AEG CDP 4200 manual

View a manual of the AEG CDP 4200 below. All manuals on can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view.

  • Brand: AEG
  • Product: CD-player
  • Model/name: CDP 4200
  • Filetype: PDF
  • Available languages: Dutch, English, German, French, Spanish, Italian, Portuguese, Polish, Russian, Norwegian, Slovak, Hungarian

Table of Contents

Page: 24
General safety instructions
To avoid the risk of fire or an electric shock, you should
not expose the device to rain or moisture. Consequently,
do not use the device in the immediate vicinity of water
- for example near a bath tub, a swimming pool or in a
damp cellar.
Use the device only for the intended purpose.
Only connect the device at a properly installed plug
socket. Pay attention that the specified voltage corres-
ponds to the voltage of the plug socket.
When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries
in the correct direction.
Assemble the device in such a way that the available
ventilation openings are not covered.
Never open the housing of the device. Incorrect repairs
can constitute a considerable risk for the user. Should
the device become damaged, in particular the mains
supply cable, do not operate the device any longer, but
rather have it repaired by an expert. Check the mains
supply cable regularly for damage.
For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manuf-
acturer, our customer service department or a similary
qualified person.
If the device is not used for a longer period, remove the
plug connector from the plug socket or take out the
These symbols may be found on the machine and are
intended to indicate the following:
The lightning symbol should advise the user
of parts in the inside of the device which carry
dangerously high voltage levels.
The symbol with an exclamation mark should
advise the user of important operation or
maintenance instructions in the accompa-
nying documentation.
Devices bearing this symbol work with a
„class 1 laser“ for tracing the CD. The built-in
safety switches should prevent the user being
exposed to dangerous laser light, which is
invisible to the human eye, when the CD compartment
is opened.
Under no circumstances should these safety switches
be bypassed or manipulated, as this could result in a
danger of exposure to the laser light.
Commissioning the device
Battery Mode (not supplied)
• Open the battery compartment on the inside of the
• Insert 2 1.5V AA type batteries. Match the polarities
correctly (see the inside of the battery compartment).
• If the device is not used for a long period of time, remo-
ve the batteries to avoid the „spilling“ of battery acid.
• A battery symbol in the display indicates that the bat-
teries need changing. Always change the complete
set of batteries, do not replace only one battery.
Warning: batteries are not to be disposed of together
with domestic wastes. Dispose of the used batteries at
the relevant collection bin or at your dealer’s.
Never throw batteries into the fire.
AC Adapter Mode (not supplied)
You can also use the device with an adapter.
1. Insert the AC adapter into a duly installed 230V/50Hz
protective contact outlet.
2. Connect the CD player to the AC adapter by connec-
ting the jack of the adapter into the 4.5V/DC socket.
3. When using an adapter match the polarities correctly
as indicated on the CD player.
General Operating
LINE-OUT: for connection to a stereo sys-
tem, for example.
PHONES: for connecting head- or earpho-
VOLUME: is used to set the volume of the
OPEN: For opening the CD compart-
4,5 V socket: for connecting a mains adapter.
HOLD: it blocks the functions of all the
device’s keys to protect against
their accidental activation. If the
switch is pushed to the right,
the word „HOLD“ appears in the
CHARGE ON/OFF: This switch is located on the
bottom of the device. The char-
ging function is activated when
connected to an external mains
Make sure that there are no
batteries in the battery compart-
ment. Danger of explosion! Use
only appropriate rechargeable
Note: In order to create the con-
tact to the battery, please use the
charging socket supplied.
Switching off
The machine is switched off by pressing the STOP
button once, or twice if one of the devices is still running.
It will also switch off automatically if not operated for
approx. 30 seconds.
5....-05-CDP 4200 AEG 25 13.04.2004, 11:09:47 Uhr
Page: 25
Playing CDs
1. Shift the OPEN key to the right to open the CD com-
2. Insert a CD with the label facing upwards and press
carefully over the button until it snaps into place.
Close the CD compartment.
3. Press the PLAY/PAUSE button to switch the device
on and play back the CD. „--“ appears in the display,
i.e. number of tracks and the total running time. The
CD starts from the first track. The track currently
being played and the time that has elapsed are
shown in the display.
4. To remove a CD, press the STOP key, open the CD
deck with the OPEN key and take out the CD carefully.
Please note these instructions for playing back CDs
and CDRs in MP3 format! The device is not able to
play back MP3 files. The CD begins to turn, but the
sound cannot be heard.
Always keep the CD deck cover closed.
Note: If a disc is inserted incorrectly, or no disc is inser-
ted, the symbol „DISC“ appears in the display.
Description of the CD buttons:
PLAY/PAUSE  / II: You can briefly interrupt the
playing. Renewed pressing of the
button will re-start the playing
from the same place.
STOP : The CD is stopped. By pressing
once again, the unit is switched
BBS (BASS BOOST): increases the bass sound. Press
repeatedly to switch between
BOOST 1 and BOOST 2.
PROG: See under “Programmed Play”.
MODE: The following functions can be
selected with the MODE key:
Press once =
„ 1“: the current track is
repeated continuously.
Press a second time =
„ ALL“: the whole CD is
played continuously.
Press a third time =
Then press the PLAY/PAUSE
button. „INTRO“: All tracks are
played for ten seconds. The word
„INTRO“ appears in the display.
Press a fourth time =
The word „SHUFF“ appears in
the display (during playback).
If the PLAY/PAUSE button is
pressed, all tracks are played
back in random order.
Press a fifth time =
all the functions are reset.
The normal play mode is resu-
ESP (Anti-Shock): It fills the 45-second electronic
memory to protect against the
jumping of the CD. When anti-
shock is activated a bar appears
in the display which slowly fills
up. Press the button again to
deactivate this function.
I SKIP -: Press once =
This starts the current track again
from the beginning.
Press a second time =
This jumps back to the previous
Press a third time =
This plays the song before etc. If
the button is kept pressed down,
the machine starts to search
through the tracks (The sound is
I SKIP +: With this button you can jump
to the following track or the next
track but one etc. If the button is
kept pressed down, the machine
starts to search through the
Programmed Play
1. Press the PROG key.
2. PROG and „00“ (track number) flashes on the
display. The memory slot number can be seen on the
3. Use the I / I SKIP buttons to select the desi-
red track and then press the PROG button again.
4. The display changes to memory slot 02.
5. Repeat the procedure until all the desired tracks are
selected. If the SKIP -/+ buttons are pressed, the
order in which the tracks are stored is displayed.
6. Press the PLAY/PAUSE key. The playback starts.
Press this button to pause briefly the playback.
7. Press once the STOP key to stop the playback while
retaining the program.
8. To resume the playback of the program press first the
PROG key once and then the PLAY/PAUSE key.
9. To delete the program, press the STOP key twice
(The machine switches off) .
The device stops automatically once the entire sequence
of programmed tracks is completed. The programmed
sequence remains in the memory until the CD is taken
out of the CD deck or until the device is switched off.
It is possible to combine the pre-programmed tracks
with the MODE function. After you have programmed the
tracks and started the machine, please press the MODE
button up to fourth times so that the functions „ 1“, „
ALL“ and „INTRO“ can be used as described in the
section entitled „MODE“.
This device has been tested according to all relevant cur-
rent CE guidelines, such as electromagnetic compatibili-
ty and low voltage directives, and has been constructed
in accordance with the latest safety regulations.
Subject to technical changes without prior notice!
5....-05-CDP 4200 AEG 26 13.04.2004, 11:09:48 Uhr
Page: 26
The device supplied by our Company is covered by a
24 month guarantee starting on the date of purchase
During the life of the guarantee any fault of the device or
its accessories *) ascribable to material or manufacturing
defects will be eliminated free of charge by repairing or,
at our discretion, by replacing it. The guarantee services
do not entail an extension of the life of the guarantee nor
do they give rise to any right to a new guarantee!
Proof of the guarantee is provided by the proof of
purchase. Without proof of purchase no free replacement
or repair will be carried out.
For repairs or replacement during the life of the guaran-
tee return the device in its original packing together with
the proof of purchase to your dealer.
*) Damage to accessories does not mean automatic free
replacement of the whole machine. In such cases please
contact our hotline. Broken glass or breakage of plastic
parts are always subject to a charge.
Defects to consumables or parts subject to wearing
(e.g. motor pistons, kneading blades, drive shafts, spare
remote control, spare toothbrushes, saw blades, etc.) as
well as cleaning, maintenance or the replacement of said
parts are not covered by the guarantee and hence are
to be paid!
The guarantee lapses in case of unauthorized tampering.
After the expiry of the guarantee
After the expiry of the guarantee repairs can be carried
by the competent dealer or repair service against the
payment of the ensuing costs.
5....-05-CDP 4200 AEG 27 13.04.2004, 11:09:49 Uhr

Question & answers

There are no questions about the AEG CDP 4200 yet.

Ask a question about the AEG CDP 4200

Have a question about the AEG CDP 4200 but cannot find the answer in the user manual? Perhaps the users of can help you answer your question. By filling in the form below, your question will appear below the manual of the AEG CDP 4200. Please make sure that you describe your difficulty with the AEG CDP 4200 as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.