (factory setting). Dual Mono Normally, the sound output is in stereo. Here, you can choose a mono output instead of stereo. Stereo: The output is in stereo (factory setting). Left: The output is in mono. All speakers will receive the left stereo channel signal. Right: Output is set to mono. All speakers will receive the right stereo channel signal. Mix Mono: Output is in mono. All speakers will receive both stereo channels. Speaker Setup Digital Setup
English 59 Radio Station Set-up This device has a built in FM radio receiver. There are 3 ways to scan through the radio stations: Automatic Scan, Manual Scan and Direct Frequency Input. Auto scan 1. Use the FUNCTION button (Fig. 2/4) to select the RADIO mode. 2. Press the SEARCH button (Fig. 2/17). The device is now scanning the current frequency band for stations and saves them automatically. NOTE: Also use the (Fig. 1/6) button on the device to start the automatic station scan. The station order cannot be changed. Manual scan 1. Use the FUNCTION button (Fig. 2/4) to select the RADIO mode. 2. Use the or buttons (Fig. 2/22) to select the storage location at which you want to save the station. 3. Press the “ “/“ “ buttons (Fig. 2/18) to search for a station. Press the corresponding button repeatedly until you have found the desired radio station. 4. Use the MEM button (Fig. 2/23) to play back the radio station that has been found. Use the “ “/“ “ buttons (Fig. 2/22) to select a saved radio station. Troubleshooting Before sending the machine to the Customer Services, use the following table to check whether you can rectify the fault yourself. Fault Possible cause Solution No display No power supply WARNING: Before troubleshooting, switch the player off. Put the mains plug in correctly, if necessary, check the socket is working with another appliance. no power supply/mains switch switched off Switch the player on by the mains switch (Fig. 1/25). No image displayed on screen Video cable not correctly con- nected WARNING: Before troubleshooting, switch the player off. Check the correct fit of the Video cable “Connecting the Video cable“. Make sure that the jacks are tightly in the sockets. no DVD/CD inserted Insert a CD/DVD. DVD/CD not compatible Use only compatible media (see “Technical data“). DVD/CD incorrectly placed in CD/DVD-tray Turn the CD/DVD around. CD/DVD is dirty Clean the CD/DVD.
English 60 Disposal At the end of the service life of the appliance, in particular if it is mal- functioning, make the appliance unusable by pulling the mains plug out of the socket and separating the power cable. Dispose of the appliance according to the environmental regulations applicable in your country. Electrical waste may not be disposed of together with household waste. For any advice regarding recycling, contact your local municipal authori- ties or your dealer. Declaration of conformity Clatronic International GmbH hereby declares that the device MC 4445 DVD is in conformity with the basic requirements of the European guideline for electromagnetic compatibility (2004/108/EG) and the low voltage guideline (2006/95/EG). Amplifier switched off If you use an amplifier for Audio output: check whether the amplifier is switched on. Incorrect settings Check the settings of your DVD-Player. Internal speakers are disabled Keep the MUTE button pressed (Fig. 2/21) for around 3 seconds to turn the internal speaker on again. No sound via SCART, audio output, COAXIAL output Device volume is too low or set to "00" Use the VOLUME+/VOLUME- buttons (Fig. 2/19) to set the volume to a higher level. The remote control does not work wrong direction The remote control is not pointed towards the DVD- Player. too far away Make sure that the remote control is not further than 7 m away from the player. Batteries empty Replace the batteries in the remote control “Remote control battery installation“. Titles are played in wrong order Playlist is used Delete the playlist “Deleting a Playlist“. DVD cannot be played DVD has not been finalized Use a finalized DVD. Poor radio reception. The received radio station is too weak for a stereo operation. Adjust the device to mono operation by pressing the ST/MO button (Fig. 2/20). Fault Possible cause Solution No image displayed on screen CD/DVD is damaged Use a different CD/DVD. Incorrect settings Check the settings of your DVD-Player. The child lock system is acti- vated Deactivate the child lock “Parental“. No response when press- ing button Power supply problem or static charging of appliance Switch off the main switch and pull out the mains plug. Insert the mains plug into the socket and switch the player on again. No sound Audio cable not connected WARNING: Before troubleshooting, switch the player off. If you are not using a SCART plug to transmit video sig- nals, you have to use an additional audio cable beside the video cable “Connecting an audio cable“.
English 61 OSD Menu Overview SYSTEM SETUP TV SYSTEM NTSC PAL AUTO SCREEN SAVER ON OFF HD OUTPUT HD OFF 720P 1080i 1080P VIDEO TV-RGB S-VIDEO TV TYPE 4:3PS 4:3LB 16:9 PASSWORD - - - - RATING 1 G 2 3 PG 4 PG13 5 6 R 7 NC-17 8 DEFAULT RESTORE LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG AUDIO SETUP AUDIO OUT SPDIF/OFF SPDIF/RAW SPDIF/PCM KEY VIDEO SETUP BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS SPEAKER SETUP DOWNMIX LT/RT STEREO VSS DIGITAL SETUP OP MODE LINE OUT RF MODE DYNAMIC RANGE DUAL MONO STEREO MONO L MONO R MIX MONO
Have a question about the AEG MC 4445 DVD but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the AEG MC 4445 DVD. Please make sure that you describe your difficulty with the AEG MC 4445 DVD as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.